Summary of Change

USAIS Pamphelt 350-6

Expert Infantryman Badge
This administrative revision, dated 1 May 2014- Change effective date from October 2013 to 1 May 2014 (title page).
This major revision, dated 1 May 2014- Removes Reserve Officer Training Corps (ROTC) cadets must be branched Infantry at the time
of testing. (Preface)
Removes ROTC Cadets who have already branched Infantry are eligible to test. (para 2-18 d)
Removes ROTC Cadets who are enlisted in the Simultaneous Membership Program (SMP)
with the ARNG are eligible to test only if they have already been awarded a CMF 11 MOS and
are assigned to an Infantry unit in accordance with their SMP contract. This cannot be waived.
(para 2-18 e.)
Add weapons proficiency skills testing to the end of the foot march (paras 1-1f, 8-1, 8-12, 8-13,
USAIS Form EIB Foot March 21.1 April 2014 ver 2.1)
Updates to USAIS Form EIB M249.1, April 2014 Ver 2.1
Updates to USAIS Form EIB M240.3, April 2014 Ver 2.1
Removes Reserve Officer Training Corps (ROTC) cadets must be branched Infantry at the time
of testing. (DA FORM 2823, NOV 2006 Example)
Removes ROTC Cadets who have already branched Infantry are eligible to test. (DA FORM
2823, NOV 2006 Example)

Table of Contents
Chapter 1 Introduction 5
Purpose 5
APFT 5
Land Navigation 5
Master Skills Testing 5
Individual Tactical Test Lanes 5
Foot March 6
Standardization 6
Unit Review 6
EIB Test Manager 6
Commanders Receipts of Report 7
U.S. Army Infantry School Decision 7
Authority 7
Intent 8
Exceptions and Waivers 8
Test Initiation Process 9
Score sheetss 11
Risk Assessment and Safety 11
Chapter 2 Administration and Procedures 13
Adiministation 13
Personnel Requirments 13
Grader Qualification 14
Logistical and Site Requirements 15
Candidate Eligibility Requirements 16
Medical Profiles 18
Grading Procedures 18
Phase 1 18
Phase 2 19
Phase 3 19
Phase 4 20
Phase 5 21
Operations 22
Candidate Packets 22
Chapter 3 Pre-Execution Phase 24
Unit Preparation 24
Grader Preparation 24
EIB Train-up 25
Test Validation 26
Time Line 27
Chapter 4 Army Physical Fitness Test 28

Chapter 5 Land Navigation 29

Concept 29
Candidate Conditions 29
Navigation Course Conditions 29
Day Navigation Test Standards 31
Night Navigation Test Standards 32
Chapter 6 Master Skills Testing 34
Concept 34
MST Station 1 34
MST Station 2 34
MST Station 3 34
Conditions 35
Testing 35
Chapter 7 Individual Tactical Test Lane 37
Concept 37
Lane Requirements 37
Testing 40
Chapter 8 Foot March 42
Concept 42
Requirments 42
Uniform 43
Chapter 9 Awarding the Expert Infantryman Badge and Streamer
44
Criteria 44
Chapter 10 Post Test Requirements 46
After Action Report 46
Glossary of Terms 47
Appendix A References 49
Web Resources 49
Army Regulations 49
Field Manuals 49
Appendix B EIB APFT, MST and Foot March Score sheetss
50
Appendix C Task List 105
Appendix D Adjust Indirect Fire 108
Appendix E Example ITT Score sheets 111
Appendix F Example ITT Lane 114
Appendix G Example ITT OPORD 115
Appendix H Commanders Sworn Statement 117
Appendix I Standardized Certificate 119

Preface
The United States Army Infantry School (USAIS) Pamphlet 350-6 establishes and standardizes
policies, procedures, and standards for testing and awarding the Expert Infantryman Badge (EIB).
The EIB test measures a Soldiers physical fitness and ability to perform to standards of excellence
in a broad spectrum of critical Infantry skills. Detailed instructions and forms contained in this
pamphlet ensure Army-wide uniformity.
Expert Infantryman Badge training and testing is intended to be rigorous, mission-focused and
conducted under realistic conditions. Flexibility is provided to allow units to structure the Individual
Tactical Test (ITT) lanes from an approved task list in order to develop unique scenarios that test
the Infantrymans expertise in the fundamentals, and his ability to solve problems under simulated
combat conditions. For these reasons, the EIB is appropriate for individual Soldier task training in
preparation for unit leader and collective task training.
The target audience for this pamphlet is:
Infantry Soldiers currently serving in Career Management Field 11.
Special Forces Soldiers in occupational specialties 18A, 18B, 18C, 18E, 18F, and
18Z.
Infantry Soldiers and Commissioned Infantry Officers in the U.S. Army, U.S. Army
Reserve (USAR), and Army National Guard (ARNG).
Note: This training publication can be used for other Military Occupational
Specialties as a guide for their warrior task training events; however, testing
and awarding of the Expert Infantryman Badge is specifically for
Infantry and Special Forces personnel only. This standard may not be
waived.
The proponent of this publication is the USAIS. Send comments, recommendations, and all other
correspondence related to this manual to the following address:
Chief of Infantry, USAIS
ATTN: ATSH-IP (EIB)
1 Karker Street, Suite 6100
Ft. Benning, GA 31905-5593
Phone: 706.604.5170
Web Site: www.benning.army.mil/infantry/eib

ROBERT E. CHOPPA
Colonel, Infantry
Chief of Infantry

Chapter 1

Introduction
PURPOSE
1-1. The purpose of the EIB is to recognize Infantrymen who have demonstrated a mastery of
critical tasks that build the core foundation of individual proficiency that allow them to locate, close
with, and destroy the enemy through fire and maneuver and repel an enemy assault through fire and
close combat.
The Army Physical Fitness Test (APFT), Day and Night Land Navigation, Weapons Master Testing
(MST) station, Individual Tactical Test (ITT) lanes, Foot March, and the Weapons Proficiency Test
must be planned, resourced, executed and assessed in a five (5) day period. These evaluations place
eligible Candidates under varying degrees of stress that test their physical and mental abilities as they
execute critical Infantry tasks to established standards. The scope for each of these events follows:
a. APFT. The APFT tests the physical endurance and conditioning of the Candidates, and is
the first graded event they will undertake. The APFT is conducted to standard in accordance
with FM 7-22. Candidates must meet height and weight requirements as outlined in AR
600-9. The APFT is not re-testable nor can it be waived. Refer to Chapter 4 for more
details on this event.
b. Land Navigation. Land Navigation tests the ability of Candidates to navigate from one
point to another using a map and compass while equipped with their individual combat gear.
This is the second graded event they will undertake, demonstrating their proficiency under
both day and night conditions. Land Navigation testing will be conducted in accordance
with FM 3-25.26 and is not re-testable. Unit level waivers are considered on a case by case
basis. Refer to Chapter 5 for more details on this event.
c. Master Skills Testing. Master Skills Testing station evaluates individual proficiency
and confidence with weapons systems common to an Infantry Company, as well as their
associated functions. MST is conducted to a defined standard in a formal, round-robin
fashion. MST is re-testable and Candidates must pass each MST station in order to continue
to the ITT lanes. Refer to Chapter 6 for more details on this event.
d. Individual Tactical Test Lanes. ITT Lanes evaluate a Candidates ability to demonstrate
their tactical and technical proficiency of individual Infantry tasks to standard. Lanes are
scenario driven, incorporating stressors and conditions that force Candidates to constantly
adapt to changing situations as they attempt to achieve a successful overall outcome of a
simulated Infantry mission. This phase of testing differs from a controlled round-robin
evaluation, as Candidates tactically complete a series of individual tasks to acceptable
standards while the environmental conditions are changed. ITT lanes are not re-testable.
Refer to Chapter 7 for more details on this event.
Page: 7

f. Foot March. The foot march and completion of the weapons proficiency skills test are
the last events in the EIB test. Candidates must complete 12-mile route in three hours or
less, and then successfully complete the tasks associated with the weapons proficiency skills
to receive a Go for the foot march. Both events will be conducted according to standards
established in this publication, with additional standards for the foot march outlined in FM
21-18. The foot march and the weapons proficiency test are not re-testable. Refer to Chapter
8 for more details on this event.

STANDARDIZATION
1-2. The Chief of Infantry, USAIS, is responsible for the standardization and implementation of
the EIB test. The Chief of Infantry reserves the right to revoke testing authority to any unit who fails
to comply with the regulations and standards established in this pamphlet.

UNIT REVIEW
1-3. USAIS reserves the right to conduct reviews and validation of any unit during the
administration of their EIB test and make recommendations for change to test events up until the
day of testing.

EIB TEST MANAGER

1-4. The Chief of Infantry appoints Senior NCOs who have earned the EIB to serve as Test
Manager. All Test Manager appointments are made through orders and their responsibilities include
the following:
a. Serve as the primary point of contact for EIB training and testing to all eligible units in
the Army, Army National Guard, and Army Reserve.
b. Conduct site visits with units approved to conduct EIB testing in order to assist as needed
with test site establishment, administrative processes, and validation of the EIB test site prior
to testing.
c. Observe units during EIB testing to determine if the process complies with the regulations
and standards outlined in this pamphlet.
d. Report all observed deviations of regulations and standards to the unit EIB Board
President and recommend changes or specific corrective action during the conduct of
the test. (The Test Manager report is exempt from management information control
requirements IAW AR 33-15, paragraph 52.)
Page: 8

e. Submit a report of any unresolved discrepancies of regulations or standards through

the testing unit Commander. The Test Manager is obligated to report all uncorrected
discrepancies to the Chief of Infantry or his designated representative. At his discretion, the
Chief of Infantry can revoke authorization for testing; however, Candidates awaiting final
evaluations of unresolved test deviations can complete the EIB test events. In this instant,
EIBs will not be awarded to Candidates until the Chief of Infantry determines that all
discrepancies have been resolved and the unit is authorized to conclude the EIB test process.
f. Submit an After Action Report (AAR) to the Commander of the testing unit of
observations made during the units train-up and testing. If applicable, the AAR will also
include a section of unresolved issues or deviations observed that were not serious enough
to impact the outcome of the test. This AAR must be submitted within 15 days of test
conclusion.

COMMANDERS RECEIPT OF REPORT

1-5. If the AAR provided to the Commander of a testing unit lists any unresolved issues or
deviations, the Commander will be required to submit a summary report to the Chief of Infantry
within 15 days of receiving his report. The Commanders summary should address what actions have
been taken to address the unresolved issues, or state why he feels the issues raised are unjustified. All
correspondence should be directed to the address listed in the preface of this publication.

U.S. ARMY INFANTRY SCHOOL DECISION

1-6. Upon receiving the Test Manager report and the Commanders Summary Report, the Chief
of Infantry will review the issues and make a determination based on the facts as to the validity of the
test and if authorization to award the EIBs for that test will remain in effect. A written response of
his decision will be provided to the Commander within a timely manner.
1-7. In extreme situations where the Test Manager feels the integrity of a test is in question, the
Chief of Infantry may choose to revoke a test control number until all deviations have been resolved
to his satisfaction. If a test control number is revoked, the test is considered invalid and no EIBs may
be awarded.

AUTHORITY
1-8. Commanders and Commandants of the following organizations are authorized to administer
EIB testing and request awarding of the EIB to qualified personnel:
Divisions
Divisional Brigades or Regiments when the Division Commander delegates the
Page: 9

authority to them.
United States Army Training Centers (ATC).
Separate Infantry Battalions when they receive the authority from a Commander who
has general court martial authority over the Battalion.
Special Forces Groups.
Separate Special Forces Battalions when they receive the authority from a
Commander who has general court martial authority over the Battalion.
National Guard Brigades, Battalions, and Special Forces units when they receive the
authority from the Adjutant General or authorized designee.
1-9. Commanders and Commandants who choose to administer an EIB test to their units must
be Infantry Branch officers. If the Commander or Commandant is not an Infantry officer, they
will need to appoint an Infantry officer from within their unit to serve as the Officer in Charge
of the EIB test, who may also be appointed as the President of the EIB Board. Commanders and
Commandants are not authorized to conduct EIB testing or request award of the EIB without
receiving a Test Control Number (TCN) from USAIS.

INTENT
1-10. Commanders offer the opportunity to test for the EIB to any qualified CMF 11 or CMF 18
personnel who volunteer to undergo the process. Special Forces Medics (MOS 18D) are not eligible
to test for the EIB as they are able to test for the Expert Field Medical Badge (EFMB). Commanders
will submit a request for awarding the EIB through the Chief of Infantry for all qualified personnel
who pass all five testable events that comprise the EIB test.
1-11. Commanders may administer the EIB test as often as their operational tempo will allow.
Multiple tests conducted by the same unit will require separate TCNs obtained through the USAIS
Test Manager.
1-12. Testing should create an environment where Candidates strive to demonstrate their
mastery of critical combat skills while meeting established standards set forth in the ATTPs, FMs,
SMCTs, TCs, and TMs. The training that Candidates undertake while preparing for the EIB test
will improve their survivability on the battlefield by highlighting weaknesses and strengths while
providing increased confidence in their own abilities.
1-13. Throughout the test, graders evaluate each Candidates performance constantly in order to
clarify and capture key points for discussion during formal and informal feedback sessions. During
test validation, graders should make every opportunity to clarify concerns by asking questions during
the walk through and various briefings conducted by the Test Manager.

Page: 10

EXCEPTIONS AND WAIVERS

1-14. Commanders may request exceptions to this publication through the Test Manager except
where it is specifically noted that waivers or exceptions are not permitted. All requests will be
considered on a case by case basis.
1-15. Requests for waivers or exceptions should be addressed to the Test Manager no later than 30
days prior to the beginning of testing. The Test Manager will work with all units in addressing their
specific issues through the entire EIB process.

TEST INITIATION PROCESS

1-16. The following must take place within a unit in order to initiate the EIB process:
a. Commanders and Commandants are responsible for the following actions:
1) Allow enough time for proper test preparation, coordination, and unit level
training to take place prior to the EIB train-up period and subsequent test period.
2) Allocate internal resources and establish support and training priorities in relation
to EIB preparation, training, and testing.
3) Appoint a three member EIB board from within the unit consisting of a Board
President and two members. The Board President must be a CSM or at least a
Major, and the additional members of the board must be at least Sergeants First
Class. Board members must be either CMF 11 or CMF 18 personnel and have
already been awarded the EIB.
4) Designate key personnel to coordinate with the Test Manager and request
authority from the USAIS to conduct EIB testing. Coordination should occur 45
days prior to the start of the EIB train-up period for CONUS units, and 60 days
prior to the start of the EIB train-up period for OCONUS, ARNG, and USAR
units.
5) Issue appointment orders for all EIB Board members and graders.
6) Ensure a Line of Accounting is provided to the Test Manager through the Defense
Travel System to cover TDY costs for the Test Manager. Units are responsible for
funding Test Manager travel for EIB validation.
7) Request issuance of award orders and certificates to personnel who pass the EIB
test through the Chief of Infantry.
8) Ensure S-1 personnel upload EIB orders into the individual iPERMS accounts of
recipients.
Page: 11

9) Ensure the EIB Board provides the required AAR report to the Test Manager
detailing unit performance during the course of testing within 15 days of test
completion.
b. The EIB Board is responsible for the following:
1) Applying proper backward planning from the start of the EIB train-up and test
period in order to develop a realistic training plan for the unit for the period prior to
and beginning of the EIB test.
2) Obtain command guidance for training emphasis which will dictate the focus of
the ITT lanes.
3) Select which Skill Level 1 tasks each ITT lane will consist of.
4) Appoint an NCOIC for each lane and an adequate number of graders for the
entire event. All NCOICs and graders must be EIB recipients and must be certified
by the Board in accordance with the standards outlined in this publication.
5) Issue an Operations Order to the unit detailing the EIB process, assign and
delegate tasks as needed, and conduct unit IPRs through all stages of the EIB process.
6) Submit a test concept and schedule to the Test Manager no later than 30 days
prior to the EIB train-up and validation period, with an information copy provided
to the responsible Major Army Command (MACOM). The Board should remain
flexible to make changes to the test concept in accordance with guidance provided by
the Test Manager.
7) Ensure all EIB Candidates meet the prerequisites outlined in this publication and
supporting regulations. Under no circumstances will the Board allow unqualified
personnel, to include non-CMF 11 and non-CMF 18 personnel, to take part in the
actual EIB test.
8) Consolidate all appointment orders and EIB orders for Board members and
graders for review by the Test Manager during the validation phase of EIB.
9) Organize, administer, control, and execute all phases of the EIB process to
standard, to include training and testing.
10) Verify all individual score sheets through every phase of testing.
11) Ensure that Candidates that are eliminated from testing are not re-integrated
into the EIB test. Eliminated personnel must wait for the next EIB process in order
to test again.
12) Provide official notification to the Commander or Commandant of all personnel
who successfully complete the EIB test and become eligible to be awarded the EIB.
Page: 12

13) Within 15 days of completing the EIB test, submit an AAR to the Test Manager
listing EIB recipients by name, a copy of all EIB orders issued, and the required test
tracking report.
14) The EIB Board may reproduce any portion of this publication or associated
training materials, check lists, and score sheets as required.
c. The Test Manager is responsible for the following:
1) Ensuring the USAIS PAM 350-6 remains updated and relevant while providing
relevant supporting documentation and reference items to all units engaged in the
EIB process.
2) Track all units requesting authorization to test and assisting units as required
through the EIB process.
3) Travel to all test locations during the final train-up phase in order to validate the
test site, validate the graders and members of the Board, and validate that Candidates
meet all prerequisites for EIB testing.
4) Offer guidance as needed to correct deficiencies with test sites and report to the
Chief of Infantry all instances where discrepancies cannot be adequately resolved.
5) Upon validating a test site, issue a Test Control Number (TCN) to the testing
unit. A TCN should be provided prior to the first day of testing, but may be
withheld if a test site does not meet the requirements established in this publication.
6) Submit an AAR for each test validated to the Chief of Infantry within 15 days of
test completion. A courtesy copy of the AAR should be provided to the unit as well.

Score Sheets
1-17. Units must use the provided score sheets for grading the MST stations; however, units are
responsible for creating their own score sheets for the ITT lanes since they choose their own tasks for
testing. MST score sheets and standards are located in Appendix B and an example ITT score card
can be found in Appendix E.

RISK ASSESSMENT AND SAFETY

1-18. The unit Commander will apply composite risk assessment and risk management procedures
throughout the entire EIB process, putting in place appropriate controls as needed in order to
eliminate hazards and reduce risk.
1-19. Safety violations that pose a hazard to life, limb, or eye sight, as well as an intentional
Page: 13

disregard for safety measures and controls, may result in a Candidates immediate removal from the
test process at the discretion of any NCOIC and the EIB Board.

Page: 14

Chapter 2

Administration and Procedures

ADMINISTRATION
2-1. Once the decision is made to conduct an EIB test, the authorized Commander or
Commandant should immediately appoint an EIB Board President and two Sergeants First Class or
higher to serve as members of the EIB Board. All members of the board must be eligible CMF 11 or
CMF 18 personnel who have earned the EIB already. If qualified personnel cannot be found within
the unit, then qualified personnel from outside the unit may be appointed to the EIB Board.
2-2. The EIB train-up and test must be completed within 12 consecutive days for active duty
units, as well as mobilized ARNG and USAR units. Units should also have a concurrent training
plan in place for personnel not involved in testing and for Candidates who fail to meet the test
requirements and are eliminated from the process.
2-3. Authorized ARNG and USAR units that are in a non-mobilized status and conduct
traditional M-Day or TPU training may complete the EIB train-up and test as follows:
a. Complete the train-up and test over two consecutive Inactive Duty Training (IDT)
periods consisting of at least 9 Mandatory Unit Training Assemblies (MUTA).
b. Complete the train-up and test over 12 consecutive days during their authorized Annual
Training (AT) period.
c. Complete the train-up over the IDT period immediately prior to Annual Training and
conduct testing during AT. If this option is used then the train-up should be conducted over
a MUTA-9 IDT period and testing must be completed within the first eight days of AT.
d. Complete the train-up over the Annual Training period and conduct the test during the
first IDT period immediately following AT. If this option is used then the train-up should
be conducted within the last eight days of AT and the test should be conducted over a
MUTA-9 period.
2-4. ARNG and USAR units should factor in the need for supporting personnel when planning
their EIB, as well as a need for additional funds for TDY and Active Duty Operational Support
orders.

PERSONNEL REQUIREMENTS
2-5. Personnel required to serve as the EIB Cadre who will administer and support the EIB
process will vary based on the size of the unit testing as well as the number of Candidates involved
Page: 15

in the process. All EIB Cadre must have already been awarded the EIB this requirement cannot
be waived. The following is provided only for reference for a Battalion size element and should be
adjusted as needed by the EIB Board:

(1) EIB Board President (CSM or Higher)

(2) EIB Board Members (SFC or Higher)
(1) SFC or above to serve as the NCOIC of the EIB Operations Center
(3) Personnel to support the EIB Operations Center
(3) 1SG/MSG to serve as Lane NCOICs
(3) SFCs to serve as Quality Control NCOs for the lanes 1 per lane
(27) SGT through SFC to serve as lane graders 9 graders per lane (3 per sub-lane)
(9) SGT through SFC to serve as MST graders 3 graders per MST station
(1) SFC to serve as the Land Navigation NCOIC
(10) SGT through SFC to support Land Navigation and serve as graders

2-6. The NCOIC for the APFT and Foot March can come from the same personnel used as Lane
NCOICs if units are short of qualified personnel. This is possible as these events take place on their
own specific day outside of the MST and ITT lanes testing. In addition, the graders for the MST
stations, ITT lanes, and Land Navigation can also be used to support the grading and execution of
the APFT and Foot March.
2-7. If units do not have all the personnel required by specific grade for these positions, a request
for waiver may be submitted to the Test Manager with a list of the personnel and their rank and the
positions they will be appointed to.
2-8. In addition to the EIB Cadre listed in paragraph 2-5, units will need to factor in support
personnel to assist with the day to day operations of the EIB (logistics, ammunition, transportation,
medics, communications, meals, etc.). These support personnel do not have to be EIB recipients.

GRADER QUALIFICATION
2-9. The EIB Board is responsible for qualifying all EIB Graders and providing supporting
documentation to the Test Manager during the unit validation process. Personnel selected to serve as
a Grader for the EIB must meet the following criteria:
a. Must be a Sergeant through First Sergeant/Master Sergeant. A unit may request a waiver
for this requirement if they are short of qualified NCOs. If the waiver is approved then
Specialists may be appointed as a grader on a case by case basis. If selecting Specialists as
graders, efforts should be made to ensure they are already serving as Team Leaders.
b. Must have previously been awarded the EIB and have a copy of the orders.
c. Must hold a CMF 11 or CMF 18 MOS (Excluding 18D Medics).
Page: 16

d. Must meet height and weight requirements outlined in AR 600-9.

e. Must be appointed by orders to serve as a grader.
2-10. All phases of the EIB test will be graded by qualified personnel as outlined above, except in
the following situations where subject matter expertise (SME) may be utilized:
a. Using a Medic to evaluate first aid tasks.
b. Using an Artilleryman to evaluate Call for Fire.
c. Using a Radio Operator to evaluate communications tasks.
d. Using Chemical personnel to evaluate Chemical, Biological, Radiological, and Nuclear
(CBRN) tasks.
2-11. If a unit chooses to utilize SME evaluators to assist in the evaluation of specialized tasks, the
following will apply:
a. SME evaluators must be an NCO.
b. SME personnel must be qualified through the EIB Board and appointed by orders.
c. SME personnel will only be used to evaluate tasks specific to their expertise and will
provide feedback to the grader on a Candidates performance. Graders will have the final
authority in determining if a Candidate has passed the event or not. Under no circumstances
will SME personnel be utilized as graders for any event conducted within the five phases of
the EIB test.
d. SME evaluators will be supervised by the ITT Lane NCOIC where their expertise is
being utilized. SME evaluators will not be involved in the final decision process for any
appeals outside of providing their professional opinions to the lane NCOIC. SME personnel
have no authority to make final determinations regarding Candidates testing for the EIB.
2-12. The EIB Board must ensure that all graders are trained to evaluate their respective areas to the
same standard. This is especially important when multiple units are testing together and may operate
under a different TACSOP. It is vital that one standard is established which is readily understood by
all graders, which will ensure a uniform grading practice is in place for all phases of the EIB test.

LOGISTICAL AND SITE REQUIREMENTS

2-13. Units may conduct the EIB train-up and testing either during the day or during the night.
Site selection should be based on the number of Candidates that will be training and testing,
Page: 17

allowing enough room to construct adequate lanes and allow for a good flow of Candidates through
the various stations.
2-14. Equipment requirements are based on the number of Candidates testing, the tasks that are
being evaluated, and the composition of the testing unit. Testing will be administered to a Battalion
size element or larger comprised of eligible Candidates drawn from eligible units.
2-15. Ammunition allocation should follow established policies for units testing, while ensuring
ammunition requests are entered into TAMIS at least 90-days prior to the scheduled drawing from
the ASP.
2-16. In order to centralize resources and consolidate EIB Cadre in one location, training on the
actual test site is permitted if the unit chooses to do so. If training and testing is conducted on the
same site the EIB Board needs to ensure that training scenarios differ from testing scenarios. Some
examples for creating different scenarios follow:
a. Train on several first aid tasks without Candidates knowing which will be included in the
test.
b. Change grid locations for targets.
c. Change call signs, frequencies, distances, and directions of simulated engagements.
d. Change the sequence that Candidates will encounter tasks on an ITT Lane.
2-17. Reference materials, training aids, and periods of instruction are not permitted inside of the
Holding Areas during EIB testing.

CANDIDATE ELIGIBILITY REQUIREMENTS

2-18. Before being permitted to test for the EIB, prospective Candidates must meet the following:
a. Must be an active member of the U.S. Army, ARNG, or USAR. South Korean Soldiers
assigned by paragraph and line number to U.S. Army Infantry units are eligible to test for the
EIB.
b. Enlisted personnel must possess a CMF 11 or CMF 18 MOS as their primary MOS.
Personnel holding the 18D MOS are not eligible to test for the EIB. Secondary and
additional Military Occupational Skills will not be considered in meeting this requirement.
This cannot be waived.
c. Officers must be branch qualified as Infantry or Special Forces. Officers who are
branch detailed to the Infantry may test for the EIB as long as they have completed the
Infantry Officer Basic Course and are still on loan to the Infantry from the donor branch in
Page: 18

accordance with AR 614-100. This cannot be waived.

d. Must meet all height and weight requirements outlined in AR 600-9. This cannot be
waived.
e. Must have qualified expert with the M4 Carbine or M16 Rifle on a 300 meter RETS
range within six months of testing for the EIB in accordance with FM 3-22.9. ARNG
and USAR personnel must have qualified within one year of testing for the EIB. This
prerequisite cannot be used to offset any testing requirements which occur within the
EIB process. In instances where a 300 meter RETS range is not accessible to the unit,
qualification on the ALT-C course is acceptable; however, the unit will need to justify their
inability to access a 300 meter RETS range via memorandum to the Test Manager. ALT-C
is not permitted in order to provide an additional attempt for weapons qualification for
personnel who have been afforded an opportunity to qualify on a 300 meter RETS range
prior to EIB testing. This cannot be waived.
f. Must volunteer for testing and have received the recommendation of their current
Commander to participate in testing.
g. In instances where a unit is operating in an OCONUS environment in conjunction
with foreign allied forces, where a treaty or cooperative agreement exists, the senior Infantry
Commander may extend an invitation to these forces to participate in the EIB process.
Allied forces who participate in the EIB process must meet all established criteria within this
manual to be considered an eligible Candidate, to include holding an equivalent Infantry
primary MOS. Foreign forces not meeting these requirements cannot take part in any
portion of the EIB process under any circumstance. Foreign forces will not be utilized as
graders or officials for the EIB process; however, designated foreign leadership should be
present at every station to facilitate command and control of their troops as well as serve
as translators. Allied personnel who successfully complete the EIB test to standard may
be awarded the EIB Certificate, EIB orders, and the EIB badge in accordance with their
prescribed uniform and award regulations.
h. In instances where foreign allied forces are operating with, or attached to, American units
within CONUS boundaries, the senior Infantry Commander may extend an invitation to
these personnel to participate in the EIB process in accordance with the guidance established
in paragraph 2-18(g) of this pamphlet listed above.
2-19. At a Commanders discretion, eligible Soldiers may be assigned or attached to a testing unit
for the sole purpose of participating in the EIB process when the parent unit is not conducting a test.
2-20. The unit which has been authorized to administer a test is the only entity able to award the
EIB, orders, and certificates. This cannot be delegated to another authority nor can it be waived.
2-21. Company Commanders, or equivalent, are responsible for certifying that their Soldiers meet
all eligibility requirements to test for the EIB and are required to provide a roster of their Candidates,
Page: 19

with supporting documentation, to the EIB Board. In order to maintain the integrity of the test,
certification must be submitted in memorandum format accompanied by a sworn statement. An
example of these documents can be found in Appendix I.

MEDICAL PROFILES
2-22. In order to prevent inflicting further injury to personnel who have been placed under
physical constraints of a temporary medical profile for injury or illness, these personnel will not
be permitted to test for the EIB. Personnel in this situation who feel that they have recovered to a
satisfactory level of fitness to take part in the EIB process must first be cleared by competent medical
authority.
2-23. Personnel who have received a permanent medical profile may test for the EIB as long as
their profile will not prevent them from taking part in any of the required events. These personnel
are permitted to take the APFT and any alternate event that they have been delegated to take in
place of a normal APFT event. In these instances personnel must pass their alternate event in
accordance with regulations, as well as score 75% or better in their age group for any regular event
they are permitted to perform.
2-24. Personnel who have received a PULHES rating of 3 or higher in any category must have been
assessed through the MOS Medical Retention Board (MMRB) process or the MOS Administrative
Retention Review (MAR2) program and approved for retention in either the CMF 11 or CMF 18
fields. Personnel who were denied retention within these CMF fields after completing either medical
review process are not eligible to test for the EIB.

GRADING PROCEDURES
2-25. Candidates must successfully complete all five phases of the EIB test to standard in order to
receive the award. Grading of each phase of the test is accomplished as follows:

a. Phase 1. Consists of the APFT. The APFT will be administered by the EIB
Board utilizing the EIB Cadre as graders. This event can only be graded by EIB Cadre
who have earned the EIB and were appointed by orders. The APFT will be executed in
accordance with FM 7-22, with the exception that each Candidate must score 75% in each
event for their appropriate age group in order to receive a GO and progress to Phase 2 of the
EIB test. Failing to score 75% in each event for their appropriate age group will result in
a NO-GO and eliminate a Candidate from the EIB test. This phase is not re-testable and
none of the criteria can be waived.

b. Phase 2. Consists of day and night land navigation. Land navigation will be
administered by the EIB Board Land Navigation NCOIC and graded by EIB Cadre. This
event can only be graded by EIB Cadre who have earned the EIB and were appointed by
orders. The land navigation site will be established in accordance with the standards outlined
Page: 20

in FM 3-25.26. In order to receive a GO in this phase, Candidates are required to locate

three out of four points in their assigned lane for both the day and night iterations within a
two-hour time period. In addition, during the day iteration Candidates are required to find
and record their start point with a 6-digit grid. A Candidate will receive a NO-GO if he
fails to locate three of his four points within the established time line on either the day or the
night course, and fails to locate and identify the 6-digit start point during the day iteration.
This phase is not re-testable.

c. Phase 3. Consists of Master Skills Testing (MST), which is executed in
conjunction with the Individual Tactical Test (ITT) Lanes. MST will be administered by the
EIB Board and can only be graded by EIB Cadre who have earned the EIB and are appointed
by orders. This phase of testing is performance based and concentrates on weapons
proficiency conducted at static stations where a Candidate has the tasks, conditions, and
standards fully explained while offered a chance to ask questions before starting the timed
evaluation. While the timed events create individual stress, a Candidate is not required to
evaluate a changing environment as environmental conditions will not change at each MST
station. Candidates are evaluated strictly to the standards established on the grading sheets
in Appendix B and will either receive a GO or a NO-GO as follows:
(1) Candidates who master each weapon system without missing a performance
measure receive a GO and continue to ITT Lanes upon successful completion of the
MST stations.
(2) Candidates who miss a performance measure are immediately stopped by the
Grader and told what they did wrong. At this point the Candidate returns to the
holding area for no more than one hour while waiting to re-test. Candidates have the
option to make their second attempt in less than the one hour period at their own
choosing.
(3) Candidates who are required to re-test will return to the MST station and
resume where they received the initial NO-GO, although with a different grader. If a
Candidate receives a second NO-GO (Double NO-GO) on the same weapon system
during the re-test they are eliminated from the EIB test.
(4) Candidates who receive a GO at an MST station upon re-test are permitted to
continue with the remaining MST Stations. If a Candidate receives another NOGO on a different weapon system, they will return to the holding area and re-test as
outlined above.
(5) Candidates are required to pass all MST stations before being permitted to enter
the ITT lanes.
d. Phase 4. Consists of the Individual Tactical Test (ITT) Lanes. Grading of the
ITT Lanes incorporates the knowledge, tactical proficiency, experience, and understanding of
unit level Tactical SOPs (TACSOPS) and Infantry doctrine by the graders.
Page: 21

(1) Graders must have the ability to discern what is tactically acceptable under the
test conditions and determine if one of the following criteria applies:
(a) A Candidate has demonstrated mastery of the skills required that ensure
mission success and individual survivability.
OR
(b) A Candidate has simply negotiated a lane through unskilled actions
resulting in the appearance of successful execution.
During this phase of testing, tasks must be performed to the highest standards that would enable an
Infantryman to destroy an enemy on the battlefield while surviving and remaining a viable combat
asset.
(2) As a Candidate enters a lane, their performance is evaluated from the perspective
of an Infantry leader evaluating a Soldier from the initial phases of mission execution,
to include pre-combat checks, through the final phases of consolidation and
reorganization . Graders should evaluate the manner that changing situations are
assessed, controlled, and overcome by Candidates, as well as their ability to adapt.
Standards for each task remain unchanged; however, tactical latitude can be applied
in the manner that the Candidates execute a task. It is the responsibility of the grader
to place the Candidates overall execution of each task within the context of the
environment and determine if the task would have been performed with satisfactory
results in combat, or resulted in catastrophic failure.
For the purpose of EIB testing, catastrophic failure exists if one or more of the following would
reasonably result from a Candidates actions:

Loss of own life or incurring serious injury to self.

Inflicting serious injury or death to friendly forces, wounded, or prisoners.
Violating the Laws of War.
Loss of vital equipment through negligence or poor judgment.
Compromise of operational and/or sensitive information.
Failing to accomplish the mission.

As a Candidate executes tasks under simulated combat conditions within a lane, the following may
be acceptable:
Performance measures are skipped, performed out of sequence, or consolidated into
one overall action.
Actions are modified during task execution.
This is acceptable as long as these actions demonstrate a proficient understanding of the task and
how it is applied to surviving, winning the fight, and accomplishing the mission. When considering
if a Candidate receives a GO or NO-GO, a grader must evaluate how each individual task was
Page: 22

executed on the lane and determine if the actions taken for each would have resulted in mission
success or catastrophic failure. Catastrophic failure only applies to an entire lane when a Candidate
fails to complete the lane within the allotted time.
(3) In making this determination a grader must first evaluate what sub-tasks or
performance measures were missed in the execution of each task, then determine if
those oversights would result in failing to attain the desired outcome of each task in
conjunction with the overall mission scenario of the lane. If a Candidates actions or
inactions would result in catastrophic failure as defined above, then the Candidate
should receive a NO-GO for that task. Graders must be familiar with all tasks,
conditions, and standards and have them readily available during the grading process.
It is acceptable to incorporate the tasks, conditions and standards into the actual
score sheets to facilitate grading.
(4) In order to remain in the EIB process, Candidates can receive no more than
two NO-GOs upon completion of a lane. Candidates entering a lane with NOGOs from other lanes or MST stations cannot have more than two NO-GOs upon
completion of the lane. Re-testing is not permitted within the ITT lanes.
(5) Graders will not interrupt or stop a Candidate once the lane is started unless an
unsafe action is observed. Graders will observe and evaluate through the entire lane,
making notes on the Candidates performance. Graders will advise Candidates on
their performance once they reach the end of the lane. Candidates should not receive
any indication of how they are doing while they negotiate a lane.
(6) Upon completing a lane, graders will provide Candidates with AAR comments
for minor issues that occurred within the lane, as well as advising them of any NOGOs they received and why a NO-GO was given.
(7) When selecting tasks for each lane, the EIB Board will establish the acceptable
minimal standards for each task. The EIB Board must ensure that the standards
are clearly understood by all graders, that all grading is consistent, and that all
Candidates understand what is required of them.
e. Phase 5. Consists of the 12-mile Foot March and is administered by the EIB Board
utilizing the EIB Cadre as graders. This event can only be graded by EIB Cadre who
have earned the EIB and were appointed by orders. The Foot March will be executed in
accordance with FM 21-18 while Candidates carry 35 pounds of dry weight in addition to
their individual combat equipment, water, and an M4 carbine or M16 rifle. This event is a
GO or NO-GO event and must be completed in three hours or less. Candidates who fail to
pass the foot march are eliminated from the EIB process. This phase is not re-testable and
none of the criteria can be waived.
2-26. Candidates must make a valid attempt at every graded event and task. Any attempt to
intentionally bypass an event or task will result in immediate elimination from the EIB process. This
Page: 23

cannot be waived; however, a Candidate may appeal to the NCOIC of the testing phase where the
violation occurred. The NCOIC is the final authority.
2-27 Any unsafe act committed by a Candidate will result in immediate elimination from the EIB
process. This cannot be waived; however, a Candidate my appeal to the NCOIC of the testing phase
where the violation occurred. The NCOIC is the final authority.
2-28. During all phases of testing, Candidates are evaluated by one grader who either observes the
Candidate through every individual task performed, or evaluates the end-state of their performance.
Graders are accountable to either an event NCOIC or a lane NCOIC during all phases of testing.
NCOICs have overall responsibility and authority for their event or lane, to include appeal authority.
2-29. NO-GOs are cumulative throughout the MST and ITT phases of the EIB test. Candidates
are eliminated from EIB under the following grading criteria:
a. Failing to pass any GO or NO-GO event.
b. Receiving two consecutive NO-GOs (double NO-GO) on the same weapon system
during MST testing after being afforded the opportunity to re-test.
c. Receiving a cumulative total of three NO-GOs over the course of the MST and ITT
testing phases.
d. Failing to complete an ITT lane within the specified time, as this results in receiving a
NO-GO for all tasks within the lane.

OPERATIONS
2-30. During the train-up and testing phases, all operations should be coordinated through a
consolidated EIB operations center under the supervision of an Operations NCOIC appointed
through orders by the EIB Board. The Operations NCOIC is responsible for consolidating and
maintaining all Candidate packets and score sheets through all phases of testing.

Candidate PACKETS
2-31. The EIB Board is responsible for determining the content and format of Candidate packets,
performance review forms, and score sheets for each event, with the exception of the MST score
sheets provided in this pamphlet. At a minimum, Candidate packets should include the following:
a. Rank, Full Name, MOS, Parent Unit
b. Date of Rifle Qualification and Score
Page: 24

c. Individual Score sheets for all EIB events

d. Summary Score Sheet Providing Overall Test Progress

Page: 25

Chapter 3

Pre-execution Phase
UNIT PREPARATION
CONCEPT
3-1. Commanders should integrate EIB test events and subjects into individual and collective
training programs at least 120-days prior to EIB execution. Sustainment training for physical fitness
and land navigation will greatly improve the overall outcome of the EIB test success rate. In addition
it is highly recommended for Commanders to allocate sufficient squad level training focusing on
weapons proficiency skills to ensure Soldiers are properly prepared for the MST stations they will test
on.
3-2. The scheduled train-up period integrated into the EIB process is not designed to instill a level
of proficiency to successfully pass the EIB test. This train-up period serves as an indicator for the
EIB Board to determine if there are failure points within their plan, identify problems with the test
flow, and offers an opportunity to make slight adjustments prior to test execution while providing
the Candidates with an understanding of how they will negotiate the test and fine-tune their skills.
3-3. Once the EIB tasks have been approved by the EIB Board, all subordinate testing units
should be advised and directed to reference the Army Training Network (ATN) at https://atn.army.
mil/ for tasks, conditions, and standards for training purposes. ATN is the only authorized resource
for obtaining this information for the EIB test, which ensures a uniform standard throughout the
force. Units may create their own training manuals; however, quality control measures should be put
in place when creating training manuals to ensure Candidates are being provided with the correct
information.
3-4. Efforts should be made to conduct all EIB training under the same conditions that the test
will be administered whenever possible. EIB testing may be conducted during daylight hours or
during hours of darkness at the discretion of the Commander.

GRADER PREPARATION
3-5. The EIB Board is responsible for training and certifying all graders and EIB cadre personnel.
This process should take place concurrently with the unit train-up phase 120-days prior to EIB
execution. All graders and cadre should be trained and certified by the EIB Board prior to the Test
Manager validation of the EIB test site. Training and certification of these personnel should ensure
the following at a minimum:
a. A complete understanding of all events and tasks that will be tested.
Page: 26

b. Knowledgeable in the time line for the entire EIB process.

c. Knowledgeable in the grading standards for each testable phase of the EIB test.
d. A complete understanding of their specific roles in the EIB process; grading standards
and requirements for their specific area of responsibility; and a complete understanding of all
tasks, conditions, and standards within their area of responsibility.
e. Trained in all recording and paperwork requirements.
f. Trained in the appeals process.
g. Understand all safety and risk mitigation requirements for all phases of testing.
h. Understand the MST re-test procedures.
3-6. Training and certification of graders and cadre should require them to demonstrate their
proficiency in their areas of responsibility through practical demonstration to the EIB Board. These
personnel should be placed in positions where they will rotate through the various positions that
they will serve in, scoring and performing the tasks they are responsible for. The EIB Board should
designate role-players to act as Candidates for personnel to grade and interact with. These roleplayers should intentionally execute tasks incorrectly to ensure graders and cadre fully understand the
standards and are able to properly assess Candidates. The NCOICs for each specific event and lane
should be present for this process as their personnel are certified.
3-7. All graders and cadre need to demonstrate to the EIB Board their ability to perform
all required actions to standard within their event or lanes in order to be considered qualified.
Personnel who successfully accomplish this are considered to be certified for that EIB iteration only.

EIB TRAIN-UP
3-8. The EIB train-up typically occurs one week prior to the EIB test, unless a unit has established
an alternate test schedule as outlined in section 2-3 of this publication.
3-9. The train-up period consists of five days of instructional training of all tasks selected by the
EIB Board, to include practice land navigation lanes. This training can be centralized on the actual
EIB site or conducted in a decentralized manner at the company level at the discretion of the EIB
Board. This is the only train-up period specifically required for EIB testing; however, units should
not rely on this train-up phase alone.
3-10. While all lanes, stations, and test areas may be used for the train-up phase at the discretion
of the EIB Board, conditions within the Individual Tactical Test (ITT) lanes need to be significantly
altered prior to the actual EIB test to ensure Candidates do not know what to expect when testing
at each lane. When altering the scenarios for the lanes, the following actions should be incorporated
Page: 27

at a minimum: Operations Order, call signs, frequencies, sequence of tasks on the lane, location of
opposition forces, changing wound location or type of wound for first aid, change target locations
and the OT factor for the call for fire, and any other conditions that create a situation where the
Candidate will be forced to react for the first time when being evaluated on the lanes. These changes
should be incorporated into the initial concept plan when the EIB Board is formed.
3-11. During the train-up phase Candidates are permitted to use the existing land navigation site
that will be used for testing; however, lanes and points need to be changed for the actual EIB test.
All efforts and control measures need to be put in place to ensure Candidates are not testing on the
same lanes they practiced on and are not able to create a cheat sheet for the course. Whenever
possible, lanes should be set aside for practice only with the understanding that those lanes will not
be used for testing.
3-12. During the train-up phase it is not necessary to use the graders or cadre as the primary
instructors on the training site. Emphasis should be placed on having team leaders and squad
leaders preparing and training their Soldiers for the test, with graders and cadre observing and
making corrections as needed. The EIB Board is responsible for ensuring that personnel tasked with
instructing Candidates at this point are knowledgeable and certified to instruct their specific tasks.
3-13. All required equipment and training aids should be present and in working condition for use
by Candidates during the train-up phase. Equipment requirements are dependent on the tasks that
the unit has selected for the ITT lanes and the number of Candidates they have testing. The primary
responsibility of the graders and cadre at this point is to ensure all tasks are being executed properly
according to the established conditions while addressing any issues, questions, or concerns from the
Candidates in regards to expectations and test requirements.
3-14. The train-up phase and testing must be completed within 12 concurrent days, with
the exception to the conditions outlined in section 2-3 of this publication. Personnel may be
given a two-day stand down period between the train-up and test phases at the discretion of the
Commander.
3-15. The EIB Board has the discretion to determine the manner in which the train-up phase
is conducted. For example, Candidates can conduct the train-up phase through round-robin
training, simulated lane execution, simulated missions, etc. The key to the train-up phase is that the
Candidates are left with no questions regarding the manner in which they will test and that all tasks
have been instructed in accordance with the specified conditions and standards.

TEST VALIDATION
3-16. Units should be prepared to have the Test Manager present during the last three days of the
train-up phase for the purpose of test validation and issuing of the Test Control Number (TCN);
however, this time frame is flexible and can be coordinated directly with the Test Manager based on
his availability determined by other units test schedules. Test validation may occur concurrently
with the train-up with minimal interference; however, during the validation, units have to have all
Page: 28

training areas, stations, and lanes constructed and accessible for the Test Manager.
3-17. During test validation units should be prepared to make slight adjustments to their
test execution plan based on input from the Test Manager, although maintaining open lines of
communication with the Test Manager during all test preparation will help minimize final changes
to the test execution. A TCN will only be issued after the Test Manager has validated the entire test
site.
3-18. Land navigation test lanes and ITTs will be off limits to all Candidates once the Test
Manager has validated those areas. Candidates may continue to have access to the APFT route, Foot
March route, MST stations, and practice land navigation lanes after Test Manager validation as these
test requirements are already a known factor to the Candidates.

TIME LINE
3-19. Using the following time line as a guide, with T-Day representing Test Day 1, units should be
prepared to execute EIB testing as follows:

T-7 Train-up Day 1

T-6 Train-up Day 2
T-5 Train-up Day 3
T-4 Train-up Day 4
T-3 Train-up Day 5
T-2 Commanders Time
T-1 Commanders Time
T-Day Test Day 1: APFT and Land Navigation
T+1 Test Day 2: MST Stations and ITT Lanes
T+2 Test Day 3: MST Stations and ITT Lanes
T+3 Test Day 4: MST Stations and ITT Lanes
T+4 Test Day 5: Foot March and Award Ceremony

3-20. While the entire EIB process is intended to be executed over 12 consecutive days, units
have the discretion to transition from Train-up Day 5 (T-3) directly into Test Day 1 (T-Day). The
Commanders Time reflected on T-2 and T-1 may be used at the discretion of the Commander.
While the formal train-up phase cannot be extended beyond five days, units may use the two days
of Commanders Time for study groups, Sergeants Time, refresher training, administrative time,
pass, etc. Without exception, testing will be conducted over five continuous days beginning with the
APFT on Test Day 1 and ending with the foot march on Test Day 5.
3-21. This time line reflects all Candidates conducting the APFT and land navigation in one mass
group on Test Day 1 (T-Day); however, the EIB Board may elect to break the Candidates down into
four groups on Test Day 1 after the APFT with groups rotating through the Land Navigation, MST
stations, and ITT lanes over Test Days 1 through 4 (T-Day through T+3).
Page: 29

Chapter 4

Phase 1 Army Physical Fitness Test

CONCEPT
4-1. The APFT is the first graded event of the EIB test. Candidates are required to perform pushups, sit-ups, and a two-mile run to standard in accordance with regulations. This is a GO or NOGO event which must be passed in order for a Candidate to remain in the EIB process. Previous
Record APFT tests cannot be used to waive participation in this event all Candidates will take the
APFT. There will be no re-test for any Candidates who fail this event. These conditions cannot be
waived.
4-2. Candidates testing for the EIB must score a minimum of 75 points in each event for their
age group in order to receive a GO for this phase. Personnel who have received a permanent profile
which requires them to take an alternate event are permitted to test in accordance with the guidance
established in section 2-22 through 2-24 of this publication.
4-3. This event constitutes Phase 1 of the EIB test and may only be graded by EIB Cadre
appointed by orders who have already been awarded the EIB - This cannot be waived. It is the
responsibility of the EIB Board to ensure all graders for this event are grading to the same standard
without variance. The EIB Board will establish this standard in accordance with existing regulations.
4-4. In order to improve the flow of Candidates through this phase in a more timely fashion,
as well as establish better control of personnel, it is recommended that Candidates are placed into
groups based on age. While units can allow Candidates to execute push-ups and sit-ups beyond
the 75 points requirement of their age group, they may also stop Candidates once the minimum
requirement of 75 points has been reached, as this will reduce the time required to test all
Candidates.
4-5. Releasing Candidates by age group for the two-mile run eliminates the need for graders to
record individual scores as Candidates cross the finish line, as the run can be terminated as soon as
the maximum allowable time for a specific age group has been reached. Candidates who cross the
finish line within the required time receive a GO for the two-mile run, while Candidates who fail to
finish in the required time can be directed to a different holding area to be processed for elimination
from the EIB test.
4-6. Units should ensure that the APFT site complies with current regulations; is well lit to
facilitate grading and control; that the two-mile run route is clearly marked; that adequate numbers
of medical personnel and water are on site; that adequate numbers of safety vehicles are available;
and proper risk management has been incorporated into the event.

Page: 30

Chapter 5

Phase 2 Land Navigation

CONCEPT
5-1. Land navigation is the second graded event of the EIB test. Day and night iterations will
be executed on Test Day 1 and may continue through Test Day 4 if the unit is executing a modified
time line based on rotating four groups of Candidates through the event. This phase will be
conducted in accordance with FM 3-25.26 and the additional guidance established in this chapter.
During this phase Candidates will demonstrate their individual proficiency in navigating from one
point to another while dismounted without the aid of electronic navigation devices. Candidates
must pass both day and night land navigation iterations in order to receive a GO for this event. This
event is not re-testable.
5-2. This event constitutes Phase 2 of the EIB test and may only be graded by EIB Cadre
appointed by orders who have already been awarded the EIB - this cannot be waived. It is the
responsibility of the EIB Board to ensure all graders for this event are grading to the same standard
without variance. The EIB Board will establish this standard in accordance with existing regulations.

Candidate CONDITIONS
5-3. Candidates will complete both day and night iterations while carrying their individual
weapon and wearing their individual combat equipment, to include adequate water, based on unit
SOPs governing dismounted combat patrols. Requests to modify this requirement should be routed
through the Test Manager with supporting justification to allow uniform modification.
5-4. Candidates will be provided a 1:50,000-scale military topographic map, a lensatic compass,
a coordinate scale and protractor (GTA 05-02-012), a writing instrument, a score sheet, and a list
of designated points that they have to find. Units should ensure that a compass calibration site has
been established for the Candidates to verify the accuracy of their compass before they begin the land
navigation course.
5-5. Candidates will be checked prior to beginning the land navigation course to ensure they have
no cell phones, GPS devices, or other electronic media or equipment that may be used to assist them
during this phase of testing.

NAVIGATION COURSE CONDITIONS

5-6. The navigation course utilized for testing must have had all points validated through a site
survey conducted by an Engineer or Field Artillery unit. If a unit is unable to use a validated course,
or unable to obtain Engineer or Field Artillery support in order to validate a new course, validation
Page: 31

may be accomplished by using approved military issued GPS devices as follows:

a. Use a minimum of two GPS devices to obtain a minimum of a ten-digit grid for each
point, to include start points, with no more than a 20 meter variance between readings from
each device.
b. All GPS devices used in the validation of the course must be the same model. For
example, using a DAGR and a PLUGR together in order to validate a course would not be
acceptable due to the accuracy differences of each different model.
c. Courses will not be validated with civilian GPS models under any circumstances.
5-7. The EIB Board is responsible for certifying the navigation course prior to the start of the
train-up phase. Certification differs from the validation process and consists of having designated
EIB cadre negotiate each lane of the course in order to confirm the following; all points are present
in the designated locations; each point is in good condition and has a reasonable expectation of being
located; and that the validation parameters from previous surveys remain in effect.
5-8. Navigation course must be equipped with orienteering punches at all points to ensure
Candidates were physically at their points.
5-9.

Day and night navigation lanes will consist of a start point and four navigation points.
a. Start points must be located on a boundary of the course along an accessible road with a
minimum distance of 150 meters between start points.
b. Start points will not be used as end points for any lane.
c. All navigation points must be located inside the boundaries of the navigation site.

5-10. The distance between navigation points during day navigation will be no less than 800
meters and no more than 1000 meters. The overall distance of a navigation lane during day
navigation will not exceed 4500 meters total. The 4500 meter total includes the distance traveled
from the Release Point to the Start Point and from the final navigation point to the End Point, where
score sheets are collected and a Candidates time is recorded.
5-11. The distance between navigation points during night navigation will be no less than 600
meters and no more than 800 meters. The overall distance of a navigation lane during night
navigation will not exceed 3500 meters total. The 3500 meter total includes the distance traveled
from the Release Point to the Start Point and from the final navigation point to the End Point, where
score sheets are collected and a Candidates time is recorded. At the discretion of the EIB Board,
navigation points may be marked at night with reflective material and/or light sticks.
5-12. Self-correcting navigation courses are permissible for use during EIB testing; however, start
points for the day iteration will not have any identifying grid locations on them.
Page: 32

5-13. Day navigation will be conducted after sunrise and before End of Evening Nautical Twilight
(EENT) for the region that testing is conducted in. Night navigation will be conducted after EENT
and before sunrise for the region that testing is conducted in.

DAY NAVIGATION TEST STANDARDS

5-14. The following standards will apply for all Candidates conducting the day navigation course:
a. Candidates will be given instructions to locate their start point utilizing their pace count
and terrain association techniques.
b. Candidates will stage at a known release point after they have received their start points,
course orientation brief, and safety brief. At the direction of the navigation course NCOIC,
Candidates will be given the signal to start and official timing will begin. Units may utilize
a staggered release plan in order to provide better control and reduce congestion within the
navigation course.
c. Upon locating their start point, Candidates will record the six-digit grid location with grid
zone identifier for their assigned start point on their score sheet. The grid location provided
by the Candidate must be within 100 meters of the actual location. A six-digit grid is the
ONLY acceptable format for this requirement.
d. Candidates will record the alpha numeric identification for each of their navigation points
as well as punching their score card with the unique punch provided at each point. Grid
locations will be provided in six or eight-digit format based on guidance from the EIB Board.
e. Candidates will have two hours to correctly locate three out of four of the navigation
points on their lane, return to the end point, and report to the designated EIB cadre. Upon
reporting to the EIB cadre the Candidates completion time will be recorded on the score
card. At this point Candidates will be considered as having completed their attempt for the
day navigation course and will not be permitted to re-enter the course, even if they have
returned before their allotted time has expired.
f. Candidates will receive a NO-GO for day navigation under the following circumstances:
(1) Submitting the location of their start point in anything other than a six-digit
grid.
(2) Failing to provide the grid zone identifier for their start point.
(3) Submitting a grid location for their start point which is off by more than 100
meters.
(4) Failing to find and properly record at least three of their navigation points.
Page: 33

(5) Failing to properly punch their score card for each navigation point.
(6) Failing to complete the course in two hours or less.
(7) Not having their map or score card with them when reporting to the end point.
g. Candidates who receive a NO-GO on the day navigation course will be eliminated from
the EIB process.

NIGHT NAVIGATION TEST STANDARDS

5-15. The following standards will apply for all Candidates conducting the night navigation course:
a. Candidates will be provided their start point location for the night navigation course.
There is no requirement for them to provide the grid location of their start point.
b. Candidates will stage at a known release point after they have received their start points,
course orientation brief, and safety brief. At the direction of the navigation course NCOIC,
Candidates will be given the signal to start and official timing will begin. Units may utilize
a staggered release plan in order to provide better control and reduce congestion within the
navigation course.
c. Candidates will record the alpha numeric identification for each of their navigation points
as well as punching their score card with the unique punch provided at each point. Grid
locations will be provided in six or eight-digit format based on guidance from the EIB Board.
d. Candidates will have two hours to correctly locate three out of four of the navigation
points on their lane, return to the end point, and report to the designated EIB cadre. Upon
reporting to the EIB cadre the Candidates completion time will be recorded on the score
card. At this point Candidates will be considered as having completed their attempt for the
night navigation course and will not be permitted to re-enter the course, even if they have
returned before their allotted time has expired.
e. Candidates will receive a NO-GO for night navigation under the following circumstances:
(1) Failure to find and properly record at least three of their navigation points.
(2) Failure to properly punch their score card for each navigation point.
(3) Failure to complete the course in two hours or less.
(4) Not having their map or score card with them when reporting to the end point.

Page: 34

f. Candidates who receive a NO-GO on the night navigation course will be eliminated from
the EIB process.

Page: 35

Chapter 6

Phase 3 Master Skills Testing

CONCEPT
6-1. Master Skills Testing (MST) is used to evaluate a Candidates proficiency with weapon
systems and their associated tasks common to an Infantry unit. MST is executed in conjunction
with the Individual Tactical Test (ITT) lanes and is performance based. Candidates are required to
execute each task to an established set of standards within a specified period of time. Candidates
must pass one MST station each day prior to testing on an ITT lane for that specific day. Each MST
station will consist of three individual test points. Candidates who fail to meet the standards for
MST will be eliminated from the EIB process without attempting an ITT lane.
6-2. Master Skills Testing consists of the following weapons and associated tasks, which are
organized as follows:
MST Station 1
Test Point 1 M16 Rifle or M4 Carbine
Test Point 2 M249 Squad Automatic Weapon
Test Point 3 MK-19 40mm Grenade Launcher
MST Station 2
Test Point 4 M9 9mm Pistol
Test Point 5 M240B Machine Gun
Test Point 6 Prepare a Range Card for the M240B Machine Gun
MST Station 3
Test Point 7 M203 or M320 40mm Grenade Launcher
Test Point 8 M136 Launcher
Test Point 9 M2 or M2A2 Caliber .50 Machine Gun
6-3. Units may request substitution of a different weapon system for MST testing in order to
accommodate special weapons that may be part of the unit MTOE, or may be required for a units
specific mission. If substitution is approved by the Test Manager, the unit will be required to
develop specific tasks, conditions, and standards for that weapon system in acoordance with current
regulations and doctrine. These standards must be similar to those contained in Appendix B of this
pamphlet. These standards must be reviewed by the Test Manager and approved for use by the Chief
of Infantry.

Page: 36

CONDITIONS
6-4. MST Testing is executed concurrently with the ITT lanes. Units may establish the MST
stations in an area separate from the ITT lanes or pair the three MST stations with the three ITT
lanes. If the MST stations are paired with the ITT lanes, there should be enough distance from the
lanes to prevent Candidates from observing lane testing. In order to facilitate Candidate throughput,
units should plan on establishing the same number of sub-stations for MST testing as they have
established for the ITT Lanes.
6-5.

Each MST station or sub-station should be established with the following at a minimum:
a. Authorized stopwatch for timing Candidates.
b. All required weapon systems and equipment.
c. Adequate overhead cover and ground cloth if needed.
d. Dividers that prevent Candidates from observing each other while testing and prevent
Candidates from being able to observe MST testing from the holding areas.
e. Tables, if used, should be sturdy enough to support the weapon systems and any actions
that Candidates have to take during testing with the weapons.

TESTING
6-6. On Test Days 2 through 4 (T+1 through T+3), Candidates will assemble in their appointed
holding area for that specific day and wait for their turn to attempt their MST station for that day.
6-7. Training on actual weapon systems are not permitted inside the holding areas. At the
discretion of the EIB Board, practice and study areas may be designated outside of holding areas for
this purpose.
6-8. The uniform for MST testing is the same uniform designated for the ITT lanes, and at a
minimum should consist of the ACH, current issued load bearing TA-50, water, and individual
weapon. The EIB Board is responsible for establishing the uniform requirements for all phases of
testing.
6-9. Upon instruction from the EIB cadre, Candidates will proceed from the holding area to the
MST station. Once the Candidate arrives at the MST station, the grader will state the following:

I am (Rank and Name) and will be your grader for MST Station (insert station number
1, 2, or 3). During this phase of testing you will be evaluated on the following: (insert the three
weapon systems for the test points). Do you have any questions before you begin?
Page: 37

After this introduction the grader will provide additional guidance to the Candidate in regards
to positioning himself at the test points, as well as the placement of any individual equipment if
needed.
6-10. Graders must read all tasks, conditions, and standards to the Candidate prior to beginning
each test point from the script provided for each event. All MST tasks will be conducted in
accordance with the conditions and standards listed in Appendix B of this publication. Appendix
B has been designed to allow units to readily reproduce the tasks, conditions, and standards for use
during EIB training and testing.
6-11. Grading of all MST tasks will be conducted in accordance with Chapter 2, Section 2-25,
subparagraph (c) of this publication.

Page: 38

Chapter 7

Phase 4 Individual Tactical Test Lanes

CONCEPT
7-1. This phase of the EIB test requires Candidates to successfully negotiate three test lanes over
the course of Test Days 2, 3, and 4 (T+1 through T+3), while demonstrating their tactical and
technical proficiency as an Infantryman. Candidates must meet the MST requirements for the test
day before being allowed to attempt an Individual Test (ITT) lane.
7-2. These test lanes are constructed and executed in a similar manner as Squad Tactical Exercise
(STX) lanes; however, are focused on individual skill level one tasks. Based on this requirement, lane
scenarios should be designed around the concept that they will be executed by a single Candidate
employing skill level one capabilities, regardless of rank. Under no circumstances will collective
tasks, in whole or part, be incorporated into the ITT lanes.
7-3. ITT lanes are scenario driven and should incorporate stressors and conditions that force
Candidates to constantly adapt to changing situations while attempting to achieve a successful overall
outcome of a simulated Infantry mission within a specified time frame. Candidates will be required
to complete a series of individual tasks tactically, to acceptable standards, while the environmental
conditions are changed.
7-4. The purpose of the ITT lanes is to conduct an overall evaluation of a Candidates ability to
react, adapt, and think through unexpected situations as they continue to accomplish their assigned
mission through successful employment of individual skills to established standards.
7-5. Grading of the ITT lanes are conducted in accordance with Chapter 2, Section 2-25, subparagraph (d) of this publication. ITT lanes are not re-testable.

LANE REQUIREMENTS
7-6. The three ITT lanes will incorporate 10 overall tasks per lane, for a total of 30 testable tasks,
which include all applicable sub-tasks.
7-8. While units have the latitude to create their own scenarios, the following core tasks must be
incorporated into the ITT lanes:
a. Call for Fire Executed in accordance with Conditions and Standards in Appendix D.

Must utilize a Grid Mission

Must demonstrate proficiency in applying the Observer/Target Factor
Must shift fire from a known point after initial engagement
Page: 39

Must incorporate range estimation

b. Move under direct fire employing Individual Movement Techniques.

c. Request medical evacuation utilizing the 9-line format.
d. Submit and Send a Spot Report (SPOTREP).
e. Employ and identify Hand Grenades.
Hand grenade identification may occur just prior to beginning the lanes when
conducting pre-combat checks.
When provided with two practice fragmentation grenades, a Candidate must engage
a target 35 meters away, with at least one grenade landing within five meters of the
target.
Candidates are only permitted two attempts at passing this event utilizing the
two grenades they are issued. Candidates are not permitted to pick up additional
grenades on the ITT lanes for this task.
f. First Aid: A minimum of three of the following first aid tasks must be included in the ITT
lanes (one task per lane); however, units may include more than three first aid tasks if they
choose.

Apply Pneumatic Splint to a Casualty with a Suspected Fracture of an Extremity

Request Medical Evacuation
Evaluate a Casualty (Tactical Combat Casualty Care)
Perform First Aid to Clear an Object Stuck in the Throat of a Conscious Casualty
Perform First Aid to Prevent or Control Shock
Perform First Aid for Burns
Perform First Aid to Restore Breathing and/or Pulse
Perform First Aid for an Open Abdominal Wound
Perform First Aid for a Bleeding and/or Severed Extremity
Perform First Aid for an Open Head Wound
Perform First Aid for a Suspected Fracture
Transport a Casualty
Insert an Oropharyngeal Airway (J Tube)
Perform a Needle Chest Decompression
Control Bleeding
Apply a Tourniquet to Control Bleeding
Apply a Hemostatic Dressing

g. Operate a SINCGARS or ASIP radio.

7-9. After determining how the required core tasks will be incorporated into the ITT lanes, units
may select the remaining tasks from the approved task list in Appendix C. The EIB Board must
Page: 40

ensure that the selected tasks incorporate the concepts of Shoot, Move, Communicate, Sustain, and
Survive in some fashion throughout their three lanes. When creating scenarios for the ITT lanes, the
EIB Board should ensure that the tasks for each lane properly support the scenarios they are paired
with.
7-10. Performance measures for all tasks can be accessed through the following link: https://www.
atn.army.mil/. For testing continuity throughout the Army, this is the only authorized source for
obtaining performance measures. If the EIB Board identifies a discrepancy with information on
the site they should contact the Test Support Officer for a ruling. If the information contained
on the site is incorrect or outdated, the Test Manager will determine which source will be used for
establishing performance measures for the test.
7-11. Candidates will only be graded once for each task. Tasks may not be repeated throughout
the ITT lanes for the purpose of fulfilling EIB grading requirements; however, tasks from one lane
may be incorporated into another lane in order to support the scenario in a more realistic manner. If
a unit chooses to do this, the duplicated tasks will only be graded on one ITT lane and considered an
ungraded requirement in the other lanes, which are then subject to AAR comments from the grader.
This does not permit Candidates to perform duplicated tasks in an unacceptable manner which
could result in catastrophic failure as defined in Chapter 2, Section 2-25, sub-paragraph (d), subsection (2) of this publication.
7-12. The EIB Board should ensure that the lane scenarios contain viable decision points which
require a Candidate to make a decision after evaluating the situation under stress. Decision points
should be kept in line with typical expectations of a skill level one Soldiers abilities. While decision
points are not graded events within the EIB test, they are subject to AAR comments from the grader;
however, this does not permit Candidates to perform these actions in an unacceptable manner which
could result in catastrophic failure as defined in Chapter 2, Section 2-25, sub-paragraph (d), subsection (2) of this publication.
7-13. ITT lanes will be a minimum of 150 meters, but no more than 250 meters long. Lanes
should be wide enough to ensure all individual movement and task execution can occur to standard.
Lanes do not need to be linear in nature, and may follow existing terrain features or change
directions in any manner that the EIB Board determines best meets the intent of the scenarios. If
units are using sub-lanes to facilitate throughput, adequate control measures should be used to
prevent one sub-lane from encroaching on another.
7-14. Candidates will have 20 minutes to complete each lane. If the EIB Board feels that a lane
cannot be successfully completed within this time frame, they may request a waiver to allow them
to extend the time to no more than 30 minutes. Time constraints should be driven by performance
standards and not adjusted in order to simply provide more time for Candidates to complete a lane.
In addition, any request for an increase in time should take into consideration the impact it will have
in regards to Candidate throughput.

Page: 41

TESTING
7-15. In order to expedite Candidate throughput, units may elect to read the Operations Order for
the ITT lane to all of the Candidates at the same time while they are in the holding area waiting to
start MST testing. After completing the MST requirement for the specific test day, Candidates will
assemble in their appointed holding area for that specific day and wait for their turn to attempt their
ITT lane for that day. Holding lanes should be a sufficient distance from the actual lane in order to
prevent Candidates from being able to observe testing.
7-16. Training is not permitted inside the holding areas. At the discretion of the EIB Board,
practice and study areas may be designated outside of ITT holding areas for this purpose.
7-17. At a minimum, the uniform for the ITT lanes will consist of the ACH, current issued load
bearing TA-50, water, and individual weapon. The EIB Board is responsible for establishing the
uniform requirements for all phases of testing.
7-18. Upon instruction from the EIB cadre, Candidates will proceed from the holding area to the
initial staging point for the ITT lane. At this point the grader will state the following:

I am (Rank and Name) and will be your grader for the (insert ITT lane designation Lane
1, Lane 2, etc.). During this phase of testing you will be evaluated on your tactical execution of the
lane. Do you have any questions before you begin?
7-19. After the introduction, the grader will read the Operations Order for the lane if it has not
already been read to the Candidate in the holding area. The Operations Order cannot identify any
of the tasks that the Candidate will be required to execute and should be read in the same manner as
real Operations Order would be. Candidates are responsible for recording all relevant information
in regards to the mission, to include: enemy situation; friendly forces; call signs; frequencies;
medical evacuation requirements; etc. This will create a situation similar to combat operations in
that a Candidate will have to employ the proper skills, actions, and decisions when situations are
encountered on the lane. As the lane scenario unfolds, the Candidates ability to function under
stress while making the appropriate decisions in a tactical environment will be evaluated.
7-20. Candidates will be offered the opportunity to ask questions concerning the mission and
clarify any points of confusion or misunderstanding. Graders are permitted to answer these
questions in the same manner they would be answered during a real mission brief; however, the
graders cannot disclose any information concerning the tasks they will be required to perform.
7-21. After being offered the opportunity to ask questions, the Candidate will be given any
additional equipment that will be required for the mission for example; radio, grenades, first aid
equipment, binoculars, etc.
7-22. After receiving any special equipment required for the lane, Candidates will perform their
pre-combat checks. Pre-combat checks are not graded; however, are subject to AAR comments
from the grader. If a Candidate fails to perform their pre-combat checks to standard, they open
Page: 42

themselves to possible catastrophic failure as defined in Chapter 2, Section 2-25, sub-paragraph (d),
sub-section (2).
7-23. Graders will not give any indication of a Candidates performance once the pre-combat
checks begin, and will remain silent in this regard until conclusion of the lane.
7-24. Once a Candidate completes their pre-combat checks and moves from the staging area onto
the graded portion of the lane, they will be considered to have crossed the line of departure. Once
the line of departure has been crossed, timing for the lane will begin.
7-25. If a Candidate forgets to bring any of their equipment with them when they cross the line of
departure, they will not be permitted to go back and retrieve it. If the forgotten equipment prevents
them from accomplishing a required task, or results in a catastrophic failure, the Candidate will
receive a NO-GO for the task, and possibly the entire lane.

Page: 43

Chapter 8

Phase 5 Foot March

CONCEPT
8-1. The final phase of the EIB test is the 12-mile foot march and the successful completion of the
weapons proficiency skills test. The foot march is executed in accordance with the guidance listed in
this publication and FM 21-18. The foot march may be executed during the day or at night at the
discretion of the EIB Board and the unit commander. All Candidates must successfully complete
the foot march within the prescribed time line and conditions. Candidates must pass the foot march
and weapons proficiency skills test to receive a GO for this event. The foot march and the weapon
proficiency test is a GO or NO-GO event and is not re-testable.

REQUIREMENTS
8-2. The foot march route must be 12-miles in length and will be clearly marked and easily
identifiable by the Candidates. The length of the route should be verified through the use of a
calibrated distance measuring wheel. If a calibrated measuring wheel is not available then the course
can be verified by using the average odometer reading taken from three different vehicles.
8-3. Route selection should include consideration for ease of movement, consistent terrain
features, and no obstructions along the route that would require the Candidates to maneuver
around. The slope of the terrain should be similar in nature to the terrain that the Candidates had
been conducting their conditioning and training on.
8-4. If the route requires a turn-around point, this point should be easily recognizable by the
Candidates, allow for Candidates to turn around without impeding each other or causing congestion
at the turn-around point that would slow the individuals rate of march. In addition, units need to
establish positive controls along the route, as well as at any turns or turn-around points, to ensure
Candidates actually remain on the route and do not attempt to bypass control points or EIB cadre.
8-5. Water points need to be established along the route with reasonable distance between each
water point. As a general guide, water should be available between every three to four miles along
the route.
8-6. Units should take every effort to plan the foot march along a route closed to vehicular traffic;
however, if this is not possible, positive safety controls need to be put in place to ensure Candidates
are protected from vehicles.
8-7. Units should ensure there is at least one official timing device which has been calibrated for
the foot march, although it is recommended that two calibrated timers are used in the event one
fails. While it is not required, units are encouraged to provide the Candidates with the elapsed time
Page: 44

when they reach the six-mile point of the foot march. The time from the official clock will be the
only time used to officiate this event.
8-8. Units should ensure that medics are stationed along the route, ambulances are available, and
that safety vehicles are used along the route during this event.
8-9. Candidates may be cheered on and encouraged by others, as well as be paced by another
Candidate or Soldier; however, they cannot receive any form of assistance during the 12-mile foot
march (lifted, carried, picked up, given a ride in a vehicle, etc.). Candidates who receive assistance or
leave the approved route will receive a NO-GO for this event.
8-10. Candidates may be handed hydrating beverages by others, share canteens, and consume food
while executing the foot march. While this is an individual event, Candidates my move together in
a group if they choose, although each Candidate is responsible for establishing a pace that will allow
them to successfully complete the foot march within the prescribed time frame. Candidates are also
permitted to establish their own rest plan during this event.
8-11. Candidates must carry 35-pounds of dry weight in their ruck-sack over the entire course of
the foot march. This weight is in addition to their personal equipment and water, which is worn
and carried evenly distributed over their bodies. Units should have a calibrated scale at the end of
the course to ensure that the Candidates finish the event with the required weight in their ruck-sack.
Any Candidate who finishes with less than the required 35-pounds of dry weight in their ruck-sack
will be eliminated from the EIB process, even if they completed the foot march within the required
time.
8-12. Candidates must complete the foot march in three hours or less. Immediately crossing the
finish line, Candidates report to the weapon proficiency point. Candidates must correctly clear
and disassemble an M16-Series Rifle / M4 Series Carbine within two minutes. Candidates must
correctly assemble and perform a function check in sequence within two minutes to receive a GO for
this event.
8-13. The weapons proficiency test must be administered immediately after the Candidate crosses
the finish line for the 12 mile foot march. Candidates who finish the foot march early may be
permitted to rest and recover before the three hours expires at the discretion of the EIB Board. If
a Candidate fails the weapons proficiency test, they will receive a NO-GO for this event. The foot
march and the weapons proficiency test is a GO or NO-GO event and is not retestable.

UNIFORM
8-13. The foot march must be executed in the ACU uniform with approved boots. In addition
to the ACU uniform, Candidates will are also required to have the following at a minimum: ACH,
issued TA-50 load carrying equipment, (2) 1-quart canteens, soft cap, M4, and ruck-sack. Units
may add any additional equipment to this per unit SOP or at the direction of the EIB Board and
Commander.
Page: 45

Chapter 9

Awarding the Expert Infantryman Badge and Streamer

CRITERIA
9-1. Candidates who meet all of the eligibility requirements outlined in AR 600-8-22 and
Chapter 2 of this publication are eligible for award of the Expert Infantryman Badge, Expert
Infantryman Badge Certificate, and award orders after successfully passing all five phases of the EIB
test.
9-2. Units should ensure that the awarding of the Expert Infantryman Badge occurs during
a suitable public ceremony as soon as possible after receiving award orders and certificates from
USAIS. Units may request approval to conduct a provisional award ceremony in advance of
receiving orders to be conducted upon completion of phase five of the EIB test (12-mile foot march)
through the Test Manager.
9-3. Commanders above company level who exercise General courts martial authority over
eligible recipients of the EIB are authorized to submit a formal request through the Chief of
Infantry that the EIB be awarded to all eligible personnel who successfully passed the EIB test.
Announcement for the award of the EIB is in accordance with AR 600-8-105 (Military Orders), and
should cite AR 600-22, Paragraph 8-9 and USAIS PAM 350-6 as the appropriate authority for the
award.
9-4. To ensure standardization throughout the Army, units are required to present the USAIS
EIB certificate as the official certificate to accompany the badge and orders; however, units may
also award a certificate of their own design in addition to the USAIS certificate if they choose. For
tracking and verification purposes, the corresponding order number from the orders will be recorded
on the EIB certificate by USAIS.
9-5. It is the responsibility of the awarding unit to ensure individual Enlisted and Officer Records
Briefs are properly updated to reflect the award of the EIB, as well as ensuring a copy of the orders
are uploaded into each recipients iPERMS file.

EXPERT INFANTRY STREAMER

9-6. In accordance with AR 600-8-22, paragraph 7-4, the Expert Infantry Streamer is awarded to
an Infantry company; Infantry Battalion; Infantry Brigade; or a separate Infantry platoon when at
least 65 percent of the assigned strength has earned the EIB during an EIB testing period.
9-10. Once awarded, the receiving unit can display the Expert Infantry Streamer for a period of 12
months on their unit colors or guidon. The Streamer must be removed at the end of the 12 month
period from when it was awarded.
Page: 46

9-11. The Expert Infantryman Streamer consists of the following:

Size: The Expert Infantry Streamer measures 1 inch wide by 24 inches long (from
the flagstaff to the end of the swallowtail) with a 1 1/2inch fork. This streamer must
be ordered and purchased through the individual unit supply channel from either the
GSA catalog or utilizing other local purchase options.
Color: The Expert Infantry Streamer is white with blue embroidered lettering
indicating the level of recognition as follows:

Expert Infantry Brigade

Expert Infantry Battalion
Expert Infantry Company
Expert Infantry Platoon

9-12. Commanding Generals may award the Expert Infantry Streamer to separate Infantry
Brigades, Battalions, or Platoons under their command.
9-13. Commanders of Infantry Battalions or Brigades may award the Expert Infantry Streamer to
Infantry Companies under their command.
9-14. When awarding the Expert Infantry Streamer, Commanders should cite this publication as
the appropriate authority for the award.

Page: 47

Chapter 10

Post Test Requirements

AFTER ACTION REPORT
10-1. Units are required to submit an After Action Report (AAR) within four weeks of completion
of the EIB process utilizing the format provided by the Test Support Officer (Test Manager). The
AAR must include the Standard Name Line information for all personnel who passed the EIB test
and are eligible for award of the EIB. The Chief of Infantry will not issue any award orders or
certificates until the AAR has been received by the Test Manager.
10-2. Submission of all AARs should be e-mailed and sent to the Test Manager at the U.S. Army
Infantry School, Fort Benning, Georgia.
10-3. Outside of award recipients, information from the AARs will only be used for statistical
purposes in regards to training and identifying trends across the force. In addition, the AAR
information will assist in determining the relevancy of the EIB process and aid in making updates to
the test process as needed.
10-4. Under no circumstances will AAR information be used in assessing any unit or command
capabilities, as the EIB process is designed to test individual abilities only. All AAR information
will remain in the U.S. Army Infantry School, and when statistics are being used to address training
trends, all individual unit references will be removed from the aggregate information.
10-5. Due to the high level of training, planning, and logistical support involved in the EIB
process, units are encouraged to conduct an internal AAR to assist them with future training and
operations.
10-6. It is highly recommended that units retain all EIB materials upon completion of the test
process in order to establish continuity for future EIB tests conducted within the unit. Units
who conclude the EIB process are encouraged to continually share information with other units
concerning the EIB test.
10-7. Units are encouraged to provide input to the U.S. Army Infantry School in regards to
the EIB to assist in making the test more relevant while preserving the integrity of the Expert
Infantryman Badge.
10-8. Any unresolved issues that were identified during the EIB process by either the Test Manager
or the unit should be addressed and resolved during this period, either through the Test Manager or
the Chief of Infantry.
10-9. Commanders should follow up with their appropriate S-1 staff to ensure that the records for
all Soldiers who received the EIB were properly updated to reflect this award.
Page: 48

GLOSSARY OF TERMS
AA
AAR
AAR
ACU
ANCD
AO
APFT
AR
ARNG
ASP
ATN
ATTP
CB
CBRN
CLS
CMF
CSM
EFMB
EIB
EOM
FBCB2
FDC
FH
FM
FPL
GPS
GTA
IAW
ICAM
ICM
IED
IOT
ITT
IVO
JLIST
LD
LOA
MACOM
MAR2
MBITR
ME
MELIOS

Assembly Area
After Action Report
After Action Review
Army Combat Uniform
Automated Net Control Device
Area of Operation
Army Physical Fitness Test
Army Regulation
Army National Guard
Ammunition Supply Point
Army Training Network
Army Doctrine and Training Procedures
Chemical, Biological
Chemical, Biological, Radiological, and Nuclear
Combat Life Saver
Career Management Field
Command Sergeant Major
Expert Field Medical Badge
Expert Infantryman Badge
End of Mission
Force XXI Battle Command Brigade and Below
Fire Direction Center
Frequency Hopping
Field Manual
Final Protective Line
Global Positioning System
Graphic Training Aid
In Accordance With
Improved Chemical Agent Monitor
Improved Conventional Munitions
Improvised Explosive Device
In Order To
Individual Tactical Test
In Vicinity Of
Joint Lightweight Integrated Suit Technology
Line of Departure
Line of Accounting
Major Army Command
Medical Retention Review
Muilti-Band Inter/Intra Team Radio
Main Effort
Mini Eyesafe Laser Infrared Observation Set
Page: 49

GLOSSARY OF TERMS
MMRB
MOPP
MOS
MST
NCO
NCOIC
NCS
OBJ
OT
PAM
PCC
PDF
PLGR
RETS
ROTC
SALUTE
SE
SINCGARS
SKL
SMCT
SME
SOP
SPOTREP
SQD
STX
TACSOP
TAMIS
TCN
TDY
TM
TSO
USAIS
USAR

Medical Retention Board

Mission Orientated Protective Posture
Military Occupational Specialties
Master Skills Test
Non-Commissioned Officer
Non-Commissioned Officer in Charge
Net Control Station
Objective
Observer Target
Pamphlet
Pre Combat Checks
Principal Direction of Fire
Precision Lightweight Global (Positioning System) Receiver
Remote Target System
Reserve Officer Training Corps
Size, Activity, Location, Unit, Time, and Equipment
Supporting Effort
Single-Channel Ground and Airborne Radio Subsystem
Simple Key Loader
Soldiers Manual of Common Task
Subject Matter Expert
Standard Operating Procedure
Spot Report
Squad
Squad Tactical Exercise
Tactical Standard Operating Procedure
Total Ammunition Management Information System
Test Control Number
Temporary Duty
Tactical Manual
Test Support Officer
United States Army Infantry School
United States Army Reserve

Page: 50

APPENDIX A

References
WEB RESOURCES
The Army Training Network (ATN)

https://atn.army.mil
Army Publishing Directorate

http://www.apd.army.mil
USAIS EIB Website

http://www.benning.army.mil/infantry/eib
Infantry Publications, 7 Series, Army Doctrine and Training Publications

http://armypubs.army.mil/doctrine/7_series_collection_1.html
Weapons Publications, 23 Series, Army Doctrine and Publications

http://armypubs.army.mil/doctrine/23_series_collection_1.html
GTA 05-02-012, Coordinate Scale and Protractor, 1 June 2008
https://atiam.train.army.mil

ARMY REGULATIONS
AR 335-15
AR 600-8-105
AR 600-9

Management Information Control System, 28 October 1986

Military Orders, 28 October 1994
The Army Weight Control Program, 27 November 2006

FIELD MANUALS
FM 3-22.9

FM 3-25.26

FM 7-22
FM 4-30.13

Rifle Marksmanship, M-16-/M4-Series Weapons, 12 August 2008

and Change 1, 10 February 2011
Map Reading and Land Navigation, 18 January 2005
and Change 1, 30 August 2006
Army Physical Readiness Training, October 2012
Ammunition Handbook: Tactics, Techniques, and Procedures for
Munitions Handlers, 1 March 2001

Page: 51

Expert Infantryman Badge

Test Scorecard

APFT - Group 1 - 17-21

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Score 75 points in the push-up, sit-up, and the two mile run event in accordance with regulations.
Performance Measures:
1. Conduct 53 repetitions of the push-up event within two minutes.
2. Conduct 63 repetitions of the sit-up event within two minutes.
3. Complete the 2 mile run under 14:48.

Pass

Passed Failed

Reason (s) for Failure:

Scorers Signature:
APFT Group 1

Fail

Date:
Ver 2.0

Previous Edition is Obsolete

Expert Infantryman Badge

Test Scorecard

APFT - Group 2 - 22-26

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Score 75 points in the push-up, sit-up, and the two mile run event in accordance with regulations.
Performance Measures:
1. Conduct 53 repetitions of the push-up event within two minutes.
2. Conduct 61 repetitions of the sit-up event within two minutes.
3. Complete the 2 mile run under 15:15.

APFT Group 2

Fail

Passed Failed

Reason (s) for Failure:

Scorers Signature:

Pass

Date:
Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

APFT - Group 3 - 27-31

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Score 75 points in the push-up, sit-up, and the two mile run event in accordance with regulations.
Performance Measures:
1. Conduct 53 repetitions of the push-up event within two minutes.
2. Conduct 59 repetitions of the sit-up event within two minutes.
3. Complete the 2 mile run under 15:36.

Pass

Passed Failed

Reason (s) for Failure:

Scorers Signature:
APFT Group 3

Fail

Date:
Ver 2.0

Previous Edition is Obsolete

Expert Infantryman Badge

Test Scorecard

APFT - Group 4 - 32-36

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Score 75 points in the push-up, sit-up, and the two mile run event in accordance with regulations.
Performance Measures:
1. Conduct 51 repetitions of the push-up event within two minutes.
2. Conduct 55 repetitions of the sit-up event within two minutes.
3. Complete the 2 mile run under 16:00.

APFT Group 4

Fail

Passed Failed

Reason (s) for Failure:

Scorers Signature:

Pass

Date:
Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

APFT - Group 5 - 37-41

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Score 75 points in the push-up, sit-up, and the two mile run event in accordance with regulations.
Performance Measures:
1. Conduct 49 repetitions of the push-up event within two minutes.
2. Conduct 52 repetitions of the sit-up event within two minutes.
3. Complete the 2 mile run under 16:30.

Pass

Passed Failed

Reason (s) for Failure:

Scorers Signature:
APFT Group 5

Fail

Date:
Ver 2.0

Previous Edition is Obsolete

Expert Infantryman Badge

Test Scorecard

APFT - Group 6 - 42-46

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Score 75 points in the push-up, sit-up, and the two mile run event in accordance with regulations.
Performance Measures:
1. Conduct 44 repetitions of the push-up event within two minutes.
2. Conduct 47 repetitions of the sit-up event within two minutes.
3. Complete the 2 mile run under 17:00.

APFT Group 6

Fail

Passed Failed

Reason (s) for Failure:

Scorers Signature:

Pass

Date:
Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Day Land Navigation

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Navigate from one point on the ground to another point while dismounted. (Day)
Performance Measures:
1. Determine the six digit grid with grid zone identifier of the starting stake to
within 100 meters.

Pass

Fail

Note: Grids without the grid zone identifier and or 8 digit grids or more are incorrect.

2. Correctly locate and record the identification as well as punching their score
card with the unique punch for at least 3 out of 4 points.
3. Perform performance measures 1 and 2 within 2 hours.

Note: Candidates that return missing their score card and or map will receive a No-Go.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
Day Land Navigation

Date:
Ver 2.0

Previous Edition is Obsolete

Expert Infantryman Badge

Test Scorecard

Night Land Navigation

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Navigate from one point on the ground to another point while dismounted. (Night)
Performance Measures:
1. Correctly locate and record the identification as well as punching their score
card with the unique punch for at least 3 out of 4 points.
2. Perform performance measure 1 within 2 hours.

Pass

Fail

Note: Candidates that return missing their score card and or map will receive a No-Go.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
Night Land Navigation

Date:
Previous Edition is Obsolete

Ver 2.0

Clear, Load, Reduce stoppage, Unload and Clear an M16-Series Rifle / M4 Series Carbine

Tasks:

1. Clear an M16-Series Rifle / M4 Series Carbine (In Sequence).

2. Load an M16-Series Rifle / M4 Series Carbine (In Sequence).
3. Correct malfunctions on an M16-Series Rifle / M4 Series Carbine (In Sequence).
4. Unload and clear an M16-Series Rifle / M4 Series Carbine (In Sequence).

Test Conditions:

Given an assembled M16-Series Rifle / M4 Series Carbine and a magazine loaded with four
blank rounds and one dummy, expended, or inert round.

Test Standards:

1. Within 30 seconds, clear, load, correct malunction, unload and clear an M16-Series Rifle /
M4 Series Carbine Carbine Rifle (In Sequence).

Note: Clearing the weapon is an integral part of unloading the weapon; the Candidate
must clear the weapon in order to pass this point.

Soldiers Manuel Crosswalk:

This task is based on task 071-COM-0028 Load an M16-Series Rifle / M4- Series Carbine,
071-COM-0033 Correct Malfunctions on an M16-Series Rifle / M4-Series Carbine, 071COM-0027 Unload an M16-Series Rifle / M4-Series Carbine, and 071-COM-0032 Maintain
an M16-Series Rifle / M4-Series Carbine. Performance measures can be found on https://atn.
army.mil.

Equipment Required for Station:

An M4 carbine with magazine; four blank rounds of ammunition (for each Candidate),
dummy, inert, expended, field table, clipboard, stopwatch, pencils, and EIB Form M4.2.

Site Setup:

Provide area on which to lay the M4 Carbine Rifle. Ensure the site affords a safe area for firing
blank ammunition. Also provide, at this site a container to collect expended blanks.

Page:

Instructions to Candidate:

Let me have your attention. At this point you must clear, load, correct a malfunction, and
unload and clear an M16-Series Rifle / M4 Series Carbine (In Sequence). You have received
an assembled M4 carbine and a magazine loaded with four blank rounds and one inert
round.
When I say Begin, you will load the clear ,load, and fire the M16-Series Rifle / M4 Series
Carbine until a stoppage occurs, apply immediate action, expend remaining ammunition,
then unload and clear the M16-Series Rifle / M4 Series Carbine, all within 30 seconds
(In Sequence). This tasks has been modified for EIB Do you understand what you must
do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause for five seconds and then say Begin.
Allow the Candidate to proceed for 30 seconds and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Clear, Load, Reduce Stoppage, Unload and Clear an M16-Series Rifle / M4 Series Carbine
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Clear an M16-Series Rifle / M4 Series Carbine (In Sequence).

2. Load an M16-Series Rifle / M4 Series Carbine (In Sequence).
3. Correct malfunctions on an M16-Series Rifle / M4 Series Carbine (In Sequence).
4. Unload and clear an M16-Series Rifle / M4 Series Carbine (In Sequence).
Performance Measures:

Pass

Fail

1. Clear an M16-Series Rifle / M4 Series Carbine (In Sequence).

a. Point the weapon in a safe diretion.

b. Attempt to place the selector lever on SAFE.

c. Remove the magizine from the weapon, if present.

d. Lock the bolt open.

e. Ensure that no ammunition is in the receiver and chamber.

f. Place the selector lever on SAFE.
2. Load an M16-Series Rifle / M4 Series Carbine (In Sequence).

a. Insert the magazine and push upward until the magazine catch engages

the magazine.

b. Tap upward on the bottom of the magazine.

c Depress the upper portion of the bolt catch.

d. Tap the forward assist to ensure that the bolt locks fully.
3. Perform immediate action on an M16-Series Rifle / M4 Series Carbine
(In Sequence).

a. Place the seletor lever on SEMI

b. Fire the weapon.

c. Slap upward on the magazine to ensure it seated fully.

d. Pull the charging handle to the rear, observe the ejection of the case or

cartridge, and check the chamber for obstruction.

e. Release the charging handle to feed a new round into the chamber.

f. Tap the forward assist.

g. Squeeze the trigger.

USAIS Form EIB M4, May 2014

Previous Edition is Obsolete

Ver 1.0

Expert Infantryman Badge

Test Scorecard

Clear, Load, Reduce Stoppage, Unload and Clear an M16-Series Rifle / M4 Series Carbine
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:
4. Unload and Clear an M16-Series Rifle / M4 Series Carbine (In Sequence).

a. Point the weapon in a safe diretion.

b. Attempt to place the selector lever on SAFE.

c. Remove the magizine from the weapon, if present.

d. Lock the bolt open (if not already open).

e. Ensure that no ammunition is in the receiver and chamber.

f. Press the upper portion of the bolt catch allowing the bolt to go forward.

g. Close the ejection port cover.

Pass

Fail

5. Conduct performance measures 1 through 4 within 30 seconds.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M4, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 1.0

Maintain M9 Pistol
Tasks:

1. Maintain an M9 Pistol.
2. Perform a function check on an M9 Pistol (In Sequence).

Test Conditions:

During daylight, given an M9 Pistol.

Test Standards:

1. Within 30 seconds, correctly clear (In Sequence) and disassemble the M9 Pistol.
2. Within 45 seconds, correctly assemble the M9 Pistol and perform a function check
(In Sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-COM-0001 Maintain an M9 Pistol, and 071-COM-0002

Perform a Function Check on an M9 Pistol. Performance measures can be found on https://
atn.army.mil.

Equipment Required for Station:

An M9 pistol for each Candidate, stopwatch, and EIB Form M9.

Site Setup:

Provide a flat surface for disassembly and assembly of the M9.

Page:

Instructions to Candidate:

Let me have your attention. At this point, you must perform operator maintenance on an
M9 Pistol and perform a function check (In Sequence) on an M9 Pistol. The purpose of this
is to determine your ability to perform operator maintenance on an M9 Pistol. You will show
the scorer that you can disassemble, assemble, and perform a function check on the weapon
(In Sequence). The weapon must pass a function check. You have 30 seconds to disassemble
the M9 Pistol. You may use only the equipment that you will find on the ground cloth beside
your weapon. Place the disassembled parts on the ground cloth as you remove them. Do you
understand what you
must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five for seconds and then say Begin.
Allow the Candidates to proceed for 30 seconds and then say Stop.
You now have 45 seconds to assemble the M9 Pistol and perform a function check
(In Sequence). You may use only the equipment found on the ground cloth beside your
weapon. Place the assembled weapon on the ground cloth after you complete the assembly and
function check. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for two minutes and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Maintain an M9 Pistol

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Maintain an M9 Pistol.

2. Perform a function check on an M9 Pistol (In Sequence).

Performance Measures:

Pass

Fail

1. Clear the M9 Pistol (In sequence).

a. Place the safety lever in the SAFE position.

b. Depress the magazine release button, and remove the magazine from the pistol, if
present.
c. Point the pistol in a safe direction.
d. Grasp the slide serrations and fully retract the slide to remove the chambered cartidge, if present.
e. Lock the slide to the rear using the slide stop.
f. Visually inspect the chamber to make sure it is empty.
g. Release the slide forward.
h. Ensure the safety lever is in the SAFE position.

2. Disassemble the M9 pistol (Do not grade in sequence)

a. Depress the slide stop and let the slide go forward.

b. Using your right hand, hold the pistol with the muzzle slightly raised.
c. Using your forefinger, press the disassemble lever button.
d. Rotate the disassembly lever downward until it stops.
e. Pull the slide and barrel assembly forward, and remove it from the receiver.
f. Slightly compress the recoil spring and sprain guide, simultaneously, lift them
up and remove them.
g. Separate the recoil spring from the spring guide.
h. Push in on the locking block plunger while pushing the barrel forward
slightly.
i. Lift and remove the locking block and battle assembly from the slide.

3. Perform performance Steps 1 and 2 within 30 seconds.

4. Assemble the M9 pistol (Do not grade in sequence)

a. Grasp the slide with the bottom facing up

b. Grasp the barrel assembly with the locking block facing up with the other hand.
c. Insert the muzzle into the forward end of the slide and simultaneously, lower the
rear of the barrel assembly by moving the barrel slightly downward with light thumb
pressure.
d. Insert the recoil spring guide into the recoil spring.
e. Insert the end of the recoil spring and the recoil spring guide into the recoil spring
housing and simultaneously, compress the recoil spring and lower the spring guide
until it is fully seated on the locking block cutaway.

USAIS Form EIB M9, May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Maintain an M9 Pistol

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

f. Push the firing pin block lever down.

g. Grasp the slide and barrel assembly with the sights up, and align the slide on the
receiver assembly guide rails.
h. Push until the rear of the slide is a short distance beyond the rear of the receiver
assembly and hold, simultaneously, rotate the disassembly latch lever upward.

5. Perform function check on an M9 Pistol (In sequence)

WARNING: Ensure the pistol is clear before you perform a functions check.
a. Place the safety lever in safe position.
b. Depress the slide stop.
c. Insert the empty magazine into the pistol.
d. Ensure that the magazine catch locks the magazine in place.
e. Retract the slide fully and release.

NOTE: the slide should lock to the rear.

f. Depress the magazine release button allowing the magazine to fall free.
g. Depress the slide stop and allow the slide to return fully forward.
h. Squeeze and release the trigger.
NOTE: The firing pin block should move up and down. The hammer should not
move.
i. Place the safety lever in the FIRE position
j Squeeze the trigger to check the double action.
NOTE: The hammer should cock and fall.
k. Squeeze the trigger again and hop it to the rear.
l. Manually retract and release the slide.
NOTE: You should hear a click, but the hammer should not fall.
m. Release the trigger.
n. Squeeze the trigger to check the single action.
NOTE: The hammer should fall.

6. Perform performance Steps 4 and 5 within 45 seconds.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M9, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Maintain an M249 Machine Gun

Tasks:

1. Maintain an M249 Machine Gun.

2. Perform a function check on an M249 Machine Gun (In Sequence).

Test Conditions:

During daylight, given an M249 Machine Gun and scraper tool.

Test Standards:

1. Within three minutes, correctly clear (In Sequence) and disassemble the M249 Machine
Gun into its eight major groups (if no hand guard is present place into seven major groups)
and components.
2. Within three minutes, correctly assemble the M249 Machine Gun and perform a function
check (In Sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-COM-4025 Maintain an M249 Machine Gun, and 071-COM4026 Perform a Function Check on an M249 Machine Gun. Performance measures can be
found on https://atn.army.mil.

Equipment Required for Station:

An M249 Machine Gun for each Candidate, scraper tool for each Machine Gun, stopwatch,
and EIB Form M249.2.

Site Setup:

Place M249 Machine Guns on the ground with the bipod extended. Layout a ground cloth at
each weapon with a scraper tool on the ground cloth.

Page:

Instructions to Candidate:

Let me have your attention. At this point, you are required to clear (In Sequence),
disassemble, assemble and perform a function check (In Sequence) on the M249 Machine
Gun. The purpose of this is to determine your ability to perform operator maintenance on an
M249 Machine Gun. You will show the scorer that you can clear (In Sequence), disassemble,
assemble, and perform a function check (In Sequence) on the weapon. The weapon must pass a
function check.
You have three minutes to clear (In Sequence) and disassemble the M249 Machine Gun into
eight major groups (if no hand guard is present place into seven major groups) and
components. You may use only the equipment that you will find on the ground cloth beside
your weapon. Place the disassembled parts on the ground cloth as you remove them. Do you
understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for 3 minutes and then say Stop.
You now have three minutes to assemble the M249 Machine Gun and perform a function
check (In Sequence). You may use only the equipment found on the ground cloth beside your
weapon. Place the assembled weapon on the ground cloth after you complete the assembly and
function check. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for 3 minutes and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Maintain an M249 Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Maintain an M249 Machine Gun.

2. Perform a function check on an M249 Machine Gun (In Sequence).

Performance Measures:

Pass

Fail

1. Clear the M249 Machine Gun (In sequence).

a. Move the safety to the fire position.

b. Lock the bolt to the rear by pulling the cocking handle to the rear using your right hand, palm up.
c. Return the cocking handle forward to its locked position.
d. Place the M249 Machine Gun on safe.
e. Performs 5 Point Safety Check
(1) Remove magazine, if present, by pushing down on the magazine release tab and pulling the
magazine out.
(2) Raise the feed tray cover assembly by pushing in the latches and tilting upwards.
a. Check the feed pawl assembly under the feed cover.
b. Check the feed tray assembly
(3) Raise the feed tray assembly by tilting upwards.
a. Check the chamber.
b. Check the space between the face of the bolt and the chamber.
c. Insert two fingers in the magazine well and feel for brass or ammunition.
f. Lower the feed tray.
g. Close the feed tray cover assembly by lowering it until it locks closed.
h. Move the safety to the fire position.
i. Pull the cocking handle to the rear, squeeze the trigger, and manually ride the bolt forward, and ensure the
cocking handle clicks into the locked position.

2. Disassemble the M249 Machine Gun into its eight major groups (if no hand guard is present place
into seven major groups). (Do not Grade in squence)
a. Remove drive spring, return rod and transfer mechanism assembly.
b. Remove the operating rod, slide assembly, and bolt assembly.
c. Remove the heat shield.
d. Remove the barrel.
e. Remove the handguard. (if present)
f. Remove the buttstock and buffer assembly.
g. Remove the trigger mechanism.
h. Remove the gas cylinder.
i. Remove the bipod.
j. Place in 7 Major Groups. (No hand guards)

3. Perform performance measures 1 and 2 within 3 minutes.

4. Assemble the M249 Machine Gun (Do not Grade in squence)

a. Replace the bipod and gas cylinder.
b. Replace the handguard. (if present)
c. Replace the barrel.
d. Replace the trigger mechanism.
e Replace the buttstock and shoulder assembly.
f. Replace the operating rod, slide assembly, and bolt assembly.
g. Replace the spring, return rod, and transfer mechanism assembly.
h. Replace the buttstock and buffer assembly.
i. Replace the heat shield assembly.

USAIS Form EIB M249, May 2014

Previous Edition is Obsolete

Ver 1.0

Expert Infantryman Badge

Test Scorecard

Maintain an M249 Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

5. Perform a function check on an M249 Machine Gun. (In Sequence)

a. Charge the weapon.
(1) Grasp the cocking handle with the right hand with palm up.
(2) Pull the bolt to the rear.
(3) Lock bolt to the rear.
b. Continue to hold the cokcing handle to the rear.
c. Use your left hand and move the safety to the safe postion.
d. Push the cocking handle forward into the forwar lock position.
e. Pull the trigger. Note: The weapon should not fire.
f. Grasp the cokcing handle with the right hand with palm up, and pull and hold it to the rear.
g. Move the safety to the fire position.
h. Continure to hold the cocking handle to the rear.
i. Use your left hand to pull the trigger and ease the bolt forward to prevent it from slamming into the
chamber and damaging the face of the bolt.
6. Perform performance measures 4 and 5 within 3 minutes.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M249, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 1.0

Clear, Load, Reduce Stoppage, Unload and Clear an M249 Machine Gun
Tasks:

1. Clear an M249 Machine Gun (In Sequence).

2. Load an M249 Machine Gun (In Sequence).
3. Correct malfunctions on an M249 Machine Gun (In Sequence).
4. Unload and clear an M249 Machine Gun (In Sequence).

Test Conditions:

During daylight, given an M249 Machine Gun scraper tool, and blank ammunition with at
least three good blank rounds followed by one expended round and then three more rounds.

Test Standards:

Within 30 seconds, clear, load, correct a malfunction, unload and clear an M249 Machine
Gun (In Sequence). Perform performance measures in the prone firing position.

Soldiers Manuel Crosswalk:

This task is based on task 071-COM-4027 Load an M249 Machine Gun, 071-COM-4029
Correct malfunctions of an M249 Machine Gun, and 071-COM-4028 Unload an M249 Machine Gun. Performance measures can be found on https://atn.army.mil.

Equipment Required for Station:

An M249 Machine Gun for each Candidate, scraper tool for each Machine Gun, blank
rounds, stopwatch, and EIB Form M249.2.

Site Setup:

Place the M249 Machine Gun on the ground with the bipod extended. Lay out a ground cloth
at each weapon. Set up blank ammunition with at least two good blank rounds followed by
one expended round and then two more rounds. This setup creates the malfunction necessary
to accomplish task M-2. Set up points M-1 and M-2 at a single site or at two separate sites.

Page:

Instructions to Candidate:

Let me have your attention, at this point you must clear, load an M249 Machine Gun,
perform immediate action on an M249 Machine Gun, unload and clear an M249
Machine Gun (In Sequence). The purpose of this test is to determine your ability to clear, load,
correct a malfunction, and unload and clear the M249 Machine Gun (In Sequence).
This point consists of the four tasks. You must pass all four of them to receive a GO. In order
to pass a task, you must correctly perform all of the performance measures for that task. If
you fail any task at this point, you will retest all of the four tasks.
You will have 30 seconds to clear, load an M249 Machine Gun, perform immediate action on
an M249 Machine Gun, and unload an M249 Machine Gun (In Sequence). When I say
Begin, you will immediately begin by clearing, loading and firing the weapon in the
direction it is now pointed. The belt of ammunition you have by your weapon will produce a
malfunction after you fire a few rounds. You must correct the malfunction and continue to fire
the weapon. You will then unload and clear the weapon (In Sequence).
You must accomplish all performance measures from the prone firing position. You may use
only the equipment you will find on the ground cloth beside your weapon. After you clear the
weapon, place it on the ground cloth.
Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidate to proceed for 30 seconds and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Clear, Load, Reduce stoppage, Unload and Clear an M249 Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Clear an M249 Machine Gun (In Sequence).

2. Load an M249 Machine Gun (In Sequence).
3. Correct malfunctions on an M249 Machine Gun (In Sequence).
4. Unload and clear an M249 Machine Gun (In Sequence).
Performance Measures:

Pass

Fail

1. Correctly clear the M249 Machine Gun (In Sequence).

a. Move the safety to the fire position.

b. Lock the bolt to the rear by pulling the cocking handle to the rear using your right hand, palm
up.
c. Return the cocking handle forward to its locked position.
d. Place the M249 Machine Gun on safe.
e. Performs 5 Point Safety Check.
(1) Remove magazine, if present, by pushing down on the magazine release tab and pulling the
magazine out.
(2) Raise the feed tray cover assembly by pushing in the latches and tilting upwards.
a. Check the feed pawl assembly under the feed cover.
b. Check the feed tray assemble.
(3) Raise the feed tray assembly by tilting upwards.
a. Check the chamber.
b. Check the space between the face of the bolt and the chamber.
c. Insert two fingers in the magazine well and feel for brass or ammunition.
f. Lower the feed tray
g. Close the feed tray cover assembly by lowering it until it locks closed.
h. Move the safety to the fire position.
i. Pull the cocking handle to the rear, squeeze the trigger, and manually ride the bolt forward
ensure the cocking handle clicks into the locked position.

2. Load the M249 Machine Gun (In Sequence).

(1) Load linked ammunition. Cant the M249 Machine Gun to the right.
(2) Open the feed tray cover assembly, if not open.
(3) Place the first round of the belt, with the open side of the links facing downward, in
the feed tray groove against the cartridge stop.
(4) Hold the ammunition belt in place on the feed tray with your left hand and then close
the feed tray cover assembly with your right hand.
(5) Squeeze the trigger
3. Take immediate action to correct a failure to fire (In Sequence).
a. Pull the cocking handle (right hand / palm up) to the rear.
b. Observe the ejection port to see if a cartage case, belt link, or round ejects.
(1) If nothing ejects.
a. Lock the bolt to the rear.
b. Proceed to remedial action.
(2) If a cartridge, belt link, or round ejects
USAIS Form EIB M249, May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Clear, Load, Reduce Stoppage, Unload and Clear an M249 Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

a. Correct an obstructed chamber.

(1) Ensure your face is not directly over the feed tray cover.
(2) Open the feed tray cover.
(3) Remove the ammunition, belt or magazine, all spent brass, links or loose rounds.
(4) Raise the feed tray assembly.
(5) Remove all spent brass, links, or loose rounds.
(6) Visually inspect the chamber for obstructions.
(7) Remove obstructions.
(8) Reload the M249 Machine Gun.
c. Push the cocking handle forward.
d. Squeeze the trigger.
4. Unload and Clear the M249 Machine Gun (In Sequence).
a. Move the safety to the fire position.
b. Lock the bolt to the rear by pulling the cocking handle to the rear using your right hand, palm
up.
c. Return the cocking handle forward to its locked position.
d. Place the M249 Machine Gun on safe.
e. Performs 5 Point Safety Check.
(1) Remove magazine, if present, by pushing down on the magazine release tab and pulling the
magazine out.
(2) Raise the feed tray cover assembly by pushing in the latches and tilting upwards.
a. Check the feed pawl assembly under the feed cover.
b. Check the feed tray assemble.
(3) Raise the feed tray assembly by tilting upwards.
a. Check the chamber.
b. Check the space between the face of the bolt and the chamber.
c. Insert two fingers in the magazine well and feel for brass or ammunition.
f. Lower the feed tray.
g. Close the feed tray cover assembly by lowering it until it locks closed.
h. Move the safety to the fire position.
i. Pull the cocking handle to the rear, squeeze the trigger, and manually ride the bolt forward.
Ensure the cocking handle clicks into the locked position.

Pass

Fail

5. Perform performance measures 1 through 4 from the prone firing position.

6. Perform performance measures 1 through 4 within 30 seconds.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M249, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Maintain an M240B Machine Gun

Tasks:

1. Maintain an M240B Machine Gun.

2. Perform a function check on an M240B Machine Gun (In Sequence).

Test Conditions:

During daylight, given an M240B Machine Gun.

Test Standards:

1. Within 3 minutes correctly clear (In Sequence) and disassemble the M240B Machine Gun
into eight major groups.
2. Within 3 minutes correctly assemble the M240B Machine Gun and perform a
function check (In Sequence).

Soldiers Manuel Crosswalk:

This task is based on task 171-025-0001 Maintain an M240B Machine Gun, and 071-0250002 Perform a Functions Check on an M240B Machine Gun. Performance measures can
be found on https://atn.army.mil. Do not perform any maintenance on the Machine Gun or
ammunition during the EIB test.

Equipment Required for Station:

M240B Machine Gun, ground cloth, dummy cartridge or nail, stopwatch, clipboard, field
table, and EIB Form M240B.1.

Site Setup:

Place a bipod-mounted M240B Machine Gun beside the canvas or tarpaulin. Place a dummy
cartridge or nail on the canvas or tarpaulin so that it is in plain view of the Candidate. Clear
the gun and place the weapon on SAFE.

Page:

Instructions to Candidate:

Let me have your attention. At this point, you are required to clear (In Sequence),
disassemble, assemble and perform a function check (In Sequence) on the M240B Machine
Gun. The purpose of this is to determine your ability to perform operator maintenance on an
M240B Machine Gun. You will show the scorer that you can clear (In Sequence), disassemble,
assemble, and perform a function check (In Sequence) on the weapon. The weapon must pass a
function check.
You have 3 minutes to clear (In Sequence) and disassemble the M240B Machine Gun into
eight major groups and components. You may use only the equipment that you will find on
the ground cloth beside your weapon. Place the disassembled parts on the ground cloth as you
remove them. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for 3 minutes and then say Stop.
You now have 3 minutes to assemble the M240B Machine Gun and perform a function
check (In Sequence). You may use only the equipment found on the ground cloth beside your
weapon. Place the assembled weapon on the ground cloth after you complete the assembly and
function check. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for 3 minutes and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Maintain an M240B Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Maintain an M240B Machine Gun.

2. Perform a function check on an M240B Machine Gun (In Sequence).

Performance Measures:

Pass

Fail

1. Clear the M240B Machine Gun (In Sequence).

a. Move the safety switch to the F (fire) position.
b. Charge the Machine Gun.
c. Move the safety switch to the S position.
d. Open the cover.
e. Remove the ammunition.
f. Raise the feed tray.
g. Look into the chamber for ammunition.
h. Lower the feed tray.
i. Move the safety switch to the F position.
j. Ease the recoiling parts forward.
k. Close the cover.
2. Disassemble the M240B Machine Gun into the eight major groups within 3
minutes. (Do not grade in sequence).
a. Remove the barrel assembly.
b. Remove the trigger housing assembly.
c. Remove the buffer assembly.
WARNING: Do not stand behind the weapon while removing the buffer, as the
driving spring may be released striking you or others.
d. Remove the driving spring assembly.
e. Remove the bolt and the operating rod assembly.
f. Remove the cover assembly.
1. Butt stock and buffer assembly
2. Bolt and operating rod assembly
3. Drive spring rod assembly
4. Trigger housing assembly
5. Barrel assembly
6. Cover assembly
7. Feed tray
8. Receiver
3. Perform performance measures 1 and 2 within 3 minutes.
USAIS Form EIB M240B, May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Maintain an M240B Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:
4. Assemble the M240B Machine Gun (Do not grade in sequence).
a. Install the feed tray.
b. Install the cover assembly.
c. Insert the cover spring pin.
d. Open the cover assembly.
e. Install the bolt and operating rod.
f. Close the cover assembly.
g. Install the driving spring assembly.
h. Install the buffer assembly.
j. Install the trigger housing.
l. Insert the trigger spring pin.
n. Install the barrel.
5. Perform a function check on an M240B Machine Gun (In Sequence).
a. Place the safety lever to the F position.
b. Lock the bolt to the rear position by pulling the cocking handle to the rear.
c. Push cocking handle to the forward postion until it locks in the forward
positon.
d. Place safety lever to the S postion.
e. Depress the trigger. Note: The bolt should not fall.
f. Place safety lever to the F position.
g. Pull and hold the cocking handle to the rear.
h. While holding the cocking handle to the rear, depress the trigger, and ease
the bolt forward and locked position.
i. Close the ejection port cover.
6. Perform performance measures 4 and 5 within 3 minutes.

USAIS Form EIB M240B, May 2014

Fail

Passed Failed

Reason (s) for Failure:

Scorers Signature:

Pass

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Clear, Load, Reduce Stoppage, Unload and Clear an M240B Machine Gun
Tasks:

1.
2.
3.
4.

Clear an M240B Machine Gun (In sequence).

Load an M240B Machine Gun (In sequence).
Correct malfunctions on an M240B Machine Gun (In sequence).
Unload and clear an M240B Machine Gun (In sequence).

Test Conditions:

During daylight, given an M240B Machine Gun, a five-round belt of linked 7.62-mm blank
ammunition with a dummy round inserted into the belt, and a requirement to expend all rounds in the
belt.

Test Standards:

1. Within 30 seconds, clear, load, correct a malfunction, unload and clear an M240B Machine
Gun (In Sequence). Perform performance measures in the prone firing position.

Soldiers Manuel Crosswalk:

This task is based 071-025-0003 Load an M240B Machine Gun, 071-025-0005 Correct
Malfunctions of an M240B Machine Gun, 071-025-0004 Unload an M240 Machine Gun.
Performance measures can be found on https://atn.army.mil.

Equipment Required for Station:

An M240B Machine Gun, a five-round belt of linked 7.62-mm blank ammunition with a
dummy round inserted into middle of belt (two rounds on either side), stopwatch, clipboard,
pencil, field table, and EIB Form M240B.2.

Site Setup:

Place a bipod-mounted M240B Machine Gun on a ground cloth. Place a dummy cartridge or
nail on the canvas or tarpaulin so that it is in plain view of the Candidate. Clear the gun and
place the weapon on SAFE.

Page:

Instructions to Candidate:

Let me have your attention. At this point you must clear, load an M240B Machine Gun,
perform immediate action on an M240B Machine Gun, unload and clear an M240B Machine
Gun (In sequence). The purpose of this test is to determine your ability to clear, load, correct
a malfunction, and unload and clear the M240B Machine Gun (In sequence).
This point consists of the four tasks. You must pass all four of them to receive a GO. In order
to pass a task, you must correctly perform all of the performance measures for that task. If
you fail any task at this point, you will retest all of the four tasks.
You will have 30 seconds to clear, load, fire, correct a malfunction, unload, and clear the
M240B Machine Gun (In sequence). When I say Begin, you will immediately
begin by clearing, loading and firing the weapon in the direction it is now pointed. The belt of
ammunition you have by your weapon will produce a malfunction after you fire a few rounds.
You must correct the malfunction and continue to fire the weapon. You will then unload and
clear the weapon (In sequence).
You must accomplish all performance measures from the prone firing position. You may use
only the equipment you will find on the ground cloth beside your weapon. After you clear the
weapon, place it on the ground cloth.
Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidate to proceed for 30 seconds and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Clear, Load, Reduce stoppage, Unload and Clear an M240B Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Tasks: 1.
2.
3.
4.

Rank:

Unit:

Clear an M240B Machine Gun (In sequence).

Load an M240B Machine Gun (In sequence).
Correct malfunctions on an M240B Machine Gun (In sequence).
Unload an M240B Machine Gun (In sequence).

Performance Measures:

Pass

Fail

1. Clear the M240B Machine Gun (In sequence).

a. Place safety to the F position.
b. Charge the weapon.
(1) Pull the cocking handle to the rear using your right hand, palm up, locking
the bolt in the rear position.
(2) Push the cocking handle to the forward and locked position.
c. Place safety to the S position.
d. Open the cover assembly.
e. Remove any ammunition if it is present.
f. Raise the feed tray.
g. Inspect the chamber to ensure no ammunition is present.
h. Lower the feed tray.
i. Place safety to the F position.
j. Pull and hold cocking handle to the rear.
k. While holding the cocking handle to the rear, depress the trigger and ease the
bolt forward to the closed and locked position.
2. Load the M240B Machine Gun (In sequence).
a. Position the open side of links in the down position.
b. Place link belt on feed tray with the first round against the cartridge
stop and tip of round pointing towards the barrel.
CAUTION: Make sure round does not move away from cartridge stop during
closing and latching of cover.
c. Close the cover assembly.
d. Ensure the latches lock into place.
e. Make sure round does not move away from cartridge stop during closing and
latching of cover.
3. Take immediate action to correct a failure to fire (In sequence).
a. Grasp the cocking handle (palm up) and pull it to the rear.
b. Look at the ejection port to see if a cartridge case, belt link, or round
is ejected.

(1) If nothing is ejected:

a. Lock the bolt to the rear.
b. Return the cocking handle forward.
c. Place the safety to S and take remedial action.

USAIS Form EIB M240B, May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Clear, Load, Reduce stoppage, Unload an M240B Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:
(2) If a cartridge or round is ejected:
a. Return the cocking handle to the forward position.
b. Aim and fire the weapon at the target.
4. Remove ammunition from the M240B Machine Gun (In sequence).
a. With palm up, pull the cocking handle to the rear, ensuring that the bolt
locks to the rear.
b. Return the cocking handle to its forward position.
c. Place the safety lever on S (safe).
d. Raise the cover and remove ammunition belt.
e. Remove any ammunition, links, or brass from the chamber area.
5. Clear the M240B Machine Gun (In sequence).
a. Confirm that no ammunition remains in the chamber.
b. Close the cover.
c. Place the safety on F (fire).
d. With palm up, pull the cocking handle to the rear and hold it.
CAUTION: The bolt must be eased forward to prevent damage to the feed tray
assembly and operating rod assembly.
e. Pull the trigger, allowing the bolt to ease forward.
f. Place the safety on F (fire).
6. Perform performance measures 1 through 5 from the prone firing position.
7. Perform performance measures 1through 5 within 30 seconds.

USAIS Form EIB M240B, May 2014

Fail

Passed Failed

Reason (s) for Failure:

Scorers Signature:

Pass

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Prepare Range Card for an M240B Machine Gun

Tasks:

1. Prepare Range Card for an M240B Machine Gun.

Test Conditions:

As a gunner, in a defensive fighting position with at least 500 meters open to the front, given a
tripod-mounted Machine Gun with a traversing and elevation (T&E) mechanism, an assigned
primary sector of fire with three recognizable targets and a givien FPL (final protective line),
a secondary sector of fire with two recognizable targets, blank DA Forms 5517-R, Standard
Range Card, a pencil, a lensatic compass, and a map of your assigned sector of fire.

Test Standards:

Complete the marginal information on the standard range card, sketch the primary sector of
fire to include the FPL, record the gun firing data, sketch the secondary sector of fire, label the
dead space, and record the position of the Machine Gun within 15 minutes.

Soldiers Manuel Crosswalk:

This task is based on task 071-000-0005 Prepare a Range Card for a Machine Gun.
Performance measures can be found on https://atn.army.mil.

Equipment Required for Station:

Provide the Soldier with the equipment and or materials described in the conditions statement.

Site Setup:

Place a tripod mounted M240B Machine Gun in a fighting position. Put a lensatic compass,
blank DA Form 5517-R, and a pencil beside the range card. Mark the limits of the primary
and secondary sectors of fire ahead of time so the Candidate can readily identify them. (use
natural features or man-made objects)

Page: 80

Instructions to Candidate:

Let me have your attention. At this point you will have 15 minutes to prepare a range card for
the M240B Machine Gun. You have an M240B Machine Gun mounted on a tripod, a map of
this area, a lensatic compass, a standard blank range card, and a pencil.
You are currently located at grid ___________ (give Candidate an eight digit grid to include
grid zone identifier), your primary sector of fire is from
(point out left or right
limit) to
(point out the other limit). Your secondary sector of fire is from
__
(point out left or right limit) to
(point out the other
limit). Your final protective line is
(point out the FPL). You are only required
to make one copy of your range card for this test. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have said.
Pause five seconds and then say Begin.
Allow the Candidate to proceed for 15 minutes and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard
Prepare Range Card for an M240B Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: Prepare Range Card for an M240B Machine Gun.

Performance Measures:

Pass

Fail

1. Complete the marginal information located at the top and center of the standard range
card.
a. Record the squad, platoon, and company designations.
b. Record the relative direction of magnetic north.
c. Record your defensive position as primary.
d. Record the date and time the range card was prepared.
e. Record the type of Machine Gun used (M240B).
f. Record the incremental distance of the nine range circles.

2. Sketch the primary sector of fire using a FPL.

a. Draw a basic Machine Gun symbol (an arrow) as a long line down the
appropriate left or right limit.
b. Draw another long arrow for the opposite limit (left or right).
c. Sketch the grazing fire and dead space along the FPL.
3. Develop the sketch for the primary sector of fire.
a. Identify all prominent terrain features within the primary sector of fire.
b. Sketch an appropriate symbol for each target at the targets approximate position
within the primary sector of fire.
c. Number all targets consecutively, beginning with the number 2, in order
of tactical importance and circle the target number. (The FPL is numbered as target 1.)

4. Record the gun firing data in appropriate space of the data section.

a. Record the target numbers, in numerical order.

b. Record DIRECTION/DEFLECTION data in the appropriate block.
(+/- 3 or +/- 54 Mils)
c. Record ELEVATION data in the appropriate block.
d. Record the RANGE data, in meters, in the appropriate block. (+/-20%)
e. Record any special ammunition required in the AMMO block.
f. Describe the target in the block labeled DESCRIPTION.
g. Record REMARKS in the appropriate block.

USAIS Form EIB M240B Range Card, May 2014

Previous Edition is Obsolete

Ver 1.0

Expert Infantryman Badge

Test Scorecard

Prepare Range Card for an M240B Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

5. Sketch the secondary sector of fire.

a. Draw a V using two broken lines to represent the left and right limits of the
secondary sector of fire.
b. Sketch identified targets in the secondary sector of fire.
c. Record the range (in meters) to each target above the targets sketch.
d. Employ field expedient firing stakes for the secondary sector.

6. Label the area between the primary and secondary sectors as dead space.
7. Record the position of the Machine Gun. (use the grid method)
a. Determine the eight digit grid coordinate of the gun.
b. Record the coordinate directly below the gun position.

8. Perform performance measures 1 through 7 within 15 minutes.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M240B Range Card, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 1.0

Clear, Load, Unload and Clear an M203 Grenade Launcher

Tasks:

1. Clear an M203 Grenade Launcher. (In sequence)

2. Load an M203 Grenade Launcher (In sequence).
3. Unload and Clear an M203 Grenade Launcher (In sequence).

Test Conditions:

During daylight, given a M203 Grenade Launcher, ammunition, and a requirement to load
and unload the weapon.

Test Standards:

1. Within 10 seconds, correctly clear and load the M203 Grenade Launcher (In sequence).
2. Within 10 seconds, correctly unload the M203 Grenade Launcher (In sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-COM-2127 Load an M203 Grenade Launcher, and
071-COM-2128 Unload an M203 Grenade Launcher. Performance measures can be found on
https://atn.army.mil.

Equipment Required for Station:

Field table, M203 Grenade Launcher with ammunition, and EIB Form M203.2.

Site Setup:

At the test site, in an outside field environment, provide all equipment and materials listed in
the task conditions statement.

Page:

Instructions to Candidate:

Let me have your attention. At this point, you must clear, load, and unload the M203
Grenade Launcher (In sequence). The purpose of this is to determine your ability to correctly
load and unload the M203 Grenade Launcher (In sequence). You will show the scorer that
you can load and unload the M203 Grenade Launcher (In sequence).
You have 10 seconds to load the M203 Grenade Launcher (In sequence). You may use only
the ammunition that you will find beside the weapon located on the field table.
Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for 10 seconds, and then say Stop
You now have 10 seconds to unload and clear the M203 Grenade Launcher (In sequence).
After you have unloaded and cleared the M203 Grenade Launcher (In sequence), place the
weapon on the field table. Do you understand what you must do?
Pause five seconds and then say Begin.

Page:

Expert Infantryman Badge

Test Scorecard

Clear, Load, Unload and Clear an M203 Grenade Launcher

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Clear the M203 Grenade Launcher (In sequence).

2. Load the M203 Grenade Launcher (In sequence).
3. Unload and Clear the M203 Grenade Launcher (In sequence).

Performance Measures:

Pass

Fail

1. Ensure the safety is in SAFE (S) position until ready to fire.

2. Depress barrel latch.
3. Slide barrel assembly forward.
4. Make sure the bore and chamber are clean and dry before loading.
5. Insert the ammunition into the chamber.
6. Slide the barrel closed until it locks and clicks.
7. Perform tasks 1 through 6 within 10 seconds (In sequence).
8. Point the weapon muzzle in a safe direction.
9. Attempt to place the safety in the S position.
10. Remove the live round or spent cartridge case from the M203.
NOTE: If you are not positive that the round is a spent cartridge then use the
procedures for removing a live round.
a. Remove a live round.
(1) Depress the barrel latch.
(2) Place one hand under the barrel assembly forward of the trigger guard.
(3) Slowly slide barrel assembly forward.
(4) Grasp the round with one hand as it ejects.
(5) Secure the round as per unit standing operating procedure (SOP).
11. Close the barrel by sliding it until it locks, unless preparing to load the M203.
12. Secure the round.
13. Perform tasks 8 through 12 within 10 seconds (In sequence).

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M203, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Clear, Load, Unload an M320 Grenade Launcher

Tasks:

1. Clear an M320 Grenade Launcher (In sequence).

2. Load an M320 Grenade Launcher (In sequence).
3. Unload and Clear an M320 Grenade Launcher (In sequence).

Test Conditions:

During daylight, given a M320 Grenade Launcher, ammunition, and a requirement to load
and unload the weapon.

Test Standards:

1. Within 10 seconds, correctly clear and load the M320 Grenade Launcher (In sequence).
2. Within 10 seconds, correctly unload and clear the M320 Grenade Launcher (In sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-031-0002 Load an M320 Grenade Launcher, and
071-031-0003 Unload an M320 Grenade Launcher. Performance measures can be found on
https://atn.army.mil.

Equipment Required for Station:

Field table, M320 Grenade Launcher with ammunition, and EIB Form M320.2.

Site Setup:

At the test site, in an outside field environment, provide all equipment and materials listed in
the task conditions statement.

Page:

Instructions to Candidate:

Let me have your attention. At this point, you must clear, load, and unload the M320
Grenade Launcher (In sequence). The purpose of this is to determine your ability to correctly
load and unload the M320 Grenade Launcher (In sequence). You will show the scorer that
you can load and unload the M320 Grenade Launcher (In sequence).
You have 10 seconds to load the M320 Grenade Launcher (In sequence). You may use only
the ammunition that you will find beside the weapon located on the field table.
Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for 10 seconds, and then say Stop.
You now have 10 seconds to unload the M320 Grenade Launcher (In sequence). After you
have unloaded the M320 Grenade Launcher (In sequence), place the weapon on the field
table. Do you understand what you must do?
Pause five seconds and then say Begin.

Page:

Expert Infantryman Badge

Test Scorecard

Clear, Load, Unload and Clear an M320 Grenade Launcher

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Clear an M320 Grenade Launcher (In sequence).

2. Load an M320 Grenade Launcher (In sequence).
3. Unload an M320 Grenade Launcher (In sequence).

Performance Measures:

Pass

Fail

1. Point muzzle of weapon in a safe direction.

2. Ensure selector lever is in S (safe) position.
3. Remove the muzzle cap.
4. Press barrel release and pivot barrel out from receiver.
5. Insert cartridge into barrel.
6. Ensure cartridge is seated fully forward in rear of barrel.
7. Pivot barrel into receiver until barrel locking lever engages barrel.
8. Perform performance measures 1 through 7 within 10 seconds (In sequence).
9. Point muzzle of weapon in a safe direction, with trigger finger outside trigger
guard.
10. Place selector lever in S (safe) position.
11. Press upward on barrel release lever.
12. Inspect barrel for presence of ammunition.
13. Remove any round or cartridge case by hand.
14. Pivot barrel into receiver until barrel release lever engages barrel.
15. Ensure selector lever remains in S (safe) position.
16. Perform performance measures 9 through 15 within 10 seconds
(In sequence).

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS EIB Form M320, March 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Clear, Load, Correct a Malfunction, and Unload and Clear an Caliber .50 Machine Gun

Tasks:

1. Clear a Caliber .50 Machine Gun (In sequence).

2. Load a Caliber .50 Machine Gun (In sequence).
3. Correct Malfunctions on a Caliber .50 Machine Gun (In sequence).
4. Unload and Clear a Caliber .50 Machine Gun (In sequence).

Test Conditions:

During daylight, given an assembled and cleared caliber .50 Machine Gun with headspace
and timing correctly set; a belt of linked caliber .50 blank ammunition with a dummy round
inserted into the belt; and a requirement to expend all rounds in the belt.

Test Standards:

1. Within 30 seconds, clear, load, correct a malfunction, unload and clear an Caliber .50
Machine Gun (In sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-022-0003 Load a Caliber .50 M2 Machine Gun, 071-022-0005
Correct Malfunction of a Caliber .50 M2 Machine Gun, and 071-022-0004 Unload a Caliber
.50 M2 Machine Gun. Performance measures can be found on https://atn.army.mil.

Equipment Required for Station:

An assembled Caliber .50 Machine Gun (tripod-mounted), with headspace and timing set; a
five-round belt of blank Caliber .50 Machine Gun ammunition with a dummy round inserted
in the middle position of the belt (two blank rounds on either side), a pencil, ballpoint pen,
field table, stopwatch, clipboard, earplugs, and EIB Form .50Cal.2.

Site Setup:

Ensure the site provides for the safe firing of Caliber .50 Machine Gun blank ammunition and
does not unduly interfere with other test stations. The selected site should be relatively level,
and the tripod-mounted gun should be well emplaced to prevent movement during the test.

Page: 90

Instructions to Candidate:

Let me have your attention. At this point, you must clear, load a Caliber .50 Machine
Gun, apply immediate action on a Caliber .50 Machine Gun, and unload and clear a Caliber
.50 Machine Gun (In sequence). You will load and fire the Caliber .50 Machine Gun on
automatic within 30 seconds.
When a stoppage occurs, you must apply immediate action and continue with the test.
You must unload and clear the Caliber .50 Machine Gun (In sequence).
You will receive an assembled Caliber .50 Machine Gun with headspace and timing correctly
set, a belt of linked, Caliber .50 Machine Gun ammunition, and a requirement to expend all
rounds in the belt. Do you understand what you must do?
If anyone has questions, repeat the instructions, but do not elaborate on what you have read.
Wait five seconds and say BEGIN.
Allow the Candidate to continue for the full 30 seconds. Allow the Candidate to proceed from
one phase of this test to the next phase without stopping after each requirement. Then say
STOP.

Page:

Expert Infantryman Badge

Test Scorecard
Clear, Load, Correct a Malfunction, Unload and Clear an Caliber .50 M2 Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Clear an Caliber .50 Machine Gun (In sequence).

2. Load an Caliber .50 Machine Gun (In sequence).
3. Correct Malfunctions on an Caliber .50 Machine Gun (In sequence).
4. Unload and Clear an Caliber .50 Machine Gun (In sequence).
Performance Measures:
1. Clear the .Caliber .50 Machine Gun (In sequence).

Pass

Fail

a. Place trigger block on S (safe).

b. Unlock the bolt latch release.
c. Raise the cover.
d. Lift the cartridge extractor and remove any ammunition if present from the feedway.
e. Place cartridge extractor down and close the cover.
f. Pull and lock the bolt to the rear, leaving the rectracting slide handle to the rear and
open the cover.
g. Visually inspect the chamber and T-slot.
h. Press the bolt lactch release and ease the bolt forward with the rectracting slide
handle.
i. Close the cover.
j. Press the trigger.
2. Load ammunition (In sequence) NOTE: There are two ways to load ammunition,
with the machine gun cover open and with the machine gun cover closed.
a. Loading with machine cover open.
b. Ensure the bolt latch release is locked.
c. Open the cover.
d. Insert the double-loop end of the belt in the feed tray until the belt-holding pawl
engages the first round.
e. Close the cover.
f. Pull the retracting slide handle rearward, retracting the bolt all the way to the rear.
g Release handle.
h. Pull the retracting slide handle rearward for a second time to fully load the gun.
i. Release handle NOTE: A round is now in the chamber and the machine gun is ready
to fire.
a. Loading with the machine cover closed.
b. Ensure the bolt is forward
c. Insert the double loop end of the ammunition belt into the feedway until the first
round is engaged by the belt-holding pawl.
d. Pull the retracting slide handle rearward, retracting the bolt all the way to the rear.
e. Release the handle
f. Realease handle
g. Pull the retracting slide handle rearward for a second time to fully load the gun.

USAIS Form EIB .50Cal., May 2014

Previous Edition is Obsolete

Ver 1.0

Expert Infantryman Badge

Test Scorecard
Clear, Load, Correct a Malfunction, Unload and Clear an Caliber .50 M2 Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

e. Release the handle. NOTE: A round is now in the chamber and the machine gun is
ready to fire.
3. Correct malfunction to return the weapon to service (In sequence).
a. Place the trigger block in the F (Fire) position.
b. Attempt to fire the weapon.
c. Pull the retracting slide handle rearward.
d. Observe if round or fired case is ejected, release retracting slide handle, and attempt
to fire again.

Pass

Fail

4. Unload and Clear the .50 Caliber M2 Machine Gun (In sequence).

a. Place trigger block on S (safe).

b. Unlock the bolt latch release.
c. Raise the cover.
d. Lift the cartridge extractor and remove the ammunition belt from the feedway.
e. Place cartridge extractor down and close the cover.
f. Pull and lock the bolt to the rear, leaving the rectracting slide handle to the rear and
open the cover.
g. Visually inspect the chamber and T-slot.
h. Press the bolt lactch release and ease the bolt forward with the rectracting slide
handle.
i. Close the cover.
j. Press the trigger.

5. Perform performance measure 1 through 4 within 30 seconds.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB .50Cal., May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 1.0

Set Headspace and Timing on a Caliber .50 Cal M2 Machine Gun

Tasks:

1. Set Headspace and timing on a Caliber .50 Machine Gun.

Test Conditions:

As a gunner, given a Caliber .50 Machine Gun (tripod mounted),and a headspace and timing
gage. You have been directed to set the headspace and timing of the weapon.

Test Standards:

Set headspace to ensure the GO end of the headspace gage will enter the T slot and the NO
GO end will not. Set the timing for the weapon to fire when recoiling pater are between .020
and .116 inch out of battery. Complete setting the headspace and timing within eight minutes.

Soldiers Manuel Crosswalk:

This task is based on task 071-313-3455 Set Headspace and Timing on a Caliber .50 M2
Machine Gun. Performance measures can be found on https://atn.army.mil.

Equipment Required for Station:

An assembled caliber .50 machine gun (tripod-mounted) with headspace and timing
gauge, stopwatch, clipboard, and EIB Form .50Cal.3.

Site Setup:

Ensure the Machine Gun is tripod-mounted and well emplaced to prevent movement during
the test.

Page:

Instructions to Candidate:

Let me have your attention. At this point you must set headspace and timing on a Caliber
.50 Machine Gun within eight minutes. You will receive the necessary tools and equipment.
You must perform this task without injuring yourself or damaging the equipment. Do you
understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidate to proceed for eight minutes and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Set Headspace and Timing on a Caliber .50 Cal M2 Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Set Headspace and Timing on a Caliber .50 Machine Gun.

Performance Measures:

Pass

Fail

1. Clear the weapon.

2. Adjust headspace.
a. Raise top cover all the way up.
b. Grasp retracting slide handle and retract bolt to align barrel locking spring lug with
the 3/8 inch hole in the right side of receiver while inserting barrel.
c. Holding bolt in the retracted position, screw the barrel fully into the barrel
extension.
d. With bolt still retracted, unscrew barrel two notches (clicks).
e. Release retracting slide handle and allow bolt to go forward.
f. Pull bolt to rear with retracting slide handle and hold (withdraws firing pin into
bolt). Otherwise headspace gage wont fit at all.
g. Single shot mode.
(1) Hold retracting slide handle.
(2) Push the bolt latch release.
(3) Slowly return bolt forward.
NOTE: Do not slam bolt forward.
h. Remove slack in the bolt and barrel extension by retracting the retracting slide
handle until the barrel extension begins to separate (but not more than 1/16 inch)
from the trunnion block.
i. While maintaining 1/16 inch separation, raise cartridge extractor and attempt to
insert the GO end of the GO/NO GO headspace gage in the T slot between the face
of the bolt and the rear of barrel all the way to the ring, then attempt to insert the NO
GO end of the GO/NO GO headspace gage.
(1) If GO end of headspace gage enters freely all the way to the ring and NO GO
end does not enter, headspace is correct. Proceed to Adjust Timing.
(2) If GO end of headspace gage does not enter T-slot freely, headspace is
too tight. Proceed to Step 2i(2)(a).
a. If GO end of headspace gage will not enter T-slot, retract bolt so you can
see barrel locking spring lug in center of 3/8 inch hole on right side of receiver.
b. Unscrew barrel one notch (click).
c. Repeat steps 2i(2)(a) and 2i(2)(b) above until NO GO end of headspace
gage does not enter and GO end of headspace gage enters, if necessary.
USAIS Form EIB .50Cal., May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Set Headspace and Timing on a Caliber .50 Cal M2 Machine Gun

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

3. Adjust Timing.
a. Ensure proper headspace before adjusting timing.
b. Pull bolt to rear with retracting slide handle to cock Machine Gun; while holding
handle, depress the bolt latch release and slowly return bolt forward. Do not press trigger.
c. Grasp retracting slide handle and retract bolt just enough to insert FIRE gage with
beveled edge against barrel notches between barrel extension and trunnion block. Release
retracting slide handle slowly.
d. Remove backplate assembly.
e. Screw timing adjustment nut clockwise all the way down (Nut should turn hard).
f. Remove FIRE gage.
(1) Reinstall backplate assembly.
(2) Reinsert FIRE gauge.
g. Remove backplate assembly.
h. Screw timing adjustment nut up counter clockwise one click.
i. Remove FIRE gage.
j. Reinstall backplate assembly, and reinsert FIRE gage.
k. Attempt to fire by depressing trigger. NOTE: Repeat, turning timing adjustment nut up
one click at a time, until gun fires.
l. Remove backplate assembly and turn timing adjustment nut two more clicks
up (to the right).
m. Remove FIRE gage.
n. Install backplate assembly.
4. Perform Function Check.
a. Pull retracting slide handle to rear to charge Machine Gun.
b. Depress bolt latch release and slowly ease bolt forward with retracting slide handle.
c. Grasp retracting slide handle and retract bolt just enough to insert NO FIRE gage with
beveled edge against barrel notches between barrel extension and trunnion block.
d. Release retracting slide handle slowly.
e. Depress trigger, gun should NOT fire.
NOTE:If Machine Gun does fire, it has early timing. Re-adjust timing.
f. Retract bolt just enough to remove NO FIRE gage and insert FIRE gage with beveled
edge against barrel notches between barrel extension and trunnion block.
g. Release retracting slide handle slowly.
h. Depress trigger; Machine Gun should fire. Timing is now complete.
i. Re-adjust timing or notify field maintenance, If Machine Gun does not fire.
j. Repeat steps 4a through 4h with both FIRE and NO FIRE gages two more times to
ensure that adjustment is correct.
5. Perform performance measures 1 through 4 within 8 minutes.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB .50Cal, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Prepare M136 for Firing / Perform Misfire Procedures

Tasks:

1. Prepare an M136 Launcher for Firing (In sequence).

2. Perform Misfire procedures on an M136 Launcher (In sequence).

Test Conditions:

Prepare the M136 Launcher, arm the weapon in the correct sequence prior to firing, apply
misfire procedures so that the M136 Launcher can be fired, or ensure the weapon cannot be
fired. (In sequence)

Test Standards:

1. Within 15 seconds, prepare the M136 Launcher for firing (In sequence) .
2. Within 45 seconds, apply immediate action after the grader announces, MISFIRE
(In sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-054-0001 Prepare an M136 Launcher for Fire, and 071-0540003 Perform Misfire Procedures on an M136 Launcher. Performance measures can be found
on https://atn.army.mil.

Equipment Required for Station:

An M136 Launcher, clipboard, pencil, stopwatch, field table, and EIB Form AT4.1.

Site Setup:

Provide a field table for the M136 Launcher.

Page: 98

Instructions to Candidate:

Let me have your attention. At this point you must prepare an M136 Launcher for firing,
attempt to fire and perform misfire procedures on an M136 launcher (AT4) (In sequence).
You will prepare the M136 Launcher for firing, attempt to fire, and apply immediate action to
correct a malfunction (In sequence). A prefire inspection has already been performed on the
M136 launcher. You have 15 seconds to prepare the M136 Launcher for firing and attempt to
fire (In sequence). At the end of the 15 seconds, I will announce, MISFIRE. You then have
45 seconds to perform immediate action for misfire (In sequence).
This is not a live-fire exercise. Your target is ___. You may fire from any position you
choose. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidate to proceed for 15 seconds. Once the Candidate assumes a proper firing
position and has attempted to fire (In sequence), say the following:
You have tried to fire the M136 Launcher, but it has misfired. Take appropriate
action now.
Allow the Candidate to proceed for 45 seconds and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard

Prepare M136 for Firing / Perform Misfire Procedures

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Prepare an M136 Launcher for Firing (In sequence).

2. Perform Misfire procedures on an M136 Launcher (In sequence).

Performance Measures:

Pass

Fail

1. Prepare the M136 Launcher for firing (In sequence)

a. Remove the M136 from its carrying position, and cradle in the left arm.
b. Keeping the munitions muzzle toward the target area.
c. Pull and release the transport safety pin using the right hand.
d. Unsnap, unfold and hold the shoulder stop with the right hand.
e. Grip the base of the sling on the front of the launcher with the left hand and the
shoulder stop with the right hand.
f. Raise the munition out away from the body.
g. While keeping the munition pointed at the target, pivot the body 90 degrees to face
the target.
h. Place the munition on the right shoulder.
i. Grasp the front sight cover with the right hand, pressing down, and sliding it
rearward.
j. Grasp the rear sight cover with the right hand, pressing downward and sliding it
forward.
k. Ensure the back-blast area is cleared of personnel.
l. Unfold the cocking lever with the right hand.
m. Place the thumb under the cocking lever.
(1) Push the cocking lever forward using the support of the fingers in front of the firing
mechanism.
(2) Rotate the cocking lever downward and to the right.
(3) Allow the cocking lever to slide backward.

n. Adjust the rear sight to the correct range.

o. Place the first two fingers of the right hand on the red safety catch and extend the
thumb.
p. Pull back on the sling with the left hand to seat the shoulder stop firmly against the
shoulder.
q. Attempt to fire the M136 Launcher.
2. Perform performance measure 1 within 15 seconds (In sequence).

USAIS Form EIB M136 May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Prepare M136 (AT4) for Firing / Perform Misfire Procedures

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

3. Perform misfire procedures on an M136 Launcher (In sequence).

NOTE: If not in a combat situation, shout Misfire and wait five seconds.
a. Announce Misfire just loudly enough for friendly personnel in the immediate area
to hear.
b. Maintain the original sight picture.
c. Keep the AT4 pointed at the target.
d. Keep the backblast area clear.
e. Release the red trigger button.
f. Release the red safety release catch.
g. If situation permits, wait five seconds.
h. Remove your right hand from the firing mechanism.
i. Check the back-blast area.
j. Re-cock the AT4.
k. Firmly press downward on the red safety release catch, and hold.
l. Aim the AT4.
m. Press and hold the red trigger button.
n. Announce Misfire just loudly enough for friendly personnel in the immediate area to
hear.
o. Keep the AT4 pointed at the target.
p. Release the red trigger button.
q. Release the red safety release catch.
r. If situation permits, wait two minutes.
s. Return the cocking lever to the SAFE (uncocked) position.
t. Remove the AT4 from your shoulder, keeping it pointed in safe direction.
u. Cradle the AT4 in your left arm.
v. Reinsert the transport safety pin / fork.
w. Break off the sights to identify the AT4 as misfired. (simulate)
x. Place the AT4 on the ground, pointed in safe direction.
4. Perform performance measure 3 within 45 seconds (In sequence).

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB M136 May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

Clear, Load, Correct a Malfunction, Unload and Clear an MK 19 40mm Grenade Machine Gun

Tasks:

1. Clear an MK 19 40mm Grenade Machine Gun (In sequence).

2. Load an MK 19 40mm Grenade Machine Gun (In sequence).
3. Correct malfunctions on an MK 19 40mm Grenade Machine Gun (In sequence).
4. Unload and clear an MK 19 40mm Grenade Machine Gun (In sequence).

Test Conditions:

As a gunner, given a MK 19 Grenade Machine Gun, mounted on a tripod, with linked 40mm grenade
ammunition, and a 40mm ammunition can. You have been directed to load the weapon and to take
immediate actions to correct a failure to fire, and to unload the weapon (In sequence).

Test Standards:

1. Within 1 minute, clear, load, correct a malfunction, unload and clear an MK 19 Grenade
Machine Gun (In sequence).

Soldiers Manuel Crosswalk:

This task is based on task 071-030-0005 Load an MK 19 Grenade Machine Gun, 071-0300008 Correct Malfunctions of an MK 19 Grenade Gun, and 071-030-0006 Unload an MK 19
Grenade Machine Gun. Performance measures can be found on https://atn.army.mil.

Equipment Required for Station:

An assembled MK 19 40mm Grenade Machine Gun (tripod-mounted with T&E mechanism),

a five-round belt of dummy MK 19 40mm Grenade Machine Gun ammunition, and a pencil
or pen, a field table, a stopwatch, a clipboard, earplugs, and EIB Form MK19.2.

Site Setup:

Ensure the site provides an MK 19 40mm Grenade Machine Gun with dummy ammunition.
The selected site should be relatively level, and the tripod-mounted gun should be well
emplaced to keep the weapon from moving during the test.

Page:

Instructions to Candidate:

Let me have your attention, at this point you must clear, load an MK 19 Grenade Machine Gun,
perform immediate action on an MK 19 Grenade Machine, and unload and clear an
MK 19 Grenade Machine (In Sequence). The purpose of this test is to determine your ability to
load, correct a malfunction, and unload and clear the MK 19 Grenade Machine
(In Sequence).
This point consists of the four tasks. You must pass all four of them to receive a GO. In order
to pass a task, you must correctly perform all of the performance measures for that task. If
you fail any task at this point, you will retest all of the four tasks.
You will have 1 minute to clear, load an MK 19 Grenade Machine, perform immediate action on an
MK 19 Grenade Machine, and unload and clear an MK 19 Grenade Machine
(In Sequence). When I say Begin, you will immediately begin by clearing, loading and firing the
weapon in the direction it is now pointed. The belt of ammunition you have by your
weapon will produce a malfunction after you fire a few rounds. You must correct the
malfunction and continue to fire the weapon. You will then unload and clear the weapon
(In Sequence).
You must accomplish all performance measures from the seated firing position. You may use only
the equipment you will find on the ground cloth beside your weapon.
Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidate to proceed for one minute and then say Stop.

Page:

Expert Infantryman Badge

Test Scorecard
Clear, Load, Correct a Malfunction, Unload and Clear an MK 19 40mm Grenade Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1. Clear an MK 19 40mm Grenade Machine Gun (In sequence).

2. Load an MK 19 40mm Grenade Machine Gun (In sequence).
3. Correct malfunctions on an MK 19 40mm Grenade Machine Gun (In sequence).
4. Unload and clear an MK 19 40mm Grenade Machine Gun (In sequence).
Performance Measures:

Pass

Fail

1. Clear the MK19 Machine Gun (In sequence).

a. Place the safety switch on S (safe).
b. Open the top cover assembly.
c. lower one or both charging handles.
d. Pull the charging handle slightly to the rear.
e. Allow sufficient space between the face of the bolt and the chamber to see both.
f. check for live ammunition.
g. Ride the bolt forward.
h. Return the charging handle to its orginal upright postion.
2. Attach feed throat to feeder
a. Squeeze the spring-loaded pins on feed throat.
b. Insert into the slots on both sides of the feeder.
3. Insert a round.
a. Open the top cover assembly.
b. Insert the round through the feed throat (female first) into the feeder.
c. Push the round across the first set of feeder pawls.
d. Ensure the round is straight and firmly seated against the bolt.
e. Push the secondary drive lever to the right.
f. Close the top cover assembly.
4. Load the first round to the fully-loaded position (In sequence).
a. Charge the weapon.
(1) Lower both charger handles.
(2) Pull both charger handles to the rear ensuring the bolt locks to the rear.
(3) Return both charger handles to the forward position.

b. Place safety switch in F (fire) position.

c. Squeeze the trigger allowing the bolt to slam forward.
d. Rotate both charger handles down.
e. Pull both charging handles to the rear.
f. Return both charging handle to the forward and up position.
g. Squeeze the trigger.

USAIS Form EIB MK19, May 2014

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard
Clear, Load, Correct a Malfunction, Unload and Clear an MK 19 40mm Grenade Machine Gun
For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

5. Take immediate action to correct a failure to fire.

a. Pull the charger handles to the rear.
b. Observe the ejection port to see if a case, link, or round ejects.
c. Push the charger handles forward to the up position.
d. Squeeze the trigger.
6. Unload and clear an MK 19 40mm Grenade Machine Gun (In sequence).
1. Place the safety switch to S (SAFE).
2. Remove the case catch bag, if applicable.

7. Charge the weapon.

8. Remove live round or spent case from the bolt, if present.
a. Insert the tip of a cleaning rod through the receiver rail as close to the bolt face as
possible.
b. Place the tip of the cleaning rod on top of the round or spent case, as close to the
bolt face as possible.
c. Position one hand beneath the weapon to catch the round as it falls out.
d. Force the live round off the bolt face and out the bottom of the gun by pushing
down on the cleaning rod.
e. Catch the live round as it falls out.
9. Open the top cover assembly.
10. Remove linked rounds from the feeder, if present.
a. Reach beneath the feed tray with one hand.
b. Press and hold both the primary and secondary positioning pawls.
c. Slide the linked rounds out of the feeder and out the feed throat.
d. Return the linked rounds to the ammunition can.
11. Return the bolt to the forward position.
a. Place the safety switch in the fire (F) position.
b. Hold one charger handle to the rear.
c. Ride the bolt forward by squeezing the trigger and easing the bolt forward.
d. Ensure both charging handles are forward and up position.
12. Place the safety switch in the S position.
13. Perform performance measures 1 through 12 within 1 minute in the seated position.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB MK19, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

12-Mile Foot March and Weapons Proficiency Test

Tasks:

1. 12-mile foot march.

2. Clear M16-Series Rifle / M4 Series Carbine (In sequence).
3. Maintain an M16-Series Rifle / M4 Series Carbine.
4. Perform a functions check on an M16-Series Rifle / M4 Series Carbine (In sequence).

Test Conditions:

During a prescribed time, given a predetermined 12-mile measured course with ACU uniform,
with appoved boots, and at a minimum: ACH, issued TA-50 load carrying equipment, (2)
1-quart, canteens, M16-Series Rifle / M4 Series Carbine, and a 35 pound ruck sack (dry
weight or without water). Units may add any aditional equipment to this per unit SOP or at
the direction of the EIB Board and Commander. The weapons proficiency test must be wihtin
50 meters of the finish point of the 12-mile foot march.

Test Standards:

1. Within 3 hours, complete the 12-Mile Foot March.

2. Within 2 minutes, Clear (In sequence) and Disassemble the M4 Series Carbine Rifle.
3. Within 2 minutes, Assemble the M4 Series Carbine Rifle and perform a functions check
(In sequence).

Soldiers Manuel Crosswalk:

This task is executed in acoordance with FM 21-18 Foot Marches 1 June 1990 and 071-1000029 Perform a Functions Check on an M16-Series Rifle / M4 Series Carbine, and 071-1000032 Maintain an M16 Series Rifle / M4 Series Rifle Carbine. Performance measures can be
found on https://atn.army.mil.

Equipment Required for Station:

Medical support, Finish Line clock with tripod, water points, mile markers, predetermined
road guards, trail fallout vehicle, and scales. Ground cloth at the weapons proficiency test
point, stop watch, clip board, pen, USAIS EIB Form M4.1

Site Setup:

Enusre there is a measured 12-Mile course for the foot march. The route of the foot march
must be clearly marked. The weapons proficiency test point should be within 50 meters of
the finish point. The weapons proficiency test point should have enough graders so that there
will be no prolonged wait for a Candidate to be tested. The weapons proficiency test must be
administered immediately when the Candidate crosses the finish line.

Page: 106

Instructions to Candidate:

Let me have your attention, at this point, you will be required to complete a 12-Mile Foot
March within three hours and complete the weapons proficiency test. All equipment will be
properly worn with the M16-Series Rifle / M4 Series Carbine, carried at the ready position.
Immediately crossing the finish line of the 12-Mile Foot March you will report to your grader
for your weapons proficiency test.
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed on the 12-Mile Foot March route. Immeditately after the
Candidate crosses the finish line the Candidate will report to a grader for the weapons
proficiency test.
Let me have your attention. At this point you must perform operator maintenance on an
M16-Series Rifle / M4 Series Carbine, and perform a function check on an M16-Series Rifle
/ M4 Series Carbine. The purpose of this is to determine your ability to perform operator
maintenance on an M16-Series Rifle / M4 Series Carbine. You will show the scorer that you
can clear, disassemble, assemble, and perform a function check in sequence on the weapon.
The weapon must pass a function check. You have two minutes to clear and disassemble the
M16-Series Rifle / M4 Series Carbine. You may use only the equipment that you will find on
the ground cloth beside your weapon. Place the disassembled parts on the ground cloth as you
remove them. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say Begin.
Allow the Candidates to proceed for two minutes and then say Stop.
You now have two minutes to assemble the M16-Series Rifle / M4 Series Carbine, and perform
a function check in sequence. You may use only the equipment found on the ground cloth
beside your weapon. Place the assembled weapon on the ground cloth after you complete the
assembly and function check. Do you understand what you must do?
If anyone has questions, repeat the instructions but do not elaborate on what you have read.
Pause five seconds and then say BEGIN.
Allow the Candidates to proceed for two minutes and then say STOP.

Page:

Expert Infantryman Badge

Test Scorecard

12-Mile Foot March and Weapons Proficiency Test

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Tasks: 1.
2.
3.
4.

12-mile foot march.

Clear M16-Series Rifle / M4 Series Carbine (In sequence).
Maintain an M16-Series Rifle / M4 Series Carbine.
Perform a functions check on an M16-Series Rifle / M4 Series Carbine (In sequence).
Pass
Fail
Performance Measures:

1. Completed the 12-Mile Foot March within three hours.

2. Weapons Proficiency Test.
a. Clear an M16-Series Rifle/ M4 Series Carbine (In sequence).

a. Point the weapon in a safe direction

b. Attempt to place the selector lever on Safe

c. Remove the magazine from the weapon, if present

d. Lock the bolt open (if not already open)
e. Ensure that no ammunition is in the receiver or chamber.
f. Press the upper portion of the bolt catch allowing the bolt to go forward.
g.Close the ejection port
b. Disassemble the weapon within 2 minutes.
(1) Remove the sling.
(2) Remove the hand guards only if you can see dirt or corrosion through the vent holes.
NOTE: Hand guards on the M16A2 are interchangeable because they are identical. On the M16A4
the hand guards can be replaced by the M5 adapter rails. On the M4 carbine series, the hand guards
can be replaced by the M4 adapter rails. The M4 and M5 adapter rails are marked with a T for top
and B for bottom. The operator is only authorized to remove the lower adapter rail and rail covers
for cleaning, lubrication, or attaching accessories.
(3) Push the take down pin as far as it will go.
(4) Pivot the upper receiver from the lower receiver.
(5) Push the receiver pivot pin in as far as it will go.
(6) Separate the upper and lower receivers.
(7) Remove carrying handle, if applicable.
(8) Pull back the charging handle.
(9) Remove the bolt carrier and bolt.
(10)Remove the charging handle.
(11)Disassemble the bolt carrier.
(12) Remove buffer and buffer spring from butt stock.
(13) Remove the butt stock. (M4 series only)

USAIS Form EIB Foot March 12.1, May 2014

Previous Edition is Obsolete

Ver 2.1

Expert Infantryman Badge

Test Scorecard

12-Mile Foot March and Weapons Proficiency Test

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.

Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

c. Perform performance measures A and B within 2 minutes.

d. Assemble the weapon.

Fail

(1) Insert the action spring and buffer.

(2) Assemble the bolt carrier.
(3) Engage and then push the charging handle in part of the way.
(4) Slide in the bolt carrier assembly.
(5) Push in the charging handle and the bolt carrier group together.
(6) Join the upper and lower receivers.
(7) Engage the receiver pivot pin.
(8) Close the upper and lower receiver groups.
(9) Push in the take down pin.
(10) Replace the hand guards.
(11) Replace the carrying handle, if applicable.
(12) Replace the sling.

e. Perform Functional Check (In sequence).

(1) Place selector lever on SAFE:

a. Pull charging handle to rear and release.
b. Pull trigger, hammer should not fall.
(2) Place selector lever on SEMI.
a. Pull trigger, hammer should fall.
b. Hold trigger to the rear and charge the weapon.
c. Release the trigger with a slow, smooth motion, until the trigger is fully forward.
d. Pull trigger. NOTE: The hammer should fall.
(3) Place the selector switch on BURST. (M16A2, M16A4, and M4 only)
a. Charge the weapon one time.
b. Squeeze and hold the trigger NOTE: The hammer should fall.
c. Charge weapon three times.
d. Release the trigger.
e. Squeeze the trigger NOTE: The hammer should fall.
(4) Place the selector switch on AUTO. (M16A1, and M4A1 only)
a. Pull the charging handle to the rear, charging the weapon.
b. Squeeze the trigger NOTE: The hammer should fall.
c. Hold the trigger to the rear.
d. Cock the weapon again.
e. Fully release the trigger then squeeze it again. NOTE: The hammer should not fall

because it should have fallen when the bolt was allowed to move forward during the chambering
and locking seqences.

f. Perform performance measures D and E within 2 minutes.

Passed Failed

Reason (s) for Failure:

Scorers Signature:
USAIS Form EIB Foot March 12.1, May 2014

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.1

APPENDIX C

Infantry Tasks

071-060-0004 Prepare a Javelin for Firing

071-060-0006 React to Javelin that Fails to Fire
071-060-0007 Restore a M98-series Javelin to Carrying Configuration
071-070-0002 Perform a Function Check on an M202A1 Multishot Rocket Launcher
071-070-0003 Load an M202A1 Multishot Rocket Launcher
071-070-0004 Unload an M202A1 Multishot Rocket Launcher
071-070-0005 Perform Misfire Procedures on an M202A1 Multishot Rocket Launcher
071-070-0006 Prepare an M202A1 Multishot Rocket Launcher for Firing
071-070-0007 Restore an M202A1 Multishot Rocket Launcher to Carrying Configuration
071-COM-4080 Send a Spot Report (SPOTREP)
071-COM-4407 Employ Hand Grenades
071-325-4426 Employ an M18A1 Claymore Mine
071-325-4426 Recover an M18A1 Claymore Mine
071-COM-0502 Move Under Direct Fire
071-COM-0510 React to Indirect Fire While Dismounted
071-326-0511 React to Flares
071-326-0512 Estimate Range
071-COM-0608 Use Visual Signaling Techniques
071-COM-1000 Identify Topographic Symbols on a Military Map
071-COM-1001 Identify Terrain Features on a Map
071-329-1014 Locate an Unknown Point on a Map and on the Ground by Intersection
071-329-1015 Locate an Unknown Point on a Map and on the Ground by Resection
071-329-7018 Prepare the AN/PSN-11 Precision Lightweight Global Positioning System
Receiver for Operation
071-329-7019 Enter Waypoints into an AN/PSN-11 Precision Lightweight Global
Positioning System Receiver
071-COM-0801 Challenge Persons Entering Your Area
071-440-0027 Execute Mechanical Breach in an Urban Operation
071-510-0001 Determine Grid Azimuth Using a Protractor
017-704-0001 Operate a Mini Eyesafe Laser Infrared Observation Set (MELIOS),
AN/PVS-6

Chemical, Biological, Radiological, and Nuclear Tasks

031-COM-1013 Decontaminate Yourself and Individual Equipment Using Chemical
Decontamination Kits
031-COM-1019 React to Chemical or Biological (CB) Hazard/Attack
031-COM-1021 Mark CBRN Contaminated Areas
031-COM-1035 Protect Yourself from Chemical and Biological (CB) Contamination Using
Your Assigned Protective Mask
031-COM-1036 Maintain Your Assigned Protective Mask
031-COM-1037 Detect Chemical Agents Using M8 or M9 Detector Paper
Page: 110

 031-COM-1040 Protect Yourself from CBRN Injury/Contamination with the JLIST

Chemical-Protective Ensemble
031-COM-1042 Protect Yourself from CBRN Injury/Contamination when Changing
MOPP using JLIST Chemical-Protective Ensemble
031-504-1004 Operate the Improved Chemical-Agent Monitor (ICAM)
031-506-1052 Protect Yourself and Others From Chemical and Biological Injury/
Contamination by Using a Collective Protection Shelter

Communications Tasks

113-305-1001 Communicate by Tactical Radio

113-571-1022 Perform Voice Communications
113-587-1005 Program Radio Set AN/PRC-148 (MBITR)
113-587-2002 Operate Multi-band Inter/Intra Team Radio (MBITR)
113-587-2071 Operate SINCGARS Frequency Hopping (FH) (Net Members)
113-587-2072 Operate SINCGARS Frequency Hopping (FH) Net Control Station (NCS)
113-589-2004 Operate TACSAT Radio Set AN/PRC-117 in all Modes of Operation
113-589-2007 Operate Force XXI Battle Command Brigade and Below (FBCB2)
113-609-2006 Operate Simple Key Loader (SKL) AN/PYQ-10
113-609-2053 Operate Automated Net Control Device (ANCD) AN/CYZ-10
441-066-1167 Operate the Defense Advanced Global Positioning System (GPS) Receiver
(DAGR)

Engineer Tasks

052-192-1270 React to a Possible Improvised Explosive Device (IED)

052-192-1271 Identify Visual Indicators of an Improvised Explosive Device
052-193-3261 React to an Improvised Explosive Device (IED) Attack
052-221-1010 Place Explosive Urban Breaching Charges

Field Artillery Tasks

061-283-6003 Adjust Indirect Fire

Medical Tasks
081-831-0044 Apply Pneumatic Splint to a Casualty with a Suspected Fracture of an
Extremity
081-COM-0101 Request Medical Evacuation
081-831-1001 Evaluate a Casualty (Tactical Combat Casualty Care)
081-COM-1003 Perform First Aid to Clear an Object Stuck in the Throat of a Conscious
Casualty
081-COM-1005 Perform First Aid to Prevent or Control Shock
081-COM-1007 Perform First Aid for Burns
Page: 111

081-COM-1023 Perform First Aid to Restore Breathing and/or Pulse

081-831-1025 Perform First Aid for an Open Abdominal Wound
081-831-1032 Perform First Aid for a Bleeding and/or Severed Extremity
081-831-1033 Perform First Aid for an Open Head Wound
081-831-1034 Perform First Aid for a Suspected Fracture
081-COM-1046 Transport a Casualty
081-833-0016 Insert an Oropharyngeal Airway (J Tube)
081-833-0075 Perform a Needle Chest Decompression
081-833-0161 Control Bleeding
081-833-0210 Apply a Tourniquet to Control Bleeding
081-833-0211 Apply a Hemostatic Dressing

Page: 112

APPENDIX D
Task: Adjust Indirect Fire
Condition: Given a pair of binoculars, radio, compass, pens/pencils, coordinate scale, map of the
target area, target to engage within the area and grid locations of friendly troops.
Standard: Determine the target location to within 250 meters of its actual location. The initial call
for fire is sent within 3 minutes after the target has been identified. Adjustments are sent within 45
seconds after each round impacts. Observer must enter the fire-for-effect phase using no more than
six rounds (initial round plus five for adjustment). Fire for effect must be within 50 meters of the
target using successive bracketing procedures (or creeping fire if danger close).
Performance Steps
1. Locate the target within 250 meters of the actual target location.
a. Locate the target by grid coordinates.
b. Determine the direction from your position to the target.
c. Formulate a Call for Fire. Include the elements of the call for fire in sequence.
(1) Observer identification (your call sign).
(2) Warning order (Adjust fire).
(3) Location of target (Grid data).
(4) Description of the target (for example INFANTRY PLATOON IN THE
OPEN.).
(5) Method of engagement (may be omitted if area fire is desired).
(a) If the target is within 600 meters of friendly troops, announce
DANGER CLOSE to the Fire Direction Center (FDC) in the initial call
for fire in the method of engagement phase.
(b) Use creeping procedures to adjust danger close fire, Range corrections
should not exceed 100 meters.
(c) Initial target location is reported on the enemy side of the target.
(6) Method of fire control.
Page: 113

2. Transmit the call for fire to the FDC within three minutes of target identification
a. Conduct three transmissions.
(1) Send observer identification and warning order. Example: A4Z57, THIS IS
G3H71, ADJUST FIRE, OVER
(2) Send target location. Example: GRID 180513, OVER. (Give the six-digit grid
of the target, with the grid zone identifier, to within 250 meters of the actual target
location.)
(3) Send target description, method of engagement, and method of fire and control.
Example: INFANTRY PLATOON IN THE OPEN, ICM IN EFFECT, OVER .
b. Give the direction to the target within 100 mils (M2 compass) or five degrees (lensatic
compass) or give an accurate cardinal direction (no compass available) of the targets actual
location. This should be sent before the first correction, or with the first correction.
3. Adjust rounds to within 50 meters of the target, within 45 seconds of the impact of each
adjusting round.
a. Spot each round when it impacts as right or left, over or short of your target.
b. Determine corrections for deviation left or right of the target
Note. Measure deviation. Measure the horizontal angle in mils, using the reticle pattern in
the binoculars or hand measurement of angular deviation. Estimate the range to the target
and divide by 1,000. This is the Observer-Target (OT) factor. IF the OT distance is 1,000
meters or greater, the OT Factor is expressed to the nearest whole number. If the OT distance
is less than 1,000 meters, the OT factor is expressed to the nearest 1/10th. For example,
800 = 0.8. Multiplying the OT factor by the deviation measured in mils produces deviation
corrections in meters.
c. When the first range spotting is observed, make a range correction that would result
in a range spotting in the opposite direction. For example, if the first round is short, add
enough to get an over on the next round. This is called successive bracketing. The target is
2100 meters away. Since the round is beyond the target, you must drop. You estimate that
the round is 250 meters beyond the target. Therefore, you must drop 400 meters to start
successive bracketing procedures. The round impacted 50 mils left of the target. With an
OT factor of 2, the round impacted 100 meters left. Your correction to the FDC is RIGHT
100-DROP 400-OVER.
WARNING DO NOT BRACKET when DANGER CLOSE, it
could result in friendly casualties, use the Creeping Fire Procedure (all
corrections are 100 meters or less).
d. Continue splitting the range bracket until a 100-meter bracket is split or range correct
Page: 114

spotting is observed, maintaining deviation on line.

e. Transmit corrections to the FDC in meters. The initial correction should bracket the
target in range. Deviation correction should be made to keep the rounds on the observer
target line.
f. Use the following guide to establish a bracket. When the estimated round impact distance
to the target is:
(1) More than 400 meters, add or drop 800 meters
(2) More than 200 but less than 400 meters, add or drop 400 meters
(3) More than 100 but less than 200 meters, add or drop 200 meters
(4) Less than 100 meters, add or drop 100 meters.
(5) Add or drop 50 meters and announce Fire for Effect.
4. Initiate Fire for Effect. When a 100-meter bracket is split or a range correct spotting is made, the
Fire for Effect phase is entered.
5. Observe the results of fire for effect, transmit refinements (if necessary), and provide end of
mission (EOM) and surveillance.
a. Determine the effects on the target.
b. Give a brief description of what happened to the target. Example: EOM, TARGET
DESTROYED, ESTIMATE TWO CASUALTIES, OVER.

Page: 115

Expert Infantryman Badge

Test Scorecard

Lane Alpha Scorecard

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Tasks: 113-609-2006

113-517-1022
071-COM-0502
081-831-1032
081-883-0210
081-883-0075
071-COM-4407
071-121-4080
061-283-6003
081-COM-0101

Performance Measures:

Rank:

Unit:

Operate Simple Key Loader

Perform Voice Communications
Move Under Direct Fire
Perform First Aid for Bleeding of an Extremity
Apply a Tourniquet to Control Bleeding
Needle Chest Decompression
Employ Hand Grenades
Send a Spot Report
Adjust Indirect Fire
Request Medical Evacuation

Pass

Fail

1. 113-609-2006 Operate Simple Key Loader

1. Press and hold the power button for 3 seconds.

2. With Stylus, enter the user name and password and tap
3. From the main page, Tap the launch button in the upper right corner, highlight UAS.
4. From the next page, Tap the equipment tab (EQS)
5. Highlight the loadset.
6. Tap the load icon in the upper right corner.
7. From the SINCGARDS mode page, select icon transfer, include time and tap ok.
8. Connect fill cable to audio/fill port on the radio and tap next.
9. Follow the instructions from the ECU wizard page and tap send.
10. Press load on the radio. After load is complete, set the function switch on the radio to the ON position.

2. 113-517-1022 Perform Voice Communications

1. Conduct radio check with higher headquarters using the proper abbreviated call sign.
2. Send tactical communications.
3. Receive tactical communication.
4. Sent message using the correct pro words and phonetic alphabet and numerals.

3. 071-COM-0502 Move Under Direct Fire

1. Select the best route to the next cover and concealed position.
2. Suppress the enemy as required.
3. Conduct movement using the appropriate technique.

a. Move using the high crawl technique

b. Move using the low crawl technique.

c. Move using the right technique ** Rushing more than 5 seconds **

4. 081-831-1032 Perform First Aid for Bleeding of an Extremity

1. Uncover the wound unless the clothing is stuck to the wound or you are in a chemical environment.
2. Check for entrance and exit wound.
3. Apply Chitosan dressing
Note: The chitosan dressing is used to control serious arterial bleeding. It is not used for wounds with minimal to
moderate bleeding. The chitosan dressing can be used in conjunction with a tourniquet to control severe arterial
bleeding.

a. Hold the foil over-pouch so that the instructions can be read and the unsealed edges are at the top.

b. Grasp the unsealed edges.

c. Peel open the over-pouch by pulling the unsealed edges apart.

d. Use your hand and thumb to trap the dressing between the bottom foil and the green/black polyester
backing.

e. Hold the dressing by the non-absorbent green/black backing and discard the foil over-pouch.

Lane Alpha Scorecard

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Lane Alpha Scorecard

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

Fail

Note: Do not let moisture from your hand come into contact with the dressing before you apply the bandage.
The moisture could cause the sponge to become sticky.
f. Apply the light-colored sponge portion directly over the wound and apply pressure to the green/black
backing with your fingers.
Note: Do not let the bandage come into contact with the casualtys eyes.
** g. Apply manual pressure and maintain the pressure until the dressing adheres and the bleeding stops

5. 081-883-0210 Apply a tourniquet to Control Bleeding

1. C-A-T. (NSN 6515-01-521-7976.)

a. Apply pressure to pressure point above the wound.

b. Take BSI.

c. Expose the wound enough to ensure the tourniquet is placed above the injury.

** d. Place C.A.T. between the heart and the wound on the injured extremity, 2-3 inches above the wound.

e. Pull the free end of the self adhering band through the buckle and route through the friction adapter

buckle (it is not necessary to route through friction adapter on an arm wound).

f. Pull the self adhering band tight around the extremity and fasten it back on itself.

** g. Twist the windlass until the bleeding stops.

h. Lock the windlass in place within the windlass clip.

i. Secure the windlass with the windlass strap.

j. Assess for the absence of a distal pulse (not indicated for amputations).

** k. Place a T and the time of application on the casualty.

l. Secure the C.A.T. in place with tape.

6. 081-883-0075 Needle Chest Decompression

** 1. Verify the presence of a tension pneumothorax.

** 2. Locate the insertion site. Locate the second intercostal space (between the second and third ribs) at the
midclavicular line (approximately in line with the nipple) on the affected side of the patients chest.
** 3. Thoroughly cleanse a 3 to 4 inch area around the insertion site. Begin in the center and work outward using a
circular motion.
** 4. Insert a 3 1/4 inch, 14 gauge needle over the top of the rib at a 90 degree angle to the chest wall, to the hub.
** 5. Remove the needle, leaving the catheter in place.
** 6. Stabilize the catheter hub to the chest with tape.
** 7. Place the casualty in a sitting position or in the recovery position with injured side down.
8. Record the treatment on the Field Medical Card.
9. Continue monitoring casualty by reassessment of reoccurrence of respiratory distress.

7. 071-COM-4407 Employ Hand Grenades

1. Position your body in a covered position.

2. Grip the hand grenade so you are holding the safety lever down with your thumb. Keep the pull ring safety clip free.
Position your body in a covered position facing the nonthrowing hand.
3. Remove the safety clip and safety pin while remaining behind cover.
4. Look at the target.
5. Throw the grenade overhand while keeping your eyes on the target.
6. Return to position behind cover until the hand grenade detonates.
** 7. Do not expose your body for more than five seconds at any one time.
Troops in open (35 meters away); one grenade must detonate within 5 meters of the center of target.

Lane Alpha Scorecard

Previous Edition is Obsolete

Ver 2.0

Expert Infantryman Badge

Test Scorecard

Lane Alpha Scorecard

For use of this for, See USAIS Pam 350-6. Proponent is USAIS.
Name: (Last, First, MI)

Rank:

Unit:

Performance Measures:

Pass

8. 071-121-4080 Send a Spot Report

Fail

1. Prepare SPOTREPORT
2. Sent SPOTREPORT to higher headquarters.

9. 061-283-6003 Adjust Indirect Fire

1. Formulate and transmit the initial call for fire.

a. Locate the target by grid coordinates (within 250 meters of the actual location).

b. Determine the direction to the target, plus or minus 100 mils.

c. Transmit the call for fire to the FDC on the fire net in three parts:

(1) Observer identification and warning order.

(2) Target location (grid).
(3) Target description.

d. Complete above tasks in sequence and within three minutes.
** 2. Determine Observer-Target (OT) factor.
3. Adjust fire onto the target using the successive bracketing method.

** a. Spot each round when it impacts as landing over, short, right, or left of the target.

** b. Determine deviation corrections of less than 10 meters and ignore deviation

corrections of less than 30 meters.

c. Transmit corrections to the FDC within thirty seconds after the previous round
impacts.

** d. Continue splitting the range bracket until you split a 100-meter bracket or until you

observe a range correct.
4. Observe the results of the fire for effect. If needed, transmit refinements. End the mission and the surveillance.
** 5. Perform performance measure 1 within three minutes and each subsequent correction within thirty seconds.

10. 081-COM-0101 Request Medical Evacuation

1. Collected all information needed for the MEDEVAC request line items 1 through 9.
** 2. Recorded the information using the authorized brevity codes.
3. Transmitted the MEDEVAC

** Indicates performance measures that result in automatic failures of the task.

Passed Failed

Reason (s) for Failure:

Scorers Signature:

Date:
Previous Edition is Obsolete

Is this a Yes:
Retest?

No:
Ver 2.0

APPENDIX F

PCI/PCC Area, Candidates will prep equipment, inspect and

stow hand grenades, load the ACIP radio. (time will start
when Candidate fills the radio)

Candidate will cross the LD and complete tasks; Move Under Direct
Fire, conduct three medical tasks, Employ Hand Grenades, Send a
Spot Report, Adjust Indirect Fire, and Request Medical Evacuation.
OPFOR will engage the Candidate in order to set the conditions for
the Candidate to begin IMT. As the Candidates maneuver down the
lane they will encounter friendly forces that require medical attention.
The Candidate will be required to throw his hand grenades 35 meters
killing the enemy threat. As the Soldier continues to maneuver the
ITT lane, the condition will be set for the desired performance of the
tasks on the lane.

Page: 119

APPENDIX G
HOLD ALL QUESTIONS
OPERATIONS ORDER: EIB Lane Alpha
REFERENCE: CAMP DARBY SPECIAL MAPSHEET (1:50,000)
TIME ZONE USED THROUGHOUT THE ORDER: ROMEO
1. Situation. Enemy forces have been operating in AO Shelby IOT disrupt friendly forces freedom
of maneuver.

a. Enemy forces.

Disposition. Enemy forces from the Taliban have been reported to operate in and

around the town of Damascus performing harassing fires to military personnel.


Composition. They use M4 rifles and US Style HMMWV.


Strength. Normally they operate in 1 to 2 man teams.


Capabilities. They are capable of reinforcing up to a platoon size element within 20
min.

b. Friendly forces.

1. US Forces will patrol on the outskirts of AO Shelby and perform clearing

operations in the vicinity of the town of Damascus IOT restore military freedom of
movement.
2. Mission. MCoE will destroy enemy personnel and equipment IVO 16 SF020808 NLT 01
October 2013 IOT deny freedom of maneuver of enemy personnel on OBJ Falcon.
3. Execution. Intent. MCoE will accomplish this by conducting a map reconnaissance to identify
key terrain features, clearing the objective, and establishing a defense in the outlying areas of Town
Damascus.

c. Concept of the Operation. The purpose of this operation is to deny enemy freedom of

maneuver on OBJ Falcon. We will accomplish by conducting a movement to contact.

Decisive to this operation is the destruction of enemy combatants and equipment. This is

decisive because it will allow friendly force freedom and maneuver on OBJ Falcon. 1st

SQD, 2nd PLT, ME, clears OBJ Falcon to destroy enemy combatants and equipment. 2nd

SQD, 2nd PLT, SE1, screens along the right flank to allow the ME freedom of maneuver.

3rd SQD, 2nd PLT, SE2, screens along the left flank to allow the ME freedom of maneuver.

The endstate of this operation is defined as all enemy and equipment is destroyed, key terrain
Page: 120

is secured, and friendly elements are prepared for future operations.

Maneuver. This operation will be conducted in four phases. Phase 1

is reconnaissance and preparation, Phase 2 is movement to OBJ Falcon, Phase 3 is

the clearance of OBJ Falcon, and Phase 4 is consolidation and reorganization.

Phase 1 is currently ongoing. During this phase you will prep men, weapons,

and equipment. This is critical because it will allow you to develop a

plan to clear OBJ Falcon. This phase ends when you cross the LD.


Phase 2 begins when you cross the LD. During this phase you will conduct

movement from the AA, across the LD, to OBJ Falcon. If you encounter any

friendly, civilian or enemy combatants you will treat them in accordance with

the Geneva Convention. This phase ends once contact is made with the
enemy.


Phase 3 begins once contact is made with the enemy. During this phase you

will have priority with the indirect capabilities. This phase ends once OBJ
Falcon is secure.


Phase 4 begins once OBJ Falcon is secure. During this phase you will

consolidate and reorganize as needed and send all reports to higher . This

phase ends when all men, weapons, and equipment have been evacuated from
the OBJ area.
4. Service and Support.

1 ASIP Radio

1 SKU

2 x Fragmentary Hand Grenades.

1 Magazine of 5.56mm

1 Compass, 1 map, 1 protractor, 1 set of map markers

1x M24 Binoculars.

1 Tourniquet

1 CLS Bag
5. Command and Signal.

Freqs/call signs. Participants in each lane are given the following freqs/call signs.

Lane 1. ALPHA 1 (ONE).

Lane 2. ALPHA 2 (TWO).

Lane 3 ALPHA 3 (THREE).

SOLDIER IS TALKING TO: ALPHA 6 (A6)
FREQUENCIES

Lane Frequency: M66.35/M68.85
You are not allowed to list out the tasks being conducted on the lane in the OPORDER.
Page: 121

APPENDIX H
SWORN STATEMENT

For use of this form, see AR 190-45; the proponent agency is PMG.
AUTHORITY:
PRINCIPAL PURPOSE:

ROUTINE USES:




DISCLOSURE:
1. LOCATION

PRIVACY ACT STATEMENT

Title 10, USC Section 301; Title 5, USC Section 2951; E.O.9397 Social Security Number (SSN).
To document potential Criminal activity involving the U.S. Army, and to allow Army officials to maintain
discipline, law and order through investigation of complaints and incidents.
Information provided may be further disclosed to federal, state, local, and foreign government law enforcement
agencies, prosecutors, courts, child protective services, victims, witnesses, the Department of Veterans Affairs, and
the Office of Personnel Management. Information provided may be used for determinations regarding judicial or
non-judicial punishment, other administrative disciplinary actions, security clearances, recruitment, retention,
placement, and other personnel actions.
Disclosure of your SSN and other information is voluntary.
2. DATE (YYYYMMDD) 3. TIME
4. FILE NUMBER

Fort Benning, Ga

5. LAST NAME, FIRST NAME, MIDDLE NAME

Doe, John A.

8. ORGANIZATION OR ADDRESS
9.

LTC John A. Doe

I,

2013/10/01

6. SSN

1300 HRS

123-45-6789

7. GRADE/STATUS

0-5

, WANT TO MAKE THE FOLLOWING STATEMENT UNDER OATH:

On 1 October 2013, I certify that all Soldiers have met all of the below requirements IAW USAIS PAM 350-6 DtD
October 2013, to participate in the Expert Infantryman Badge Testing during the period of the 1st through 5th of
October 2013.

a. Is an active member of the U.S. Army, ARNG, or USAR. South Korean Soldiers assigned by paragraph and
line number to U.S. Army Infantry units are eligible to test for the EIB.

b. Enlisted personnel must possess a CMF 11 or CMF 18 MOS as their primary MOS. Personnel holding
the 18D MOS are not eligible to test for the EIB. Secondary and additional Military Occupational Skills will
not be considered in meeting this requirement.

c. Officers must be branch qualified as Infantry or Special Forces. Officers who are branch detailed to the
Infantry may test for the EIB as long as they have completed the Infantry Officer Basic Course and are still
on loan to the Infantry from the donor branch on Page: 17 accordance with AR 614-100.

d. Has met all height and weight requirements outlined in AR 600-9.

e. Has qualified expert with the M4 Carbine or M16 Rifle on a 300 meter RETS range within six months
of testing for the EIB in accordance with FM 3-22.9. ARNG and USAR personnel must have qualified
within one year of testing for the EIB. This prerequisite cannot be used to offset any testing requirements
which occur within the EIB process. In instances where a 300 meter RETS range is not accessible to the
unit, qualification on the ALT-C course is acceptable; however, the unit will need to justify their inability
to access a 300 meter RETS range via memorandum to the Test Manager. ALT-C is not permitted in
order to provide an additional attempt for weapons qualification for personnel who have been afforded an
opportunity to qualify on a 300 meter RETS range prior to EIB testing.
f. Is a volunteer for testing and has received the recommendation of their current commander to participate
in testing.

10. EXHIBIT

11. INITIALS OF PERSON MAKING STATEMENT

JAD
PAGE 1 of __2__ PAGES
ADDITIONAL PAGES MUST CONTAIN THE HEADING STATEMENT OF _____ TAKEN AT _____ DATED _____
THE BOTTOM OF EACH ADDITIONAL PAGE MUST BEAR THE INITIALS OF THE PERSON MAKING THE STATEMENT, AND PAGE
NUMBER MUST BE INDICATED.
APD V1.00
DA FORM 2823, DEC 1998, IS OBSOLETE
DA FORM 2823, NOV 2006

STATEMENT OF

LTC John A. Doe

TAKEN AT

Fort Benning

DATED

2013/10/01

9. STATEMENT (CONTINUED)

JAD
JAD
JAD
JAD

AFFIDAVIT
I,
LTC JOHN A. DOE
, HAVE READ OR HAVE HAD REAT TO ME THIS STATEMENT WHICH BEGINS ON PAGE 1, AND
ENDS ON PAGE __2__. I FULLY UNDERSTAND THE CONTENTS OF THE ENTIRE STATEMENT MADE BY ME. THE STATEMENT
IS TRUE. I HAVE INITIALED ALL CORRECTIONS AND HAVE INITIALED THE BOTTOM OF EACH PAGE CONTAINING THE
STATEMENT. I HAVE MADE THIS STATEMENT FREELY WITHOUT HOPE OF BENEFIT OR REWARD, WITHOUT THREAT OF
PUNISHMENT, AND WITHOUT COERCION, UNLAWFUL INFLUENCE, OR UNLAWFUL INDUCEMENT.
(Signature of Person Making Statement)
WITNESSES:

MSG Hancock, Shane

MSG Haskins, Jeffrey L.
ORGANIZATION OR ADDRESS

1 Karker Street
Suite 6100
Fort Benning, Ga 39105
ORGANIZATION OR ADDRESS

INITIALS OF PERSON MAKING STATEMENT

JAD

DA FORM 2823, NOV 2006

Subscribed and sworn to before me, a person authorized by law

to administer oaths, this __1st__ day of ____October_____,
at 1300___________________________________________

(Signature of Person Administering Oath)

(Typed Name of Person Administering Oath)

(Authority Administer Oath)

PAGE __2__ OF __2__ PAGES

APD V1.00

United States Army

Certificate of Achievement
Be it known that

Shane Hancock
Has successfully completed
The Expert Infantryman Badge Testing
And in testimony thereof he is awarded the

Expert Infantryman Badge

Given at Fort Benning, GA.
On this 1st day of May 2014
Timothy A. Guden
Command Sergeant Major
U.S. Army Infantry School

Test No.: 14.05.1A

Order No.: 14152-1

David B. Haight
Colonel, Infantry
Commandant