Scribd
Upload
186 views4 pages

Volcabeats Programming Guide

This manual tells you how to update your Volca Beat. with this information, you can add, or subtract different midi sounds.

Uploaded by

chuckrios
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
186 views4 pages

Volcabeats Programming Guide

This manual tells you how to update your Volca Beat. with this information, you can add, or subtract different midi sounds.

Uploaded by

chuckrios
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 4

System Firmware Update Instructions

Do not playback the system update file on any speaker or headphone system as this could lead to
damage to equipment and/or hearing loss. Korg or any of its affiliates will not accept responsibility for
any damages, personal loss or injury that may result from playback of the file.

What you will need


You will need the following to perform your update.
An audio player or personal computer capable of audio playback
A stereo mini-jack audio cable
AC adapter KA-350 or six AA batteries
Make sure the batteries are brand new if using alkaline or fully charged if using NiMH batteries.
volca beats will not enter update mode if the batteries are depleted.

Preparations
1. Unzip the file volcabeats_updater_0102.zip.
If using an audio player, transfer the file volcabeats_sys_0102.wav from your computer to your audio
player.
Do not playback the system update file on any speaker or headphone system as this could lead
to damage to equipment and/or hearing loss.

2. Check the current version


Turn the power on while pressing the REC button.

volca beats System Firmware Update Instructions

System version 1.00 or 1.01


If the current system is version 1.00 or 1.02, the
display will be lit as shown. Your volca beats is not
up to date. Proceed to step 3.

ver. 1.00

ver. 1.01

System version 1.02


If the current system is version 1.02, the display
will be lit as shown. Your volca beats is already up
to date.

ver. 1.02

3. Connect the audio output of your playback device to the SYNC IN connector on your volca beats.

volca beats System Firmware Update Instructions

Perform the update


1. Turn the power on while pressing the FUNC and PLAY buttons.

UPdt will be displayed to show your volca beats has entered update mode.

2. Start the playback of volcabeats_sys_0102.wav to begin updating.


Make sure the volume of the playback device has been turned up.
STEP LEDs 1-16 will indicate the update progress.

Make sure the update file is played from the beginning.


When using a computer, any other system sounds (e.g. email notification) will cause the update
to fail. Make sure all other applications are shut down and do not operate you computer during
the update.
The update will take approximately two minutes. Do not turn your volca beats off or stop
playback while update is in progress.
If the update fails, the knobs will start blinking. If this happens, observe Tips at the end of this
document and repeat the update from step 1.

3.

When the update has been successfully completed, End will be displayed. Now, turn the power
off.

volca beats System Firmware Update Instructions

4. Go back to step 2 of Preparations and check that your volca beats has been updated.

Tips
Update may fail with some audio players, computers or software. If this is the case, please try with a
different device.
If you are having trouble with the update, please check the following:

Check the current system firmware version. If it has already been updated, you will not be able
to update again (it will also be unnecessary).

Make sure the volume of the playback device has been turned up.
Please note that some devices which have very high output levels may fail because of it. If this
is the case please try turning the volume down and start the update process again.

Make sure all functions that affect the playback sound, such as cross-fade and EQ, are
disabled.

Make sure the update file is played from the beginning.

Check the connection from your playback device to your volca beats.

When using a computer, any other system sounds (e.g. email notification) will cause the update
to fail. Make sure all other applications are shut down and do not operate you computer during
the update.

volca beats System Firmware Update Instructions

You might also like