Scribd
Upload
495 views2 pages

Opcom Diesel Pump Programming

This document provides instructions for programming the diesel pump from a donor vehicle into a recipient vehicle. It describes removing the pump from the donor car and installing it in the recipient, then using a communication device to reset the engine control module and immobilizer module to the new vehicle. Specific steps are outlined for Astra G/Zafira A vehicles using a VP44/PSG5 pump and for Vectra C/Signum vehicles using a PSG16 pump. Additional modules may need to be reset depending on fault codes.

Uploaded by

Oprea Vasile
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
495 views2 pages

Opcom Diesel Pump Programming

This document provides instructions for programming the diesel pump from a donor vehicle into a recipient vehicle. It describes removing the pump from the donor car and installing it in the recipient, then using a communication device to reset the engine control module and immobilizer module to the new vehicle. Specific steps are outlined for Astra G/Zafira A vehicles using a VP44/PSG5 pump and for Vectra C/Signum vehicles using a PSG16 pump. Additional modules may need to be reset depending on fault codes.

Uploaded by

Oprea Vasile
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 2

http://www.digital-kaos.co.

uk

yary1

Diesel Pump Programming

Astra-G / Zafira-A

Donor-car

Remove dieselpump from donor-car Attention: You will need donor-car's Security Code!

Car where donor-pump needs to be installed



Install dieselpump in the car Set up communication with ECM Select [Programming] Select [Reset ECU] Enter donor-car's Security Code

This will reset the previously learnt security code. Then, your engine ECU (which is inside the pump) will be resetted, so you can learn it to the new car.

Set up communication with Immobilizer module Select [Programming] Enter Security Code of car where you have installed the dieselpump Select [Immobilizer Function Programming] Select [ECM (Motor Module) replaced]

This will learns the new Security Code to the engine control module. Astra-G and Zafira-A can also be installed with a VP44/PSG5 for Y20DTH. These PSG5 units don't need to be reset.

Vectra-C / Signum PSG16

Donor-car

Remove the diesel pump from donor-car Attention: You will need donor-car's Security Code!

Car where donor-pump needs to be installed



Install diesel pump in the car Set up communication with ECM Select [Programming]

Select [Reset ECU] Enter donor-car's Security Code

This will reset the previously learnt security code. Then, your engine ECU (which is inside the pump) will need to be reset, so you can learn it to the new car.

Set up communication with CIM module Select [Programming] Enter Security Code of car where you have installed the diesel pump Select [Immobilizer Function Programming] Select [ECM (Motor Module) replaced]

This will learns the new Security Code to the engine control module.

Reset immobilizer related controllers


Then, you need to go into each module, for which you have a corresponding fault code stored in the CIM module (see below), and do a reset/programming cycle with the security code of the car.

IPC Instrument B3925 -00 Wrong Environment Identifier Received IPC REC Rear Electrical Centre B3929 -00 Wrong Environment Identifier Received REC BCM Body Control Module B3924 -00 Wrong Environment Identifier Received BCM DDM Driver Door Module B3926 -00 Wrong Environment Identifier Received DDM PDM Passenger Door Module B3927 -00 Wrong Environment Identifier Received PDM

After the reset, you need to wait at least 10 seconds with the ignition OFF, to allow the car to learn the new identifier. Now select ECM and check programming of:

Highspeed CAN bus Variant configuration Tyresize

You might also like