Scribd
Upload
338 views

3 DOF Gyroscope Courseware Sample For MATLAB Users

simulacija

Uploaded by

Dragan Lazic
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
338 views

3 DOF Gyroscope Courseware Sample For MATLAB Users

simulacija

Uploaded by

Dragan Lazic
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

LABORATORY GUIDE

3 DOF Gyroscope Experiment for MATLAB /Simulink Users


Developed by:
Jacob Apkarian, Ph.D., Quanser
Amirpasha Javid, B. Eng., Quanser
CAPTI VATE. MOTI VATE. GRADUATE.
Quanser educational solutions
are powered by:



PREFACE
Preparing laboratory experiments can be time-consuming. Quanser understands time constraints of teaching
and research professors. Thats why Quansers control laboratory solutions come with proven practical
exercises. The courseware is designed to save you time, give students a solid understanding of various
control concepts and provide maximum value for your investment.
Quanser 3 DOF Gyroscope courseware materials are supplied in a format of the Laboratory Guide. The Lab
Guide contains lab assignments for students.

This courseware sample is prepared for users of The MathWorks MATLAB/Simulink
software in conjunction with Quansers QUARC real-time control software. A version of the
curriculum for National Instruments LabVIEW users is also available.







The following material provides an abbreviated example of in-lab procedures for the 3 DOF Gyroscope
experiment. Please note that the examples are not complete as they are intended to give you a brief
overview of the structure and content of the courseware materials you will receive with the plant.



TABLE OF CONTENTS

PREFACE ...................................................................................................................... PAGE 1
INTRODUCTION TO QUANSER 3 DOF GYROSCOPE COURSEWARE SAMPLE ............. PAGE 3
LABORATORY GUIDE TABLE OF CONTENTS ................................................................ PAGE 3
BACKGROUND SECTION SAMPLE ............................................................................ PAGE 4
LAB EXPERIMENTS SECTION SAMPLE ...................................................................... PAGE 5




1. INTRODUCTION TO QUANSER 3 DOF GYROSCOPE COURSEWARE SAMPLE
Quanser courseware materials provide step-by-step pedagogy for a wide range of control challenges.
Starting with the basic principles, students can progress to more advanced applications and cultivate a
deep understanding of control theories. Quanser 3 DOF Gyroscope courseware covers topics, such as:
Obtain a state-space representation of the open-loop system
Design a state-feedback gain for the closed-loop system using the Linear-Quadratic Regulator
(LQR) optimization
Simulate the system and ensure it is stabilized using the designed state-feedback control
Implement your state-feedback controller on the 3D GYRO system and evaluate its actual
performance


2. LABORATORY GUIDE TABLE OF CONTENTS
The full Table of Contents of the Quanser 3 DOF Gyroscope Laboratory Guide is shown here:
1. INTRODUCTION
2. BACKGROUND
2.1. MODELING
2.1.1. MODEL CONVENTION
2.1.2. EQUATIONS OF MOTION
2.1.3. LINEAR STATE-SPACE MODEL
2.2. CONTROL
2.2.1. STABILITY
2.2.2. CONTROLLABILITY
2.2.3. LINEAR QUADRATIC REGULAR (LQR)
2.2.4. FEEDBACK CONTROL
3. LAB EXPERIMENTS
3.1. SIMULATION
3.1.1. PROCEDURE
3.2. IMPLEMENTATION
3.2.1. PROCEDURE
3.2.2. ANALYSIS
4. SYSTEM REQUIREMENTS
4.1. OVERVIEW OF FILES
4.2. SETUP FOR SIMULATION
4.3. SETUP FOR RUNNING ON 3 DOF GYROSCOPE

REFERENCES




3. BACKGROUND SECTION - SAMPLE
Equations of Motion
The equations of motion representing the angular rate of the red gimbal, , and the outer blue gimbal, ,
are ([1]):

(2.1)
where
J
y
= 0.0036 kgm
2

J
z
= 0.0226 kgm
2

h = 0.44 kgm
2
/s

The moment of inertia about the y-axis angle, , is J
y
and the moment of inertia about the z-axis angle (red
gimbal), , is denoted as J
z
. The constant h is calculated based on the moment of inertia of the gyroscope
rotor about its own axis and its velocity. Because the outer gray rectangular frame is fixed, the only actuated
axis is the y-axis. The control input in the single-input single-output (SISO) system is the torque applied in
the y-axis,
y
.

Linear State-Space Model
The linear state-space equations are
(2.2)
and
(2.3)
where x is the state, u is the control input, A, B, C, and D are state-space matrices.

For this system, the state and output are defined

(2.4)
and

Solving for the acceleration terms in the linear equations of motion given in Equation 2.1 we get


Substituting the state in , we obtain the following state-space matrices:


and





4. LAB EXPERIMENTS SECTION - SAMPLE
Simulation
In this section we will use the Simulink diagram shown in Figure 3.1 to simulate the closed-loop control of
the 3 DOF Gyroscope system. The system is simulated using the model summarized in Section 2.1. The
Simulink model uses the state-feedback control described in Section 2.2.4. The feedback gain K is found
using the Matlab LQR command (LQR is described briefly in Section 2.2.3).

Table 3.1: Simulink model used to simulate the 3 DOF Gyroscope.

IMPORTANT: Before you can conduct these experiments, you need to make sure that the lab files are
configured according to your setup. If they have not been configured already, then you need to go to
Section 4 to configure the lab files first.

Procedure
Follow these steps to simulate the 3 DOF Gyroscope:
1. Make sure the LQR weighting matrices in setup_3dgyro.m are set to










and R=5
2. Run the script to generate the gain

Remark: When tuning the LQR, Q(2; 2) effects the red gimbal proportional gain while Q(1; 1) effects the
red gimbal derivative gain (which reduces the overshoot). Q(4; 4) affects the red gimbal integral gain
which is used to minimize the steady state error.
3. Open the red gimbal position scope, Psi (deg), the torque scope, Torque (N.m).
4. Start the simulation. The scopes should be displaying responses similar to Figure 3.2.





Figure 3.2: Simulated closed-loop response.

Implementation
The q_3dgyro_lqr Simulink diagram shown in Figure 3.3 is used to perform the red gimbal position control
on the 3 DOF Gyroscope. The HIL Interfacing subsystem contains drivers that interface with the DC motor
and sensors of the 3 DOF Gyroscope system.

Figure 3.3: Simulink model used to run controller on the 3 DOF Gyroscope.

IMPORTANT: Before you can conduct these experiments, you need to make sure that the lab files are
configured according to your setup. If they have not been configured already, then you need to go to
Section 4 to configure the lab files first.
Solutions for teaching and research. Made in Canada.
I NFO@QUANSER. COM +1- 905- 940- 3575 QUANSER. COM
Full range of robotic and mechatronic control plants
for teaching and research
Omni Bundle 2 DOF Planar Robot
Hexapod* IMDU Base Unit IMDU-Web Winding
IMDU-Multi DOF Torsion
3 DOF Gyroscope
Active Suspension
* Please note: The Hexapod is not available for purchase in North America, Japan and Taiwan.
Choose from eight plants to create experiments for teaching or research related to robotics, haptics,
mechatronics, aerospace, or process control. For more information please contact info@quanser.com
2013 Quanser Inc. All rights reserved.

You might also like