SERVICE MANUAL

SOUND AMPLIFIER BOX

MODEL: TR200A

1. TECHNICAL SPECIFICATIONS
FM RADIO SECTION MIC input 1 6.3mm (P10)
Tuning System PLL Sensitivity 1mV
Frequency Range 76,1 ~ 107,9 MHz MIC input 2 6.3mm (P10)
Practical Sensitivity ≤40 dB Sensitivity 1mV
Signal to Noise Ratio ≥ 50 dB AUDIO SECTION
Total Harmonic Distortion <= 2.0% Output Power 2 x 7.0W
BLUETOOTH SECTION Impedance of the Speakers
Version 2.1 Woofer 2x4
Scope 10m Twitter 6
Supported Profiles A2DP v1.2; AVRCP v1.0; HFP v1.5 Volume Control Digital
Distortion ≤ 2.0% Equalizer 5 types
USB SECTION GENERAL
File types MP3 & WMA Feeding: AC/DC Adapter 127 /220V AC 50/60Hz
Supported bitrates 8 at 320kbps and variable 9.0V 1000mA
Total Harmonic Distortion <= 2.0 %
Formatting FAT 16 and 32 Internal Battery Lithium Ions
Capacity Up to 32GB Type 18650x2
Tension 7.4V
LINE IN input Capacity 2000mAh
Sensitivity 300mV Average Power Consumption 3W
Distortion <= 2.0% Dimensions
Signal Noise Ratio ≥ 60 dB Device 340(L)X 515(A) X 320(P)
Socket 3.5mm (P2) Weight 6.20kg
1st Issue Sep/2018

SEMP TCL
2. SAFETY PRECAUTIONS
SEMP TCL
2.1. SAFETY PRECAUTION ITEMS:
2.1.1. Before returning the device to the customer, always check the following items of
device:
[Link]. Make sure there is no damaged protective component before or after
of the service, on the device.
[Link]. PROTECTIVE BLANKETS (Plastic covers, insulators, heat-shrinkable sleeves, foams of
drunk, etc.), are placed in the devices for the protection of the client and the technician.
Reinstall or replace these protective shields in the same location where they were.
withdrawals, leaving the device in its original conditions.
2.1.2. Do not handle or allow the handling of devices without all protective components.
are correctly installed and functioning.
2.2. ACCESS TO THE DEVICE:
Ensure there are no openings in the cabinet (once assembled) where children or adults may have access.
access and touch 'live' (electrically energized) parts, causing shocks. Do not replace or
modifying the cabinet or parts of it with non-original parts, leaving openings that are very large where they
may access living parts.

2.3. INSULATION RESISTANCE

2.3.1. Disconnect the power cord from the outlet and short-circuit its terminals.
2.3.2 Turn on the POWER switch (On/Off) of the device, if available, or turn on some function. TV by
example.
2.3.3. Measure with a Megohmmeter, the resistance between the terminals of the short-circuited power cable and
all exposed metal parts of the device, such as screws, telescopic antenna, terminals of
antenna, input/output terminals, output terminal for headphones, etc. If the metal part has a return of
current through the chassis, we should find values between 1 and 5.2 megohms. If the metal part does not have
current return through the chassis, the instrument should indicate values much higher than these.
If none of these limits are met, there is some metallic part short-circuited with the chassis.
potentially causing electric shocks, explosions, or even fires.
2.4. SECURITY COMPONENTS
2.4.1. Some electrical and mechanical components have special characteristics to meet the
security requirements are not identified only by visual inspection.
These components cannot be replaced by similar ones of higher voltage, power, or
heat dissipation, etc.
2.4.3. The component should be identified by an electrical diagram or mechanical drawing
normalized (which will indicate whether the component is or is not safety-related) of the device, and thus
replace it. This measure will prevent damage to the device, the technician, and the customer. These components
are identified by the symbol .
2.4.3. Security components are being continuously reviewed and new specifications are
released.
2.5. TECHNICAL ASSISTANCE PRECAUTIONS:
ATTENTION: Before performing any maintenance mentioned in this Service Manual, read and follow the
Item 2.1. SAFETY PRECAUTION ITEMS. NOTE: If for any reason there is a conflict or
doubts between TECHNICAL ASSISTANCE PRECAUTIONS and PRECAUTION ITEMS
SAFETY, always follow the SAFETY PRECAUTION ITEMS.

2.5.1 Always disconnect the appliance power cord from the outlet when:
[Link] Remove or install any component, circuit board, module, or other assembly.
[Link] Disconnect or connect any connector of the device.
[Link] When connecting a measuring instrument, always connect the ground terminal first.
ground instrument from the plate that will be measured. Always remove the ground terminal from
instrument finally.
2.5.2. When the maintenance of a device is finished, set the voltage selector switch to
(there is), in the position of 220V.

2 Return
Index
SEMP TCL
1. TECHNICAL SPECIFICATIONS................................................................................................................................................... 1
2. SAFETY PRECAUTIONS
2.1. SAFETY PRECAUTION ITEMS: ........................................................................................................................................... 2
2.2. ACCESS TO THE DEVICE: .................................................................................................................................................................... 2
2.3. INSULATION RESISTANCE
2.4. SECURITY COMPONENTS
2.5. TECHNICAL ASSISTANCE PRECAUTIONS:.......................................................................................................................................... 2
3. COMMANDS AND FUNCTIONS
4. ELECTRICAL SCHEMES
5. EXPLODED VIEW
6. LIST OF REPLACEMENT PARTS ............................................................................................................................................ 8
3. COMMANDS AND FUNCTIONS
SEMP TCL

1- Power/Standby button and INPUT: Press and 11- Auxiliary Input (LINE IN)
hold for 3 seconds to turn on 12- USB Port: Connect a USB device
or turn off the device. Press quickly in the USB port for MP3 music playback
to change function.
2- PLAY/PAUSE Button Press it to
start or temporarily pause playback
from USB or BT.
3- Volume Button: Rotate the button and control the
Volume of sound, increasing or decreasing.
MENU: Press the volume button to
select the various adjustment options such as
niveis de graves, agudos, eco, delay,
lighting etc.
4- LED Display: Indicates the functions of USB, BT,
and Radio.
5- Back button To play the track
forward in USB/BT. In FM, jumps to the APP Speaker Pro, for available control for
previously memorized broadcaster. download from the following app stores:
6- Forward Key To jump to the next
band in USB/BT. On FM, it skips to the next one
memorized broadcaster.
7- Input for the DC adapter cable.
8- Battery status indicator
9- MICROPHONE1
10- MICROPHONE2
.
4. ELECTRICAL SCHEMES
SEMP TCL
4. ELECTRICAL SCHEMATICS

SEMP TCL
5. EXPLODED VIEW
6. LIST OF REPLACEMENT PARTS
SEMP TCL

NE Description
820578 GRADE TR200A
820582 ALTO FAL WOOFER 12" 3+3R TR200A
820584 TR200A CABINET CONJ
820579 TRANSPORT LOCK TR200A
820576 PCI PRINCIPAL TR200A MONT
820580 REAR TAMP TR200A
820585 RODIZIO TR200A
820575 AC/DC adapter 9V/1A TR200A
820577 ALTO FAL TWEETER 4OHMS TR200A
820587 LITHIUM ION BATTERY 2000MAH/7.4V TR200A
860084 INDIVIDUAL BOX TR200A
860086 CALCO LOWER EPS TR200A
860085 CALCO EPS SUPERIOR TR200A
820586 DISPLAY LENS TR200A
820581 TR200A MANUAL INSTRUCTIONS
820583 PCI LED TR200A MOUNT

8 Turn
 SEMP TCL
Av. Arnaldo Rojek, 01–Altos de Jordanésia–Cajamar - S.P.
ZIP Code 07786-900

Tel.: PABX ( 0XX11 ) 3232-2200