433 MHz RF module with Arduino Tutorial 1

If you are looking for a way to communicate between Arduinos, but don't have much cash at
your disposal, then look no further. These RF modules are not only affordable, but easy to use.
They are much easier to set up than an XBee, plus you can use them without the need of a
special shield. Before you rush out and buy a ton of these modules, make sure that you are not
breaking any radio transmission laws in your country. Do your research, and buy them only if
you are allowed to use them in your area. There are a few [OPTIONAL] libraries that can be
used to help you and your particular project.

Virtual Wire (at ICStation)

RadioHead - which supercedes VirtualWire

RC-Switch for communication with remote controls

Ninjablocks 433 Utilities

I will mention at this point however, that I did NOT use any libraries in this particular tutorial.
That's right. I will show how easy it is to transmit data from one arduino to another using these
RF
modules
WITHOUT
libraries.
Also if you are looking for an easy way to record the signals and play them back without a
computer
then
jump
to this
tutorial.

Video

Project 1- RF Blink
Firstly we need to test if the RF modules are working. So we will design a very simple transmit
and receive sketch to test their functionality. We will use the Arduino's onboard LED to show
when the transmitter is transmitting, and when the other Arduino is receiving. There will be a
slight delay between the two Arduinos. You can solder an antenna onto these modules,
however I did not do this, I just kept the modules close together (1-2cm apart). I also found that
I was getting better accuracy when I used 3V instead of 5V to power the receiver. While using
5V for VCC on the receiver, I would get a lot of interference, however with 3V, I hardly got any
noise. If you find you are getting unpredictable results, I would suggest you switch to 3V on the
receiver and move the transmitter and receiver modules right next to each other. Remember
this is just a check... you can experiment with an antenna or a greater distance afterwards.
Here

are

the

parts

that

you

will

need

to

carry

out

this

Parts Required
2 x Arduino UNO or compatible boards

Breadboard

Wires

RF Module (433 Mhz) - Transmitter and Receiver pair or the 315 Mhz version

The Transmitter and Receiver Fritzing Sketch

project:

The Transmitter
The transmitter has 3 pins,

Notice the pin called "ATAD". It took me a while to figure out what ATAD stood for, when
I suddenly realised that this was just a word reversed. It should be DATA (not ATAD).
Nevertheless, this is the pin responsible for transmitting the signal. We will make the

Arduino's onboard LED illuminate when the transmitter pin is HIGH, and go off when
LOW as described in the following table.

And this is the Arduino Sketch to carry out the data transmission.

Arduino sketch - Transmitter

/*
RF Blink - Transmit sketch

Written by ScottC 17 Jun 2014

Arduino IDE version 1.0.5

Website: http://arduinobasics.blogspot.com

Transmitter: FS1000A/XY-FST

Description: A simple sketch used to test RF transmission.

8
9

------------------------------------------------------------- */

10
11 #define rfTransmitPin 4

//RF Transmitter pin = digital pin 4

12 #define ledPin 13

//Onboard LED = digital pin 13

13
14 void setup(){

15

pinMode(rfTransmitPin, OUTPUT);

16

pinMode(ledPin, OUTPUT);

17 }
18
19 void loop(){
20

for(int i=4000; i>5; i=i-(i/3)){

21

digitalWrite(rfTransmitPin, HIGH);

//Transmit a HIGH signal

22

digitalWrite(ledPin, HIGH);

//Turn the LED on

23

delay(2000);

//Wait for 1 second

24
25

digitalWrite(rfTransmitPin,LOW);

//Transmit a LOW signal

26

digitalWrite(ledPin, LOW);

//Turn the LED off

27

delay(i);

28

//Variable delay

29 }

The Receiver

If all goes to plan, the onboard LED on this Arduino should light up (and go off) at the

same time as the onboard LED on the transmitting Arduino. There is a chance that the
receiver may pick up stray signals from other transmitting devices using that specific
frequency. So you may need to play around with the threshold value to eliminate the
"noise". But don't make it too big, or you will eliminate the signal in this experiment. You
will also notice a small delay between the two Arduinos.

Arduino sketch - Receiver

/*

RF Blink - Receiver sketch

Written by ScottC 17 Jun 2014

Arduino IDE version 1.0.5

Website: http://arduinobasics.blogspot.com

Receiver: XY-MK-5V

Description: A simple sketch used to test RF transmission/receiver

8 .
9

------------------------------------------------------------- */

10
11 #define rfReceivePin A0

//RF Receiver pin = Analog pin 0

12 #define ledPin 13

//Onboard LED = digital pin 13

13
14 unsigned int data = 0;

// variable used to store received data

15 const unsigned int upperThreshold = 70;

//upper threshold value

16 const unsigned int lowerThreshold = 50;

//lower threshold value

17
18 void setup(){
19

pinMode(ledPin, OUTPUT);

20

Serial.begin(9600);

21 }
22
23 void loop(){
24

data=analogRead(rfReceivePin);

//listen for data on Analog pin 0

if(data>upperThreshold){
25

digitalWrite(ledPin, LOW);

//If a LOW signal is received, turn

26 LED OFF
27

Serial.println(data);

28

29
30

if(data<lowerThreshold){

31

digitalWrite(ledPin, HIGH);

//If a HIGH signal is received, turn

32 LED ON
33

Serial.println(data);

34

}
}

When a HIGH signal is transmitted to the other Arduino. It will produce an AnalogRead = 0.
When a LOW signal is transmitted, it will produce an AnalogRead = 400.
This may vary depending on on your module, and voltage used.
The signals received can be viewed using the Serial Monitor, and can be copied into a
spreadsheet to create a chart like this: