Profiled Metal Roofing The Metal Cladding & Roofing Manufacturers Association Limited PDF

A single copy of this document is licensed to
Licensed copy from CIS: MACE, MACE, 29/05/2016, Uncontrolled Copy.
MACE
On
29/05/2016
This is an uncontrolled copy. Ensure use of the

most current version of the document by searching
the Construction Information Service.
MCRMA Technical Paper No. 6

CI/SfB
(23)
Nh2
JUNE 2004
PROFILED METAL ROOFING

DESIGN GUIDE
THE METAL CLADDING & ROOFING MANUFACTURERS ASSOCIATION LIMITED
Contents
1.0 Typical construction and assemblies

1.1 Introduction
1.2 Single skin system
1.3 Double skin system
1.4 Secret fix
1.5 Site-assembled composite
1.6 Factory made composite panels
1.7 Under-purlin lining
Page
1
1
1
1
1
1
1
2
2.0 Components
2.1 Profiled sheets
2.2 Coatings
2.3 Spacer systems
2.4 Fasteners
2.5 Insulation
2
2
2
3
3
5
3.0 Weathertightness
3.1 Performance requirements
3.2 Roof pitch
3.3 End laps
3.4 Side laps
5
5
5
5
6
4.0 Thermal Performance

4.1 Regulations
4.2 U-values
4.3 Thermal bridging
4.4 Air leakage
7
7
7
9
11
5.0 Interstitial condensation

5.1 Risks of interstitial condensation
5.2 Design to avoid interstitial condensation
5.3 Breather membranes
5.4 Rooflights
13
13
14
14
15
6.0 Acoustics
6.1 Sound reduction
6.2 Sound absorption
15
15
15
7.0 Performance in fire

7.1 Introduction
7.2 Reaction to fire
7.3 External surface
7.4 Cavity barriers
7.5 Building insurance
16
16
16
17
17
17
8.0 Structural performance

8.1 Design loading
8.2 Load span tables
8.3 Spacer systems
8.4 Lateral restraint
17
17
18
18
18
9.0 Durability
9.1 Introduction
9.2 Materials
9.3 Design details
9.4 Maintenance
Page
19
19
19
20
20
10.0 Sustainability
10.1 Sustainable construction
10.2 Life Cycle Assessment
10.3 ISO 14001
21
21
21
22
11.0 Construction details and accessories

11.1 Junction details
11.2 Rooflights
11.3 Roof drainage
11.4 Small penetrations
11.5 Large penetrations
11.6 Flashings
23
23
24
24
24
24
25
12.0 Site work

12.1 General
12.2 Transport, handling and storage
12.3 Site cutting
12.4 Health and safety
26
26
26
26
26
13.0 Inspection and maintenance
27
14.0 References
28
For up to date information on metal roof and wall cladding, including downloadable construction
details, visit www.mcrma.co.uk.
The Metal Cladding & Roofing Manufacturers Association Limited. June 2004
Typical construction and

assemblies
1.1 Introduction
1.4 Secret fix
Profiled steel or aluminium sheets are used in

various roof constructions as shown below. The
guidance in this document applies in principle
to all of these constructions, but primarily to the
double skin system with trapezoidal or secret fix
profiled sheets, which is the most common type of
metal roof construction used in the UK. Sinusoidal
profiles (for example corrugated iron) are not used
for modern industrial and commercial roofs and
they are not covered by this guide. Secret fix
systems and composite panels are both described
fully in separate MCRMA technical guides. The
guidance in this document is generally consistent
with that in BS5427 The Code of Practice for the
use of Profiled Sheet for Roof and Wall Cladding
on Buildings.
Secret fix or standing seam systems use special

profiles for the weather sheet with virtually no
exposed through fasteners. This provides greater
reliability and means they can be used on very low
slope roofs. Secret fix sheets can be used as the
weather sheet in all the roof constructions shown.
NOTE: For detailed information see MCRMA
technical paper No 3 Secret fix roofing
design guide
1.2 Single skin system

An uninsulated profiled metal sheet fixed directly to
the purlins.
Fig 3: Secret fix system
1.5 Site-assembled composite

This is a special site-assembled double skin
construction which uses profiled rigid insulation to
completely fill the space between liner and weather
sheets. The insulation may be polyurethane,
polyisocyanurate or mineral fibre. No spacer
systems are required.
Fig 1: Single skin system
1.3 Double skin system

This common type of construction consists
generally of a shallow profiled metal liner, a spacer
system and an outer sheet usually in a deeper
profile. The insulation is typically a mineral fibre
quilt.
Figure 4 Site-assembled composite
1.6 Factory made composite panels
Fig 2: Double skin system
These panels combine a liner, rigid insulation and

weather sheet in a single factory made component.
Although it is possible to use various types of rigid
insulation only polyurethane and polyisocyanurate
expand and autohesively bond to the facings
during manufacture and they are therefore used for
the majority of composite roof panels.
Components
NOTE: For detailed information see MCRMA

technical paper No 9 Composite roof and
wall cladding design guide
Steel and aluminium roofing sheets are produced

by MCRMA members in a wide variety of profile
shapes, coatings and colours. The details below
are for general guidance and full details of
products should be obtained from the individual
manufacturers. Component and system durability
is discussed in Section 9.0.
2.1 Profiled sheets

Profiled weather and liner sheets are made of steel
to BS EN 10147 or aluminium to BS EN 485 (and
related standards).
Fig 5: Factory made composite panel
1.7 Under-purlin lining

Note that where under-purlin lining is required for
hygiene reasons, for example in food processing
buildings, an additional liner must be used in
conjunction with a standard over-purlin Insulated
cladding system.
Thicknesses vary depending on product and

application but the values in Fig 6 are generally
regarded as minimum values in mm.
STEEL
ALUMINIUM
Weather sheet
0.7
0.9
Liner sheet
0.4
0.5
Walkable liner sheet
0.7
0.9
Fig 6: Minimum sheet thicknesses

The depths of trapezoidal profiles are typically
32mm for the weather sheet and 20mm for the
liner, but note that the weather sheet depth in
particular might vary considerably. Cover widths
vary similarly but are often about 1m.
2.2
Coatings
All steel faces are hot dip galvanised or aluzinc

coated and painted to provide the required
appearance and durability. Aluminium is supplied
with a mill or painted finish.
The coatings shown in Fig 7 are commonly
available in a wide range of colours. Individual
manufacturers may supply others.
Type
Substrate
Typical thickness:
microns
Application
Plastisol
steel
200
weathersheet
Pvf2
steel and aluminium
25
weathersheet
Multicoat
steel and aluminium
100
weathersheet
ARS
aluminium
28
weathersheet
Polyester
steel and aluminium
22
liner
Fig 7: Typical coatings

NOTE: The standard liner specification is for normal internal environments. Higher specification coatings
should be used where there are aggressive environments or where hygienic finishes are required.
Full details of the range of available coatings can be obtained from the individual manufacturers.
2.3
Spacer systems
The spacer system in a double skin metal roof

is used to create a cavity between the liner and
weather sheet for the layer of insulation. The
spacers are structural items, which support the
weather sheet and they are always positioned over
purlins or other structural members and must be
fixed securely to them.
Traditional
zed spacer
and ferrule
Zed spacers (or minizeds) made of galvanised

steel approximately 1.5mm thick and supported on
nylon ferrules were the standard solution for many
years. They are generally suitable for layers of
insulation up to 100mm thick but at greater depths
the traditional zed/ferrule arrangement is not
adequately stiff or stable.
A new generation of spacers consisting of roll
formed rails of structural grade steel with plastic
blocks or bracket supports and thermal break/
vapour seal pads have been developed and are
now commonly used. These are generically known
as rail and bracket systems. The designs are
engineered to be more stable at a range of depths
to suit most insulation thicknesses likely in the
future, and they also minimise thermal bridging.
Typical spacer systems are shown in Fig 8.
Fig 8: Typical spacer systems
2.4
Fasteners
There are many proprietary fasteners available and

it is not possible to describe them all in this guide.
The details below are for general guidance. For
detailed information see MCRMA technical paper
No 12 Fasteners for metal roof and wall cladding:
design, detailing and installation guide. Further
specific details can be obtained from the cladding
and fastener manufacturers.
Fasteners can be divided into two distinct

categories:
a) Primary
These fasteners are designed to transfer all loads
on the cladding system back to the supporting
structure so their strength is particularly important.
If the fasteners are exposed they must also
provide a weathertight seal. They are normally
used in the valley of the profile. If crown fixing
is recommended by the manufacturers, saddle
washers are usually required.
Fig 9: Typical primary fastener positions

The most common fasteners are self-drilling and
self-tapping which can be installed in one simple
operation into a variety of materials. Self-tapping
screws (with no drill point) are also available and
may be preferred in some applications. Most
screws are now available in plated carbon steel or
stainless steel, they come complete with a 16mm
or 19mm diameter sealing washer and they can
have integral colour matched plastic heads or
separate push-on plastic caps. The strength of
a fixing depends on the fastener design and the
thickness and yield strength of the purlin. Fastener
manufacturers and suppliers can supply strength
data for their products installed in a range of
materials and thicknesses.
b) Secondary
These fasteners are used to connect side laps,
flashings etc. and they are not normally considered
as structural. However, where the fasteners are
providing lateral restraint or in a stressed skin
design, their strength would have to be considered
in the structural calculations.
Self drilling and tapping
Bracket
to purlin
Outer sheet
to spacer
Mini-zed to
purlin
through
ferrule
Composite
and siteassembled
composite
Self tapping
Metal
sheet to
hot rolled
steel
Metal sheet
to timber
Fig 10: Primary fasteners
Self drilling stitcher screws
Rivets
Neoprene grommet for rooflights
Fig 11: Secondary fasteners
Weathertightness
In most cases these fasteners are exposed so

they must provide a weathertight seal. The most
common types are self-drilling and self-tapping
stitcher screws with sealing washers and plastic
heads/caps, or sealed rivets with or without plastic
caps.
When selecting the fasteners for a roof, the
structural performance, environmental conditions,
corrosion resistance (including bi-metallic
corrosion), weathertightness and ease of
application must all be considered.
2.5 Insulation
The majority of site-assembled double skin roof
constructions use mineral fibre (glass or rock)
quilt insulation supplied in rolls. When unrolled on
site the material expands to at least its required
thickness and normally fills the cavity created by
the spacer system between the liner and weather
sheet. The material is normally quite soft and
deforms around the small profiled ribs on the liner,
and under and around the spacer system.
Rigid mineral fibre insulation slabs are also used
in some circumstances but this is less deformable
than the quilt and the roofing system has to be
designed and installed with this in mind so that no
gaps are left in the insulation layer.
Site-assembled composite constructions do not
use spacer systems and rely on the rigidity of the
insulation and special fasteners to support the
outer sheet. In this case rigid profiled polyurethane,
polyisocyanurate, and mineral fibre insulation are
used.
3.1 Performance requirements

The effects of the internal and external conditions
on roof constructions are more severe than on
wall cladding. The satisfactory performance of
any roof cladding system depends on the correct
selection of materials, and the design, detailing
and assembly of every aspect of the construction.
The position and shape of the building, all types of
loading and the internal and external environments
must all be considered.
3.2 Roof pitch

Over recent years roof pitches on industrial and
commercial buildings have tended to be as shallow
as possible in order to reduce the heating costs
of the large empty roof spaces, and for aesthetic
reasons. Most through fixed trapezoidal metal roof
sheets incorporating normal side and end laps
are suitable for roof pitches of 4 or steeper. Note
that the risk of leakage decreases as the pitch
increases. For increased reliability and for pitches
down to I (after all deflections), a secret fix system
must be used with no exposed through fasteners,
special side laps and preferably no end laps.
NOTE: For detailed guidance refer to MCRMA
technical paper No 3 Secret fix roofing
design guide.
3.3 End laps

The standard end lap arrangement for trapezoidal
steel weather sheets at any roof pitch greater than
or equal to 4 is shown in Fig 12. Typically, two
continuous runs of 6 5 or 6mm diameter butyl
sealant strips are used. The lower run is the
primary weather seal and should be positioned
as close as possible to the edge of the top sheet.
The upper seal is to prevent moisture entering the
overlap from inside the cavity.
The fasteners clamp the two sheets directly to the
spacer (or rigid insulation) and both runs of sealant
are compressed. The frequency of the fasteners
depends on the profile but must be sufficient to
consistently clamp the sheets and seals along the
full length, typically every trough. For optimum
durability the edge of the overlapping sheet must
be painted.
It is common to see specifications recommending

that side laps should be arranged away from the
prevailing wind. This is sensible in principle but is
often not practical. The joint must be weathertight
in all circumstances.
150mm
m
m
15
Two runs
of sealant
Alternative seal positions
Fig 12: End lap detail for roof pitches greater than 4
Aluminium weather sheets may require a slightly
different end lap arrangement to allow for the
coefficient of linear expansion, which is twice that
of steel. The actual arrangement will depend on
the length and colour of the sheets. The colour
determines the maximum temperature that the
sheets reach and therefore the maximum degree
of expansion.
Fig 13 shows a typical detail, which allows some
movement at the end lap joint without affecting
the fasteners. Special sealants need to be used
to provide a suitable sliding joint, and the overlap
may be increased to 200mm. When aluminium
profiles are being considered the manufacturers
recommendations should be followed.
Fig 14: Typical side lap detail

Typically, a continuous run of 6 5 or 6mm
diameter butyl sealant strip is used on the centre of
the underlapping rib or on the weather side of the
lap on all trapezoidal sheets. All trapezoidal roof
sheets should be stitched through the centre of
the top of the side lap at typically 450mm centres
using sealed stitcher screws or rivets.
200mm
Two runs
of sealant
Fig 13: End lap detail to allow some movement in

the joint
For increased reliability the number of end laps
should always be minimised as far as possible.
3.4
Side laps
A typical side lap between trapezoidal sheets

is shown in Fig 14. This arrangement is ideal
because the outer rib of the underlapping sheet
is complete and provides the optimum support for
the overlapping sheet so that the side lap can be
sealed and stitched effectively.
Thermal Performance
4.1 Regulations
The thermal performance of the roof cladding is
important because it affects the amount of energy
required to heat the building and will influence the
running costs and the comfort of the occupants.
Approved Document L2 to the Building Regulations
(2002 Edition) Conservation of Fuel and Power
defines the required levels of performance in
terms of U values, thermal bridging, and air
tightness, and explains how the requirements can
be achieved. Site testing of the completed building
is required in many cases, to ensure the design
performance has been achieved. It means that the
building designer and cladding contractor need to
pay more attention to the thermal performance of
individual details of the construction, which were
not previously defined.
The Approved Document refers to MCRMA
technical paper No 14 Guidance for the design
of metal roofing and cladding to comply with
Approved Document L2:2001, for further more
detailed information.
4.2 U-values
4.2.1 Methods of determining U-values
The elemental U-value or thermal transmittance
specified in Approved Document L2 for industrial
and commercial roofs is 0.25 W/m2K.
Approved Document L2 requires that profile
shapes, and repeating thermal bridges, such as
metal spacers and other fixings, are taken into
account when a U-value is calculated using the
combined method, which is specified in BS EN
ISO 69461 and CIBSE Guide A32. However, this
method is designed to deal with the type of thermal
bridges such as timber studs, which distort the
heat flow relatively little, and it specifically excludes
elements in which the insulation layer is crossed by
thin metal components.
Ultimately, the U-value of this type of element
has to be calculated by developing a full two- or
three-dimensional thermal model of the structure
to calculate the heat flows. This is a complex task
requiring software, which complies with BS EN
ISO 10211:19963, and is usually carried out only
by specialist consultants. A number of system

manufacturers provide U-values of their systems
for different insulation thicknesses, fixing spacings,
etc that have been calculated by independent
bodies.
A range of simplified methods has been developed
for use in specific cases; these can be obtained
from the following sources:
-
Twin-skin systems with zed spacers are

covered in BRE Information Paper IP 10/024.
Twin skin systems with rail and bracket spacers

are covered in SCI Technical Information Sheet
P3125.
A software package KOBRA, which allows the

calculation of the thermal properties of a range
of wall and roof systems is used by members
of the MCRMA.
A U-value calculator, which covers all types

of walls, roofs and floors, is available and can
be downloaded from http://projects.bre.co.uk/
uvalues/.
The appropriate methods that should be used to

calculate U-values in all instances are specified in
BRE Report BR4436.
Alternatively the thermal transmittance (U) of a
roof cladding construction can be measured using
a calibrated hot box, in accordance with EN ISO
8990.
4.2.2 Insulation thickness required
The following table indicates the approximate
insulation thicknesses required to achieve a Uvalue of 0.25 W/m2K using a typical type of rail
and bracket, liner and outer sheet. The effect of
different insulation materials and varying purlin and
bracket centres is also indicated.
Purlin spacing : m
Insulation
conductivity : W/mK
Bracket
spacing : m
0.9
1.4
1.8
0.035
0.5
175
160
155
1.0
160
150
150
0.5
210
195
185
1.0
190
180
175
0.5
220
210
200
1.0
205
200
195
0.04
0.045
Fig 15: Insulation thickness in mm necessary to achieve a U-value of 0.25 W/m2K

(Assuming a liner sheet with 18mm profiles at 200mm centres and an outer sheet with 35mm profiles at
167mm centres)
These are the theoretical minimum insulation

thicknesses required. In practice, the insulation
quilt used is normally selected from a range of
standard thicknesses such as 80mm, 100mm etc.
and a building might contain a variety of purlin
spacings so the construction and materials have to
be specified with care.
No matter which insulation is used it is vital that the
material is installed carefully throughout, ensuring
there are no gaps particularly at apertures, ridge,
eaves, corners etc. The continuity of insulation is
specified in the Regulations, and a thermographic
survey might be used to check the consistency of
the insulation in the completed building. Individual
manufacturers literature provides details of their
systems.
In some cases it may only be necessary for the
roofing supplier to demonstrate that the system
U-values are less than or equal to the value of
0.25 W/m2K required in Approved Document
L2. However a more detailed knowledge of
the specific U-values of all the elements of the
building will be necessary if it is proposed to
trade off areas, assess the contribution of thermal
bridges or trade off heating system efficiency with

improved fabric performance (see below). In these
cases it will be necessary for some member of
the design team, generally the architect, to take
responsibility for collating the heat loss from all
the plane areas (U-values), and thermal bridges at
junctions between the plane areas (-values), and
dimensions of the individual components, from a
number of different suppliers.
4.2.3 Trading off U-values and areas
Within certain constraints, Approved Document L2
allows trading between the elemental U-values and
the areas of components specified in the Approved
Document, provided that the overall heat loss
from the building is less than that from a notional
building of the same size and shape, with the
elemental U-values and areas.
The various constraints are:
a. The U-value of any opaque part of a roof is no
worse than 0.35 W/m2K.
This constraint is designed to reduce the risk
of surface condensation. It accommodates
situations, such as the need to include more
fixings, which raise the U-value, in areas of a
roof subject to greater wind uplift. The area

weighted average U-value of the roof should
meet the 0.25 W/m2K limit.
b. If the area of openings in the proposed building
is less than the values shown in the Approved
Document, the area weighted average U-value
of the opaque parts of the roof cannot exceed
the appropriate value in Table 1 of Approved
Document L2 by more than 0.02 W/m2K.
c. No more than half the allowable rooflight area
can be converted into an increased area of
windows and doors.
The possibilities for trading off and the constraints

may be illustrated by some specific examples:
A) Table 1 of Approved Document L2:2002 gives
the elemental U-values for a roof with integral
insulation as 0.25 W/m2K and for rooflights as 2.2
W/m2K. Table 2 gives the maximum allowable roof
light area as 20%. This means that the average
U-value for the roof will be 0.8 0.25 + 0.2 2.2 =
0.64 W/m2K.
If the rooflight area was only 10%, the rooflight
U-value could be increased to Url so long as the
relationship: 0.9 0.25 + 0.1 Url 0.64 was
satisfied. This means that Url can be as high as
4.1 W/m2K. It is not, however possible to carry out
the similar calculation: 0.9 Urf + 0.1 2.2 0.64
to allow a U-value of the opaque parts of the roof
up to 0.47 W/m2K; constraint b), above, limits this
to 0.27 W/m2K.
B) If, for structural reasons, more fixings are used
near the eaves and ridge, raising the U-value of
25% of the opaque area of the roof to 0.35 W/m2K,
the maximum allowed by constraint a), the U-value
of the remaining 75% of the opaque part of the roof
has to be reduced to satisfy:
0.75 Urf + 0.25 0.35 0.27, i.e. to 0.24 W/m2K.
4.2.4 Responsibility for calculation of U-values
The U-values of the individual components of a
building should be specified during the design
stage. These will often follow the elemental values
specified in Table 1 of Approved Document L2,
however there may be circumstances in which
lower (better) values may be specified in certain

areas to allow trading off with other areas. The
responsibility for calculating the U-values of
cladding systems usually lies with the supplier
of the system, who should be in a position to
justify the values quoted by reference to the
documentation discussed above or by producing
results from calculation carried out to BS EN ISO
6946 or BS EN ISO 10211-1 as appropriate. The
values for other cladding elements such as smoke
vents or rooflights should be provided by the
appropriate manufacturer.
4.3 Thermal bridging

4.3.1 Effects of thermal bridging
Thermal bridges are areas of the fabric where the
geometry of the structure and/or the presence of
high conductivity materials crossing the insulation
lead to heat flows that are locally higher than in
surrounding areas. These both add to the total
energy demand of the building and lower the
internal surface temperatures. Depending on the
environmental conditions within the building and
the nature of the internal surfaces this can lead
to surface condensation or, less commonly in
industrial buildings, mould growth.
Approved Document L2 requires that the building
fabric should be constructed so that there are no
significant thermal bridges or gaps in the insulation
layer(s) within the various elements of the fabric,
at the joints between elements and at the edges
of elements such as those around window and
door openings. Thermal bridging within elements,
such as at spacers, is taken into account when
calculating U-values, so here it is necessary to
concentrate on the thermal bridging at junctions
and penetrations. One way of demonstrating
compliance is to utilise details and practice that
have been independently demonstrated as being
satisfactory. This can be done for domestic style
constructions by following the details given in the
robust construction details publication. However,
as these often do not apply to industrial buildings,
calculations or the use of robust design practices
must be used to demonstrate compliance. BRE IP
17/017 and the MCRMA technical paper No 148
specify the necessary procedures.
4.3.2 Design to avoid condensation and mould

growth
In buildings, especially housing, which have
absorbent internal surfaces, the lowered surface
temperatures at thermal bridges can cause mould
growth, which is a major cause of respiratory allergies
such as asthma. Mould growth, which occurs at a
surface relative humidity of 80%, is, however, very
rare on the impermeable internal surfaces of metal
faced roofs. Condensation, depositing drops of
water on the surface, which does not occur until the
surface relative humidity has reached 100%, is much
more likely in this case. Even when condensation
occurs, often less than 10 grams per square metre
accumulate, seen as a fine mist on the surface,
which rapidly disperses as temperatures rise. At
least 70 g/m2 must accumulate before it will run
down a sloping surface and 150g/m2 before dripping
will occur from a horizontal surface.
The concept of surface temperature factor, or
f-value, is used to separate the performance of
the structure from the imposed environmental
conditions; this is defined by:
f
where
Ts - Te
Ti - Te
Ts is the local surface temperature

Te is the external air temperature
Ti is the internal air temperature.
Surface temperature criteria, which define fmin

and which are more appropriate to industrial
buildings have been established based on BS
EN ISO 13788:20019. Different building types fall
into the different classes shown in Fig 16, with
the minimum f-values, which are required to avoid
condensation in the different internal environments.
The f-value for a particular construction can be
established by computer modelling, as part of the
heat loss calculation (see 4.3.4).
4.3.3 Design to reduce heat loss through
thermal bridges
Heat loss through linear thermal bridges (at
junctions and openings) is expressed in terms
of the linear thermal transmittance or -value
(pronounced psi). This is the extra heat loss
Humidity
class
Building type
Minimum
f-value
Storage areas
0.30
Offices, shops
0.50
Dwellings with low

occupancy
0.65
Dwellings with high

occupancy, sports
halls, kitchens,
canteens; buildings
heated with un-flued
gas heaters
0.80
Special buildings,
e.g. laundry, brewery,
swimming pool
0.90
Fig 16: Internal humidity classes and the

minimum temperature factor necessary to prevent
condensation
through the junction, over and above the heat loss
through the adjoining plane elements.
BRE IP 17/01 contains a table of -values for
thermal bridges in typical domestic constructions;
if the calculated -values in the building under
design are less than or equal to these values,
then no further action is necessary. If the thermal
bridges under investigation do not appear in this
table, which is most likely in the case of industrial
buildings, the total heat loss for the building
fabric must be calculated, and compared with
the permitted maximum heat loss from a notional
building with the same size and shape.
The permitted heat loss through thermal bridges is
10% of the sum of the heat loss through the plane
areas of the notional building. So to satisfy the
Regulations:
AacUac + L < 1.1 AelUel
Where: Aac and Uac are the elemental areas and
U-values of the real building.
L is the sum of the heat loss through
junctions.
Ael and Uel are the elemental areas and Uvalues of a notional building with the same
size and shape as the real building.
10
The fact that the heat loss from the real building
is compared with that from the notional building
means that, provided that the surface temperature
criteria in Fig 16 are met, it is possible to trade off
areas and U-values against thermal bridges. So
that if it was not possible to design out a severe
thermal bridge, the criterion could, for example, be
met by reducing the rooflight area from 20%, while
retaining the rooflight U-value at 2.2 W/m2K. (See
example in MCRMA technical bulletin No 11).
The calculation of -values and f-values is not

required by Scottish Technical Standard J.
4.3.4 Sources of -values and f-values
Because thermal bridges occur at junctions,
complex two dimensional calculations using
software that complies with BS EN ISO 102111:1996 are needed to determine the -values and
f-values. These can be carried out by specialist
contractors, but are time consuming and expensive.
A number of manufacturers have commissioned
calculations of the necessary values and publish
them in catalogues of standard details. These are
generally accepted by building control authorities.
There are however, no generally accepted
conventions for carrying out these calculations,
and it is possible that cases of dispute will arise.
While cladding suppliers can generate the
necessary thermal bridge parameters for their
systems, there may be particular difficulties
where different systems meet, for example where
a twin skin roof from one manufacturer meets
a composite panel wall from another. In these
cases it will be necessary for the building designer/
architect to arrange for the -values and f-values
to be calculated for the particular instance.
Calculating the total heat loss for the building
requires information on the areas and U-values,
and details of junctions of all the various
components of the building, which will have been
provided by a number of suppliers and trades.
This means that realistically it can only be done by
the building designer/architect.
Some typical junction details for twin skin metal
roofing are shown in section 11. Many of these
11
have no additional metal crossing the layer

of insulation and the insulation is effectively
continuous, and as a result the values are very
low. Any details which incorporate these design
principles would be expected to have low values,
and contribute very little to the total heat loss from
the building.
4.4 Air leakage

Besides the fabric heat loss through the plane
areas and thermal bridges, described in sections
4.2 and 4.3, air leakage from the interior can add
very significantly to the total energy demand of
a building. Ventilation heat loss can account for
as much as 50% of the total heat loss from a
leaky building, leading to a significant potential
for savings if the leakage paths are identified
and sealed. A further disadvantage of very leaky
buildings is that their internal environment is
difficult to predict and control, leading either to
plant oversizing or to uncomfortable conditions
within the building.
Approved Document L2: 2002 lays stress on
the need to achieve a reasonable standard of
airtightness, and makes suggestions as to how
this might be achieved by appropriate sealing
measures. It also suggests that it may be
necessary to demonstrate compliance with a report
from a competent person that appropriate design
details and building techniques have been used
or, for buildings larger than 1000 m2 floor area,
to carry out an air leakage test. It is, however,
important to remember that the cladding system is
only one of the areas of the building envelope that
contribute to the leakage. Junctions and openings
such as doors, loading bays, windows, rooflights,
smoke vents and service penetrations may be
more important.
4.4.1 Methods for measuring airtightness
Techniques for the testing and analysis of the air
leakage of buildings are described very fully in
CIBSE Guide TM23, which should be consulted for
fuller information. An air leakage test is carried out
by mounting a fan (or fans) in a suitable aperture
within the building envelope, usually a doorway,
running the fan to blow air into the building creates
a pressure difference across the building envelope

see Fig 17 and Fig 18. The fan speed is varied to
create a range of pressure differences up to about
50 Pa (1Pa = 1N/m2) and the flow rate recorded at
each stage. The flow rate at 50 Pa, Q50, normally
in m3/h, which is found from a plot of the flow
rate against pressure difference, is reported as
the parameter which defines the leakiness of the
building.
Fig 17: Diagrammatic representation of whole

building leakage test
Fig 18: Large fan for testing industrial buildings

A pressure test relies on the assumption that
the pressure difference is uniform over the
entire building envelope. This imposes certain
restrictions on the external climate parameters
that prevail during the test. Ideally the internal
to external temperature difference should be less
than 10C and the wind speed should be less than
3 m/s. Higher temperature differences lead to
high stack pressure differences that distort the test

results, especially in very tall buildings, and high
wind speeds cause random pressure differences,
which make accurate readings difficult.
During a test, all internal doors should be wedged
open and, where appropriate, combustion
appliances must be switched off and any open
flues and air supply openings temporarily sealed
(flues from room-sealed appliances, such as
balanced flues in domestic appliances, do not need
to be sealed). External doors and other purposemade openings in the building envelope should be
closed and mechanical ventilation systems turned
off, with the inlet and outlet grilles sealed. Fire
dampers and ventilation louvres should be closed.
Drainage traps should contain water.
The cladding or roofing system is only one of the
possible leakage routes from a building and a
simple fan pressurisation test quantifies the total
air leakage of a building, but does not directly
identify the leakage paths. A number of methods
can be used to provide more information, including
releasing smoke from smoke pencils or puffers to
visualise specific flow paths; an internal infra-red
survey of a depressurised building in cold weather
will rapidly reveal areas that are being chilled by
incoming air; repeated testing of a building as
successive specific components are sealed, and
isolating and testing specific components.
4.4.2 Required air tightness
The parameter that is specified in Approved
Document L2 to quantify the air leakage
rate through the building envelope is the air
permeability. This is measured by the fan
pressurisation technique and is expressed in terms
of the volume flow of air per hour (m3/h) supplied
to the space, per square metre (m2) of building
envelope (including the ground floor area) for a
specified inside to outside pressure difference of
50 Pa.
Section 2.4 of Approved Document L2 requires
that the air permeability should be less than
10 m3/h/m2 at 50 Pa.
12
Interstitial condensation
4.4.3
Important leakage routes
To minimise air leakage through twin skin metal
roofing, the liner side of the construction must be
sealed as effectively as possible. This involves
sealing:
- Liner end laps typically with butyl sealant strip

and additional fasteners
- Liner side laps and side joint at perimeter
typically with a wide butyl faced tape
- Fasteners with normal washers
- Perimeter or ends of sheets with profiled liner
fillers and additional fasteners
- Any penetrations such as pipes
With a good standard of construction and good
attention to detail it is easy to achieve a twin skin
metal roof structure that is tight enough to pass the
Approved Document L2 criterion.
However, as noted above, the cladding system is
only one of the areas of the building envelope that
contribute to air leakage. Junctions and openings
such as doors, loading bays, windows, rooflights,
smoke vents and service penetrations, may be
more important.
The typical junction details shown in section 11
indicate where air seals have to be fitted, but
reference should be made to manufacturers
information for details of their particular systems.
In every case, satisfactory sealing will only be
achieved by good workmanship on site.
Interstitial condensation means condensation

that occurs inside a construction, usually hidden
from view. In normal metal clad industrial building
applications it is not an important issue, but in
some more specialist applications it can be a
critical issue.
5.1 Risks of interstitial condensation

Interstitial condensation may occur if water
vapour, generated within the building, is able to
penetrate the liner and reach cold areas outside
the insulation, where it may condense, usually
on the outer sheet. If sufficient condensation
occurred, it could potentially cause problems such
as corrosion of metal components and wetting
of thermal insulation, and the condensate could
run into the building staining internal finishes or
dripping onto equipment or processes. Because of
the inherent impermeability of metal liners, these
problems do not occur in normal applications.
Small amounts of condensate, 0 10 g/m2, a
fine mist, will commonly occur on most nights,
even in the summer, however these will usually
evaporate rapidly during the day, without leading to
any long term accumulation. Problems will occur
when the rate of condensation is high enough to
allow accumulations sufficient to cause running or
dripping of the condensed water.
The risks of interstitial condensation depend on
the design and construction of the roof, and the
internal and external climate of the building. Risks
will be higher in colder external climates and in
buildings such as swimming pools, laundries
or some food processing plant, that operate at
high internal humidities. Buildings, which are
operated at an over pressure, to reduce the
ingress of contaminants, are at especial risk as
the over pressure can drive warm moist air into the
structure.
It should be remembered that, while interstitial
condensation is usually caused in the UK by cold
external climates, severe problems can occur in
air conditioned buildings in warm humid climates,
when the vapour drive is from outside to in. It
is essential that designs are appropriate to the
climate in which the building is situated.
13
General guidance for the design of structures

to minimise the risks of interstitial condensation
is given in BS5250:2002 and a procedure for
calculating the accumulation of condensate in any
climate is given in BS EN ISO 13788:2002.
5.2 Design to avoid interstitial

condensation
The moisture content of the internal environment
should be assessed and, if appropriate, controlled
by providing the correct levels of ventilation or
by air conditioning. This would normally be the
responsibility of the building services engineer.
However, it should be recognised that there will
be some degree of moisture load in almost all
building; the design of the roof structure should
therefore:
prevent water vapour reaching the cold

areas of the roof structure, by including an
impermeable vapour control layer on the warm
side of the insulation; and
provide means for any water vapour that does
penetrate the structure to escape.
5.2.1 Vapour control layer

To minimise the potential for interstitial
condensation in double metal skin construction
the most critical part of the construction is the
vapour control layer. This is used to minimise the
amount of moisture vapour which can enter the
construction by diffusion and air leakage. It must
be positioned on the warm side of the insulation.
The vapour control layer can be made by carefully
sealing the profiled metal liner or by providing a
separate polythene membrane on top of the liner.
In either case it is essential that the vapour control
layer is continuous throughout the roof and all
laps are sealed, including at abutments, rooflights,
penetrations, gutters, ridge etc. Note that
constructing the liner to minimise air leakage (see
section 4.4) will automatically provide the vapour
control layer.
The same principles apply to all the other types
of metal roof construction shown in section 1. All
systems require attention to detail in their design
and construction on site.
5.2.2. Ventilation
No matter how well the vapour control layer is
constructed, some moisture vapour may get into
the construction and there must be provision in the
design to deal with it. The smaller the roof voids
and the insulation cavity the less moisture there is
likely to be present to condense. The roof voids
should therefore be the minimum required and the
weathersheet should be in contact with the insulation.
In site-assembled double skin constructions with
standard trapezoidal sheets ventilated fillers
must be used at the ridge and eaves to allow
some breathing through the ribs in the profiled
weathersheet. This helps to disperse any moisture
vapour which is in the construction.
Other types of profiled sheets, such as secret fix,
use different methods of ventilation. See individual
manufacturers details.
5.3 Breather membranes

A breather membrane is sometimes fitted on top
of the insulation in site-assembled double skin
constructions. This is designed to allow moisture
vapour to breathe out of the construction and to
prevent any condensation, which might form on
the ribs of the outer sheet from dripping onto the
insulation. It should be detailed to allow any water
on its surface to drain down to the gutter.
Experience has shown that a breather membrane
is not required in most circumstances. Its
requirement depends on the buildings internal
environment and the application. In normal
applications, provided the vapour control layer
has been properly installed, the amount of
condensation is likely to be small and no breather
membrane is required. A breather membrane
only needs to be considered when the building
has a high humidity internal environment, and
then it should only be used in conjunction with an
effective vapour control layer and eaves to ridge
ventilation through the profile ribs.
Site-assembled composite systems and factory-made
composite panels with rigid foam insulation have no
voids above the insulation so there is no requirement
for rib ventilation or breather membranes.
14
Acoustics
5.4 Rooflights
Ensuring continuity of the vapour control layer and
ventilation through profiled ribs normally means
that site-assembled rooflights should be used
with site-assembled double skin cladding systems.
Factory-assembled rooflights are used with
composite panels.
The acoustic performance of a building can

be an important aspect of the design and the
roof construction can play a major role in the
performance. For detailed guidance see MCRMA
technical paper No 8 Acoustic design guide for
metal roof and wall cladding. There are two
potential acoustic requirements:
Compared to the surrounding insulated cladding,

rooflights have a significantly worse thermal
performance, there is therefore an increased
potential for condensation at rooflights. Misting
of all factory or site-assembled rooflights can
be anticipated from time to time, but it generally
dissipates without harmful effects. However, if
condensation is unacceptable rooflights should be
avoided completely.
In this case the objective is to provide sound

reduction through the structure in order to reduce
the airborne transmission of noise inside a
building to the outside, or vice versa. The level of
performance is referred to as the Sound Reduction
Index (SRI), measured in decibels (dB). Increasing
the SRI by 3dB will approximately halve the
transmitted sound energy.
NOTE: For detailed guidance refer to MCRMA

technical paper No 1 Recommended
good practice for daylighting in metal clad
buildings.
6.1 Sound reduction
While all metal skin roofing will provide some

degree of sound reduction the best performance is
achieved with double skin constructions using soft
mineral fibre insulation. Additional layers may be
added within the construction, to further improve
the performance. Generally the heavier the
cladding materials the better the Sound Reduction
Index. The actual performance of each cladding
system also depends on the weathersheet and
liner profiles and the method of assembly.
As a guide a typical site-assembled double skin
steel roof cladding might achieve a weighted
Sound Reduction Index (Rw) of approximately
38 dB whereas the value for a factory-made
composite roof panel (rigid insulation) might be 26
dB. Individual manufacturers can provide advice on
their own systems.
6.2 Sound absorption

Sound absorption is used to reduce noise levels
and improve the acoustics inside a building by
reducing unwanted multiple reflections from hard
internal surfaces (reverberation). This can be
achieved with site-assembled double skin systems
by using a perforated liner and mineral fibre
insulation see Fig 19. The perforations allow the
noise to enter the insulation where it is absorbed.
A typical system would include a polythene vapour
control layer over a relatively thin layer of acoustic
15
Performance in fire
insulation, followed by the main layer of thermal

insulation. The acoustic insulation should be
faced with a glass fibre tissue or similar, to reduce
the risk of dust falling through the perforated
liner. The exact acoustic performance of a roof
cladding cannot be assumed from data for a similar
construction and must be determined by test.
7.1 Introduction
The manner in which all elements of building
construction perform in the event of a fire is of
prime concern to the designer, the occupant,
the building owner and the building insurance
company. Profiled metal cladding constructions
must therefore conform to specific requirements
which are defined in the Building Regulations
Approved Document B. They may also have
to comply with other requirements defined by
building insurance organisations, such as the Loss
Prevention Council (LPC).
The purpose of the Building Regulations is to
ensure the health and safety of people in or about
the building. The main requirements are:
Fig 19: Twin skinned system with sound absorbing

liner
a) To provide a safe means of escape for the

building occupants by preventing internal fire
spread.
b) To prevent the spread of fire to neighbouring
property.
c) To prevent an external fire from setting fire to
the building.
d) To provide access for the Fire Brigade.
Generally metal roof cladding has to limit the
spread of fire on its internal liner face, prevent the
spread of fire through any cavity, and resist the
spread and penetration of fire on its weathersheet
side. Roofs do not usually need to provide any
period of fire resistance.
European Standard test methods have now
been published, and it is now possible to claim
compliance with Approved Document B using
either the original BS 476 tests or the new
European tests.
7.2 Reaction to fire

The Surface Spread of Flame performance of the
internal surfaces of cladding sheets is determined
by testing to BS476 Part 7, giving classifications
of Class 1, 2, 3 & 4. Profiled liner sheets generally
achieve Class 1, the best rating. The sheets will
also achieve a rating of I<12 and i1<6 in the BS476
Part 6 Fire Propagation test. The combination
16
Structural performance
of these two results means that liner sheets can

be designated Class O according to the Building
Regulations, and their use is unrestricted.
Alternatively, the reaction to fire classification can
be determined using the Single Burning Item (SBI)
test BS EN 13823 and the classification to BS
EN 13501-1. Profiled steel liner with 25 micron
polyester coating achieves a classification A1,
which is the best classification, and means use of
the liners is unrestricted.
8.1
Roof cladding systems and their fixings must be

strong enough to withstand the worst combinations
of wind, snow, imposed and dead loads calculated
in accordance with BS6399 see Fig 20.
7.3 External surface

External surfaces of roof cladding must
demonstrate adequate resistance to the spread
and penetration of fire from outside. This is
tested according to BS476 Part 3 and given
classifications of AA, AB etc through to DD. The
first letter denotes the rate of penetration through
the construction, A being the best. The second
letter refers to the spread of flame, and again A
is the best. The classification is accompanied by
EXT for external, S for sloping or F for flat. Profiled
cladding generally achieves the top rating EXT.SAA
or EXT.FAA.
There is no equivalent European classification for
the external fire performance of roofs in Approved
Document B (2003)
Load case (1)
Load factors (2)
Dead + imposed
Dead + snow drift
Dead + wind
Dead wind
1.4 Wd + 1.6 Wi
1.4 Wd + 1.05 Wsnow
1.4 Wd + 1.4 Wind
1.0Wd 1.4 Wind
Attachment(3)
1.0Wd 2.0 Wind
Notes:
1. Wd = deadload
Wi = imposed load (BS6399:Part 3)
Wsnow = snowdrift load (BS6399:Part 3)
Wind = wind load (BS6399:Part 2)
2. These load factors are mostly from BS5950:
Part 5 and are also adopted in BS5427. They
apply to the metal profile.
3. Attachment refers to the fixing assembly
(fasteners or clips). A minimum factor of 2
should be used and may be increased for timber
and other non-steel substances.
Fig 20: Load factors
7.4 Cavity barriers
There are two other special load cases for roofs:
The regulations require that the size of all hidden

cavities is restricted by cavity barriers to prevent
the unseen spread of fire. However, according
to B3 10.11g, cavity barriers are not required
in double profiled metal skin roof constructions
provided the surfaces of the insulation have
a surface spread of flame of Class O or 1, or
European Class C-s3, d2 or better, and make
contact with the inner and outer sheets.
7.5 Building insurance

Typical twin metal skin roof constructions, which
are insulated with mineral fibre (glass or rock), are
considered to be non-combustible by insurance
companies, and do not create any particular
hazard in relation to fire. No type approvals, such
as LPC, are normally required.
17
Design loading
Foot traffic:
For many roof constructions point loading due
to foot traffic is one of the critical load cases.
The minimum thicknesses specified in section
2 are generally required to enable the roof to
withstand foot traffic during assembly, but even
these are not immune from damage, if care is
not taken. Metal roof cladding is normally only
designed for cleaning and maintenance loading.
If regular access is required special walkways
should be provided. The appearance of some
roofs, particularly if made of aluminium, may be
impaired by excessive foot traffic.
Impact loading Non fragility:
When people walk on roofs during construction

or to carry out maintenance, there is always
a risk of falling over, and this can cause an
impact load on the roof. For the safety of the
individuals, the roof construction must be able
to withstand this loading without failure, and be
classed as non fragile.
The non fragility of profiled sheet roof
constructions is determined using the method
in ACR[M]001:2000. The test involves
dropping a 45kg sand bag from 1.2m onto a
sample of the construction, built on a special
test frame. Provided the bag is retained on
the construction, no matter where the bag is
dropped, the sample can be classed as non
fragile.
A classification system A, B, C, is used to show
how many impacts the sample will withstand
and how much damage is caused:
Class C is one impact, with damage
Class B is two impacts, with damage
Class A is two impacts, with no damage
For the whole of a particular roof to be classed
as non fragile, all the various elements, such
as roof sheets and rooflights, and the junctions
between the elements, must be non fragile.
This must include any special details on the
roof, such as hips, curves, and varying purlin
centres.
The performance depends on the assembly of
components, and not just the sheet material,
so details at supports such as fasteners are
normally important. Correctly assembled
profiled steel outer roof sheets with a thickness
of 0.7mm would normally be expected to
achieve Class B, either as single skin or as
part of a double skin system. Correctly fixed
profiled liner can also be classed as non fragile,
which can be an advantage during construction
and maintenance, but because the material is
only typically 0.4mm thick, the construction is
much more sensitive to correct fixing details

and correct installation. The manufacturers of
the individual roofing elements and systems
should provide non fragile specifications for
their products.
8.2 Load span tables

Profiled metal cladding manufacturers all provide
load span tables for their products to enable the
building design engineer to select suitable purlin
spacings to accommodate the design loadings
calculated above. Typically the spacing would be
1.8m, though this may be reduced in valleys or
behind parapets where high snowdrift loadings
can occur, or at eaves, verges and corners,
where there may be high local wind suction loads.
Additional fasteners may be required in these
areas, to withstand the high suction loads. The
normal maximum span for lightly profiled liner
sheets is 1.8m.
8.3 Spacer systems

The spacer system must be strong enough to
transfer all loads acting on the weathersheet into
the building structure, while maintaining the cavity
for the insulation. There should not be excessive
deflection particularly under foot traffic loads.
The various spacer systems described in section
2 have different fixing arrangements but in all
cases there must be sufficient fasteners to resist
the loads applied. Wind suction is often the
critical load case. Note that pull-out strength of a
fastener securing the spacer system depends on
the thickness and grade of the purlin to which it is
fixed. Thicker material, and higher yield strength
give increased pull-out strength.
8.4 Lateral restraint

When fixed correctly, profiled metal roof cladding
systems assist in the design of the framework by
providing a measure of restraint to the top flange
of the purlin. Safe working loads for purlins are
based on the assumption that the sheet profile and
fastener system employed will provide full lateral
restraint.
Experience has shown that 0.4mm steel (or
thicker) liner sheets attached at a maximum of
18
Durability
500mm centres using 5.5mm diameter fasteners

generally provide sufficient restraint to light gauge
purlins. Some 0.7mm thick aluminium liner profiles
of certain alloy grades can give lateral restraint and
the manufacturers guidance should be sought.
Perforated liner sheets used in acoustic absorption
constructions may not be strong enough to provide
sufficient restraint, depending on metal thickness,
profile and the perforation pattern. Each case
should be considered carefully.
It is the responsibility of the cladding contractor to

ensure that the correct fastener system is used
as recommended by the cladding or fastener
manufacturer.
9.1 Introduction
Durability is the ability of a building and its parts
to perform its required function over a period
of time (see BS7543). Virtually all materials will
change physically when subjected to UV radiation,
moisture and atmospheric pollution, and this will
affect their performance. The designer must
therefore ensure not only that the materials and
details used are suitable initially but also that they
will have a satisfactory life, given the necessary
maintenance.
9.2 Materials
The materials selected for the roof can have a
significant effect on its durability and the amount of
maintenance that will be necessary during its life.
The components which are exposed to the weather
are particularly important.
The type of sheeting material, coating and colour
must all be considered. The performance might
also depend on the shape and orientation of the
building and the environment. Generally, light
coloured coatings are preferable because they do
not absorb as much sunlight as dark colours, and
they are therefore cooler. This means they tend to
have the best life and they optimise the thermal
performance of the roof.
The table in Fig 21 gives an indication of the life
of some coated sheets on a typical 5 roof slope,
in an inland, non-polluted environment. The
life-in-years shown concern the appearance
and the condition of the coating and it can be
extended by repainting. The data has been taken
from manufacturers literature and is for general
guidance only.
Material
Coating
Life-in-years
Steel
Plastisol - light
Plastisol - dark
Pvf2
Multicoat
23
10
15
20
Aluminium
Pvf2
ARS
20
15
Fig 21: Expected life of sheets with various

coatings
19
Note that failure to repaint aluminium will not

significantly affect the ultimate life of the material.
More detailed information can be obtained from the
individual manufacturers.
Rooflights are also subject to gradual deterioration,

which will cause fading and embrittlement. PVC
is particularly susceptible. These changes can be
minimised by careful attention to detail and regular
cleaning and discussion should take place with the
manufacturer regarding life span. Replacement
may be anticipated during the life of the building.
Both plated carbon steel and stainless steel
fasteners are available. In most situations involving
coated steel cladding, plated steel fasteners
provide acceptable performance as long as their
heads are protected from the weather. Integral
plastic heads are more reliable than push on
caps and are preferable. Stainless steel fasteners
can be used for improved durability and must be
used when fixing aluminium sheets, to prevent bimetallic corrosion.
with high humidity, and the roof cladding has been

constructed correctly with an effective vapour
control layer and ventilation (where appropriate),
the standard materials and coatings will be
satisfactory.
9.4 Maintenance
The coating life shown above, and therefore the
durability of the roof, is always dependent on
regular maintenance. This will involve inspection,
removal of debris, cleaning and repair of any
damage found. Gutters are likely to require the
most frequent attention because debris tends to
collect in them and can restrict their capacity, whilst
increasing the potential for corrosion.
The durability of sealants and fillers is also an

important issue, for the long term performance of
the building. Various grades of these materials are
available, and some are more durable than others.
They should be specified carefully to ensure their
performance will be consistent with the other
components in the roof, as most are built into the
construction and are very difficult to replace.
9.3 Design details

The materials chosen for the roof must be
assembled correctly in order to achieve the
maximum durability. Avoiding water and dirt traps
by ensuring satisfactory slopes and end laps are
particularly important. For maximum durability,
all exposed cut edges of steel outer sheets and
flashings should be painted immediately after
installation.
The life expectancy of materials inside the
construction such as spacers, insulation, fasteners,
sealants and the reverse side of cladding and liner
sheets must also be considered. Provided the
building does not have an internal environment
20
Sustainability
10.1 Sustainable construction
Construction and the built environment are

fundamental to the health and well being of
society, consequently they have been particularly
highlighted as sectors where government and
legislators would like to achieve significant
improvements. Sustainable construction is about
achieving a viable balance between economic
competitiveness, social benefit and environmental
impact. In essence sustainable development has
as its goal the following objectives:
Maintaining high and stable levels of economic

growth.
Achieving social progress.
Effectively protecting the environment from

adverse impact.
Seeking a prudent use of natural resources (by

encouraging recycling and reducing waste).
All of the above factors need to be addressed for

construction to become sustainable. As one driver
for this, Building Regulations and legislation are
requiring that the minimum performance standards
are improved, and initiatives like Rethinking
Construction are working to drive change
throughout the industry.
10.2 Life Cycle Assessment

There is increasing concern about the affect of all
buildings on the environment, in terms of:
Long term global climate change because of

carbon based energy use.
Depletion of earths non-renewable resources.
The immediate local impacts caused by, for

example, release of toxic chemicals during
construction.
To properly evaluate the environmental impact

of different design decisions a cradle to grave
assessment is needed where all of the processes
from material extraction, product manufacture,
installation, maintenance and finally removal
and disposal need to be accounted for. Such
21
assessments are usually referred to as Life Cycle

Assessments, and are typically time consuming
and onerous to undertake. They are not included
directly in Building Regulations at present and there
are few direct financial incentives to follow them.
However, increasing concern about climate change,
the cost benefits in terms of reduced energy
consumption, and the use of recycled materials
and the risks of companies being sued due to real
or perceived health problems affecting employees
or the occupants of neighbouring buildings are
combining to make these issues increasingly
relevant to building designers and owners.
A set of generic life cycle assessments for typical
UK constructions has been published in the
Green Guide to Specification produced by BRE
and Oxford Brookes University. This document
assesses each building type in terms of its
environmental impact on:
Climate change.
Fossil fuel depletion.
Ozone depletion.
Human toxicity to air and water.
Acid deposition (i.e. the emission of gasses that

contribute to acid rain).
Ecotoxicity (that is, the emission of substances,

usually heavy metals, that impact on
neighbouring ecosystems).
Eutrophication (that is, the production of

nitrates and phosphates, which cause
excessive algal growth and consequent oxygen
depletion in water courses).
Summer smog.
Mineral extraction.
Each of these is awarded a grading from A (best)

to C (worst) and an overall grade is given to the
building type. Industrial metal buildings and roofs
achieve overall A ratings and score highly for most
of the above impacts. The high sustainability
rating of these products reflects the particular
advantage of using a comparatively low mass

roofing system with less material resource input
than other commercial systems.
Generally, metal cladding systems have relatively
good sustainability credentials as a result of
the opportunities for recycling. Although metal
sheeting systems would not be routinely reused
at the end of a roof systems life, the material
itself can be processed and recycled for other
applications. Similarly, the materials used for
the manufacture of the metallic components can
contain some recycled material. Both of these
factors reduce the environmental impact of metal
cladding systems, and the growing recycling
industry will help to continue to reduce this in future.
ensure compliance with environmental laws

and regulations;
seek certification of its environmental

management system by an external third party
organisation
Awareness of the issues in these documents

can help clients meet the increasingly complex
demands in a world where environmental concerns
are growing in importance.
Correctly specified metal cladding and roofing

systems competently installed should have good
thermal performance and achieve a consistently
good air tightness standard. This will ensure
that the heat loss through the structure will be
consistent with that set by the designer, rather than
being reliant on the performance of site workers
which can often let masonry construction down.
10.3 ISO 14001

Increasingly organisations are adopting ISO 14001
in their management procedures which specifies
the actual requirements for an environmental
management system. It applies to those
environmental aspects which the organisation
has control over and this extends to the design,
procurement and maintenance of new buildings.
As a result, such organisations are requiring that
the design team demonstrates and justifies the
performance of a proposed development, and
where appropriate establish an Environmental
Plan to ensure that the impacts of the construction
process are minimized. ISO 14001 is applicable to
any organisation that wishes to:
implement, maintain and improve an

environmental management system;
assure itself of its conformance with its own

stated environmental policy (those policy
commitments of course must be made);
22
Construction details and

accessories
11.1 Junction details
The typical details shown in this section
illustrate the general arrangement at various
junctions. In each case, the value and f value
associated with thermal bridging are shown.
(See section 4). Proprietary systems may have
particular requirements and the manufacturers
recommendations should always be followed.
All other junctions and details for a particular

construction should be designed adopting the
same principles, ensuring continuity of the
weatherproofing, vapour/air control layer, and
thermal insulation.
11.1.1 Ridge
Provided that the insulation is continued over the
ridge to provide continuous coverage, as shown in
Fig 22, this will be a minimal thermal bridge.
Fig 23: Eaves typically fmin = 0.95 = 0.01 W/mK

11.1.3 Verge
The thermal bridge can be minimised by taking the
roof liner back to the wall liner, so that it does not
cross the wall insulation, and ensuring that any
void between the wall and roof insulation is fully
filled with insulation as shown in Fig 24.
Fig 22: Roof typically fmin = 0.91 = 0.01 W/mK

11.1.2 Eaves
The thermal bridge can be minimised by taking the
roof liner back to the wall liner, so that it does not
cross the wall insulation, and ensuring that any
void between the wall and roof insulation is fully
filled with insulation as shown in Fig 23.
Fig 24: Verge typically fmin = 0.95 = 0.02 W/mK

11.1.4. Valley gutter
This detail can cause a very severe thermal bridge
if the metal outer layer of the gutter top and roof
liner cut across the gutter insulation.
Making the gutter liner more robust and replacing
part or all of the gutter outer with a lower
conductivity material such as plastic where it cuts
across the insulation will reduce the thermal bridge;
if the roof liner is stopped short as well so that the
23
insulation layer is continuous, the thermal bridge

can be largely eliminated (Fig 25)
sleeving for use with profiled cladding. These

should always be positioned at the profile crown
as shown in Fig 26 to ensure they do not create
a dam across a trough. If this cannot be achieved,
an apron flashing should be fitted on top of the
profiled sheets upslope to the ridge to prevent
ponding behind the penetration, or a site applied
GRP flashing could be formed. (See 11.5). The
manufacturers recommendations should always
be followed.
Fig 25: Valley gutter with thermal break across the

gutter insulation
Typically fmin = 0.95 = 0.17 W/mK
11.2 Rooflights
Rooflights are used in many industrial and
commercial buildings. Typically a rooflight area of
approximately 10% of the total roof area is used.
Great care should be taken in their specification
and installation, and the manufacturers guidance
should always be followed. See also MCRMA
technical paper No 1 Recommended good practice
for daylighting in metal clad buildings.
11.3 Roof drainage

The roof drainage system is an important aspect of
the overall roof design. This is particularly the case
for parapet and valley gutters, which are inside
the building line and are effectively part of the
roof. Any overflow or leaks into the building would
be unacceptable. Eaves gutters are outside the
building and their design is less critical.
The roof drainage design is based on BS EN
12056-3:2000, Gravity drainage systems inside
buildings roof drainage, layout and calculation.
The design process and the correct selection of
materials can be complex and it is recommended
that the designer consults one of the companies
that specialises in the design and manufacture of
roof drainage systems.
11.4 Small penetrations

Small diameter penetrations such as flues
and other service pipes can be successfully
weatherproofed using proprietary or purpose-made
Fig 26: Typical neoprene rubber proprietary pipe

flashing
11.5 Large penetrations

Large penetrations such as fans, smoke vents
etc. often require additional structural support
between purlins. The penetrations should ideally
be placed at or close to the ridge where they can
be waterproofed more easily. If used downslope,
a special soaker sheet has to be used to divert
the flow of rainwater around the sides of the
penetrations. The accessory must then be fixed
and weathered to the upstand.
These soakers are customised to match
the weathersheet profile and the size of the
penetration. They are typically fabricated from GRP,
aluminium or painted galvanised steel. Ideally they
should be fitted during cladding when normal end
and side lapping details can be used. Retrofitting is
also possible but might involve using cover sheets
or apron flashings back to the ridge. These can be
unreliable, unsightly and expensive.
24
Most flashings used on roofs are open and can

be lapped, typically including stitching fasteners
at a maximum spacing of 100mm, and sealant on
the weatherside of the fasteners. Closed sections,
such as some eaves gutters, use butt straps
behind the joint. These should be at least 150mm
long. For detailed guidance see MCRMA technical
paper No. 11 Flashings for metal roof and wall
cladding: design detailing and installation guide.
Fig 27: Large penetration

Site applied GRP (or similar liquid applied system)
can provide a good solution for all sizes and
shapes of penetration. This must be carried out by
specialist sub contractors to ensure satisfactory
adhesion to the profiled weather sheeting. Contact
MCRMA members for further details.
Whenever a penetration is fitted to the roof it is
essential that the vapour control layer, insulation
and breather membrane (if fitted) are correctly
detailed and constructed.
11.6 Flashings
Flashings are normally manufactured in the same
material and thickness as the cladding, at least
0.7mm for steel and 0.9mm for aluminium. Where
the leg length of a flashing exceeds approximately
200mm, it will be difficult to maintain a flat
appearance and it is advisable to introduce a
bend or stiffener to straighten and strengthen the
material. See examples in section 11.1)
Exposed edges should be stiffened using one of
the details shown in Fig 28.
Lock roll
Welt
Stiffened edge
Fig 28
25
Further typical details are available on the

MCRMA web site at www.mcrma.co.uk
Site work
12.1 General
Metal roof cladding should be fully detailed on

cladding drawings for each individual building.
The drawings should include all the necessary
dimensions, components, fasteners, seals etc.
to enable the sheeters to install the cladding in
accordance with the designers requirements,
in order to achieve the specified performance.
Responsible supervision and regular inspection is
essential to ensure structural integrity, satisfactory
performance, acceptable appearance and quality
in general.
Deviations in steel frame construction, rafters
and purlins etc. can often be greater than those
acceptable for the cladding material, especially at
critical bearing positions such as end laps, or at
junctions.
Stacks should be carefully positioned and stored

on site to prevent damage or deterioration.
Particular attention should be paid to the following
points:
a) Position away from vehicle and pedestrian
routes
b) Site on bearers on firm flat ground
c) Cover and ventilate
d) Ensure labelling is intact
Some sheets and panels are supplied with a
protective plastic film on the weatherface to help
prevent minor damage to the coating. This must
be removed as soon as possible after the cladding
has been installed because if it is left in place for
long periods the film will become very difficult to
remove. Individual manufacturers instructions
should always be followed.
The steel framework should be surveyed prior to

handover to the roofing contractor. Any deviations
in line, level and plumb must be acknowledged by
all parties and the necessary adjustments made to
suit the cladding requirements before starting the
installation.
12.2 Transport, handling and storage

Loading and off-loading packs by crane or fork-lift
should be carried out with care to avoid damage to
the outermost sheets or panels in the pack. Never
off-load with chains, use only wide soft slings for
lifting. Use lifting beams, if recommended by the
manufacturer
Fig 30: Storage of materials
12.3 Site cutting

Site cutting is generally avoided by the use of
sheets cut to length in the factory. However,
where site cutting is unavoidable nibblers and
reciprocating saws (jig saws) should be used.
Abrasive wheel cutters must not be used because
they generate heat and will damage the coating.
For optimum durability site cut edges, eaves and
end laps of steel sheets should be painted.
12.4 Health and safety
Fig 29: Slings used for lifting
As in all building work, good safety standards

are essential to prevent accidents. In accordance
with the Health and Safety at Work Act and the
Construction (Design and Management) or CDM
Regulations, the building should now be designed
with safety in mind, not only for the construction
26
Inspection and
maintenance
period itself but also throughout the normal life of

the building. This must include considering the
safety of people involved in maintenance, repair
and even demolition. It might mean providing
permanent access to the roof via a fixed ladder
and hatch, walkways and parapets, for example.
Construction of the roof is one of the most
hazardous operations because of the potential for
falls or material dropping onto people below. The
contractors must plan and document a safe system
of work before starting construction. This would
take the fragility of the cladding materials into
account, but initially, safety nets are normally used.
Whilst fully fixed metal roof sheeting is regarded as
non fragile, rooflights and profiled metal liners must
be treated with more care. (See section 8.1)
In addition to the basic safe system of working
the following specific precautions should be taken
when using metal cladding:
a. Take care when handling sheets to avoid cuts
from the edges of the sheets. Wear gloves to
protect hands.
b. Take normal precautions when lifting heavy
awkward objects to avoid lifting injuries,
in accordance with the Manual Handling
Operations Regulations.
c. When cutting wear goggles and dust masks.
The strength and visibility of some rooflights can
deteriorate during the normal life of a building
and present a hazard to maintenance workers,
particularly if they have not been trained. The
rooflights are usually fixed with fasteners with red
plastic heads, to highlight their positions.
This sort of information must now be detailed in
a safety file prepared by the planning supervisor
(using information provided by the designer) and
passed on to the client at handover.
If in doubt about safety issues, guidance can be
obtained from the construction section of the local
Health and Safety Executive.
27
Metal roof cladding is designed and manufactured

to give many years of reliable service, but to
achieve this, a regular inspection and maintenance
programme is required.
Roof cladding and gutters should be inspected
at regular intervals and any deposits such as
leaves, soil or litter must be removed. Any areas
of corrosion or damage should be repaired in
accordance with the manufacturers maintenance
manual.
Roof traffic should be kept to a minimum and must
be restricted to authorised trained personnel only,
using appropriate safety measures.
References
1.
2.
3.
4.
5.
6.
7.
8.
9.
BS EN ISO 6946 : 1997, Building components

and building elements Thermal resistance
and thermal transmittance Calculation
method.
CIBSE Guide A3, Thermal properties of
building structures, CIBSE 1999.
BS EN ISO 10211-1: 1996, Thermal bridges in
building construction - Heat flows and surface
temperatures, Part 1. General calculation
methods.
BRE Information Paper IP 10/02, Metal
cladding : assessing the thermal performance
of built-up systems which use Z spacers.
SCI Technical Information Sheet, P312 2002,
Assessing thermal performance of built-up
metal roof and cladding systems using rail and
bracket spacers.
BRE Report BR443, Conventions for
calculating U-values, BRE 2002.
BRE IP 17/01, Assessing the effect of thermal
bridging at junctions and around openings,
BRE August 2001.
MCRMA technical paper No. 14, Guidance
for the design of metal roofing and cladding to
comply with Approved Document L2 : 2001.
BS EN ISO 13788:2001, Hygrothermal
performance of building components
and building elements - Internal surface
temperature to avoid critical surface humidity
and interstitial condensation Calculation
methods.
MCRMA technical papers
No 1 Recommended good practice for daylighting

in metal clad buildings
No 2 Curved sheeting manual
No 3 Secret fix roofing design guide
No 4 Fire and external steel-clad walls: guidance
notes to the revised Building Regulations,
1992 (out of print)
No 5 Metal wall cladding design guide
No 6 Profiled metal roofing design guide
No 7 Fire design of steel sheet clad external
walls for building: construction performance
standards and design
No 8 Acoustic design guide for metal roof and
wall cladding
No 9 Composite roof and wall cladding design
guide
No 10 Profiled metal cladding for roofs and
walls: guidance notes on revised Building
Regulations 1995 parts L and F (out of
print)
No 11 Flashings for metal roof and wall cladding:
design, detailing and installation guide
No 12 Fasteners for metal roof and wall cladding:
design, detailing and installation guide
No 13 Composite slabs and beams using steel
decking: best practice for design and
construction
No 14 Guidance for the design of metal roofing
and cladding to comply with Approved
Document L2: 2001
No 15 New Applications: composite construction
No 16 Guidance for the effective sealing of end lap
details in metal roofing constructions
Other publications
The Complete Package CDROM
Manufacturing tolerances for profiled metal roof
and wall cladding
CladSafe latent defects insurance scheme: basic
guide
Liability
Whilst the information contained in this design guide is believed
to be correct at the time of going to press, the Metal Cladding and
Roofing Manufacturers Association and its member companies
cannot be held responsible for any errors or inaccuracies and, in
particular, the specification of any application must be checked
with the individual manufacturer concerned for a given installation.
Composite flooring systems: sustainable

construction solutions
Please note: Publications can be downloaded
from the MCRMA web site at www.mcrma.co.uk
The diagrams of typical constructions in this publication are

illustrative only.
28
18 MERE FARM ROAD

PRENTON . WIRRAL
CHESHIRE CH43 9TT
TELEPHONE: 0151 652 3846
FACSIMILE: 0151 653 4080
mcrma@compuserve.com
www.mcrma.co.uk
designed by Seventhplanet printed by Hutson Fastprint Limited
THE METAL CLADDING & ROOFING MANUFACTURERS ASSOCIATION LIMITED
12.00
incl. P&P

Profiled Metal Roofing The Metal Cladding & Roofing Manufacturers Association Limited PDF

Uploaded by

Profiled Metal Roofing The Metal Cladding & Roofing Manufacturers Association Limited PDF

Uploaded by

A single copy of this document is licensed to

Licensed copy from CIS: MACE, MACE, 29/05/2016, Uncontrolled Copy.

This is an uncontrolled copy. Ensure use of the

MCRMA Technical Paper No. 6

Licensed copy from CIS: MACE, MACE, 29/05/2016, Uncontrolled Copy.