Hydraulic System Design

Hydraulic Dos and Donts
Delta Computer Systems, Inc.
DOs and DON'Ts of Hydraulic Position Control

System Design
Fluid power systems are capable of very high performance motion control. A well-designed
closed-loop hydraulic actuator can position heavy loads to accuracies better than 0.0005. Fast,
precise motion requires a controller with specialized fluid power capabilities, such as the easy-touse RMC family from Delta Computer Systems, Inc. (www.deltamotion.com). However, a welldesigned hydraulic system is equally important. This document provides a concise list of the
considerations for high performance closed-loop hydraulic motion control systems.*
Diagram of a
typical hydraulic
system.
Note:
Pressure transducers
are not required for
position-only control.
DOs:
1. Use Servo-Quality Valves
2.
3.
4.
5.
6.
7.
Use servo-quality valves or "proportional" valves with zero overlap spools and linear
flow per input response. See DONT #2.
Place Valves on Cylinders
Mount valves on the end and on top of the cylinders. Keep the trapped volume of oil
between the valve and the piston as small as possible. See DONT #1.
Use Accumulators
Use an accumulator, placed as close to the valves as reasonably possible. It should be
sized at least 10 times larger than the change in the volume of oil.
Pre-charge Accumulator
Pre charge the accumulator to 80% of system pressure. Any oil in the accumulator that is
not being used reduces its effectiveness. The nitrogen bubble should be as large as
possible as long as there is always some oil in the accumulator.
Size Pump Correctly
Size the pump to the average oil flow plus 10%. There is no need to size the pump for
peak load when using an accumulator.
Size Cylinders Correctly
Use cylinders with a diameter large enough to get the desired acceleration / deceleration
rates.
Size Hydraulic Lines Correctly
Use adequate pressure and return lines with a minimum number of 45 and 90 joints.
*For an in-depth treatment of hydraulic design for high-performance motion control,
refer to Fluid Power Motion Control: A guide to Practical Design written by Delta's Peter
Nachtwey. Go to http://www.deltamotion.com/other/designguide/register.php to request your
free copy.
Motion Control and More
www.deltamotion.com
8. Size Valve Correctly

Valves should be sized large enough to allow the system to accelerate at the desired rate
and the maximum desired speed. Remember that at high flow the pressure drop across the
valve will be large and the pressure drop across the piston will drop, reducing the ability
to accelerate.
9. Use a Suitable Motion Controller
Hydraulic control requires parameters, transducer interfaces, and algorithms not available
on motion controllers intended for motor control. Use Deltas RMC motion controllers
for high performance control of hydraulic, electric and pneumatic systems.
10. Use a Precision Position Feedback Transducer
Mount a magnetostrictive linear displacement transducer (MDT or LDT) in the hydraulic
cylinder. Cylinders can be ordered so they are MDT ready. MDTs can be ordered with
Start Stop, PWM, SSI, or analog outputs. (Analog is not recommended for best control
because of susceptibility to noise, which can significantly reduce resolution.)
DON'Ts:
1. Flexible Hose between Valve and Cylinder
2.
3.
4.
5.
6.
Do not use flexible hose between the valve and the cylinder. THIS IS VERY
IMPORTANT! Flexible hose between the valve and cylinder will result in difficult
tuning and poor control. See DO #2.
Overlapped Spools
Do not use valves with overlapped (closed-center) spools. ALSO VERY IMPORTANT!
See DO #1. When an overlapped spool shifts from one side to another to change direction
of the motion, the system will come to a stop with a thud, leading to difficult tuning and
poor control around critical zero point. With a zero-lapped spool, the system very
smoothly transitions between opposite directions of control.
Separate Valve Amplifier
Avoid valves with separate amplifiers unless you are able to set up the amplifier properly.
Many valves have the electronics built in the valve and are set up by the factory.
Run Wires in Same Raceways
Do not run the high current Pulse Width Modulated signal, from the amplifier to the
valve, in the same conduit or raceway as the wires from the position feedback transducer.
See DON'T #3.
Go Half-way on Closed-loop Control
Some people are scared of closed-loop motion control, so they put two different valves
on their system one for open-loop control, and one for closed loop control, along with
plumbing to switch between the two. This makes a very complicated system, requiring
more plumbing and programming and maintenance than a simple closed-loop system.
Closed-loop control is simple and easy. Attend a Delta training course to learn more
about hydraulic motion controllers!
Counter-balance Valves
Do not use counter-balance valves. They counteract the motion controller. If you need to
have a safety valve to keep a vertical load from falling, use a blocking valve between the
valve and the cylinder. Close the valve when you need the load to be stopped. Open it
when you want motion control.
www.deltamotion.com
About Deltas RMC Motion Controllers

Deltas motion controllers provide precise closed-loop position, velocity, pressure, force, and
position-pressure or position-force control for electric, hydraulic, and pneumatic applications.
RMC100 Series (2-8 axes)

Deltas multi-axis motion controllerspossibly the
most versatile pre-programmed motion controllers on
earthuse them for all your motion needs! The
RMC100 Series includes the flagship RMC100/101
controllers and the new RMC150/151 controllers.
RMC100/101
RMC150/151
RMC70 Series(1-2 axes)

Even more value for one and two-axis applications.
RMC70
A stand-alone motion controller frees up space in the PLC (in the program, processing power, and
rack), and the motion control is done at the loop time of the RMC, which is typically much faster
than the PLC. The RMCs also have superior plotting and diagnostic capabilities
All of Deltas legacy products are still serviced and available for sale to support existing designs.
Benefits of Deltas RMC Series Motion Controllers include:
High Performance: Features such as synchronized moves, splines, position-pressure or

position-force control, and fast user programs provide higher throughput, improved
quality, and reduced machine wear and breakage through optimized control.
Communication Connectivity: Support for numerous industrial standards provide
efficient communications to the PLC of your choice. Communication options include
EtherNet, serial RS-232/485, Profibus , discrete I/O, and Modbus Plus.
Transducer Connectivity: The very versatile RMC family connects to virtually all
industrial feedback transducers.
Quick to Set Up and Optimize: Deltas command-driven programming, graphing tools,
and new Tuning Wizard literally reduce project implementation time from weeks to days.
Responsive Support: Bring us your challenges. We strive to be the industry leaders in
responsive support and training, before, during and after the sale on legacy as well as
newer products.
Summary: Maximize ROI and minimize lifecycle costs. Look to Delta for innovative
technology, great products, responsive service, and lasting value.
Learn More
To learn more about Deltas motion controllers, visit www.deltamotion.com, or call
360-254-8688 to schedule a half-hour phone demo of an RMC.
You can also download the RMCTools software from Deltas website, and connect to a live RMC
via the web.
www.deltamotion.com

Hydraulic System Design

Uploaded by

Copyright:

Available Formats

Hydraulic System Design

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hydraulic System Design

Uploaded by

Copyright:

Available Formats

Hydraulic Dos and Donts

Delta Computer Systems, Inc.

DOs and DON'Ts of Hydraulic Position Control

Motion Control and More

Hydraulic Dos and Donts

Delta Computer Systems, Inc.

8. Size Valve Correctly

Motion Control and More

Hydraulic Dos and Donts

Delta Computer Systems, Inc.

About Deltas RMC Motion Controllers

RMC100 Series (2-8 axes)

RMC70 Series(1-2 axes)

High Performance: Features such as synchronized moves, splines, position-pressure or

Motion Control and More

You might also like