Stepper Motor

Stepper Motor
BASICS OF STEPPER MOTOR
Of all motors, step motor is the easiest to control. It's handling simplicity is really hard to deny - all
there is to do is to bring the sequence of rectangle impulses to one input of step controller and
direction information to another input. Direction information is very simple and comes down to "left"
for logical one on that pin and "right" for logical zero. Motor control is also very simple - every
impulse makes the motor operating for one step and if there is no impulse the motor won't start.
Pause between impulses can be shorter or longer and it defines revolution rate. This rate cannot be
infinite because the motor won't be able to "catch up" with all the impulses (documentation on specific
motor should contain such information). The picture below represents the scheme for connecting the
step motor to microcontroller and appropriate program code follows.
The key to driving a stepper is realizing how the motor is constructed. A diagram shows the
representation of a 4 coil motor, so named because 4 coils are used to cause the revolution of the
drive shaft. Each coil must be energized in the correct order for the motor to spin.
In Figure 3.3, as in Figure 3.1, boxes are

used to represent switches; a control unit,
not shown, is responsible for providing the
control signals to open and close the
switches at the appropriate times in order to
spin the motors. The control unit is
commonly a computer or programmable
interface controller, with software directly
generating the outputs needed to control the switches.
As with drive circuitry for variable reluctance motors, we must deal with the inductive kick produced
when each of these switches is turned off. Again, we may shunt the inductive kick using diodes, but
now, 4 diodes are required, as shown in Figure 3.4:
Step angle
It is angle through which motor shaft rotates in one step. step angle is different for different motor .
selection of motor according to step angle depends on the application , simply if you require small
increments in rottion choose motor having smaller step angle.
No of steps require to rotate one complete rotation = 360 deg. / step angle in deg.
Steps/second
The relation between RPM and steps per sec. is given by ,

steps or impulses /sec. =(RPM X Steps /revolution ) /60
Pause between impulses can be shorter or longer and it defines revolution rate. This rate cannot be
infinite because the motor won't be able to "catch up" with all the impulses (documentation on specific
motor should contain such information). So referring to RPM value in datasheet you can calculate
steps/sec and from it delay or pause between impulses
INTERFACING TO 8051.
To cause the stepper to rotate, we have to send a pulse to each coil in turn. The 8051 does not have
sufficient drive capability on its output to drive each coil, so there are a number of ways to drive a
stepper,
Stepper motors are usually controlled by transistor or driver IC like

ULN2003.
Driving current for each coil is then needed about 60mA at +5V supply. A Darlington transistor array,
ULN2003 is used to increase driving capacity of the 2051 chip. Four 4.7k resistors help the 2051 to
provide more sourcing current from the +5V supply.
Coil A Coil B Coil C Coil D Step
0 1 1 0 1
0 0 1 1 2
1 0 0 1 3
1 1 0 0 4
CODE EXAMPLE
To move motor in forward direction continuously
Connection -P1.0 -P1.3 connected to Coils A -D.

ASSEMBLY LANGUAGE C LANGUAGE (SPJ)
mov a,#66h ;Load step sequence

void main ()
{
AGAIN
TMOD = 0x20 ;
mov p2,a ;issue sequence to motor
TCON = 0x40 ;
rr a ;rotate step sequence right
TH1 = 0xf9 ;
clockwise=Next sequence
TL1 = 0xf9 ;
acall DELAY ;~ 20 msec.
PCON = 0x80 ;
sjmp AGAIN ;Repete again
SCON = 0x50 ;
while (1) /*continues loop */
{
printf("a"); /* transmit a along with CR
& LF.
}
CONTROLLING STEPPER MOTOR WITH TWO PORT PINS ONLY

For Forward
D0 D0 Coil energized
0 0 AB
0 1 BC
1 0 CD
1 1 DA
To reverse the motor just reverse the above sequence viz. 11,10,01,00.

Stepper Motor

Uploaded by

Stepper Motor

Uploaded by

Stepper Motor

BASICS OF STEPPER MOTOR

In Figure 3.3, as in Figure 3.1, boxes are

The relation between RPM and steps per sec. is given by ,

Stepper motors are usually controlled by transistor or driver IC like

Coil A Coil B Coil C Coil D Step

To move motor in forward direction continuously

Connection -P1.0 -P1.3 connected to Coils A -D.

mov a,#66h ;Load step sequence

CONTROLLING STEPPER MOTOR WITH TWO PORT PINS ONLY

You might also like