Scribd
Upload
270 views2 pages

Introduction To Numerical Electrostatics Using MATLAB

Three problems are presented regarding charged spheres suspended by strings. Problem 1 asks the reader to (1) find the suspension angle between two spheres as a function of their charge, (2) find the voltage between the spheres as a function of charge, and (3) find the minimum possible suspension angle. Problem 2 repeats the analysis of Problem 1 using potential energy. Problem 3 examines the equilibrium position of three spheres on an axis, where one sphere is fixed on each end and the third sphere can move, investigating whether the sign of its charge matters.

Uploaded by

rxavierva
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
270 views2 pages

Introduction To Numerical Electrostatics Using MATLAB

Three problems are presented regarding charged spheres suspended by strings. Problem 1 asks the reader to (1) find the suspension angle between two spheres as a function of their charge, (2) find the voltage between the spheres as a function of charge, and (3) find the minimum possible suspension angle. Problem 2 repeats the analysis of Problem 1 using potential energy. Problem 3 examines the equilibrium position of three spheres on an axis, where one sphere is fixed on each end and the third sphere can move, investigating whether the sign of its charge matters.

Uploaded by

rxavierva
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 2

Problems

29

Many concepts in electrostatics, such as image charges, are introduced in the chapters
where these concepts fit logically with the analyses being performed. The decision to do
this rather than introduce them in this chapter was based on the desire for brevity of this
initial chapteronly those topics that are needed to proceed were covered.

PROBLEMS
1.1

Two small spheres of mass m are suspended from weightless strings of length L. The
suspension points are a distance S apart. The spheres are charged as a capacitor; that is,
Q is removed from one sphere and placed on the other. The spheres will move toward
each other as shown in Figure P1.1.
(a) By establishing for equilibrium the force of gravity and the Coulomb force, find
the suspension angle as a function of Q.
(b) What is the voltage between the spheres as a function of Q?
(c) What is the smallest angle can assume (for nonzero Q)?

FIGURE P1.1 Two suspended charged spheres, Problem 1.1.

1.2

Repeat Problem 1.1a by finding the total potential energy of the structure and
minimizing it.

1.3

Three small charged spheres are located as shown in Figure P1.3. One sphere is fixed
at X = 0 with a charge of 1 (arbtirary units), one sphere is fixed at X = 10 with a charge
of 3, and the third sphere is free to move on the X axis, with a charge q. What is the
equilibrium position x for this system, and does it matter whether q is positive or
negative?

30

A Review of Basic Electrostatics

FIGURE P1.3 Layout for Problem 1.3.

1.4

Miniature chip capacitors are often constructed by building up successive layers


of conductors and dielectric (typically a ceramic material) and then interconnecting
the conductors, as shown in Figure P1.5. In these devices, the thickness : lateral dimensions ratio is low enough that we may use the ideal parallel plate capacitor calculation
with good results. If the dielectric thickness between successive conductor layers is h,
then the capacitance (per unit area) of the device is
C 2k0 n
=
A
h

1:80

where
k = relative dielectric constant
h = dielectric thickness between the metal layers
n = number of dielectric layers
Suppose that we are allowed a total capacitor thickness of 3 mm. Each metal layers is
0.1 mm thick. We have a choice of dielectrics with relative dielectric constant ranging
from 1 to 100. Unfortunately, however, the breakdown field of the dielectrics varies
with k as
Ep = 1 106 1 104 k

1:81

and the capacitor must be able to withstand 100 V. Find the maximum attainable
capacitance per unit area, along with the values of n and k to achieve this maximum
capacitance.

FIGURE P1.5 A multilayer chip capacitors.

You might also like