a Nexans company

Medium voltage separable

connectors and bushings
- Interface E - 5/8" -

Catalogue 2015

Nexans Network Solutions

Div. Euromold
COMPANY PRESENTATION

EUROMOLD

International standards

Euromold is the leading

European specialised designer,
manufacturer and distributor
of prefabricated cable
accessories for medium voltage
energy distribution. Euromold
provides a complete range of
accessories for underground
cables: premoulded EPDM
rubber connectors for cables
and epoxy bushings for
transformers and switchgear, as
well as a large range of coldshrinkable terminations and
joints from 12 to 42 kV.
Euromold is also the
manufacturer of electrical
components for the high
voltage accessories of the
Nexans group.

All our products meet the

International standards like
CENELEC HD 629.1, CENELEC
EN 50180, IEC 60137, IEC
60502-4 or country specifications. Official certificates,
CESI, KEMA, ATEX prove the
conformity of our products.
Long duration tests of existing
or new products are
continuously performed in our
test fields.

ISO 9001 Certificate

05/2015

Since 1992, Euromolds

commitment to quality is
demonstrated by its ISO 9001
certification.

Laboratory accreditation
Since June 2000, Euromolds
independent ELAB laboratory
obtained the BELAC
accreditation no.144-TEST
conform with the European
standards for laboratories ISO
17025 for electrical testing of
low and medium voltage cable
accessories according to the
international standards HD 623
and HD 629.

While every care is taken to ensure that the information contained

in this publication is correct, no legal responsibility can be accepted
for any inaccuracy. Nexans Network Solutions N.V. - Div. Euromold
reserves the right to alter or modify the characteristics of its products
described in this catalogue as standards and technology evolve.

SEPARABLE CONNECTORS
AND BUSHINGS
INTERFACE E - 5/8"

Table of contents

INTERFACE E - 5/8"

784TB - tee connector

750S1, 775S1 & 775T1 - equipment bushing
Accessories
Possible arrangements

Dimensions according to IEEE

std. 386 (in mm, except where
noted).

Dia. 61.50.2
Dia. 39.90.2
Dia. 32
nominal

1.5 -0.5

5/8"-11UNC-2B

25.4
min

31.750.4

103.70.2

Dia. 76.20.2

05/2015

14.8
min

Connecting possibilities

BUSHINGS /
ACCESSORIES

CONNECTION

CONNECTORS /
ACCESSORIES

dead-ending

Equipment
interface

of equipment

750BE or 775BE
Bushing extender

750S1 or 775S1

Equipment bushing

750BE or 775BE
Bushing extender

750DP or 775DP
Dead-end plug

750CP or 775CP
Connecting plug

connector standing
away from equipment

one cable to

775T1

equipment

Equipment bushing

in-line junction

750CP or 775CP
Connecting plug

dead-ending

750BIP or 775BIP

of connector

784TB

Tee connector

Basic insulating plug

cable isolation

750SOP

Stand-off plug

cable earthing

750GP

05/2015

Earthing plug

784TB

INTERFACE E - 5/8" - TEE CONNECTOR

FOR USE WITH BUSHINGS WITH ALUMINIUM CONTACT ROD

Application
Separable tee shape
connector (bolted type)
designed to connect polymeric
insulated cable to equipment
(transformers, switchgear,
motors, ...).
Also connects cable to cable
when using the appropriate
mating parts.

Up to 42 kV
Up to 800 A

Technical characteristics
The thick conductive EPDM
jacket provides a total safe to
touch screen which ensures
safety for personnel.
Each separable connector is
tested for AC withstand and
partial discharge prior to
leaving the factory.

6/10 (12) kV
6.35/11 (12) kV
8.7/15 (17.5) kV
12/20 (24) kV
12.7/22 (24) kV
18/30 (36) kV
19/33 (36) kV
20.8/36 (42) kV

Design

205 mm

Separable connector
comprising:
1. Conductive EPDM insert.
2. Conductive EPDM jacket.
3. Insulating EPDM layer
moulded between the insert
and the jacket.
4. Type E 5/8" interface as
described by IEEE 386.
5. Conductor contact.
6. Basic insulating plug 858
BIPA (with VD point).
7. Cable reducer.
8. Conductive rubber cap.
9. Stud/nut/washer 5/8".
10. Earthing lead.

9
8

1
2
360 mm

The screen break design

enables cable outer sheath
testing without removing or
dismantling the connector.

10

Specifications and
standards

The 784TB separable connector

meets the requirements of
CENELEC HD 629.1.

784TB/G
K784TB/G
M784TB/G
P784TB/G

Current Ir
(A)

Voltage
Um
(kV)

When installed on an
appropriate equipment bushing

min

max

12
24
36
42

800
800
800
800

50
35
35
35

630
630
630
630

Conductor sizes (mm2)

05/2015

Separable
connector
type

Kit contents
The complete (K)(M)(P)784TB/G
tee connector kit comprises 3x
the following components:

The kit also comprises silicone grease, field

control mastic, gloves, roll adhesive tape,
installation instructions, venting rod and
crimp chart.

Conductor
contact TMBC-X

For use with

copper tape
screened cables.

Order: Kit MT.

For use in potentially

explosive atmospheres
(for 12 kV max.).

Order: -/ATEX.

Dia. over core insulation (mm)

Ordering
part number
3 x 784TB/G-S-15-X
3 x 784TB/G-S-19-X
3 x 784TB/G-S-22-X
3 x 784TB/G-S-27-X
3 x 784TB/G-S-32-X
3 x 784TB/G-S-37-X
3 x 784TB/G-S-43-X

min

max

16.0
20.0
23.5
28.5
34.0
39.0
45.5

22.0
26.5
31.0
37.5
42.5
48.5
56.0

Table X
Aluminium conductor
DIN
hexagonal
35(K)M-10-2

35KM-10-1

50

50(K)M-10-2

50(K)M-10-1

70

70(K)M-10-2

70(K)M-10-1

95

95(K)M-10-2

95(K)M-10-1

120

120(K)M-10-2

120(K)M-10-1

150

150(K)M-10-2

150(K)M-10-1

185

185(K)M-10-2

185(K)M-10-1

240

240(K)M-10-2

240(K)M-10-1

300

300(K)M-10-2

300(K)M-10-1

400

400(K)M-10-2

400(K)M-10-1

500

500(K)M-10-2

500(K)M-10-1

630

630(K)M-10-2

630(K)M-10-1

Please contact our

representative.

Copper
conductor

Bolted

DIN
hexagonal

Deep
indent

35

For use with

other cable types.

Aluminium and
copper conductor

For applications
outdoors and in
humid climate.

Order: +MWS.

35(K)M-14
50(K)M-14
70(K)M-14
95(K)M-14

Components can be
ordered individually.

120(K)M-14
150(K)M-14
185.400-14-5

Conductor sizes
(mm2)

185(K)M-14
240(K)M-14
300(K)M-14
400.630-14-5

Example:
The copper wire screened cable
is 36 kV, 240 mm2 stranded
aluminium with a diameter over
core insulation of 37.0 mm.
Order 3 x
M784TB/G-S-32-240(K)M-10-2.

Table W

95.240-14-5

To order the tee connector,

select the ordering part number which gives you the best
centring of your core insulation
diameter and substitute X
using table X, according to your
conductor size and type.
Add a 'K' for use up to 24 kV,
add an 'M' for use up to 36 kV,
add a 'P' for use up to 42 kV.

Cable reducer
611CA-W

120.300-14-5

Ordering instructions

Conductor
contact TBC-X

50.150-14-5

Stud+nut 5/8"
+washer

Basic insulating
plug
(K)(M)(P)858BIPA
+ rubber cap

16.95-14-5

Connector housing
(K)(M)(P)784BT/G

3 x (K)(M)(P)784TB/GS-W-X
connector kit

400(K)M-14
500(K)M-14
630(K)M-14

Multiple cable
arrangement possible.

Please contact our

representative.

784TB

INTERFACE E - 5/8" - TEE CONNECTOR

FOR USE WITH BUSHINGS WITH COPPER CONTACT ROD

Application
Separable tee shape
connector (bolted type)
designed to connect polymeric
insulated cable to equipment
(transformers, switchgear,
motors, ...).
Also connects cable to cable
when using the appropriate
mating parts.

Up to 42 kV
Up to 1250 A

Technical characteristics
The thick conductive EPDM
jacket provides a total safe to
touch screen which ensures
safety for personnel.
Each separable connector is
tested for AC withstand and
partial discharge prior to
leaving the factory.

6/10 (12) kV
6.35/11 (12) kV
8.7/15 (17.5) kV
12/20 (24) kV
12.7/22 (24) kV
18/30 (36) kV
19/33 (36) kV
20.8/36 (42) kV

Design

205 mm

Separable connector
comprising:
1. Conductive EPDM insert.
2. Conductive EPDM jacket.
3. Insulating EPDM layer
moulded between the insert
and the jacket.
4. Type E 5/8" interface as
described by IEEE 386.
5. Conductor contact.
6. Basic insulating plug 858
BIPA (with VD point).
7. Cable reducer.
8. Conductive rubber cap.
9. Stud/nut/washer 5/8".
10. Earthing lead.

9
8

1
2
360 mm

The screen break design

enables cable outer sheath
testing without removing or
dismantling the connector.

10

Specifications and
standards

The 784TB separable connector

meets the requirements of
CENELEC HD 629.1.

784TB/G
K784TB/G
M784TB/G
P784TB/G

Current Ir
(A)

Voltage
Um
(kV)

When installed on an
appropriate equipment bushing

min

max

12
24
36
42

1250
1250
1250
1250

50
35
35
35

630
630
630
630

Conductor sizes (mm2)

05/2015

Separable
connector
type

Kit contents
The complete (K)(M)(P)784TB/G
tee connector kit comprises 3x
the following components:

The kit also comprises silicone grease, field

control mastic, gloves, roll adhesive tape,
installation instructions, venting rod and
crimp chart.

Conductor
contact TMBC-X

For use with

copper tape
screened cables.

Order: Kit MT.

For use in potentially

explosive atmospheres
(for 12 kV max.).

Order: -/ATEX.

Dia. over core insulation (mm)

Ordering
part number
3 x 784TB/G-S-15-X
3 x 784TB/G-S-19-X
3 x 784TB/G-S-22-X
3 x 784TB/G-S-27-X
3 x 784TB/G-S-32-X
3 x 784TB/G-S-37-X
3 x 784TB/G-S-43-X

min

max

16.0
20.0
23.5
28.5
34.0
39.0
45.5

22.0
26.5
31.0
37.5
42.5
48.5
56.0

Table X
Aluminium conductor
DIN
hexagonal
35(K)M-12-2

35KM-12-1

50

50(K)M-12-2

50(K)M-12-1

70

70(K)M-12-2

70(K)M-12-1

95

95(K)M-12-2

95(K)M-12-1

120

120(K)M-12-2

120(K)M-12-1

150

150(K)M-12-2

150(K)M-12-1

185

185(K)M-12-2

185(K)M-12-1

240

240(K)M-12-2

240(K)M-12-1

300

300(K)M-12-2

300(K)M-12-1

400

400(K)M-12-2

400(K)M-12-1

500

500(K)M-12-2

500(K)M-12-1

630

630(K)M-12-1

Please contact our

representative.

Copper
conductor

Bolted

DIN
hexagonal

Deep
indent

35

For use with

other cable types.

Aluminium and
copper conductor

For applications
outdoors and in
humid climate.

Order: +MWS.

35(K)M-11-2
50(K)M-11-2
70(K)M-11-2
95(K)M-11-2

Components can be
ordered individually.

120(K)M-11-2
150(K)M-11-2
185.400-14-5

Conductor sizes
(mm2)

185(K)M-11-2
240(K)M-11-2
300(K)M-11-2
400.630-14-5

Example:
The copper wire screened cable
is 36 kV, 240 mm2 stranded
aluminium with a diameter over
core insulation of 37.0 mm.
Order 3 x
M784TB/G-S-32-240(K)M-12-2.

Table W

95.240-14-5

To order the tee connector,

select the ordering part number which gives you the best
centring of your core insulation
diameter and substitute X
using table X, according to your
conductor size and type.
Add a 'K' for use up to 24 kV,
add an 'M' for use up to 36 kV,
add a 'P' for use up to 42 kV.

Cable reducer
611CA-W

120.300-14-5

Ordering instructions

Conductor
contact TBC-X

50.150-14-5

Stud+nut 5/8"
+washer

Basic insulating
plug
(K)(M)(P)858BIPA
+ rubber cap

16.95-14-5

Connector housing
(K)(M)(P)784BT/G

3 x (K)(M)(P)784TB/GS-W-X
connector kit

400(K)M-11-2
500(K)M-11-2
630(K)M-11-2

Multiple cable
arrangement possible.

Please contact our

representative.

750S1, 775S1 & 775T1

INTERFACE E - 5/8"
EQUIPMENT BUSHING

Application

Technical characteristics

For use in equipment insulated

with oil fluid, typically for
transformers, switchgear,
capacitors...

Each bushing is tested for

AC withstand and partial
discharge prior to leaving
the factory.

Up to 36 kV
800 A & 1250 A

6/10 (12) kV
6.35/11 (12) kV
8.7/15 (17.5) kV
12/20 (24) kV
12.7/22 (24) kV
18/30 (36) kV

Design
The equipment bushing is a
moulded epoxy insulated part in
accordance with ANSI/IEEE 386
std. (5/8" threading system).

5/8-11UNC-2B
stainless
steel flange

1.5

Specifications and
standards
The bolted type equipment
bushings 750S1, 775S1 and
775T1 meet the requirements
of IEC 60137.

A
Dia.
32

Minimum
oil level:
75 mm

Ordering instructions
To order the equipment
bushing, specify the type.

32
5/8-11UNC-2A
Dia. 76
Dia. 114

In mm, except where noted.

Equipment
bushing
type

Voltage
Ur
(kV)

Current
Ir
(A)

750S1
775S1
775T1

36
36
36

800
1250
1250

75
75
221

235
235
378

05/2015

Dimensions (mm)

FIXINGS FOR
EQUIPMENT BUSHINGS
750S1, 775S1 and 775T1
bushings

bushing interface
fixing studs and
nuts M10
10

fixing flange
type : MK 600-1
(antimagnetic)

equipment
sealing gasket

equipment
connection

140
60

60
170

Bushing fixing flange

To order the bushing fixing
flange, simply specify MK600-1.

In mm.

ACCESSORIES
INTERFACE E - 5/8"

Application

Technical characteristics

For use with connectors and

bushings with an INTERFACE
E - 5/8" as described in IEEE
std. 386.

All these products, except the

earthing plug, are tested for
AC withstand and partial
discharge prior to leaving
the factory.

750CP & 775CP

Connecting plug
For connecting two or more
connectors with a type E - 5/8"
interface together, thus creating
a separable cable joint or a
multiple cable connection to
equipment.

750BE & 775BE

Bushing extender
Provides an extension piece
to allow cables to stand away
from equipment.
Is used in conjunction with the
connecting plug (750CP or
775CP).

750SOP
Stand-off plug

6/10 (12) kV
6.35/11 (12) kV
8.7/15 (17.5) kV
12/20 (24) kV
12.7/22 (24) kV
18/30 (36) kV
Ordering instructions
Order
750CP for 800 A or
775CP for 1250 A
applications.

Ordering instructions
Order
750BE for 800 A or
775BE for 1250 A
applications.

Ordering instructions
Order
750SOP for 800 A and 1250 A
applications.

05/2015

Is designed to support and

'dead-end' connectors with a
type E - 5/8" interface when
removed from equipment.

Up to 36 kV

10

750GP
Earthing plug
Is designed to support and
earth connectors with a type
E - 5/8" interface when
removed from equipment.

Kit MT
Earthing kit for copper
tape screened cables
Contains a tinned copper braid
(25 mm - L = 500 mm), a
tinned copper wire for cleating
and water sealing mastic.

Ordering instructions
Order
750GP for 800 A and 1250 A
applications.

Ordering instructions
Order
Kit MT for 800 A and 1250 A
applications.

11

POSSIBLE ARRANGEMENTS

INTERFACE E - 5/8"

784TB

784TB+850PB

Single cable arrangement.

Order 784TB for 12 kV, 24 kV
or 36 kV applications.

Dual cable arrangement.

Order 784TB+850PB
for 12 kV, 24 kV or 36 kV
applications.
300

195

858BIPA basic
insulating plug

858BIPA
basic insulating plug

850PB coupling
connector
784TB tee connector

784TB tee connector

125

125

105

750BE+784TB

784TB+850SA

Connector standing away from

equipment.
Order 750BE+784TB
for 12 kV, 24 kV or 36 kV
applications.

Dead-ending.
Order 784TB+850SA
for 12 kV, 24 kV or 36 kV
applications.

300

475

750BE
bushing
extender

connecting
plug
750CP or
775CP
784TB tee connector

125

12

In mm.

05/2015

405

Connector on stand-off
plug

stand-off
plug

Connector on earthing
plug

earthing
plug

In mm.

13

05/2015

NOTES

14

15

16

05/2015

Additional catalogue information on power cable accessories

is available by contacting us at the address below:

Distributed by:

Nexans Network Solutions N.V. - Div. Euromold

Zuid III, Industrielaan 12, B-9320 Erembodegem
Tel.: +32 (0)53 85 02 11 sales.euromold@nexans.com www.euromold.be
Catalogue also available on CD-ROM, Website and Mobile Apps

05/2015

a Nexans company