Scribd
Upload
4K views3 pages

Pile Capacity Calculation

This document summarizes the calculation of safe axial compressive pile capacity for a bored cast in situ reinforced concrete pile using static analysis. The calculation is based on 9 soil layers from 0 to 40 meters depth, with properties including cohesion, effective density, earth pressure coefficient and bearing capacity factors provided. The safe pile capacity is calculated using a formula that sums the contributions from skin friction along the pile shaft and end bearing pressure at the base. Capacities are computed for pile lengths of 29 and 34.5 meters, with ultimate values of 2803.1 and 3005.1 tonnes reported.

Uploaded by

Arnab Sur
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
4K views3 pages

Pile Capacity Calculation

This document summarizes the calculation of safe axial compressive pile capacity for a bored cast in situ reinforced concrete pile using static analysis. The calculation is based on 9 soil layers from 0 to 40 meters depth, with properties including cohesion, effective density, earth pressure coefficient and bearing capacity factors provided. The safe pile capacity is calculated using a formula that sums the contributions from skin friction along the pile shaft and end bearing pressure at the base. Capacities are computed for pile lengths of 29 and 34.5 meters, with ultimate values of 2803.1 and 3005.1 tonnes reported.

Uploaded by

Arnab Sur
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 3

Project :

COMPUTATION OF SAFE AXIAL COMPRESSIVE PILE CAPACITY BY STATIC ANALYSIS Analysis in accordance with IS 2911 Part 1 Section 2-1979 Reaffirmed 1997 DMRC CC-30 : Estimation of Pile Capacity for Elevated Corridor of Existing Metro Line for using in settlement analysis

Pile Type :

Bored Cast in Situ RCC Pile

Loading :

Axial Compression

The safe pile capacity is computed as :

Qsafe=(1/FS){1 to n[(c+pktan)AsL]+[(cNc+pNq+0.5D N)Ap]}


where : Qsafe = = =
safe axial pile capacity, Tonnes adhesion factor friction angle between soil and pile, degrees ( = ) cohesion intercept, T/m2 effective density of soil, T/m3 Bearing capacity factors, which are a function of number of layers

FS p L k D As

= = = = = =

Factor of safety overburden pressure, T/m2 Pile segment length in selected layer earth pressure coefficient Pile diameter Pile surface area per m length

c = = Nc , Nq , N =

Ap = = Pile end bearing area n Pile Cross section : Circle Pile cut-off Level (COL) : 2.75 Pile Diameter ,D : 1500 mm 2 4.712 m /m length 1.767 Pile Surface Area, As = Pile cross-section Area, Ap = Overburden Pressure to be considered below : 2.75 m 20 pile diameters, i.e. 30.0 m below 2.8 Consider overburden pressure to i.e. 32.8 m below 0.0 become constant below : 2.75 m Design Water Table Depth: Factor of Safety : as per IS 1904-1986 3.0
(=), degrees
2

m
m2 m m

Layer No.

c, T/m

Depth,m From 0.0 2.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 To 2.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0

Soil Classification
Fill / Made Ground Alluvial Silt Alluvial Silt Alluvial Silt Alluvial Silt Alluvial Silt Alluvial Silt Alluvial Silt Alluvial Silt

, T/m3

k 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0

0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5

Nc

Nq

1 2 3 4 5 6 7 8 9

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0

30 30 30 30 30 30 30 30 30

2.00 2.10 2.10 2.10 2.10 2.10 2.10 2.10 2.10

20.95 20.95 20.95 20.95 20.95

22.40 22.40 22.40 22.40 22.40

Pile Capacity Calculation at following Pile Length(s) below cut-off Level (m)

29.0

34.5

Project :

COMPUTATION OF SAFE AXIAL COMPRESSIVE PILE CAPACITY BY STATIC ANALYSIS Analysis in accordance with IS 2911 Part 1 Section 2-1979 Reaffirmed 1997 DMRC CC-30 : Estimation of Pile Capacity for Elevated Corridor of Existing Metro Line for using in settlement analysis

Pile Type : Pile Dia =


Pile Length below COL, m Depth Below GL , m

Bored Cast in Situ RCC Pile 1500 mm


Skin Friction in Layer Overburden Pressure Unit Skin Friction Soil Parameters
(=), degrees

Loading :
Cumulative Skin Friction Unit End Bearing

Axial Compression Safe Pile Capacity 824 867 934


Total End Bearing

c, 2 T/m

eff,

T/m

Layer No.

T/m 2

T/m 2 Tonnes Tonnes

T/m 2

Tonnes Tonnes Tonnes

0.0 2.0 2.8 5.0 10.0 15.0 20.0 25.0 30.0 31.8 32.8

1 2 0.0 2 2.3 3 7.3 4 12.3 5 17.3 6 22.3 7 27.3 8 29.0 8 30.0 8 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 1.10 0.0 30 0.00
1.24

0.0

0.71 3.02 6.19 9.37

7.6 7.6 71.1 78.7 145.9 224.6 220.7 445.3 740.8 1111.2 1258.5 686.8 1213.6 2472.0 88.3 1346.7 709.8 1254.3 2601.1

2.48
5.23

7.98
10.73

13.48
16.23

18.98
21.73 12.54 295.5

24.48
27.23 15.72 370.4

29.98
30.94 17.86 147.3

31.90
32.45 18.74

33.00
33.00 19.05 202.0

35.0

32.3

33.00

1548.8 709.8 1254.3 2803.1

Ult. Pile Capacity

Project :

COMPUTATION OF SAFE AXIAL COMPRESSIVE PILE CAPACITY BY STATIC ANALYSIS Analysis in accordance with IS 2911 Part 1 Section 2-1979 Reaffirmed 1997 DMRC CC-30 : Estimation of Pile Capacity for Elevated Corridor of Existing Metro Line for using in settlement analysis

Pile Type : Pile Dia =


Pile Length below COL, m Depth Below GL , m

Bored Cast in Situ RCC Pile 1500 mm


Overburde n Pressure Unit Skin Friction Soil Parameters

Loading :
Skin Friction in Layer Cumulative Skin Friction Unit End Bearing

Axial Compression Safe Pile Capacity 934 1002


Total End Bearing

c, T/m

(=), degrees

eff,

T/m

Layer No.

T/m 2

T/m 2 Tonnes Tonnes

T/m 2

Tonnes Tonnes Tonnes

35.0 37.3

32.3 9 34.5 0.0 30 1.10

33.00
33.00 19.05 202.0

1548.8 709.8 1254.3 2803.1 1750.8 709.8 1254.3 3005.1

33.00

Ult. Pile Capacity

You might also like