Modeling and Simulation of Solar Photovoltaic Module Using Matlab - Simulink

JAY PATEL* et al Volume: 2 Issue: 3
ISSN: 2319 - 1163 225 - 228
MODELING AND SIMULATION OF SOLAR PHOTOVOLTAIC MODULE USING MATLAB / SIMULINK

1
1
Jay Patel, 2Gaurag Sharma
PG Student, 2Assistant professor Electrical department, Birla Vishvakarma Mahavidhyalaya, Gujarat, India, jaypatel151188@gmail.com, gksharma@bvmengineering.ac.in
Abstract
The paper presents the modeling ,simulation and implementation of the solar photovoltaic cell using MATLAB/SIMULINK .The I-V , P-V & I-V characteristics are obtained for (1) Single solar cell module (2) Solar PV module with variable temp.& fixed radiation (3) Solar PV module with fixed temp.& variable radiation with M.file and mathematical model using MATLAB/SIMULINK .
Index Terms: photovoltaic module, radiation, temperature ,M.file, MATLAB/SIMULINK -----------------------------------------------------------------------***----------------------------------------------------------------------1. INTRODUCTION
One of the major concerns in the power sector is the day-today increasing power demand but the unavailability of enough resources to meet the power demand using the conventional energy sources. Energy is the prime mover of economic growth and is vital to the sustenance of a modern economy .Future economic growth crucially depends on the long-term availability of energy from sources that are affordable , accessible and environment. Demand has increased for renewable sources of energy to be utilized along with conventional systems to meet the energy demand. Renewable sources like wind energy and solar energy are the prime energy sources which are being utilized in this regard. The continuous use of fossil fuels has caused the fossil fuel deposit to be reduced and has drastically affected the environment depleting the biosphere and cumulatively adding to global warming. Solar energy is abundantly available that has made it possible to harvest it and utilize it properly. Solar energy can be a standalone generating unit or can be a grid connected generating unit depending on the availability of a grid nearby. Thus it can be used to power rural areas where the availability of grids is very low. Another advantage of using solar energy is the portable operation whenever wherever necessary. In order to tackle the present energy crisis one has to develop an efficient manner in which power has to be extracted from the incoming solar radiation. The power conversion mechanisms have been greatly reduced in size in the past few years. The development in power electronics and material science has helped engineers to come up very small but powerful systems to withstand the high power demand. they can hardly compete in the competitive markets as a prime power generation source. The PV module represents the fundamental power conversion unit of PV generator system. The output characteristics of PV module depends on the solar radiation ,the cell temperature and output voltage of PV module.
2. PV MODULE
A solar cell is the building block of a solar panel. A photovoltaic module is formed by connecting many solar cells in series and parallel. Considering only a single solar cell; it can be modeled by utilizing a current source, a diode and two resistors. This model is known as a single diode model of solar cell. Two diode models are also available but only single diode model is considered here in fig. 1
Fig. 1 Equivalent circuit model of PV cell The characteristic equation for a photovoltaic cell is given by Io =(Np * Iph)- (Np* Irs) * (exp((q/(k*T*A))*(Vo/ Ns))-1) (1) Where Iph=(Iscr+ki*(T-Tr))* ((s)/100); (2) (3)
Irs= Irr * ((T/Tr)^3) * exp(q*Eg/(k*A) * ((1/Tr)-(1/T)) Tr=(Tr1-32)+273 (4)
Io& Vo : Cell output current and voltage; Irs : Cell reverse saturation current; T : Cell temperature in Celsius; k : Boltzmann's constant :1.38 * 10-19 J/K;
__________________________________________________________________________________________ IJRET | MAR 2013, Available @ http://www.ijret.org/ 225

q : Electron charge: 1.6*10-23 C; Ki : Short circuit current temperature coefficient at Iscr; S : Solar radiation ; Iscr : Short circuit current at 25 degree Celsius; Iph : Light-generated current; Eg : Band gap for silicon; Tr : Reference temperature; Rsh : Shunt resistance; Rs : Series resistance; A PV array is a group of several PV cells which are electrically connected in series and parallel circuits to generate the required current and voltage. The equivalent circuit for the solar module arrange in Np parallel and Ns series cells is shown in fig. 2
1 Out1
Ppv
ISSN: 2319 - 1163 225 - 228

1 In1
Ipv Ppv
2 In2 Product
PV To Workspace
3 In3
1e-9*(exp(u/26e-3)-1) PN-junction characteristic
Id Id
2 Out2
4 In4
1/1000 Insolation to ISC current gain
ISC
Ipv
Fig. 4 Subsystem of single photovoltaic cell model
Fig.2 Equivalent circuit of solar array The shunt resistance Rsh is inversely related with shunt leakage current to the ground .In general , the PV efficiency is insensitive to variation in Rsh and the shunt -leakage resistance can be assumed to approach infinity without leakage current to ground . on the other hand ,a small variation in Rs will significantly affect the PV output power .
3. IMPLEMENTATION AND SIMULATION OF MODEL

1) The proposed model of single solar photovoltaic cell is implemented and shown in fig. 3 and fig. 4
Vpv
Fig.5 I-V characteristics of single solar cell
SOLAR _ PV _ Singal Cell
In1 Out1 Vpv Vpv In2
PV power
Vpv
In3 Out2
1000
In4
I-V characteristic Solar Cell
Insolation
Fig. 3 Masked single photovoltaic cell model
Fig.6 P-V characteristics of single solar cell

4000 3500 3000 2500 2000 1500 1000 500 0
ISSN: 2319 - 1163 225 - 228
power in watt
20
40
60 80 current in amp
100
120
Fig. 10 P-I characteristics of solar cell with variable Temp. & Fixed Radiation 3) Output of Solar PV Array with Fixed Temp. & variable Radiation using M.file and matlab modeling
20 18 16 14
120
Fig. 7 MATLAB simulation of PV module 2) Output of Solar PV Array with variable Temp. & Fixed Radiation using M.file and matlab modeling
Current in amp
12 10 8 6
100
Current in amp
80
60
4 2
40
10
15
20 25 30 Voltage in volt
35
40
45
50
20
10
15
20 25 Voltage in volt
30
35
40
45
Fig. 11 I-V characteristics of solar cell with Fixed Temp. & variable Radiation
400 350
Fig. 8 I-V characteristics of solar cell with variable Temp. & Fixed Radiation
4000 3500 3000 2500 2000 1500 1000 500
300 250 200 150 100 50 0
power in watt
power in watt
10
15
10
15
20 25 Voltage in volt
30
35
40
45
20 25 30 Voltage in volt
35
40
45
50
Fig. 9 P-V characteristics of solar cell with variable Temp. & Fixed Radiation
Fig. 12 P-V characteristics of solar cell with Fixed Temp. & variable Radiation

400 350 300 250 200 150 100 50 0
ISSN: 2319 - 1163 225 - 228

[6] I. S. Kim and M. J. Youn, Variable-structure observer for solar array current estimation in a photovoltaic powergeneration system, IEE Proceedings-Electric Power Applications, , vol. 152, no. 4, 2005, pp. 953959.
power in watt
BIOGRAPHIES:
Jay Patel received the B.E(Electrical Engineering) degree from Sardar Patel University (Birla Vishvakarma Mahavidhyalaya Engineering College) in 2010. he is currently a M.E (power system) student (3rd semester) In Birla Vishvakarma Mahavidhyalaya Engineering College from Gujarat Technological University. His current research interests include solar enregy and power system protection Prof Gaurang K.Sharma is Presently working in Electrical Engineering Dept .B.V.M Engineering College .previously worked with ERDA Baroda having total 12 years experience in Multinational Industries as well as Academic Institutions.
8 10 12 current in amp
14
16
18
20
Fig. 13 P-I characteristics of solar cell with Fixed Temp. & variable Radiation
CONCLUSION
The proposed model and using m.file of PV module takes solar radiation intensity and cell temperature as input and outputs the I-V and P-V characteristics under various conditions. we conclude that The insolation change affects the photon generated current and has very little effect on the open circuit voltage and we also simulate and modeling of solar cell and measure the different characteristics. and also measure the effect of variation in temperature that if the temperature increases the solar cell efficiency is reduced. As we increase the solar radiation, higher would be the solar input to the solar cell and hence power magnitude would increase for the same voltage value. With increase in the solar radiation the open circuit voltage increases. This model can be used for the analysis in the field of solar photovoltaic system and MPPT technologies .
ACKNOWLEDGEMENTS
The authors would like to thank Dr.. B.R Parekh and prof. N.G misra of Birla Vishavakarma Mahavidhyalaya Engineering College,v.v nagar ,Gujarat,India contribution to this paper.
REFERENCES:
[1] John A. Duffie & William A. Beckman, Solar Engineering of Thermal Process, 3rd ed,John Wiley & Sons, pp. 747-773, (2006). [2] Nicola M. Pearsall and Robert Hill, Clean electricity from photovoltaic, 3rd ed., World Scientific, pp. 671 -712, (2004) [3] R. Messenger and J. Ventre, Photovoltaic Systems Engineering, CRC Press, 2000, pp.41-51. [4] S. W. Angrist, , Direct Energy Conversion, Allyn and Bacon, Inc., 4th edition, 1982, pp. 177-227. [5] O. Wasynczuk, Dynamic behavior of a class of photovoltaic power systems, IEEE Transactions on Power Apparatus and Systems, vol. PAS-102, no. 9, 1983, pp. 30313037.

Modeling and Simulation of Solar Photovoltaic Module Using Matlab - Simulink

Uploaded by

Modeling and Simulation of Solar Photovoltaic Module Using Matlab - Simulink

Uploaded by

JAY PATEL* et al Volume: 2 Issue: 3

ISSN: 2319 - 1163 225 - 228