CNC Operator Web-Based Tutorial 545

Montez King
AET-545
December 22nd, 2014
Dr. Christine Nortz
CNC Machine Operators

require skills in operating a
CNC machine; the CNC
Machine Operator Program
brings a highly focused,
streamlined set of skills to
CNC Machine Operator
training.
The CNC Machine Operator
Program focuses exclusively
on the modern CNC machine
operator, including such tasks
as maintaining machines and
recording SPC (Statistical
Process Control) data.
Students will demonstrate the ability to operate a

Hass Controller, including key functions as stated
below:
Prestart
Start/Home
Load Tools
Setting Tools
Load CNC Program
Run Program
Shut Down
By the end of the WBT , the student will

demonstrate competency in operating a Haas
CNC controller independently.
By the end of the WBT, the student will pass a
practice CNC Operator exam with a grade of
85% or more.
A CNC (computer numerical control) operator

is someone who operates a CNC machine. The
CNC machine can perform functions, such as
precision drilling and tapping, cutting and
shaping steel and aluminum or milling flat
stock into intricate designs.
Often called a CNC lathe, the operator
programs the machine to perform the task
needed and monitors the work, making all
necessary adjustments as needed.
1.
2.
3.
4.
5.
6.
7.
Prestart
Start/Home
Load Tools
Setting Tools
Load CNC Program
Run Program
Shut Down
Before starting the machine, check to

ensure oil and coolant levels are full.
Check the machine maintenance manual
if you are unsure about how to service it.
Ensure the work area is clear of any loose
tools or equipment.
If the machine requires an air supply, ensure

the compressor is on and pressure meets the
machine requirements.
1. Work Area: Clear

2. Air Supply: On/Correct
Haas requires at least 70PSI for tool changer to operate.
3. Main Breaker: On
4. POWER ON: Press
Ensure Emergency Stop is not tripped. If it is, twist red knob right to release.
Wait until message 102 SERVOS OFF appears before proceeding.
5. RESET: Press
6. Power On Restart: Press
Ensure doors are closed and work area is clear.
Allow all machine axes to home before proceeding.
1. MDI/DNC Key: Select
2. Tool Number: Enter

For example, to position the tool changer
to T1, Press the T and then the 1 buttons.
3. ATC FWD: Select
Tool carousel will index to T1 position.
4. Position Tool in Spindle
Do not grip by tool cutting flutes!
Ensure tool taper is clean.
Grip tool holder below V-flange to
prevent pinching.
Push tool into spindle.
Ensure "dogs" on spindle line up with
slots on tool holder
5. Tool Release: Select

Machine will blow air thru spindle to
clear debris.
Gently push the tool upward and then
release the Tool Release button.
Ensure tool is securely gripped by
spindle before releasing it.
6. Repeat
Repeat steps 2-5 until all tools are
loaded.
1. Handle Jog Mode: Select

This sets machine to be controlled by the hand wheel.
2. Jog Increment: .01
This sets the job increment so each click of the hand
wheel moves the tool .01 inches in the jog direction.
3. Jog Direction: Z
This sets the tool to move in Z when the jog handle is
moved.
1. Memory: Select
2. List Programs: Select
3. USB Device: Select
Use the DN arrow to highlight USB Device on the
graphics screen. (This sets the program list to
display files on the USB Device).
Select F4 button.
1. Pre-Start
Ensure vise or fixture is secure and that you have a safe setup.
There should be no possibility that the work holding will fail to
perform as required.
Remove vise handles.
Clear the work area of any tools or other objects.
Close the machine doors.
Turn Single Block Mode On.
Press Rapid Feedrate -10 button eight times to set rapid Feed Rate
Override to 20% of maximum.
2. Start
Place one hand on Feed Hold button and be ready to press it in case
there are any problems.
Press Cycle Start Button.
1. Remove tool from spindle:

Enter the number of an empty tool carousel.
Select ATC FWD
2. Jog Machine to Safe Area:
Select Jog
3. Shut Down Button: Press
Post Power-Down Checklist:
Wipe spindle with a soft clean rag to remove coolant and prevent rusting.
Put away tools.
Clean up work area.
Always leave the machine, tools, and equipment in the same or better
condition than when you found them.

CNC Operator Web-Based Tutorial 545

Uploaded by

CNC Operator Web-Based Tutorial 545

Uploaded by

Montez King

CNC Machine Operators

Students will demonstrate the ability to operate a

By the end of the WBT , the student will

A CNC (computer numerical control) operator

Before starting the machine, check to

If the machine requires an air supply, ensure

1. Work Area: Clear

1. MDI/DNC Key: Select

2. Tool Number: Enter

5. Tool Release: Select

1. Handle Jog Mode: Select

1. Remove tool from spindle:

You might also like