ENVE 301 Environmental Engineering Unit Operations

Chapter: 6 Mixing

Assist. Prof. Bilge Alpaslan Kocamemi

Mixing
Common Applications:

Mixing of coagulant chemicals (COAGULATION) Flocculation Addition of chlorine for disinfection Biological treatment

3 phenomena contribute to mixing: 1. Molecular diffusion is due to thermally induced Brownian motion and is not significant compared to other 2 phenomena.

2. Eddy current (generated as a result of velocity gradient) 3. Non-uniform flow The degree of mixing

are functions of the degree of turbulence in the basin.

Magnitude of eddy currents or

Velocity Gradient (G)

G
P G=
1/sec

Therefore; G must be sufficient to furnish the desired rate of particulate collisions. G shear force

P = Power dissipated , W (Nm/sec) = Dynamic viscosity, (Nsec/m 2 ) V = Volume to which the power is applied, (m 3 )

Example: Two water particles moving 1m/sec relative to each other at a distance 0,1m would have

1m / sec G= = 10 sec 1 0 .1m

Velocity gradient

measure of the relative velocity of two particles of fluid and distance between.

MIXERS

Hydraulic Mixing Devices

Mechanical Mixing Devices

Pneumatic Mixers
Air diffusers

Turbine mixer Parshall flume Weirs Baffled mixing chambers Paddle mixer

Hydraulic Mixers

The degree of turbulence is measured by the loss in head. Dependent on flow Power dissipation in a hydraulic device= gQ h L
Headloss

Hydraulic Mixers (continue)

V1

V2

Venturi section for chemical addition

V2 2 hL = C d 2g

A) Venturi Sections

The reduced pressure in the throat of the section aspirates the chemical feed solution into flow. Turbulence generated in the throat. As the flow jet expands upon exiting the throat Mixing.
8

B) Hydraulic Jumps

Ref: Schulz & Okun, 1984, John Wiley & Sons

A chute followed by a channel, with or without a drop in the elevation of channel floor. Creates supercritical flow. Provide suitable mixing.
9

Chute

Turbulence generated in the jump

C) Parshall Flume

Ref: Schulz & Okun, 1984, John Wiley & Sons

Effective rapid mixer when a hydraulic jump is incorparated immediately downstream of flume.

10

D) Weirs

The sudden drop in the hydraulic level over the weir induces the turbulence in water for mixing. Chemicals are added over weir with the help of diffusers. The vertical fall of water the weir The height of the coagulant diffuser over the weir at least 0.1m to ensure sufficient turbulence at least 0.3m to penetrate the nappe thickness
11

12

13

14

E) Baffled Mixing Chambers

15

HorizontalHorizontal -flow baffled channel flocculator

Vertical Vertical-flow baffled channel flocculator

Ref: Schulz & Okun, 1984, John Wiley & Sons

Mixing is accomplished by reversing the flow of water through channels formed. a) Around-the-end (horizontal flow) baffles b) Over-and-under (vertical flow) baffles

F) Static Mixers
contain internal vanes or orifice plates that bring about sudden changes in the velocity pattern are identified by their lack of moving parts mixing occurs in a plug-flow regime the longer the mixing element the better the mixing however headloss increases Mixing time is quite short typically less than 1 sec. In-line Mixers

Angled vanes promote turbulance

similar to static mixers but contain a rotating mixing element to enhance the mixing.

16

Mechanical Mixing Devices Turbine and Propeller Mixers

D = diameter of impeller , m n = rev/sec = density of liquid , kg/m 3 = dynamic viscosity Ns/m 2 R = reynolds number (unitless )

Reynolds number : Re <10 Re>1000

laminar turbulent

Vortexing :

Liquid to be mixed rotates with the impeller Reduction in the difference between the fluid velocity and the impeller
velocity ( effectiveness of mixing decreases) In circular or rectangular tanks the usual method used to limit vortexing. To install 4 or more vertical baffles extending approximately 1/10th the diameter out from the wall.
1 10 or 1 12 D
1 10 or 1 12 WL

18

Power imparted in an unbaffled tank = 1/6 of the power imparted in the same tank with baffles

Power imparted in an unbaffled square tank

75% of the power imparted in a baffled square or a baffled circular tank.

Power in a baffled vertical square tank Power in a baffled vertical circular tank having D=width of square tank

19

In small tanks (to prevent vortexing):

Mounting the impeller off-center Mounting the impeller at angle with verticle Mounting the impeller to the side of basins at angle
Turbine or propeller mixers are usually constructed with a vertical shaft driven by a speed reducer and electric motor. Types of Impellers : 1. Radial flow impellers Generally have flat or curved blades located parallel to the axis of shaft. 2. Axial flow impellers Make an angle of less than 90o with drive shaft.
20

Turbine and Propeller Mixers (continue)

Laminar flow
for Re<10
Developed by Rushton

P = kn
Power (watt) Impeller constant

Revolutions per second rev/sec

Diameter of impeller (m)

Power imparted in either baffled or unbaffled tank

Dynamic viscosity

21

Turbine and Propeller Mixers (continue)

Turbulent flow
(for Re>10000)

P = k n
Impeller constant

Power (watt)
Nm sec

Revolutions per second rev/sec

Diameter of impeller (m)

Power imparted in a baffled tank

Density
kg m 3

22

Turbine and Propeller Mixers (continue)

23

Power imparted in an unbaffled tank (valid for laminar and turbulent flow)
Ref: Tchobanoglous and Scroeder, 1985, Addison-Wesley Publishing Company

= Power function dimensionless =

P N3D 5

k= constant of an impeller P= -1 (for laminar) P= 0 (for turbulent)

tank geometry
24

25
Ref: Reynolds/Richards 2nd Edition

Types of Propeller Impellers

Ref: Reynolds/Richards 2nd Edition

Ref: Reynolds/Richards 2nd Edition

26

Propeller Mixer

Ref: Metcalf Eddy,1991, McGraw Hill

27

Propeller Mixer

28
Ref: http://screw-jack.en.made-in-china.com/product/kqNmSdnCrHWR/China-Propeller-Shaft-Mixers.html

Types of Turbine Impellers

Ref: Reynolds/Richards 2nd Edition

29

Types of Turbine Impellers

Ref: Metcalf Eddy,1991 , McGraw Hill

Ref: Metcalf Eddy,1991 , McGraw Hill

30

Types of Turbine Impellers

31

Turbine Mixer in a Baffled Tank

(Ref: Tchobanoglous and Scroeder, 1985, Addison-Wesley Publishing Company)

32

Ref: Reynolds/Richards 2nd Edition

33

Example: Determine the power requirements for 3 m diameter, six-blade flatblade turbine impeller mixer running at 15 rpm in a 10 m diameter mixing tank. Assume the fluid being mixed is water. ( T = 15 0 C , = 1 .139 Ns / m2 , = 999 .1 kg / m )3

34

Padddle Mixers

consists of a series of appropriately spaced paddles mounted on either a horizontal or vertical shaft generally rotate slowly

are commonly used as flocculation devices

35
Ref: Reynolds/Richards 2nd Edition

36

37

38

Paddle Impellers

Ref: Reynolds/Richards 2nd Edition

Ref: Reynolds/Richards 2nd Edition

39

Paddle Impellers

Ref: Reynolds/Richards 2nd Edition Ref: Reynolds/Richards 2nd Edition

40

POWER IMPARTED TO THE WATER BY PADDLE

Newtons Law for the drag force exerted by a submerged object moving in a liquid.

FD =

C D A Vp 2 2

FD = Drag force (1bf or N ) C D = Drag coefficien t

Vp=Relative velocity of paddles with respect to water.

0.6 - 0.75 Vpaddle tip Vpaddle tip= 2-3 ft/sec (0.6-0.9m/sec )

r
Shaft (N,rpm)

Velocity of paddle (paddle tip velocity)

2N r 60
1min/60sec

m/sec

Distance from shaft to paddle center(m)

P = FD V

AVP 2

Power

Force

Velocity

A=Cross-sectional area of paddle (ft2 or m2 ) (paddle-blade area at night angle to the direction of movement) slug kg = Density of fluid ( 3 or 3 ) ft m Vp=Relative velocity of paddles with respect to water. Cd=Drag coeff.
42

THE DRAG COEFFICIENT (Cd)

depends basically on the geometry of the paddle CD 1.20 1.5 1.90

L/W ratio 5 20

43

Example: Determine the theoretical power requirement and the paddle area required to achieve a G value of 50 sec-1 in a tank with a volume of 2832 m3.

(Water temperature =

15 0 C = 999 .5

kg = 1.139.10 3 m

-3 N sec 2

CD=for rectangular paddle =1.8 Paddle tip velocity= 0,6m/sec Relative velocity of paddle = 0,75 Vpaddle tip

44

Pneumatic Mixers
When air is injected in mixing tank, power dissipated by the rising air bubbles can be estimated as:
Ref: Reynolds/Richards 2nd Edition

h + 33 .9 P = 35 .28 Q aLn US customary units 33 .9

h + 10 .33 P = 1 .689 Q aLn 10 . 33

SI units

P=power dissipated (ft.Ib/sec OR kW) Qa=air flow rate at operating temperature and pressure ( ft3/min or m3/min ) H=depth to the diffusers in meters of water (air pressure at the point of discharge) 45 (ft or m )

Application of pneumatic mixing:

to provide oxygen and to maintain mixed liquor necessary for aerobic bacteria in biological treatory to keep bacteria in suspension in biological treatment.

46

Example:
A pneumatic mixing basin with a volume of 6200 ft3 is to be designed to provide G value of 60 sec-1. Assume that the basin depth is to be 12ft and air will be released into the basin 0,5ft above the tank bottom.
(Temp= 60oF
1bf . sec = 2 .359 .10 5 2 ft
Ref: Reynolds/Richards 2nd Edition

47