Srs

H RESTRAINTS
SECTION
SRS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
CONTENTS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) AIR BAG and SEAT BELT PRE-TENSIONER .................................................................. 3
Precautions for SRS AIR BAG and SEAT BELT
PRE-TENSIONER Service ..................................... 3
Occupant Classification System Precaution ............ 3
Trouble Diagnosis Precaution .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) ....... 5
SRS Configuration ................................................... 5
Front Seat Belt Pre-tensioner with Load Limiter ..... 6
Front Side Air Bag .................................................... 6
Side Curtain Air Bag ................................................. 6
Occupant Classification System ............................... 6
Direct-connect SRS Component Connectors ........... 7
TROUBLE DIAGNOSIS .............................................. 8
Trouble Diagnosis Introduction ................................. 8
DIAGNOSIS FUNCTION ....................................... 8
HOW TO PERFORM TROUBLE DIAGNOSES
FOR QUICK AND ACCURATE REPAIR ............... 8
WORK FLOW ........................................................ 9
SRS Components Parts Location ........................... 10
Schematic ...............................................................11
Wiring DiagramSRS ........................................... 12
CONSULT-II Function (AIR BAG) ........................... 18
CONSULT-II Function ............................................ 18
HOW TO CHANGE SELF-DIAGNOSIS MODE
WITH CONSULT-II .............................................. 18
HOW TO ERASE SELF-DIAGNOSIS RESULTS... 19
Self-Diagnosis Function (Without CONSULT-II) ..... 19
HOW TO CHANGE SELF-DIAGNOSIS MODE... 19
HOW TO ERASE SELF-DIAGNOSIS RESULTS... 20
SRS Operation Check ............................................ 20
DIAGNOSTIC PROCEDURE 1 ........................... 20
Trouble Diagnosis With CONSULT-II ..................... 22
Revision: July 2007
DIAGNOSTIC PROCEDURE 4 (CONTINUED

FROM DIAGNOSTIC PROCEDURE 2) .............. 31
Trouble Diagnosis Without CONSULT-II ................. 38
WARNING LAMP FLASH CODE CHART ........... 39
Trouble Diagnosis: AIR BAG Warning Lamp Does
Not Turn Off ............................................................ 44
Trouble Diagnosis: AIR BAG Warning Lamp Does
Not Turn On ............................................................ 45
DRIVER AIR BAG MODULE .................................... 46
Removal and Installation ........................................ 46
REMOVAL ........................................................... 46
INSTALLATION ................................................... 47
SPIRAL CABLE ........................................................ 48
REMOVAL ........................................................... 48
INSTALLATION ................................................... 50
FRONT PASSENGER AIR BAG MODULE .............. 51
REMOVAL ........................................................... 51
INSTALLATION ................................................... 51
WIRING HARNESS MODIFICATION .................. 52
SIDE CURTAIN AIR BAG MODULE ........................ 54
REMOVAL ........................................................... 54
INSTALLATION ................................................... 54
CRASH ZONE SENSOR ........................................... 56
REMOVAL ........................................................... 56
INSTALLATION ................................................... 56
SIDE AIR BAG (SATELLITE) SENSOR ................... 57
REMOVAL ........................................................... 57
INSTALLATION ................................................... 57
FRONT SEAT BELT PRE-TENSIONER ................... 58
SRS-1
2005 Armada
SRS
DIAGNOSIS SENSOR UNIT ..................................... 59

REMOVAL ........................................................... 59
INSTALLATION .................................................... 59
ECU DISCRIMINATED NO. ................................. 59
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT ................................................................ 60
COLLISION DIAGNOSIS .......................................... 61
For Frontal Collision ................................................ 61
Revision: July 2007
SRS INSPECTION (FOR FRONTAL COLLISION) ...................................................................61

For Side and Rollover Collision ...............................62
WHEN SRS IS ACTIVATED IN THE SIDE OR
ROLLOVER COLLISION .....................................62
WHEN SRS IS NOT ACTIVATED IN THE SIDE
OR ROLLOVER COLLISION ...............................62
SRS INSPECTION (FOR SIDE AND ROLLOVER
COLLISION) .........................................................63
SRS-2
2005 Armada
PRECAUTIONS
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER
EHS0028X
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for SRS AIR BAG and SEAT BELT PRE-TENSIONER Service
EHS0028Y
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
SRS
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bags and seat belt
I
pre-tensioners to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.
The air bag diagnosis sensor unit must always be installed with the arrow mark pointing toward the
front of the vehicle for proper operation. Also check air bag diagnosis sensor unit for cracks, deformities or J
rust before installation and replace as required.
The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to
K
turn steering wheel or column after removal of steering gear.
Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad
side facing upward and seat mounted front side air bag module standing with the stud bolt side facing
L
down.
Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
After air bag inflates, the front instrument panel assembly should be replaced if damaged.
M
Occupant Classification System Precaution
EHS0028Z
Replace control unit and passenger front seat cushion as an assembly.
Trouble Diagnosis Precaution
EHS00290
When you read wiring diagrams, refer to the following:
GI-15, "How to Read Wiring Diagrams" in GI section
PG-4, "POWER SUPPLY ROUTING CIRCUIT" in PG section

When you perform trouble diagnosis, refer to the following:
GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section
GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section

Check for any service bulletins before servicing the vehicle.
Revision: July 2007
SRS-3
2005 Armada
PREPARATION
PREPARATION
Special Service Tools
PFP:00002
EHS00291
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
(J-42057-UPD)
Air bag key set
Part of kit (J-42057)
Removing and installing air bag lock
LRS210
Commercial Service Tools
EHS00292
(Kent-Moore No.)
Tool name
Description
(J-1859A)
Steering wheel puller
Removing steering wheel
LHIA0043E
(J-42578)
Steering wheel puller legs
Removing steering wheel
LHIA0044E
Revision: July 2007
SRS-4
2005 Armada

SRS Configuration
PFP:28556
A
EHS00293
SRS
I
WHIA0219E
The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
The collision modes for which supplemental restraint systems are activated are different among the SRS systems. For example, the driver air bag module, front passenger air bag module, seat belt buckle pre-tensioner
assemblies and the front seat belt pre-tensioners are activated in a frontal collision but not in a side collision.
SRS configurations for some collision modes are as follows:
Frontal collision
Left side collision
Right side collision
Rollover
Driver air bag module
Front passenger air bag module
Front LH seat belt pre-tensioner
Seat belt buckle pre-tensioner assembly LH
Front RH seat belt pre-tensioner
Seat belt buckle pre-tensioner assembly RH
Front LH side air bag module (If equipped)
Front RH side air bag module (If equipped)
LH side front curtain air bag module
LH side rear curtain air bag module
RH side front curtain air bag module
RH side rear curtain air bag module
SRS configuration
Revision: July 2007
SRS-5
2005 Armada

Front Seat Belt Pre-tensioner with Load Limiter
The seat belt pre-tensioner system with load limiter is installed for
both the driver's seat and the front passenger's seat. It operates
simultaneously with the SRS air bag system in the event of a frontal
collision with an impact exceeding a specified level.
When the frontal collision with an impact exceeding a specified level
occurs, seat belt slack resulting from clothing or other factors is
immediately taken up by the pre-tensioner. Vehicle passengers are
securely restrained.
When passengers in a vehicle are thrown forward in a collision and
the restraining force of the seat belt exceeds a specified level, the
load limiter permits the specified extension of the seat belt by the
twisting of the ELR shaft, and a relaxation of the chest-area seat belt
web tension while maintaining force.
Front Side Air Bag
EHS00294
SRS444
EHS00295
Front side air bag modules are built into the front seatback assemblies.
Vehicles with side air bags are equipped with labels as shown.
WHIA0008E
Side Curtain Air Bag
EHS00296
Side curtain air bag modules are located above the vehicle headlining.
Vehicles with side curtain air bags are equipped with labels as
shown.
WHIA0041E
Occupant Classification System
EHS00297
The occupant classification system identifies different size occupants, out of position occupants, and detects if
child seat is present in the front passenger seat. The occupant classification system receives inputs from the
occupant classification system sensor (located inside the passenger seat cushion assembly) and belt tension
sensor (part of the passenger front seat belt assembly and located at the belt anchor location). Depending on
classification of passenger, the occupant classification system sends a signal to the air bag diagnosis sensor
unit. The air bag diagnosis sensor unit uses this signal to determine deployment or non deployment of the passenger front air bag in the event of a collision. Depending on the signal received, the air bag diagnosis sensor
Revision: July 2007
SRS-6
2005 Armada

unit can disable the passenger front air bag completely. If this occurs the air bag diagnosis sensor unit will turn
on the PASS AIR BAG OFF indicator.
D
WHIA0187E
Direct-connect SRS Component Connectors
EHS00298
The following SRS components use direct-connect style harness connectors.
Front passenger air bag module
LH side front curtain air bag module
LH side rear curtain air bag module
RH side front curtain air bag module
RH side rear curtain air bag module
Front LH seat belt pre-tensioner
Seat belt buckle pre-tensioner assembly LH
Seat belt buckle pre-tensioner assembly RH

Always pull up to release black locking tab prior to removing connector from SRS component.
Always push down to lock black locking tab after installing connector
to SRS component. When locked, the black locking tab is level with
the connector housing.
SRS
L
WHIA0103E
Revision: July 2007
SRS-7
2005 Armada
TROUBLE DIAGNOSIS
TROUBLE DIAGNOSIS
Trouble Diagnosis Introduction
PFP:00004
EHS00299
CAUTION:
Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in
this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness connectors.
Do not attempt to repair, splice or modify SRS wiring harnesses. If a harness is damaged, replace
it with a new one.
Keep ground connections clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read by using AIR BAG warning lamp and/or CONSULT-II.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system malfunction through the operation of the AIR BAG warning lamp.
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the AIR BAG warning lamp and CONSULT-II are as follows:
User mode
Diagnosis mode
Display type
AIR BAG warning lamp
ON-OFF operation
CONSULT-II
Monitoring
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR

A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symptoms or conditions for a customer complaint.
Information From Customer

WHAT - Vehicle model
WHEN - Date, Frequencies
WHERE - Road conditions
HOW - Operating conditions, Symptoms
Preliminary Check
Check that the following parts are in good order.
Battery (Refer to SC-4, "How to Handle Battery" .)
Fuse (Refer to SRS-12, "Wiring DiagramSRS" .)
System component-to-harness connections
Revision: July 2007
SRS-8
2005 Armada
TROUBLE DIAGNOSIS
WORK FLOW
A
SRS
L
WHIA0098E
*1: SRS-8
*2: SRS-20
*3: SRS-31
*4: SRS-38
Revision: July 2007
SRS-9
2005 Armada
TROUBLE DIAGNOSIS
SRS Components Parts Location
EHS0029A
WHIA0216E
1.
Side curtain air bag modules
2.
Front RH side air bag module

(If equipped)
3.
RH side air bag (satellite) sensor
4.
5.
Belt tension sensor
6.
Seat belt buckle pre-tensioner assembly

RH
7.
Occupant classification system sensor
8.
Occupant classification system

control unit
9.
Front passenger air bag off indicator
10. Front passenger air bag module
11. Crash zone sensor
12. Air bag warning lamp
13. Spiral cable
14. Driver air bag module
15. Front LH seat belt pre-tensioner
16. LH side air bag (satellite) sensor
17. Air bag diagnosis sensor unit
18. Front LH side air bag module

(If equipped)
Revision: July 2007
SRS-10
2005 Armada
TROUBLE DIAGNOSIS
Schematic
EHS0029B
SRS
WHWA0127E
Revision: July 2007
SRS-11
2005 Armada
TROUBLE DIAGNOSIS
Wiring DiagramSRS
EHS0029C
WHWA0117E
Revision: July 2007
SRS-12
2005 Armada
TROUBLE DIAGNOSIS
SRS
WHWA0118E
Revision: July 2007
SRS-13
2005 Armada
TROUBLE DIAGNOSIS
WHWA0128E
Revision: July 2007
SRS-14
2005 Armada
TROUBLE DIAGNOSIS
SRS
WHWA0146E
Revision: July 2007
SRS-15
2005 Armada
TROUBLE DIAGNOSIS
WHWA0121E
Revision: July 2007
SRS-16
2005 Armada
TROUBLE DIAGNOSIS
SRS
WHWA0122E
Revision: July 2007
SRS-17
2005 Armada
TROUBLE DIAGNOSIS
CONSULT-II Function (AIR BAG)
EHS0029D
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
AIR BAG diagnostic mode
Description
SELF-DIAG [CURRENT]
A current Self-diagnosis result (also indicated by the number of warning lamp flashes in the Diagnosis
mode) is displayed on the CONSULT-II screen in real time. This refers to a malfunctioning part requiring repairs.
SELF-DIAG [PAST]
TROUBLE DIAG RECORD
ECU DISCRIMINATED NO.
Diagnosis results previously stored in the memory are displayed on the CONSULT-II screen. The
stored results will remain until memory erasing is executed.
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be displayed on the CONSULT-II screen.
The air bag diagnosis sensor unit for each vehicle
model is assigned with its own, individual classification number. This number will be displayed on
the CONSULT-II screen, as shown. When replacing the air bag diagnosis sensor unit, refer to the
part number for the compatibility. After installation,
replacement with a correct unit can be checked by
confirming this classification number on the CONSULT-II screen.
For NISSAN MODEL TA60, the air bag diagnosis sensor unit discriminated numbers
assigned are F62B with front side air bag modules and F629 without front side air bag modules.
ARS366
CONSULT-II Function
EHS0029E
HOW TO CHANGE SELF-DIAGNOSIS MODE WITH CONSULT-II

From User Mode to Diagnosis Mode
After selecting AIR BAG on the SELECT SYSTEM screen, User mode automatically changes to Diagnosis
mode.
SRS803
From Diagnosis Mode to User Mode

To return to User mode from Diagnosis mode, touch BACK key of CONSULT-II until SELECT SYSTEM
appears, Diagnosis mode automatically changes to User mode.
SRS804
Revision: July 2007
SRS-18
2005 Armada
TROUBLE DIAGNOSIS
HOW TO ERASE SELF-DIAGNOSIS RESULTS
SELF-DIAG [CURRENT]
A current self-diagnosis result is displayed on the CONSULT-II
screen in real time.
After the malfunction is repaired completely, no malfunction is
detected on SELF-DIAG [CURRENT].
SRS701
SELF-DIAG [PAST]
Return to the SELF-DIAG [CURRENT] CONSULT-II screen by
touching BACK key of CONSULT-II and select SELF-DIAG
[PAST] in SELECT DIAG MODE. Touch ERASE in SELFDIAG [PAST] mode.
NOTE:
If the memory of the malfunction in SELF-DIAG [PAST] is
not erased, the User mode will continue to show the system
malfunction by the operation of the warning lamp even if
the malfunction is repaired completely.
SRS702
TROUBLE DIAG RECORD

The memory of TROUBLE DIAG RECORD cannot be erased.
Self-Diagnosis Function (Without CONSULT-II)
SRS
I
EHS0029F
The reading of these results is accomplished using one of two modes User mode and Diagnosis
mode.
After a malfunction is repaired, turn the ignition switch OFF for at least one second, then back ON. Diagnosis mode returns to the User mode. At that time, the self-diagnostic result is cleared.
HOW TO CHANGE SELF-DIAGNOSIS MODE

L
SHIA0183E
Revision: July 2007
SRS-19
2005 Armada
TROUBLE DIAGNOSIS
HOW TO ERASE SELF-DIAGNOSIS RESULTS
After a malfunction is repaired, turn the ignition switch OFF for at least one second, then back ON. Diagnosis
mode returns to the User mode. At that time, the self-diagnostic result is cleared.
SRS Operation Check
EHS0029G
DIAGNOSTIC PROCEDURE 1
Checking SRS Operation Using AIR BAG Warning LampUser Mode
1.
2.
Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks.
Compare the SRS air bag warning lamp blinking pattern with the
examples.
BF-1845D
Revision: July 2007
SRS-20
2005 Armada
TROUBLE DIAGNOSIS
Warning lamp examples
AIR BAG warning lamp operation-User mode-
SRS condition
Reference item
No malfunction is detected.
No further action is necessary.
D
SHIA0011E
The system is malfunctioning and

needs to be repaired as indicated.
Go to SRS-22, "DIAGNOSTIC
PROCEDURE 2" or SRS-38,
"DIAGNOSTIC PROCEDURE 6" .
SRS
SHIA0012E
Air bag is deployed.
Seat belt buckle pre-tensioner

assembly is deployed.
Seat belt pre-tensioner is deployed.
Air bag diagnosis sensor unit is malfunctioning.
Air bag power supply circuit is malfunctioning.
SRS air bag warning lamp circuit is

malfunctioning.
Go to SRS-61, "COLLISION DIAGNOSIS" .
J
Go to SRS-44, "Trouble Diagnosis:
AIR BAG Warning Lamp Does Not
Turn Off" .
SHIA0013E
Air bag warning lamp circuit is malfunctioning.
Go to SRS-45, "Trouble Diagnosis:

AIR BAG Warning Lamp Does Not
Turn On" .
SHIA0014E
Revision: July 2007
SRS-21
2005 Armada
TROUBLE DIAGNOSIS
Trouble Diagnosis With CONSULT-II
EHS0029H
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunction might be detected
in self-diagnosis depending on control unit which carry out CAN communication.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
BBIA0369E
3.
4.
Turn ignition switch ON.

Touch START (NISSAN BASED VHCL).
BCIA0029E
5.
Touch AIR BAG.

If "AIR BAG" is not indicated, refer to GI-39, "CONSULT-II Data
Link Connector (DLC) Circuit" .
BCIA0030E
6.
Touch "SELF-DIAG [CURRENT]".
BCIA0031E
Revision: July 2007
SRS-22
2005 Armada
TROUBLE DIAGNOSIS
7.
Diagnostic code is displayed on "SELF-DIAG [CURRENT]".

A
C
WHIA0151E
If no malfunction is detected on "SELF-DIAG [CURRENT]" even

though malfunction is detected in "SRS Operation Check", refer to
SRS-31, "DIAGNOSTIC PROCEDURE 4 (CONTINUED FROM
DIAGNOSTIC PROCEDURE 2)" , to diagnose the following cases:
Self-diagnostic result "SELF-DIAG [PAST]" (previously stored in

the memory) might not be erased after repair.
The SRS system malfunctions intermittently.
G
SRS701
SRS
CONSULT-II Diagnostic Code Chart ("SELF-DIAG [CURRENT]")

Diagnostic item
When malfunction is
indicated by the AIR
BAG warning lamp in
User mode.
Low battery voltage (Less than

9V)
Go to SRS-28, "DIAGNOSTIC PROCEDURE 3" .
Self-diagnostic result SELF-DIAG

[PAST] (previously stored in the
memory) might not be erased
after repair.
Go to SRS-31, "DIAGNOSTIC PROCEDURE 4 (CONTINUED FROM

DIAGNOSTIC PROCEDURE 2)" .
Intermittent malfunction has been

detected in the past.
NO DTC IS DETECTED
DRIVER AIRBAG MODULE

[OPEN]
[B1049] or [B1054]
Driver air bag module circuit is open (including the spiral

cable).

[VB-SHORT]
[B1050] or [B1055]
Driver air bag module circuit is shorted to some power supply circuit (including the spiral cable).

[GND-SHORT]
[B1051] or [B1056]
Driver air bag module circuit is shorted to ground (including

the spiral cable).

[SHORT]
[B1052] or [B1057]
Driver air bag module circuits are shorted to each other.
Revision: July 2007
Repair order
Recheck SRS at each replacement
Explanation
1. Visually check the wiring harness

connection.
2. Replace the harness if it has visible
damage.
3. Replace driver air bag module.
4. Replace the spiral cable.
5. Replace the air bag diagnosis sensor unit.
6. Replace the related harness.
SRS-23
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
ASSIST A/B MODULE

[OPEN]
[B1065] or [B1070]
Front passenger air bag module circuit is open.
ASSIST A/B MODULE

[VB-SHORT]
[B1066] or [B1071]
Front passenger air bag module circuit is shorted to some

power supply circuit.
ASSIST A/B MODULE

[GND-SHORT]
[B1067] or [B1072]
Front passenger air bag module circuit is shorted to

ground.
ASSIST A/B MODULE

[SHORT]
[B1068] or [B1073]
Front passenger air bag module circuits are shorted to

each other.
Crash zone sensor
Repair order
connection.
damage.
3. Replace front passenger air bag
module.

connection.
CRASH ZONE SEN

[UNIT FAIL]
[B1033] or [B1034]
CRASH ZONE SEN
[COMM FAIL]
[B1035]

damage.
3. Replace the crash zone sensor.
SIDE MODULE LH
[OPEN]
[B1134]
Front LH side air bag module circuit is open.
SIDE MODULE LH
[VB-SHORT]
[B1135]
Front LH side air bag module circuit is shorted to some

SIDE MODULE LH
[GND-SHORT]
[B1136]
SIDE MODULE LH
[SHORT]
[B1137]
Front LH side air bag module circuits are shorted to each

other.
SIDE MODULE RH
[OPEN]
[B1129]
Front RH side air bag module circuit is open.
SIDE MODULE RH
[VB-SHORT]
[B1130]
Front RH side air bag module circuit is shorted to some

SIDE MODULE RH
[GND-SHORT]
[B1131]
Front RH side air bag module circuit is shorted to ground.
SIDE MODULE RH
[SHORT]
[B1132]
Front RH side air bag module circuits are shorted to each

other.
LH side air bag (satellite) sensor
Front LH side air bag module circuit is shorted to ground.

connection.
damage.
3. Replace front LH seat back assembly (front LH side air bag module).

connection.
damage.
3. Replace front RH seat back assembly (front RH side air bag module).
SATELLITE SENS LH
[UNIT FAIL]
[B1118] or [B1119]
SATELLITE SENS LH
[COMM FAIL]
[B1120]

connection.
damage.
3. Replace the LH side air bag (satellite) sensor.
Revision: July 2007
SRS-24
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
SATELLITE SENS RH
[UNIT FAIL]
[B1113] or [B1114]
SATELLITE SENS RH
[COMM FAIL]
[B1115]
Repair order
connection.
damage.
3. Replace the RH side air bag (satellite) sensor.

The circuit for front LH seat belt pre-tensioner is open.
PRE-TEN FRONT LH
[OPEN]
[B1086]
PRE-TEN FRONT LH
[VB-SHORT]
[B1087]
PRE-TEN FRONT LH
[GND-SHORT]
[B1088]
PRE-TEN FRONT LH
[SHORT]
[B1089]
The circuits for the front LH seat belt pre-tensioner are

shorted to each other.
PRE-TEN FRONT RH
[OPEN]
[B1081]
The circuit for front RH seat belt pre-tensioner is open.
PRE-TEN FRONT RH
[VB-SHORT]
[B1082]
The circuit for front RH seat belt pre-tensioner is shorted to

some power supply circuit.
PRE-TEN FRONT RH
[GND-SHORT]
[B1083]
PRE-TEN FRONT RH
[SHORT]
[B1084]
PRE-TEN2 FRONT LH
[OPEN]
[B1182]
PRE-TEN2 FRONT LH
[VB-SHORT]
[B1183]
The circuit for front LH seat belt pre-tensioner is shorted to

ground.

connections.
damage.
3. Replace front LH seat belt pre-tensioner.


ground.

connections.
SRS

damage.
3. Replace front RH seat belt pre-tensioner.
PRE-TEN2 FRONT LH
[GND-SHORT]
[B1184]
PRE-TEN2 FRONT LH
[SHORT]
[B1185]
Revision: July 2007
The circuits for the front RH seat belt pre-tensioner are

The circuit for front LH seat belt buckle pre-tensioner is
open.
shorted to some power supply circuit.
shorted to ground.
K
connections.
damage.
3. Replace front LH seat belt buckle
pre-tensioner.
The circuits for the front LH seat belt buckle pre-tensioner

are shorted to each other.
SRS-25
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
PRE-TEN2 FRONT RH
[OPEN]
[B1177]
The circuit for front RH seat belt buckle pre-tensioner is

open.
PRE-TEN2 FRONT RH
[VB-SHORT]
[B1178]

PRE-TEN2 FRONT RH
[GND-SHORT]
[B1179]

shorted to ground.
PRE-TEN2 FRONT RH
[SHORT]
[B1180]
The circuits for the front RH seat belt buckle pre-tensioner

FR CURTN MODULE LH
[OPEN]
[B1198]
The LH side front curtain air bag module circuit is open.
FR CURTN MODULE LH
[VB-SHORT]
[B1199]
The LH side front curtain air bag module circuit is shorted

to some power supply circuits.
FR CURTN MODULE LH
[GND-SHORT]
[B1200]

to ground.
FR CURTN MODULE LH
[SHORT]
[B1201]
The circuits for the LH side front curtain air bag module are
FR CURTN MODULE RH
[OPEN]
[B1193]
The RH side front curtain air bag module circuit is open.
FR CURTN MODULE RH
[VB-SHORT]
[B1194]
FR CURTN MODULE RH
[GND-SHORT]
[B1195]
FR CURTN MODULE RH
[SHORT]
[B1196]
The circuits for the RH side front curtain air bag module are
CURTAIN MODULE LH
[OPEN]
[B1150]
The LH side rear curtain air bag module circuit is open.
CURTAIN MODULE LH
[VB-SHORT]
[B1151]
The LH side rear curtain air bag module circuit is shorted to

some power supply circuits.
CURTAIN MODULE LH
[GND-SHORT]
[B1152]

ground.
CURTAIN MODULE LH
[SHORT]
[B1153]
The circuits for the LH side rear curtain air bag module are
Revision: July 2007
Repair order
connections.
damage.
3. Replace front RH seat belt buckle
pre-tensioner.

connection.
damage.
3. Replace LH side curtain air bag
module.
The RH side front curtain air bag module circuit is shorted

to ground.

connection.
damage.
3. Replace RH side curtain air bag
module.

connection.
damage.
module.
SRS-26
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
CURTAIN MODULE RH
[OPEN]
[B1145]
The RH side rear curtain air bag module circuit is open.
CURTAIN MODULE RH
[VB-SHORT]
[B1146]
CURTAIN MODULE RH
[GND-SHORT]
[B1147]
The RH side rear curtain air bag module circuit is shorted

to ground.
CURTAIN MODULE RH
[SHORT]
[B1148]
The circuits for the RH side rear curtain air bag module are


damage.
module.

connection.
Occupant classification system is malfunctioning.
1. Replace RH front seat cushion/

occupant classification system control unit assembly.
Communication between the occupant classification system control unit and air bag diagnosis sensor unit is interrupted.

connection.
OCCUPANT SENS C/U

[COMM FAIL]
[B1022]

connection.
CONTROL UNIT
[B1XXX]
OCCUPANT SENS C/U
[UNIT FAIL]
[B1017], [B1020] or [B1021]
Repair order

damage.
SRS

OCCUPANT SENS
[UNIT FAIL]
[B1018]
Occupant classification sensor is malfunctioning.

Belt tension sensor is malfunctioning.

connection.
damage.
BELT TENSION SENS

[UNIT FAIL]
[B1019]
Front passenger air bag off indicator is malfunctioning.

connection.
damage.
PASS A/B INDCTR CKT

[B1023]
3. Replace front passenger air bag off

indicator.
Revision: July 2007
3. Replace RH front seat belt assembly.

FRONTAL COLLISION
DETECTION
[B1209]
Driver and front passenger air bag modules are deployed.
SRS-27
1. Refer to SRS-61, "COLLISION

DIAGNOSIS" .
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
Repair order
SIDE COLLISION
DETECTION
[B1210]
Side or curtain air bag modules are deployed.

DIAGNOSIS" .
ROLLOVER DETECTION
[B1211]
Curtain air bag module and seat belt pre-tensioner are

deployed.

DIAGNOSIS" .
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is
eliminated using air bag warning lamp or CONSULT-II each time repair is finished. If malfunction is still
observed, proceed to the next step. When malfunction is eliminated, further repair work is not required.
Final Check of SRS Using CONSULT-IIDiagnosis Mode
CAUTION:
1. After repairing SRS, connect both battery cables.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. Turn ignition switch ON.
BBIA0369E
4.
BCIA0029E
5.
Touch AIR BAG.

BCIA0030E
Revision: July 2007
SRS-28
2005 Armada
TROUBLE DIAGNOSIS
6.
Touch SELF-DIAG [CURRENT].

A
C
BCIA0031E
7.
If no malfunction is detected on SELF-DIAG [CURRENT],

repair of SRS is completed. Go to step 8.
If any malfunction is detected on SELF-DIAG [CURRENT], the
malfunctioning part is not repaired completely or another malfunctioning part is detected. Go to SRS-22, "DIAGNOSTIC
PROCEDURE 2" , and repair malfunctioning part completely.
G
SRS701
8.
Touch ERASE.
NOTE:
Touch ERASE to clear the memory of the malfunction
(SELF-DIAG [PAST]).
If the memory of the malfunction in SELF-DIAG [PAST] is not
erased, the User mode shows the system malfunction by the
operation of the warning lamp even if the malfunction is repaired
completely.
SRS
WHIA0152E
9.
Touch BACK key of CONSULT-II to SELECT DIAG MODE

screen. Touch SELF-DIAG [PAST].
BCIA0031E
10. Check that no malfunction is detected on SELF-DIAG [PAST].

11. Touch BACK key of CONSULT-II until SELECT SYSTEM
appears in order to return to User mode from Diagnosis mode.
12. Turn ignition switch OFF then turn off and disconnect CONSULT-II.
13. Go to SRS-20, "DIAGNOSTIC PROCEDURE 1" .
SRS702
Revision: July 2007
SRS-29
2005 Armada
TROUBLE DIAGNOSIS
Revision: July 2007
SRS-30
2005 Armada
TROUBLE DIAGNOSIS
DIAGNOSTIC PROCEDURE 4 (CONTINUED FROM DIAGNOSTIC PROCEDURE 2)
Check SRS Repair History
1. CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS.

Have any previous repairs been made to the SRS?
Yes
>> Self-diagnostic result SELF-DIAG [PAST] (previously stored in the memory) might not be erased
after repair. Go to SRS-28, "DIAGNOSTIC PROCEDURE 3" .
No
>> Go to SRS-22, "DIAGNOSTIC PROCEDURE 2" .
Check SRS Intermittent Malfunction Using CONSULT-IIDiagnosis Mode
CAUTION:
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
SRS
I
BBIA0369E
3.
4.
Turn ignition switch ON.

M
BCIA0029E
5.
Touch AIR BAG.

BCIA0030E
Revision: July 2007
SRS-31
2005 Armada
TROUBLE DIAGNOSIS
6.
Touch SELF-DIAG [PAST].
BCIA0031E
7.
If diagnostic codes are displayed on SELF-DIAG [PAST], go to

step 10.
WHIA0152E
If no malfunction is detected on SELF-DIAG [PAST], touch

BACK and go back to SELECT DIAG MODE.
SRS702
8.
Touch TROUBLE DIAG RECORD.

NOTE:
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be displayed.
BCIA0031E
9. Diagnostic code is displayed on TROUBLE DIAG RECORD.

10. Touch PRINT.
11. Compare diagnostic codes to SRS-33, "CONSULT-II Diagnostic
Code Chart ("SELF-DIAG [PAST]" or "TROUBLE DIAG
RECORD")" .
12. Touch BACK key of CONSULT-II until SELECT SYSTEM
appears.
13. Turn ignition switch OFF, then turn off and disconnect CONSULT-II, and both battery cables.
WHIA0153E
Revision: July 2007
SRS-32
2005 Armada
TROUBLE DIAGNOSIS
14. Repair the system as outlined by the Repair order in Intermittent Malfunction Diagnostic Code Chart,
that corresponds to the self-diagnostic result. For replacement procedure of component parts, refer to the
Removal and Installation procedure for the appropriate component.
15. Go to SRS-28, "DIAGNOSTIC PROCEDURE 3" , for final checking.
CONSULT-II Diagnostic Code Chart ("SELF-DIAG [PAST]" or "TROUBLE DIAG RECORD")

Diagnostic item
Low battery voltage (Less than

9V)
Self-diagnostic result SELF-DIAG

[PAST] (previously stored in the
memory) might not be erased
after repair.
Go to SRS-31, "DIAGNOSTIC PROCEDURE 4 (CONTINUED FROM

DIAGNOSTIC PROCEDURE 2)" .
Intermittent malfunction has been

detected in the past.
NO DTC IS DETECTED

[OPEN]
[B1049] or [B1054]
Driver air bag module circuit is open (including the spiral

cable).

[VB-SHORT]
[B1050] or [B1055]
Driver air bag module circuit is shorted to some power supply circuit (including the spiral cable).

[GND-SHORT]
[B1051] or [B1056]
Driver air bag module circuit is shorted to ground (including

the spiral cable).

[SHORT]
[B1052] or [B1057]
Driver air bag module circuits are shorted to each other.
ASSIST A/B MODULE

[OPEN]
[B1065] or [B1070]
ASSIST A/B MODULE

[VB-SHORT]
[B1066] or [B1071]
ASSIST A/B MODULE

[GND-SHORT]
[B1067] or [B1072]
ASSIST A/B MODULE

[SHORT]
[B1068] or [B1073]
Front passenger air bag module circuits are shorted to

each other.
Crash zone sensor

connection.
damage.
3. Replace driver air bag module.
4. Replace the spiral cable.

SRS
I
Front passenger air bag module circuit is open.
Front passenger air bag module circuit is shorted to some

Front passenger air bag module circuit is shorted to
ground.

connection.

damage.
3. Replace front passenger air bag
module.

M
connection.
CRASH ZONE SEN

[UNIT FAIL]
[B1033] or [B1034]
CRASH ZONE SEN
[COMM FAIL]
[B1035]

damage.
3. Replace the crash zone sensor.
Revision: July 2007
Repair order
Explanation
When malfunction is
indicated by the AIR
BAG warning lamp in
User mode.
SRS-33
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
SIDE MODULE LH
[OPEN]
[B1134]
Front LH side air bag module circuit is open.
SIDE MODULE LH
[VB-SHORT]
[B1135]
Front LH side air bag module circuit is shorted to some

SIDE MODULE LH
[GND-SHORT]
[B1136]
Front LH side air bag module circuit is shorted to ground.
SIDE MODULE LH
[SHORT]
[B1137]
Front LH side air bag module circuits are shorted to each

other.
SIDE MODULE RH
[OPEN]
[B1129]
Front RH side air bag module circuit is open.
SIDE MODULE RH
[VB-SHORT]
[B1130]
Front RH side air bag module circuit is shorted to some

SIDE MODULE RH
[GND-SHORT]
[B1131]
Front RH side air bag module circuit is shorted to ground.
SIDE MODULE RH
[SHORT]
[B1132]
Front RH side air bag module circuits are shorted to each

other.
LH side air bag (satellite) sensor
Repair order
connection.
damage.
3. Replace front LH seat back assembly (front LH side air bag module).

connection.
damage.
3. Replace front RH seat back assembly (front RH side air bag module).
SATELLITE SENS LH
[UNIT FAIL]
[B1118] or [B1119]
SATELLITE SENS LH
[COMM FAIL]
[B1120]

connection.
damage.
3. Replace the LH side air bag (satellite) sensor.
SATELLITE SENS RH
[UNIT FAIL]
[B1113] or [B1114]
SATELLITE SENS RH
[COMM FAIL]
[B1115]

connection.
damage.
3. Replace the RH side air bag (satellite) sensor.
PRE-TEN FRONT LH
[OPEN]
[B1086]
The circuit for front LH seat belt pre-tensioner is open.
PRE-TEN FRONT LH
[VB-SHORT]
[B1087]

PRE-TEN FRONT LH
[GND-SHORT]
[B1088]

ground.
PRE-TEN FRONT LH
[SHORT]
[B1089]
The circuits for the front LH seat belt pre-tensioner are

Revision: July 2007

connections.
damage.
3. Replace front LH seat belt pre-tensioner.
SRS-34
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
PRE-TEN FRONT RH
[OPEN]
[B1081]
PRE-TEN FRONT RH
[VB-SHORT]
[B1082]
PRE-TEN FRONT RH
[GND-SHORT]
[B1083]

ground.
PRE-TEN FRONT RH
[SHORT]
[B1084]
The circuits for the front RH seat belt pre-tensioner are

PRE-TEN2 FRONT LH
[OPEN]
[B1182]

open.
PRE-TEN2 FRONT LH
[VB-SHORT]
[B1183]

PRE-TEN2 FRONT LH
[GND-SHORT]
[B1184]

shorted to ground.
PRE-TEN2 FRONT LH
[SHORT]
[B1185]
The circuits for the front LH seat belt buckle pre-tensioner

PRE-TEN2 FRONT RH
[OPEN]
[B1177]

open.
PRE-TEN2 FRONT RH
[VB-SHORT]
[B1178]
PRE-TEN2 FRONT RH
[GND-SHORT]
[B1179]
PRE-TEN2 FRONT RH
[SHORT]
[B1180]
FR CURTN MODULE LH
[OPEN]
[B1198]
The LH side front curtain air bag module circuit is open.
FR CURTN MODULE LH
[VB-SHORT]
[B1199]

FR CURTN MODULE LH
[GND-SHORT]
[B1200]

to ground.
FR CURTN MODULE LH
[SHORT]
[B1201]
The circuits for the LH side front curtain air bag module are
Revision: July 2007
The circuit for front RH seat belt pre-tensioner is open.

Repair order

connections.
damage.
3. Replace front RH seat belt pre-tensioner.


connections.
damage.
3. Replace front LH seat belt buckle

pre-tensioner.

shorted to ground.
SRS
connections.
3. Replace front RH seat belt buckle

pre-tensioner.
The circuits for the front RH seat belt buckle pre-tensioner

L
connection.
damage.
module.
SRS-35

damage.
2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
FR CURTN MODULE RH
[OPEN]
[B1193]
The RH side front curtain air bag module circuit is open.
FR CURTN MODULE RH
[VB-SHORT]
[B1194]

FR CURTN MODULE RH
[GND-SHORT]
[B1195]

to ground.
FR CURTN MODULE RH
[SHORT]
[B1196]
The circuits for the RH side front curtain air bag module are
CURTAIN MODULE LH
[OPEN]
[B1150]
The LH side rear curtain air bag module circuit is open.
CURTAIN MODULE LH
[VB-SHORT]
[B1151]

some power supply circuits.
CURTAIN MODULE LH
[GND-SHORT]
[B1152]

ground.
CURTAIN MODULE LH
[SHORT]
[B1153]
The circuits for the LH side rear curtain air bag module are
CURTAIN MODULE RH
[OPEN]
[B1145]
The RH side rear curtain air bag module circuit is open.
CURTAIN MODULE RH
[VB-SHORT]
[B1146]
CURTAIN MODULE RH
[GND-SHORT]
[B1147]
CURTAIN MODULE RH
[SHORT]
[B1148]
The circuits for the RH side rear curtain air bag module are

connection.
damage.
module.

connection.
damage.
module.

to ground.

connection.
damage.
module.
CONTROL UNIT
[B1XXX]
OCCUPANT SENS C/U
[UNIT FAIL]
[B1017], [B1020] or [B1021]
Repair order

connection.
Occupant classification system is malfunctioning.

Communication between the occupant classification system control unit and air bag diagnosis sensor unit is interrupted.

connection.
OCCUPANT SENS C/U

[COMM FAIL]
[B1022]

damage.
OCCUPANT SENS
[UNIT FAIL]
[B1018]
Revision: July 2007
Occupant classification sensor is malfunctioning.
SRS-36

2005 Armada
TROUBLE DIAGNOSIS
Diagnostic item
Explanation
Belt tension sensor is malfunctioning.
Repair order
connection.
damage.
BELT TENSION SENS

[UNIT FAIL]
[B1019]
3. Replace RH front seat belt assembly.

Front passenger air bag off indicator is malfunctioning.

connection.
damage.
PASS A/B INDCTR CKT

[B1023]
3. Replace front passenger air bag off

indicator.

FRONTAL COLLISION
DETECTION
[B1209]
Driver and front passenger air bag modules are deployed.

DIAGNOSIS" .
SIDE COLLISION
DETECTION
[B1210]
Side or curtain air bag modules are deployed.

DIAGNOSIS" .
ROLLOVER DETECTION
[B1211]
Curtain air bag module and seat belt pre-tensioner are

deployed.

DIAGNOSIS" .
SRS
Revision: July 2007
SRS-37
2005 Armada
TROUBLE DIAGNOSIS
Trouble Diagnosis Without CONSULT-II
EHS0029I
Inspect SRS Malfunction Using "AIR BAG" Warning LampDiagnosis Mode
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
2. After AIR BAG warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3. Wait more than 3 seconds.
4. Repeat steps 1 to 3 two more times (3 times total).
SRS is now in Diagnosis mode.
"AIR BAG" warning lamp operates in Diagnosis mode as follows:
Revision: July 2007
SRS-38
2005 Armada
TROUBLE DIAGNOSIS
WARNING LAMP FLASH CODE CHART
A
SHIA0026E
G
WHIA0197E
SRS
K
WHIA0198E
WHIA0199E
Revision: July 2007
SRS-39
2005 Armada
TROUBLE DIAGNOSIS
WHIA0200E
WHIA0201E
WHIA0217E
WHIA0202E
Revision: July 2007
SRS-40
2005 Armada
TROUBLE DIAGNOSIS
C
WHIA0218E
G
WHIA0203E
SRS
K
WHIA0204E
WHIA0205E
Revision: July 2007
SRS-41
2005 Armada
TROUBLE DIAGNOSIS
WHIA0206E
WHIA0207E
WHIA0208E
WHIA0209E
Revision: July 2007
SRS-42
2005 Armada
TROUBLE DIAGNOSIS
C
WHIA0210E
G
WHIA0211E
SRS
K
WHIA0212E
Revision: July 2007
SRS-43
2005 Armada
TROUBLE DIAGNOSIS
Trouble Diagnosis: AIR BAG Warning Lamp Does Not Turn Off
EHS0029J
1. CHECK CONDITION OF AIR BAG MODULE

Inspect for any deployed air bag modules or seat belt pre-tensioners.
Are any air bag modules or seat belt pre-tensioners deployed?
Yes
>> Refer to SRS-61, "COLLISION DIAGNOSIS" .
No
>> GO TO 2.
2. CHECK THE AIR BAG FUSE

Check 10A fuse [No. 13, located in the fuse block (J/B)].
Refer to PG-4, "POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3. CHECK AIR BAG FUSE AGAIN

Replace 10A fuse [No. 13, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
Yes
>> Repair main harness.
No
>> Inspection End.
4. CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Connect CONSULT-II and touch START.
Is AIR BAG displayed on CONSULT-II?
Yes
>> GO TO 5.
No
>> Visually inspect the air bag diagnosis sensor unit harness connections. If the connections are OK, replace
the air bag diagnosis sensor unit. Refer to SRS-59,
"Removal and Installation" .
BCIA0030E
5. CHECK HARNESS CONNECTION

Check for loose connections between the combination meter and the air bag diagnosis sensor unit.
OK or NG
OK
>> Replace air bag diagnosis sensor unit. Refer to SRS-59, "Removal and Installation" .
NG
>> Properly connect the combination meter and air bag diagnosis sensor unit harness connectors. If
AIR BAG warning lamp still does not turn off, replace the wiring harness.
Revision: July 2007
SRS-44
2005 Armada
TROUBLE DIAGNOSIS
Trouble Diagnosis: AIR BAG Warning Lamp Does Not Turn On
EHS0029K
1. CHECK METER FUSE

B
Check the 10A fuse [No. 14, located in the fuse block (J/B)].
Refer to PG-4, "POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2. CHECK METER FUSE AGAIN
Replace 10A fuse [No. 14, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
Yes
>> Repair the related harness.
No
>> Inspection End.
3. CHECK HARNESS CONNECTION BETWEEN AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINA-
TION METER
Disconnect the air bag diagnosis sensor unit harness connectors and turn ignition switch ON.
Does AIR BAG warning lamp turn on?
Yes
>> Replace the air bag diagnosis sensor unit. Refer to SRS-59, "Removal and Installation" .
No
>> Check the combination meter ground circuits.
SRS
Revision: July 2007
SRS-45
2005 Armada
DRIVER AIR BAG MODULE

Removal and Installation
PFP:K8510
EHS0029L
WHIA0159E
1.
Horn harness
2.
Steering wheel hook
3.
Inflator harness
4.
Side lids RH/LH
5.
6.
Steering wheel
REMOVAL
CAUTION:
Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a

driver air bag direct-connect harness connector is damaged, the spiral cable must be replaced.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.
When servicing the SRS, do not work from directly in front of air bag module.
1. Remove the left and right side bolts.
2. Lift the driver air bag module from the steering wheel.
3. Disconnect the air bag harness and horn connectors, then remove the driver air bag module.
For removal/installation of the direct-connect SRS connectors, refer to SRS-7, "Direct-connect SRS
Component Connectors" .
CAUTION:
Always place air bag module with pad side facing upward.
Do not insert any foreign objects (screwdriver, etc.) into air

bag module or harness connectors.
Do not disassemble air bag module.
Do not use old bolts after removal; replace with new bolts.
Do not expose the air bag module to temperatures exceeding 90C (194F).
LHIA0052E
Revision: July 2007
SRS-46
2005 Armada
Replace the air bag module if it has been dropped or sustained an impact.
Do not allow oil, grease or water to come in contact with the
air bag module.
C
SBF814E
INSTALLATION
To install, reverse the removal procedure.
If driver air bag module is being replaced due to deployment, spiral cable must also be replaced. Refer to
SRS-48, "SPIRAL CABLE" .
For removal/installation of the direct-connect SRS connectors, refer to SRS-7, "Direct-connect SRS Component Connectors" .
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRS-20, "SRS Operation Check" .
SRS
Revision: July 2007
SRS-47
2005 Armada
SPIRAL CABLE
SPIRAL CABLE
PFP:25554
EHS0029M
WHIA0233E
1.
Steering wheel
2.
Lighting and turn signal switch
3.
Wiper and washer switch
4.
Spiral cable
5.
Driver air bag module connector
6.
Column cover upper
7.
Column assembly
8.
Column cover lower
9.
Screw (Do not remove)
10. Screw
REMOVAL
CAUTION:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.
1. Set the front wheels in the straight-ahead position.
2. Remove driver air bag module. Refer to SRS-46, "DRIVER AIR BAG MODULE" .
3. Remove the steering wheel center nut.
4. Remove the steering wheel using Tool.
Tool number:
5.
A: J-1859A
B: J-42578
Remove the column cover upper and lower.
WHIA0124E
Revision: July 2007
SRS-48
2005 Armada
SPIRAL CABLE
6.
Remove wiper washer switch connector, then pinch the tabs at

wiper and washer switch base and slide switch away from steering column to remove.
C
LHIA0034E
7.
While pressing tabs, pull lighting and turn signal switch toward
driver door and disconnect from base.
E
G
LHIA0035E
8.
SRS
Remove the screws, release the clip, and remove the spiral
cable.
CAUTION:
Do not disassemble spiral cable.
Do not apply lubricant to the spiral cable.
K
LHIA0036E
9.
Remove the spiral cable connectors.

CAUTION:
With the steering linkage disconnected, the spiral cable
may snap by turning the steering wheel beyond the limited
number of turns. The spiral cable can be turned counterclockwise about 2.5 turns from the right end position.
SHIA0193E
Revision: July 2007
SRS-49
2005 Armada
SPIRAL CABLE
INSTALLATION
Installation is in the reverse order of removal.
Align spiral cable correctly when installing steering wheel. Make

sure that the spiral cable is in the neutral position. The neutral
position is detected by turning left 2.6 revolutions from the right
end position and ending with the knob at the top.
If equipped with VDC, refer to BRC-61, "Adjustment of Steering

Angle Sensor Neutral Position"
for steering angle sensor
adjustment.
After the work is completed, perform self-diagnosis to make sure

no malfunction is detected. Refer to SRS-20, "SRS Operation
Check" .
CAUTION:
The spiral cable may snap due to steering operation if the

cable is not installed in the correct position.
With the steering linkage disconnected, the cable may snap

by turning the steering wheel beyond the limited number of
turns. The spiral cable can be turned counterclockwise
about 2.5 turns from the right end position.
Steering wheel center nut
WGIA0038E
: 34 Nm (3.5 kg-m, 25 ft-lb)
PHIA0275E
Revision: July 2007
SRS-50
2005 Armada
FRONT PASSENGER AIR BAG MODULE

PFP:K8515
A
EHS0029N
The passenger air bag module originally installed in the vehicle uses direct-connect style harness connectors.
Service replacement passenger air bag modules use tab-locking style harness connectors. If the passenger
air bag module is replaced or if the direct-connect harness connectors are damaged, the vehicle wiring harness must be modified to allow connection of the service replacement passenger air bag module. Refer to
SRS-52, "WIRING HARNESS MODIFICATION" for wiring harness modification procedure.
REMOVAL
CAUTION:
Do not attempt to repair or replace damaged direct-connect front passenger air bag module con- D
nectors. If a direct-connect harness connector is damaged, the front passenger air bag must be
replaced and the wiring harness modified.
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least E
3 minutes.
Always work from the side of or under front passenger air bag module.
1. Remove the glove box. Refer to IP-13, "LOWER INSTRUMENT PANEL RH AND GLOVE BOX" .
F
2. Remove 2 nuts (through glove box opening) retaining front passenger air bag module to instrument panel crossmember.
3. Disconnect the air bag module electrical connectors.
G
SRS
4. Remove the instrument panel assembly from the vehicle. Refer
to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
5. Remove front passenger air bag module nuts and remove air
I
bag module from the instrument panel assembly.
WHIA0110E
CAUTION:
When servicing the SRS, do not work from directly in front
of air bag module.
Always place front passenger air bag module with caution

label side facing upward.
Do not insert any foreign objects (screwdriver, etc.) into air

bag module or harness connectors.
Do not use old nuts after removal; replace with new nuts.
Do not expose the front passenger air bag module to temperatures exceeding 90C (194F).
M
WHIA0111E
Replace the air bag module if it has been dropped or sustained an impact.
air bag module.
SBF814E
INSTALLATION
Original Passenger Air Bag Module
Revision: July 2007
SRS-51
2005 Armada

CAUTION:
After the work is completed, perform self-diagnosis to check that no malfunction is detected.
Refer to SRS-20, "SRS Operation Check" .
Service Replacement Passenger Air Bag Module

1.
Install the front passenger air bag module to the instrument

panel pad assembly.
WHIA0110E
2.
3.
Install the instrument panel assembly. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
Connect the front passenger air bag module harness connector to yellow 4-pin service replacement air
bag connector and fasten connector to mounting bracket.
CAUTION:
WIRING HARNESS MODIFICATION

The passenger air bag module originally installed in the vehicle uses direct-connect style harness connectors.
Service replacement passenger air bag modules use tab-locking style harness connectors. If the passenger
air bag module is replaced or if the direct-connect harness connectors are damaged, the vehicle wiring harness must be modified to allow connection of the service replacement passenger air bag module.
NOTE:
The wiring harness modification is to be performed only if the vehicle is equipped with the original passenger
air bag which uses direct-connect harness connectors. If the passenger air bag is to be replaced in a vehicle
that has already had the service replacement passenger air bag installed, the wiring harness modification is
not required.
CAUTION:
Do not attempt to repair or replace damaged direct-connect front passenger air bag module connectors. If a direct-connect harness connector is damaged, the front passenger air bag must be
replaced and the wiring harness modified.
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
1. Locate the yellow and orange direct-connect passenger air bag module harness connectors.
2. Use wire cutters to cut back both previously used direct-connect passenger air bag module harness connectors from the vehicle wiring harness approximately 50 mm (1.9 in) from the connectors.
3. Remove approximately 150 mm (5.9 in) of the vehicle harness covering from the cut end.
Revision: July 2007
SRS-52
2005 Armada

4.
Slide a piece of dual-wall heat shrink tubing (provided in the passenger air bag service kit) onto each wire of the previously used
vehicle wiring harness.
C
LHIA0017E
5.
Fold each wire back and insert into the end of the heat shrink
tubing so that the end of the wire is approximately centered in
the heat shrink tubing.
G
WHIA0062E
6.
7.
8.
SRS
Use a heat gun to shrink the heat shrink tubing and seal the wire.
Use electrical tape to secure the modified circuits to the outside of the wiring harness.
Locate the front passenger air bag service replacement connector that is taped back to the main harness. Unwrap the tape to
access the yellow service replacement connector and remove
the dust cover from the connector.
WHIA0118E
Revision: July 2007
SRS-53
2005 Armada
SIDE CURTAIN AIR BAG MODULE

PFP:985P0
EHS0029O
LHIA0079E
REMOVAL
CAUTION:
Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a

direct-connect harness connector is damaged, the harness must be replaced.
Before servicing the SRS, turn the ignition switch off, disconnect both battery cables and wait at
least 3 minutes.
1. Remove headlining. Refer to EI-35, "HEADLINING" .
2. Disconnect front and rear side curtain air bag module connectors.
For removal/installation of the direct-connect SRS connectors, refer to SRS-7, "Direct-connect SRS
Component Connectors" .
3. Remove the bolts in order starting at the front or rear, and remove the side curtain air bag module.
CAUTION:
Do not insert any foreign objects (screwdriver, etc.) into air bag module or harness connectors.
Do not expose the air bag module to temperatures exceeding 90C (194F).
Replace side curtain air bag module if it has been dropped

or sustained an impact.

air bag module.
SBF814E
INSTALLATION
Revision: July 2007
SRS-54
2005 Armada
After replacement of side curtain air bag module, perform self-diagnosis to check that no malfunction is
detected. Refer to SRS-20, "SRS Operation Check" .
SRS
Revision: July 2007
SRS-55
2005 Armada
CRASH ZONE SENSOR

CRASH ZONE SENSOR
PFP:98531
EHS0029P
REMOVAL
CAUTION:
least 3 minutes.
1. Remove front grille. Refer to EI-18, "FRONT GRILLE" .
2. Disconnect the crash zone sensor harness connector.
3. Remove crash zone sensor nuts.
LHIA0056E
CAUTION:
Replace crash zone sensor if it has been dropped or sustained an impact.
Do not disassemble crash zone sensor.
INSTALLATION
After the work is complete, perform self-diagnosis to check that no malfunction is detected. Refer to SRS20, "SRS Operation Check" .
Revision: July 2007
SRS-56
2005 Armada
SIDE AIR BAG (SATELLITE) SENSOR

SIDE AIR BAG (SATELLITE) SENSOR
PFP:98830
A
EHS0029Q
REMOVAL
CAUTION:
least 3 minutes.
1. Remove seat belt pre-tensioner. Refer to SB-3, "Removal and
Installation of Front Seat Belt" .
2. Remove side air bag (satellite) sensor nuts.
3. Disconnect the side air bag (satellite) sensor harness connector.
LHIA0057E
CAUTION:
Do not use old nuts after removal; replace with new nuts.
G
Check side air bag (satellite) sensor to ensure it is free of deformities, dents, cracks or rust. If it
shows any visible signs of damage, replace it with new one.
Do not disassemble side air bag (satellite) sensor.

SRS
Replace side air bag (satellite) sensor if it has been dropped or sustained an impact.
INSTALLATION
Revision: July 2007
SRS-57
2005 Armada
FRONT SEAT BELT PRE-TENSIONER

FRONT SEAT BELT PRE-TENSIONER
PFP:86884
EHS0029R
For removal and installation procedures for seat belt and seat belt buckle pre-tensioners, refer to SB-3,
"Removal and Installation of Front Seat Belt" .
Revision: July 2007
SRS-58
2005 Armada
DIAGNOSIS SENSOR UNIT

DIAGNOSIS SENSOR UNIT
PFP:28556
A
EHS0029S
REMOVAL
B
G
LHIA0053E
CAUTION:
Before servicing the SRS, turn the ignition switch off, disconnect both battery cables and wait at SRS
least 3 minutes.
1. Disconnect the harness connectors for each air bag module and seat belt pre-tensioner.
I
2. Remove center console. Refer to IP-14, "CENTER CONSOLE" .
3. Disconnect diagnosis sensor unit harness connectors.
4. Remove fixing bolts from the diagnosis sensor unit.
J
CAUTION:
Do not use old bolts; replace with new bolts.
Check diagnosis sensor unit bracket to ensure it is free of deformities, dents, cracks or rust. If it
K
shows any visible signs of damage, replace with new one.
Replace diagnosis sensor unit if it has been dropped or sustained an impact.

L
INSTALLATION
CAUTION:
The diagnosis sensor unit must always be installed with the arrow mark "" pointing toward the
front of the vehicle for proper operation.
ECU DISCRIMINATED NO.

After replacing the diagnosis sensor unit, confirm that the diagnosis sensor unit identification is correct for the
vehicle as equipped. Refer to .SRS-18, "CONSULT-II Function" .
Revision: July 2007
SRS-59
2005 Armada
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
PFP:98852
EHS0029T
The occupant classification control unit, occupant classification (pressure) sensor, and bladder are an integral
part of the front passenger seat cushion and are replaced as an assembly. Refer to SE-89, "FRONT SEAT" to
remove the seat, and SE-94, "SEAT CUSHION TRIM AND PAD (DRIVER) OR SEAT CUSHION ASSEMBLY
(PASSENGER)" to replace the seat cushion.
Revision: July 2007
SRS-60
2005 Armada
COLLISION DIAGNOSIS
COLLISION DIAGNOSIS
For Frontal Collision
PFP:00015
A
EHS0029U
Check the SRS components using the following table.
SRS INSPECTION (FOR FRONTAL COLLISION)

Part
SRS is activated
If the driver air bag
has deployed:
REPLACE
Install with new fasteners.
SRS is NOT activated

If the driver air bag has NOT been activated:
1. Remove driver air bag module. Check harness cover and connectors for damage,
terminals for deformities, and harness for binding.
2. Install driver air bag module into the steering wheel to check fit and alignment with
the wheel.
3. If no damage is found, reinstall with new fasteners.
4. If damagedREPLACE. Install driver air bag modules with new fasteners.

Front passenger air
bag module
If the front passenger

air bag has deployed:
REPLACE
If the front passenger air bag has NOT been activated:

1. Remove front passenger air bag module. Check harness cover and connectors for
damage, terminals for deformities, and harness for binding.
2. Install front passenger air bag module into the instrument panel to check fit with the
instrument panel.

4. If damagedREPLACE. Install front passenger air bag modules with new fasteners.
Crash zone sensor
If any of the front air

bags or seat belt pretensioners* have
been activated:
REPLACE the crash
zone sensor and
bracket with new fasteners.
*: Confirm seat belt
pre-tensioner activation using CONSULTII only.
Seat belt pre-tensioner assemblies

(All applicable locations: buckle, reel, lap
outer)
If either the driver or

passenger seat belt
pre-tensioner* has
been activated:
REPLACE all seat
belt pre-tensioner
assemblies with new
fasteners.
If the front air bags or seat belt pre-tensioners have NOT been activated:
1. Remove the crash zone sensor. Check harness connectors for damage, terminals
for deformities, and harness for binding.
Revision: July 2007
If any of the SRS

components have
been activated:
REPLACE the diagnosis sensor unit.
2. Check for visible signs of damage (dents, cracks, deformation) of the crash zone
sensor and bracket.
3. Install the crash zone sensor to check fit.

5. If damagedREPLACE the crash zone sensor and bracket with new fasteners.
If the pre-tensioners have NOT been activated:
1. Remove seat belt pre-tensioners.

Check harness cover and connectors for damage, terminals for deformities, and
harness for binding.
2. Check belts for damage and anchors for loose mounting.
3. Check retractor for smooth operation.
4. Check seat belt adjuster for damage.
5. Check for deformities of the center pillar inner.
6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner
assembly.
7. If no damage is found, reinstall seat belt pre-tensioner assembly.
8. If damagedREPLACE. Install the seat belt pre-tensioners with new fasteners.
Diagnosis sensor unit
SRS
If none of the SRS components have been activated:

1. Check case for dents, cracks or deformities.
2. Check connectors for damage, and terminals for deformities.
4. If damagedREPLACE. Install diagnosis sensor unit with new fasteners.
SRS-61
2005 Armada
COLLISION DIAGNOSIS
Part
Steering wheel
SRS is activated
1. Visually check steering wheel for deformities.

2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.
3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4. Check steering wheel for excessive free play.
5. If no damage is found, reinstall.
6. If damagedREPLACE.
Spiral cable
If the driver front air

bag has deployed:
REPLACE the spiral
cable.
If the driver front air bag has not deployed:

1. Visually check spiral cable and combination switch for damage.
2. Check connectors and protective tape for damage.
3. Check steering wheel for noise, binding or heavy operation.
4. If no damage is found, reinstall.
5. If damagedREPLACE.
Occupant classification system (Passenger seat)
1. Remove passenger seat.

2. Check control unit case for dents, cracks of deformities.
3. Check connectors and pressure sensor tube for damage, and terminals for deformities.
4. Check seat frame and cushion pan for dents or deformities.
5. If no damage is found, reinstall seat with new fasteners.
6. If damaged REPLACE seat cushion assembly with new fasteners.
Harness and connectors
1. Check connectors for poor connection, damage, and terminals for deformities.
2. Check harness for binding, chafing, cuts, or deformities.
3. If no damage is found, reinstall the harness and connectors.
4. If damagedREPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.
Instrument panel
If the passenger front

REPLACE the instrument panel assembly.
If the passenger front air bag has NOT deployed:

1. Visually check instrument panel for damage.
2. If no damage is found, reinstall the instrument panel.
3. If damagedREPLACE the instrument panel.
For Side and Rollover Collision
EHS0029V
Check the SRS components using the following table.
WHEN SRS IS ACTIVATED IN THE SIDE OR ROLLOVER COLLISION

1.
2.
3.
Replace the following components:

Front seat back assembly (on the side on which side air bag is activated)
(LH or RH) side air bag (satellite) sensor (on the side on which side air bag is activated)
Check the SRS components and the related parts using the following table.
Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).
Conduct self-diagnosis using CONSULT-II and AIR BAG warning lamp. Refer to SRS-20, "SRS Operation Check" for details. Ensure entire SRS operates properly.
WHEN SRS IS NOT ACTIVATED IN THE SIDE OR ROLLOVER COLLISION

1.
2.
Check the SRS components and the related parts using the following table.
If the front seat back assembly is damaged, the front seat back assembly must be replaced.
Conduct self-diagnosis using CONSULT-II and AIR BAG warning lamp. Refer to SRS-20, "SRS Operation Check" for details. Ensure entire SRS operates properly.
Revision: July 2007
SRS-62
2005 Armada
COLLISION DIAGNOSIS
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
Part
LH side curtain air
bag module
SRS is activated
If the LH side curtain
REPLACE the LH
side curtain air bag
module. (Repair the
center pillar inner, etc.
before installing new
one if damaged.)

If the LH side curtain air bag has NOT deployed:
1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on
the collision side.
2. If damagedRemove the LH side curtain air bag module.

3. Check for visible signs of damaged (tears etc.) of the LH side curtain air bag module.
4. Check harness and connectors for damage, and terminals for deformities.
5. If no damage is found, reinstall the LH side curtain air bag module with new fasteners.
6. If damagedREPLACE the LH side curtain air bag module with new fasteners.
RH side curtain air
bag module
If the RH side curtain

REPLACE the RH
side curtain air bag
module. (Repair the
center pillar inner, etc.
one if damaged.)
If the RH side curtain air bag has NOT deployed:

1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on
the collision side.
2. If damagedRemove the RH side curtain air bag module.

3. Check for visible signs of damaged (tears etc.) of the RH side curtain air bag module.
5. If no damage is found, reinstall the RH side curtain air bag module with new fasteners.
6. If damagedREPLACE the RH side curtain air bag module with new fasteners.
Front LH side air bag
module
If the front LH side air

bag has deployed:
REPLACE front LH
seatback assembly.
If the front LH side air bag has NOT deployed:
SRS
1. Check for visible signs of damage (dents, tears, deformation) of the seat back on
the collision side.
3. If damagedREPLACE the front LH seatback assembly.

Front RH side air bag
module
If the front RH side air

bag has deployed:
REPLACE front RH
seatback assembly.
If the front RH side air bag has NOT deployed:

1. Check for visible signs of damage (dents, tears, deformation) of the seat back on
the collision side.
3. If damagedREPLACE the front RH seatback assembly.
(LH or RH) side air

bag (satellite) sensor
Revision: July 2007
If any of the SRS

components have
deployed:
REPLACE the side
air bag (satellite) sensor on the collision
side with new fasteners. (Repair the center pillar inner, etc.
one if damaged.)
If any of the SRS

components have
deployed:
REPLACE the diagnosis sensor unit with
new fasteners.
1. Remove the side air bag (satellite) sensor on the collision side. Check harness
connectors for damage, terminals for deformities, and harness for binding.
2. Check for visible signs of damage (dents, cracks, deformation) of the side air bag
(satellite) sensor.
3. Install the side air bag (satellite) sensor to check fit.
4. If no damage is found, reinstall the side sir bag (satellite) sensor with new fasteners.
5. If damagedREPLACE the side air bag (satellite) sensor with new fasteners.
1. Check case and bracket for dents, cracks or deformities.

2. Check connectors for damage, and terminals for deformities.
3. If no damage is found, reinstall the diagnosis sensor unit with new fasteners.
4. If damagedREPLACE the diagnosis sensor unit with new fasteners.
SRS-63
2005 Armada
COLLISION DIAGNOSIS
Part
SRS is activated
Seat belt pre-tensioner assemblies

(All applicable locations: buckle, reel, lap
outer)
If either the driver or

passenger seat belt
pre-tensioner* has
been activated:
REPLACE all seat
belt pre-tensioner
assemblies with new
fasteners.

If the pre-tensioners have NOT been activated:
1. Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and
harness for binding.
2. Check belts for damage and anchors for loose mounting.
3. Check retractor for smooth operation.
4. Check seat belt adjuster for damage.
5. Check for deformities of the center pillar inner.
6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner
assembly.
7. If no damage is found, reinstall seat belt pre-tensioner assembly.
8. If damagedREPLACE. Install the seat belt pre-tensioners with new fasteners.
Seat (with front side

air bag)
If either the front LH

or front RH side air
bag modules has
been deployed:
REPLACE front seatback assembly on the
deployed side.
If the front LH or front RH side air bag modules have NOT deployed:
1. Visually check the seat on the collision side.
2. Remove the seat on the collision side and check the following for damage and
deformities.
Harness, connectors and terminals
Frame and recliner (for front and rear seat), and also adjuster and slides (for front
seat)
3. If no damage is found, reinstall the seat.

4. If damagedREPLACE the damaged seat parts using new fasteners. If the front
seat back is damaged, the front seat back assembly must be replaced.
Center inner pillar
1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation).
2. If damagedREPAIR the center inner pillar.
Trim/headlining
1. Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the collision side.
2. If damagedREPLACE the damaged trim parts.
Revision: July 2007
SRS-64
2005 Armada

Srs

Uploaded by

Srs

Uploaded by

H RESTRAINTS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Revision: July 2007

DIAGNOSTIC PROCEDURE 4 (CONTINUED

DIAGNOSIS SENSOR UNIT ..................................... 59

Revision: July 2007

SRS INSPECTION (FOR FRONTAL COLLISION) ...................................................................61

Occupant Classification System Precaution

Replace control unit and passenger front seat cushion as an assembly.

Trouble Diagnosis Precaution

When you read wiring diagrams, refer to the following:

GI-15, "How to Read Wiring Diagrams" in GI section

PG-4, "POWER SUPPLY ROUTING CIRCUIT" in PG section

GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section

GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section

Revision: July 2007

Removing and installing air bag lock

Commercial Service Tools

Removing steering wheel

Removing steering wheel

Revision: July 2007

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Left side collision

Right side collision

Driver air bag module

Front passenger air bag module

Front LH seat belt pre-tensioner

Seat belt buckle pre-tensioner assembly LH

Front RH seat belt pre-tensioner

Seat belt buckle pre-tensioner assembly RH

Front LH side air bag module (If equipped)

Front RH side air bag module (If equipped)

LH side front curtain air bag module

LH side rear curtain air bag module

RH side front curtain air bag module

RH side rear curtain air bag module

Revision: July 2007

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Front Side Air Bag

Side Curtain Air Bag

Occupant Classification System

Revision: July 2007

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Direct-connect SRS Component Connectors

The following SRS components use direct-connect style harness connectors.

Driver air bag module

Front passenger air bag module

LH side front curtain air bag module

LH side rear curtain air bag module

RH side front curtain air bag module

RH side rear curtain air bag module

Front LH seat belt pre-tensioner

Front RH seat belt pre-tensioner

Seat belt buckle pre-tensioner assembly LH

Seat belt buckle pre-tensioner assembly RH

Revision: July 2007

Keep ground connections clean.

AIR BAG warning lamp

HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR

Information From Customer

Battery (Refer to SC-4, "How to Handle Battery" .)

Fuse (Refer to SRS-12, "Wiring DiagramSRS" .)

System component-to-harness connections

Revision: July 2007

Revision: July 2007

Side curtain air bag modules

Front RH side air bag module

RH side air bag (satellite) sensor

Front RH seat belt pre-tensioner

Belt tension sensor

Seat belt buckle pre-tensioner assembly

Occupant classification system sensor

Occupant classification system

Front passenger air bag off indicator

10. Front passenger air bag module

11. Crash zone sensor