Avances en Soldadura para
Diseños Sanitarios
Richard E. Avery
Consultant to the
Nickel Institute
Mayo 17, 2004
Materiales posibles
• 304L& 316L – usados para la mayoría
de las aplicaciones
• 6% Molidbeno o super-austenitico acero
inoxidable
• Acero inoxidable Duplex
• Ni-Cr-Mo aleación de nickel
• Titanio puroComercial
Consideraciones de servicio
• 304L vs 316L – Mo (2-3%) in 316L
• mejora la resistencia a las picaduras
( pitting ) y grietas ( crevice )
• Susceptible a tensión y agrietamiento
sobre aproximadamente 150oF
• Duplex SS good resist. to SCC
• Higher chlorides, low pH may require 6%
Mo SS or Ni-Cr-Mo or titanium
Welding Processes Used
• GTAW or TIG
- manual
- orbital tube welding or automatic sheet
• GMAW – MIG, pulsed arc mode
• SMAW or covered electrode
• Laser welding for manu. of welded
tubing
Typical Sanitary Piping Systems
• Welded by gas tungsten arc welding
(TIG)
• Lines designed for CIP
• Inside of tube welds often not
accessible for grinding or inspection
In response to 3-A Request
• AWS D18.1
Specification for Welding Austenitic Stainless
Steel Tubing Systems in Sanitary (Hygienic)
Applications
• AWS D18.2
Guide to Weld Discoloration Levels on Inside
of Austenitic Stainless Steel Tube
Goals of D18.1 & D18.2
• Guidance of judging root welds of tubes
from OD appearance
• Guides for Procedure & Performance
Qualification, Preconstruction Weld
Samples
• Weld visual acceptance criteria
• Illustration of weld discoloration levels
AWS D18 Committee Work
• Members – equipment producers, users
& general interest groups
• 36 weld samples, many with ID defects
– examined on OD & ID by 3-A
inspectors
• Tube with varying levels of weld
discoloration
• Tube with varying discoloration levels
Welding Qualifications
• Welding Procedure Specification
(WPS) - for each type of weld
• Performance Qualification - to test
welder’s ability
• Preconstruction Weld Samples (PWS)
- 3 welds made by each welder to aid
in evaluating production welds
AWS D18.2 (1999): Heat Tint Levels on the Inside of
Welded 316L Austenitic Stainless Steel Tube
The Sample Numbers refer to the amount of oxygen in the purging gas:
No.1- 10ppm No.2 - 25ppm No.3 - 50ppm No.4 - 100ppm
No.5 - 200ppm No.6 - 500ppm No. 7 - 1000ppm No.8 - 5000ppm
No.9 -12500ppm No.10 -. 25000ppm
Note: welds on type 304L SS showed no significant difference in heat tint colour from
type 316L.
Heat Tint - Acceptance Limits
• Acceptable limits could vary with end
application service, D18.1 or D18.2
• Typically 5 and greater is unacceptable
• An acceptance level should be identified
by number rather than ppm of oxygen or
by workmanship standards for particular
contract
Factors Influencing Heat Tint
• Oxygen in backing gas increases HT
• Moisture in backing gas increases HT
• Contaminants such as hydrocarbons
increase discoloration
• Hydrogen in backing gas decreases HT
• Metal surface finish can affect
appearance
AWS D18.3 (Pending)
Specification for Welding Tanks, Vessels,
and Other Equipment in Sanitary
(Hygienic) Applications
• Welding Procedure & Performance Qual.
• Visual Examination Acceptance Criteria:
- reject defects; cracks, lack of penetration
etc
- acceptable & unacceptable weld profiles
prior to weld finishing
- annex – Weld & Adjacent Zone Finishes –
WF-1 (as-welded) ~ WF-8 (ground flush &
electropolished)
6% Mo or Superaustenitic SS
• Typically: 21 Cr, 24 Ni, 6 Mo, 0.2 N
• Areas for 6% Mo not handled by 316
- high chlorides ~ over 1000 ppm
- low pH environments
- where better pitting, crevice and stress
corrosion cracking resistance is
required
Welding 6% Mo SS
• Use over-alloyed filler metal – minimum
of 9% Mo Ni-Cr-Mo alloy
• GTAW welding procedures similar to
that for 304/316 except:
- preferably avoid autogenous welds to
avoid lower corrosion resistance
- somewhat lower heat input and
interpass temperature
What are Duplex Stainless
Steel?
Low-carbon stainless steels
containing approx. equal parts of
ferrite and austenite
from a balance of ferrite formers
(Cr,Mo) with austenite formers
(Ni,N) and heat treatment
Duplex Stainless Steel
Base Metal Upper Right, Weld Metal Bottom Left
Source:
The ESAB Group
Duplex SS – alloy 2205
• Typically: 22 Cr, 5 Ni, 3 Mo, O.15 N
• Structure is austenite islands in ferritic
matrix ~ 50/50 is ideal
• Higher strength – YS 2 to 3 times 316
- forming requires greater power
- more spring-back during forming
Duplex SS – (cont.)
• Stress corrosion cracking resistance
substantially better than 304/316
• Pitting & crevice cor. Resistance equal
or better than 316 in many media
• Good resistance to erosion & abrasion
DSS Welding - General
Requirements
• No preheat – 300F interpass typical
• Heat input 15 to 65 kJ/in.
• To avoid high ferrite in welds, filler
metals with higher nickel used ~ 2209
with 9% nickel
• Avoidance of arc strikes, oxidation,
grinding out of craters
GTAW Process - DSS
• Used for root passes and orbital welds
• Filler essential for ferrite-austenite
balance
• Ar + 20-40% He + up to 2.5% N2 to
counter N loss from weld - no hydrogen
• Backing gas to maintain weld N content
Duplex SS - Welding
• To avoid high ferrite in welds, filler
metals with higher nickel used ~ 2209
with 9% Ni
• Avoid loosing N in weld – N backing
common
• Heat input 15 to 65 kJ/in
• Interpass temperature 300F typical
Nickel Alloys & Titanium
• Selectively used for their high corrosion
resistant properties
• Ni-Cr-Mo alloys – weldability comparable to
austenitic SS
• Commercially pure titanium – readily welded
- extra care to prevent contamination from
atmosphere (oxygen, nitrogen)
Summary – Welding for Food
Industry
• Technology well established for making
structurally sound welds
• Greatest challenge is hygienic surface
considerations, i.e.
- welds free from surface defects
- surface finishes comparable to base metal
- control weld discoloration to levels
acceptable for end application
