Glasswool SPI: Technical

Technical Data Sheet
Glasswool SPI
Sectional Pipe Insulation (SPI)
Product description and typical applications
Sectional Pipe Insulation (SPI) is manufactured from rigid glasswool pre-moulded into one-piece
cylindrical sections. These sections are slit along one wall to allow the insulation to be opened and
installed over piping. The high density characteristic provides excellent compression resistance
and enables the product to be used at service temperatures up to 340C. A variety of factory
applied facings are available where extra protection of the outer surface or condensation control
is required, including calico, aluminum foil and Sisalation 450. SPI is available in 1 metre lengths,
faced or unfaced, and with a variety of wall thicknesses to suit standard steel pipes and copper
tube from 12.7mm to 610mm O.D.
Physical characteristics
Nominal Glasswool Density: 64kg/m3
Thickness (mm)
25
38
50
63
75
Thermal conductivity
The thermal conductivity of Glasswool SPI at a mean
temperature* 23C is 0.032 (at 20C it is 0.032 W/mK) when
tested in accordance with ASTM C177. Values of thermal
conductivity may be obtained from the following graph.
*Mean Temperature = T1 + T2
2
Where T1 = temperature of hot side of insulation (C)
Where T2 = temperature of cool side of insulation (C)
Heat transfer calculation service

Given the actual service temperature and the required surface temperature, the appropriate insulation
thickness can be calculated by staff at Fletcher Insulation. Fletcher Insulation can also assist to
determine the optimum insulation thickness quickly and accurately, in an easy-to-read format.
Maximum service temperature

The maximum service temperature for Glasswool SPI is 340C. Where facings are applied,
the temperature tolerance of the facing adhesive limits the surface temperature to 70C. (The
appropriate insulation thickness can be used to limit surface temperature to 70C).
Green star compliant

Fletcher Insulation is committed to providing environmentally sustainable products. Fletcher
Insulation products have Zero Ozone Depleting Potential in both manufacture and composition,
complying with the GreenStar Insulant ODP Emissions credit requirement. Air quality is maintained
with total Volitile Organic Compound (VOC) emissions below quantifiable levels.
ww w.insulation.com.a u
TDS20 Revision 3 Issue Date 11.08.2015 / FI_0143_000911_4
Technical Data Sheet

AS1530.3 Early fire hazard properties of materials
Glasswool SPI exhibits the following characteristics when tested in accordance with AS1530 Part 3.
Ignitability Index
Spread of Flame Index
Heat Evolved Index
Smoke Developed Index
0-1
Moisture absorption
Tested in an atmosphere of 65% relative humidity at 20C in accordance with British Standard
2972. The moisture content of Glasswool SPI is less than 0.1% by volume.
Alkalinity
Glasswool SPI will not support the corrosion of steel. When test in accordance with British
Standard 3958 Glasswool SPI products are slightly alkaline, pH9 (neutral is pH7).
Applications and facings

Glasswool SPI is available with a variety of outer jacket or facing materials which enable its use on
both cold and hot pipe applications.
Cold Applications: To prevent the ingress of water vapour and subsequent potential condensation
or freezing problems, all pipe insulation requires an effective vapour barrier. Glasswool SPI is
available with either Alfoil or Sisalation pre-applied to the sections for this purpose.
Hot Applications: Glasswool SPI does not require a facing for hot work. However, a metal cladding
(generally swaged galvanised or aluminium metal sheathing) is recommended on all outdoor
applications, or on indoor applications where protection from physical damage is required.
Suitability for stainless steel

Under certain conditions, the presence of soluble chlorides may cause stress corrosion cracking of
some stainless steel. Glasswool SPI does not contain significant amounts of chlorides, and
conforms to ASTM C795 Specification for Wicking-type Thermal Insulation for use over Austenitic
Stainless Steel, and is thus considered suitable.
Specification notes
State the following:
Product name and product type - Fletcher Insulation Sectional Pipe Insulation (64kg/m3 density)
Pipe material, outside diameter and length of run.
Insulation thickness required.
Type of finish, facing or surface protection required.
Phone 1300 65 44 44
Email info@insulation.com.au Web ww w.insulation.com.au
Fletcher Insulation 2015. Fletcher Insulation reserves the right to change product specifications without prior
notification. Information in this publication and otherwise supplied to users as to the subject product is based on
our general experience and is given in good faith, but because of the many particular factors which are outside
our knowledge and control and affect the use of products, no warranty is given or is to be implied with respect to
either such information or the product itself, in particular the suitability of the product for any particular purpose.
The purchaser should independently determine the suitability of the product for the intended application. and
are registered trademarks of Fletcher Insulation Pty Limited ABN 72 001 175 355. FBS-1 Glasswool Bio-Soluble
Insulation is a registered trademark of ICANZ Limited used under license by Fletcher Insulation.
TDS20 Revision 3 Issue Date 11.08.2015 / FI_0143_000911_4

Glasswool SPI: Technical

Uploaded by

Glasswool SPI: Technical

Uploaded by

Technical Data Sheet

Heat transfer calculation service

Maximum service temperature

Green star compliant

Technical Data Sheet

Spread of Flame Index

Heat Evolved Index

Smoke Developed Index

Applications and facings

Suitability for stainless steel

You might also like