Smart BiasT

782 10253 782 10254
782 10255 782 10256

Smart Bias Tee
The Smart Bias Tee combines the performance of a standard Bias Tee
(e.g. type 793 304) with the function of an additional modem (AISG
standard) in order to provide DC voltage as well as remote control
signals via an RF feeder cable to a TMA or RCU.
The Smart Bias Tee provides low RF signal insertion loss from port 1 to
port 2 and vice versa. The measures taken to protect against static
discharge and lightning ensure a high level of reliability and operational
safety.
782 10253: 12 V version for use near the BTS, in order to feed-in DC
voltage and RCU control signals into a feeder cable
782 10254: 12 V version for use near the antenna, in order to control
an RCU (only required if no TMA is in use)
Port 1
Port 2
Port DC/RCU
782 10253
782 10255: 24 V version for use near the BTS, in order to feed-in DC
voltage and RCU control signals into a feeder cable
782 10256: 24 V version for use near the antenna, in order to control
an RCU (only required if no TMA is in use)
General Specifications:
Frequency range
Impedance
VSWR
Insertion loss
Port 1Port 2
Isolation
for DC and RCU signals
Port 1Port 2
Port 1Port DC/RCU
Port 2Port DC/RCU
Intermodulation (2x20w)
Power consumption
Lightning protection
Operating temperature
Modem carrier frequency
IP rating
Dimensions
Port 1
Port 2
8002170 MHz
50 ohms
< 1.1:1 (8002170 MHz)
Port DC/RCU
782 10254
< 0.1 dB (8002170 MHz)
>70 dB
>70 dB
0 dB
IM3: <-160 dBc
Typically 0.6 watt
3 kA, 10/350 ms pulse
-40 to +60 C
2.176 MHz
IP 66 (indoors or outdoors)
4.3 x 3 x 1.7 inches
(108.7 x 76 x 42.8 mm)
Weight
2.9 lb (1.3 kg)
Shipping dimensions
6.6 x 4 x 3.4 inches
(167 x 102 x 86 mm)
See reverse for order information.
Specifications:
782 10253
12V/BTS
Abbreviations:
RCU = Remote Control Unit for remote electrical control

of antenna tilt
BTS = Base Transceiver Station
TMA = Tower Mounted Amplifier
AISG = Antenna Interface Standards Group (version 1.1)
Port 1 = Port for BTS/Antenna (782 10253, 782 10255) or

for Antenna (782 10254, 782 10256)
Port 2 = Port for feeder cable
Port DC/RCU = Port for DC voltage and remote control

unit signals
782 10254
12V/Antenna
Connectors
Port 1 7/16 DIN male
Port 2
7/16 DIN female
782 10255
24V/BTS
Port DC/RCU
8-pin male
8-pin female
8-pin male

(IEC 60130-9)
(IEC 60130-9)
(IEC 60130-9)

Pin 1: 12 VDC in
Pin 1: 12 VDC out
Pin 6: 24 VDC in

(Pin 3: RS485-B, pin 5: RS485-A. pin 7: DC return (grounded), other pins: not connected)
Maximum input power
Port 1 or Port 2 750 watts (8002170 MHz)
Port DC/RCU
<2.5 A / +8 +14 VDC
<2.5 A / +8 +14 VDC
<2.5 A / +14 +30 VDC
782 10256
24V/Antenna
8-pin female
(IEC 60130-9)
Pin 6: 24 VDC out
<2.5 A / +14 +30 VDC
10802-H
936.2484/g
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500
Email: communications@kathrein.com Internet: www.kathrein-scala.com
Fax: (541) 779-3991
782 10253 782 10254

782 10255 782 10256
Smart Bias Tee
6$#PIN
6$#PIN
NOTCONNECTEDPIN
NOTCONNECTEDPIN
$#RETURNPIN
23"PIN
23! PIN
"LOCKDIAGRAM

7ARNING
$ONTMIX6AND6
"IAS4EESINANYCONFIGU
RATION!LWAYSCHOOSE
CORRESPONDINGVOLTAGETO
SUITTHE4-!
23! PIN
23"PIN
$#RETURNPIN
NOTCONNECTEDPIN
NOTCONNECTEDPIN
6$#PIN
6$#PIN
"LOCKDIAGRAM

!NTENNASYSTEM
SECTOR
WITHOUT4-!
!NTENNASYSTEM
SECTOR
WITH+ATHREIN4-!
!PPLICATION%XAMPLES
3 inches
(76 mm)
Please note:
The Smart Bias Tees are designed
to operate under the environmental
conditions as described in ETS
300 019-1-4 class 4.1 E and have
passed environmental tests as
recommended in ETS 300 019-2-4.
1.7 inches
(42.8 mm)
The installation team must be

properly qualified and also be
familiar with the relevant national
safety regulations.
The limits for the coupling torque
4.3 inches
of RF connectors, recommended
(108.7 mm)
by the connector manufacturers
must be obeyed.
Tightening torque for fixing the
AISG connector must lie between
0.370.74 lb/ft
(0.5 1 Nm).
0INCONNECTIONS
Order Information:
Model
782 10253
782 10254
782 10255
782 10256
Description
Smart Bias Tee
Smart Bias Tee
Smart Bias Tee
Smart Bias Tee
12V/BTS
12V/Antenna
24V/BTS
24V/Antenna
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500
Email: communications@kathrein.com Internet: www.kathrein-scala.com
Fax: (541) 779-3991

Smart BiasT

Uploaded by

Smart BiasT

Uploaded by

782 10253 782 10254

782 10255 782 10256

< 0.1 dB (8002170 MHz)

<2.5 A / +14 +30 VDC

Fax: (541) 779-3991

782 10253 782 10254

The installation team must be

Fax: (541) 779-3991

You might also like