Engine Valve Lash - Inspect/Adjust: Pantalla Anterior

C15 On-highway Engine BXS00001-UP(SEBP3722 - 51) - Documentacin
Pgina 1 de 5
Pantalla anterior
Bienvenido: r080hem
Producto: TRUCK ENGINE
Modelo: C15 TRUCK ENGINE BXS36881
Configuracin: C15 On-highway Engine BXS00001-UP
Pruebas y Ajustes
C15 On-Highway Engines
Nmero de medio -SENR9692-09
Fecha de publicacin -01/04/2015
Fecha de actualizacin -15/04/2015
i03350581
Engine Valve Lash - Inspect/Adjust

SMCS - 1102-025
To prevent possible injury, do not use the starter to turn the flywheel.
Hot engine components can cause burns. Allow additional time for the
engine to cool before measuring valve clearance.
This engine uses high voltage to control the fuel injectors.

Disconnect electronic fuel injector enable circuit connector to prevent
personal injury.
Do not come in contact with the fuel injector terminals while the engine
is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and
adjustments must be made with the engine stopped and the valves fully closed.
Valve Lash Check
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 05/05/2015
Pgina 2 de 5
An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable
range. Check the valve lash while the engine is stopped. The range is specified in Table 1.
Table 1
Valve Lash
Valves
Acceptable Range for Valve Lash
Inlet
0.38 0.08 mm (0.015 0.003 inch)
Exhaust
0.76 .08 mm (0.030 0.003 inch)
If the measurement is not within this range adjustment is necessary. Refer to Testing And
Adjusting, "Valve Lash Adjustment".
Valve Lash Adjustment
Illustration 1
g01725654
(A) Inlet valves

(B) Exhaust valves
(C) Left side of the engine
(D) Cylinder number
(E) Front of the engine
(F) Flywheel end of the engine
(G) Right side of the engine
Illustration 2
Pgina 3 de 5
g01023432
(1) Valve adjustment locknut

(2) Exhaust adjustment screw
(3) Valve adjustment locknut
(4) Inlet adjustment screw
(5) Place for feeler gauge
Table 2
Valve Lash
Valves
Lash Setting
Inlet
0.38 mm (0.015 inch)
Exhaust
0.76 mm (0.030 inch)
Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust
the valves:
1. Determine the style of variable valve actuator that is installed on the engine.
a. For the BXS engines, remove the variable valve actuators.
b. For the, MXS engines, it is not necessary to remove the variable valve actuators.
2. Put the No. 1 piston at the top center position. See Testing and Adjusting, "Finding Top
Center Position for No. 1 Piston" for further details.
Pgina 4 de 5
Note: If the engine is equipped with an engine compression brake, loosen the adjustment
screw for the lash on the slave piston for the compression brake prior to adjusting the engine
valve lash. Refer to the Testing and Adjusting, "Slave Piston Lash - Adjust" topic in order to
adjust the slave piston lash.
3. With No. 1 piston at the top center position of the compression stroke, an adjustment can be
made to the valves.
Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment
screw. Use a soft mallet to ensure that the lifter roller seats against the camshaft's base
circle.
4. Make an adjustment to the valve lash on the inlet valves for cylinders 1, 2, and 4.
a. Loosen valve adjustment locknut (3) .
b. Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve
bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being
held from turning. Adjust the valve lash until the correct specification is achieved.
Refer to Table 2.
c. After each adjustment, tighten valve adjustment locknut (3) while valve adjustment
screw (4) is being held from turning. Tighten to a torque of 30 7 Nm (22 5 lb ft).
Recheck each adjustment.
5. Make an adjustment to the valve lash on the exhaust valves for cylinders 1, 3, and 5.
b. Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust
valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is
being held from turning. Adjust the valve lash until the correct specification is
achieved. Refer to Table 2.
6. Remove the timing bolt, and turn the flywheel by 360 degrees in the direction of engine
rotation. This will position the No. 6 piston at the top center on the compression stroke.
Install the timing bolt in the flywheel.
7. Make an adjustment to the valve lash on the inlet valves 3, 5, and 6.
b. Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve
bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being
held from turning. Adjust the valve lash until the correct specification is achieved.
Refer to Table 2.
8. Make an adjustment to the valve lash on the exhaust valves 2, 4, and 6.
Pgina 5 de 5

b. Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust
valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is
being held from turning. Adjust the valve lash until the correct specification is
achieved. Refer to Table 2.
9. Remove the timing bolt from the flywheel after all valve lash adjustments have been made.
Refer to the Testing and Adjusting, "Slave Piston Lash - Adjust" topic for information on
adjusting the slave piston lash.
Note: The engine valve lash must be adjusted before you adjust the compression brake.
The lash must also be adjusted on the electronic unit injector. Refer to Testing and Adjusting,
"Electronic Unit Injector - Adjust" for more information.
Copyright 1993 - 2015 Caterpillar Inc.
Todos los derechos reservados.
Tue May 5 21:32:28 EST 2015

r080hem
Red privada para licenciados del SIS.

Engine Valve Lash - Inspect/Adjust: Pantalla Anterior

Uploaded by

Engine Valve Lash - Inspect/Adjust: Pantalla Anterior

Uploaded by

C15 On-highway Engine BXS00001-UP(SEBP3722 - 51) - Documentacin

Fecha de publicacin -01/04/2015

Fecha de actualizacin -15/04/2015