WE Fasteners

Fasteners
more than you expect

2
Bonding sealing gasket 77
Conical spring washer 76 6796
Cup washer 77
Double serrated lock washer 74
Fender washer 69 9021 7093
Plain washer 68 125 7089 2041
Plain washer (for Al. joints) 75 3738
Spring washer 70 127
Spring washer 70 7980
Star washer 72 6797
Star washer 73 6798
Wave washer 71 137
Wrth-lock washer 78
Washers Page DIN ISO SFS
Flathead 17 7500CE
Hex fange head 16 7500DE
Pan head 15 7500ME
Thread forming screws Page DIN ISO SFS
Plain washer 12 6900-1
Spring washer 13 6900-3
Star washer 14 6900-4
Combination screws Page DIN ISO SFS
Dome head 40 7380
Flat head 38 7991
Socket head cap 36 912 4762 2219
Socket head low cap 37 7984
Socket head low cap 39 6912
Socket hex head screws Page DIN ISO SFS
Full thread 35 933 4017 2064
Partially threaded 34 931 4014 2063
Hex head screws Page DIN ISO SFS
Flat head 25 7982 7050 2760
Hex head 23 7976 1479
Oval head 26 7983 7051 2761
Pan head 24 7981 7049 2759
Sheet metal screw installation information 27-28
Sheet metal screws 32-33
Sheet metal screws Page DIN ISO SFS
Cage nut 63
Cap nut 62 1587
Extension nut 65 6330
Hex jam nut, chamfered 58 439 4035 2068
Hex jam nut, fne thread 57 936
Hex nut 56 934 4032 2067
Lifting eye nut 47 582
Lock nut, all metal form "V" 60 980 V 7042
Nyloc lock nut 59 985 7040
Slab base weld nut 119
Square nut 64 562
T-Nut (4-claw nut) 67 1624
Weld nut 119 3929
Wing nut 66 315
Wlock nut 61
Nuts Page DIN ISO SFS
Slotted set screw with fat point 45 551 4766
Socket set screw with cone point 42 914 4027 4736
Socket set screw with cup point 44 916 4029 4738
Socket set screw with fat point 41 913 4026 4735
Socket set screw with half dog point 43 915 4028 4737
Set screws Page DIN ISO SFS
Dome head 4
Flat head 5
Flange dome head 3
Special screw for thermoplastics 6
Plastofast Page DIN ISO SFS
Flat head 31 7504O 7050
Hex fange head 29 7504K 1479
Round head 30 7504M 7049
Self-drilling screw Page DIN ISO SFS
Flat head 8 965 7046 2977
Oval head 9 966 7047 2978
Pan head 7 7985 7045 2976
Slotted cheese head 10 84 1207 2176
Slotted fat head 11 963 2009 2177
Machine screws Page DIN ISO SFS
Flat head, full thread 50
Flat head, half thread 50
Pan head 49
Multipurpose screws Page DIN ISO SFS
Drop in anchor 53
Hexagon fange bolt 46 6921
Lifting eye bolt 47 580
Nylon plug 51
PFG anchor 53
Split cotter pin 55 94 1234 4909
Spring pin 54 1481 8752
Standard E-type circlip 81 6799
Standard external circlip 79 471-1
Standard internal circlip 80 472-2
Threaded rod 48 975
Wedge anchor 52
Table of content
Blind rivets 112 - 117
High strength stud: WEHFH 99
KALEI nut 107
Rivet nuts 108 - 111
Self-broaching: WEARB and WEARBSO 87
Self-broaching: WEMINARB and WIMINOFF 89
Self-broaching: WEMINLOK 91
Self-clinching fush nut: WEF 101
Self-clinching nut: WES and WECLS 95
Self-clinching standof: WESO and WEBSO 103
Self-clinching studs: WEFH and WEFHS 97
Sheet metal fasteners Page
11.03.2014
DIN = German Institute for Standardization
ISO = International Organization for Standardization
SFS = Finnish Standardization Association
Cast holes 20-21
Collared holes 19
Drilled or punched holes 18
Taptite: Mechanical properties 22
Taptite Page DIN ISO SFS
3
Plastofast
Flange dome head
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 0164 Black passivated steel, pozidriv 01640
Zinc plated steel, torx 0170 Black passivated steel, torx 01700
Nominal diameter d 2.2 2.5 3.0 3.5 4.0 5.0 6.0
Pozidriv size 1 1 2 2 2 2 3
Head height d max 1.6 1.8 2.1 2.4 2.5 3.2 4
Head width dk max 4.4 5 6 7 8 10 12
Length l 5 - 12 5 - 16 6 - 30 8 - 25 8 - 30 10 - 50 12 - 60
Dimension chart 1441
1441
1451
Nominal diameter d 2.2 2.5 3.0 3.5 4.0 5.0 6.0
Torx size 6 6 10 10 20 20 25
Head height d max. 1.4 1.5 2.1 2.1 2.6 3.3 3.6
Head width dk max. 4.5 5.0 6.0 7.0 8.0 10.0 12.0
Length l 5 - 12 5 - 16 6 - 30 8 - 25 8 - 30 10 - 50 12 - 60
4
Plastofast
Dome head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 0165 Black passivated steel, torx 0170 Stainless steel A2, pozidriv 7165
Zinc plated steel, torx 0168 Black passivated steel, pozidriv 01650
1442
1452
Nominal diameter d 1.8 2.2 2.5 3.0 3.5 4.0 5.0 6.0
Pozidriv size 0 1 1 2 2 2 2 3
Head height d max. 1.2 1.5 1.7 2.0 2.5 2.7 3.4 4.0
Head width dk max. 3.2 3.9 4.4 5.3 6.1 7 8.8 10.5
Length l 4 - 10 5 - 16 5 - 20 6 - 30 7 - 35 8 - 35 10 - 40 12 - 60
Pozidriv size 6 6 8 10 10 20 20 25
Head height d max. 1.3 1.4 1.6 2.1 2.3 2.6 2.9 3.8
Head width dk max. 3.6 4.0 4.2 5.6 6.9 7.5 8.2 10.8
Length l 5 - 10 5 - 16 5 - 16 6 - 16 8 - 30 8 - 30 10 - 30 12 - 50
Dimension chart 1452 (1449)
5
Plastofast
Flat head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 0166 Black passivated steel, torx 2166 Stainless steel A2, pozidriv 7166
Zinc plated steel, torx 0166 Black passivated, pozidriv 01660
1413
1423
Pozidriv size 6 6 8 10 10 20 20 25
Head height d max. 1.3 1.4 1.6 2.1 2.3 2.6 2.9 3.8
Head width dk max. 3.6 4.0 4.2 5.6 6.9 7.5 8.2 10.8
Length l 5 - 10 5 - 16 5 - 16 5 - 16 8 - 30 8 - 30 10 - 30 12 - 50
Pozidriv size 6 6 8 8 15 20 20 30
Head height k max. 1.1 1.3 1.7 1.7 2.2 2.3 2.5 3.6
Head width dk max. 3.4 3.8 4.7 5.5 7.3 8.4 9.3 11.3
Length l 5 - 10 6 - 12 6 - 20 8 - 20 10 - 25 8 - 30 10 - 40 12 50
6
Material
Hole
mm
External
mm
Screw depth
mm
ABS Acrylonitrile / Butadiene / Styrene 0.80 x d 2.00 x d 2.00 x d
ABS / PC blend Acrylonitrile / Styrene / Acrylester 0.80 x d 2.00 x d 2.00 x d
ASA Polyamide 0.78 x d 2.00 x d 2.00 x d
PA 4.6 0.73 x d 1.85 x d 1.80 x d
PA 4.6 - GF 30 0.78 x d 1.85 x d 1.80 x d
PA 6 0.75 x d 1.85 x d 1.70 x d
PA 6 - GF 30 0.80 x d 2.00 x d 1.90 x d
PA 6.6 0.75 x d 1.85 x d 1.70 x d
PA 6.6 - GF 30 0.82 x d 2.00 x d 1.80 x d
PBT Polybutylene terephthalate 0.75 x d 1.85 x d 1.70 x d
PBT - GF 30 0.80 x d 1.80 x d 1.70 x d
PC Polycarbonate 0.85 x d 2.50 x d 2.20 x d
PC - GF 30 0.85 x d 2.20 x d 2.20 x d
LDPE Polyethylene 0.70 x d 2.00 x d 2.00 x d
HDPE 0.75 x d 1.80 x d 1.80 x d
PET Polyethylene terephthalate 0.75 x d 1.85 x d 1.70 x d
PET - GEF 30 0.80 x d 1.80 x d 1.70 x d
PMMA Polymethyl methacrylate 0.85 x d 2.00 x d 2.00 x d
POM Polyethylene oxide 0.75 x d 1.95 x d 2.00 x d
PP Polypropene 0.70 x d 2.00 x d 2.00 x d
PP - TV 20 0.72 x d 2.00 x d 2.00 x d
PPO Polyphenylene oxide 0.85 x d 2.50 x d 2.20 x d
PS Polystyrene 0.80 x d 2.00 x d 2.00 x d
PVC (kova) Polyvinyl chloride 0.80 x d 2.00 x d 2.00 x d
SAN Styrene / Acrylonitrile 0.77 x d 2.00 x d 1.90 x d
Plastofast
Specially threaded screws for thermoplastics
Recommended sizes:
Recommended dimen-
sions for attachment
7
Machine screw
Pan head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.8, pozidriv 6046 Stainless steel A2, pozidriv 7046 Magnetic stainless steel A2 8046
Zinc plated steel 4.8, torx 2046 Stainless steel A2, torx 70462 Acid proof steel A4, pozidriv 2002
Black passivated steel 4.8, pozidriv 60464 Waxed stainless steel A2
Nominal diameter d M1.6 M2 M2.5 M3 (M3.5) M4 M5 M6 M8 M10
Pozidriv size 0 1 1 1 2 2 2 3 4 4
Torx size 5 6 8 10 15 20 25 30 40 50
Head height d max. 1.42 1.72 2.12 2.52 2.82 3.25 3.95 4.75 6.15 7.68
Head width dk max. 3.2 4.0 5.0 6.0 7.0 8.0 10.0 12.0 16.0 20.0
Length l (full thread) 2 - 16 2 - 18 3 - 20 4 - 22 5 - 22 5 - 25 6 - 28 10 - 35 10 - 40 12 - 45
Length l (half thread) 20 22 - 30 25 - 30 25 - 35 28 - 40 30 - 50 40 - 50 45 - 60 50 - 60
Dimension chart DIN 7985
DIN 7985
SFS 2976
ISO 7045
ISO 14583 TX
Pozidriv size 0 0 1 1 2 2 2 3 4 4
Torx size 5 6 8 10 15 20 25 30 45 50
Head height d max. 1.3 1.6 2.1 2.4 2.6 3.1 3.7 4.6 6.0 7.5
Head width dk max. 3.2 4.0 5.0 5.6 7.0 8.0 9.5 12.0 16.0 20.0
Length l (half thread) 30 45 45 - 60 45 - 60 45 - 60
Dimension chart ISO 7045 / ISO 14583 TX
Please mark your order either as DIN 7985 or ISO 7045.
8
Machine screw
Flat head
DIN 965
SFS 2977
ISO 7046
ISO 14581 TX
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.8, pozidriv 6048 Stainless steel A2, pozidriv 7048 Black passivated steel 4.8, pozidriv 60484
Zinc plated steel 4.8, slot 1039 Stainless steel A2, torx 70484 Acid proof A4, pozidriv 6003
Zinc plated steel, torx 2048
Pozidriv size 0 1 1 1 2 2 2 3 4 4
Torx size 6 8 10 15 20 25 30 45
Head height k max. 0.96 1.20 1.50 1.65 1.93 2.20 2.50 3.00 4.00 5.00
Head width dk max. 3.0 3.8 4.7 5.6 6.5 7.5 9.2 11.0 14.5 18.0
Pozidriv size 0 0 1 1 2 2 2 3 4 4
Torx size 6 8 10 15 20 25 30 45
Head height k max. 1.0 1.2 1.5 1.65 2.35 2.7 2.7 3.3 4.65 5,0
Head width dk max. 3.0 3.8 4.7 5.5 7.3 8.4 9.3 11.3 15.8 18.3
Length l (half thread) 50 50 - 60 50 - 60 50 - 60
9
Machine screw
Oval head
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.8, pozidriv 6049 Acid proof A4, pozidriv 5003
Black passivated steel 4.8, pozidriv 60494 Stainless steel A2, pozidriv 7049
Nominal diameter d M 1.6 M2 M2.5 M3 (M3.5) M4 M5 M6 M8 M10
Pozidriv size 0 1 1 1 2 2 2 3 4 4
Torx size 10 20 25 30
Head height k max. 0.96 1.20 1.50 1.65 1.93 2.20 2.50 3.00 4.00 5.00
Head width dk max. 3,0 3.8 4.7 5.6 6.5 7.5 9.2 11.0 14.5 18.0
DIN 966
SFS 2978
ISO 7047
Pozidriv size 0 0 1 1 2 2 2 3 4 4
Torx size 10 20 25 30
Head height k max. 1.0 1.2 1.5 1.65 2.35 2.7 2.7 3.3 4.65 5.0
Head width dk max. 3.0 3.8 4.7 5.5 7.3 8.4 9.3 11.3 15.8 18.3
Length l (half thread) 50 50 - 60 50 - 60 50 - 60
Dimension chart ISO 7047
10
Machine screw
Slotted cheese head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.8 0040 Brass 0017 Stainless steel A2 7040
Black passivated steel 4.8 2040 Polyamide 0278 Acid proof steel A4 1002
DIN 84
SFS 2176
ISO 1207
Nominal diameter d M1 M1.2 M1.4 M1.6 (M 1.8) M2 M2.5 M3 (M 3.5) M4 M5 M6 M8 M10
Slot width n 0.25 0.3 0.3 0.4 0.4 0.5 0.6 0.8 1 1.2 1.2 1.6 2 2.5
Head height d max 0.7 0.8 0.9 1.0 1.2 1.3 1.6 2.0 2.4 2.6 3.3 3.9 5.0 6.0
Head width dk max 2.0 2.3 2.6 3.0 3.4 3.8 4.5 5.5 6.0 7.0 8.5 10.0 13.0 16.00
Length l (full thread) 2 10 2 12 2 14 2 16 2 18 3 20 3 25 4 30 5 35 5 40 6 40 8 40 10 40 12 40
Length l (half thread) 45 50 45 60 45 80 45 80
Slot width n 0.4 0.5 0.6 0.8 1.0 1.2 1.2 1.6 2 2.5
Head height d max. 1.1 1.4 1.8 2.0 2.4 2.6 3.3 3.9 5.0 6.0
Head width dk max. 3.0 3.8 4.5 5.5 6.0 7.0 8.5 10.0 13.0 16.00
Length l (full thread) 2 16 3 20 3 25 3 25 4 30 5 40 6 40 8 40 10 40 12 40
Length l (half thread) 45 50 45 60 45 80 45 80

11
Machine screw
Slotted fat head
DIN 963
SFS 2177
ISO 2009
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.8 0039 Brass 4039 Stainless steel A2 7039
Polyamide 3278 Acid proof A4 1003
Nominal diameter d M1 M1.2 M1.4 M1.6 M2 M2.5 M3 (M 3.5) M4 M5 M6 M8
Slot width n 0.25 0.3 0.3 0.4 0.5 0.6 0.8 0.8 1 1.2 1.6 2
Head height d max. 0.60 0.72 0.84 0.96 1.20 1.50 1.65 1.93 2.20 2.50 3.0 4.0
Head width dk max. 1.9 2.3 2.6 3.0 3.8 4.7 5.6 6.5 7.5 9.2 11.0 14.5
Length l (full thread) 2 10 3 18 3 20 4 22 4 25 5 25 6 30 8 35 10 40
Length l (half thread) 2 5 2 6 2 10 22 25 25 30 28 35 28 40 35 50 40 50 45 55
Nominal diameter d M10 M12 (M14) M16 (M18) M20
Slot width n 2.5 3 3.0 4.0 4.0 5.0
Head height d max. 5.0 6.0 7.0 8.0 9.0 10.0
Head width dk max. 18.00 22.00 25.0 29.0 33.0 36.0
Length l (full thread) 12 50 20 60 22 60 25 70 25 80 30 80
Length l (half thread) 55 60 70 80 70 80 80 100 90 100 90 100
Slot width n 0.4 0.5 0.6 0.8 1.0 1.2 1.2 1.6 2 2.5
Head height d max. 1.00 1.20 1.50 1.65 2.35 2.70 2.70 3.30 4.65 5.00
Head width dk max. 3.0 3.8 4.7 5.5 7.3 8.4 9.3 11.3 15.8 18.30
Length l (full thread) 2.5 16 3 20 4 25 5 30 6 35 6 40 8 45 8 45 10 45 12 45
Length l (half thread) 50 50 60 50 80 50 80
12
Combination screw
Plain washer
Material
Prod.
group
Zinc plated steel 0000
DIN 6900-1
Dimension chart
Length l 2 min. is the minimum efective Length that is possible to manufacture as a combination screw.
Nominal diameter d 2.5 3 (3.5) 4 5 6 8 10 12
Gap a max. 0.9 1 1.2 1.4 1.6 2 2.5 3 3.5
Length l 2 min. 4 4 6 6 6 8 10 12 14
Washer DIN 6902
Shape C
Mark 0
h 0.6 0.6 0.8 0.8 1 1.6 2 2.5 3
d2 5 6 7 8 9 11 15 18 20
Shape A
Mark 1
h 0.6 0.6 0.8 0.8 1 1.6 2 2.5 3
d2 6 7 8 9 10 12 16 20 24
Shape B
Mark 2
h 0.8 0.8 0.8 1 1.6 1.6 2 2.5 3
d2 8 9 11 12 15 18 24 30 37
This type of combination screw is ftted with a plain washer DIN 6902, which has hardness of 200 - 250 HV. The washer is
attached to the screw before threading in order to let the washer turn freely without detaching. The combination screw has to
meet the following requirements: The bottom face of the head must be level, nominal diameter needs to be between M2.5 -
M12 and the material strength has to be, according to ISO 898, at most 10.9.
13
Combination screw
Spring washer
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.8, pozidriv 90469 Steel 4.8, delta torx 904677
Dimension chart
Length l 2 min. is the minimum efective length that is possible to manufacture as a combination screw.
Nominal diameter d M2.5 M3 M(3.5) M4 M5 M6 M8 M10 M12
Gap a max. 0.9 1 1.2 1.4 1.6 2 2.5 3 3.5
Length l 2 min. 4 4 6 6 6 8 10 12 14
Washer DIN 6902
Shape C
Mark 0
h 0.6 0.6 0.8 0.8 1 1.6 2 2.5 3
d2 6 7 8 9 10 12 16 20 24
Shape A
Mark 1
h 0.8 0.8 0.8 1 1.6 1.6 2 2.5 3
d2 8 9 11 12 15 18 24 30 37
Spring washer DIN 6905
Shape B
Mark 2
h 1.1 1.3 1.3 1.4 1.7 2.2 2.75 3.15 3.65
d2 4.55 5.6 6.1 6.95 8.55 11 13.95 16.95 19.7
This type of combination screw is ftted with a spring washer DIN 6905 following DIN 267-26 technical delivery conditions.
A plain washer DIN 6902 with hardness of 200-250 HV can also be attached, if so required. The washer(s) is attached to the
screw before threading in order to let the washer(s) turn freely without detaching. The combination screw has to meet the fol-
lowing requirements: The bottom face of the head must be level, nominal diameter needs to be between M2.5 - M12 and the
material strength has to be, according to ISO 898, less than 8.8.
DIN 6900-3
14
Combination screw
Star washer
Material
Prod.
group
Dimension chart
Length l 2 min is the minimum efective Length that is possible to manufacture as a combination screw.
Nominal diameter d M2.5 M3 M(3.5) M4 M5 M6 M8 M10
Gap a max 0.9 1 1.2 1.4 1.6 2 2.5 3
Length l 2 min 4 4 6 6 6 8 10 12
Washer DIN 6907 Mark 7
h 1.2 1.2 1.5 1.5 1.8 2.1 2.4 2.7
d2 5.5 6 7 8 9 11 14 18
This type of combination screw is ftted with a star washer DIN 6907. The washer is attached to the screw before threading in
order to let the washer turn freely without detaching. The combination screw has to meet the following requirements: The bot-
tom face of the head must be level, nominal diameter needs to be between M2.5 - M10 and the material strength has to be,
according to ISO 898, less than 5.8.
DIN 6900-4
15
Thread forming screw
Pan head
Nominal diameter d M2 M2.5 M3 (M3.5) M4 M5 M6 M8 M10
Slot size 1 1 1 2 2 2 3 4 4
Torx size 6 8 10 15 20 25 30 40 50
Head height k 1.72 2.12 2.52 2.82 3.25 3.95 4.75 6.15 7.68
Head diameter dk max. 4.0 5.0 6.0 7.0 8.0 10.0 12.0 16.0 20.0
length l, recommendation 3 - 16 4 - 20 4 - 25 5 - 29 6 - 30 8 - 40 8 - 50 10 - 60 12 - 80
Tapping length, max. recommended 1.6 1.8 2.0 2.4 2.8 3.2 4.0 5.0 6.0
DIN 7500ME
First 4 leads in the lower part of the shank have been specially designed to form threads.
Slot size 0 1 1 2 2 2 3 4 4
Torx size 6 8 10 15 20 25 30 45 50
Head height k 1.6 2.1 2.4 2.6 3.1 3.7 4.6 6.0 7.5
Tapping length, max. recommended 3 - 16 4 - 20 4 - 25 5 - 29 6 - 30 8 - 40 8 - 50 10 - 60 12 - 80
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 0209 Zinc plated steel, torx 2209 Stainless steel 7209
16
Flange hex head
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 02093 Stainless steel 7209
DIN 7500DE
Dimension chart DIN 933 and ISO 4017
Please mark your order, in case of M10, either as DIN 933 or ISO 4017.
Nominal diameter d M2 M2.5 M3 (M3.5) M4 M5 M6 M8 M10 M10
DIN ISO
Width across fats s 4 5 5.5 6 7 8 10 13 17 16
Head height k 1.4 1.7 2 2.4 2.8 3.5 4 5.3 6.4 6.4
Head diameter e max. 4.32 5.45 6.01 6.58 7.66 8.79 11.05 14.38 19.60 18.50
Tapping length, max. recommended 3 - 16 4 - 20 4 - 25 5 - 29 6 - 30 8 - 40 8 - 50 10 - 60 12 - 80 12 - 80
17
Flat head
DIN 7500 CE
Pozidriv size 1 1 1 2 2 2 3 4 4
Torx size 6 8 10 15 20 25 30 40 50
Head height k 1.20 1.50 1.65 1.93 2.20 2.50 3.00 4.00 5.00
Tapping length, max. recommended 3 - 16 4 - 20 4 - 25 5 - 29 6 - 30 8 - 40 8 - 50 10 - 60 12 - 80
Pozidriv size 0 1 1 2 2 2 3 4 4
Torx size 6 8 10 15 20 25 30 45 50
Head height k 1.2 1.5 1.65 2.35 2.7 2.7 3.3 4.65 5.0
length l, recommendation 3 - 16 4 - 20 4 - 25 5 - 29 6 - 30 8 - 40 8 - 50 10 - 60 12 - 80
Tapping length, max. recommended 1.6 1.8 2.0 2.4 2.8 3.2 4.0 5.0 6.0
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 02096 Stainless steel A2 7209 Zinc plated steel, torx 2209
18
Material thickness or grip length
0.5 - 1.5 1.5 - 2.5 2.5 - 4.0 4.0 - 6.3 6.3 - 10 10-
Thread Hole diameter D mm
M3 2.70 2.75 2.75 2.80 2.80
M4 3.60 3.60 3.65 3.70 3.70
M5 4.55 4.60 4.65 4.65
M6 5.45 5.50 5.55 5.55 5.65
M8 7.30 7.40 7.40 7.55
M10 9.20 9.25 9.25 9.45
Taptite thread forming screws
Drilled or punched holes
Drille or punched holes in carbon steel with hardness of HB 110-130.
If the sheet thickness is bigger than the diameter of the thread, choosing the proper
sized mounting hole ensures the strongest possible joining and locking.
Material thickness or grip length
0.5 - 1.5 1.5 - 2.5 2.5 - 4.0 4.0 - 6.3 6.3 - 10 10-
Thread Hole diameter D mm
M3 2.70 2.70 2.75 2.80 2.80
M4 3.60 3.60 3.60 3.65 3.70
M5 4.55 4.55 4.60 4.65
M6 5.45 5.45 5.50 5.50 5.55
M8 7.30 7.35 7.40 7.45
M10 9.20 9.20 9.25 9.35
Drilled or punched holes in HB 80 - 120 light metal.
19
Thread
Hole diameter D mm
H11
M3 2.70
M4 3.60
M5 4.55
M6 5.40
M8 7.30
M10 9.15
Collared holes
Collared holes in carbonsteel
with hardness of HB 110-130
Material thickness t mm
less than 1 1.0 - 1.5 1.5 - 2.0 2.0 - 2.5 2.5 - 3.0 3.0 - 4.0
Thread Collar height H mm
M3 1.2 1.2 1.3 1.3
M4 1.3 1.4 1.5 1.5 1.6
M5 1.6 1.8 2.0 2.3 2.5
M6 1.9 2.1 2.4 2.6 2.8
M8 2.6 3.0 3.2 3.5
M10 3.7 3.9 4.3
Hole collar dimensions
D
H
t
20
Holes in cast alloys
Hole diameter d k L
Thread D
2
D
3
min min min
M3 2.8 2.6 5 7 6
M4 3.8 3.5 7 9 8
M5 4.7 4.5 9 11 10
M6 5.7 5.4 10 13 12
M8 7.7 7.3 14 17 16
M10 9.6 9.1 17 21 20
Cast holes
These recommendations are for resilient cast alloys, such as aluminium,
brass and zinc.
For fragile cast alloys, the hole dimensions has to be sampled invidu-
ally.
L
min 0.8
K
S
D
2
d
D
3
Cone
130
L = The grip depth of an equally strong joint.
21
Holes in cast alloys
Thread D
S
min
K
min
L
min
M3 2.75 1.5 7 6
M4 3.65 2 9 8
M5 4.55 3 11 10
M6 5.45 3.2 13 12
M8 7.40 3.7 17 16
M10 9.30 4 21 20
Drilled holes
These recommendations are for resilient cast alloys, such as alumini-
um, brass and zinc.
For fragile cast alloys, the hole dimensions has to be sampled invidu-
ally.
L
min 0.8
K
S
D
L = The grip depth of an equally strong joint.
22
Mechanical properties according to ISO 7085:1999.
When tapping the neccessary force required is always less than the tensile strength of the screw.
The size of the mounting hole, precision, material properties and lubrication method afects the tapping torque.
The pull-through strength value in the following chart is an directional value, not a constant value set by the ISO standard.
Case hardened self-tapping screws has to be marked with a - 0- marking.
The mark is mandatory in socket and hex head screws with nominal diameter M5 or larger.
If separately requested, this mark can also be put in smaller or diferent types of screws.
Nominal
diameter
mm
Tapping
torque MAX
Nm
Torsional strip-
ping strength
MIN Nm
Pull-out force
x) MIN N
2 0.3 0.5 1940
2.5 0.6 1.2 3150
3 1.1 2.1 4680
3.5 1.7 3.4 6300
4 2.5 4.9 8170
5 5.0 10.0 13200
6 8.5 17.0 18700
8 21.0 42.0 34000
10 43.0 85.0 53900
12 75.0 150.0 78400
x) additional information
23
Self-tapping sheet metal screw
Hex head
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, sharp type C 0114 Stainless steel A2, sharp type C 7114
DIN 7976
ISO 1479
Thread ST 2.2 ST 2.9 ST 3.5 ST (3.9) ST 4.2 ST 4.8 ST (5.5) ST 6.3 ST (8.0)
Width across fats s 3.2 5.0 5.5 7.0 7.0 8.0 8.0 10.0 13.0
Head height k max. 1.42 1.62 2.42 2.42 2.92 3.12 4.15 4.95 5.95
Head diameter e min. 3.38 5.40 5.96 7.59 7.59 8.71 8.71 10.95 14.26
Length l 4.5 - 13 6.5 - 19 9.5 - 25 9.5 - 25 9.5 - 32 9.5 - 50 13 - 50 13 - 50 16 - 50
Thread ST 2.2 ST 2.9 ST 3.5 ST 4.2 ST 4.8 ST 5.5 ST 6.3 ST 8.0 ST 9.5
Width across fats s 3.2 5.0 5.5 7.0 8.0 8.0 10.0 13.0 16.0
Head height k max. 1.6 2.3 2.6 3.0 3.8 4.1 4.7 6.0 7.5
Head diameter e min. 3.38 5.40 5.96 7.59 8.71 8.71 10.95 14.26 17.6
Length l 4.5 - 16 6.5 - 19 6.5 - 22 9.5 - 25 9.5 - 32 13 - 32 13 - 38 13 - 50 16 - 50
Type C Type F
24
Pan head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, PZ sharp type C 6115 Zinc plated steel, PZ fat type F 61152 Zinc plated steel, knurled 1115
Black passivated steel, PZ sharp type C 61151 Black passivated steel, PZ fat type F 6115 Zinc plated steel, torx 4115
Stainless steel A2, PZ sharp type C 7115 Stainless steel A2, PZ fat type F 71151 Acid proof A4 steel, PZ 1004
DIN 7981
SFS 2759
ISO 7049
ISO 14585 TX
Type C
Type F
Thread ST 2.2 ST 2.9 ST 3.5 ST (3.9) ST 4.2 ST 4.8 ST 5.5 ST 6.3
Torx size 6 10 10 20 20 25 25 30
Head height k max. 1.80 2.20 2.60 2.80 3.05 3.55 3.95 4.55
Head diameter dk max. 4.2 5.6 6.9 7.5 8.2 9.5 10.8 12.5
Length l 4.5 - 16 6.5 - 19 9.5 - 25 9.5 - 25 9.5 - 32 9.5 - 38 13 - 38 13 - 38
Pozidriv size 0 1 2 2 2 3 3 4 4
Torx size 6 10 15 20 25 25 30
Head height k max. 1.6 2.4 2.6 3.1 3.7 4.0 4.6 6.0 7.5
Length l 4.5 - 16 6.5 - 19 9.5 - 25 9.5 - 32 9.5 - 38 13 - 38 13 - 38 16 - 50 16 - 50
25
Flat head
DIN 7982
SFS 2760
ISO 7050
ISO 14586 TX
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated Steel, PZ sharp type C 6116 Stainless steel A2, PZ sharp type C 7116 Acid proof A4, PZ sharp type C 2005
Zinc plated steel, PZ fat type F 6116 Stainless steel A2, PZ fat type F 71161 Acid proof A4, PZ fat type F 2005
Black passivated, PZ sharp type C 6116
Torx size 6 10 15 20 25 25 30
Head height k
~
1.3 1.7 2.1 2.3 2.5 3.0 3.4 3.8
Length l 6.5 - 16 6.5 - 19 9.5 - 25 9.5 - 25 9.5 - 32 9.5 - 32 13 - 38 13 - 38
Pozidriv size 0 1 2 2 2 3 3 4 4
Torx size
Head height k
~
1.10 1.70 2.35 2.60 2.80 3.00 3.15 4.65 5.25
Length l 4.5 - 16 6.5 - 19 9.5 - 25 9.5 - 32 9.5 - 32 13 - 38 13 - 38 16 - 50 16 - 50
Type C
Type F
26
Oval head
DIN 7983
SFS 2761
ISO 7051
Type C
Type F
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, PZ sharp type C 6117 Stainless steel A2, PZ sharp type C 7117 Acid proof A4, PZ sharp type C 1005
Black passivated, PZ sharp type C 6117 Stainless steel A2, PZ fat type F 7117 Acid proof A4, PZ fat type F 1005
Zinc plated steel, PZ fat type F 6117
Torx size 6 10 15 20 25 25 30
Head height k
~
1.3 1.7 2.1 2.3 2.5 3.0 3.4 3.8
Length l 6.5 - 16 6.5 - 19 9.5 - 25 9.5 - 25 9.5 - 32 9.5 - 32 13 - 38 13 - 38
Pozidriv size 0 1 2 2 2 3 3 4 4
Torx size
Head height k
~
1.10 1.70 2.35 2.60 2.80 3.00 3.15 4.65 5.25
Length l 4.5 - 16 6.5 - 19 9.5 - 25 9.5 - 32 9.5 - 32 13 - 38 13 - 38 16 - 50 16 - 50
27
Hole type A Hole type B
Mount holes for sheet metal screws and min. torque
Sheet metal screw
Zinc plated steel
Sheet metal screw
A2 / A4
Opening
Torque
MIN Nm
Sheet thickness
Sheet: St, brass, CU
HB max 120 1)
Sheet: Al Sheet: St 37 Sheet: Al
Thread T mm A / d2 B / d2 A /d2 B / d2 B / d2 B / d2 d4
ST 2.2
0.56 1.60
2.8 0.45
0.56 - 0.75 1.70 1.60
0.75 - 0.88 1.80 1.60
0.88 - 1.13 1.85 1.60
1.13 - 1.38 1.85 1.70
1.38 - 1.50 1.90 1.80
ST 2.9
0.56 2.20 2.20
3.6 1.5
0.56 - 0.63 2.50 2.25 2.20 2.30 2.40
0.63 - 0.75 2.50 2.25 2.20 2.20 2.30 2.40
0.75 - 0.88 2.50 2.40 2.20 2.20 2.30 2.40
0.88 - 1.25 2.40 2.20 2.20 2.30 2.40
1.25 - 1.38 2.40 2.20 2.30 2.40
1.38 - 1.75 2.50 2.25 2.30 2.40
1.75 - 2.50 2.60 2.40 2.40 2.50
ST 3.5
0.56 2.80 2.60 2.70 2.80
4.2 2.7
0.56 - 0.75 2.80 2.70 2.80 2.70 2.80
0.75 - 0.88 2.80 2.70 2.80 2.65 2.70 2.80
0.88 - 1.25 2.80 2.80 2.65 2.70 2.80
1.25 - 1.38 2.80 2.65 2.70 2.80
1.38 - 1.75 2.90 2.75 2.80 2.90
1.75 - 2.50 3.00 2.85 2.80 2.90
2.50 - 3.00 3.20 3.00 2.90 3.00
3.00 - 3.60 3.00 2.90 3.00
ST 3.9
0.50 3.00 2.95 3.00 3.10
4.8 3.4
0.50 - 0.63 3.00 2.95 3.00 3.00 3.10
0.63 - 0.88 3.00 2.95 3.00 2.90 3.00 3.10
0.88 - 1.13 3.00 2.95 3.00 2.95 3.00 3.10
1.13 - 1.25 3.00 3.00 3.00 2.95 3.00 3.10
1.25 - 1.38 3.00 2.95 3.00 3.10
1.38 - 1.75 3.20 3.00 3.00 3.10
1.75 - 2.00 3.20 3.50 3.00 3.10
2.00 - 2.50 3.50 3.50 3.10 3.20
2.50 - 3.50 3.60 3.50 3.20 3.30
The tolerance of the holes is H12. If H13 is used, the holes must be 0.1 mm smaller.
1) If the hardness of the sheet is higher than HB120, 0.1 - 0.2 mm is added to the values in this table.
28
Hole type A Hole type B
Sheet metal mount holes and min. torque
Sheet metal screw
Zinc plated steel
Sheet metal screw
A2 / A4
Opening
Torque
MIN Nm
Sheet thickness
Sheet: St, brass, CU
HB max 120 1)
Sheet: Al Sheet: St 37 Sheet: Al
Thread T mm A / d2 B / d2 A /d2 B / d2 B / d2 B / d2 d4
ST 4.2
0.50 3.50
5 4.4
0.50 - 0.63 3.50 3.20 3.50
0.63 - 0.88 3.50 3.20 3.50 2.95
0.88 - 1.13 3.50 3.20 3.50 3.00 3.20 3.30
1.13 - 1.38 3.50 3.30 3.50 3.20 3.20 3.30
1.38 - 2.50 3.50 3.50 3.30 3.40
2.50 - 3.00 3.80 3.70 3.30 3.40
3.00 - 3.50 3.90 3.80 3.40 3.50
3.50 - 10.00 3.90 3.5 - 3.6 3.6 - 3.7
ST 4.8
0.50 4.00
5.8 6.3
0.50 - 0.75 4.00 3.70 4.00
0.75 - 1.13 4.00 3.70 4.00 3.70
1.13 - 1.38 4.00 3.90 4.00 3.70 3.70 3.90
1.38 - 1.75 3.90 3.70 3.70 3.90
1.75 - 2.50 4.00 3.80 3.80 3.90
2.50 - 3.00 4.10 3.80 3.80 3.90
3.00 - 3.50 4.30 3.90 3.90 4.00
3.50 - 4.00 4.40 3.90 3.90 4.00
4.00 - 4.75 4.40 4.00 4.00 4.10
4.75 - 10.00 4.20 4.1 - 4.2 4.2 - 4.3
ST 5.5
1.13 4.70 4.20
6.6 10
1.13 - 1.38 4.70 4.30 4.10
1.38 - 1.50 4.30 4.10
1.50 - 1.75 4.50 4.20
1.75 - 2.25 4.60 4.40 4.50 4.60
2.25 - 3.00 4.70 4.60 4.50 4.60
3.00 - 3.50 5.00 4.60 4.60 4.70
3.50 - 4.00 5.00 4.80 4.60 4.70
4.00 - 4.75 5.10 4.80 4.70 4.80
4.75 - 10.00 4.90 4.7 - 4.9 4.8 - 4.0
ST 6.3
1.38 5.30 4.90
7.4 13.6
1.38 - 1.75 5.00 5.00
1.75 - 2.00 5.20 5.00
2.00 - 3.00 5.30 5.20 5.30 5.40
3.00 - 4.00 5.80 5.30 5.40 5.50
4.00 -4.75 5.90 5.40 5.50 5.60
4.75 - 5.00 5.60 5.50 5.60
5.00 - 10.00 5.80 5.6 - 5.7 5.7 - 5.8
The tolerance of the holes is H12. If H13 is used, the holes must be 0.1 mm smaller.
1) If the hardness of the sheet is higher than HB120, 0.1 - 0.2 mm is added to the values in this table.
29
Self-drilling screw
Hex fange head
Thread ST 2.9 ST 3.5 ST (3.9) ST 4.2 ST 4.8 ST (5.5) ST 6.3
Drilling diameter 0.7 1.9 0.7 2.25 0.7 2.4 1.75 - 3 1.75 4.4 1.75 5.25 2 - 6
Drill diameter 2.3 2.8 3.1 3.6 4.1 4.8 5.8
Width across fats s 5.0 5.5 7.0 7.0 8.0 8.0 10.0
Head height k max. 1.62 2.42 2.42 2.92 3.12 4.15 4.95
Head diameter e max. 5.40 5.96 7.59 7.59 8.71 8.71 10.95
Length l 9.5 - 19 9.5 - 25 13 - 38 13 - 38 13 - 50 16 - 50 19 - 50
Dimension chart DIN 7504K
Thread ST 2.9 ST 3.5 ST 4.2 ST 4.8 ST 5.5 ST 6.3
Drilling diameter 0.7 1.9 0.7 2.25 1.75 - 3 1.75 4.4 1.75 5.25 2 - 6
Drill diameter 2.3 2.8 3.6 4.1 4.8 5.8
Width across fats s 5.0 5.5 7.0 8.0 8.0 10.0
Head height k max. 2.3 2.6 3.0 3.8 4.1 4.7
Head diameter e max. 5.40 5.96 7.59 8.71 8.71 10.95
Length l 9.5 - 19 9.5 - 25 13 - 38 13 - 50 16 - 50 19 - 50
Please mark your order either as DIN 7504K or ISO 15480.
DIN 7504K
ISO 15480
Material
Prod.
group
30
Self-drilling screw
Pan head
Thread ST 2.9 ST 3.5 ST (3.9) ST 4.2 ST 4.8 ST 5.5 ST 6.3
Drill diameter 2.3 2.8 3.1 3.6 4.1 4.8 5.8
Torx size
Head height k max. 2.20 2.60 2.80 3.05 3.55 3.95 4.55
Head diameter dk max. 5.6 6.9 7.5 8.2 9.5 10.8 12.5
Length l 9.5 - 19 9.5 - 25 13 - 38 13 - 38 13 - 50 16 - 50 19 - 50
Dimension chart DIN 7504N
Please mark your order either as DIN 7504N or ISO 15481.
DIN 7504N
ISO 15481
Material
Prod.
group
Zinc plated steel, pozidriv 0211
Drilling diameter 0.7 1.9 0.7 2.25 1.75 - 3 1.75 4.4 1.75 5.25 2 - 6
Drill diameter 2.3 2.8 3.6 4.1 4.8 5.8
Pozidriv size 1 2 2 2 3 3
Torx size
Head height k max. 2.4 2.6 3.1 3.7 4.0 4.6
Head diameter dk max. 5.6 7.0 8.0 9.5 11.0 12.0
Length l 9.5 - 19 9.5 - 25 13 - 38 13 - 50 16 - 50 19 - 50
31
Self-drilling screw
Flat head
Thread ST 2.9 ST 3.5 ST (3.9) ST 4.2 ST 4.8 ST 5.5 ST 6.3
Drill diameter 2.3 2.8 3.1 3.6 4.1 4.8 5.8
Torx size
Head height k
~
1.7 2.1 2.3 2.5 3.0 3.4 3.8
Length l 13 - 19 13 - 25 13 - 38 13 - 38 16 - 50 19 - 50 19 - 50
Dimension chart DIN 7504P
Please mark your order either as DIN 7504P or ISO 15482.
DIN 7504P
ISO 15482
Material
Prod.
group
Drilling diameter 0.7 1.9 0.7 - 2.25 1.75 - 3 1.75 4.4 1.75 5.25 2 - 6
Drill diameter 2.3 2.8 3.6 4.1 4.8 5.8
Torx size
Head height k
~
1.70 2.35 2.60 2.80 3.00 3.15
Head diameter dk max. 5.5 7.3 8.4 9.3 10.3 11.3
Length l 13 - 19 13 - 25 13 - 38 16 - 50 19 - 50 19 - 50
32
Wronic screw
Truss head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, Phillips 2131 Zinc plated steel, sharp Phillips 1131 Stainless AlSI 410, sharp Phillips 1131
Thread d ST 4.2
Phillips screw drive 2
Head height k
~
2,6
Head diameter dk 11
Length l (sharp point) 13 - 85
Length l (drill point) 13 - 50
Dimension chart
WRONIC
33
Sheet metal screw
Slotted hex fange head
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 0130 Zinc plated steel, black 0130
Zinc plated steel, white 0130 Zinc plated steel, brown 0130
Thread d ST 3.5 ST (3.9) ST 4.2 ST 4.8 ST 5.5
Width across fats s / Slot width 1/4 1/4 1/4 5/16 5/16
Head height k
~

Head diameter dk
Length l 9.5 13 13 - 50 19 - 50 19 - 50
Dimension chart
34
Hex head screw
Partially threaded
DIN 931
SFS 2063
ISO 4014
EN 24 014
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 8.8 1051 Stainless steel A2 - 70 7053 Acid proof steel A4 - 70 1001
Zinc plated steel 8.8 1053 Hot-dip galvanized steel 5053 Acid proof steel A4 - 80 1001
Nominal diameter d M1.6 M2 M2.5 M3 (M3.5) M4 M5 M6 (M7)

Width across fats s 3.2 4 5 5.5 6 7 8 10 11
Head height k 1.1 1.4 1.7 2 2.4 2.8 3.5 4 4.8
Head width e min. 3.41 4.32 5.45 6.01 6.58 7.66 8.79 11.05 12.12
Length l 12 16 16 20 16 25 20 30 25 35 25 40 25 50 30 60 30 70
Thread length b / l = 12 - 120 9 10 11 12 13 14 16 18 20
Thread length b / l = 130 - 200 22 24 26
Thread length b / l = over 200
Dimension chart
Nominal diameter d M8 M10 M10 M12 M12 (M14) (M14) M16 (M18)
DIN ISO DIN ISO DIN ISO
Width across fats s 13 17 16 19 18 22 21 24 27
Head height k 5.3 6.4 6.4 7.5 7.5 8.8 8.8 10 11.5
Head width e min. 14.38 18.90 17.77 21.1 20.03 24.49 23.36 26.75 30.14
Length l 35 - 80 40 - 100 45 - 100 45 - 120 50 - 120 50 - 140 60 - 140 55 - 160 65 - 180
Thread length b / l = 12 - 120 22 26 26 30 30 34 34 38 42
Thread length b / l = 130 - 200 28 32 36 40 40 44 48
Thread length b / l = over 200 45 49 53 57 61
Nominal diameter d M20 (M22) (M22) M24 (M27) M30 (M33) M36 (M39)
DIN ISO
Head height k 12.5 14 14 15 17 18.7 21 22.5 25
Head width e min. 33.53 35.72 37.72 39.98 45.2 50.85 55.37 60.79 66.44
Length l 65 200 70 220 90 220 80 240 90 260 90 300 100 - 300 110 - 300 120 - 300
Thread length b / l = 12 - 120 46 50 50 54 60 66 72 78 84
Thread length b / l = 130 - 200 52 56 56 60 66 72 78 84 90
Thread length b / l = over 200 65 69 69 73 79 85 91 97 103
35
Hex head screw
Fully threaded
DIN 933
SFS 2064
ISO 4017
EN 24 017
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 8.8 1055 Steel 12.9 2056 Stainless steel A2 - 70 4001
Zinc plated steel 8.8 1057 Brass 4021 Acid proof steel A4 - 70 2001
Hot dipped Zinc plated steel 8.8 5057 Polyamide 2278
Nominal diameter d M1.6 M2 M2.5 M3 (M3.5) M4 M5 M6 (M7) M8

Width across fats s 3.2 4 5 5.5 6 7 8 10 11 13
Head height k 1.1 1.4 1.7 2 2.4 2.8 3.5 4 4.8 5.3
Head width e min. 3.41 4.32 5.45 6.01 6.58 7.66 8.79 11.05 12.12 14.38
Length l 2 - 12 3 - 16 3 - 25 4 - 30 5 - 35 5 - 70 6 - 80 6 - 80 7 - 100 8 - 110
Dimension chart
Nominal diameter d M10 M10 M12 M12 (M14) (M14) M16 M20 (M22) (M22)
DIN ISO DIN ISO DIN ISO DIN ISO
Width across fats s 17 16 19 18 22 21 24 30 32 34
Head height k 6.4 6.4 7.5 7.5 8.8 8.8 10 12.5 14 14
Head width e min. 18.90 17.77 21.1 20.03 24.49 23.36 26.75 33.53 35.72 37.72
Length l 8 - 150 16 - 100 10 - 150 20 - 100 10 - 140 30 - 140 12 - 200 16 - 200 16 - 200 45 - 150
Nominal diameter d M24 (M27) M30 M 30 (M33) M36 (M39)

Width across fats s 36 41 46 46 50 55 60
Head height k 15 17 18.7 18.7 21 22.5 25
Head width e min. 39.98 45.2 50.85 50.85 55.37 60.79 66.44
Length l 16 - 200 22 - 200 35 - 200 35 - 200 35 - 200 35 - 200 35 - 200
36
Socket hex head screw
Socket head cap
DIN 912
SFS 2219
ISO 4762
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 8.8 00840 Steel 12.9 0083 Stainless steel A2 - 80 7084
Zinc plated steel 8.8 0084 Black passivated steel 12.9 00834 Acid proof steel A4 - 80 1007
Nominal diameter d M1.4 M1.6 M2 M2.5 M3 M4 M5 M6 M8 M10 M12 (M14)
Key size s 1.3 1.5 1.5 2 2.5 3 4 5 6 8 10 12
Head height k max. 1.4 1.6 2 2.5 3 4 5 6 8 10 12 14
Head diameter dk max. 1) 2.6 3 3.8 4.5 5.5 7 8.5 10 13 16 18 21
Head diameter dk max. 2) 2.74 3.14 3.98 4.68 5.68 7.22 8.72 10.22 13.27 16.27 18.27 21.33
Length l (full thread) 2 - 12 2.5 - 16 3 - 20 4 - 25 5 - 20 6 - 25 8 - 25 10 - 30 12 - 35 16 - 40 20 - 50 25 - 55
Length l (half thread) 25 - 30 30 - 40 30 - 50 35 - 60 40 - 80 45 - 100 55 - 120 60 - 140
Dimension chart
Nominal diameter d M16 (M18) M20 (M22) M24 (M27) M30 (M33) M36 M42 M48 M56
Key size s 14 14 17 17 19 19 22 24 27 32 36 41
Head height k max. 16 18 20 22 24 27 30 33 36 42 48 56
Head diameter dk max. 1) 24 27 30 33 36 40 45 50 54 63 72 84
Head diameter dk max. 2) 24.33 27.33 30.33 33.39 36.39 40.39 45.39 50.39 54.46 63.46 72.46 84.54
Length l (full thread) 25 - 60 30 - 65 30 - 70 35 - 70 40 - 80 45 - 90 45 - 100 50 - 100 55 - 110 60 - 130 70 - 150 80 - 160
Length l (half thread) 65 - 160 70 - 180 80 - 200 80 - 200 90 - 200 100 - 200 110 - 200 110 - 300 120 - 300 140 - 300 160 - 300 180 - 300
1) Smooth cap
2) Knurled cap
37
Socket head low cap
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 8.8 2086 Black passivated steel 8.8 4086 Acid proof steel A4 - 70 5007
Zinc plated steel 8.8 1086 Stainless steel A2 7086
Nominal diameter d M3 M4 M5 M6 M8 M10 M12 (M 14) M16
Key size s 2 2.5 3 4 5 7 8 10 12
Head height k max. 2 2.8 3.5 4 5 6 7 8 9
Head diameter dk max. 5.5 7 8.5 10 13 16 18 21 24
Length l (full thread) 5 - 18 6 - 20 8 - 25 10 - 25 12 - 30 16 - 35 20 - 45 30 - 50 30 - 55
Length l (half thread) 20 25 30 30 - 40 35 - 60 40 - 70 50 - 80 55 - 80 60 - 80
Dimension chart
DIN 7984
Nominal diameter d (M18) M20 (M22) M24
Key size s 12 14 14 17
Head height k max. 10 11 12 13
Head diameter dk max. 27 30 33 36
Length l (full thread) 40 - 60 40 - 60 50 - 70 50 - 80
Length l (half thread) 70 - 100 70 - 100 80 - 100 90 - 100
38
Socket fat head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 10.9 0089 Dacromet steel 10.9 1089 Stainless steel A2 7089
Zinc plated steel 10.9 00890 Black passivated steel 10.9 3089 Acid proof steel A4 2007
Nominal diameter d M3 M4 M5 M6 M8 M10 M12 (M14)
Key size s 2 2.5 3 4 5 6 8 10
Head height k max. 1.7 2.3 2.8 3.3 4.4 5.5 6.5 7
Head diameter dk max. 6 8 10 12 16 20 24 27
Length l (full thread) 8 - 20 8 - 25 8 - 30 8 - 35 10 - 40 12 - 40 20 - 50 25 - 50
Length l (half thread) 25 - 30 30 - 40 35 - 50 40 - 50 50 - 60 50 - 70 60 - 70 60 - 80
Dimension chart
DIN 7991
Nominal diameter d M16 (M18) M20 (M22) M24
Key size s 10 12 12 14 14
Head height k max. 7.5 8 8.5 13.1 14
Head diameter dk max. 30 33 36 36 39
Length l (full thread) 30 - 60 35 - 60 35 - 70 40 - 80 50 - 90
Length l (half thread) 70 - 90 70 - 100 80 - 100 90 - 100 100
39
Socket head low cap
DIN 6912
Nominal diameter d M4 M5 M6 M8 M10 M12 (M14) M16
Key size s 3 4 5 6 8 10 12 14
Head height k max. 2.8 3.5 4 5 6.5 7.5 8.5 10
Head diameter dk max. 7 8.5 10 13 16 18 21 24
Length l 10 - 50 10 - 60 10 - 70 12 - 80 16 - 90 16 - 100 20 - 120 20 - 140
Dimension chart
Material
Prod.
group
Zinc plated steel 8.8 0086
Nominal diameter d (M18) M20 (M22) M24 (M27) M30 (M33) M36
Key size s 14 17 17 19 19 22 24 27
Head height k max. 11 12 13 14 16 17.5 19.5 21.5
Head diameter dk max. 27 30 33 36 40 45 50 54
Length l 25 - 150 30 - 180 40 - 200 60 - 200 70 - 200 70 - 200 80 - 200 90 - 200
40
Socket dome head
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 10.9 1084 Acid proof steel A4 3007 Stainless steel A2 7084
Steel 1084 Black passivated steel 10.9 10843
ISO 7380
Nominal diameter d M3 M4 M5 M6 M8 M10 M12 M16
Key size s 2 2,5 3 4 5 6 8 10
Head height k max. 1.65 2.20 2.75 3.30 4.40 5.50 6.60 8.80
Length l 6 - 12 8 - 16 10 - 30 10 - 30 10 - 40 16 - 40 16 - 50 20 - 50
Dimension chart
Note: ISO 7380 sets the hardness only as 10.9. However, with this norm the test loads are 80 % of the ISO 898-1 standard.
41
Set screw
Socket set screw with fat point
DIN 913
SFS 4735
ISO 4026
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 45 H 0255 Zinc plated steel 1255 Acid proof steel A4 3016
Nominal diameter d M1.4 M1.6 (M1.8) M2 M2.5 M3 M4 M5 M6
DIN only DIN only
Key size s 0.7 0.7 0.9 0.9 1.3 1.5 2 2.5 3
Diameter dp max. 0.8 0.8 1.0 1.5 2.0 2.5 3.5 4.0
Length l DIN 2.5 - 6 2.5 - 6 2.5 - 6 3 - 10 3 - 10 3 - 20 4 - 20 5 - 25 6 - 35
Length l ISO 2 - 8 2 - 10 2 - 12 2 - 16 2.5 - 20 3 - 25 4 - 30 5 - 40 6 - 50
Dimension chart
Note: 45 H is a property class. (45 H equals HRC 45 min. on the Rockwell scale and HV 450 min. on the
Vickers scale)
Nominal diameter d M8 M10 M12 (M14) M16 (M18) M20 (M22) M24
DIN only DIN only DIN only
Key size s 4 5 6 6 8 10 10 12 12
Diameter dp max. 5.5 7.0 8.5 10.0 12.0 13.0 15.0 17.0 18.0
Length l DIN 8 - 40 10 - 40 16 - 40 20 - 40 20 - 50 25 - 60
Length l ISO 8 - 60 10 - 60 12 - 60 16 - 60
42
Set screw
Socket set screw with cone point
DIN 914
SFS 4736
ISO 4027
Material
Prod.
group
Material
Prod.
group
Steel 45 H 0256 Stainless steel A2 7256
Zinc plated steel 1256 Acid proof steel A4 4016
Nominal diameter d M1.4 M1.6 (M1.8) M2 M2.5 M3 M4 M5 M6 M8
DIN only DIN only
Key size s 0.7 0.7 0.7 0.9 1.3 1.5 2 2.5 3 4
Diameter dp max. - - - - - - - - 1.5 2.0
Length l DIN 2.5 - 6 2.5 - 6 2.5 - 6 3 - 10 4 - 10 4 - 20 5 - 20 6 - 25 8 - 35 10 - 40
Length l ISO 2 - 8 2 - 10 2.5 - 12 2.5 - 16 3 - 20 4 - 25 5 - 30 6 - 40
Dimension chart
Vickers scale)
Nominal diameter d M10 M12 (M14) M16 (M18) M20 (M22) M24
Key size s 5 6 6 8 10 10 12 12
Diameter dp max. 2.5 3.0 4.0 4.0 5.0 5.0 6.0 6.0
Length l DIN 12 - 40 16 - 40 20 - 40 25 - 50 30 - 60
Length l ISO 8 - 50 10 - 60 12 - 60 16 - 60 20 - 60
43
Set screw
Socket set screw with half dog point
DIN 915
SFS 4737
ISO 4028
Material
Prod.
group
Material
Prod.
group
Steel 45 H 0257 Zinc plated steel 1257
Nominal diameter d M1.4 M1.6 (M 1.8) M2 M2.5 M3 M4 M5 M6 M8
DIN only DIN only
Key size s 0.7 0.7 0.7 0.9 1.3 1.5 2 2.5 3 4
Diameter dp max. 0.7 0.8 0.9 1.0 1.5 2.0 2.5 3.5 4.0 5.5
Length l DIN 3 - 6 3 - 6 4 - 6 4 - 10 4 - 10 5 - 20 6 - 20 8 - 25 8 - 35 10 - 40
Length l ISO 2 - 8 2.5 - 10 3 - 12 4 - 16 5 - 20 6 - 25 8 - 30 8 - 40
Dimension chart
Vickers scale)
Key size s 5 6 6 8 10 10 12 12
Diameter dp max. 7.0 8.5 10.0 12.0 13.0 15.0 17.0 18.0
Length l DIN 12 - 40 16 - 40 20 - 40 25 - 50 30 - 60
Length l ISO 10 - 50 12 - 60 16 - 60 20 - 60 25 - 60
44
Set screw
Socket set screw with cup point
DIN 916
SFS 4738
ISO 4029
Material
Prod.
group
Material
Prod.
group
Steel 45 H 0254 Stainless steel A2 7254
Zinc plated steel 1254 Acid proof A4 1016
Vickers scale)
Nominal diameter d M1.4 M1.6 (M 1.8) M2 M2.5 M3 M4 M5 M6 M8
DIN only DIN only
Key size s 0.7 0.7 0.7 0.9 1.3 1.5 2 2.5 3 4
Diameter dp max. 0.7 0.8 0.9 1.0 1.2 1.4 2.0 2.5 3.0 5.0
Length l DIN 2.5 - 6 2.5 - 6 2.5 - 6 3 - 10 3 - 10 4 - 20 5 - 20 5 - 25 6 - 35 8 - 40
Length l ISO 2 - 8 2 - 10 2 - 12 2.5 - 16 3 - 20 4 - 25 5 - 30 6 - 40
Dimension chart
Key size s 5 6 6 8 10 10 12 12
Diameter dp max. 6.0 8.0 9.0 10.0 12.0 14.0 16.0 16.0
Length l DIN 12 - 40 16 - 40 20 - 40 25 - 50 30 - 60
Length l ISO 8 - 50 10 - 60 12 - 60 16 - 60 20 - 60
45
Set screw
Slotted set screw with fat point
DIN 551
ISO 4766
Material
Prod.
group
Polyamide 1278
Nominal diameter d M1 M1.2 M1.4 M1.6 M2 M2.5 M3 (M3.5) M4 M5
ISO only ISO only
Slot width n 0.2 0.2 0.2 0.25 0.25 0.4 0.4 0.5 0.6 0.8
Diameter dp max. 0.5 0.6 0.7 0.8 1.0 1.5 2.0 2.2 2.5 3.5
Length l DIN 2 - 4 2 - 6 3 - 8 3 - 8 3 - 10 3 - 12 4 - 12 4 - 16
Length l ISO 2 - 5 2 - 6 2 - 8 2 - 8 2 - 10 2.5 - 12 3 - 16 4 - 20 4 - 20 5 - 25
Dimension chart
Nominal diameter d M6 M8 M10 M12

Slot width n 1 1,2 1,6 2
Diameter dp max. 4.0 5.5 7.0 8.5
Length l DIN 5 - 20 6 - 25 10 - 30
Length l ISO 6 - 30 8 - 40 10 - 50 12 - 60
46
Wlock
DIN 6921
Material
Prod.
group
Zinc plated steel 8.8 0274
Nominal diameter d M5 M6 M8 M10 M12
Width across fats s 8 10 13 15 17
Head height k 4.3 5.5 7.0 7.9 12.0
Flange diameter d2 11.2 14.5 18.3 21.0 18.0
Length l 10 - 16 10 - 30 16 - 30 20 - 40 20 - 40
Dimension chart
Hexagon fange bolt
Serrated fange
47
Lifting eye bolt
Material
Prod.
group
Material
Prod.
group
Zinc plated type C 15 steel 0295 Acid proof steel A4 2295
DIN 580
Thread diameter d1 M8 M10 M12 M16 M20 M24 M30 M36 M42
Diameter d2 20 25 30 35 40 50 65 75 85
Eye outer diameter d3 36 45 54 63 72 90 108 126 144
Eye inner diameter d4 20 25 30 35 40 50 60 70 80
Eye height h 36 45 53 62 71 90 109 128 147
Thread length l 13 17 20.5 27 30 36 45 54 63
Dimension chart
Lifting eye nut
Material
Prod.
group
Material
Prod.
group
Type C 15 steel 0395 Zinc plated type C 15 steel 0395
DIN 582
Thread diameter d1 M8 M10 M12 M16 M20 M24 M30 M36 M42
Diameter d2 20 25 30 35 40 50 65 75 85
Eye outer diameter d3 36 45 54 63 72 90 108 126 144
Eye inner diameter d4 20 25 30 35 40 50 60 70 80
Height h 36 45 53 62 71 90 109 128 147
Dimension chart
48
Threaded rod
DIN 975
1995 DIN handbook
DIN 976-1 form A
Nominal diameter d M2 M2.5 M3 (M3.5) M4 M5 M6 M8 M10 M12 (M14) M16
Pitch p 0.4 0.45 0.5 0.6 0.7 0.8 1 1.25 1.5 1.75 2 2
Length l 1000 mm 1000 mm and 2000 mm
Dimension chart
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 4.6 0958 Stainless steel A2 7958 Polyamide 3958
Zinc plated steel 8.8 0959 Acid proof steel A4 0953
Nominal diameter d (M18) M20 (M22) M24 (M27) M30 (M33) M36 (M39) M42 (M45) M48
Pitch p 2.5 2.5 2.5 3 3 3.5 3.5 4 4 4.5 4.5 5
Length l 1000 mm and 2000 mm
49
Multipurpose screw (wood screw)
Pan head
Fully threaded
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 0196 Black passivated steel, pozidriv 4196 Stainless steel A2, pozidriv 2182
Torx size
Head height k
~

Head diameter dk max.
Length l 10 - 35 12 - 40 12 - 60 15 - 70 16 - 70 40 - 90
Dimension chart
50
Flat head
Fully threaded
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, pozidriv 0198 Black passivated steel, pozidriv 4198 Stainless steel A2, pozidriv 1182
Thread ST 2.5 ST 3.0 ST 3.5 ST 4.0 ST 4.5 ST 5.0 ST 6.0
Torx size
Head height k
~
1.3 1.7 2.1 2.3 2.5 2.5 3.0
Length l 10 10 - 40 12 - 50 12 - 50 16 - 60 16 - 65 50 - 80
Dimension chart
Flat head
Partially threaded
Torx size
Head height k
~
2.1 2.3 2.5 2.5 3.0
Head diameter dk max. 6.8 7.5 8.1 8.1 9.5
Length l 25 - 40 25 - 60 35 - 80 30 - 120 40 - 180 80 - 140
Dimension chart
Material
Prod.
group
51
Nylon plug
Dimensions d x l 5 x 25 6 x 30 8 x 40 10 x 50 12 x 60 14 x 75
Screw diameter 2.6 - 4 3.5 - 5 4.5 - 6 6 - 8 8 - 10 10 - 12
Drill diameter 5 6 8 10 12 14
Dimension chart
Material
Prod.
group
Nylon 0903
52
Nominal diameter x length M6x40 M6x65 M8x50 M8x75 M8x115 M10x55 M10x80
Thread length 5 10 5 15 55 10 15
Drill diameter 6 6 8 8 8 10 10
Minimum embedment depth 40 60 65 65 65 70 70
Dimension chart
Nominal diameter x length M10x125 M12x70 M12x100 M12x140 M16x115 M16x150
Thread length 45 10 15 50 15 30
Minimum embedment depth 70 90 90 90 110 110
Material
Prod.
group
Wedge anchor
53
Drop-in anchor
Material
Prod.
group
Internal thread M6 M8 M10 M12 M16 M20
Anchor length 28 30 40 50 65 80
Fastened screw length min. 6 8 10 12 16 20
Fastened screw length max. 11 13 15 18 23 34
Dimension chart
PFG-Anchor
Material
Prod.
group
Thread M6 M8 M10 M12
Embedment depth (anchor length) 40 50 60 80
Drill diameter 10 14 16 20
Drill depth 45 55 65 85
Fixture thickness 35 45 35 50
Min. (concrete) thickness
for approval criteria
40 50 60 80
Installation torque 10 25 50 85
Dimension chart
54
Spring pin
DIN 1481
ISO 8752
Material
Prod.
group
Material
Prod.
group
Steel 0475 Stainless steel A2 7475
Nominal diameter d1 1 1.5 2 2.5 3 3.5 4 4.5 5 6
d1 max. before installation 1.3 1.8 2.4 2.9 3.5 4.0 4.6 5.1 5.6 6.7
Thickness s 0.2 0.3 0.4 0.5 0.6 0.75 0.8 1 1 1.2
Chamfer length a max. 0.35 0.45 0.55 0.6 0.7 0.8 0.85 1.0 1.1 1.4
Length l 4 - 20 4 - 20 4 - 30 4 - 30 4 - 40 4 - 40 4 - 50 5 - 50 5 - 80 10 - 100
Shear strength 0.7 1.58 2.82 4.38 6.32 9.06 11.24 15.36 17.54 26.04
Dimension chart
Nominal diameter d1 8 10 12 13 14 16 18 20 21 25
d1 max. before installation 8.8 10.8 12.8 13.8 14.8 16.8 18.9 20.9 21.9 25.9
Thickness s 1.5 2 2.5 2.5 3 3 3.5 4 4 5
Chamfer length a max. 2.0 2.4 2.4 2.4 2.4 2.4 2.4 3.4 3.4 3.4
Length l 10 - 120 10 - 160 10 - 180 10 - 180 10 - 200 10 - 200 10 - 200 10 - 200 14 - 200 14 - 200
Shear strength 42.76 70.16 104.1 115.1 144.7 171 222.5 280.6 298.2 438.5
Nominal diameter d1 28 30 32 35 38 40 45 50
d1 max. before installation 28.9 30.9 32.9 35.9 38.9 40.9 45.9 50.9
Thickness s 5.5 6 6 7 7.5 7.5 8.5 9.5
Chamfer length a max. 3.4 3.4 3.6 3.6 4.6 4.6 4.6 4.6
Length l 14 - 200 14 - 200 20 - 200 20 - 200 20 - 200 20 - 200 20 - 200 20 - 200
Shear strength 542.6 631.4 684 859 1003 1068 1360 1685
Shear strength (ISO 8749 test) kN is the minimum value that covers carbon steel and martensite stainless steel of this norm.
This norm doesnt include austenitic shear strength values, A2 for example.
55
Split cotter pin
DIN 94
SFS 4909
ISO 1234
Nominal diameter 0.6 0.8 1 1.2 1.6 2 2.5 3.2 (3.5) 4
Diameter d1 max. 0.5 0.7 0.9 1 1.4 1.8 2.3 2.9 3.7
Extended prong length a 1.6 1.6 1.6 2.5 2.5 2.5 2.5 3.2 4.0
Eye length b
~
2.0 2.4 3.0 3.0 3.2 4.0 5.0 6.4 8.0
Eye diameter c max. 1.0 1.4 1.8 2.0 2.8 3.6 4.6 5.8 7.4
Length l DIN 6 - 18 8 - 32 10 - 40 12 - 50 18 - 80 40 - 60 20 - 125
Length l ISO 4 - 12 5 - 16 6 - 20 8 - 25 8 - 32 10 - 40 12 - 50 14 - 63 18 - 80
Dimension chart
Nominal diameter 5 6.3 8 10 13 16 20
Diameter d1 max. 4,6 5,9 7,5 9,5 12,4 15,4 19,3
Extended prong length a 4.0 4.0 4.0 6.3 6.3 6.3 6.3
Eye length b
~
10.0 12.6 16.0 20.0 26.0 32.0 40.0
Eye diameter c max. 9.2 11.8 15.0 19.0 24.8 30.8 38.5
Length l DIN 20 - 125 28 - 140 36 - 140 56 - 140 56 - 140 100 - 250
Length l ISO 22 - 100 32 - 125 40 - 160 45 - 200 71 - 250 112 - 280 160 - 280
Standard manufacturing program consists of the preceding lengths, but other lengths can be custom made.
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Steel 1470 Zinc plated steel 0470 Acid proof A4 0474
56
Hex nut
DIN 934
SFS 2067
ISO 4032
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 8 0317 Polyamide 0323 Brass 0300
Hot-dip galvanized steel 8 5317 Stainless steel A2 -70 7317 Nickel plated brass 0307
Black passivated steel 8 3317 Acid proof steel A4 - 70 1008
Nominal diameter d M1 M1.2 M1.4 M1.6 M2 M2.5 M3 (M3.5) M4 M5
Width across fats s 2.5 3 3 3.2 4 5 5.5 6 7 8
Height m max. 0.8 1 1.2 1.3 1.6 2 2.4 2.8 3.2 4
Diameter e min. 2.71 3.28 3.28 3.41 4.32 5.45 6.01 6.58 7.66 8.79
Nominal diameter d M6 (M7) M8 M10 M12 (M14) M16 (M18) M20 (M22)
Height m max. 5 5.5 6.5 8 10 11 13 15 16 18
Diameter e min. 11.05 12.12 14.38 18.90 21.1 24.49 26.75 29.56 32.95 35.03
Nominal diameter d M24 (M27) M30 (M33) M36 (M39)
Width across fats s 36 41 46 50 55 60
Height m max. 19 22 24 26 29 31
Diameter e min. 39.55 45.2 50.85 55.37 60.79 66.44
Width across fats s 3.2 4 5 5.5 6 7 8 10 13 16
Height m max. 1.3 1.6 2 2.4 2.8 3.2 4.7 5.2 6.8 8.4
Diameter e min. 3.41 4.32 5.45 6.01 6.58 7.66 8.79 11.05 14.38 17.77
Nominal diameter d M12 (M14) M16 (M18) M20 (M22) M24 (M27) M30 (M33)
Height m max. 10.8 12.8 14.8 15.8 18 19.4 21.5 23.8 25.6 28.7
Diameter e min. 20.03 23.35 26.75 29.56 32.95 37.29 39.55 45.2 50.85 55.37
Nominal diameter d M36 (M39)
Width across fats s 55 60
Height m max. 31 33,4
Diameter e min. 60.79 66.44
57
Hex jam nut
Fine thread
DIN 936
ISO 4035
4036
8675
Material
Prod.
group
Nominal diameter d M8 M10 M12 (M14) M16 (M18) M20 (M22) M24 (M27)
Pitch p 1 1 1.25 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Pitch p 1.25 1.5 2 2 2 2 2
Height m max. 5 6 7 8 8 9 9 10 10 12
Diameter e min. 14.38 18.90 21.1 24.49 26.75 29.56 32.95 35.03 39.55 45.2
Dimension chart
Nominal diameter d M30 (M33) M36 (M39)
Pitch p 1.5 1.5 1.5 1.5
Pitch p 2 2 2 2
Width across fats s 46 50 55 60
Height m max. 12 14 14 16
Diameter e min. 50.85 55.37 60.79 66.44
58
DIN 439
SFS 2068
ISO 4035
Hex jam nut
Chamfered
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 0318 Stainless steel A2 7318 Acid proof steel A4 5008
Nominal diameter d M1.6 (M1.8) M2 M2.5 M3 M3.5 M4 M5 M6 M8 M10 M12
Pitch p normal 0.35 0.35 0.4 0.45 0.5 0.6 0.7 0.8 1 1.25 1.5 1.75
Pitch p fne 1 1 1 1 1,5
Pitch p fne 2 2 1.25 1.25
Pitch p fne 3
Width across fats s 3.2 3.5 4 5 5.5 6 7 8 10 13 17 19
Height m max. 1 1.1 1.2 1.6 1.8 2 2.2 2.7 3.2 4 5 6
Diameter e min. 3.48 3.82 4.32 5.45 6.01 6.58 7.66 8.79 11.05 14.38 18.90 21.1
Nominal diameter d (M14) M16 (M18) M20 (M22) M24 (M27) M30 (M33) M36 (M39)
Pitch p normal 2 2 2.5 2.5 2.5 3 3 3.5 3.5 4 4
Pitch p fne 1 1.5 1.5 1.5 2 1.5 2 2 2 2 3 3
Pitch p fne 2 2 1.5 2 1.5 2 2
Pitch p fne 3 1.5 1.5 1.5 1.5 1.5
Width across fats s 22 24 27 30 32 36 41 46 50 55 60
Height m max. 7 8 9 10 11 12 13.5 15 16.5 18 19.5
Diameter e min. 24.49 26.75 29.56 32.95 35.03 39.55 45.2 50.85 55.37 60.79 66.44
Please mark your order either as DIN or ISO.
Nominal diameter d M1.6 M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M16 M20
Pitch p normal 0.35 0.4 0.45 0.5 0.7 0.8 1 1.25 1.5 1.75 2 2.5
Width across fats s 3.2 4 5 5.5 7 8 10 13 16 18 24 30
Height m max. 1 1.2 1.6 1.8 2.2 2.7 3.2 4 5 6 8 10
Diameter e min. 3.41 4.32 5.45 6.01 7.66 8.79 11.05 14.38 14.38 20.03 26.75 32.95
Nominal diameter d M24 M30 M36
Pitch p normal 3 3.5 4
Width across fats s 36 46 55
Height m max. 12 15 18
Diameter e min. 39.55 50.85 60.79
59
DIN 985
ISO 7040
Nyloc lock nut
Nylon insert
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 8 0368 Stainless steel A2 7368 Acid proof steel A4 1011
Nominal diameter d M3 M4 M5 M6 (M7) M8 M10 M12 (M14) M16
Pitch p normal 0.5 0.7 0.8 1 1 1.25 1.5 1.75 2 2
Pitch p fne 1 1 1 1.5 1.5 1.5
Pitch p fne 2 1.25 1.25
Width across fats s 5.5 7 8 10 11 13 17 19 22 24
Height m max. 4 5 5 6 7.5 8 10 12 14 16
Diameter e min. 6.01 7.66 8.79 11.05 14.38 14.38 18.90 21.1 24.49 26.75
Nominal diameter d (M18) M20 (M22) M24 (M27) M30 (M33) M36 (M39)
Pitch p normal 2.5 2.5 2.5 3 3 3.5 3.5 4 4
Pitch p fne 1 2 2 2 2 2 2 2 3 3
Pitch p fne 2 1.5 1.5 1.5
Height m max. 18.5 20 22 24 27 30 33 36 39
Diameter e min. 29.56 32.95 35.03 39.55 45.2 50.85 55.37 60.79 66.44
Nominal diameter d M3 M4 M5 M6 M8 M10 M12 (M14) M16 M20
Pitch p normal 0.5 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5
Height m max. 4.50 6.00 6.80 8.00 9.50 11.90 14.90 17.00 19.10 22.80
Diameter e min. 6.01 7.66 8.79 11.05 14.38 17.77 20.03 23.36 26.75 32.95
Nominal diameter d M24 M30 M36
Pitch p normal 3 3.5 4
Width across fats s 36 46 55
Height m max. 12 15 18
Diameter e min. 39.55 50.85 60.79
60
DIN 980 V
Material
Prod.
group
Zinc plated steel 8 0368
Pitch p normal 1 1 1.5 1.5 1.5
Pitch p fne 1 1.25 1.25
Pitch p fne 2 0.5 0.7 0.8 1 1 1.25 1.5 1.75 2 2
Height m max. 3.7 4.2 5.1 6 7 8 10 12 14 16
Diameter e min. 6.01 7.66 8.79 11.05 12.12 14.38 18.90 21.1 24.49 26.75
Dimension chart DIN 980 V
Nominal diameter d (M18) M20 (M22) M24 (M27) M30 (M33) M36 (M39)
Pitch p normal 2 2 2 2 2 2 2 3 3
Pitch p fne 1 1.5 1.5 1.5
Pitch p fne 2 2.5 2.5 2.5 3 3 3.5 3.5 4 4
Height m max. 18 20 22 24 27 30 33 36 39
Diameter e min. 29.56 32.95 35.03 39.55 45.2 50.85 55.37 60.79 66.44
Lock nut
All metal form V
Fine thread
61
Material
Prod.
group
Zinc plated steel 8 0394
Nominal diameter d M5 M6 M8 M10 M12 M16
Height k max. 5 6 8 10 13 16
Flange diameter d2 11.8 14.2 17.9 21.8 26.0 34.5
Dimension chart
Wlock nut
Serrated fange
62
Cap nut
DIN 1587
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 6 0356 Stainless steel A2 7356 Brass 1352
Polyamide 2352 Acid proof A4 4008 Nickeled brass 0352
Nominal diameter d M3 M4 M5 M6 M8 M10 M10 M12 M12 (M14) (M 14)
DIN ISO DIN ISO ISO
Pitch p normal 0.5 0.7 0.8 1 1.25 1.5 1.75 1.75 1.75 2 2
Pitch p fne 1 1 1 1 1.5 1.5 1.5 1.5 1.5
Pitch p fne 2 1.25 1.25 1.25
Width across fats s 5.5 7 8 10 13 16 17 18 19 21 22
Height m max. 6 8 10 12 15 18 18 22 22 25 25
Diameter e min. 6.01 7.66 8.79 11.05 14.38 17.77 18.90 20.03 21.1 23.35 24.49
Dimension chart
Nominal diameter d (M14) M16 (M18) M20 (M22) (M22) M24
DIN ISO DIN ISO
Pitch p normal 2 2 2.5 2.5 2.5 2.5 3
Pitch p fne 1 1.5 1.5 1.5 2 1.5 1.5 2
Pitch p fne 2 1.25 2 1.5 2 2
Height m max. 25 28 32 34 39 39 42
Diameter e min. 24.49 26.75 30.14 33.53 37.72 35.72 39.98
63
Cage nut
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Cage: zinc plated spring steel
Nut: zinc plated steel
0381
Cage: stainless steel A2
Nut: stainless steel A2
1381
Cage: stainless steel A2
Nut: zinc plated steel
Nominal diameter
d
Sheet thickness
P
Square hole
size
Dimensions
A B C D E F G
M3, M4 and M5 0.7 1.6 6.7 x 6.7 10.5 10.0 7.2 6.5 0.45 10.3 5.0
M4
0.7 1.6
8.3 x 8.3 12.0 11.5
8.0
7.2 0.45 12.2 6.0
1.7 2.5 9.0
2.6 3.5 10.0
3.6 4.5 11.0
M5
0.7 1.6
8.3 x 8.3 12.0 11.5
8.0
7.2 0.45 12.2 6.0
1.7 2.5 9.0
2.6 3.5 10.0
3.6 4.5 11.0
M6
0.7 1.6
8.3 x 8.3 12.0 11.5
8.0
7.2 0.45 12.2 6.0
1.7 2.5 9.0
2.6 3.5 10.0
3.6 4.5 11.0
M4
0.7 1.6
9.5 x 9.5 13.5 12.7
8.7
8.2 0.50 13.5 7.2 1.7 2.6 9.7
2.7 3.5 10.2
M5
0.7 1.6
9.5 x 9.5 13.5 12.7
8.7
8.2 0.50 13.5 7.2 1.7 2.6 9.7
2.7 3.5 10.2
M6
0.7 1.6
9.5 x 9.5 13.5 12.7
8.7
8.2 0.50 13.5 7.2 1.7 2.6 9.7
2.7 3.5 10.2
M6 1.2 2.2 10.0 x 10.0 15.0 11.3 9.7 9.5 0.50 15.0 6.0
M6
0.7 1.6
12.3 x 12.3 16.5 16.0
10.4
10.6 0.55 16.6 7.8 1.7 2.6 11.5
2.7 3.5 13.0
M8
0.7 1.6
12.3 x 12.3 16.5 16.0
10.4
10.6 0.55 16.6 7.8 1.7 3.0 11.5
3.1 4.0 13.0
M10
0.7 1.6
12.3 x 12.3 16.5 16.0
10.4
10.6 0.55 16.6 7.8 1.7 3.0 11.5
3.1 4.0 13.0
Dimension chart
64
DIN 562
Square nut
Thin square nut
Material
Prod.
group
Dimension chart
ISO = Width across fats according to ISO.
Please mark your order as with DIN or ISO.
Nominal diameter d M1.6 M2 M2.5 M3 (M3.5) M4 M5 M6 M8 M10 M10
Pitch p 0.35 0.4 0.45 0.5 0.6 0.7 0.8 1 1.25 1.5 1.5
Width across fats s 3.2 4 5 5.5 6 7 8 10 13 17 16
Height m max. 1 1.2 1.6 1.8 2 2.2 2.7 3.2 4 5 5
Diameter e min. 4 5 6.3 7 7.6 8.9 10.2 12.7 16.5 21.50 20.20
ISO
65
Material
Prod.
group
Nominal diameter d M5 M6 M8 M10 M12 M16 M20
Pitch p 0.8 1 1.25 1.5 1.75 2 2.5
Height m 15 25 25 30 40 40 60
Dimension chart
Extension nut
DIN 6330
Dimension chart according to DIN (6334)
Material
Prod.
group
Nominal diameter d M6 M8 M10 M12 M16 M20
Pitch p 1 1.25 1.5 1.75 2 2.5
Height m 18 24 30 36 48 58
Dimension chart
DIN (6334)
66
Material
Prod.
group
Material
Prod.
group
Nominal diameter d M4 M5 M6 M8 M10 M12 M16 M20 M24
Diameter d2 max. 8 11 13 16 20 23 29 35 44
Width e max. 20 26 33 39 51 65 73 90 110
Height h max. 10.5 13 17 20 25 33.5 37.5 46.5 56.5
Height m max. 4.6 6.5 8 10 12 14 17 21 25
Dimension chart
DIN 315
Wing nut
67
Height d1 8 12 9 12 16
Diameter b 15 17 19 22 25
Claw a 5.5 5.5 7.0 7.5 11.0
Dimension chart
DIN 1624
T-nut (4 - claw nut)
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 0376 Steel 9376
M6, M8 and M10 only available as non-surface fnished steel.
68
Plain washer
DIN 125 A
SFS 2041
ISO 7089
Material
Prod.
group
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 140 HV 0407 Stainless steel A2 140 HV 7407 Brass 0400
Black passivated steel 140 HV 2407 Acid proof steel A4 140 HV 1009 Polyamide 0421
Hot-dip galvanized steel 140 HV 5407
Nominal diameter d 1.6 1.7 2 2.3 2.5 2.6 3 3.5 4 5 6
Internal diameter d1 min. 1.7 1.8 2.2 2.5 2.7 2.8 3.2 3.7 4.3 5.3 6.4
External diameter d2 max. 4 4.5 5 6 6 7 7 8 9 10 12
Thickness h 0.3 0.3 0.3 0.5 0.5 0.5 0.5 0.5 0.8 1 1.6
Dimension chart
Nominal diameter d 7 8 10 12 14 16 18 20 22 24 26
Internal diameter d1 min. 7.4 8.4 10.5 13 15 17 19 21 23 25 27
External diameter d2 max. 14 16 20 24 28 30 34 37 39 44 50
Thickness h 1.6 1.6 2 2.5 2.5 3 3 3 3 4 4
Nominal diameter d 27 28 30 32 33 35 36 38 39
Internal diameter d1 min. 28 29 31 33 34 36 37 39 40
External diameter d2 max. 50 50 56 60 60 66 66 72 72
Thickness h 4 4 4 5 5 5 5 6 6
69
Fender washer
DIN 9021
ISO 7093
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 0416 Stainless steel A2 7411
Polyamide 2416 Acid proof steel A4 1015
Nominal diameter d 2.5 3 3.5 4 5 6 7 8 10 12
DIN only DIN only
Internal diameter d1 min. 2.7 3.2 3.7 4.3 5.3 6.4 7.4 8.4 10.5 13
External diameter d2 max. 8 9 11 12 15 18 22 24 30 37
Thickness h 0.9 0.9 0.9 1.1 1.4 1.8 2.2 2.2 2.7 3.3
Dimension chart
Nominal diameter d 14 16 18 20 24 30 36
DIN only
Internal diameter d1 min. 15 17 20 22 26 33 39
External diameter d2 max. 44 50 56 60 72 92 110
Thickness h 3.3 3.3 4.6 4.6 6 7 9.2
70
Spring washer
DIN 127
Material
Prod.
group
Material
Prod.
group
Black passivated steel 2441 Acid proof steel A4 1010
Nominal diameter d 2 2.2 2.5 3 3.5 4 5 6 7 8 10
External diameter d2 max. 4.4 4.8 5.1 6.2 6.7 7.6 9.2 11.8 12.8 14.8 18.1
Model A thickness h max. 2.1 2.2 2.5 3.2 4.2 4.2 5.4 5.9
Model B thickness h max. 1.2 1.4 1.4 1.9 1.9 2.1 2.8 3.8 3.8 4.7 5.2
Dimension chart
Nominal diameter d 12 14 16 18 20 22 24 27 30 36 39
External diameter d2 max. 21.1 24.1 27.4 29.4 33.6 35.9 40 43 48.2 58.2 61.2
Model A thickness h max. 6.8 8 9.2 9.2 10.4 10.4 13 13 16.1 16.1 16.1
Model B thickness h max. 5.9 7.1 8.3 8.3 9.4 9.4 11.8 11.8 14.2 14.2 14.2
Spring washer
For socket hex screws
DIN 7980
Material
Prod.
group
Nominal diameter d 3 3.5 4 5 6 8 10 12 14 16 18
External diameter d2 max. 5.6 6.1 7 8.8 9.9 12.7 16 18 21.1 24.4 26.4
Thickness s 1 1 1.2 1.6 1.6 2 2.5 2.5 3 3.5 3.5
Thickness h max. 2.36 2.36 2.83 3.78 3.78 4.72 5.9 5.9 7.1 8.25 8.25
Dimension chart
Internal diameter d1 min. 20.2 22.5 24.5 27.5 30.5 33.5 36.5 42.5 49
External diameter d2 max. 30.6 32.9 35.9 38.9 44.1 47.1 52.2 60.2 67
Thickness s 4.5 4.5 5 5 6 6 7 8 8
Thickness h max. 10.6 10.6 11.8 11.8 14.2 14.2 16.5 18.9 18.9
71
Wave washer
DIN 137
Model A Model B
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, model A 0434 Stainless steel A2, model A 7434
Zinc plated steel, model B 0435 Stainless steel A2, model B 3435
Nominal diameter d 1 1.2 1.4 1.7 1.8 2 2.3 2.6 3 3.5
Internal diameter d1 min. 1.1 1.3 1.5 1.8 1.9 2.2 2.5 2.8 3.2 3.7
External diameter d2 2.5 3 3 4 4 4.5 5 5.5 6 7
Thickness h max. 0.7 0.7 0.8 0.9 0.9 1 1 1.1 1.3 1.4
Dimension chart (Model A)
Nominal diameter d 4 5 6 7 8 10
Internal diameter d1 min. 4.3 5.3 6.4 7.4 8.4 10.5
External diameter d2 8 10 11 12 15 18
Thickness h max. 1.6 1.8 2.2 2.4 3.4 4
Nominal diameter d 3 3.5 4 5 6 7 8 10 12 14
Internal diameter d1 min. 3.2 3.7 4.3 5.3 6.4 7.4 8.4 10.5 13 15
External diameter d2 8 8 9 11 12 14 15 21 24 28
Thickness h max. 1.6 1.8 2 2.2 2.6 3 3 4.2 5 6
Dimension chart (Model B)
Nominal diameter d 16 18 20 22 24 27 30 33 36 39
Internal diameter d1 min. 17 19 21 23 25 28 31 34 37 40
External diameter d2 30 34 36 40 44 50 56 60 68 72
Thickness h max. 6.4 6.6 7.4 7.8 8.2 9.4 10 10.6 11.6 12.8
72
Star washer
DIN 6797
Model A
Model J
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, model A 0423 Stainless steel A, model J 0423
Nominal diameter d 1.6 2 2.5 3 3.5 4 5 6 7 8 10 12
Internal diameter d1 min. 1.7 2.2 2.7 3.2 3.7 4.3 5.3 6.4 7.4 8.4 10,5 13
External diameter d2 max. 3.6 4.5 5.5 6 7 8 10 11 12.5 15 18 20,5
Thickness s1 0.3 0.3 0.4 0.4 0.5 0.5 0.6 0.7 0.8 0.8 0,9 1
Dimension chart
Nominal diameter d 10 12 10 12 14 16 18 20 22 24 27 30
Internal diameter d1 min. 10,5 13 10.5 13 15 17 19 21 23 25 28 31
External diameter d2 max. 18 20,5 18 20.5 24 26 30 33 36 38 44 48
Thickness s1 0,9 1 0.9 1 1 1.2 1.4 1.4 1.5 1.5 1.6 1.6
Thickness h 2 x s1
73
Star washer
DIN 6798
Model A
Model J
Nominal diameter d 1.6 2 2.5 3 3.5 4 5 6 7 8
Internal diameter d1 min. 1.7 2.2 2.7 3.2 3.7 4.3 5.3 6.4 7.4 8.4
External diameter d2 max. 3.6 4.5 5.5 6 7 8 10 11 12.5 15
Thickness s1 0.3 0.3 0.4 0.4 0.5 0.5 0.6 0.7 0.8 0.8
Dimension chart
Nominal diameter d 10 12 14 16 18 20 22 24 27 30
Internal diameter d1 min. 10.5 13 15 17 19 21 23 25 28 31
External diameter d2 max. 18 20.5 24 26 30 33 36 38 44 48
Thickness s1 0.9 1 1 1.2 1.4 1.4 1.5 1.5 1.6 1.6
Thickness h 3 x s1
Material
Prod.
group
Material
Prod.
group
Zinc plated steel, model A 0429 Black passivated steel, Model A 2429
Zinc plated steel, model J 0428 Stainless steel A2, model A 7429
74
Washer
Double serrated lock washer DD
Material
Prod.
group
Dimension chart
Nominal diameter 3 4 4 5 5 6 6 6 7
Internal diameter d 3.05 4.2 4.2 5.1 5.6 6.1 6.5 6.5 7.1
External diameter D 12.4 15.6 17.9 17.9 17.9 18.2 19.7 22.25 20.0
Thickness e 0.5 0.8 0.8 0.8 0.8 0.9 0.9 1.0 1.0
Nominal diameter 8 8 9 10 12 12 14 16
Internal diameter d 8.2 8.2 9.7 10.2 12.3 13.0 14.5 16.3
External diameter D 22.25 27.5 25.4 26.1 30.3 32.7 33.7 36.1
Thickness e 1.0 1.1 1.0 1.1 1.2 1.4 1.4 1.4
75
Material
Prod.
group
Material
Prod.
group
Nominal diameter 4 5 6 8 10 12 16
Internal diameter d1 4.3 5.3 6.4 8.4 10.5 13 17
External diameter d2 10 12 15 20 25 32 42
Thickness s 1.0 1.5 1.5 2.5 2.5 3.0 4.0
Levelness z 0.10 0.15 0.15 0.20 0.20 0.25 0.25
Dimension chart
SFS 3738
Washer
Plain washer for aluminium joints (Sesko-washer)
76
Conical spring washer
DIN 6796
Material
Prod.
group
Material
Prod.
group
Nominal diameter d 2 2.5 3 3.5 4 5 6 7 8 10
Internal diameter d1 H14 2.2 2.7 3.2 3.7 4.3 5.3 6.4 7.4 8.4 10.5
External diameter d2 H14 5 6 7 8 9 11 14 17 18 23
Thickness h max. 0.6 0.72 0.85 1.06 1.3 1.55 2 2.3 2.6 3.2
Dimension chart
Internal diameter d1 H14 13 15 17 19 21 23 25 28 31
External diameter d2 H14 29 35 39 42 45 49 56 60 70
Thickness h max 3.95 4.65 5.25 5.8 6.4 7.05 7.75 8.35 9.2
77
Screw diameter 2.0 2.5 2.8 3.0 3.5 3.8 4.0 4.5 4.5 5.0 5.5 6.0
Internal diameter d1 min. 3.5 4 5 5.5 6 7
External diameter d2 max. 8 9 11 13 14 16
Dimension chart
Cup washer
Bonding sealing gasket
Material
Prod.
group
Material
Prod.
group
Aluminium + EPDM rubber 2444 Stainless steel A2 + EPDM rubber 3444
Screw diameter 4.8 6.3 6.3
Internal diameter d1 (metal) 5.5 7 7
Internal diameter d2 (EPDM rubber) 3.8 5.1 5.1
External diameter D max. 14 16 19
Metal thickness s1 1 1 1
Rubber thickness s2 2 2 2
Dimension chart
Material
Prod.
group
Material
Prod.
group
Nickel plated brass 2444 Aluminium 3444
78
Washer
Wrth-lock (Locking element)
Type NL3 NL4 NL5 NL6 NL6sp NL8 NL8sp NL10 NL10sp NL11
Internal diameter d 3.2 4.3 5.2 6.5 6.5 8.2 8.2 10.3 10.3 11.4
External diameter D 7.0 9.0 9.0 10.8 13.5 13.5 16.6 16.6 21.0 18.5
Thickness T 1.8 1.8 1.8 1.8 2.5 2.5 2.5 2.5 2.5 2.5
MvNm 1.5 3.5 7.2 12 13 30 32 59 64 84
Dimension chart
Material
Prod.
group
Material
Prod.
group
Zinc plated steel 0427 Acid proof A4 1427
Surface hardness HRA 75 +/- 3 % (HRC 48)
MvNm = Tightening torque for 8.8 screws
NL8sp - NL1 is available also as pre-assembled pairs (glued together).
Type NL12 NL12sp NL14 NL16 NL16sp NL18 NL20 NL22 NL24 NL1
Thickness 2.5 3.4 3.4 3.4 3.4 3.4 3.4 3.4 3.4 3.4
MvNm 103 110 160 250 260 350 490 660 850 850
Type NL33 NL36 NL39 NL42 NL27 NL30
Internal diameter d 33.5 36.6 39.5 42.5 28.5 30.5
External diameter D 48.5 58.5 58.5 58.5 42.0 47.0
Thickness 4.6 4.6 4.6 4.6 4.6 4.6
MvNm 2200 2900 3800 3900 1220 1660
79
Type NL3 NL4 NL5 NL6 NL6sp NL8 NL8sp NL10 NL10sp NL11
Thickness T 1.8 1.8 1.8 1.8 2.5 2.5 2.5 2.5 2.5 2.5
MvNm 1.5 3.5 7.2 12 13 30 32 59 64 84
Type NL33 NL36 NL39 NL42 NL27 NL30
Internal diameter d 33.5 36.6 39.5 42.5 28.5 30.5
External diameter D 48.5 58.5 58.5 58.5 42.0 47.0
Thickness 4.6 4.6 4.6 4.6 4.6 4.6
MvNm 2200 2900 3800 3900 1220 1660
Circlip
Standard external circlip
for axles and shafts
DIN 471-1
Material
Prod.
group
Material
Prod.
group
Axle diameter d1 3 4 5 6 7 8 9 10 11 12
Thickness s 0.4 0.4 0.6 0.7 0.8 0.8 1.0 1.0 1.0 1.0
Dimension chart
Axle diameter d1 13 14 15 16 17 18 19 20 21 22
Thickness s 1.0 1.0 1.0 1.0 1.0 1.2 1.2 1.2 1.2 1.2
Axle diameter d1 24 25 26 28 29 30 32 34 35 36
Thickness s 1.2 1.2 1.2 1.5 1.5 1.5 1.5 1.5 1.5 1.75
Axle diameter d1 38 40 42 45 48 50 52 55 56 58
Thickness s 1.75 1.75 1.75 1.75 1.75 2.0 2.0 2.0 2.0 2.0
Axle diameter d1 60 62 63 65 68 70 72 75 78 80
Thickness s 2.0 2.0 2.0 2.5 2.5 2.5 2.5 2.5 2.5 2.5
Spring steel HRC 47 - 52 or HV 480 - 558 kp/mm
2
if axle diameter is 38 mm or less.
2
if axle diameter is 40 mm to 200 mm.
2
if axle diameter is 210 mm or more.
Axle diameter d1 82 85 88 90 95 100 105 110 115 120
Thickness s 2.5 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0
80
Circlip
Standard internal circlip
for holes
DIN 472-1
Material
Prod.
group
Steel 0439
Bore diameter d1 8 9 10 11 12 13 14 15 16 17
Thickness s 0.8 0.8 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
Dimension chart
Bore diameter d1 18 19 20 21 22 24 25 26 28 30
Thickness s 1.0 1.0 1.0 1.0 1.0 1.2 1.2 1.2 1.2 1.2
Bore diameter d1 31 32 34 35 36 37 38 40 42 45
Thickness s 1.2 1.2 1.5 1.5 1.5 1.5 1.5 1.75 1.75 1.75
Bore diameter d1 47 48 50 52 55 56 58 60 62 63
Thickness s 1.75 1.75 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
Bore diameter d1 65 68 70 72 75 78 80 82 85 88
Thickness s 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 3.0 3.0
2
if axle diameter is 38 mm or less.
2
if axle diameter is 40 mm to 200 mm.
2
if axle diameter is 210 mm or more.
Bore diameter d1 90 92 95 98 100 102 105 108 110 112
Thickness s 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0
81
Circlip
Standard E type circlip
for axles and shafts
DIN 6799
Axle diameter d1 1 - 1.4 1.4 - 2 2 - 2.5 2.5 - 3 3 - 4 4 - 5 5 - 7 6 - 8 7 - 9
Free diameter d2 0.8 1.2 1.5 1.9 2.3 3.2 4 5 6
Nominal shaft / axle diameter d3 2.25 3.25 4.25 4.8 6.3 7.3 9.3 11.3 12.3
Thickness s 0.2 0.3 0.4 0.5 0.6 0.6 0.7 0.7 0.7
Gap width a 0.58 1.01 1.28 1.61 1.94 2.70 3.34 4.11 5.26
Dimension chart
Material
Prod.
group
Material
Prod.
group
Spring steel C60, C 67 or C 75, according to DIN 17222
Hardness 460 - 580 HV (46-54 HRC on Rockwell scale)
Axle diameter d1 8 - 11 9 - 12 10 - 14 11 - 15 13 - 18 16 - 24 20 - 31 25 - 38 32 - 42
Free diameter d2 7 8 9 10 12 15 19 24 30
Nominal shaft / axle diameter d3 14.3 16.3 18.8 20.4 23.4 29.4 37.6 44.6 52.6
Thickness s 0.9 1.0 1.1 1.2 1.3 1.5 1.75 2.0 2.5
Gap width a 5.84 6.52 7.63 8.32 10.45 12.61 15.92 21.88 25.80
82
Press-in fasteners can be used to create, either internal or
external threaded joints on sheet metal. These joining ele-
ments are securely clinched to the host material.
The joints can be used to attach and detach objects several
times with a screw or a nut. This feature allows the improve-
ment of manufacturing efciency and the production of com-
plex sheet metal solutions, such as closed corner products.
There are two types of press-in fasteners, SELF-BROACHING
and SELF-CLINCHING based fasteners. Both types are in-
stalled to a drilled or punched mount hole in the host mate-
rial, by applying a constant squeezing force.
Fasteners for sheet metal
83
Self-broaching fasteners
A fastener is attached to a mount hole and is pressed from the opposite side, so that the bottom face of the fastener
clinches to the host material. The serrated clinching ring in the shank of the fastener provides torque resistance, which
prevents any turning between the host material and the fastener. This type of fastener suits well for thin and hard
materials.
Self-clinching fasteners
Fasteners with a hexagon head or serrated clinching ring are attached to the host material in a mount hole. The bot-
tom face of the fastener is designed to displace the host material causing it to fow into the thread or groove of the
fastener, thus locking the fastener securely to the host material. This type of fastener suits especially for sheet metals of
medium hardness with minimum thickness of 0.8 mm, as well as for softer materials.
More specifed information about the properties and benefts of an individual fastener can be found
from the product page.
84
20 - 70RB
70 - 80RB
>80RB
0.5 - 0.8
0.8 - 1.0
1.0 - 1.5
1.5 - 3.0
3.0 - 4.0
4.0 - 6.0
>6.0
S
h
e
e
t

h
a
r
d
n
e
s
s
S
h
e
e
t

t
h
i
c
k
n
e
s
s
WEARB
WEARBSO
WEMINARB
WEMINOFF
WES WECLS WEF WEFH WEFHS WEHFH WESO WEBSO WEMINLOK
Brass
Aluminium
Steel
Stainless steel
S
h
e
e
t

m
a
t
e
r
i
a
l
WEARB
WEARBSO
WEMINARB
WEMINOFF
Steel
Non-alloyed carbon steel
Quenched carbon steel
Stainless steel
F
a
s
t
e
n
e
r

m
a
t
e
r
i
a
l
WEARB
WEARBSO
WEMINARB
WEMINOFF
Push-out force
Pull-through force N/A N/A N/A N/A N/A
Fastener moment
Max. torque
Pull-through moment N/A N/A N/A N/A N/A
Thru-holed YES YES YES YES YES N/A N/A N/A YES NO YES
Blind NO NO NO NO NO N/A N/A N/A NO YES NO
Flush groove NO NO YES YES YES YES YES YES YES YES NO
Locking NO NO NO NO NO NO NO NO NO NO YES
WEARB
WEARBSO
WEMINARB
WEMINOFF
P
r
o
p
e
r
t
i
e
s
Hand tool
Manual clamp
Slow constant clamp
Full automatic
I
n
s
t
a
l
l
a
t
i
o
n
WEARB
WEARBSO
WEMINARB
WEMINOFF
Recommended
Possible
Contact WE sales for more info
Not recommended
High
Adequate
Not possible N/A
85
WEARB and WEARBSO
WEARB and WEARBSO are internal threaded self-broaching nuts with a serrated shank. When installed the
shank rivets around the hole, while the serrated part clinches itself frmly to the host material, ensuring a strong
and enduring joint.
WEMINARB
WEAMINARB is a miniaturized WEARB. It is especially designed for spots with limited space to operate.
WEMINLOK
WEMINKLOK includes the properties of WEMINARB. The last few leads of the nut are distorted in order to give
the nut the ability to lock attached fastener, making it resistive to working and vibration loosening.
WES and WECLS
WES and WECLS are self-clinching fush nuts, which are installed into a mount hole and locks in place by
shaping the host material causing the displaced material to fow to the serrated ring at the bottom face of the
fastener.
WEFH and WEFHS
WEFH and WEFHS are self-clinching studs that are installed into a mount hole and lock in place by shaping the
host material causing the displaced material to fow smoothly and evenly into the groove and around the ribs.
WEHFH
WEHFH is a self-clinching stud, which is installed into a mount hole and lock in place by shaping the host mate-
rial causing the displaced material to fow smoothly and evenly into the groove and around the ribs.
WEF
WEF is a self-clinching fush nut, which allows level surface on both sides of the host material. When installed
the hexagonal head embeds into the base material causing the displaced material to fow into the groove, thus
locking the fastener to the host material.
WEBSO and WESO
WEBSO and WESO are self-clinching standofs, which allows fastening in diferent distances from the host mate-
rial. When installed, the hexagonal head embeds into the host material causing the displaced material to fow
into the clinching groove.
86
Self-broaching nut
Benefts
Suits well for thin and strong materials
Suits well for aluminium, light metals, magnesium etc.
Can be installed using manual or automatic tools
Suits well for both drilled and punched mount holes
Suits well for materials with thickness 6 mm or less
Suits well for the attachment of two sheets
WEARB and WEARBSO are internal threaded self-broaching nuts
with serrated shank.
When installed, the bottom face of the nut mounts around the
hole, while the serrated shank clinches frmly to the host mate-
rial, ensuring a strong and enduring joint.

Mount hole diameter in sheet metal
The mount hole can be made by drilling or punching.
Hole tolerance should be --0.00 + 0.1 mm.
Installation
To achieve the best installation result, it is important to use a properly
manufactured riveting tool (see page 92). It is recommended to use
a clamp to achieve a constant result. Small amounts can also be
installed by hand tools
Nut types
If there are room for the serrated ribs in the mount hole, using a size
bigger nut is recommended.
Usage
In order to achieve the best possible joint, it is recommended to install
the screw through the opposite side of the head, although it is possible
to install the screw from the top face side.
Installation and design instructions
87
Technical info: WEARB, WEARBSO
Nut Extension nut
WEARB WEARBSO
Thread
Shank
diameter A
mm
Head diam-
eter B mm
Head
height C
mm
Thread
length D
mm
WEARBSO
Recommended
hole diameter
-0.00 + 0.10 mm
M2.5, 3 5.8 7.9 3.2 3.3 5.90
M3.5 6.9 9.5 3.8 3.9 6.95
M4 6.9 9.5 3.8 3.9 6.95
M5 8.3 11.1 4.4 4.6 8.35
M6 9.5 12.7 5.7 5.9 9.65
M8 13.0 15.9 6.4 6.5 13.10
M10 15.4 19.1 7.6 7.9 15.50
M12 19.4 25.4 10.2 10.4 19.50
Material:
Steel, zinc plated
Millimeters 3 4 5 6 8 10 12 14 16 18 20 25
Shank 001 003 004 006 008 010 012 013 014 016
Sheet thickness 0.5 - 0.6 0.7 - 0.8 0.9 - 1.0 1.1 - 1.3 1.4 - 1.6 1.7 - 1.9 2.0 - 2.2 2.3 - 2.5 2.6 - 2.8 2.9 - 3.1
Shank 017 018 019 020 022 023 024 026
Sheet thickness 10 swg 3.2 - 3.4 3.5 - 3.7 3.8 - 4.0 4.1 - 4.3 4.4 - 4.6 4.7 - 4.9 5.0 - 5.9
Ordering instructions
WEARBSO
Product name WEARBSO-M4-008-12MM-Z
Thread WEARBSO-M4-008-12MM-Z
Shank WEARBSO-M4-008-12MM-Z
Length WEARBSO-M4-008-12MM-Z
WEARB
Product name WEARB-M4-008
Thread WEARB-M4-008
Shank WEARB-M4-008
Dimension chart
WEARBSO - lengths
88
Miniature self-broaching nut
WEMINARB and WEMINOFF are miniaturized internal threaded
self-broaching nuts with serrated shank.
rial, ensuring a strong and enduring joint. This product is espe-
cially designed for places with limited space to operate.
Benefts
Suits well for thin and strong materials
Suits well for light metals such as aluminium, magnesium, etc.
Suitable for materials with thickness between 0.5 - 3.0 mm
Can be installed to a place with limited space or near the edge
of the sheet.

The mount hole can be made either by drilling or punching.
Installation
To achieve the best installation result, it is important to use a proper
riveting tool (see page 92). It is recommended to use a clamp to
achieve a constant result. Small amounts can also be installed by
hand tools.
Nut types
Usage
In order to achieve the best possible joining element, it is recommend-
ed to install the screw through the opposite side of the head, although
it is possible to attach the screw from the top face side.
89
Technical info: WEMINARB, WEMINOFF
Nut Extension nut
WEMINARB WEMINOFF
Thread
Shank
diameter A
mm
Head
diameter B
mm
Head
height
mm
Thread
length D
mm
WEMINOFF
Recommended
hole diameter
-0.00 + 0.10 mm
M2 3.5 5.0 2.3 2.8 3.6
M2.5 4.2 5.5 2.8 3.3 4.3
M3 4.2 5.5 2.8 3.3 4.3
M3.5 5.4 7.0 3.2 3.8 5.5
M4 5.4 7.0 3.2 3.8 5.5
M5 6.4 8.5 3.8 4.3 6.5
M6 7.6 10.0 5.1 5.6 7.7
M8 9.7 12.0 6.5 7.0 9.8
Millimeters 3 4 5 6 8 10 12 14 16 18 20
Shank 001 003 004 006 008 010 012 013 014 016
Sheet thickness 0.5 - 0.6 0.7 - 0.8 0.9 - 1.0 1.1 - 1.3 1.4 - 1.6 1.7 - 1.9 2.0 - 2.2 2.3 - 2.5 2.6 - 2.8 2.9 - 3.1
WEMINOFF
Product name WEMINOFF-M4-008-12MM
Thread WEMINOFF-M4-008-12MM
Shank WEMINOFF-M4-008-12MM
Length WEMINOFF-M4-008-12MM
WEMINARB
Product name WEMINARB-M4-008
Thread WEMINARB-M4-008
Shank WEMINARB-M4-008
Dimension chart
WEMINOFF - Lengths
Material:
Steel, zinc plated
90
Locking miniature self-broaching nut
WEMINLOK is a self-broaching internal threaded locking nut
with a serrated shank.
rial, ensuring a strong and enduring joint. WEMINLOKs upper
portion of thread is distorted, thus making it an all-metal lock-
ing nut.
Benefts
Suits well for thin and hard materials
Suits well for light metals such as aluminium, magnesium, etc.
Suitable for materials with thickness between 0.5 - 3.0 mm
Removes the need for a locking washer

Installation
To achieve the best installation result, it is important to use a proper
riveting tool (see page 92). It is recommended to use a clamp to
achieve a constant result. Small amounts can also be installed by
hand tools.
Nut types
Usage
In order to achieve the best possible joint, it is recommended to
install the screw through the opposite side of the head, although it is
possible to attach the screw from the top face side.
91
Technical info: WEMINLOK
Thread
Shank
diameter A
mm
Head diam-
eter B mm
Head
height mm
Recommended
hole diameter
-0.00 + 0.10 mm
M3 4.2 5.5 2.8 4.3
M4 5.4 7 3.2 5.5
M5 6.4 8.5 3.8 6.5
M6 7.6 10 5.1 7.7
M8 9.7 12 6.5 9.8
Dimension chart
Shank 001 003 004 006 008 010 012 013 014 016
Sheet thickness 0.5 - 0.6 0.7 - 0.8 0.9 - 1.0 1.1 - 1.3 1.4 - 1.6 1.7 - 1.9 2.0 - 2.2 2.3 - 2.5 2.6 - 2.8 2.9 - 3.1
WEMINLOK
Product name WEMINLOK-M4-008
Thread WEMINLOK-M4-008
Shank WEMINLOK-M4-008
Material:
Steel, zinc plated and waxed
92
Installation guide Self-broaching
Types: WEARB, WEARBSO, WEMINARB, WEMINOFF, WEMINLOK
Self-broaching nuts are installed by clamping with a proper sized punch.
1. Punch or drill proper
sized mount hole to the
sheet metal.
2. Apply steady squeezing
force until the bottom face of
the fastener touches the sheet
metal.
3. Attach the desired object
into the sheet metal with a
fastener.
Punch sizes
Thread
WEARB & WEARBSO PUNCH WEMINARB, WEMINOFF & WEMINLOK PUNCH
A
mm
B
mm
C
mm
D
mm
E
mm
A
mm
B
mm
C
mm
D
mm
E
mm
M2 4.3 0.5 0.5 7.1 12.5 2.4 0.5 0.5 4.8 12.5
M2.5 4.3 0.5 0.5 7.1 12.5 3.1 0.5 0.5 5.5 12.5
M3 4.3 0.5 0.5 7.1 12.5 3.1 0.5 0.5 5.5 12.5
M3.5 5.3 0.6 0.5 8.7 12.5 4.3 0.5 0.5 7.1 12.5
M4 5.3 0.6 0.5 8.7 12.5 4.3 0.5 0.5 7.1 12.5
M5 6.8 0.8 0.5 10.3 16.0 5.3 0.5 0.5 8.7 12.5
M6 8.0 0.9 0.6 11.9 16.0 6.5 0.75 0.5 10.3 12.5
M8 11.1 1.0 0.6 15.5 19.0 8.5 0.75 0.5 12.4 16.0
M10 13.5 1.1 0.6 18.3 19.0 - - - - -
M12 17.1 1.3 0.6 22.2 25.0 - - - - -
All punches are made from quenched silver steel.
93
Test data Self-broaching
The following test data concerning the joints
can be given to the self-broaching nuts.
However, this data is only suggestive, as the
strength of the joint is afected by the mate-
rial properties, the mount hole diameter, the
method of installation, etc.
NOTE!
This data has been obtained by using sheet metal
63RB (116VPN) in laboratory conditions. This data
can difer from the true values. For more information
contact WE sales.
Push-out force resistance
Push-out resistance data of the joint when
pushed in with force.
Torque resistance
Torque resistance data of the joint when turned
with force.
WEARB
WEMINARB
WEARB
WEMINARB
P
u
s
h
-
o
u
t

f
o
r
c
e

(
N
)
T
o
r
q
u
e

r
e
s
i
s
t
a
n
c
e

(
N
m
)
P
u
s
h
-
o
u
t

f
o
r
c
e

(
N
)
T
o
r
q
u
e

r
e
s
i
s
t
a
n
c
e

(
N
m
)
Sheet metal thickness (mm)
94
Self-clinching nut
Self-clinching nuts WES and WECLS are internal threaded join-
ing elements, which are installed to a sheet metal by pressing.
The bottom face of the nut contains a serrated ring and a
groove, that when applied steady squeezing force, causes the
host material to steadily fow into the groove, creating strong
and enduring joining.
Benefts
High torque resistance
Level opposite side of the joining
Small and clean joining
Easy to install by clamping

Sheet metal material
Sheet metal material hardness must be less than 80 Rb (150 VPN).
Stainless steel sheet metal material hardness must be less than 70 Rb (128
VPN).
Sheet metal thickness
Self-clinching nuts and standofs can always be installed from thickness of
0.8 mm onwards, (M2-M5) depending on the size of the shank. See the
chart on the next page.
Shank selection
Always select the longest possible shank to ensure the
strongest possible joining.
Installation direction
Fastener installation to the joint is always recommend-
ed to be done from the opposite side of the head.
Installation
Installation should always be done by clamping. Nev-
er attempt to stamp the fastener to the sheet metal.
95
Self-clinching nut
Technical info: WES, WECLS
Thread
Shank
No.
Sheet metal
minimum
thickness mm
Shank
max.
length A
mm
Recommended
mounting hole
diameter
+0.08 - 0.00 mm
Shank
max.
diameter
C mm
Head
diameter
E mm
Head
length T
mm
Minimum dis-
tance from the
edge of the
sheet mm
M2
0 0.8 - 1.0 0.76
4.25 4.22 6.30 1.50 4.8
1 1.0 0.97
2 1.4 1.37
3 2.3 2.21
M2.5
0 0.8 - 1.0 0.76
4.25 4.22 6.30 1.50 4.8
1 1.0 0.97
2 1.4 1.37
3 2.3 2.21
M3
0 0.8 - 1.0 0.76
4.25 4.22 6.30 1.50 4.8
1 1.0 0.97
2 1.4 1.37
3 2.3 2.21
M3.5
0 0.8 - 1.0 0.76
4.75 4.73 7.10 1.50 5.6
1 1.0 0.97
2 1.4 1.37
3 2.3 2.21
M4
0 0.8 - 1.0 0.76
5.40 5.38 7.90 2.00 6.7
1 1.0 0.97
2 1.4 1.37
3 2.3 2.21
M5
0 0.8 - 1.0 0.76
6.40 6.34 8.70 2.00 7.0
1 1.0 0.97
2 1.4 1.37
3 2.3 2.21
M6
1 1.4 1.37
8.75 8.72 11.05 4.08 8.7 2 2.3 2.21
3 3.1 3.05
M8
1 1.4 1.37
10.50 10.44 12.65 5.47 9.5 2 2.3 2.21
3 3.1 3.05
M10
1 2.3 2.21
14.00 13.94 17.35 7.50 11.0 2 3.1 3.05
3 6.1 5.97
M12
1 3.1 3.05
16.0
2 6.1 5.97
WES
Product name WES-M4-1
Thread WES-M4-1
Shank WES-M4-1
WECLS
Product name WECLS-M4-1
Thread WECLS-M4-1
Shank WECLS-M4-1
Material:
- Steel, zinc plated WES
- Stainless steel WECLS
96
Self-clinching stud
Self-clinching studs WEFH and WEFHS are external threaded
joining elements, which are installed in to the sheet metal by
pressing.
The ribs and the groove at the bottom face of the stud shape
the host material creating a strong and enduring joining.
Benefts
Easy to install by pressing
Clean joining
Level opposite side of the joining

When installed, apply squeezing force sufciently enough to
achieve a steady embedment of the head. Using excess force
must be avoided. Installation squeezing force varies depend-
ing on the material of the sheet and the size of the fastener.
See page 104 for more information.
Noteworthy
In particular installation combinations depending on the size
of the fastener and the thickness of the sheet metal, the anvil
must be equipped with a countersink. Countersink is needed
for self-clinching studs M5 or less when installed in to a sheet
with thickness 1.5 mm or less. Self-clinching nuts M6 or larger
also require a countersink, when the sheet thickness is 2.5
mm or less.
The sheet metal material hardness must be less than 80 Rb (150 VPN).
Stainless steel sheet hardness must be less than 70 Rb (128 VPN).
Mount hole
Holes can be made by punching or drilling with -0.00 / +0.08 mm
tolerance.
97
Technical info: WEFH, WEFHS
Material:
- Steel, zinc plated WEFH
- Stainless steel WEFHS
Thread
Max. head
diameter E
mm
Min. sheet
thickness mm
Min. distance
to the edge
mm
Recommend-
ed mount
hole -0.00 +
0.10 mm
Countersink
mm
Max. recom-
mended
torque Nm
M2 3.35 1.0 4.8 1.96 2.6 0.20
M2.5 4.05 1.0 5.3 2.47 3.1 0.41
M3 4.70 1.0 5.5 2.97 3.6 0.84
M3.5 5.30 1.0 6.4 3.48 4.1 1.02
M4 6.00 1.0 7.0 3.96 4.6 1.92
M5 6.70 1.0 7.0 4.98 5.6 3.84
M6 8.20 1.5 8.0 5.97 6.6 8.02
M8 9.90 2.0 9.5 7.97 8.6 13.50
WEFH
Product name WEFH-M4-12
Thread WEFH-M4-12
Length WEFH-M4-12
Thread 6 8 10 12 14 15 16 18 20 25 30 40 50 60
M2 - 2.5
M3
M3.5 - 4
M5
M6
M8
WEFH, WEFHS lengths (L)
WEFHS
Product name WEFHS-M4-12
Thread WEFHS-M4-12
Length WEFHS-M4-12
Dimension chart
98
High strength studs
WEHFH high strength stud is designed for joints requiring
stronger joining, and where level embedment isnt neccessary.
Benefts
Easy to install by pressing
Clean and strong joining

Mount hole
It is recommended to create the mount hole by punching, even
though a drilled mount hole is sufcient. The mount hole has to be
clear of any metal shavings and the holes edges must not be too
chamfered or rough.
Installation
The installation has to be made by applying steady squeezing
force until in the right depth. See page 104 for more information.
The anvil countersink must be used as follows:
Thread Material
M4 0.80 - 1.19
M5 0.90 - 1.29
M6 1.00 - 1.49
M8 1.50 - 1.99
Sheet metal material hardness needs to be less than 80 Rb (150
VPN).
99
High strength studs Technical info: WEHFH
Material:
- Quenched steel, zinc plated
Thread
Head
diameter E
mm
Max. head
height T
mm
Max. non-
threaded
shank S
mm
Min. sheet
thickness
mm
Min. dis-
tance from
the edge of
the sheet
mm
Recom-
mended
mounting
hole diam-
eter -0.00 +
0.13 mm
Countersink
mm
Max. rec-
ommended
torque Nm
M4 6.16 1.00 2.20 0.8 8.00 4.00 5.0 3.5
M5 7.80 1.14 2.40 0.9 10.70 5.00 6.5 4.4
M6 9.40 1.27 2.80 1.0 11.50 6.00 7.5 10.0
M8 12.50 1.78 3.50 1.5 12.70 8.00 9.5 22.0
M10 15.70 2.30 6.20 2.3 13.70 10.00 11.5 37.0
WEFH
Product name WEHFH-M4-12-Z
Thread WEHFH-M4-12-Z
Length WEHFH-M4-12-Z
Thread 6 8 10 12 14 15 16 18 20 25 30 35 40 50 60
M4
M5
M6
M8
M10
Lengths (L)
Dimension chart
100
Self-clinching ush nut
WEF self-clinching fush nut is designed to create level sheet sur-
face on both sides of the joint.
When the nut is clamped it embeds itself in to the sheet by dis-
placing the host material causing the material to fow into the
groove, thus forming a strong and enduring joint.
Benefts
Allows the creation of a joint in places with limited space
Easy to install
High push-out force resistance
Level surface on both sides of the joint.
Mount hole
The mount hole tolerance has to be -0.00... + 0.08 mm
Sheet metal hardness
Stainless steel sheet hardness needs to be less than 70 Rb (128 VPN).
Installation
Installation has to be always done by applying constant squeezing force,
never by stamping.
See the chart on the next page.
Shank
It is recommended to use longest possible shank length that
the sheet metal thickness allows. This creates the strongest
possible joint.
Installation side
Installation to the joint is always recommended to be done
from the opposite side of the head (round face in this case).
101
Self-clinching ush nut Technical info: WEF
WEF
Product name WEF-M4-1
Thread WEF-M4-1
Shank WEF-M4-1
Dimension chart
Thread Shank No.
Metal sheet
thickness
mm
max. nut
length A
Mount hole
-0.00 +
0.08
Max.
shank
diameter C
mm
Frame A/F
H mm
Min. dis-
tance from
the edge of
the sheet
mm
M2
1 1.5 - 2.3 1.50
4.35 4.34 4.8 6.0
2 2.4 2.30
M2.5
M3
1 1.5 - 2.3 1.50
4.35 4.34 4.8 6.0
2 2.4 2.30
M3-3.5
1 1.5 - 2.3 1.50
5.40 5.39 6.4 6.7
2 2.4 2.30
M3.5
1 1.5 - 2.3 1.50
5.40 5.39 6.4 6.7
2 2.4 2.30
M4
1 1.5 - 2.3 1.50
7.35 7.34 7.9 7.0
2 2.4 2.30
M5
1 1.5 - 2.3 1.50
7.90 7.89 8.7 8.0
2 2.4 2.30
M6
3 3.2 - 3.9 3.00
8.75 8.74 9.5 8.7 4 4.0 - 4.7 3.80
5 4.8 4.60
Material:
- Stainless steel
102
Self-clinching standoff
WESO and WEBSO self-clinching standofs are designed to act
as standofs or spacers in the sheet metal.
When the standof is clamped it embeds itself in to the sheet
by displacing the host material causing the material to fow
into the groove, thus forming a strong and enduring joint.
Benefts
Creates a stationary joining element
Available as blind or thru-holed
Level surface on the opposite side of the joint
Clean installation
Broad range of sizes

Mount hole
The mount hole tolerance has to be -0.00... + 0.08 mm.
Installation
Installation has to be always done by applying constant
squeezing force, never by stamping.
The sheet metal hardness has to be less than 80 Rb
(150 VPN).
Stainless steel sheet hardness has to be less than 70 Rb
(128 VPN).
103
Technical info: WESO, WEBSO
WESO
Product name WESO-M4-12
Thread WESO-M4-12
Length WESO-M4-12
Dimension chart
Thread
Sheet
thickness
mm
Mount hole
+0.08
-0.00 mm
C
+0.00 -0.13
mm
A/F H
mm
Non-
threaded
part B
mm
Min. dis-
tance from
the edge of
the sheet
mm
M2.5 M3 >1.0 4.20 4.19 4.8 3.2 6.0
M3 - 3.5 >1.0 5.40 5.39 6.4 4.0 6.7
M3.5 >1.0 5.40 5.39 6.4 4.0 6.7
M4 >1.3 7.20 7.14 7.9 4.8 8.0
M5 >1.3 7.20 7.14 7.9 5.2 8.0
Material:
- Quenched steel, Zinc plated WESO & WEBSO
- Stainless steel WESOS & WEBSOS
WESO
Thread
WEBSO
Thread
WESO length 3 4 5 6 8 10 12 14 16 18 20 22 24 25 26
Non-threaded length M3-M5 NONE 4.0 8.0 11.0
WESO length 3 4 5 6 8 10 12 14 16
Non-threaded length M3-M5 NONE 4.0 8.0
WEBSO length 6 8 10 12 14 16 18 20 22 24 25 26
Non-threaded length M3-M5 3.2 4.0 6.5 9.5
WEBSO length 6 8 10 12 14 16
Non-threaded length M2.5 3.2 4.0 6.5
WEBSO
Product name WEBSO-M4-12
Thread WEBSO-M4-12
Length WEBSO-M4-12
104
Suggestive installation force chart (kN) for WES Press-in fasteners
Thread
NS4
1
/
2
Aluminium alloy
H515W
Aluminium alloy
1
/
2

hard brass
Cold rolled steel
M2 & M2.5 7.5 - 10 15 - 17.5 10 - 12.5 7.5 - 10
M3 & M3.5 12.5 - 15 17.5 - 20 15 - 17.5 10 - 12.5
M4 12.5 - 15 20 - 22.5 20 - 22.5 10 - 12.5
M5 12.5 - 15 20 - 22.5 20 - 22.5 12.5 - 15
M6 22.5 - 25 42.5 - 45 35 - 37.5 20 - 22.5
M8 30 - 32.5 45 - 47.5 35 - 37.5 22.5 - 30
M10 30 - 32.5 50 - 52.5 50 - 52.5 27.5 - 30
M12 35 - 37.5 70 - 72.5 70 - 72.5 42.5 - 45
All self-clinching fasteners
are easy to install without
special tools. Self-clinching
fastener is installed by ap-
plying constant squeezing
force. It is recommended
to install the fastener into a
punched or drilled mount
hole.
WES & WECLS self-clinching nut installation
1. Drill or punch a proper sized hole
into a sheet metal and install the press-in
fastener directly into the place.
2. Clamp the fastener steadily with a right
sized tool above the fastener until the head is
embedded into the sheet.
3. Fasten the desired fastener from
the opposite side.
WEF Self-clinching fush nut installation
1. Drill or punch a proper sized hole
into a sheet metal and install the press-in
fastener directly into the place.
2. Clamp the fastener steadily above the
nut until the hexagon head of the nut embeds
into the sheet metal.
3. Fasten the desired fastener from the
opposite side of the hexagon head.
WESO & WEBSO self-clinching standof installation
1. Drill or punch a proper sized hole in to the
sheet metal.
2. Clamp the fastener above the standof until
the hexagon head is embedded into the sheet.
3. Fasten the desired screw from the opposite
side of the hexagon head.
Thread
Counter sink
diameter
M2.5 4.3 - 4.4
M3 5.5 - 5.6
M3.5 5.5 - 5.6
M4 7.2 - 7.3
M5 7.2 - 7.3
Self-clinching fastener installation
105
Thread
Anvil
A
mm
C
mm
M2 2.59 - 2.69 2.01 - 2.08
M2.5 3.10 - 3.20 2.53 - 2.61
M3 3.61 - 3.71 3.02 - 3.10
M3.5 4.12 - 4.22 3.53 - 3.61
M4 4.60 - 4.70 4.01 - 4.07
M5 5.66 - 5.77 5.03 - 5.11
M6 7.14 - 7.26 6.01 - 6.07
M8 9.14 - 9.26 8.01 - 8.08
The installation of WEFH & WEFHS self-clinching studs
Anvil
Punch
Stud
Stud length
+6.35mm (1/4)
Punch Anvil
Diameter D
mm
Depth F
mm
Min.
length
Hole diameter
C mm
Countersink
A mm
Sheet metal
thickness mm
Thread
M4 6.6 - 6.8 0.85 - 0.90 L 4.10 - 4.15 4.6 - 4.7 0.80 - 1.19
M5 8.2 - 8.4 0.99 - 1.04 L 5.10 - 5.15 5.8 - 5.9 0.90 - 1.29
M6 9.8 - 10.0 1.12 - 1.17 L 6.10 - 6.15 7.0 - 7.1 1.00 - 1.49
M8 12.9 - 13.1 1.63 - 1.68 L 8.10 - 8.15 9.0 - 9.1 1.50 - 1.99
M10 16.1 - 16.3 2.10 - 2.12 L 10.10 - 10.15 - -
Tool dimension chart
The installation of WEHFH & WEHFHS high strength studs
Installation instructions
Normal anvil
Anvil for sheet
metals Punch Installation
Stud
Punch
Sheet
Anvil
106
Technical properties
Torque
Thread Thread
T
o
r
q
u
e

(
N
m
)
Thread
Thread
P
u
s
h
-
o
u
t

f
o
c
e

(
N
)
P
u
s
h
-
o
u
t

f
o
r
c
e

(
N
)
Push-out
Thread Thread
P
u
l
l
-
t
h
r
o
u
g
h

f
o
r
c
e

(
N
m
)
Pull-through
The following images indicate the
results of torsion, push-out and pull-
through tests.
Torque
Push-out force
Pull-through force
These results are suggestive and have been tested in
laboratory conditions using metal sheet 68 Rb (126
VPN).
107
Product code Thread
Sheet
thickness
mm
Width
across fats
sw
mm
Mount hole
diameter d
H11 mm
d1 -0.10
diameter
mm
d2 -0.10
diameter
mm
Shank
length h1
-0.15 mm
Height h
mm
037702 005 500 M2 1 mm 5.5 4.5 4.5 4.70 0.9 3.0
0377023 005 500 M2.3 1 mm 5.5 4.5 4.5 4.70 0.9 3.0
0377025 005 500 M2.5 1 mm 5.5 4.5 4.5 4.70 0.9 3.0
0377026 005 500 M2.6 1 mm 5.5 4.5 4.5 4.70 0.9 3.0
037703 005 500 M3 1 mm 5.5 4.5 4.5 4.70 0.9 3.0
037704 005 500 M4 1 mm 7.0 5.5 5.5 5.75 0.9 3.2
037705 005 200 M5 1 mm 8.0 6.5 6.5 6.75 0.9 4.0
037706 005 200 M6 1 mm 10.0 8.0 8.0 8.30 0.9 5.0
037708 005 200 M8 2 mm 13.0 10.0 10.0 10.30 1.9 6.5
037710 005 100 M10 2 mm 15.0 12.5 12.5 12.85 1.9 8.0
037712 005 100 M12 3 mm 17.0 14.5 14.5 14.75 2.9 10.0
037716 005 50 M16 3 mm 22.0 18.5 18.5 18.75 2.4 13.0
037720 005 50 M20 4 mm 27.0 23.0 23.0 23.40 3.9 16.0
KALEI clinch nut
The KALEI clinch nut is installed manually or by clamping into a
drilled or punched mount hole.
The shank of the nut has been rifed in order to ensure much
higher torque resistance in the joint.
The KALEI clinch nut is precision made and suits for automatic
feeding.
Manual hand tool:
KALEI hand tool is needed for manual
installation.
Clamp:
A simple clamp and feeding device can
be used in mass production.
108
Rivet nuts
Tools are important when using rivet nuts. They are strong and easy to use. The
nosepiece and cap screw are easy to replace. A single tool suits for the installation
of various sizes. Easy to use manual, pneumatic and hydraulic tools are available
for use. The rivet nuts are placed into drilled or punched mount holes. The rivet nut
is then placed into the nosepiece manually or automatically, depending on the
type of the tool. When the jaw pusher is drawn out the non-threaded part of the
nut expands radially, thus riveting the nut into the material. Turning the cap screw
counter-clockwise releases the tool from the nut.
When the material is thin, using rivet nuts is a simple and ideal
way of creating a threaded joint.
The rivet nut suits well for materials with thickness of 0.25 to
8.00 mm.
Available in diferent materials: Steel, aluminium and stainless
steel.
Thread range: M3 M12
Shank models
Round:
Most common when using normal load on
a steel sheet.
Round, Rifed:
Grants higher torque resistance.
Hexagon:
Grants the highest torque resistance with
high loads.
Head models
Pan head:
Most common when joint surface isnt
required to be level.
Flat head:
Used when the joint surface needs to be
level.
Reduced Head:
Used when the joint surface needs to be
level with the sheet metal.
Thru-holed or blind model
Thru-holed:
Most common when an efcient and strong
penetrating internal thread, without the need
for sealing, is required.
Blind:
Grants liquid proof sealing, which protects
the joint from corrosion or dirt. Important
when the joint is painted and the thread isnt
protected.
Tools
109
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill
diam-
eter
Shear
force N
Pull-out
force N
Max.
torque
Nm
79484 10 M4 0.25 2 6.0 9.0 10.0 6.10 3 246 5 500 3.1
79485 12 M5 0.5 3.0 6.9 10.0 12.0 7.10 3 460 8 900 6.9
79486 14 M6 0.5 3 8.9 13.0 14.5 9.10 6 141 10 650 12.1
79488 16 M8 0.5 3 10.9 15.0 16.0 11.10 8 708 12 600 19.3
794810 19 M10 1.0 3.5 13.0 17.0 19.0 13.10
Round rivet nut, fange head, knurled
Stainless steel A2
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill
diam-
eter
Shear
force N
Pull-out
force N
Max.
torque
Nm
794844 11 M4 0.5 2 6.0 7.0 11.0 6.10 2 385 6 000 2.2
794845 12 M5 0.5 3 6.9 8.0 12.0 7.10 3 012 8 100 3.2
794846 14 M6 0.5 3 8.9 10.0 14.5 9.10 5 158 10 120 5.8
794848 16 M8 0.5 3 10.9 12.0 16.0 11.10 6 815 14 000 15.6
Round rivet nut, reduced head, knurled
Stainless steel A2
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill
diam-
eter
Shear
force N
Pull-out
force N
Max.
torque
Nm
794874 10 M4 0.5 2.5 5.9 6.8 10.6 6.00 3 750 6 500 4.9
794875 11 M5 0.5 3 6.9 8.0 11.6 7.00 4 900 13 000 8.8
794876 14 M6 0.7 3 8.9 10.0 14.5 9.00 8 000 19 000 15.5
794878 15 M8 0.8 3.3 10.9 12.0 15.8 11.00 8 400 33 000 26.5
Half-Hexagon rivet nut, reduced head
Stainless steel A2
110
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill di-
ameter
Shear
force N
Pull-out
force N
Max.
torque
Nm
494814 9 M4 0.25 3 6.0 9.0 9.5 6.10 2 836 5 150 3.0
494814 12 M4 3 4.5 6.0 9.0 12.3
494815 12 M5 0.25 3 6.9 10.0 12.0 7.10 3 816 8 600 7.0
494815 15 M5 3 5.5 6.9 10.0 15.0
494816 14 M6 0.5 6 8.9 13.0 14.5 9.10 5 707 10 620 12.0
494816 16 M6 3 5.5 8.9 13.0 16.5
494818 16 M8 0.5 3 10.9 16.0 16.5 11.10 10 156 12 300 23.0
494811019 M10 0.5 3.5 13.0 19.0 19.5 13.10 10 473 15 000 39.0
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill di-
ameter
Shear
force N
Pull-out
force N
Max.
torque
Nm
494844 10 M4 0.5 2 6.0 7.0 10.4 6.10 2 786 5 950 2.9
494845 12 M5 0.5 3 6.9 8.0 11.5 7.10 3 942 8 340 6.0
494846 14 M6 0.5 3 8.9 10.0 14.5 9.10 5 675 9 960 10.5
494848 16 M8 0.8 4.5 10.9 12.0 16.8 11.10 8 525 10 600 15.5
Round rivet nut, serrated fange head, knurled
Zinc plated steel
Round rivet nut, reduced head, knurled
Zinc plated steel
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill
diam-
eter
Shear
force N
Pull-out
force N
Max.
torque
Nm
59484 10 M4 0.25 2 6.0 9.0 10.0 6.1 2 836 7 500 4.8
59485 13 M5 0.5 3.0 6.9 10.0 13.0 7.1 3 567 9 800 6.5
59486 14 M6 0.5 3.0 8.9 13.0 14.5 9.1 4 521 10 600 22.0
59488 16 M8 0.5 3.0 10.9 16.0 16.5 11.1 8 536 13 000 40.0
594810 21 M10 0.5 3.0 13.0 19.0 21.0 13.1 9 721 17 250 88.0
Hexagon rivet nut, fange head
Zinc plated steel
111
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill
diam-
eter
Shear
force N
Pull-out
force N
Max.
torque
Nm
694844 10 M4 0.5 2 6.3 7.8 10.5 6.40 2 822 5 900 4.6
694845 12 M5 0.5 2.5 7.1 8.8 12.0 7.20 3 451 9 250 6.2
694846 15 M6 0.7 3 9.5 11.2 15.0 9.60 4 285 9 950 19.0
694848 16 M8 0.8 3 10.5 12.2 16.0 10.60 5 632 12 200 34.0
Half-hexagon rivet nut, reduced head
Zinc plated steel
Product
code
Thread
Material
hardness E
Hull d1
Flange
d2
Length
Drill di-
ameter
Shear
force N
Pull-out
force N
Max.
torque
Nm
694894 10 M4 0.5 2 5.9 6.8 10.6 6.10 2 822 5 900 4.6
694895 11 M5 0.5 3 6.9 8.0 11.6 7.10 3 451 9 250 6.2
694896 14 M6 0.5 3 8.9 10.0 14.5 9.10 4 285 9 950 19.0
Half-hexagon rivet nut, miniaturized, reduced head
Zinc plated steel
112
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force N
093724 4 2.4x4 0.5 2.0 5 2.50 0.55 1.45 400 500
093724 6 2.4x6 2.0 4.0
096724 8 2.4x8 4.0 6.0
093732 6 3.2x6 1.5 3.5 6,5 3.30 0.80 1.80 880 1 150
093732 8 3.2x8 3.5 5.5
093732 833 3.2x8 Black 3.5 5.5
093732 820 3.2x8 White 3.5 5.5
093732 10 3.2x10 5.5 7.0
093732 12 3.2x12 7.0 9.0
09374 6 4.0x6 1.5 3.0 8 4.10 1.00 2.20 1 300 1 960
09374 8 4.0x8 3.0 5.0
09374 10 4.0x10 5.0 6.5
09374 12 4.0x12 6.5 8.5
093748 6 4.8x6 0.5 3.0 9,5 4.90 1.10 2.75 1 870 2 790
093748 8 4.8x8 3.0 4.5
093748 10 4.8x10 4.5 6.0
039748 12 4.8x12 6.0 8.0
Aluminium / Steel
Dome head
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force N
093832 6 3.2x6 1.5 3.5 6 3.30 0.90 1.80 880 1 150
093832 8 3.2x8 3.5 5.5
093832 10 3.2x10 5.5 7.0
093832 12 3.2x12 7.0 9.0
09384 6 4.0x6 1.5 3.0 7.5 4.10 1.00 2.20 1 300 1 960
09384 8 4.0x8 3.0 5.0
09384 10 4.0x10 5.0 6.5
09384 12 4.0x12 6.5 8.5
093848 6 4.8x6 0.5 3.0 9 4.90 1.20 2.75 1 870 2 790
093848 8 4.8x8 3.0 4.5
093848 10 4.8x10 4.5 6.0
093848 12 4.8x12 6.0 8.0
Aluminium / Steel
Flat head 120
Blind rivets
113
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force N
093932 6 3.2x6 1.5 3.5 6.5 3.30 0.80 1.80 880 1 150
093932 8 3.2x8 3.5 5.5
093932 10 3.2x10 5.5 7.0
093932 12 3.2x12 7.0 9.0
09394 6 4.0x6 1.5 3.0 8 4.10 1.00 2.20 1 300 1 960
09394 8 4.0x8 3.0 4.5
09394 10 4.0x10 4.5 6.5
09394 12 4.0x12 6.5 8.5
093948 6 4.8x6 0.5 3.0 9.5 4.90 1.10 2.75 1 870 2 790
093948 8 4.8x8 3.0 4.5
093948 10 4.8x10 4.5 6.0
093948 12 4.8x12 6.0 8.0
Aluminium / Stainless steel
Dome head
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force N
09370326 3.2x6.5 0.5 2.0 6 3.30 0.90 1.70 1 160 1 400
09370328 3.2x8 3.0 3.5
093703295 3.2x9.5 3.5 5.0
093703211 3.2x11 5.0 6.5
093704 8 4.0x8 0.5 3.5 8 4.10 1.40 2.20 1 860 2 500
093704 95 4.0x9.5 3.5 5.0
093704 11 4.0x11 5.0 6.5
093704885 4.8x8.5 0.5 3.5 9.5 4.90 1.50 2.60 2 400 3 400
093704895 4.8x9.5 3.5 5.0
093704811 4.8x11 5.0 6.5
Aluminium / Steel
Dome head, pressure resistant
114
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force
393732 6 3.2x6 0.5 2.0 6 3.30 0.80 1.70 1 160 1 400
393732 8 3.2x8 2.0 3.5
393732 95 3.2x9.5 3.5 5.0
39374 8 4.0x8 0.5 3.5 8 4.10 1.30 2.20 1 860 2 500
39374 95 4.0x9.5 3.5 5.0
39374 11 4.0x11 5.0 6.5
393748 8 4.8x8 0.5 3.0 9.5 4.90 1.50 2.65 2 400 3 400
393748 95 4.8x9.5 3.5 5.0
393748 11 4.8x11 5.0 6.5
Aluminium / Stainless steel
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force
393704810 4.8x10 4.5 6.0 9.5 4.90 1.50 2.60 2 400 3 400
393704812 4.8x12 6.0 8.0
Aluminium / Steel
Flat head 120, pressure resistant
115
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force
493732 8 3.2x8 0.5 2.0 6.3 3.30 1.40 1.80 490 450
493732 95 3.2x9.5 2.0 5.0
49374 95 4.0x9.5 3.5 5.0 8 4.10 1.70 2.20 710 580
49374 125 4.0x12.5 5.0 8.0
493748 95 4.8x9.5 3.5 5.0 9.5 4.90 2.00 2.65 1 100 940
493748 115 4.8x11.5 5.0 6.5
493748 125 4.8x12.5 6.0 7.5
Aluminium / Aluminium
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force
093532 60 3.2x6 1.5 3.5 6.5 3.30 0.80 2.00 1 400 1 700
093532 80 3.2x8 3.5 5.5
093532 10 3.2x10 5.5 7.0
093532 12 3.2x12 7.0 9.0
093532 14 3.2x14 9.0 - 11
09354 6 4.0x6 1.5 3.0 8 4.10 1.00 2.40 2 000 2 400
09354 8 4.0x8 3.0 5.0
09354 10 4.0x10 5.0 6.5
09354 12 4.0x12 6.5 8.5
093548 6 4.8x6 0.5 3.0 9.5 4.90 1.10 2.95 3 000 4 100
093548 8 4.8x8 3.0 4.5
093548 10 4.8x10 4.5 6.0
093548 12 4.8x12 6.0 8.0
09355 8 5.0x8 3.0 4.5 9.5 5.10 1.10 2.95 3 500 4 800
Steel / Steel
Dome head
116
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force
293504 8 4.0x8 3.0 5.0 7.5 4.10 1.00 2.40 2 000 2 400
293504 10 4.0x10 5.0 6.5
293504 12 4.0x12 6.5 8.5
29350488 4.8x8 3.0 4.5 9 4.90 1.20 2.95 3 000 4 100
293504810 4.8x10 4.5 6.0
293504812 4.8x12 6.0 8.0
Steel / Steel
Flat head 120
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force
09350328 3.2x8 0.5 3.0 6 3.30 1.00 1.90 1 100 1 200
093503295 3.2x9.5 1.0 4.5
093503212 3.2x12 4.0 7.0
093504 8 4.0x8 0.5 3.5 8 4.10 1.40 2.30 1 700 1 860
093504 10 4.0x10 1.0 5.0
093504 12 4.0x12 5.0 7.5
093504895 4.8x9,5 1.0 4.0 9.5 4.90 1.70 2.90 2 400 2 840
093504812 4.8x12 4.0 6.0
Steel / Steel
117
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force N
093132 60 3.2x6 1.0 3.0 6.2 3.30 1.00 2.10 2 500 2 750
093132 80 3.2x8 3.0 5.0
093132 10 3.2x10 5.0 7.0
093132 12 3.2x12 6.0 9.0
09314 6 4.0x6 1.0 3.0 8 4.10 1.30 2.40 3 500 4 000
09314 8 4.0x8 3.0 5.0
09314 10 4.0x10 5.0 6.5
09314 12 4.0x12 6.5 8.5
093148 8 4.8x8 1.0 3.0 8.7 4.90 1.40 3.10 4 500 5 500
093148 10 4.8x10 4.0 6.0
093148 12 4.8x12 6.0 8.0
Stainless steel / Stainless steel
Dome head
Product code d1 x L
Material
strength
d2
Drill
diam-
eter
k w
Shear
force N
Pull-out
force N
09310328 3.2x8 0.5 3.0 6 3.30 1.00 1.90 1 100 1 200
093103595 3.2x9.5 1.0 4.5
093104 8 4.0x8 0.5 3.0 8 4.10 1.40 2.30 1 700 1 860
093104 95 4.0x9.5 1.0 4.5
093104 12 4.0x12 4.5 7.5
093104895 4.8x9.5 1.0 4.0 9.5 4.90 1.40 2.90 2 400 2 840
093104812 4.8x12 4.0 6.0
Stainless steel / Stainless steel
118
Weld stud
Product code Dimensions
10143 10 M3X10
10143 16 M3X16
10143 20 M3X20
10143 25 M3X25
10143 30 M3X30
10143 6 M3X6
10143 8 M3X8
10144 10 M4X10
10144 12 M4X12
10144 16 M4x16
10144 20 M4X20
10144 25 M4x25
10144 30 M4X30
10144 6 M4x6
10144 8 M4x8
10145 10 M5X10
10145 12 M5x12
10145 15 M5X15
10145 16 M5X16
10145 20 M5X20
10145 25 M5X25
10145 30 M5X30
10145 40 M5X40
10145 8 M5x8
10146 10 M6X10
10146 12 M6X12
10146 16 M6X16
10146 20 M6X20
10146 25 M6x25
10146 30 M6X30
10146 40 M6X40
10148 16 M8X16
10148 20 M8X20
10148 25 M8X25
10148 30 M8X30
10148 40 M8X40
Product Code Dimensions
20143 16 M3X16
20143 6 M3X6
20144 10 M4X10
20144 12 M4X12
20144 16 M4X16
20144 25 M4X25
20145 10 M5X10
20145 12 M5X12
20145 16 M5X16
20145 50 M5X50
20146 10 M6X10
20146 12 M6X12
20146 15 M6x15
20146 16 M6X16
20146 20 M6X20
20146 25 M6x25
20148 15 M8X15
20148 20 M8x20
20148 25 M8X25
20148 30 M8X30
d M3 M4 M5 M6 M8
h 0.6 0.6 0.7 0.8 1
d1 0.55 0.55 0.8 0.8 0.5
d2 4.5 5.5 6.5 7.8 9
Weld stud 32501
Stainless steel A2
Weld stud 32501
Steel, copper plated CU/ST
119
Material
Prod.
group
Material
Prod.
group
Steel 0399 Stainless steel 03992
height m 3 3.5 4 5 5.5 6.5 8 10 11 13
Height h1 0.55 0.65 0.7 0.75 0.8 0.9 1.15 1.4 1.8 1.8
Diameter e min. 8.15 9.83 10.95 12.02 13.14 15.38 18.74 20.91 24.27 26.51
Diameter d2 4.5 6 7 8 9 10.5 12.5 14.8 16.8 18.8
Dimension chart
DIN 929
Weld nut
Hexagon weld nut
Material
Prod.
group
Steel 0385
Height h 7.0 8.5 10.0 12.0 12.5
Base width b 11.0 13.5 18,0 18.0 19.0
Base length d4 19.0 22.0 26.0 26.0 28.0
Diameter d2 6.5 7.6 11.0 12.5 14.0
Dimension chart
Weld nut
Slab base weld nut
Test loads: Separate chart DIN 929
120
15%
85%
FASTENER
PROCUREMENT
COSTS
OTHER COSTS
85%
Procurement
Shipping
Storing
Production planning
Component picking
File upkeep
Intermediate storing
Threading
Hole creation
Tool maintenance
Object alignment
Fastener installation and tightening
Intermediate and fnal inspection
Wrth Elektronik Oy Karhutie 4 01900 Nurmijrvi Tel +358 10 308 4700 Fax +358 10 308 4701 www.wurthelektronik.f
Total cost of creating a joint
Correct quality
Correct fasteners
At the right time
In the right place
Correct information
r
t
h

E
l
e
k
t
r
o
n
i
k

O
y

1
0
/
2
0
1
2

K
A

2
0
0
/
1
3
0

g
/
m
2

a
r
t

s
i
l
k

1
0
0
0

WE Fasteners

Uploaded by

WE Fasteners

Uploaded by

Fasteners

more than you expect

You might also like