Modal Analysis of Cantilever Beam Structure Using Finite Element Analysis and Experimental Analysis

2015
American Journal of Engineering Research (AJER)

e-ISSN: 2320-0847 p-ISSN : 2320-0936
Volume-4, Issue-10, pp-178-185
www.ajer.org
Research Paper
Open Access
Modal analysis of cantilever beam Structure Using Finite

Element analysis and Experimental Analysis
S. P. Chaphalkar1, Subhash. N. Khetre2, Arun M. Meshram3
1
Head of Department, Department of Automobile Engineering, Pimpri Chinchwad, Polytechnic, Pune

2
Assistant professor, Department of Mechanical Engineering, RSCOE, Tathawade, Pune
3
Assistant professor, Department of Mechanical Engineering, RSCOE, Tathawade, Pune
ABSTRACT: The modal analysis is presented in this paper some basic concepts of modal analysis of
transverse vibration of fixed free beam. It is described an experimental apparatus and the associated theory
which allows to obtain the natural frequencies and modes of vibration of a cantilever beam. The concept of
modal analysis plays an important role in the design of practical mechanical system. So it becomes important to
study its effects on mechanical system for different frequency domain i.e. low, medium and high frequency. This
paper focuses on the numerical analysis and experimental analysis of transverse vibration of fixed free beam
and investigates the mode shape frequency. All the frequency values are analyzed with the numerical approach
method by using ANSYS finite element package has been used. The numerical results are in good agreement
with the experimental tests results.
Keywords - Finite Element analysis, Modal analysis, Fixed Free Beam, Experimental Analysis, Free vibration.
I.
INTRODUCTION
In the past two decades, modal analysis has become a major technology in the quest for determining,
improving and optimizing dynamic characteristics of engineering structures. Not only has it been recognized in
mechanical and aeronautical engineering, but modal analysis has also discovered profound applications for civil
and building structures, biomechanical problems, space structures, acoustical instruments, transportation and
nuclear plants. The Free vibration takes place when a system oscillates under the action of forces integral in the
system itself due to initial deflection, and under the absence of externally applied forces. The system will vibrate
at one or more of its natural frequencies, which are properties of the system dynamics, established by its
stiffness and mass distribution. In case of continuous system the system properties are functions of spatial
coordinates. The system possesses infinite number of degrees of freedom and infinite number of natural
frequencies. Vibration analysis of fixed free Beam like components has been an active research subject and
numerous technical papers have been published. For to calculating the natural frequencies and mode shapes of a
structure modal analysis method is used. This method determined the dynamic response of complicated
structural dynamic problems.
In general, applications of modal analysis today cover a broad range of objectives identification and
evaluation of vibration phenomena, validation, structural integrity assessment, structural modification, and
damage detection. In engineering design, it is important to calculate the response quantities such as the
displacement, stress, vibration frequencies, and mode shapes of given set of design parameters. The study of
mathematical models which involve physical and geometric parameters such as mass density , elastic modulus
E, Poissons ratio v, lengths, and cross-section shape characteristics. In many practical engineering applications,
these parameters frequently do not have well-defined values due to non-homogeneity of the mass distribution
geometric properties or physical errors, as well as variation arising from the assembly and manufacturing
processes.
II.
MAIN OBJECTIVES:
All the Vehicles, aircraft and home appliances structures are made up of fixed beam with one end free or
combination of fixed beams so it becomes necessary to study fixed beam vibration. The following are main
objective of yoke design.
www.ajer.org
Page 178

1.
2.
3.
2015
A detailed understanding of function and configuration of fixed beam with one end free
To Analysis of fixed beam with one end free using FEA Method.
To Analysis of fixed beam with one end free using Experimental method.
III. NUMERICAL ANALYSIS BY USING ANSYS:

3.1 Basic steps of finite element analysis:
There are three basic steps involved in this procedure,
1. Pre Processor (Building the model (or) Modeling)
2. Solution (Applying loads and solving)
3. Post Processor (Reviewing the results)
3.2. Numerical Approach for Transverse Vibration of Fixed Free Beam:
We shall now investigate the free vibration of fixed free beam using the ANSYS program, a
comprehensive finite element package. We use the ANSYS structural package to analyse the vibration of fixed
free beam. Finite element procedures at present very widely used in engineering analysis. The procedures are
employed extensively in the analysis of solid and structures and of heat transfer and fluids and indeed, finite
element methods are useful in virtually every field of engineering analysis.
3.3. Description of the finite element method:
The physical problem typically involves an actual structure or structural component subject to certain
loads. The idealization of the physical problem to a mathematical model requires certain assumptions that
together lead to differential equations governing the mathematical model. Since the finite element solution
technique is a numerical procedure, it is necessary to access the solution accuracy. If the accuracy criteria are
not met, the numerical solution has to be repeated with refined solution parameters until a sufficient accuracy is
reached.
3.4. Important features of finite element method
The following are the basic features of the finite element method: Division of whole in to parts, which
allows representation of geometrically complex domains as collection of simple domains that, enables a
systematic derivation of the approximation functions. Derivation of approximation functions over each element
the approximation functions are algebraic polynomials that are derived using interpolation theory.
3.5. Boundary Conditions:
The meshed model is then analyzed (static) and the boundary conditions are:
One end is fixed (All DOF).
3.6. Numerical (FEA) Results:
The dimensions and the material constant for a uniform fixed free beam (cantilever beam) studied in
this paper are: Material of beam = mild steel, Total length (L) = 0.8 m , width (B) = 0.050 m, height (H) = 0.006
m, Youngs Modulus (E) = 210 x 10 9, mass density = 7856 kg/ m3. Poisson Ratio= 0.3. The numerical results
were found out by using the ANSYS program as shown in Table 3. The Numerical (FEA) values obtained are
7.67 Hz and 688.89 Hz for first and last modes respectively.
Table 1: Numerical frequency from ANSYS
www.ajer.org
Mode
Numerical frequency from ANSYS program in Hz
1
2
3
4
5
6
7
8
9
10
7.6769
48.1
63.585
134.69
229.16
264.01
391.46
436.63
652.62
688.89
Page 179
2015
Fig. 1 : Geometry of fixed beam at one end
Fig. 2 : Meshing of fixed beam at one end
Fig. 3 :Total Deformation-10
Fig. 4 : Total Deformation-9
www.ajer.org
Page 180
www.ajer.org
2015
Page 181
2015
Graph. 1 : Graphical representation of the modal frequencies
IV. EXPERIMENTAL ANALYSIS OF TRANSVERSE

VIBRATION OF FIXED FREE BEAM:
4.1 Experimental Setup:
The dimensions and the material constant for a uniform fixed free beam (cantilever beam) studied in
this paper are: Material of beam = mild steel, Total length (L) = 0.8 m , width (B) = 0.050 m, height (H) = 0.006
m, Youngs Modulus (E) = 210 x 10 9, mass density = 7856 kg/ m3. Poisson Ratio= 0.3
A beam which is fixed at one end and free at other end is known as cantilever beam. From elementary
theory of bending of beams also known as Euler-Bernoulli. In experiment we will use digital phosphor
oscilloscope (Model DPO 4035) for data acquisition.
Fig. 13. Free vibration for cantilever

Accelerometer is a kind of transducer to measure the vibration response (i.e., acceleration, velocity and
displacement). Data acquisition system acquires vibration signal from the accelerometer, and encrypts it in
digital form. Oscilloscope acts as a data storage device and system analyzer. It takes encrypted data from the
data acquisition system and after processing (e.g., FFT), it displays on the oscilloscope screen by using analysis
software. Fig. shows an experimental setup of the cantilever beam.
www.ajer.org
Page 182
Fig. 14. Experimental setup
2015
Fig. 15. Closed View of Accelerometer
It includes a beam specimen of particular dimensions with a fixed end and at the free end an accelerometer is
clamped to measure the free vibration response. The fixed end of the beam is gripped with the help of clamp.
For getting defined free vibration cantilever beam data, it is very important to confirm that clamp is tightened
properly; otherwise it may not give fixed end conditions in the free vibration data.
4.2 Experimental Procedure:
[1] A beam of a particular material (steel, aluminum), dimensions (L, w, d) and transducer (i.e., measuring
device, e.g. strain gauge, accelerometer, laser vibrato meter) was chosen.
[2] One end of the beam was clamped as the cantilever beam support.
[3] An accelerometer (with magnetic base) was placed at the free end of the cantilever beam, to observe
the free vibration response (acceleration).
[4] An initial deflection was given to the cantilever beam and allowed to oscillate on its own. To get the
higher frequency it is recommended to give initial displacement at an arbitrary position apart from the
free end of the beam (e.g. at the mid span).
[5] This could be done by bending the beam from its fixed equilibrium position by application of a small
static force at the free end of the beam and suddenly releasing it, so that the beam oscillates on its own
without any external force applied during the oscillation.
[6] The free oscillation could also be started by giving a small initial tap at the free end of the beam.
[7] The data obtained from the chosen transducer was recorded in the form of graph (variation of the
vibration response with time).
[8] The procedure was repeated for 5 to 10 times to check the repeatability of the experimentation.
[9] The whole experiment was repeated for same material, dimensions, and measuring devices.
[10] The whole set of data was recorded in a data base.
4.3 Experimental Results:
To observe the natural frequencies of the cantilever beam subjected to small initial disturbance
experimentally up to third mode, the experiment was conducted with the specified cantilever beam specimen.
The data of time history (Displacement-Time), and FFT plot was recorded. The natural frequencies of the
system can be obtained directly by observing the FFT plot. The location of peak values relates to the natural
frequencies of the system. Fig. below shows a typical FFT plot.
Table 2: Mode shape frequency by Using Experimental Method
www.ajer.org
Mode
Experimental frequency in Hz
1
2
3
4
5
6
7
8
9
10
7.6769
48.1001
63.5854
134.6906
229.1626
264.0133
391.4638
436.6341
652.6247
688.8954
Page 183
2015
The present experimental results are based on the assumption that one end of the cantilever beam is
properly fixed. However, in actual practice it may not be always the case because of flexibility in support. The
experimental values obtained are 7.6769 Hz and 688.8954Hz for first and last modes respectively.
V.
SUMMARY OF RESULT
The numerical (FEA) calculated natural frequency and the experimental are found good agreement.
The correction for the mass of the sensor will improve the correlation better. The present numerical (FEA)
results and experimental results is based on the assumption that one end of the cantilever beam is properly fixed.
However, in actual practice it may not be always the case because of flexibility in support. The summary of
analysis of result summarized as show in table 3.
Table 3: Summary of result in Percentage error
Mode
Numerical (FEA)
frequency in Hz
Experimental
frequency in Hz
Percentage Error
%
1
2
3
4
5
6
7
8
9
7.6769
48.1
63.585
134.69
229.16
264.01
391.46
436.63
652.62
7.6769
48.1001
63.5854
134.6906
229.1626
264.0133
391.4638
436.6341
652.6247
0
0.0001
0.0004
0.0006
0.0026
0.0033
0.0038
0.0041
0.0047
10
688.89
688.8954
0.0054
VI.
CONCLUSION
We have studied the free vibration of fixed free beam by using experimental approach and the
numerical (FEA) approach using the ANSYS program, it has been found that the relative error between these
two approaches are very minute. The percentage error between the numerical (FEA) approach and the
experimental approach are allowed up to 5% to 7%. Firstly we obtained the results for mode shape frequency
numerically (FEA) and analyzing this mode shape frequency by experimental on the fixed free beam which we
were used in this paper. The numerical study using the ANSYS program allows investigates the free vibration of
fixed free beam to find out mode shape and their frequencies with high accuracy. The experimental mode shape
frequency values are also compared with the numerical (FEA) results that are obtained from the ANSYS
software. It is observed that the numerical (FEA) results values are in-tuned with the experimental values. The
procedure and experimental models that are used in this paper are very useful to researchers who willing to
work experimental analysis.
VII.
ACKNOWLEDGEMENTS
We gratefully acknowledge department of mechanical engineering of Rajarshri College of

Engineering, Tathawade, Pune (India), for technical support and providing the research facilities. Their help
and dedication toward our work and related research, also their library staff and expert for their directly &
indirectly help, support and excellent co-operation.
REFERENCES
Journal Papers:
[1] Thin-Lin Horng, Analytical Solution of Vibration Analysis on Fixed-Free Single-Walled Carbon Nanotube-Based Mass Sensor,
Journal of Surface Engineered Materials and Advanced Technology, 2012; 2(1): PP 47-52.
[2] J S Wu And H-M Chou, Free Vibration Analysis Of A Cantilever Beam Carrying Any Number Of Elastically Mounted Point Masses
With The Analytical-And-Numerical-Combined Method, Journal of Sound and Vibration, 1998, 213(2): PP 317-332.
[3] Tarsicio Beleandez, Cristian Neipp, Numerical and Experimental Analysis of a Cantilever Beam: a Laboratory Project to Introduce
Geometric Nonlinearity in Mechanics of Materials, Int. J. Engng Ed., 2003;19(6): PP 885 -892.
www.ajer.org
Page 184
2015
[4] J. J. Wu and A. R. Whittaker, The Natural Frequencies and Mode Shapes Of A Uniform Cantilever Beam With Multiple Two-DOF
Spring Mass Systems, Journal of Sound and Vibration, 1999; 227 (2): PP 361-381.
[5] S.S Queini, A.H Nayfeh, single mode control of a cantilever beam under principal parametric excitation, journal of sound and
vibration 224 (1999) 3347.
[6] M.MKannel, Y.A.Amer, response of parametrically excited one degree of freedom system with non linear damping and stiffness,
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
Physica Scripta 66 (2002) 410-416.

C.Chin, A.H.Nayfeh, W. Lacarbonara, two-to-one internal resonance in parametrically excited buckled beam, AIAA , 1997; 97 : 1081
Haxton RS, Barr ADS. The auto parametric vibration absorber, ASME J.Eng Industry 1972; 94:119-25.
Brian J. Schwarz & Mark H. Richardson," EXPERIMENTAL MODAL ANALYSIS", CSI Reliability Week, Orlando, FL, Oct-1999.
D. Ravi Prasad and D.R. Seshu ''A STUDY OF DYNAMIC CHAARECTERISTIC OF STRUCTURAL MATERIALS USING
MODAL ANALYSIS'' Asian journal of civil engineering.
D.Y. Zheng. Free Vibration Analysis Of A Cracked Beam By finite Element Method. Journal of Sound and Vibration, 2004: 457-475.
Huszar, Zsolt. Vibration of cracked reinforced and prestressed concrete beams Architecture and Civil Engineering, Vol. 6, 2008: 155164
G.M.Owolabi, Swamidas, SeshadrI Crack detection in beams using changes in frequencies and amplitudes of frequency response
functions. Journal of Sound and Vibration, 265(2004) 1-22
M.Behzad, Ebrahimi, A.Meghdari. A continuous vibration theory for beams with a vertical edge crack. Mechanical Engineering, Vol.
17, 2010: 194-204.
E. I. Shifrin. Natural Frequencies Of A Beam With An Arbitrary Number Of Cracks. Journal of Sound and Vibration, 222(3), 1999:
409423
AUTHORS BIOGRAPHY:
Mr. S. P. Chaphalkar:
Currently working as Head of Department, in Automobile
Engineering Department at Pimpri Chinchwad,
Polytechnic, Pune (India) Total experience in teaching 20
Years.
Email: chaphalkar77@gmail.com
Mr. Subhash N. Khetre:

Currently working as a Lecturer, in Mechanical
Engineering Department at Rajarshri Shahu College of
Engineering, Tathawade, Pune (India) Total experience in
teaching 3.5 Years.
Email: subhash2010khetre@gmail.com
Mr. Arun M. Meshram:
Currently working as a Lecturer, in Mechanical
Engineering Department at Rajarshri Shahu College of
Engineering, Tathawade, Pune (India) Total experience in
teaching 6 Years.
Email: arunmeshram82@gmail.com
www.ajer.org
Page 185

Modal Analysis of Cantilever Beam Structure Using Finite Element Analysis and Experimental Analysis

Uploaded by

Modal Analysis of Cantilever Beam Structure Using Finite Element Analysis and Experimental Analysis

Uploaded by

2015

American Journal of Engineering Research (AJER)

American Journal of Engineering Research (AJER)