FILTERS Defender® Filter Schematic - Automatic

AUXILIARY EQUIPMENT SUCH AS

HEATERS, CHEMICAL SAMPLE AND FEED
DEFENDER FILTER COMPONENTS - INCLUDED IN DEFENDER PACKAGE
LINES, ETC. MUST BE LOCATED MARK REFERENCE NOTES
DOWNSTREAM OF THE EFFLUENT VALVE PNEUMATIC BUMPING
D1
ASSEMBLY
D2 QUICK EXHAUST VALVE
F23 F26 D3 LIFTING DAVIT NONE
D4 VIEWING WINDOW
D5 GAUGE PANEL
D6 INFLUENT CHECK VALVE
F22 AIR OPERATED BUTTERFLY VALVE, NORMALLY
OPEN. INSTALL EFFLUENT VALVE DIRECTLY ON
F27 D7 EFFLUENT VALVE
PRECOAT TEE. LOCATE ACTUATOR WHERE
VALVE CAN BE VIEWED FROM FLOOR.
AIR OPERATED BUTTERFLY VALVE, NORMALLY
CLOSED. INSTALL PRECOAT VALVE AS CLOSE
F25 AS POSSIBLE TO THE PUMP SUCTION PIPING.
D8 PRECOAT VALVE
PRECOAT LINE 2 PIPE DIAMETERS SMALLER
F37 F24 THAN EFFLUENT PIPE DIAMETER. (NO LESS
THAN 2”)
F27 D9 SYSTEM FILL
MANUALLY OPERATED BUTTERFLY VALVE,
NORMALLY OPEN.
MANUALLY OPERATED BUTTERFLY VALVE,
NORMALLY CLOSED, WITH EXTENSION. BOLTED
D10 DRAIN VALVE DIRECTLY TO TANK BOTTOM (MEDIA DUMP /
RINSE) DRAIN LINE MUST BE PLUMBED
D7 INDEPENDENTLY TO WASTE
3/4” VENT D3 INSTALL IN-LINE SIGHT GLASS ON THE PRECOAT
LINE D1 D2 D11 IN-LINE SIGHT GLASS LINE SO THAT IT CAN BE VIEWED WHILE
STANDING AT THE FILTER CONTROL PANEL
REQUIRED D12 RMF CONTROL PANEL
FLANGE BREAK D11 D13 FILTER REGULATOR
D6 NONE
D14 VACUUM TRANSFER UNIT
D15 VACUUM TRANSFER HOSE
D16 F30
D8 D16
VACUUM TRANSFER PIPING SCH80 PVC FITTINGS & PIPE 1.5”
& FITTINGS
F28 D17 VACUUM TRANSFER VALVE
BALL VALVE 1.5” TRUE UNION, NORMALLY
D14 CLOSED.
D9 F29 BALL VALVE 1.5” TRUE UNION, NORMALLY
D18 VACUUM VENT VALVE CLOSED. VACUUM DRAIN LINE MUST BE
D15 PLUMBED INDEPENDENTLY TO WASTE
VACUUM HOSE VALVE WITH BALL VALVE 1.5” TRUE UNION, NORMALLY
D19
F31 HOSE CLOSED.
D5 D20 AIR COMPRESSOR
OPTIONAL
D21 WATER SEPARATOR
D17 F32
D4 FILTER ACCESSORY COMPONENTS – AVAILABLE UPON REQUEST
F35 F33 MARK REFERENCE NOTES
D18
F22 GREEN DRIVE VFD NONE
ETS UV TREATMENT
F23
SYSTEM CONTROLLER
D19 F34 ETS UV TREATMENT THIS IS A PACKAGE
F24
SYSTEM
D13 F25 ETS UV STRAINER
GEAR OPERATED BUTTERFLY VALVE,
F26 ETS UV BYPASS
NORMALLY CLOSED.
D10 D12 GEAR OR LEVER OPERATED BUTTERFLY VALVE,
F27 ETS UV ISOLATION
NORMALLY OPEN. (2) REQUIRED
FOR SELF PRIMING PUMPS, CHECK VALVE MUST
F28 CHECK VALVE BE INSTALLED ON SUCTION PIPE BELOW WATER
NOTES: LEVEL.
F29 GUARDIAN™ STRAINER NONE
EQUIPMENT SHOWN FOR SCHEMATIC PURPOSES ONLY. REFER TO PROJECT LEVER OR GEAR OPERATED BUTTERFLY VALVE,
F30 STRAINER ISOLATION
PROPOSAL AND SUBMITTALS FOR EQUIPMENT SUPPLIED BY NEPTUNE-BENSON. NORMALLY OPEN.
D21 F31 PRECOAT REDUCING TEE NONE
PNEUMATIC TUBING OR WIRING NOT SHOWN FOR CLARITY. GEAR OPERATED BUTTERFLY VALVE,
F32 PUMP THROTTLE VALVE
NORMALLY OPEN.
F36 F33 RECIRCULATING PUMP
NONE
F34 PUMP BASE
NORMALLY CLOSED, PRECOAT LINE MUST BE
D20 F35 PRECOAT LINE VENT VALVE
PLUMBED INDEPENDENTLY TO WASTE.
F36 1/2” SHUT OFF VALVE NONE
F37 FLOW METER NONE
R-10/29/14 WASTE PIT – MINIMUM 300 GPM CAPACITY

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
 FILTERS Defender® Filter Schematic – Automatic
AUXILIARY EQUIPMENT SUCH AS DEFENDER FILTER COMPONENTS - INCLUDED IN DEFENDER PACKAGE
HEATERS, CHEMICAL SAMPLE AND FEED MARK REFERENCE NOTES
LINES, ETC. MUST BE LOCATED PNEUMATIC BUMPING
D1
DOWNSTREAM OF THE EFFLUENT VALVE ASSEMBLY
D2 QUICK EXHAUST VALVE
NONE
F22 D3 VIEWING WINDOW
F25 D4 GAUGE PANEL
D5 INFLUENT CHECK VALVE
GEAR OPERATED BUTTERFLY VALVE, NORMALLY
OPEN. INSTALL EFFLUENT VALVE DIRECTLY ON
F21 D6 EFFLUENT VALVE
PRECOAT TEE. LOCATE ACTUATOR WHERE VALVE
F26 CAN BE VIEWED FROM FLOOR.
AIR OPERATED BUTTERFLY VALVE, NORMALLY
CLOSED. INSTALL PRECOAT VALVE AS CLOSE AS
D7
PRECOAT VALVE POSSIBLE TO THE PUMP SUCTION PIPING.
F24 PRECOAT LINE 2 PIPE DIAMETERS SMALLER THAN
EFFLUENT PIPE DIAMETER. (NO LESS THAN 2”)
F36 MANUALLY OPERATED BUTTERFLY VALVE,
D8 SYSTEM FILL
F23 NORMALLY OPEN
F26 MANUALLY OPERATED BUTTERFLY VALVE,
D6 D9 DRAIN VALVE
NORMALLY CLOSED (MEDIA DUMP / RINSE) DRAIN
LINE MUST BE PLUMBED INDEPENDENTLY TO
WASTE
INSTALL IN-LINE SIGHT GLASS ON THE PRECOAT
3/4” VENT D10 IN-LINE SIGHT GLASS LINE SO THAT IT CAN BE VIEWED WHILE STANDING
LINE D1 AT THE FILTER CONTROL PANEL
D11 RMF CONTROL PANEL
REQUIRED D12 FILTER REGULATOR
D2 NONE
FLANGE BREAK D13 VACUUM TRANSFER UNIT
D15 D10 VACUUM TRANSFER
D5 D14
HOSE
VACUUM TRANSFER
D13 D7 F29 D15
PIPING & FITTINGS
SCH80 PVC FITTINGS & PIPE 1.5”
VACUUM TRANSFER BALL VALVE 1.5” TRUE UNION, NORMALLY CLOSED.
F27 D16
VALVE
D8 F28 BALL VALVE 1.5” TRUE UNION, NORMALLY CLOSED.
D17 VACUUM VENT VALVE VACUUM DRAIN LINE MUST BE PLUMBED
INDEPENDENTLY TO WASTE
D4 VACUUM HOSE VALVE BALL VALVE 1.5” TRUE UNION, NORMALLY CLOSED.
D18
WITH HOSE
D16 D14 F30 D19 AIR COMPRESSOR
OPTIONAL
D3 D20 WATER SEPARATOR
F34 D17 F31 FILTER ACCESSORY COMPONENTS – AVAILABLE UPON REQUEST
F32 MARK REFERENCE NOTES
F21 GREEN DRIVE VFD NONE
D18 ETS UV TREATMENT
F22
SYSTEM CONTROLLER
F33 ETS UV TREATMENT THIS IS A PACKAGE
F23
SYSTEM
D11 F24 ETS UV STRAINER
D9 F25 ETS UV BYPASS
GEAR OPERATED BUTTERFLY VALVE, NORMALLY
D12 CLOSED.
GEAR OR LEVER OPERATED BUTTERFLY VALVE,
F26 ETS UV ISOLATION
NORMALLY OPEN. (2) REQUIRED
FOR SELF PRIMING PUMPS, CHECK VALVE MUST
F27 CHECK VALVE BE INSTALLED ON SUCTION PIPE BELOW WATER
NOTES: LEVEL.
F28 GUARDIAN™ STRAINER NONE
EQUIPMENT SHOWN FOR SCHEMATIC PURPOSES ONLY. REFER TO PROJECT LEVER OR GEAR OPERATED BUTTERFLY VALVE,
F29 STRAINER ISOLATION
PROPOSAL AND SUBMITTALS FOR EQUIPMENT SUPPLIED BY NEPTUNE-BENSON. NORMALLY OPEN.
D20 F30 PRECOAT REDUCING TEE NONE
PNEUMATIC TUBING OR WIRING NOT SHOWN FOR CLARITY. GEAR OPERATED BUTTERFLY VALVE, NORMALLY
F31 PUMP THROTTLE VALVE
OPEN.
F35 F32 RECIRCULATING PUMP
NONE
F33 PUMP BASE
PRECOAT LINE VENT NORMALLY CLOSED, PRECOAT LINE MUST BE
D19 F34
VALVE PLUMBED INDEPENDENTLY TO WASTE.
F35 1/2” SHUT OFF VALVE NONE
R-10/29/14 WASTE PIT – MINIMUM 100 GPM CAPACITY F36 FLOW METER NONE

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
 Defender® Filter Model Shipping
FILTERS Dimensional & Weight Information
With Pallet Tank Ship
Model Number A B Weight
in in lb
SP-24-42-327 48 82.5 1450
SP-27-48-487 48 87.5 1650
SP-33-48-732 48 95 1800
Tank Ship SP-41-48-1038 60 99.5 2350
Model Number Weight With Shipping Legs
lb SP-49-48-1548 72 96 3320
SP-29-36-250 800 SP-55-48-2076 72 96 3850
SP-29-36-450 860

B
86” B

Custom
Shipping
Leg

6” Shipping Pallet 48” x 48” 6” Shipping Pallet

Models SP-29-36-250, SP-29-36-450
A A
Models SP-24-42-327, SP-27-48-487, Models SP-49-48-1548 & SP-55-48-2076
SP-33-48-732 & SP-41-48-1038
 Models SP-24, SP-27, SP-29 & SP-33 are bolted to a 4’ x 4’ x 6” shipping pallet.

 Model SP-41 is bolted to a 5’ x 5’ x 6” shipping pallet.

 Models SP-49 & SP-55 have (4) custom shipping legs bolted to the filter legs for lifting with a fork truck. R-2/10/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

FLEXSOL 3000® INTERIOR LINING

A. All interior surfaces shall be grit blasted to white metal condition with a 3-4 mil profile. Blasted
surfaces shall be cleaned of all dust or blast residue. Lining shall be applied as soon as is
practical on the same day blasting is done.

B. Flexsol 3000® shall be a urethane, 100% solid plural component lining. Hardness shall be 75
durometer on the shore D scale. Break tensile strength shall be 4000 psi with elongation of
less than 10%. Adhesion shall be greater than 2500 psi.

C. Application of Flexsol 3000® lining shall be done by experienced applicators using a high
pressure, high temperature plural component system. All wetted surfaces including flange
faces, manway rings and manway covers shall be lined to 100 mils +/- 10 mils WFT.

D. Hardness shall be verified after curing to ASTM D 2240 standard.

E. Manufacturer shall submit for approval a sample piece of coated steel to determine flexibility,
abrasion tolerance and adhesion integrity.

F. Flexsol 3000® lining shall meet the NSF toxicity standard unconditionally and shall be approved
for use with the NSF approved filter.

G. Flexsol 3000® lined vessels shall carry a ten-(10) year limited non-prorated warranty against
tank leaks.

H. The filter manufacturer shall bear the responsibility for suitability of lining and shall be the sole
source for the specified warranty.

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

DOMINION™ BUTTERFLY VALVES

NYLON COATED BODY AND DISC

BODY
 Cast aluminum, semi-lug body with flange lug drilling to meet most ANSI 125/150
specifications.
 RILSAN® Nylon 11 coated.
 2” minimum neck length clearance.

STEM AND DISC

 Through-stem direct drive design requiring no disc screws or pins to connect stem to disc with no
possible leak paths in disc stem connections.
 Stem mechanically retained in body neck with corrosion-resistant 304 stainless steel retainer ring.
 Spherically machined, hand-polished disc edge and hub for minimum torque and maximum sealing
capability.
 No part of the stem shall be exposed to line media.

SEAT
 Tongue-and-groove seat design with primary hub flat seal and a molded o-ring suitable for
weld-neck and slip-on flanges.
 Seat totally encapsulates the body with no flange gaskets required.
 Seat should be interchangeable with all other valve styles of manufacturer.

STEM SEAL AND BUSHING

 Equipped with fixed stem seal and non-corrosive nylon-6 bushings.

PRESSURE RATINGS
 All valves must be factory tested for bubble-tight shutoff to 110% of it’s pressure rating.
 All valves must be rated bi-directionally to the full pressure rating specified.

MATERIAL SPECIFICATIONS
 BODY: RILSAN® - Nylon 11 coated cast aluminum – ASTM B179S12C/DIN 1706AC44100 (2”-12” SIZES)
RILSAN® - Nylon 11 coated ductile iron – ASTM A395M:88/DIN ENJS 1020 EN1563 (14”-16” SIZES)
 DISC: RILSAN® - Nylon 11 coated ductile iron – ASTM A395M:88/DIN ENJS1020EN1563
 STEM: 420 SS – AISI grade 420
 SEAT: EPDM

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

INFLUENT CHECK VALVE

4 5
ØD1
3
2 R t
1
ØD2
ØD
7

Size D D1 D2 L R t Weight Nominal Nominal

Part
DIN ANSI Pressure Pressure
No. mm in mm in mm in mm in mm in mm in kg lbs
PN16 125 (Mpa) (PSI)
13600 DN50 2 107 102 65 2.6 40 1.6 43 1.7 29 1.1 19 .74 1.53 3.4 1 1.6 145 232
13601 DN65 2.5 127 121 80 3.1 60 2.4 46 1.8 36 1.4 20 .78 2.44 5.4 1 1.6 145 232
13603 DN80 3 142 134 94 3.7 70 2.8 64 2.5 43 1.7 28 1.1 3.60 7.9 1 1.6 145 232
13604 DN100 4 162 171 117 4.6 88 3.5 64 2.5 53 2.1 27 1.1 5.72 12.6 1 1.6 145 232
13605 DN125 5 192 193 145 5.7 115 4.5 70 2.8 66 2.6 30 1.2 7.34 16.2 1 1.6 145 232
13606 DN150 6 218 219 170 6.7 134 5.3 76 3.0 79 3.1 31 1.2 9.00 19.8 1 1.6 145 232
13607 DN200 8 273 276 224 8.8 162 6.4 89 3.5 104 4.1 33 1.3 17.2 37.9 1 1.6 145 232
13608 DN250 10 328 336 265 10.4 220 8.7 114 4.5 127 5.0 50 2.0 26.3 58.0 1 1.6 145 232
13609 DN300 12 378 406 310 12.2 260 10.2 114 4.5 148 5.8 43 1.7 42.1 92.8 1 1.6 145 232
13610 DN350 14 438 448 360 14.2 298 11.7 127 5.0 172 6.8 45 1.8 55.2 121.7 1 1.6 145 232
13611 DN400 16 489 511 410 16.1 350 13.8 140 5.5 197 7.8 52 2.0 75.3 166 1 1.6 145 232

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

EFFLUENT & PRECOAT VALVE

PNEUMATIC ACTUATED VALVE
F

ØE

All dimensions are in inches

Size Valve with
A B C D ØE F G H Model pneumatic
in
actuator
2 12 3/8 2 1/4 5 1/2 4 5/8 4 8 3/16 3 3/4 1 7/8 PN-75-DA Part # 14059
3 13 3/4 2 7/8 6 1/4 4 5/8 5 3/16 8 3/16 3 3/4 1 7/8 PN-75-DA Part # 13555
4 15 3 3/8 7 4 5/8 6 8 3/16 3 3/4 2 1/16 PN-75-DA Part # 13556
6 17 5/8 4 9/16 8 5 1/16 8 1/4 9 3/8 4 3/16 2 1/4 PN-85-DA Part # 13557
8 21 5 7/8 9 9/16 5 9/16 10 3/8 10 3/4 4 7/8 2 3/8 PN-100-DA Part # 13558
10 25 7/8 7 7/8 10 3/4 7 1/4 13 14 7/16 5 7/8 2 11/16 PN-125-DA Part # 13559
12 28 1/2 8 7/8 12 3/8 7 1/4 15 14 7/16 5 7/8 3 1/16 PN-125-DA Part # 13560
R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

PNEUMATIC ACTUATOR

General Features:

•
\
Compact, reliable design.
• Open-Closed adjustment stops.
• High visibility indicator.
• The top mounting pad is drilled and tapped to international NAMUR and ISO standards, providing for
quick and economical accessory mounting in conjunction with the NAMUR pinion shaft.
• Standard execution for temperatures from -4°F/-20°C to +180°F/+80°C with standard NBR70 seals

Materials Used:
Body: The Aluminum body extrusion is hard anodized to 45-50 microns to protect against wear and
corrosion while reducing piston friction to the absolute minimum.
End Caps: Epoxy coated die cast aluminum end caps provide maximum resistance against
potentially corrosive elements.
Pistons: The precisely balanced die cast aluminum pistons are fitted with high-quality rings and
guides, resulting in high ratios of output torque vs. input air pressure. The twin rack and
piston design creates a constant torque output on all models.
Piston Guides: Large contact areas and self-lubricating, highly durable materials provide high thrust
stability with minimum friction.
Pinion: The hardened steel pinion is precision ground and then nickel plated in order to reduce
friction, provide maximum wear resistance, and protect against corrosion under severe
conditions.
Pinion Seals: NBR-70 rubber pinion seals provide trouble free operation at standard temperature
ranges.
Heavy Duty Springs: True-rated spring sets create absolute confidence in all of the fail safe spring
return models. The high tensile steel springs are coated with zinc phosphate for corrosion resistance.
Springs can be safely and quickly modified into sets ranging from 40 pounds to 80 pounds. Full length
end cap bolts allow for easy and safe disassembly.

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

PNEUMATIC ACTUATOR

ACTUATOR VALVE MATRIX

Part # Model Valve Size
13553 PN‐75‐DA 2” – 4”
13720 PN‐85‐DA 6”
13721 PN‐100‐DA 8”
13722 PN‐125‐DA 10” – 12”

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

SYSTEM FILL VALVE

LEVER OPERATED

Part Numbers
Stainless Steel Nylon Coated
Size (in)
Disc Disc
2 518020RO37 516020R037
2 1/2 518025RO37 516025R037
3 518030RO37 516030R037
4 518040RO37 516040R037
5 N/A 516050R037
6 518060RO37 516060R037
8 518080RO37 516080R037

Size Dimensions with hand lever – All dimensions are in inches

in mm A B C D ØE F G H
2 50 11 5/8 2 1/4 5 1/2 3 7/8 4 1 3/4 8 11/16 1 3/4
2 1/2 65 12 1/2 2 5/8 6 3 7/8 4 13/16 1 3/4 8 11/16 1 7/8
3 80 13 2 7/8 6 1/4 3 7/8 5 1/2 1 3/4 8 11/16 1 7/8
4 100 14 1/4 3 3/8 7 3 7/8 6 1/4 1 3/4 12 5/8 2 1/16
5 125 15 5/8 4 1/4 7 1/2 3 7/8 7 7/16 1 3/4 12 5/8 2 1/4
6 150 16 7/16 4 9/16 8 3 7/8 8 7/16 1 3/4 12 5/8 2 1/4
8 200 19 5/16 5 7/8 9 9/16 3 7/8 10 5/8 1 3/4 16 9/16 2 3/8

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

DRAIN VALVE
BUTTERFLY VALVE WITH EXTENSION & LEVER

All Dimensions are in inches

DRAIN SIZE - in “A” PART NUMBER
3 19 7/8” 12517
4 37 7/8” 12518

DRAIN VALVE SP-18-48-176

DRAIN SIZE - in PART NUMBER

2 VLVBALLTRUE02

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

IN-LINE SIGHTGLASS
“A”

SCH. 40 PVC
CLEAR PIPE

SCH. 80 PVC
VAN STONE FLANGE

SIZE DIM “A”

PART NUMBER
in in
2 150NBSG002R1 17 9/16
3 150NBSG003R1 17 9/16
4 150NBSG004R1 17 11/16
6 150NBSG006R1 18
8 150NBSG008R1 18

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

GAUGE PANEL KIT

*LOOSE ITEMS
Gauge Panel
*PVC 1/4” Ball Valve to be
threaded into tapped hole
at the influent & effluent
fitting of face piping. See
FP drawing for location.

*1/4” MNPT X. 1/4” O.D.

Male tube Adapter
*1/4” O.D. Plastic Tubing
(Field cut length to suit)

(2) Panel Mounted

4 1/2” Dial Pressure Gauges

ONE REQ’D PER FILTER

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

RMF PROGRAMMER

SPECIFICATIONS
Fiberglass enclosure meets Nema ratings 3, 3r, 4, 4x, 12 and 13.
The controller provides total control of the system’s filtration and regeneration cycles, and provides
all necessary equipment interlocks and timing mechanisms to execute the filter program.
The controller is designed so that there is no day to day involvement with the operation of the filter system.
The controller PLC unit controls the functions of the bump cycle, pre coating of the filter elements, filter
pump start/stop interlock and open/close actuation of pneumatically operated valving.

 120V - Electrical requirements: 120VAC-1Ø-60Hz, 20 amp circuit protection

ONE REQ’D PER FILTER

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

FILTER REGULATOR

ONE REQ’D PER FILTER

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

VACUUM TRANSFER SYSTEM

VACUUM TRANSFER UNIT

BLOWER SUCTION FROM TANK

VACUUM TRANSFER VALVE

REMOTE RECEPTACLE LOCATION

1 1/2” PIPE

CUT VACUUM HOSE LENGTH TO SUIT

VACUUM DRAINAGE VALVE

PLUMB TO WASTE
INDEPENDENTLY

VACUUM HOSE TO MEDIA

NOTE!
FITTINGS AND HARDWARE AS SHOWN ARE SCH 80
PVC AND ARE SUPPLIED BY NEPTUNE BENSON

VACUUM HOSE VALVE

NOTE: Your Defender® Filter and most of its accessories are acceptable for unprotected installations exposed to
the elements. The vacuum transfer system and the compressor require supplementary covers to protect theses
units from the elements if installed in an unenclosed environment. Neptune Benson recommends a minimum
enclosure of an open shelter with a roof to provide protection from direct exposure to rain and snow.
R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

VACUUM TRANSFER SYSTEM (VTS)

Item: Vacuum Transfer Unit

Type: Utility
Tank Size: 5 gal.
Tank (Gal.): 5
Peak HP: 5.5
Amps AC: 9.2
Voltage: 120
Hz: 60
Static Pressure (In.): 57
CFM @ 2.5-In Orifice: 155
Tank Orifice (In.): 2.5
Tank Type: Plastic
Hose Dimensions: 1 1/2" x 18 ft.
Length (In.): 7.5
Width (In.): 16.75
Height (In.): 24.75
Filter: Cartridge Filter and Foam Sleeve
Replacement Filter: 4TB95
Power Cord Length (Ft.): 6
Agency Compliance: c-ULus

VTS Remote Receptacle: One UL approved Leviton 7599 GFCI receptacle

15Amp, 125V is included along with a Carlon weatherproof “T” box and an in-use Intermatic WP1010MC
lockable receptacle cover. The Vacuum Transfer Unit’s mounting bracket is factory connected to the
Defender® and pre-drilled to accept the remote receptacle assembly, which the VT unit plugs into. Onsite
field installations include homerun power feed to the GFCI receptacle and connection from the receptacle
to the Defender’s RMF panel. Remote receptacle configuration can be referenced on the FP-1 schematic
page. The assembly’s component specifications can be referenced in the subsequent submittal pages.

NOTE: Your Defender® Filter and most of its accessories are acceptable for unprotected installations exposed to
the elements. The vacuum transfer system and the compressor require supplementary covers to protect theses
units from the elements if installed in an unenclosed environment. Neptune Benson recommends a minimum
enclosure of an open shelter with a roof to provide protection from direct exposure to rain and snow

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

VACUUM TRANSFER SYSTEM (VTS)

Flexi-Guard Weatherproof
Die-Cast While-in-use Covers
• For Commercial Applications
• Heavy-duty die cast receptacle covers
• Complies with 2008 NEC Article 406.8(B)
• Offers same features as plastic models but are manufactured of heavy-duty cast
metal for severe applications such as schools and commercial buildings
• Patented Flexi-Guard inserts provide flexibility in field by selecting and installing
proper insert
• Two-gang model WP1030MC includes inserts for two-gang duplex and GFCI
requirements
• Cover includes lockable hasp that accepts up to .280 in. (7.112 mm) diameter shank
(lock not included)
• Max cord size for all covers: 2-16 gauge or 1-14 gauge

Cord Exit Port

Depth
Model Description Color Cord Diam. Length
(in.)
(in.) (in.)
Single-gang Vertical w/(WP17)
WP1010MC 3 1/8 Gray 0.75 0.75
Flexi-Guard Inserts

Single-gang Flexi-Guard WP17

Converts to toggle, 1 5/8, 1 3/4 or 2 1/8 in. diameter round.

Item: Weatherproof Receptacle Cover

Manufacturer: Intermatic
Model #: WP1010MC
Type: Single gang (Lockable)
Listing & Approval: UL (C&US) CSA

NOTE: Your Defender® Filter and most of its accessories are acceptable for unprotected installations exposed to
the elements. The vacuum transfer system and the compressor require supplementary covers to protect theses
units from the elements if installed in an unenclosed environment. Neptune Benson recommends a minimum
enclosure of an open shelter with a roof to provide protection from direct exposure to rain and snow

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129
SUBMITTAL Defender® Filter Automatic

VACUUM TRANSFER SYSTEM (VTS)

NOTE: Your Defender® Filter

and most of its accessories are
acceptable for unprotected
installations exposed to the
elements. The vacuum transfer
system and the compressor
require supplementary covers
to protect theses units from the
elements if installed in an
unenclosed environment.
Neptune Benson recommends
a minimum enclosure of an
open shelter with a roof to
provide protection from direct
exposure to rain and snow
AFØ ED

R 3/24/15

[Link] • 6 Jefferson Drive, Coventry, RI 02816

800.832.8002 • 401.821.2200 • Fax 401.821.7129