Ipc CM 770e

IPC-CM-770E
ASSOCIATION CONNECTING
ELECTRONICS INDUSTRIES
Guidelines for Printed

Board Component
Mounting
Developed by the Component Mounting Guidelines Task Group (5-21a)

of the Assembly & Joining Processes Committee (5-20) of IPC
Supersedes:
IPC-CM-770 - September 1968
IPC-CM-770A - March 1976
IPC-CM-770B - October 1980
IPC-CM-770C - March 1987
IPC-CM-770D - January 1996
Users of this publication are encouraged to participate in the

development of future revisions.
Contact:
IPC
2215 Sanders Road
Northbrook, Illinois
60062-6135
Tel 847 509.9700
Fax 847 509.9798
January 2004
IPC-CM-770E
Table of Contents
1
1.1
1.2
3.4.3
Storage .............................................................. 22
3.5
3.5.1
Material Movement Systems ............................ 23

Transporters ...................................................... 23
1
1
1
2
2
3.5.2
Racks and Carriers ........................................... 23
SCOPE ...................................................................... 1
1.2.1
1.2.2
1.2.3
1.2.4
Purpose ................................................................
Classification of Board Types and
Assemblies ..........................................................
Performance Classes ...........................................
Producibility Levels ............................................
Product Types .....................................................
Printed Circuit Board Assembly Types .............
1.3
1.4
1.5
Order of Precedence ........................................... 3

Presentation ......................................................... 3
Terms and Definitions ........................................ 3
APPLICABLE DOCUMENTS ................................... 8
2.1
IPC ...................................................................... 9
2.2
Joint Industry Standards ................................... 10
2.3
Electronic Industries Association ..................... 10
2.4
EOS/ESD Association Documents ................... 10
2.5
JEDEC .............................................................. 10
GENERAL GUIDELINES ........................................ 10
3.1
Design Options and Considerations ................. 10
3.1.1
Leadless Component Terminations .................. 11
3.1.2
Leaded Component Terminations ..................... 11
3.1.3
Spacing .............................................................. 11
3.1.4
Part Type ........................................................... 11
3.2
Assembly Considerations ................................. 12
3.2.1
Component Preparation .................................... 12
3.2.2
Lead Forming ................................................... 12
3.2.3
Component Placement ...................................... 13
3.2.4
Mixed Assemblies ............................................ 13
3.2.5
Component Securing ........................................ 15
3.3
Materials ........................................................... 16
3.3.1
Solder ................................................................ 16
3.3.2
Flux ................................................................... 16
3.3.3
Cleaning Agent ................................................. 17
3.3.4
Adhesive ........................................................... 17
3.3.5
Components ...................................................... 17
3.3.6
COMPONENT GUIDELINES .................................. 23
4.1
4.1.1
Component Characterization and Classes ........ 23

Axial-Leaded Components ............................... 23
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
Radial-Leaded Components .............................

Chip Components .............................................
Small Outline Components (SOs) ....................
Multiple-Ribbon-Lead Components .................
Chip Carriers ....................................................
Unpackaged Semiconductors ...........................
4.1.8
4.1.9
Tape Automated Bonding (TAB) ..................... 26

Area Array Components ................................... 26
4.1.10
4.1.11
4.1.12
Connectors ........................................................
Sockets ..............................................................
Electromechanical and Interconnect
Components ......................................................
Component Packaging/Delivery Systems ........
Lead/Termination Finishes ...............................
4.2
4.3
5
23
23
26
26
26
26
26
26
26
27
27
PACKAGING AND INTERCONNECTING

(PRINTED BOARD) STRUCTURES ...................... 27
5.1
5.1.1
5.1.2
5.1.3
Printed Board Characterization and Classes ....

Rigid Laminate Boards ....................................
Flexible Laminate Boards ................................
Metal-Core Boards ...........................................
5.2
5.2.1
Supporting-Plane Printed Board Structures ..... 28

Printed Board Bonded to Support Plane
(Metal or Nonmetal) ......................................... 28
5.2.2
5.3
Sequentially-Processed Structures with

Metal Support Plane .........................................
Discrete-Wire Structures with Metal
Support Plane ....................................................
Flexible Printed Board with Metal
Support Plane ....................................................
Constraining Core Printed Board Structures ...
Printed Boards .................................................. 17
5.3.1
Porcelainized-Metal (Metal Core) Structures .. 30
3.3.7
Board & Lead Finishes .................................... 18
5.3.2
3.3.8
Solderability ...................................................... 18
Printed Board with Constraining (Not

Electrically Functioning) Core ......................... 31
3.3.9
Coating .............................................................. 18
5.3.3
Printed Boards with Electrically-Functional

Constraining Cores ........................................... 31
3.4
Handling and Storage ....................................... 19
5.3.4
Printed Board with Constraining Core ............ 31
3.4.1
EOS/ESD .......................................................... 19
5.4
3.4.2
Moisture Sensitivity .......................................... 22
Other Mounting Structure Materials and

Considerations .................................................. 31
5.2.3
5.2.4
27
27
27
28
29
29
30
30
iii
IPC-CM-770E
5.4.1
5.4.2
5.4.3
5.4.4
6
Heat Sinks .........................................................

Spacers ..............................................................
Component-Lead Spreaders .............................
Thermally Conductive Insulators .....................
January 2004
31
33
33
34
ASSEMBLY DESIGN CYCLE ................................ 34
7.5.1
Solder Pastes and Adhesives ............................ 44
7.5.2
Solder Performs ................................................ 44

INTERCONNECT TECHNOLOGY ......................... 44
8.1
8.1.1
Component Spacing .......................................... 44

Component Considerations .............................. 44
8.1.2
8.1.3
8.1.4
8.2
8.3
8.4
Wave Solder Component Orientation ..............

Component Placement ......................................
Grid-Based Component Positioning ................
Single and Double-Sided Board Assembly .....
Component Standoff Height for Cleaning .......
Fiducial Marks ..................................................
8.4.1
8.4.2
Global Fiducials ................................................ 46

Local Fiducials ................................................. 46
Size and Shape of Fiducial ..............................
Conductors ........................................................
Conductor Width and Spacing .........................
Via Guidelines ..................................................
Drilled Via Holes ..............................................
6.1
6.1.1
Types of Assembly Operations ........................ 34

Inline Machines ................................................ 34
6.1.2
6.1.3
6.2
6.2.1
6.2.2
6.3
Sequential Machines .........................................

Mass Placement Machines ...............................
Soldering Operations ........................................
Manual Soldering Tools and Processes ...........
Automated Soldering Processes .......................
Assembly Sequence ..........................................
6.3.1
6.3.2
Inspect Before Assembly .................................. 37

Substrate Preparation ........................................ 37
6.3.3
Component Preparation (Tinning/Solder

Dipping) ............................................................ 37
Assembly Process Sequence ............................ 37
8.4.3
8.5
8.5.1
8.6
8.6.1
Mass Attachment Properties ............................. 37

Machine Soldering Processes ........................... 37
Environment (Nitrogen) ................................... 39
8.6.2
8.6.3
8.7
Vias and Land Pattern Separation .................... 48

Vias Under Components .................................. 48
Standard Fabrication Allowances ..................... 48
Controlled Atmosphere Soldering .................... 39
8.7.1
8.7.2
8.7.3
Manufacturing Characteristics .......................... 48

Conductor Width and Spacing Tolerances ....... 49
Conductive Pattern Feature Location
Tolerance ........................................................... 49
8.8
Board Size and Panelization ............................ 49
8.8.1
Panel Format ..................................................... 49
8.8.2
Panel Construction ............................................ 50
6.3.4
6.4
6.4.1
6.5
6.5.1
7
34
34
34
34
35
37
PLACEMENT GUIDELINES ................................... 39
44
44
45
45
45
46
47
47
47
47
47
7.1
Placement Technology ...................................... 39
7.1.1
Placement .......................................................... 39
7.1.2
Process Identification ........................................ 39
7.2
Design Checks .................................................. 41
7.2.1
Design Checks for All Assembly Types .......... 42
7.2.2
Design Checks for Surface Mounted

Assemblies ........................................................ 42
7.2.3
Design Checks for Mixed Technology

Assemblies Involving Auto-Placement
and Auto-Insertion ............................................ 43
9.1
Axial-Leaded Discrete Components ................ 52
9.1.1
Packaging Axial Leaded Discrete

Component ........................................................ 52
7.3
Specification and Procurement of

Components ...................................................... 43
9.2
Radial-Leaded Discrete Components ............... 53
9.2.1
7.3.1
Part Type Description ....................................... 53
Product Processes and Applications ................ 43
9.2.2
7.3.2
Component Package Style ................................ 43
Packaging Radial Leaded Discrete

Components ...................................................... 53
7.3.3
Component Transit Packaging ......................... 43
9.3
Multiple-Radial-Lead Components .................. 54
7.3.4
Date of Manufacture and Solderable

Coating Thickness ............................................ 43
9.3.1
Transistor Outline (TO) Cans .......................... 54
9.3.2
7.4
Specification and Procurement of

Printed Boards .................................................. 43
Multiple-Lead Variable Resistors ..................... 54
9.4
Inline Packages ................................................. 54
7.4.1
Specifying Printed Boards ................................ 43
9.4.1
Dual-Inline Packages ........................................ 54
7.4.2
Notifying Assemblers and Their Suppliers ...... 43
9.4.2
Single-Inline Packages ..................................... 54
7.4.3
Suitability for High Assembly Yield ............... 43
9.5
Ribbon-Lead Components ................................ 55
7.5
Specifications and Procurement of Process

Materials ........................................................... 44
9.5.1
Flatpack ............................................................. 55
9.6
Pin Grid Array Components ............................ 56
iv
COMPONENT CHARACTERISTICS
THROUGH-HOLE ................................................... 52
January 2004
IPC-CM-770E
9.7
9.8
Through-Hole Mount Connectors .................... 57

Through-Hole Sockets ...................................... 58
10
MOUNTING STRUCTURE REQUIREMENTS

THROUGH-HOLE ................................................. 59
11.3.2
Radial Leaded Discrete Components ............... 75
11.3.3
11.3.4
Multiple Radial Lead Component .................... 76

Hermetically-Sealed Components .................... 77
Rectangular-Bodied Components .....................
Metal Power Packages .....................................
Mixed Technology ............................................
Axial Leaded Discrete Components ................
Radial Leaded Discrete Components ...............
10.1
10.1.1
Printed Board Characterization and Types ...... 59

Lead/Hole Ratio ................................................ 59
10.1.2
10.1.3
10.1.4
59
59
11.3.5
11.3.6
11.4
11.4.1
11.4.2
59
11.4.3
11.4.4
Inline Leaded Components .............................. 77

59
60
60
11.5
11.5.1
11.5.2
11.5.3
11.5.4
11.6
11.6.1
11.6.2
11.6.3
Manual Techniques ...........................................

Axial and Radial Discrete Components ..........
Dual-Inline Package Gripping Tools ...............
Multiple Radial Leaded Discrete
Components ......................................................
Inline Leaded Components ..............................
Automated Techniques .....................................
Axial Leaded Discrete Components ................
Radial Leaded Discrete Components ...............
Multiple Radial Lead Components ..................
11.6.4
Inline Leaded Components .............................. 80
Unsupported Holes ...........................................

Supported Holes ...............................................
Axial and Radial Lead Component
Mounting ...........................................................
10.1.5 Multiple Radial Lead Component
Land Patterns ....................................................
10.1.6 Dual-Inline Package (DIP) Land Patterns .......
10.1.7 Land Patterns for Ribbon Lead Component ..
10.1.8 Land Patterns for Pin Grid Array
Component ........................................................
10.1.9 Land Patterns for Through Hole Mount
Connectors ........................................................
10.1.10 Land Patterns for Through Hole Mounted
Sockets ..............................................................
11
60
61
61
ASSEMBLY SEQUENCE THROUGH-HOLE ....... 61
11.1
11.1.1
11.1.2
11.1.3
Process Steps ....................................................

Sequence ...........................................................
Attachment Issues .............................................
Assembly Process Methods ..............................
61
61
61
61
11.1.4
11.1.5
11.1.6
11.1.7
Lead Termination after Assembly ....................

Preformed Leads ...............................................
Component Retention .......................................
Lead Cutting .....................................................
63
64
65
66
11.1.8
11.1.9
11.1.10
11.1.11
11.1.12
Axial Leaded Component ................................

Radial Leaded Discrete Component ................
Mechanical Securing ........................................
Inline Leads ......................................................
67
67
69
69
12
77
77
77
77
77
78
78
78
78
78
78
78
79
79
SURFACE MOUNT ............................................... 80
12.1
12.1.1
12.2
12.2.1
Characterization and Classes ............................

Part Type Descriptions .....................................
Component Procurement ..................................
Packaging ..........................................................
80
80
84
84
12.2.2
12.3
12.3.1
12.3.2
Delivery System ...............................................

Handling and Storage .......................................
ESD Protection .................................................
Moisture ............................................................
86
86
86
86
12.4
12.4.1
Chip Resistors ................................................... 87

Basic Construction ............................................ 87
11.1.13 Through Hole Mounted Connector .................. 72
12.4.2
Termination Materials ....................................... 87
11.2
Component Placement ...................................... 72
12.4.3
Marking ............................................................. 87
11.2.1
Straight Through Leads .................................... 72
12.5
Chip Capacitors ................................................ 87
11.2.2
Clinched Leads ................................................. 73
12.5.1
11.2.3
Lead Spacing .................................................... 73
12.5.2
11.2.4
Component Body .............................................. 73
12.5.3
Marking ............................................................. 88
11.2.5
Hardware Clearance ......................................... 73
12.6
Inductors ........................................................... 88
11.2.6
Radial Leaded Discrete Components ............... 74
12.6.1
11.2.7
Plastic Power Transistors ................................. 74
12.6.2
11.2.8
Electrical Insulators and Thermal

Conductors ........................................................ 75
12.6.3
Marking ............................................................. 89
12.7
Tantalum Capacitors ......................................... 89
Vertical Mounting ............................................. 75
12.7.1
Axial Leaded Discrete Components ................ 75
12.7.2
11.3
11.3.1
IPC-CM-770E
January 2004
12.7.3
12.8
12.8.1
12.8.2
Marking .............................................................
Metal Electrode Face (MELF) Components ...
Basic Construction ............................................
Termination Materials .......................................
90
90
90
90
12.8.3
12.9
12.9.1
12.9.2
12.9.3
12.10
12.10.1
Marking .............................................................
SOT 23 ..............................................................
Marking .............................................................
SOT 89 ..............................................................
90
90
90
90
90
90
90
12.10.2 Termination Materials ....................................... 91

12.10.3 Marking ............................................................. 91
12.11
12.11.1
12.11.2
12.11.3
12.12
SOD 123 ...........................................................

Marking .............................................................
SOT 143 ............................................................
91
91
91
91
91
12.12.1 Basic Construction ............................................ 91

12.12.2 Termination Materials ....................................... 91
12.12.3 Marking ............................................................. 91
12.13
12.13.1
12.13.2
12.13.3
SOT 223 ............................................................

Marking .............................................................
91
91
91
91
12.14
12.14.1
12.14.2
12.14.3
TO 252/TO 268 ................................................

Marking .............................................................
91
91
91
91
12.15
12.15.1
12.15.2
12.15.3
12.16
SOIC .................................................................
Pin Numbering ..................................................
SOP ...................................................................
91
92
92
92
92
12.16.1
12.16.2
12.16.3
12.17
12.17.1
12.17.2
12.17.3
12.18

Marking .............................................................
SOJ ....................................................................
Marking .............................................................
92
92
92
92
92
92
92
PLCC (Square) ................................................. 92
12.19.1 Premolded Plastic Chip Carriers ...................... 93

12.19.2
12.19.3
12.20
12.20.1
12.20.2
12.20.3
13
vi
PLCC (Rectangular) ......................................... 93
MOUNTING STRUCTURE GUIDELINES

SURFACE MOUNT ............................................... 94
Printed Board Characterization and Types ...... 94

Organic Rigid, Organic Flex and Rigid-Flex .. 94
13.3
13.4
13.4.1
Land Patterns .................................................... 94

Tolerance Analysis ............................................ 95
Land pattern Configurations for Small
Outline Packages .............................................. 95
13.4.2
13.4.3
Land patterns for DIPs and SIPs ..................... 97

Chip Carrier Land Patterns .............................. 97
13.4.4
Land Patterns for Surface Mount

Connectors ........................................................ 97
13.4.5
13.5
13.5.1
Land Patterns for Surface Mount Sockets ....... 97

Alternative Printed Board Structures ............... 97
Supporting-Plane Printed Board ...................... 97
13.5.2
13.6
13.6.1
13.7
High-Density Printed Board Technology .........

Surface Preparation ..........................................
Temporary Masking Guidelines .......................
Gold on Printed Board Surface Mount
Lands .................................................................
Gold Thickness .................................................
Printed Board Condition ..................................
13.7.1
13.8
98
98
98
98
98
98
SURFACE MOUNT ............................................... 98
14
14.1
14.1.1
Assembly Hierarchy ......................................... 98

Sequence ........................................................... 98
14.1.2
14.1.3
14.1.4
14.1.5
14.2
14.2.1
14.3
Attachment Issues ............................................. 98

Lead/Land Configuration after Assembly ...... 105
Placement ........................................................ 105
Mixed Technology .......................................... 105
Manual Techniques ......................................... 106
Manual Assembly ........................................... 106
Automated Assembly Techniques .................. 106
14.3.1
Placement ........................................................ 107
14.3.2
Automated Assembly of Surface Mount

Connectors ...................................................... 107
14.3.3
Automated Assembly of Surface Mount

Sockets ............................................................ 108
15
12.18.3 Marking ............................................................. 93

12.19
93
93
94
94
94
94
13.1
13.2
12.18.l Premolded Plastic Chip Carriers ...................... 93

12.18.2 Post-Molded Plastic Chip Carriers .................. 93
Post-Molded Plastic Chip Carriers ..................

Marking .............................................................
LCC ...................................................................
Marking .............................................................
15.1
HIGH PIN COUNT AREA ARRAY ...................... 108
Component Definition .................................... 108
January 2004
15.1.1
15.1.2
15.1.3
15.2
IPC-CM-770E
18.2.3
Nonmelting Bumps ......................................... 115
18.2.4
18.3
18.3.1
Polymeric/Conductive Adhesive Bumps ........

Component Design for Circuit Boards ..........
Design Considerations (repeated
information) ....................................................
Chip Size Standardization ..............................
Bump Site Standards ......................................
Peripheral Lead Standards ..............................
Package Size Standards ..................................
I/O Capability .................................................
15.2.1
15.2.2
15.2.3
Body Size ........................................................ 108

Ball Size Relationships .................................. 108
Coplanarity ...................................................... 108
Component Packaging Style
Considerations ............................................... 109
Plastic Ball Grid Arrays (PBGA) .................. 109
Ceramic Ball Grid Arrays (CBGA) ............... 110
Ceramic Column Grid Arrays (CCGA) ......... 111
15.2.4
15.3
Tape Ball Grid Arrays (TBGA) ..................... 111

BGA Connectors ............................................. 112
18.3.2
18.3.3
18.3.4
18.3.5
18.3.6
15.3.1
Assembly Considerations for BGA

Connectors ...................................................... 112
18.3.7
18.3.8
15.3.2
15.4
15.5
Material Considerations for BGA

Connectors ...................................................... 112
Components Package Drawings ..................... 112
Component Procurement ................................ 112
Alpha Particle Emissions (Soft Errors) ......... 118

Substrate Structure Standard Grid
Evolution ......................................................... 119
15.5.1
15.5.2
15.6
Shipping Media ESD ...................................... 112

Delivery System ............................................. 112
Handling and Storage ..................................... 112
15.6.1
15.6.2
ESD Protection ............................................... 112

Moisture .......................................................... 112
18.3.9
18.3.10
18.3.11
18.3.12
18.3.13
18.3.14
18.3.15
18.3.16
Footprint Design .............................................

Design Guide Checklist ..................................
Die Design Shrinks ........................................
I/O Drivers on the Periphery .........................
Isolating Sensitive I/Os ..................................
Printed Board Land Pattern Design ...............
High Frequency Performance ........................
Thermal Design ..............................................
120
120
121
121
122
122
122
123
18.4
18.4.1
18.4.2
18.4.3
18.4.4
18.4.5
Handling, Shipping and Storage ....................

Handling Systems ...........................................
Storage Atmosphere ........................................
ESD Protection ...............................................
Types of Carrier Packaging for Shipping ......
Storage System and Length of Storage .........
124
124
125
125
125
125
18.5
18.5.1
Mechanical Properties .................................... 125

Interconnect Joint Dimensions ....................... 126
18.5.2
Solderability of Bumps Not Wetting

or Partial Wetting to Substrate is a
Reliability Concern ......................................... 126
16
16.1
MOUNTING STRUCTURE REQUIREMENTS

HIGH PIN COUNT AREA ARRAY ...................... 113
16.2
16.3
Characterization and Classes Interconnecting Structures (Printed Boards) .. 113

Standardization ............................................... 113
Ball Pitch ........................................................ 113
16.4
16.5
16.6
Future Ball Conditions ................................... 113

Land Approximation ....................................... 113
Physical Conditions ........................................ 114
17
ASSEMBLY HIERARCHY HIGH PIN COUNT

AREA ARRAY ..................................................... 114
115
117
117
117
118
118
118
118
17.1
Process Steps .................................................. 114
18.6
Electrical Issues .............................................. 126
17.1.1
Sequence ......................................................... 114
18.6.1
Wafer Test/Sorting Inked Die ........................ 127
17.2
Process Step Analysis ..................................... 114
18.6.2
17.3
Attachment Issues ........................................... 114
Room Temperature Testing of Wafer

vs. Testing Wafers over Temperature
and Costs ........................................................ 127
17.4
Reflow ............................................................. 115
18.7
Marking ........................................................... 127
17.5
Preclad ............................................................. 115
18.8
Physical Conditions ........................................ 127
18.8.1
Workmanship .................................................. 127
18
COMPONENT CHARACTERISTICS FLIP

CHIP DIRECT CHIP ATTACH ............................ 115
19
MOUNTING STRUCTURE GUIDELINES

FLIP CHIP DIRECT CHIP ATTACH (Refer
to General Guidelines Section) ....................... 127
20
ASSEMBLY HIERARCHY FLIP CHIP

DIRECT CHIP ATTACH ...................................... 127
18.1
Types of Flip Chip Joints ............................... 115
18.1.1
Solder Bumps ................................................. 115
18.1.2
Nonsolder Type Bumps .................................. 115
18.2
Characterization and Classes of Flip

Chip Joints ...................................................... 115
20.1
Process Steps .................................................. 127
18.2.1
Meltable Solder Joints .................................... 115
20.2
18.2.2
Partially Meltable Bumps ............................... 115
Manual Techniques for Semiautomated

Pick and Place ................................................ 127
vii
IPC-CM-770E
January 2004
20.2.1
20.3
20.3.1
20.3.2
Dexterity .........................................................
Automated Techniques ...................................
Types of Equipment .......................................
Precision ..........................................................
128
128
128
128
23.2.1
Magnification Aids for Examining Printed

Board Assemblies ........................................... 135
23.3
Process Control ............................................... 135
23.3.1
Corrective Action Limits ................................ 135
20.4
20.5
20.5.1
20.5.2
20.5.3
20.5.4
Single Point Attachment .................................

Mass Attachment Properties ...........................
Convection Oven Solder Reflow ...................
Vapor Phase Solder Reflow ............................
Infrared Solder Reflow ...................................
128
128
128
128
128
23.3.2
Process Control Details .................................. 135
23.3.3
Defect Reduction ............................................ 136
23.3.4
Variance Reduction ......................................... 136
23.4
Process Verification Inspection ...................... 136
23.4.1
Workmanship .................................................. 136
20.5.5
Nitrogen Reflow Atmosphere ......................... 128
23.4.2
General Modification/Repair .......................... 136
23.4.3
Destructive Testing ......................................... 136
23.4.4
Mild Burn-In (24 hr per assembly) ............... 136
21
Profile Analysis ............................................... 128
CLEANING .......................................................... 128
21.1
General Considerations .................................. 128
21.1.2
Selection of Cleaning Materials ..................... 129
21.1.3
Frequency of Cleaning ................................... 129
21.1.4
Ultrasonic Agitation ........................................ 129
21.2
Cleanliness Assessment .................................. 129
21.2.1
Flux Residues ................................................. 129
21.2.2
Visual Inspection ............................................ 129
21.2.3
Solvent Extract Conductivity Measurement .. 129
21.3
22
24
24.1
25
PERFORMANCE/RELIABILITY
EVALUATIONS .................................................... 136
Relationships to Test and Quality

Assurance ........................................................ 136
REPAIR/REWORK .............................................. 137
25.1
Reuse of Components .................................... 137
25.2
Heat Sinking Effects ....................................... 137
Post-Soldering Cleaning ................................. 129
25.3
Dependence on Printed Board Material

Type ................................................................ 138
ELECTRICAL TEST CONSIDERATIONS .......... 130
25.4
Dependence on Copper Land and

Conductor Layout ........................................... 138
22.1
Five Types of Testing ..................................... 130
22.1.1
Bare-Board Test .............................................. 130
25.5
Selection of Suitable Rework Equipment ...... 138
22.1.2
Assembled Board Test .................................... 130
25.6
22.2
Nodal Access .................................................. 130
Dependence on Assembly Structure and

Soldering Processes ........................................ 138
22.2.1
Test Philosophy .............................................. 131
26
22.2.2
Test Strategy for Bare Boards ........................ 131
26.1
Conformal Coating ......................................... 138
22.3
Full Nodal Access for Assembled Board ...... 131
26.1.1
Application ...................................................... 138
22.3.1
In-circuit Test Accommodation ...................... 131
26.1.2
Performance Guidelines ................................. 139
22.4
Limited Nodal Access .................................... 132
26.1.3
22.5
No Nodal Access ............................................ 132
Rework of Conformal Coating ...................... 139
22.6
Clam-Shell Fixtures Impact ........................... 132
26.1.4
Conformal Coating Inspection ....................... 139
22.7
Printed Board Test Characteristics ................. 132
26.2
Encapsulation .................................................. 139
22.7.1
Test Land Pattern Spacing ............................. 132
26.2.1
Application ...................................................... 139
22.7.2
Test Land Size and Shape .............................. 132
26.2.2
Performance Guidelines ................................. 139
22.7.3
Design for Test Parameters ............................ 132
26.2.3
Rework of Encapsulant Material ................... 140
22.7.4
In-Circuit Test ................................................. 133
27
22.7.5
Functional Test ............................................... 134
27.1
Drawing Requirements ................................... 140
22.7.6
Test Probes and Probe Lands ......................... 134
27.2
Electronic Data Transfer ................................ 140
QUALITY ASSURANCE ..................................... 134
27.3
Specifications .................................................. 140
23.1
Relationship to Test/Inspection ...................... 134
27.4
23.1.1
Visual Inspection ............................................ 134
Printed Board Assembly Documentation

Process Flow ................................................... 140
23.2
Standard Magnification .................................. 135
27.5
Documentation for SMT ................................ 141
23
viii
COATING AND ENCAPSULATION ................... 138
DOCUMENTATION ............................................. 140
January 2004
IPC-CM-770E
Figures
Figure 7-4
Mixed Technology Assembly, Double-Sided:

Reflow and Immersion (See Table 6-1
THROUGH HOLE AND SURFACE MOUNT
MIX REFLOW AND IMMERSION) ............... 40
Figure 1-1
Type 1 Printed Board Assembly .................... 3
Figure 1-2
Type 2 Printed Board Assemblies .................. 4
Figure 1-3
Clinched Wire Through Connection ............... 6
Figure 7-5
Figure 3-1
Staggered Hole Pattern Mounting

MO Flatpack Outline Drawing (Only
Inches Shown) ............................................. 12
Mixed Technology Assembly, Double-Sided

Reflow and Manual ...................................... 41
Figure 7-6
Mixed Technology Assembly, Double-Sided,

Immersion Only ............................................ 41
Figure 3-2
Component Modifications for Surface

Mounting Applications .................................. 13
Figure 7-7
Panel Assembly Tooling Holes ..................... 41
Figure 7-8
Panel Assembly Tooling Holes ..................... 42
Figure 3-3
Modifying DIP for Surface Mounting ............ 13
Figure 8-1
Figure 3-4
Placement Machine Considerations ............ 13
Component Orientation for Wave-Solder

Applications .................................................. 45
Figure 3-5
Mixed Assemblies ........................................ 14
Figure 8-2
Alignment of Similar Components ............... 45
Figure 3-6
Clip-Mounted Component ............................ 15
Figure 8-3
Panel/Global Fiducials ................................. 46
Figure 8-4
Local and Global Fiducials ........................... 46
Figure 8-5
Fiducial Locations on a Printed Board ......... 46
Figure 8-6
Fiducial Clearance Requirements ................ 47
Figure 8-7
Surface Mounting Geometries ..................... 47
Figure 8-8
Land Pattern-to-Via Relationship ................. 48
Figure 8-9
Examples of Via Positioning Concepts ........ 49
Figure 8-10
Conductor Description .................................. 50
Figure 8-11
Routed Slots ................................................ 51
Figure 8-12
Typical Copper Glass Laminate Panel ........ 51
Figure 8-13
Conductor Clearance for V-Groove

Scoring ......................................................... 52
Figure 8-14
Breakaway (Routed Pattern) with Routed

Slots ............................................................. 52
Figure 9-1
Axial-Leaded Component ............................. 53
Figure 9-2
Taped Axial-Leaded Components ................ 53
Figure 9-3
Polarized Axial Lead Component (Typical

Polarity Markings) ........................................ 53
Figure 9-4
Rectangular Radial Lead Capacitors ........... 53
Figure 9-5
Disc Radial Lead Capacitors ....................... 54
Figure 9-6
Cast Radial Lead Capacitor ......................... 54
Figure 9-7
Radial-Leaded TO-3 Transistor Can ............ 54
Figure 9-8
Multiple-Lead Variable Resistor ................... 54
Figure 9-9
16-Lead Dip ................................................. 55
Figure 9-10
Single Inline Packages Component ............. 55

Flatpack Outline Drawing ............................. 56
Figure 3-7
Strap Securing ............................................. 16
Figure 3-8
Frequently Encountered EOS/ESD

Warning Labels ............................................ 20
Figure 3-9
Series Connected Wrist Strap ..................... 22
Figure 3-10
Parallel Connected Wrist Strap .................... 22
Figure 4-1
Through-the-Board Component Types ........ 24
Figure 4-2
Some Surface Mount Component Types ..... 25
Figure 5-1
Printed Board Bonded to Supporting

Plane ............................................................ 29
Figure 5-2
Sequentially Processed Structure with

Supporting Plane ......................................... 30
Figure 5-3
Discrete-Wire Structure with LowExpansion Metal Support Plane .................. 30
Figure 5-4
Flexible Printed Board with Metal Support

Plane ............................................................ 31
Figure 5-5
Printed Board with Supporting Plane (Not

Electrically-Functional Constraining Core) ... 32
Figure 5-6
Multilayer Printed Board Structure with

Copper-Clad Invar Power and Ground
Planes (Electrically-Functional Constraining
Cores) .......................................................... 32
Figure 5-7
Figure 5-8
Balanced Structure with Constraining Core

not at Neutral Axis ....................................... 32
Balanced Structure with Constraining Core
on Neutral Axis not at Neutral Axis .............. 32
Figure 5-9
Common Component Heat Sinks ................ 33
Figure 9-11
Figure 5-10
Typical Spacers ............................................ 33
Figure 9-12
Figure 5-11
Typical Ribbon Leaded Discrete Device

Outline Drawing (Flat Leads) ....................... 56
Can Mounting Spreader ............................... 33
Figure 9-13
Pin Grid Array .............................................. 57
Figure 5-12
Thermally Conductive Insulator ................... 34
Figure 9-14
Figure 7-1
Single-Sided Surface Mount Assembly,

Reflow Only (See Table 6-1 SURFACE
MOUNT SINGLE-SIDED A REFLOW
ONLY) ........................................................... 40
I/O Density Versus Lead Count (All

Dimensions in Inches) .................................. 57
Figure 9-15
Connector with Press Fit Contacts .............. 57
Figure 9-16
Surface Mount Clip Carrier Socket .............. 58
Figure 9-17
Section Through Socket Solder Contact ..... 58
Figure 10-1
Typical TO-100 Can Layout ......................... 59
Figure 10-2
Typical Mounting Pattern for 10-Lead

Cans with Clinched Leads ........................... 60
Figure 10-3
A Typical Dual-Inline Layout ........................ 60
Figure 10-4

(Flatpack Outline Drawing) .......................... 60
Figure 7-2
Figure 7-3
Single-Sided Surface Mount Assembly,

Immersion Only (See Table 6-1 SURFACE
MOUNT SINGLE-SIDED B IMMERSION
ONLY) ........................................................... 40
Mixed Technology Assembly, Double-Sided,
Reflow Only (See Table 6-1 SURFACE
MOUNT DOUBLE-SIDED REFLOW
ONLY) ........................................................... 40
ix
IPC-CM-770E
January 2004
Figure 11-1
Component Mounting Sequence ................. 62
Figure 11-43
Transistor Mounting (with Spacer) ............... 77
Figure 11-2
Thermal Shunt ............................................. 63
Figure 11-44
Figure 11-3
Termination Examples .................................. 64
Metal Power-Package Transistor Mounted

on Resilient Standoffs .................................. 77
Figure 11-4
Clinched Lead .............................................. 65
Figure 11-45
Dual-Inline Package Gripping Tools ............. 78
Figure 11-5
Clinch Patterns ............................................. 66
Figure 11-46
Transistor Assembly Tools ........................... 79
Figure 11-6
Offset Clinched Lead ................................... 66
Figure 11-47
Taping Specifications (only inches shown) .. 79
Figure 11-7
Semiclinched Lead ....................................... 66
Figure 11-48
DIP Clearances ............................................ 80
Figure 11-8
Bend Configuration ...................................... 67
Figure 11-49
DIP Layout in Rows and Columns ............... 80
Figure 11-9
Lead Diameter Versus Bend Radius ........... 68
Figure 11-50
DIP Slide Magazines .................................... 80
Figure 11-10
Stress Relief Examples ................................ 68
Figure 12-1
50-mil Center JEDEC Packages .................. 81
Figure 11-11
Simple-Offset Preformed Lead .................... 68
Figure 12-2
Features Common to 0.050 inch Center

Packages ..................................................... 82
Figure 11-12
Dimple Preformed Leads ............................. 68
Figure 12-3
Figure 11-13
Compound Preformed Leads ....................... 69
Criteria for Lead Attachment to Leadless

Type A to Make a Leaded Type B ............... 82
Figure 11-14
Combination Preformed Leads .................... 69
Figure 12-4
Double Row Plastic Chip Carrier ................. 83
Figure 11-15
Stress Relief Leads ...................................... 69
Figure 12-5
Figure 11-16
TO Can Lead Forming ................................. 69
Common Configurations of Rectangular

Resistors ...................................................... 84
Figure 11-17
Dimple Preformed Leads ............................. 69
Figure 12-6
Typical Rectangular Chip Capacitors ........... 84
Figure 11-18
Typical Mounting Pattern for 12-Lead

Cans with Clinched Leads Mounting ........... 70
Figure 12-7
Cylindrical/Rectangular Terminations ........... 85
Figure 12-8
A Chip Inductor ............................................ 85
Figure 11-19
Mechanically Secured Transistor ................. 70
Figure 12-9
Typical Surface Mount Inductor ................... 85
Figure 11-20
Single-Inline Component .............................. 70
Figure 12-10
Surface Mount Cermet Trimmer .................. 85
Figure 11-21
Lead Configuration (After Assembly) ........... 71
Figure 12-11
Figure 11-22
Resilient Spacer to Heat Sink Frame .......... 71
SO-16 Package Drawings Typical

Dimension .................................................... 86
Figure 11-23

(Flatpack Outline Drawing) .......................... 71
Figure 12-12
Typical SOT Packages (Refer to JEDEC

Publication 95 for dimension data.) ............. 87
Figure 11-24
Through-Hole Mounting (Flatpack Outline

Drawing) ....................................................... 71
Figure 12-13
Basic Chip Resistor Construction ................ 88
Figure 12-14
Chip Capacitor Construction ........................ 88
Figure 11-25
Through-Hole Board Mounting with

Unclinched Leads ........................................ 72
Figure 12-15
Inductor Construction ................................... 89
Figure 11-26
Through-Hole Mounting with Clinched

Leads and Circumscribing Land .................. 72
Figure 12-16
Tantalum Capacitor Construction ................. 89
Figure 11-27
Through-Hole Mounting with Offset Land .... 72
Figure 11-28
Components Mounted Over Conductors ..... 73
Figure 12-17b Break-Away Diagram of MELF

Components Construction Figure ................ 90
Figure 11-29
Uncoated Board Clearance .......................... 73
Figure 12-18
SOT 23 Construction ................................... 90
Figure 11-30
Component Alignment .................................. 74
Figure 12-19
SOT 89 Construction ................................... 91
Figure 11-31
Component Alignment .................................. 74
Figure 12-20
SOD 123 Construction ................................. 91
Figure 11-32
Component Misalignment ............................ 74
Figure 12-21
SOT 143 Construction ................................. 91
Figure 11-33
Component Misalignment Clearance ........... 74
Figure 12-22
SOT 223 Construction ................................. 91
Figure 11-34
Horizontal Mounting of Radial Leaded

Component ................................................... 75
Figure 12-23
TO 252 Construction .................................... 92
Figure 12-24
SOIC Construction ....................................... 92
Figure 11-35
Horizontal Mounting of Radial Leaded

Component with Heat Sink .......................... 75
Figure 12-25
SOPIC Construction ..................................... 92
Figure 12-26
PLCC (Square) ............................................ 93
Figure 12-27
PLCC (Rectangular) Construction ............... 93
Figure 13-1
Chip Component and Lands ........................ 94
Figure 13-2
Chip Component and Lands ........................ 97
Figure 11-36
Horizontal TO Mounting ............................... 75
Figure 11-37
Vertical Mounted Axial Lead Components ... 75
Figure 11-38
Vertical Mounted Radial-Lead

Components ................................................. 76
Figure 12-17a Metal Electrode Face Component ............... 90
Figure 11-39
Vertical Mounted Components Coating

Meniscus ...................................................... 76
Figure 13-3
Example of 68 I/O Land Pattern on

Printed Board Structure ............................... 97
Figure 11-40
Radial Components Mounting

(Unsupported Holes) .................................... 76
Figure 14-1
No Bridging .................................................. 99
Figure 14-2
Lead Forming for Surface Mounting ............ 99
Figure 14-3
Criteria for Lead Attachment to Leadless

Type A (Leaded Type B) ............................ 100
Figure 11-41
Straight-Through Lead, Unclinched Can ..... 76
Figure 11-42
Offset Lead Can Mounting ........................... 76
January 2004
IPC-CM-770E
Figure 14-4
SO-16 Package Drawings Typical

Dimension .................................................. 101
Figure 18-22
Appropriate Thermal Model for Thermal

Paste .......................................................... 125
Figure 14-5
Typical SOT Packages ............................... 101
Figure 18-23
Chip Underfill Example .............................. 125
Figure 14-6
Modifying DIP for Surface Mounting .......... 101
Figure 18-24
Figure 14-7
Gull-Wing Lead for SIP-Type Component . 102
Approximate Thermal Model for

Chip Underfill ............................................. 125
Figure 14-8
Surface Mount Connector .......................... 102
Figure 18-25
Recommended DCA Grid Pitch (250 m

Grid, 150 m Bumps) ............................... 126
Figure 14-9
D-Subminiature Surface Mount

Connector ................................................... 102
Figure 22-1
Test Via Grid Concepts .............................. 131
Figure 22-2
General Relationship Between Test

Contact Size and Test Probe Misses ......... 133
Figure 22-3
Test Probe Feature Distance from

Component ................................................. 133
Figure 14-10
Surface Mount Receptacle ......................... 102
Figure 14-11
Box-Contact Surface Mount Connector ..... 103
Figure 14-12
Leadless Grid Array Socket ....................... 103
Figure 14-13
Surface Mount Chip Carrier Socket ........... 103
Figure 23-1
Destructive Testing Coupons ..................... 137
Figure 14-14
High Speed Circuit Socket ......................... 104
Figure 27-1
Documentation Set Flow Characteristics ... 141
Figure 14-15
Screw Down Cover .................................... 104
Figure 14-16
Pressure Mounted Socket .......................... 104
Figure 14-17
Preferred Mounting Orientations ................ 107
Table 1-1
Interconnection Acronyms and Definitions ........ 5
Figure 15-1
Cross-Section of a Plastic Ball Grid

Array (PBGA) Package .............................. 110
Table 3-1
Typical Static Charge Sources ........................ 20
Figure 15-2
Cross-Section of a Ceramic Ball Grid

Array (CBGA) Package .............................. 111
Table 3-2
Typical Static Voltage Generation .................... 20
Table 3-3
Figure 15-3
Cross-Section of a Ceramic Column

Grid Array (CCGA) Package ...................... 111
Maximum Allowable Resistance and

Discharge Times for Static Safe Operations ... 21
Table 5-1a
Figure 15-4
Cross-Section of a Tape Ball Grid

Array (TBGA) Package ............................... 111
Packaging and Interconnecting Structure

Comparison ...................................................... 28
Table 5-1b

Comparison ...................................................... 28
Figure 15-5
BGA Connector .......................................... 112
Table 5-1c
Figure 18-1
Typical Meltable Solder Bump ................... 116

Comparison ...................................................... 29
Figure 18-2
Partially Meltable Solder Bump .................. 116
Table 5-1d
Figure 18-3
Nonmeltable Bump ..................................... 116

Comparison ...................................................... 29
Figure 18-4
Isotropic Adhesive Bump ............................ 116
Table 6-1
Figure 18-5
Flip Chip Connection .................................. 117
Through Hole and Surface Mount Assembly

Process Flow Comparison ............................... 38
Figure 18-6
Table 8-1
Mechanical and Electrical Connections ..... 117
Typical Conductor Width Tolerances ............... 50
Figure 18-7
Table 8-2
Joined Chip with Chip Underfill .................. 117
Recommended Feature Location Accuracy ..... 50
Figure 18-8
Interconnect Density (Peripheral Vs.

Area Array) ................................................. 118
Table 11-1
Lead Clinch Length .......................................... 66
Table 12-1
Figure 18-9
Alpha Particle Emission Track and

E/H Pairs .................................................... 119
JEDEC Ceramic Sizes

and Fine Pitch Terminal Count ........................ 83
Table 12-2
General Application Considerations ................. 88
Figure 18-10
Distortion of Depletion by Alpha Particles .. 119
Table 13-1
Figure 18-11
Standard Grid Structure ............................. 120
Tolerance Analysis
Elements for Chip Devices .............................. 95
Figure 18-12
Table 13-2
Bump Footprint Planning ........................... 120
Flat Ribbon L and Gull-wing

Leads (Greater than 0.625 mm Pitch) ............. 95
Figure 18-13
Alignment to Visual/Sensitive Chip

Structures ................................................... 121
Table 13-3
Round or Flattened (Coined) Leads ................ 96
Figure 18-14
Table 13-4
Design Shrink Footprint ............................. 121
J-Leads ............................................................ 96
Figure 18-15
Table 13-5
Signal and Power Distribution Position ...... 122
Rectangular or Square-End Components

(Ceramic Capacitors and Resistors) ................ 96
Figure 18-16
Nested I/O Footprints ................................. 122
Table 13-6
Figure 18-17
Printed Board Flip Chip or Grid Array

Land Patterns ............................................. 122
Rectangular or SquareEnd Components (Tantalum Capacitors) ......... 96
Table 13-7
Cylindrical End Cap Terminations .................... 96
Figure 18-18
MSMT Land Drawing and Dimensions

Patterns ...................................................... 122
Table 13-8
Bottom Only Terminations ................................ 96
Table 13-9
Figure 18-19
Thermal/Electrical Analogy ......................... 123
Leadless Chip Carrier With Castellated

Terminations ..................................................... 96
Figure 18-20
Bump Interconnect Equivalent Model ........ 124
Table 13-10 Butt Joints ........................................................ 96
Figure 18-21
Thermal Paste Example ............................. 124
Table 13-11 Inward Flat Ribbon L and Gull-Wing Leads .... 96
Tables
xi
IPC-CM-770E
Table 13-12 Flat Lug Leads ................................................. 96
Table 16-1
Ball Diameter Sizes ........................................ 113
Table 16-2
Future Ball Size Diameters ............................ 113
Table 16-3
Land Size Approximation ............................... 113
Table 16-4
Future Land Size Approximations .................. 114
Table 18-1
Alpha Particle Emissions

of Semiconductor Materials ........................... 119
Table 18-2
Design Rules for Substrates for Chip Scale

Technology ..................................................... 119
Table 18-3
Typical Thermal Resistance for Variable

Bump Options (Triple Layer Chip) ................. 124
Table 18-5
C4 Bump Diameter
and Minimum Pitch Options ........................... 126
Table 23-1
Inspection Magnification ................................ 135
Table 26-1
Coating Thickness ......................................... 139
xii
January 2004
January 2004
IPC-CM-770E
Guidelines for Printed Board Component Mounting

1 SCOPE
Class 2 Dedicated Service Electronic Products
This document provides information for preparation of

components for assembly to printed boards, contains a
review of some pertinent design criteria, impacts and
issues, techniques of general interest for assembly (both
manual and machines) and discusses considerations of, and
impacts upon, subsequent soldering, cleaning, and coating
processes. The information herein consists of compiled
data representing commercial and industrial applications.
Includes communications equipment, sophisticated business machines, and instruments where high performance
and extended life is required and for which uninterrupted
service is desired but not critical. Certain cosmetic imperfections are allowed.
This section discusses general recommended assembly

guidelines. Later sections discuss information concerning
specific packaging types.
Sections 2 through 5 provide guidelines for the specific
component within each sectional document. The parts are
described in detail and each section outlines specifics
affecting the part class. The descriptions and classifications
provided are those generally used in the industry with reference to military and commercial applications.
Due to the rapid progress and evolution in packaging and
assembly technology today, this document may not cover
all currently available components or assembly techniques
such as lead free.
Class 3 High Performance Electronic Products
Includes the equipment and products where continued performance or performance-on-demand is critical, such as in
life support items or flight control systems. Equipment
downtime cannot be tolerated and must function when
required. Assemblies in this class are suitable for applications where high levels of assurance are required, service is
essential, or the end-use environment may be uncommonly
harsh.
1.2.2 Producibility Levels IPC standards usually provide
three design complexity levels of features, tolerances, measurements, assembly, testing of completion or verification
of the manufacturing process that reflect progressive
increases in sophistication of tooling, materials or processing and, therefore, progressive increases in fabrication cost.
These levels are:
Level A General Design Complexity - Preferred

The purpose of this document is to illustrate
and guide the user seeking answers to questions related to
accepted, effective methods of mounting components to
printed wiring boards.
1.1 Purpose
1.2 Classification of Board Types and Assemblies
1.2.1 Performance Classes Three general end-product

classes have been established to reflect progressive
increases in sophistication, functional performance requirements and testing/inspection frequency. It should be recognized that there could be an overlap of equipment between
classes. These performance classes are the same for both
bare boards and assemblies. The printed board user has the
responsibility to determine the class to which his product
belongs. The contract shall specify the performance class
required and indicate any exceptions to specific parameters,
where appropriate.
Class 1 General Electronic Products
Includes consumer products, some computers and computer peripherals suitable for applications where cosmetic
imperfections are not important and the major requirement
is the function of the completed electronic assembly.
Level B Moderate Design Complexity - Standard

Level C High Design Complexity - Reduced
Producibility
The producibility levels are not to be interpreted as a
design requirement, but a method of communicating the
degree of difficulty of a feature between design and
fabrication/assembly facilities. The use of one level for a
specific feature does not mean that other features must be
of the same level. Selection should always be based on the
minimum need, while recognizing that the precision, performance, conductive pattern density, assembly and testing
requirements determine the design producibility level. The
numbers listed within the numerous tables are to be used as
a guide in determining what the level of producibility is for
any feature. The specific requirement for any feature that
must be controlled on the end item should be specified on
the master drawing of the printed board or the printed
board assembly drawing.
These levels for assemblies are:
Level A Through-hole component mounting only.
Level B Surface mounted components only.
Level C Simplistic through-hole and surface mounting
intermixed assembly.
1

Ipc CM 770e

Uploaded by

Ipc CM 770e

Uploaded by

IPC-CM-770E

Guidelines for Printed

Developed by the Component Mounting Guidelines Task Group (5-21a)

Users of this publication are encouraged to participate in the

Material Movement Systems ............................ 23

Racks and Carriers ........................................... 23

Order of Precedence ........................................... 3

APPLICABLE DOCUMENTS ................................... 8

Joint Industry Standards ................................... 10

Electronic Industries Association ..................... 10

EOS/ESD Association Documents ................... 10

GENERAL GUIDELINES ........................................ 10

Design Options and Considerations ................. 10

Leadless Component Terminations .................. 11

Leaded Component Terminations ..................... 11

Part Type ........................................................... 11

Assembly Considerations ................................. 12

Component Preparation .................................... 12

Lead Forming ................................................... 12

Component Placement ...................................... 13

Mixed Assemblies ............................................ 13

Component Securing ........................................ 15

Cleaning Agent ................................................. 17

COMPONENT GUIDELINES .................................. 23

Component Characterization and Classes ........ 23

Radial-Leaded Components .............................

Tape Automated Bonding (TAB) ..................... 26

PACKAGING AND INTERCONNECTING

Printed Board Characterization and Classes ....

Supporting-Plane Printed Board Structures ..... 28

Sequentially-Processed Structures with

Printed Boards .................................................. 17

Porcelainized-Metal (Metal Core) Structures .. 30

Board & Lead Finishes .................................... 18

Printed Board with Constraining (Not

Printed Boards with Electrically-Functional

Handling and Storage ....................................... 19

Printed Board with Constraining Core ............ 31

Moisture Sensitivity .......................................... 22

Other Mounting Structure Materials and

Heat Sinks .........................................................

ASSEMBLY DESIGN CYCLE ................................ 34

Solder Pastes and Adhesives ............................ 44

Solder Performs ................................................ 44

Component Spacing .......................................... 44

Wave Solder Component Orientation ..............

Global Fiducials ................................................ 46

Types of Assembly Operations ........................ 34

Sequential Machines .........................................

Inspect Before Assembly .................................. 37

Component Preparation (Tinning/Solder

Mass Attachment Properties ............................. 37

Vias and Land Pattern Separation .................... 48

Controlled Atmosphere Soldering .................... 39

Manufacturing Characteristics .......................... 48

Board Size and Panelization ............................ 49

Panel Format ..................................................... 49

Panel Construction ............................................ 50

PLACEMENT GUIDELINES ................................... 39

Placement Technology ...................................... 39

Process Identification ........................................ 39

Design Checks .................................................. 41

Design Checks for All Assembly Types .......... 42

Design Checks for Surface Mounted

Design Checks for Mixed Technology

Axial-Leaded Discrete Components ................ 52

Packaging Axial Leaded Discrete

Specification and Procurement of

Radial-Leaded Discrete Components ............... 53

Part Type Description ....................................... 53

Product Processes and Applications ................ 43

Component Package Style ................................ 43

Packaging Radial Leaded Discrete

Component Transit Packaging ......................... 43

Multiple-Radial-Lead Components .................. 54

Date of Manufacture and Solderable