BFPA LIBRARY OF STANDARDS

FP010007 25 October 2010

BFPA LIBRARY OF STANDARDS

CONTENTS
Page

British standards prefix BS European standards implemented as British standards (mandatory) prefix BS EN International standards implemented as European and British standards prefix BS EN ISO International standards implemented as British standards prefix BS ISO International standards prefix ISO

3-4 5 6-8 9-15 16-18

KEY = Technical Committee responsible 1 3 4 5 6 7 8 9 16 TCs Accumulators (TC 1) Cylinders (TC 3) Connectors and associated components (TC 4) Control components (TC 5) Contamination control (TC 6) Seals (TC 7) Product testing (TC 8) Systems (TC 9) Fluids (TC 16) All technical committees

FP010007 25 October 2010

BRITISH STANDARDS INSTITUTE

British standards
Number BS 3G 100-2.3.13:1973 Title Specification for general requirements for equipment for use in aircraft All equipment Environmental conditions Resistance to fire in designated fire zones Controlled storage of vulcanised rubbers for use in aerospace applications Specification for steel pipes and joints for hydraulic purposes Physical testing of rubber Guide to the selection and use of methods of test for rubber Physical testing of rubber Determination of density Physical testing of rubber Determination of abrasion resistance Dimensions of toroidal sealing rings O-rings and their housings inch series Pipe threads for tubes and fittings where pressure tight joints are not made on the threads (metric dimensions) Metallic tube connectors for fluid power and general use Part 1: Split collet compression fittings Compression couplings for tubes Part 4: Specification for type test requirements Specification for metric dimensions of toroidal sealing rings (O-rings) and their housings Drawing practice for engineering diagrams Methods of test for hoses Part 1: Measurement of dimensions Methods of test for hoses Part 2: Hydraulic pressure tests Methods of test for rubber and plastics hoses and hose assemblies Part 100: General introduction Methods of test for rubber and plastics hoses and hose assemblies Part 102.1: Hydraulic pressure tests Hydrostatic tests Methods of test for rubber and plastics hoses and hose assemblies Part 102.3 Hydraulic pressure tests Determination of volumetric expansion of fuel-dispensing pump hoses Methods of test for rubber and plastics hoses and hose assemblies Part 102.4 Hydraulic pressure tests Determination of volumetric expansion of hydraulic hoses Methods of test for rubber and plastics hoses and hose assemblies Part 102.8 Hydraulic pressure tests Pressure impulse test for rigid helix reinforced thermoplastics hoses Methods of test for rubber and plastics hoses and hose assemblies Part 102.10 Hydraulic pressure tests Hydrostatic tests for oil suction and discharge hose Methods of test for rubber and plastics hoses and hose assemblies Part 103.6 Physical tests - Determination of ignitability of lining Methods of test for rubber and plastics hoses and hose assemblies Part 103.7 Physical tests Determination of fracture resistance of rigid polymer helical reinforcement in thermoplastics hoses Methods of test for rubber and plastics hoses and hose assemblies Part 103.13 Physical tests Determination of resistance to fire Rubber and plastics hoses and hose assemblies Part 106.2 Environmental tests General requirements for high temperature ageing tests Key 4

BS 4F 68:2002 BS 778:1966 BS 903-1:1995 BS 903-A1:1996+ Corr 1:1996 BS 903-A9:1988 BS 1806:1989 BS 2779:1986 BS 4368-1:1998 BS 4368-4:1984 BS 4518:1982 BS 5070:1974 BS 5173-1:1976 BS 5173-2:1976 BS 5173-100:1992 BS 5173-102.1:1991 BS 5173-102.3:1988

4 4 4 4 4 7 4 4 4 7 TCs 4 4 4 4 4

BS 5173-102.4:1990

BS 5173-102.8:1987

BS 5173-102.10:1990

BS 5173-103.6:1990 BS 5173-103.7:1991

4 4

BS 5173-103.13:1994 BS 5173-106.2:1990

4 4

FP010007 25 October 2010

BRITISH STANDARDS INSTITUTE

British standards continued
Number BS 5200:1997 BS 5244:1986 BS 5344:1976 BS 5380:1984 BS 5540-3:1978 BS 5540-6:1990 Title Fluid Power Systems specification for dimensions of hydraulic connectors and adaptors Application, storage and life expiry of hydraulic rubber hoses and hose assemblies Methods for acceptance tests for rotary and percussive pneumatic tools Specification for hydraulic port and stud coupling using O-ring sealing and G-series fastening threads. Evaluating particulate contamination of hydraulic fluids Part 3: Methods of bottling fluid samples Evaluating particulate contamination of hydraulic fluids Part 6: Method of calibrating liquid automatic particle-count instruments (using mono-sized latex spheres) Guide for commissioning, operation and maintenance of hydraulic turbines Dimensions for basic features of fluid power cylinders Specification for moulded transparent polycarbonate bowls used in compressed air filters and lubricators Hydraulic fluid power filter elements Part 2: Methods of test to verify structural integrity HFP Filter elements Part 3: Specification for marking Mounting dimensions for single rod double acting hydraulic cylinders Part 4: Specification for 63 bar series including associated components Specification for three-pin plug connectors for electrically controlled fluid power equipment Specification for design and construction of reservoirs used in hydraulic fluid power systems Staple type connectors for hydraulic fluid power applications Guide to installation and use of valves Guide for prevention of leaks from hydraulic fluid power systems Specification for precision finished seamless cold-drawn low carbon steel tubes for use in hydraulic fluid power systems Specification for interface dimensions of flat face O-ring seal hydraulic couplings Care and handling of seals for fluid power applications Guide HFP Monitoring the level of particulate contamination Comparison membrane technique Key 4 4 TCs 4 6 6

BS 5671:1979 BS 5755:1986 BS 6005:1997 BS 6275-2:1984 BS 6275-3:1988 BS 6331-4:1985 BS 6361:1988 BS 6525:1984 BS 6537:1984 BS 6683:1985 BS 7388:1991 BS 7416:1991 BS 7417:1991 BS 7714:2005 BS 8465:2010

9 3 5 6 6 3 5 9 4 5 9 4 4 7 6

FP010007 25 October 2010

CEN - European Committee for Standardisation

European standards implemented as British standards (mandatory)
Number BS EN 693:2001 BS EN 853:1997 +A1:2008 BS EN 854:1997 BS EN 855:1997 BS EN 856:1997 BS EN 857:1997 BS EN 954-1:1997 BS EN 982:1996 +A1:2008 BS EN 983:1996 +A1:2008 BS EN 1037:1996 BS EN 1050:1997 BS EN 1088+A1 BS EN 1360:2005 BS EN 1765:1998 BS EN 10226-1:2004 Title Machine tools - Safety - Hydraulic presses Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type Specification Rubber hoses and hose assemblies Textile reinforced hydraulic type Specification Plastics hoses and hose assemblies - Thermoplastics textile reinforced hydraulic type - Specification Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced by hydraulic type - Specification Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification Safety of machinery Safety related parts of control systems Part 1: General principles for design Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics Safety of machinery Prevention of unexpected start-up Safety of machinery Principles for risk assessment Safety of machinery - Interlocking devices associated with guards Principles for design and selection Rubber and plastic hoses and hose assemblies for measure fuel dispensing systems Specification Rubber hose assemblies for oil suction and discharge services Specification for the assemblies Pipe threads where pressure tight joins are made on the threads Part 1: Taper external threads and parallel internal threads Dimensions, tolerances and designation Pipe threads where pressure tight joins are made on the threads Part 2: Taper external and internal threads Dimensions, tolerances and designation Pipe threads where pressure tight joins are made on the threads Part 3: Verification by means of limit gauges Steel tubes for precision applications Technical delivery conditions Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems Steel wire and wire products Hose reinforcement wire Safety of machine tools - Hydraulic press brakes Gas-loaded accumulators for Fluid Power applications Fire-resistant hydraulic fluids - Guidelines for the selection of fluids and the consideration of safety, health and environment hazards Petroleum and related products - Determination of the oxidation stability and corrosivity of fire-resistant phosphate ester fluids Petroleum and related products - Determination of the hydrolytic stability of fire-resistant phosphate ester fluids Safety of machinery Electrical equipment of machines Part 1: General requirements Graphical symbols for diagram Part 2: Symbol elements, qualifying symbols and other symbols having general application Key 9 4 4 4 4 4 9 9 9 9 9 9 4 4 4

BS EN 10226-2:2005

BS EN 10226-3:2005 BS EN 10305-4:2003

4 4

BS EN 10324:2004 BS EN 12622:2001 BS EN 14359:2006 BS EN 14489:2005 BS EN 14832:2005 BS EN 14833:2005 BS EN 60204-1:2006+ A1:2009 BS EN 60617-2:1996

4 9 1 16 16 16 9 9

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION CEN - European Committee for Standardisation British Standards Institute
International standards implemented as European and British standards
Number BS EN ISO 228-1:2003 BS EN ISO 228-2:2003 BS EN ISO 1179-1:2008 Title Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation Pipe threads where pressure-tight joints are not made on the threads Part 2: Verification by means of limit gauges Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 2: Heavy-duty (S series) and light duty (L series) stud ends with elastomeric sealing (type E) Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) Geometrical product specifications (GPS) - Indication of surface texture in technical product documentation for you to review in light of ISO 6164. Rubber and plastics hoses - Minimum and maximum inside diameters and tolerances on cut lengths Rubber and plastics hoses and hose assemblies - hydrostatic testing Rubber hoses, textile-reinforced for general purpose water applications specification Rubber or plastics hoses and tubing - bending tests Rubber hoses, textile-reinforced for compressed air - specification Petroleum products - Determination and application of precision data in relation to methods of test Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 1: Procedure for mineral oils Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 3: Anhydrous procedure for synthetic hydraulic fluids Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 4: Procedure of industrial gear oils Petroleum and related products Determination of the corrosion resistance of fire-resistant hydraulic fluids Part 1: Water-containing fluids Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids Part 2: Non-aqueous fluids Plastics Determination of burning behaviour by oxygen index Part 2: Ambient temperature test Plastics Determination of burning behaviour by oxygen index Part 3: Elevated temperature test Rubber and plastics hoses and hose assemblies - Methods of measurement of dimensions of hoses and length of hose assemblies Rubber and plastics hoses Sub-ambient temperature flexibility tests Plastics hoses Textile reinforced types for compressed air applications Specification Key 4 4 4

BS EN ISO 1179-2:2008

BS EN ISO 1179-3:2008

BS EN ISO 1179-4:2008

BS EN ISO 1302:2002 BS EN ISO 1307:2008 BS EN ISO 1402:2009 BS EN ISO 1403:1997 BS EN ISO 1746:2001 BS EN ISO 2398:2008 BS EN ISO 4259:2006 BS EN ISO 4263-1:2004 BS EN ISO 4263-3:2006

TCs 4 4 4 4 4 16 16 16

BS EN ISO 4263-4:2006 BS EN ISO 4404-1:2006 BS EN ISO 4404-2:2003 BS EN ISO 4589-2:1999 BS EN ISO 4589-3:1996 BS EN ISO 4671:2007 BS EN ISO 4672:1999 BS EN ISO 5774:2008

16 16 16 4 4 4 4 4

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION CEN - European Committee for Standardisation British Standards Institute
International standards implemented as European and British standards continued
Number BS EN ISO 6149-1:2006 Title Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends Dimensions, design, test methods and requirements Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O-ring sealing Part 3: Light-duty (L series) stud ends Dimensions, design, test methods and requirements Plastics hoses, textile reinforced for general purpose water applications Specification Lubricants, industrial oils and elated products (class L) Classification Part 4: Family H (hydraulic systems) Rubber and plastics hose and hose assemblies with wire reinforcements Hydraulic impulse test with flexing Rubber or plastics hoses and hose assemblies - Hydraulic pressure impulse test without flexing Rubber hoses and hose assemblies for use in oil burners - Specification Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification Rubber and plastics hoses and hose assemblies Determination of suction resistance Rubber and plastics hoses Determination of abrasion of lining Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to design working pressure Rubber and plastics hoses Method of test for flammability Rubber and plastics hose and hose assemblies Determination of electrical resistance and conductivity Rubber and plastics hose assemblies Flexing combined with hydraulic impulse test (half-omega test) Rubber and plastics hoses Determination of adhesion between components Rubber and plastics hoses and tubing Determination of transmission of liquids through hose and tubing walls Rubber and plastics hoses and hose assemblies - Vocabulary Metallic tube connections for fluid power and general use Part 1: 24 cone connectors Rubber and plastics hoses Determination of ultra violet resistance under static conditions Corrosion tests in artificial atmospheres Salt spray tests Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 2: Stud ends with elastomeric sealing (type E) Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 3: Stud ends with metal-to-metal sealing (type B) Lubricants, industrial oils and related products (Class L) - Family H (Hydraulic systems) - Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU Key 4

BS EN ISO 6149-2:2006

BS EN ISO 6149-3:2006

BS EN ISO 6224:1997 BS EN ISO 6743-4:1999 +A1:2001 BS EN ISO 6802:2008 BS EN ISO 6803:2008 BS EN ISO 6806:1996 BS EN ISO 6808:2001 BS EN ISO 7233:1995 BS EN ISO 7662:1996 BS EN ISO 7751:1997 BS EN ISO 8030:1998 BS EN ISO 8031:2009 BS EN ISO 8032:1999 BS EN ISO 8033:2006 BS EN ISO 8308:1996 BS EN ISO 8330:2008 BS EN ISO 8434-1:2007 BS EN ISO 8580:1995 BS EN ISO 9227:2006 BS EN ISO 9974-1:2000

4 16 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 TCs 4

BS EN ISO 9974-2:2000

BS EN ISO 9974-3:2000

BS EN ISO 12922:2002

16

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION CEN - European Committee for Standardisation British Standards Institute
International standards implemented as European and British standards continued
Number BS EN ISO 13849-1: 2008 BS EN ISO 13849-2: 2008 BS EN ISO 14644-1: 1999 BS EN ISO 14935:1999 BS EN ISO 19879:2010 BS EN ISO 20763:2004 BS EN ISO 20764:2003 Title Safety of machinery - Safety-related parts of control systems Part 1: General principles for design Safety of machinery - Safety-related parts of control systems Part 2: Validation Cleanliness and associated controlled environments Part 1: Classification of air cleanliness Petroleum and related products - Determination of wick flame persistence of fire-resistant fluids Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections Petroleum and related products - Determination of anti-wear properties of hydraulic fluids - Vane pump method Petroleum and related products - Preparation of a test portion of highboiling liquids for the determination of water content - Nitrogen purge method Petroleum and related products - Determination of emulsion stability of fireresistant hydraulic fluids Part 1: Fluids in class HFAE Petroleum and related products - Determination of emulsion stability of fireresistant hydraulic fluids Part 2: Fluids in class HFB Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle Key 9 9 6 16 4 16 16

BS EN ISO 20783-1: 2003 BS EN ISO 20783-2: 2003 BS EN ISO 20844:2004

16 16 16

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards
Number BS ISO 37:2005 BS ISO 188:2007 BS ISO 815-1:2008 BS ISO 1219-2:1995 BS ISO 1436:2009+ Corr:2010 BS ISO 1817:2005 BS ISO 2781:2008 BS ISO 2941:2009 BS ISO 2942:2004 BS ISO 2943:1998 BS ISO 2944:2000 BS ISO 3019-1:2001 Title Rubber, vulcanised or thermoplastic Determination of tensile stress strain Rubber, vulcanised or thermoplastic Accelerated ageing and heat resistance tests Rubber, vulcanised or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures Fluid power systems and components Graphic symbols and circuit diagrams Part 2 Circuit diagrams Rubber hoses and hose assemblies Wire braid reinforced hydraulic types for oil or water-based fluids Specification Rubber vulcanised Determination of the effect of liquids Rubber, vulcanised or thermoplastic Determination of density HFP Filter elements Verification of collapse/burst pressure rating HFP Filter elements Verification of fabrication integrity and determination of the first bubble point HFP Filter elements Verification of material compatibility with fluids Fluid power systems and components Nominal pressures HFP Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 1: Inch series shown in metric units HFP Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 2: Metric series Fluid power systems and components Cylinders Nominal pressures Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes Fluid Power Systems - O-rings Part 2: Housing dimensions for general applications Fluid Power Systems - O-rings Part 3: Quality acceptance criteria Fluid Power Systems - O-rings Part 4: Anti-extrusion rings (back-up rings) HFP Filter elements Method for end load test HFP Filter elements Determination of resistance to flow fatigue using particulate contaminant Rubber hoses and hose assemblies Rubber covered spiral wire reinforced hydraulic types for oil or water-based fluids Specification HFP Filters Evaluation of differential pressure versus flow characteristics Rubber hoses and hose assemblies Textile reinforced hydraulic types for oil or water-based fluids - Specification HFP Determination of characteristics of motors Part 1: At constant low speed and constant pressure HFP Determination of characteristics of motors Part 2: Startability Fluid power systems and components Cylinder piston rod end types and dimensions HFP Four-port directional control valves Mounting surfaces HFP Fluids Method for coding the level of contamination by solid particles HFP Fluid Contamination Determination of particulate contamination by the counting method using an optical microscope HFP Positive displacement pumps, motors and integral transmissions Methods of testing and presenting basic steady state performance HFP Valves Determination of pressure differential/flow characteristics HFP General rules relating to systems PFP General rules relating to systems Key 4 4 4 TCs 4 4 4 6 6 6 TCs 8

BS ISO 3019-2:2001 BS ISO 3322:1985 BS ISO 3601-1:2008+ Corrigenda:2008 and 2009 BS ISO 3601-2:2008 BS ISO 3601-3:2005 BS ISO 3601-4:2008 BS ISO 3723:1976 BS ISO 3724:2007 BS ISO 3862:2009 BS ISO 3968:2001 BS ISO 4079:2009 BS ISO 4392-1:2002 BS ISO 4392-2:2002 BS ISO 4395:2009+ Corr:2010 BS ISO 4401:2005 BS ISO 4406:1999 BS ISO 4407:2002 BS ISO 4409:2007 BS ISO 4411:2008 BS ISO 4413:1998 BS ISO 4414:1998

8 3 7

7 7 7 6 6 4 6 4 8 8 3 5 6 6 8 4 9 9

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards - continued
Number BS ISO 5391:2003 BS ISO 5596:1999 BS ISO 5597:2010 BS ISO 5598:2008 BS ISO 5599-1:2001+ Corr 1 BS ISO 5599-2:2001+ A1 and Corr 1 BS ISO 5781:2000 BS ISO 5782-1:1997 BS ISO 5782-2:1997 BS ISO 6020-1:2007 BS ISO 6020-2:2006+ Corr:2008 BS ISO 6020-3:1994 BS ISO 6022:2006 BS ISO 6072:2002 BS ISO 6099:2009 BS ISO 6149-4:2006 Title Pneumatic tools and machines - Vocabulary HFP Gas-loaded accumulators with separator Ranges of pressures and volumes and characteristic quantities HFP Cylinders Dimensions and tolerances of housings for single acting piston and rod seals in reciprocating application Fluid power systems and components - Vocabulary PFP Five-port directional control valves Part 1: Mounting interface surfaces without electrical connector PFP Five-port directional control valves Part 2: Mounting interface surfaces with optional electrical connector HFP Pressure reducing valves, sequence valves, unloading valves, throttle valves and check valves Mounting surfaces PFP Compressed air filters Part 1: Main characteristics to be included in suppliers literature and product marking requirements PFP Compressed air filters Part 2: Test methods to determine the main characteristics to be included in suppliers literature HFP Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 1: Medium series HFP Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series HFP Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 3: Compact series with bores from 250 to 500mm HFP Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series HFP Compatibility between fluids and standard elastomeric materials Fluid power systems and components Cylinder Identification code for mounting dimensions and mounting types Connections for fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 4: Dimensions, design, test methods and requirements for external and internal hex port plugs HFP Flange connectors with split or one-piece flange clamps and metric or inch screws Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 HFP - Flange connectors with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 127 Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 1: Nominal dimensions and tolerances Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 2: Vocabulary Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 3: Storage, handling and installation Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 4: Performance test procedures Rotary shaft lip-type seals incorporating elastomeric sealing elements Part 5: Identification of visual imperfections Fluid power systems and components Cylinder-rod wiper-ring housings in reciprocating applications Dimensions and tolerances HFP Pressure relief valves Mounting surfaces Methods of test for petroleum and its products BS 2000-439: Determination of water Potentiometric Karl Fischer titration method PFP Compressed air lubricators Part 1: Main characteristics to be included in suppliers literature and product marking requirements Key TCs 1 7 TCs 5 5 5 5 5 3 3 3 3 7 16 3 4

BS ISO 6162-1:2002

BS ISO 6162-2:2002

BS ISO 6194-1:2007 BS ISO 6194-2:2009 BS ISO 6194-3:2009 BS ISO 6194-4:2009 BS ISO 6194-5:2008 BS ISO 6195:2002 BS ISO 6264:1998 BS ISO 6296:2000 BS ISO 6301-1:2009

7 7 7 7 7 7 5 16 5

10

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards - continued
Number BS ISO 6431:1992 BS ISO 6432:1985 BS ISO 6547:1981 BS ISO 6605:2002 BS ISO 6743-1:2002 BS ISO 6743-3:2003 BS ISO 6743-5:2006 BS ISO 6743-99:2002 BS ISO 6805:1994 BS ISO 6953-1:2000+ Corr 1 BS ISO 6953-2:2000 Title PFP Single rod cylinders, 1 000 kPa (10 bar) series with detachable mountings, bores from 32 to 320mm Mounting dimensions PFP Single rod cylinders 10 bar (1 000 kPa) series Bores from 8 to 25mm Mounting dimensions HFP Cylinders Piston seal housings incorporating bearing rings Dimensions and tolerances HFP Hoses and hose assemblies Test methods Lubricants, industrial oils and related products (class L) Classification Part 1: Family A (total loss systems) Lubricants, industrial oils and related products (class L) Classification Part 3: Family D (compressors) Lubricants, industrial oils and related products (class L) Classification Part 5: Family T (turbines) Lubricants, industrial oils and related products (class L) Classification Part 99: General Rubber hoses and hose assemblies for underground mining Wire reinforced hydraulic types for coal mining - Specification PFP Compressed air pressure regulators and filter regulators Part 1: Main characteristics to be included in literature from suppliers and product marking requirements PFP Compressed air pressure regulators and filter regulators Part 2: Test methods to determine the main characteristics to be included in literature from suppliers PFP Cylinders Bore and port thread sizes HFP Cylinders Bore and rod area ratios HFP Quick-action couplings Part 2: Test methods HFP Housing for elastomer energised plastic faced seals Dimensions and tolerances Part 1: Piston seal housings HFP Housing for elastomer energised plastic faced seals Dimensions and tolerances Part 2: Rod seal housings HFP Two, three and four-port screw-in cartridge valves - Cavities HFP Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 0,5 Clamping dimensions Lubricants, industrial oils and elated products (class L) Family T (turbines) Specification for lubricating oils for turbines HFP Single rod cylinders 16 MPa (160 bar) compact series Tolerances HFP Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250) bar series Mounting dimensions for accessories HFP Single rod cylinders, 16 MPa (160 bar) compact series Mounting dimensions for accessories HFP Single rod cylinders 16 MPa (160 bar) medium and 25 MPa (250 bar) series Tolerances HFP Single rod cylinders, 16 MPa (160 bar) medium series Port dimensions HFP Single rod cylinders 250 bar (25 MPa) series Port dimensions HFP Single rod cylinders 16 MPa (160 bar) compact series Port dimensions PFP Cylinders 1 000 kPa (10 bar) series Mounting dimensions of rod end spherical eyes PFP Cylinders 1 000 kPa (10 bar) series Mounting dimensions of rod end clevises Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance Key 3 3 7 4 16 16 16 16 4 5

BS ISO 7180:1986 BS ISO 7181:1991 BS ISO 7241-2:2000 BS ISO 7425-1:1998 BS ISO 7425-2:1989 BS ISO 7789:2007 BS ISO 7790:1997 BS ISO 8068:2006 BS ISO 8131:1992 BS ISO 8132:2006 BS ISO 8133:2006 BS ISO 8135:1999 BS ISO 8136:1986 BS ISO 8137:1986 BS ISO 8138:1998 BS ISO 8139:2009 BS ISO 8140:2009 BS ISO 8331:2007

3 3 4 7 7 5 5 16 3 3 3 3 3 3 3 3 3 4

11

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards - continued
Number BS ISO 8426:2008 BS ISO 8434-2:2007 BS ISO 8434-3:2005 BS ISO 8434-6:2009+ Corr:2010 BS ISO 8778:2003 BS ISO 9276-1:1998 BS ISO 9276-2:2001 Title HFP - Positive displacement pumps and motors - Determination of derived capacity Metallic tube connections for fluid power and general use Part 2: 37 flared connectors Metallic tube connections for fluid power and general use Part 3: O-ring face seal connectors Metallic tube connections for fluid power and general use Part 6: 60 cone connector with or without O-ring PFP Standard reference atmosphere Representation of results of particle size analysis Part 1: Graphical representation Representation of results of particle size analysis Part 2: Calculation of average particle sizes/diameters and moments from particle size distributions Representation of results of particle size analysis Part 4: Characterisation of a classification process Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 4: Dimensions, design, test methods and requirement for external hex and internal hex port plugs Lubricants, industrial oils and related products (class L) Family T (turbines) Specifications of triaryl phosphate ester turbine control fluids (category ISO-L-TCD) PFP Cylinders Final examination and acceptance criteria HFP Cylinders Acceptance tests HFP Four and five-port servo valves Mounting surfaces HFP Cylinder mounting dimensions 10 MPa (100 bar) series HFP Cylinders Housing dimensions for rectangular section-cut bearing rings for pistons and rods HFP Determination of pressure ripple levels generated in systems and components Part 1: Precision method for pumps HFP Determination of pressure ripple levels generated in systems and components Part 2: Simplified method for pumps HFP Determination of pressure ripple levels generated in systems and components Part 3: Method for motors HFP Electrically modulated hydraulic control valves Part 1: Test methods for four-port directional flow control valves HFP Electrically modulated hydraulic control valves Part 2: Test methods for three-way directional flow control valves HFP Electrically modulated hydraulic control valves Part 3: Test methods for pressure control valves HFP Fatigue pressure testing of metal pressure containing envelopes Part 1: Test method HFP Fatigue pressure testing of metal pressure containing envelopes Part 2: Rating methods HFP Gas-loaded accumulators Dimensions of gas ports HFP Gas-loaded accumulators with separator Selection of preferred hydraulic ports Key 8 4 4 4 5 6 6

BS ISO 9276-4:2001 BS ISO 9974-4:2006

6 4

BS ISO 10050:2005

16

BS ISO 10099:2001 BS ISO 10100:2001 BS ISO 10372:1992 BS ISO 10762:1997 BS ISO 10766:2006 BS ISO 10767-1:1996 BS ISO 10767-2:1999 BS ISO 10767-3:1999 BS ISO 10770-1:2009 BS ISO 10770-2:1998 BS ISO 10770-3:2007 BS ISO 10771-1:2002 BS ISO 10771-2:2008 BS ISO 10945:1994 BS ISO 10946:1999

3 3 5 3 7 8 8 8 8 8 8 8 8 1 1

12

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards - continued
Number BS ISO 11158:2009+ Corr:2010 BS ISO 11170:2003 BS ISO 11171:1999 BS ISO 11237-2:2006 BS ISO 11500:2008 BS ISO 11727:1999 BSI ISO 11943:1999 BS ISO 12151-1:2010 BS ISO 12151-2:2003 Title Lubricants, industrial oils and related products (class L) Family H (hydraulic systems) Specifications for HH, HL, HM, HV and HG HFP Filter elements Sequence of tests for verifying performance characteristics HFP Calibration of automatic particle counters for liquids Rubber hoses and hose assemblies Wire braid reinforced compact types for hydraulic applications Specification HFP Determination of the particulate contamination level of a liquid sample by automatic particle counting using the light-extinction principle PFP Identification of ports and control mechanisms of control valves and other components HFP On-line automatic particle counting systems for liquids Methods of calibration and validation Connections for hydraulic fluid power and general use Hose fittings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Connections for hydraulic fluid power and general use Hose fittings Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 cone connector ends with O-rings Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends Connections for hydraulic fluid power and general use Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends Connections for hydraulic fluid power and general use Hose fittings Part 5: Hose fittings with ISO 8434-2 37 flared ends Connections for hydraulic fluid power and general use Hose fittings Part 6: Hose fittings with ISO 8434-6 60 cone ends PFP Directional control valves Measurement of shifting time Filters for compressed air Test methods Part 1: Oil aerosols Filters for compressed air Test methods Part 2: Oil vapours Rubber Standard reference elastomers (SREs) for characterising the effect on vulcanised rubbers Determination of particle size distribution by gravitational liquid sedimentation methods Part 1: General principles and guidelines Determination of particle size distribution by gravitational liquid sedimentation methods Part 2: Fixed pipette method Determination of particle size distribution by gravitational liquid sedimentation methods Part 3: X-ray gravitational technique Petroleum products Determination of the filterability of lubricating oils Part 1: Procedure for oils in the presence of water Petroleum products Determination of the filterability of lubricating oils Part 2: Procedure for dry oils HFP Cylinders Method for determining the buckling load HFP Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 to 500mm Accessory mounting dimensions PFP Push-in connectors for thermoplastic tubes HFP Determination of the fluid borne noise characteristics of components and systems Part 1: Introduction HFP Determination of the fluid borne noise characteristics of components and systems Part 2: Measurement of speed of sound in a fluid in a pipe Connections for fluid power and general use Hydraulic couplings for diagnostic purposes Part 1: Coupling not for connection under pressure Connections for fluid power and general use Hydraulic couplings for diagnostic purposes Part 2: Coupling with M16 x 2 end for connection under pressure Key 16 6 6 4 6 5 6 4 4

BS ISO 12151-3:2010 BS ISO 12151-4:2007 BS ISO 12151-5:2007 BS ISO 12151-6:2009 BS ISO 12238:2001 BS ISO 12500-1:2007 BS ISO 12500-2:2007 BS ISO 13226:2005 BS ISO 13317-1:2001 BS ISO 13317-2:2001 BS ISO 13317-3:2001 BS ISO 13357-1:2002 BS ISO 13357-2:2005+ Corr 1 BS ISO 13725:2001 BS ISO 13726:2008 BS ISO 14743:2004 BS ISO 15086-1:2001 BS ISO 15086-2:2000 BS ISO 15171-1:1999 BS ISO 15171-2:2000

4 4 4 4 5 5 5 4 6 6 6 16 16 3 3 4 8 8 4 4

13

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards - continued
Number BS ISO 15217:2000 BS ISO 15218:2003 BS ISO 15380:2002 Title Fluid power systems and components 16mm square electrical connector with earth contact Characteristics and requirements PFP 3/2 solenoid valves Mounting interface surfaces Lubricants, industrial oils and related products (class L) Family H (hydraulic systems) Specifications for categories HETG, HEPG, HEES and HEPR PFP Five-port directional control valves, sizes 18 and 26mm Part 1: Mounting interface surfaces without electrical connector PFP Five-port directional control valves, sizes 18 and 26mm Part 2: Mounting interface surfaces with optional electrical connector PFP Cylinders with detachable mountings, 1000 kPa (10 bar) series, bores from 32 to 320mm Basic mounting and accessories dimensions HFP Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications PFP Connections Ports and stud ends Mobile elevating work platforms Design calculations, safety and test methods Impact of changes in ISO fluid power particle counting Contamination control and filter test standards Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 1: Nominal dimensions and tolerances Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 2: Vocabulary Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 3: Storage, handling and installation Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 4: Performance test procedures Rotary shaft lip-type seals incorporating thermoplastic sealing elements Part 5: Identification of visual imperfections HFP Single rod, short-stroke cylinders with bores from 32 to 100mm for use at 10 MPa (100 bar) Mounting dimensions HFP Filters Test method for differential pressure devices HFP Pressure switches Mounting surfaces HFP Filters Multi-pass method for evaluating filtration performance of a filter element HFP Test code for the determination of sound power levels using sound intensity techniques Engineering method Part 1: Pumps Hydraulic Tools Vocabulary PFP - Valves - Data to be included in supplier literature HFP - Hose assemblies - Part 1: Dimensions and requirements HFP Electrically controlled hydraulic pumps Test methods to determine performance characteristics HFP Cleanliness of parts and components Inspection document and principles related to contaminant collection, analysis and data reporting Rubber hoses and hose assemblies Wire or textile reinforced single pressure types for hydraulic applications - Specification HFP Methods to assess the reliability of hydraulic components Part 1: General procedures and calculation method PFP Assessment of component reliability by testing Part 1: General procedures PFP Assessment of component reliability by testing Part 2: Directional control valves PFP Assessment of component reliability by testing Part 3: Cylinders with piston rod PFP Assessment of component reliability by testing Part 4: Pressure regulators Key 5 5 16

BS ISO 15407-1:2000 BS ISO 15407-2:2003 BS ISO 15552:2004 BS ISO 16028+A1:1999 BS ISO 16030+A1:2001 BS ISO 16368:2003 BS ISO 16386:1999 BS ISO 16589-1:2001 BS ISO 16589-2:2001 BS ISO 16589-3:2001 BS ISO 16589-4:2001 BS ISO 16589-5:2001 BS ISO 16656:2004 BS ISO 16860:2005 BS ISO 16873:2002+ Corr 1 BS ISO 16889:2008 BS ISO 16902-1:2003 BS ISO 17066:2007 BS ISO 17082:2004 BS ISO 17165-1:2007 BS ISO 17559:2003 BS ISO 18413:2002 BS ISO 18752:2006 BS ISO 19972-1:2009 BS ISO 19973-1:2007 BS ISO 19973-2:2007 BS ISO 19973-3:2007 BS ISO 19973-4:2007

5 5 3 4 4 9 6 7 7 7 7 7 3 6 5 6 8 9 5 4 8 6 4 8 8 8 8 8

14

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards implemented as British standards - continued
Number BS ISO 20401:2005+ Corr 1 BS ISO 21018-1:2008 BS ISO 21018-3:2008 BS ISO 21287:2004 BS ISO 23181:2007 BS ISO 23297:2008 BS ISO 23309:2007 BS ISO 27407:2010 BS ISO 28702:2008 Title PFP Directional control valves Specification of pin assignments for electrical round connectors of diameters 8 and 12mm HFP Monitoring the level of particulate contamination of the fluid Part 1: General principles HFP Monitoring the level of particulate contamination of the fluid Part 3: Use of the filter blockage technique PFP Cylinders Compact cylinders 1 000 kPa (10 bar) series, bores from 20 to 100mm HFP Filter elements Determination of resistance to flow fatigue using high viscosity fluid Thermoplastics hoses and hose assemblies Wire or synthetic yarn reinforced single pressure types for hydraulic applications - Specification HFP Assembled systems Methods of cleaning lines by flushing HFP Marking of performance characteristics on hydraulic filters Rubber and plastics hoses and tubing Textile reinforced types Sub-ambient temperature crush test Key 5 6 6 3 6 4 6 6 4

15

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards
Number ISO 1179:1981 ISO 1219-1:2006 Title Pipe connections, threaded to ISO 228-1 for plain end steel and other metal tubes in industrial applications Fluid Power Systems and Components - Graphic symbols and circuit diagrams Part 1: Graphic symbols for conventional use and dataprocessing applications Vulcanised rubber Guide to storage Specification Acceptance tests for centrifugal, mixed flow and axial pumps Part 1: Class C tests Petroleum products Calculation of viscosity index from kinematic viscosity HFP - Positive displacement pumps and motors - Dimensions and identification code for mounting flanges and shaft ends Part 3: Polygonal flanges (including circular flanges) Rolling bearings Bearings with spherical outside surface and extended inner ring width Part 3: Specification for dimensions of cast and pressed housings Fluid Power Systems and Components - Cylinder bores and piston rod diameters - Metric series Fluid Power Systems and Components - Cylinder bores and piston rod diameters - Inch series Classification for viscosity grades of industrial liquid lubricants Specification for acceptance tests for centrifugal mixed flow and axial pumps Part 2: Class B tests Fluid Power Systems - O-rings Part 5: Suitability of elastomeric materials for industrial applications HFP - Pumps and motors, geometric displacements HFP - Fluid sample containers - Qualifying and controlling cleaning methods Glossary of terms for compressors, pneumatic tools and machines Part 1: General Glossary of terms for compressors, pneumatic tools and machines Part 3 Pneumatic tools and machines HFP - Contamination analysis - Method for reporting analysis data Fluid Power Systems and Components - Multiple lip packing sets - Methods for measuring stack heights Plastics hoses and hose assemblies - Textile reinforced types for hydraulic applications - Specification HFP - Particulate contamination analysis - Extraction of fluid samples from lines of an operating system Petroleum products Inhibited mineral oils Determination of oxidation characteristics Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test Part 2: Procedure for category HFC hydraulic fluids HFP - Pumps, motors and integrated transmissions - Parameter definitions and letter symbols HFP - Determination of characteristics of motors Part 3: At constant flow and constant torque Fluid Power Systems and Components - Cylinders - Basic series of piston strokes Fluid Power Systems and Components - Cylinder barrels Part 1: Requirements for steel tubes with specially finished bores Key 4 TCs

ISO 2230:2002 ISO 2548:1973 ISO 2909:2002 ISO 3019-3:1988

4 8 16 8

ISO 3228:1997

ISO 3320:1987 ISO 3321:1975 ISO 3448:1992 ISO 3555:1977 ISO 3601-5:2002 ISO 3662:1976 ISO 3722:1976 ISO 3857-1:1977 ISO 3857-3:1979 ISO 3938:1986 ISO 3939:1977 ISO 3949:1991 ISO 4021:1992 ISO 4263:1986 ISO 4263-2:2003

3 3 16 3 7 8 6 9 9 6 7 4 6 16 16

ISO 4391:1983 ISO 4392-3:1993 ISO 4393:1978 ISO 4394-1:1980

8 8 3 3

16

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards continued
Number ISO 4397:1993 ISO 4399:1995 ISO 4400:1994 ISO 4405:1991 ISO 4412-1:1991 ISO 4412-2:1991 ISO 4412-3:1991 ISO 5599-3:1990 ISO 5783:1995 ISO 5784-1:1988 ISO 5784-2:1989 ISO 5784-3:1989 ISO 6150:1988 Title Fluid Power Systems and Components - Connectors and associated components - Nominal outside diameters of tubes and nominal hose sizes Fluid Power Systems and Components - Connectors and associated components - Nominal pressures Fluid Power Systems and Components - Three-pin electrical plug connectors with earth contact - Characteristics and requirements HFP - Fluid contamination - Determination of particulate contamination level by the gravimetric method HFP - Test code for determination of airborne noise levels Part 1: Pumps HFP - Test code for determination of airborne noise levels Part 2: Motors HFP - Test code for determination of airborne noise levels Part 3: Pumps Method using a parallel piped microphone array PFP - Five-port directional control valves Part 3: Code system for communication of valve functions HFP - Code for identification of valve mounting surfaces and cartridge valve cavities Fluid Power Systems and Components - Fluid logic circuits Part 1: Symbols for binary logic and related functions Fluid Power Systems and Components - Fluid logic circuits Part 2: Symbols for supply and exhaust as related to logic symbols Fluid Power Systems and Components - Fluid logic circuits Part 3: Symbols for logic sequencers and related functions PFP - Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar, 25 bar (1 MPa, 1,6 MPa and 2,5 MPa) - Plug connecting dimensions, specifications, application guidelines and testing HFP - Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 and 400 bar) Petroleum products - Determination of foaming characteristics of lubricating oils HFP - Compensated flow-control valves - Mounting surfaces PFP - Compressed air lubricators Part 2: Test methods to determine the main characteristics to be included in suppliers' literature PFP - Components using compressible fluids - Determination of flow-rate characteristics HFP - Valves controlling flow and pressure - Test methods HFP Servo-valves Test Methods PFP - Single rod cylinders, 1000 kPa (10 bar) series, with integral mountings, bores from 32 mm to 250 mm - Mounting dimensions PFP Cylinder barrels Requirements for non-ferrous metallic tubes Lubricants, industrial oils and related products (class L) Classification Part 0: General Lubricants, industrial oils and related products (class L) Part 2: Classification for family F (spindle bearings, bearing and associated
clutches

Key 4 4 5 6 8 8 8 5 5 5 5 5 4

ISO 6164:1994 ISO 6247:1998 ISO 6263:1997 ISO 6301-2:2006 ISO 6358:1989 ISO 6403:1988 ISO 6404:1985 ISO 6430:1992 ISO 6537:1982 ISO 6743-0:1981 ISO 6743-2:1981 ISO 6801:1983 ISO 6952:1994 ISO 7233:1991 ISO 7241-1:1987 ISO 7368:1989 ISO 7662:1988

4 16 5 5 5 5 5 3 3 16 16 4 5 4 4 5 4

Rubber and plastics hoses Determination of volumetric expansion Fluid Power Systems - Two-pin electrical plug connectors with earth contact - Characteristics and requirements Rubber and plastics hoses and hose assemblies Determination of suction resistance HFP - Quick-action couplings Part 1: Dimensions and requirements HFP Two-port slip in cartridge valves - Cavities Rubber and plastics hoses Determination of abrasion of lining

17

FP010007 25 October 2010

INTERNATIONAL STANDARDS ORGANISATION

International standards continued
Number ISO 7745:1989 ISO 7986:1997 ISO 9110-1:1990 ISO 9110-2:1990 ISO 9461:1992 ISO 9632:1992 ISO 10763:1994 ISO 10949:2002 ISO 11340:1994 ISO 11926-1:1995 Title HFP - Fire-resistant (FR) fluids -Guidelines for use HFP - Sealing devices - Standard test methods to assess the performance of seals used in oil hydraulic reciprocating applications HFP - Measurement techniques Part 1: General measurement principles HFP - Measurement techniques Part 2: Measurement of average steadystate pressure in a closed conduit HFP - Identification of valve ports, sub-plates, control devices and solenoids HFP Fixed displacement pumps Flow degradation due to classified AC fine test dust contamination Test method HFP - Plain-end, seamless and welded precision steel tubes - Dimensions and nominal working pressures HFP - Component cleanliness - Guidelines for achieving and controlling cleanliness of components from manufacture to installation Rubber and rubber products Hydraulic hose assemblies External leakage classification for hydraulic systems Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing Part 3: Light-duty (L series) stud ends Rubber and hoses and hose assemblies - wire braid - reinforced compact types for hydraulic applications - Specifications - Oil and water based fluid applications Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids Part 1: Spray flame persistence Hollow-cone nozzle method HFP - Determination of fluid borne noise characteristics of components and systems Part 3: Measurement hydraulic impedance Aerospace fluid systems - O-rings, inch series - Inside diameters and crosssections, tolerances and size-identification codes Part 1: Close tolerances for hydraulic systems HFP - Calibration of liquid automatic particle counters - Procedures used to certify the standard reference material SRM 2806 HFP - Assembled systems - Verification of cleanliness PFP - Cylinders - Load capacity of pneumatic slides and their presentation method HFP Hose assemblies Part 2: Recommended practices for hydraulic hose assemblies Petroleum and related products - Determination of the extreme pressure and anti-wear properties of fluids Four ball method (European conditions) Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test Petroleum and related products - Determination of pH of fire-resistant fluids within classes HFA and HFC Key 16 7 8 8 5 8 4 6 4 4

ISO 11926-2:1995 ISO 11926-3:1995 ISO 11237:2010

4 4 4

ISO 15029-1:1999

16

ISO 15086-3:2008 ISO 16031-1:2002

8 7

ISO 16144:2002 ISO 16431:2002 ISO 16806:2003 ISO 17165-2:2006 ISO 20623:2003 ISO 20823:2003 ISO 20843:2003

6 6 3 4 16 16 16

18

FP010007 25 October 2010