Scribd
Upload
738 views5 pages

Renesas Flash Programmer Sample Circuit For Programming PC Serial PDF

Renesas Flash Programmer Sample Circuit for Programming PC serial.pdf

Uploaded by

Ajay J Verma
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
738 views5 pages

Renesas Flash Programmer Sample Circuit For Programming PC Serial PDF

Renesas Flash Programmer Sample Circuit for Programming PC serial.pdf

Uploaded by

Ajay J Verma
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 5

Customer Notification

Renesas Flash Programmer


Sample Circuit for Programming by Using a PCs Serial Port

MCU Tool Product Marketing Department, MCU Software Division, MCU Business Unit Renesas Electronics Corporation
2012/10/24 Rev. 3.00

2012 Renesas Electronics Corporation. All rights reserved.

R20UT0857EJ0300

Sample Type A Circuit

R20UT0857EJ0300

This document describes sample circuits for programming the flash memory of a microcontroller by using Renesas Flash Programmer connected to a PC serial port. A sample circuit for each type is shown below. A list of the microcontroller models and types that can be used with Renesas Flash Programmer is available from "Renesas Flash Programmer target devices list on the following website: http://www.renesas.com/rfp
Note: An operation check has been conducted for the sample circuit. However, there might be timing differences due to the characteristics of the target system and PC. The user is responsible for evaluating the circuit and determining whether the circuit can be applied to the user system. Renesas is not responsible concerning the applicability of the circuit.

Sample Type A Circuit (2-wire UART)


Leave unused pins open. PC with serial ports RS-232C cable (straight type) 2. RxD 3. TxD 7. RTS 9-pin D-SUB COM signal connector conversion IC (female) Inverter
Note Note

TxD FLMD0 RxD

Short these pins before power up

Note

_RESET Microcontroller See the microcontroller's manual for the names of the pins used for programming and how to handle them

Reset circuit Short these pins before power up

Target system

Assumed to be MAX232A or MAX3232 Specify the same operating voltage as the microcontroller pins TxD, RxD and _RESET See the data sheet from the IC manufacturer for the way of setting

Note Resistance is assumed to 4.7k. About Pull-up and pull-down resistor values, please check the electrical characteristics of each microcontroller, and use the appropriate resistor values.

2012 Renesas Electronics Corporation. All rights reserved.

Sample Type B Circuit

R20UT0857EJ0300

This document describes sample circuits for programming the flash memory of a microcontroller by using Renesas Flash Programmer connected to a PC serial port. A sample circuit for each type is shown below. A list of the microcontroller models and types that can be used with Renesas Flash Programmer is available from "Renesas Flash Programmer target devices list on the following website: http://www.renesas.com/rfp
Note: An operation check has been conducted for the sample circuit. However, there might be timing differences due to the characteristics of the target system and PC. The user is responsible for evaluating the circuit and determining whether the circuit can be applied to the user system. Renesas is not responsible concerning the applicability of the circuit.

Sample Type B Circuit (1-wire UART)


Leave unused pins open. PC with serial ports RS-232C cable (straight type) 2. RxD 3. TxD 7. RTS Three state buffer _RESET Inverter Microcontroller
Note Note

RL78 do not have FLMD0. Short these pins before power up FLMD0

TOOL0

9-pin D-SUB COM signal connector conversion IC (female)

Reset circuit Short these pins before power up

See the microcontroller's manual for the names of the pins used for programming and how to handle them

Target system

Assumed to be MAX232A or MAX3232 Specify the same operating voltage as the microcontroller pins TxD, RxD and _RESET See the data sheet from the IC manufacturer for the way of setting

Note Resistance is assumed to 4.7k. About Pull-up and pull-down resistor values, please check the electrical characteristics of each microcontroller, and use the appropriate resistor values.

3
2012 Renesas Electronics Corporation. All rights reserved.

Sample Type C Circuit

R20UT0857EJ0300

This document describes sample circuits for programming the flash memory of a microcontroller by using Renesas Flash Programmer connected to a PC serial port. A sample circuit for each type is shown below. A list of the microcontroller models and types that can be used with Renesas Flash Programmer is available from "Renesas Flash Programmer target devices list on the following website: http://www.renesas.com/rfp
Note: An operation check has been conducted for the sample circuit. However, there might be timing differences due to the characteristics of the target system and PC. The user is responsible for evaluating the circuit and determining whether the circuit can be applied to the user system. Renesas is not responsible concerning the applicability of the circuit.

Sample Type C Circuit (2-wire UART)


Leave unused pins open. PC with serial ports RS-232C cable (straight type) 9-pin D-SUB COM signal connector conversion IC (female) 2. RxD 3. TxD
Note1 Note1 Note2 Note1

MD0 TxD RxD


Note2 Note1 Note2 Note1

MD1

_RESET Microcontroller Reset circuit See the microcontroller's manual for the names of the pins used for programming and how to handle them

Target system

Assumed to be MAX232A or MAX3232 Specify the same operating voltage as the microcontroller pins TxD, RxD and _RESET See the data sheet from the IC manufacturer for the way of setting

Note1 Resistance is assumed to 4.7k. About Pull-up and pull-down resistor values, please check the electrical characteristics of each microcontroller, and use the appropriate resistor values. Note2 Please set each microcontroller will be entry to the boot mode before power up the target system. *This circuit example, assume RX62T Group

2012 Renesas Electronics Corporation. All rights reserved.

Renesas Electronics Corporation


2012 Renesas Electronics Corporation. All rights reserved.

R20UT0857EJ0300

You might also like