Building Coldframes PDF

Cold Frames
P R O J E C T
{This portable cold frame can be built in a day but should last forever. For
best results, paint or stain the wood. See the plan on the next page.
Cold frames
A terrific way to extend the gardening season is with a cold frame. These can be used
to warm the soil, grow plants as in a minigreenhouse or to protect plants like a giant
cloche. Theyre also good for holding flats
of seedlings youve started or plants that
arrived too early to set out.
You can construct a cold frame thats
nearly as warm as a greenhouse. By locating it near the wall of a heated building,
insulating its walls, sinking the foundation
in the soil and using a double-glazed top,
cool-season vegetables could grow in your
cold frame all winter in mild areas. Adding
heating coils or using manure to warm the
soil turns the frame into a hot bed and extends its winter usefulness into colder areas.
You can get as elaborate as you want
with your cold frame. For example, you
can use automatic,
t h e r-
mostat-controlled vent windows and heating units. In this case, the frame almost acts
like a miniature greenhouse.
However, such a permanent frame is not
as flexible as some gardeners would like.
You may prefer a lightweight, portable
frame, which you can take into the garden
and use as a combination soil warmer and
giant cloche.
To use it as such, place the cold frame in
the garden seven to 10 days before you wish
to plant, letting the frame warm the soil.
Then, with it in place, plant your crop directly into the frame. Remove the frame
when weather stabilizes.
Portable frames are available from several sources. Or you can put together a few
low-tech versions. For example, you can
stack bricks or bales of straw in a square
and cover them with glass.
You can make a box and cover it with
an old storm window for a lid. You can
attach plastic window-well covers to a
hinged frame (see photo). Or make the
Garden Gate cold frame shown above.
Two window-well covers can be nailed to a hinged 2 x 4 in.

frame to make a simple and inexpensive cold frame.
plans
N O W
page 1
If you decide to use a cold frame, here

are some tips to get the most from it:
Orient the frame so it runs east to west.
More sun will reach growing plants.
Make the frame lower on the south
side so it catches more sun.
Paint the inside wood of the cold
frame white to help reflect sunlight to
the plants.
Vent the cold frame to keep
it from getting too hot. Venting
also reduces dampness, which
helps keep foliar diseases at bay.
The highest youll want to let
the temperature get is 80 degrees.
But dont let the temperature
drop too low either. The soil under the cold frame needs to absorb enough heat to keep plants
warm at night. An automatic opener will
help tremendously, especially if you work
and cant be there to open and close the lid.
Keep an eye out for air leaks where
warm air can seep out.
Irrigate with water thats at least as
warm as the soil. Cold water will cool the
soil and reduce the effectiveness of the cold
frame. And it can chill the seedlings.
Finally, a tip from a reader for those
extra-cold nights: Place small votive candles
inside the frame, using one candle for every 2 square ft. of space. The candles burn
for hours, protecting plants until morning.
But be careful. Place the candles away
from leaves that might be hanging over the
pot and from any combustible materials in
the cold frame, such as straw, sawdust or
the walls of the frame or your house.
Marilyn Rogers
Sources
Gardeners Supply Co., 128 Intervale Rd.,
Burlington, VT 05401-2804. 800-444-6417.
Row covers, cloches.
Harris Seeds, P.O. Box 22960, Rochester, NY
14692-2960. 800-514-4441. Cold frames,
cloches, plastic, row covers.
Ken-Bar Inc., P.O. Box 504, Reading, MA
01867. 800-336-8882. A list of distributors
for T-518 row covers.
A.M. Leonard, Inc., P.O. Box 816, Piqua, OH
45356. 800-543-8955. Cold frame, plastic.
Walt Nicke Co., P.O. Box 433, Topsfield, MA
01983. 508-887-3388. Cold frames.
1998, August Home Publishing Co.
Just the facts
Acrylic glazing
Exploded view
Cost: $100
Time: to 1 day
Tools: Drill, Skilsaw,
carpenters square, screwdriver
#6 x in.
zinc-coated
Rh screw
Corner
braces
Rail
Hinges
39 3/8 in.
Style
LID
28 in.
36 in.
34 3/8 in.
#6 x in.
zinc-coated
Rh screw
23 in.
BACK
SIDE
L-hook
FRONT
#8 x 1 in.
zinc-coated
Fh screw
61 in.
37 in.
11 in.
Building Tips
Building a cold frame need not be complicated. As you can see, this one is pretty
straight-forward. Still, it offers a large area for growing, its portable, and if you use pressure-treated lumber and galvanized hardware, it should last a lifetime.
We used Plexiglas because it was durable and lightweight. However, the panels cost about $20 each. You
could staple thick plastic over the frame or even use
an old window.
The hooks on front are for two 36 in. perforated
metal straps. These attach to the screws on the front
of the lid to hold it open (see photo, previous page).
plans
N O W
Brick
Materials list
Lumber/Plywood (use treated CCA) Hardware
Front
Back
Sides
Lids
2 x 6 x 61 in.
(2)
2 x 6 x 61 in.
(4)
in. x 2 ft. x 4 ft.
plywood cut to shape
2 x 2 x cut to fit (4)
2 x 2 x 39 in.
(4)
2 x 2 x 28 in.
(4)
page 2
Misc.
Acrylic glazing, 32 x 44 in.

#6 x in. roundhead (Rh) screws*
#8 x 1 in. flathead (Fh) screws*
T-hinges, 5 in. with screws
Corner braces, 3 in. with screws
L-hooks
Perforated strap
(2)
(4)
(8)
(2)
(2)
Bricks
Paint
(32)
* Indicates zinc-coated
1998, August Home Publishing Co.

Building Coldframes PDF

Uploaded by

Building Coldframes PDF

Uploaded by

Cold Frames

Two window-well covers can be nailed to a hinged 2 x 4 in.

If you decide to use a cold frame, here

1998, August Home Publishing Co.

Just the facts

Acrylic glazing, 32 x 44 in.

1998, August Home Publishing Co.

You might also like