Final 99 Sol

ChE 344
Chemical Reaction Engineering

Winter 1999
Final Exam
Solution
(25 pts) 1) The gas phase irreversible reaction

A+BC
is elementary. The entering flow rate of A is 10 mol/min and is equal molar in A
and B. The entering concentration of A is 0.4 mol/dm3 .
a) What is the CSTR reactor volume necessary to achieve 90% conversion?
b) What PFR volume is necessary to achieve 90% conversion?
Additional Information
k = 2 dm3 /molmin
T0 = 500 K
Note: You do not need to use POLYMATH, but if you do write your program
below in case you do not obtain the correct answer.
FA0 X = ( rA )V
a)
FA0 = 10
x = 0.9
V =?
rA = kC ACB =
2C 2A0
= 2 (0.4)2
V=
(1 X )
(0.1)2 = 0.01057
(0.55) 2
10 0.9
= 851 dm 3
0.01057
b) FA0 dX = ( rA )dV
0.9
X 2
dX 1
(1 X )2
2
kCA0
V
FA0
1 12 0.9 2 0.42 V
1
1
12
2
1
ln(1 0.9) +
0.9 +
=
2
2
2
1 0.9
10
V=
W99FinalExam
3.63 10
3
4 = 113.3 dm
2 0.4
W99FinalExam
(15 pts) 2) The irreversible zero order gas phase dimerization

2A A2
is carried out in a packed bed reactor with 5 kg of catalyst. The entering pressure
is 10 atm and the exit pressure is 1 atm. Pure A enters at a flow rate of 10
mol/min. The reaction is zero order in A.
P0 = 10 atm
P = 1 atm
FA0 = 10 mol/min
X=?
a) What is the pressure drop parameter ?

b) What is the exit conversion?
k = 1.5 mol/kgmin
T0 = 500 K
Note: You do not need to use POLYMATH, but if you do write your program
below in case you do not obtain the correct answer.
1
A A 2
2
FA0
dX
= (rA )
dW
k
0dX = FA0 W
X=
1.5
W = 0.15W
10
dy
d (1+ X)
=
dw
2
y
5
0 2y dy = 0 1 2 0.15W dW
x
y2
0.1
1
0.15 2 5
= w
w
4
0
0.99 = 5
0.15 25
4
= 4.0625
= 0.2437 kg 1
X = 0.15 5 = 0.75
W99FinalExam
(10 pts) 3) The species A and B react to form species C, D, and E in a packed bed reactor.
The catalyst does not decay. The reaction is elementary. The following profiles
were obtained
T
X .4
500
Circle the correct true (T) or False (F) answer for this system
T
a) The above profiles could represent an adiabatic system where the

addition of inerts will increase the conversion.
b) The above profiles could represent a system where decreasing the

flow rate will increase the conversion.
c) The above profiles could represent a system where if the feed

temperature is increased, one cannot tell from the above profiles
whether or not the conversion will increase or decrease.
d) There could be a heat exchanger on the reactor for which the heat
flow is
dQ
1000 kJ
=
(T 500 )
dW kg s K
e) The above reaction may be an excellent candidate for reactor

staging.
a) The reaction is exothermic and adiabatic. Addition of inerts will lower the exit
temperature and hence will increase the conversion.
b) Decreasing the flow rate will not change the exit condition because it is an
equilibrium condition.
c) Equilibrium is reached early in the reaction, so increase temperature, decrease
equilibrium conversion.
d) Because the ambient temperature is 500, same as final equilibrium temperature.
e) Yes, because it may be an exothermic reversible reaction.
W99FinalExam
(3 pts) 4) The gas phase reaction

2A + B
C
is carried out in a PFR. The feed is equal molar in A and B and the entering
temperature is 500K and the entering pressure is 16.4 atm. If the exit conversion
is X, then the exit concentration of B (in mol/dm3 ) is
a)
b)
c)
d)
e)
f)
CB = 0.4 (1 X) (1 .5X)
CB = 0.4 (1 X)( 1 1.5X )
CB = 0.4
CB = 0.4 (1 0.5X) (1 X )
None of the above
Cannot be calculated without knowing the exit conversion.
A+
1
1
B
C
2
2
= yA0 =
1 1 1
+1
2 2 2
=
1
2
X
X
C A0 B C A0 1
2 =
2
CB =
X
(1 +X )
1
2
= C A0 = 0.2
W99FinalExam
(6 pts) 5) a) The following elementary liquid phase reactions are to be carried out
A + B R
R +B
S
Species R is the desired product. Which of the following schemes should be
used?
A
B
B
A
A
B
(a) PFR
(b) PFR
(c) CSTR
A
B
t=0
B
A
(d) Semibatch
A
B
(e) Batch
A
(f) Semibatch
B
(g)
b) In the reactors
A B
rB = kB C2A
A + B 2C
rC = k CC ACB
What is the instantaneous selectivity of C to B? Which reactor or combination

of reactors and at what temperatures would you use for the following
reaction system?
C is the desired product.
Data for Part (b)
CA0 = 4 mol dm3 k B = 1 dm 3 mol min at 300K with E = 4000cal mol
A
k C = 1 dm 3 mol min at 300K with E = 12000cal mol
High Temp.
W99FinalExam
(a)
r1R = k1R CAC B

r2R = k 2RC R CB
S RS =
rR
r +r
k C C k2S C R CB
= 1R 2R = 1R A B
k2S
r2S
k 2S CRC B
k1R C A
=
1
k2R CR
We can maximize SRS by keeping CA high and CR low. For keeping CR low, keep
C B low because
rR = r1R + r2R
= (k1R CA k2S CR )C B
rR C B
Hence, use either (b) or (d).
(b)
S CB =
rC
k CC ACB
=
rB k C2 1 K C C
B A
2 C A B
1
= k C
1
B
A
kC CB 2
1
8000 CA 1
exp
RT C B 2
We can maximize SCB by keeping

T high
C A low
C B high
Use semibatch
A
and high reactor temperature.
W99FinalExam
(8 pts) 6) a) The following plot of activity as a function of time was obtained.

1
a
1.0
t
What type of decay would best describe to data? (circle the correct answer)
1) Poisoning
2) Sintering
3) Coking
4) None of the above
b) The following profiles were measured in a PBR
t=0
t=10 min
The type of catalyst decay can best be described by (circle the correct answer)
1) Poisoning
2) Sintering
3) Coking
c) The following catalyst activity profile was measured in a PBR for the
isomerization of A to B.
The decay law that best describes this data is (circle the correct answer)
da
1)
= ka
dt
1.0
t = 40 min
a
da
2)
= ka 2
dt
3)
da
= ka C A
dt
4)
da
= ka 2 C B
dt
W99FinalExam
(8 pts) 7) (P10-4) The rate law for the hydrogenation (H) of ethylene (E) to form ethane (A)
over a cobalt-molybdenum catalyst [Collection Czech. Chem. Commun., 51, 2760
(1988)] is
rE =
kPEPH
1 + KE PE
Suggest a mechanism and rate-limiting step consistent with the rate law.
(Can be done by inspection.)
E S
E +S
E S + H 2 A + S (rate limiting step)
W99FinalExam
(5 pts) 8) Suppose the heat exchanger in Example E8-12 became fouled so that the overall
heat transfer coefficient was reduced by 50%?
What would be the new steady state temperatures inside the reactor?
W99FinalExam
10
W99FinalExam
11
(20 pts) 9) The elementary liquid phase reactions

(1)
A B
(2)
2A
C
are carried out in a 100 dm3 PFR where species B is the desired product. Pure A
enters at a molar flow rate of 40.0 mol/min and at a concentration of 4.0
mol/dm3 .
CPA = C PB = 20 cal mol K
CPC = 40 cal mol K
HRx1A =+10,000 cal mol
HRx2A =20,000 cal mol
Ua = 100
cal
with Ta = 400K
dm min K
3
k 1A = 0.05 min 1 at 400K with E = 10,000 cal mol

k 2C = 0.0005 dm3 mol min at 400K with E = 19,000 cal mol
a) For a feed temperature of 450K, what are the exit concentrations and
temperature
2.55 CB = ______,
1.35 CC = ______,
0.05 T = ______K
391
C A = ______,
b) The feed temperature can be varied between 400 and 700. What feed
temperature do you recommend to maximize the exit molar flow rate of B?
T(K)
400
FB (mol/min
12.03
500
18.06
600
2.29
550
3.78
525
5.73
505
15.49
495
16.81
75% Marks for setting up the problem correctly with all correct equations and
numbers in POLYMATH Notation
25% Final Answer
(9)
W99FinalExam
12
W99FinalExam
13
W99FinalExam
14
a) True because initially the reactor temperature decreases.

b) False because in this case, the temperature should not come back to the initial
value.
c) True. The reaction is endothermic and it shows a decrease in temperature first
and then the heat exchanger take sit back to the initial temperature.
(a) (2) second order (sintering?)

(b) (3) coking
(c) activity profile missing
(d)
W99FinalExam
15
W99FinalExam
16

Final 99 Sol

Uploaded by

Final 99 Sol

Uploaded by

ChE 344

Chemical Reaction Engineering

(25 pts) 1) The gas phase irreversible reaction

(15 pts) 2) The irreversible zero order gas phase dimerization

a) What is the pressure drop parameter ?

a) The above profiles could represent an adiabatic system where the

b) The above profiles could represent a system where decreasing the

c) The above profiles could represent a system where if the feed

e) The above reaction may be an excellent candidate for reactor

(3 pts) 4) The gas phase reaction

What is the instantaneous selectivity of C to B? Which reactor or combination

r1R = k1R CAC B

We can maximize SCB by keeping

and high reactor temperature.

(8 pts) 6) a) The following plot of activity as a function of time was obtained.

5) None of the above

E S + H 2 A + S (rate limiting step)

(20 pts) 9) The elementary liquid phase reactions

k 1A = 0.05 min 1 at 400K with E = 10,000 cal mol

a) True because initially the reactor temperature decreases.

(a) (2) second order (sintering?)

You might also like