Scribd
Upload
327 views2 pages

Pic pg2c

Serial PIC programmer board

Uploaded by

api-3697567
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
327 views2 pages

Pic pg2c

Serial PIC programmer board

Uploaded by

api-3697567
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 2

PIC-PG2C SERIAL PORT

PIC MICROCONTROLLER PROGRAMMER

Features: is connected to VCC and you attempt to do ICSP


PIC-PG2C is low cost serial port programmer for 8, programming you may destroy PIC-PG2
18, 28 and 40 pin PIC microcontrollers. The programmer.
programmer doesn’t need external power supply
and takes all necessary signals and power from ICPROG installation:
RS232 port. Setup the Hardware settings as "JDM programmer"
with direct IO access if you are using Windows 95/98
and Windows API if you are working with Windows
Programming: NT.
PIC-PG2C works with ICPROG software, written Please note that the programmer is powered from
by Bonny Gijzen. The latest release of ICPROG the RS232 port, so before you put or take off your
device disconnect the programmer from the RS232
may be download for free from port!
http://www.icprog.com
The programmer can be used to program I2C RS232 interface:
serial EEPROM memory devices from 24Cxx Your RS232 cable must provide the following
series. signals for properly operation of PIC-PG2: Tx,
Rx, CTS, DTR, RTS and GND.
ICD/ICSP connector layout:
The ICD/ICSP connector is 6 pin with 0,1" step. Supported devices:
The PIN.1 is marked with square pad on bottom Current supported devices by ICPROG are:
and arrow on top. ICSP signals are: 1- MCLR, 2- 12C508, 12C508A, 12C509, 12C509A,
VDD, 3- VSS/GND, 4- PGD/RB7, 5- PGC/RB6, 12CE518, 12CE519, 12C671, 12C672,
6- PGM/RB3. 12CE673, 12CE674, 16C61, 16C62A, 16C62B,
16C63, 16C63A, 16C64A, 16C65A, 16C65B,
16C66, 16C67, 16C71, 16C72, 16C72A,
16C73A, 16C73B, 16C74A, 16C76, 16C77,
16C84, 16F83, 16F84, 16F84A, 16C505,
16C620, 16C621, 16C622, 16C622A, 16F627,
16F628, 16C715, 16F870, 16F871, 16F872,
16F873, 16F874, 16F876, 16F877, 16C923,
16C924
ICSP programming:
Please note that in your target circuit MCLR
Ordering codes:
should be not directly connected to VCC, as PIC-PG2C - assembled and tested
programmer try to rise MCLR to 13VDC to enter
in programming mode. If MCRL on target board

Copyright(c) 2003, OLIMEX Ltd, All rights reserved.


Development boards for PIC, AVR and MSP430 microcontrollers http://www.olimex.com/dev

You might also like