MA5600> enable MA5600 # config MA5600 (config) MA5600 (config) MA5600 (config) MA5600 (config) MA5600 (config)

# # # # #

time 2008-06-11 11:00:00 -> date & local time auto-configuration enabled backup period auto-configuration backup period 1 time interval 01:00 auto-enable data backup period auto-backup interval data period 1 time 00:00

Step Precaution! MA5600 (config) # protect MA5600 (config-protect) # protect first-group 0/8/0 eth 0/7/0 second workmodepor tstate MA5600 (config-protect) # quit MA5600 (config) # sysname huawei Step 1 Set the IP address of the inband NMS port (GE port). Create an NMS VLAN huawei (config) # vlan 10 standard Add the upstream port to the VLAN huawei (config) # vlan 10 port 0 / 7 0 huawei (config) # vlan 10 port 0 / 7 1 / / for 2Enter frame subtend to the VLAN interface mode huawei (config) # interface vlanif 10 Set the IP address of the VLAN interface huawei (config-if-vlanif10) # ip address [ip_equipment]255.255.255.0 huawei (config-if-vlanif10) # quit Step 2 Add a route. huawei (config) # ip route-static 0.0.0.0 0.0.0.0 [ip_gateway] Step 3 huawei huawei huawei Set the SNMP parameters. (config) # snmp-agent sys-info version all (config) # snmp-agent community read public (config) # snmp-agent community write private

Step 4 Enable sending traps. huawei (config) # snmp-agent trap enable standard Step 5 Set the IP address of the target host for traps. huawei (config) # snmp-agent target-host trap address [nms_server_ip] securityna me private Step 6 Set the IP address of the inband NMS as the source address for sending tr aps. huawei (config) # snmp-agent trap source vlanif 10 Step 7 Save the data. huawei (config) # save Configure ADSL Step 1 Registering Adee MA5600 board to SCUB huawei (config) # display board 0 if the board still in "auto_find" state, please run the command as below; huawei (config) # board confirm 0 Step 2 Create smart VLAN for ADSL huawei (config) # vlan 340 smart

huawei (config) # vlan 341 smart / / for subtend to frame 2 Add the upstream port to the VLAN huawei (config) # vlan 340 port 0 / 7 0 huawei (config) # vlan 341 port 0 / 7 0 / / for subtend to frame 2 huawei (config) # vlan 341 port 0 / 7 1 / / for subtend to frame 2 Enter the VLAN interface mode Step 3 Configuring the QoS For Downstream huawei (config) # traffic table index 7 priority 384 ip 0 car-policy priority ta g-In-Package For Upstream huawei (config) # traffic table index 8 priority 64 ip 0 car-policy priority tag -In-Package huawei (config) # display traffic-index table from 0 Step 4 Configuring the port service bundle from the GE huawei (config) # multi-service-port vlan 340 port 0 / encap pppoe cttr rx-7 tx-cttr 8 / / For slot board 0 huawei (config) # multi-service-port vlan 340 port 0 / encap pppoe cttr rx-7 tx-cttr 8 / / For slot 1 board huawei (config) # multi-service-port vlan 340 port 0 / encap pppoe cttr rx-7 tx-cttr 8 / / For slot 2 board Ignore slot ... .. 7 & 8 (SCUB board) huawei (config) # multi-service-port vlan 340 port 0 / 15 0-63 VPI 0 VCI 35 user -encap pppoe cttr rx-7 tx-cttr 8 / / For slot board 15 Step 5 Configuring the ADSL line profile for the subscriber huawei (config) # adsl line-profile add 10 Command: adsl line-profile add 10 Start adding profile Press 'Q' to quit the current configuration and new configuration will be neglec ted > Do you want to name the profile (y / n) [n]: > Please choose the default value of type 0-adsl 1-ADSL2 + (0 ~ 1) [0]: 1 > Will you set the basic configuration for the modem? (y / n) [n]: y Note: Setting to these modes of G992.3 ~ 5 will lead that the adsl ports that ar e not support ADSL2 + not be activated ADSL transmission modes: > 0: All (5 ~ G992.1, T1.413) > 1: Full rate (G992.1/3/5 or T1.413) > 2: g.lite (G992.2 / 4) (ADSL over ISDN g.lite board does not support mode) > 3: T1.413 (ADSL over ISDN board does not support T1.413 mode) > 4: g.dmt (G992.1/3/5) > 5: g.hs (5 ~ G992.1, G992.5 is prior) > 6: G992.1 > 7: G992.2 > 8: G992.3 > 9: G992.4 > 10: G992.5 > 11: ADSL all (2 ~ G992.1, T1.413) > 12: ADSL & ADSL2 (G992.1 / 3 or T1.413) Please select (0 ~ 12) [0]: 0 > Trellis disable mode 0-1-enable (0 ~ 1) [1]: uplink to Adee board 0 0-63 VPI 0 VCI 35 user1 0-63 VPI 0 VCI 35 user2 0-63 VPI 0 VCI 35 user-

> Downstream channel bit swap 0-disable 1-enable (0 ~ 1) [0]: > Upstream channel bit swap 0-disable 1-enable (0 ~ 1) [0]: > Please select channel interleaved mode 0-1-fast (0 ~ 1) [0]: > Will you set interleaved delay? (y / n) [n]: > Please select the form of transmit rate adaptation in the downstream: > 0-adaptAtStartup fixed 1-2-adaptAtRuntime (0 ~ 2) [1]: > Will you set the SNR margin for a modem? (y / n) [n]: > Will you set the parameters for rate? (y / n) [n]: y > Minimum transmit rate in the downstream (32 ~ 32,000 Kbps) [32]: 32 -> not a 6 4 > Maximum transmit rate in the downstream (1024 ~ 32,000 Kbps) [24,544]: 384 > Minimum transmit rate in the upstream (32 ~ 6000 kbps) [32]: 32 > Maximum transmit rate in the upstream (32 ~ 6000 kbps) [1024]: 64 Add profile 10 successfully huawei huawei huawei huawei huawei huawei huawei huawei huawei huawei huawei huawei ... .. / / Ignore board 0 / 7 and 0 / 8; continue until the board 0 / 15 huawei huawei huawei huawei (config) # interface adsl 0 / 15 (config-if-adsl-0/15) # deactivate all (config-if-adsl-0/15) # activate all profile-index 10 (config-if-adsl-0/15) # quit (config) # interface adsl 0 / 0 (config-if-adsl-0 / 0) # deactivate all (config-if-adsl-0 / 0) # activate all profile-index 10 (config-if-adsl-0 / 0) # quit (config) # interface adsl 0 / 1 (config-if-adsl-0 / 1) # deactivate all (config-if-adsl-0 / 1) # activate all profile-index 10 (config-if-adsl-0 / 2) # quit (config) # interface adsl 0 / 2 (config-if-adsl-0 / 2) # deactivate all (config-if-adsl-0 / 2) # activate all profile-index 10 (config-if-adsl-0 / 2) # quit

Step 7 Configuring PITP P-mode huawei (config) # pitp enable pmode Step 8 Saving configuration huawei (config) # save