7800 SERIES

RM7800E,G,L,M Relay Module

SPECIFICATION DATA

APPLICATION First-out annunciation and system diagnostics

provided by 2 row by 20 column Vacuum Fluorescent
Display (VFD) located on the Keyboard Display
The Honeywell RM7800 is a microprocessor based integrated Module.
burner control for automatically fired gas, oil or combination
fuel single burner applications. The RM7800 system consists First-out expanded annunciation with 26 Light Emitting
of a Relay Module and Keyboard Display Module, Subbase, Diodes (LEDs) for limits and interlocks (optional).
Amplifier, and Purge Card. Options include Personal Five sequence information LEDs, see Fig. 1.
Computer Interface, DATA CONTROLBUS MODULE,
Remote Display Mounting, First-Out Expanded Annunciator Five function Run/Test Switch.
and Combustion System Manager Software. Interchangeable plug-in flame amplifiers.

The RM7800 is programmed to provide a level of safety, Local or remote annunciation of operation and fault
functional capability and features beyond the capacity of information (optional).
conventional controls. Nonvolatile memory for retaining history files and
sequencing status after loss of power.
Functions provided by the RM7800 include automatic burner
sequencing, flame supervision, system status indication, Remote reset (optional).
system or self-diagnostics and troubleshooting. Report generation (optional).
Burner controller data:
FEATURES Sequence status.
Sequence time.
Safety features: Hold status.
Lockout/alarm status.
Interlock check. Flame signal strength.
Closed loop logic test. Expanded annunciator status.
Dynamic AMPLI-CHECK. Total cycles of operation.
Dynamic input check. Total hours of operation.
Dynamic safety relay test. Fault history of six most recent faults:
Dynamic self-check logic. Cycles of operation at time of fault.
Expanded safe-start check. Expanded annunciator data at time of fault.
High Fire Purge Switch test. Fault message and code.
Internal hardware status monitoring. Hours of operation at time of fault.
Low Fire Start Switch test. Sequence status at time of fault.
Tamper resistant timing and logic. Sequence time at time of fault.
Access for external electrical voltage checks. Diagnostic information:
Application flexibility. Device type.
Flame amplifier type.
Provides 0.8 to 3.0 second Flame Failure Response Flame failure response time.
Time (FFRT), depending on amplifier selected. Manufacturing code.
Communication interface capability. On/Off status of all digital inputs and outputs.
Selected prepurge time.
Dependable, long-term operation provided by Software revision and version of RM7800 and
microcomputer technology. Keyboard Display Module.
Status of configuration jumpers.
Status of Run/Test Switch.

U.S. Registered Trademark

Copyright 2000 Honeywell All Rights Reserved 66- 2028-3
7800 SERIES RM7800E,G,L,M RELAY MODULE

FIVE WIRE CONNECTOR FOR

SPECIFICATIONS
COMMUNICATIONS, REMOTE DI = DIAGNOSTICS
H1 = HISTORY
KEYBOARD DISPLAY AND REMOTE RESET
EA = EXPANDED
Electrical Ratings, see Table 1:
RUN/TEST SWITCH ANNUNCIATOR Voltage and Frequency: 120 Vac (+10/-15%),
50 or 60 Hz (+/- 10%)4.
CAPTIVE Keyboard Display Module: 13 Vdc peak full wave rectified
SEQUENCE MOUNTING
STATUS SCREW (+20/-15%).
SELECTABLE PLUG-IN
Power Dissipation:
MESSAGE OR PURGE RM7800: 10 Watts maximum.
PRE-EMPTIVE CARD Display Module: 3 Watts maximum.
MESSAGE
KEYBOARD Maximum Total Connected Load: 2000 VA.
DISPLAY Fusing: Total Connected Load: 20A maximum, type FRN
SEQUENCE MODULE
STATUS
or equivalent.
LEDs RELAY
MODULE Environmental Ratings:
Ambient Temperature:
RESET FLAME
PUSHBUTTON AMPLIFIER
Operating: -40F to 140F (-40C to 60C).
FLAME
Storage: -40F to 150F (-40C to 66C).
FLAME CURRENT Humidity: 85% RH continuous, noncondensing.
SIMULATOR INPUT
TEST JACKS M7359
Vibration: 0.5G environment.
Fig. 1. Keyboard Display Module Weight:
and sequence status LEDs.
RM7800: 1 pound 13 ounces, unpacked.
Keyboard Display Module: 4 ounces, unpacked.

Dimensions: See Fig. 2.

Approval Bodies:
Underwriters Laboratories Inc. listed, File No. MP268,
Guide No. MCCZ.
Canadian Standards Association certified, LR9S329-3.
Factory Mutual approved, Report No. J.I.1V9A0.AF.
IRI acceptable.
Federal Communications Commission, Part 15,
Class BEmissions.

Mounting: Q7800A for panel mount or Q7800B for wall

or burner mount.

Required Components:
Plug-in Flame Signal Amplifier, see Table 2.
ST7800A Plug-in Purge Timer Cards: selectable models:
two seconds to 30 minutes.
Q7800A or Q7800B Wiring Subbase.

66-20283 2
 7800 SERIES RM7800E,G,L,M RELAY MODULE

Table 1. Terminal Ratings.

Terminal No. Description Ratings
G a
Flame Sensor Ground
Earth G Earth Grounda
L2(N) Line Voltage Common
3 Alarm 120 Vac, 1A pilot duty.
4 Line Voltage Supply (L1) 120 Vac (10/-15%), 50 or 60 Hz (10%)b,d
5 Burner Motor 120 Vac, 9.8 AFL, 58.8 ALR (inrush).
6 Burner Controller and Limits 120 Vac, 1 mA.
7 Lockout/Running Interlock 120 Vac, 8A run, 43A inrush.
8 Pilot Valve/Ignition 120 Vacc
9 Main Fuel Valve 120 Vacc
10 Ignition 120 Vacc
F(11) Flame Sensor 60 to 220 Vac, current limited.
12 Firing Rate High Fire 120 Vac, 75 VA pilot duty.
13 Firing Rate Common 120 Vac, 75 VA pilot duty.
14 Firing Rate Low Fire 120 Vac, 75 VA pilot duty.
15 Firing Rate Modulate 120 Vac, 75 VA pilot duty.
16 Unused
17 Unused
18 Low Fire Switch Input 120 Vac, 1 mA.
19 High Fire Switch Input 120 Vac, 1 mA.
20 Preignition Interlock Input 120 Vac, 1 mA.
21 Interrupted/Intermittent Pilot Valve/First Stage Oil 120 Vacc
Valve.
22 Shutter 120 Vac, 0.5A.
a
The RM7800 must have an earth ground providing a connection between the subbase and the control panel or the equipment.
The earth ground wire must be capable of conducting the current to blow the 20A fuse (or breaker) in the event of an internal
short circuit. The RM7800 needs a low impedance ground connection to the equipment frame which, in turn, needs a low
impedance connection to earth ground.
b
2000 VA maximum connected load to RM7800 Assembly.
c
See Tables 3 and 4.
d
R7800G,M operating frequency determined by relay module selection.

3 66-20283
7800 SERIES RM7800E,G,L,M RELAY MODULE

Table 2. Sequence timing for normal operation.

Flame Establishing
Period Post Firing Energy Approval
Purge Interlock Rate Saving Code
Device Initiate Standby Purge Pilot Maina Run Timing Circuits Circuit Prepurge Bodies
RM7800E 10 sec. * ** 4 or 10 10 or 15 * 15 sec. Preignition, 4-wire Yes FM/IRI
sec. sec. Lockout, modulating Modulatin.
High and .
Low Fire.
RM7800G 10, 15 sec. Preignition, No UL/CSA
or Running, Modulating
intermittent Low Fire
RM7800L 10 or 15 Preignition, FM/IRI
sec.b Lockout, Modulating
High and
Low Fire.
RM7800M 10 sec. or Preignition, 2-wire UL/CSA
intermittent Running, isolated On/Off.
Low Fire. On-Off-On
contacts
*
STANDBY and RUN can be an infinite time period.
**
PURGE will be determined by which ST7800A purge card is selected; 15 timings are available, from 2 seconds to 30 minutes.
a
The MFEP will be determined by which terminal is used, configuration jumper selected, or jumper wire added.
b
RM7800L1056: 10 seconds or intermittent.

Table 3. Combinations for terminals 8, 9, 10 and 21.

Pilot Fuel Main Ignition Intermittent Pilot Valve
Combination No. 8 9 10 21
1 C F No Load No Load
2 B
3 No Load B
4 F A No Load
5 No Load F
6 D No Load
7 No Load D D
8 D No Load
9 No Load D

Table 4. Composition of each combination.

A B C D F
4.5A Ignition. 50 VA Pilot Duty plus 180 VA Ignition plus 2A Pilot Duty. 64 VA PIlot Duty plus
4.5A Ignition. Motor valve with: Motor valves with:
660 VA inrush, 3850 VA inrush,
360 VA open, 700 VA open,
250 VA hold. 250 VA hold.

66-20283 4
 7800 SERIES RM7800E,G,L,M RELAY MODULE

BURNER CONTROL

5
(127)

POWER
PILOT
FLAME
MAIN
ALARM 1

RESET

5-1/4 (133)
5 (127)

1 REMOVE ONLY FOR

TERMINAL TEST ACCESS.

6-3/32 (155)

M15518

Fig. 2. Mounting dimensions of RM7800 Relay Module, Q7800 Subbase, and Q7800 Subbase, respectively, in in. (mm).

Accessories: S7810A1009 Data ControlBus Module (if no KDM is

Keyboard Display Modules (KDM): used).
S7800A1001 English language (Standard) S7810B1007 Data ControlBus Module, Multi-Drop
S7800A1035 French language. Switch Module.
S7800A1043 German language. S7810M1003 ModBus Module.
S7800A1050 Italian language. Miscellaneous:
S7800A1068 Spanish language. A7800A1002 7800 SERIES Tester.
S7800A1118 Katakana (Japanese) language. S7820A1007 Remote Reset Module.
S7800A1126 Portuguese language. S7830A1005 Expanded Annunciator, 120 Vac, 50/60 Hz.
S7800B1009 Chinese language. 203541 Data ControlBus Connector, 5-wire.
Communications: 203765 Remote Display Mounting Bracket.
Q7700A1014 Network Interface Unit, 120 Vac, 50/60 Hz 221729 Dust Cover, Relay Module.
applications, external modem required. 204718A Keyboard Display Module Cover, NEMA 4, clear.
Q7700B1004 Network Interface Unit with universal 204718B Keyboard Display Module Cover, NEMA 1, clear.
100 to 250 Vac, 50/60 Hz external power supply, 204718C Keyboard Display Module Cover, NEMA 4, clear
external modem required. with reset button.
QS7800A1001 ControlBus Module, standard. 205321B Flush Display mounting kit.
QS7800B1000 ControlBus Module, multidrop. 221818A Extension Cable, display, 5 ft (1524 mm).
QS7850A1006 ControlBus Module, General Purpose 221818C Extension Cable, display, 10 ft (3048 mm).
Interface. 123514A Rectification Flame Simulator.
ZM7850A1001 Combustion System Manager software. 203659 Ultraviolet Flame Simulator.
203968A Remote Display Power Supply, 13 Vdc, plug-in.

5 66-20283
7800 SERIES RM7800E,G,L,M RELAY MODULE

Table 5. Flame Detector System.

Plug-In Flame Signal Amplifiers Applicable Flame Detectors
Flame Failure
Type Color Self-Checking Model Response Time Fuel Type Models
Rectification Green No R7847A 0.8 or 3 sec. Gas Rectifying Flame C7004, C7007, C7011.
Rod Holdersa Complete Assemblies:
C7008, C7009, Q179.
Oil Rectifying C7003, C7010, C7013,
Photocell C7014.
3 sec. Gas, oil, Ultraviolet (Purple C7012A,Cb
coal Peeper)
Dynamic R7847BC 0.8 or 3 sec. Gas Rectifying Flame C7004, C7007, C7011.
AMPLI-CHECK Rod Holdersa Complete Assemblies:
C7008, C7009, Q179.
Oil Rectifying C7003, C7010, C7013,
Photocelld C7014.
3 sec. Gas, oil, Ultraviolet (Purple C7012A,Cb
coal Peeper)
Dynamic R7847Ce,f Ultraviolet (Purple C7102E,F.
Self-Check Peeper)
Infrared Red No R7848A Infrared (Lead C7015.
Dynamic c Sulfide)
R7848B
AMPLI-CHECK
Ultraviolet Purple No R7849A 0.8 or 3 sec. Gas, oil Ultraviolet C7027, C7035, C7044b.
(Minipeeper)
Dynamic R7849Bc
AMPLI-CHECK
Dynamic R7861Ae Ultraviolet C7061.
Self-Check
Blue Dynamic R7886Ae 3 sec. Gas, oil, Ultraviolet C7076.
Self-Check coal (Adjustable
Sensitivity)
Optical White Dynamic R7851B 0.8 or 3 sec. Gas, oil, Optical C7927, C7935, C7915,
AMPLI-CHECK coal (Ultraviolet, C7962.
infrared, visible
light)
a
Order flame rod separately, see holder instructions.
b
The C7012A,C; C7027, C7035 and C7044 Flame Detectors should be used only on burners that cycle on-off at least once
every twenty-four hours. Appliances with burners that remain on continuously for twenty-four hours or longer should use the
C7012E,F Flame Detector with the R7847C Amplifier; the C7061A Flame Detector with the R7861 Amplifier, or the C7076A,D
Flame Detector with the R7886A Amplifier as the ultraviolet flame detection system.
c
Circuitry tests the flame signal amplifier at least 12 times a minute during burner operation and shuts down the boiler if the
amplifier fails.
d
Use only Honeywell Photocell, part number 38316.
e
Circuitry tests all electronic components in the flame detection system (amplifier and detector) 12 times a minute during burner
operation and shuts down the burner if the detection system fails.
f
Series 4 and greater check flame detector system when flame reaches 1.5 Vdc or at 4.5 seconds whichever occurs first.

66-20283 6
7 66-20283
Home and Building Control Home and Building Control Honeywell Asia Pacific Inc. Honeywell Europe S.A. Honeywell Latin American
Honeywell Honeywell Limited-Honeywell Limite Room 3213-3225 3 Avenue du Bourget Region
1985 Douglas Drive North 35 Dynamic Drive Sun Hung Kai Centre 1140 Brussels 480 Sawgrass Corporate Parkway
Golden Valley, MN 55422 Scarborough, Ontario No. 30 Harbour Road Belgium Suite 200
M1V 4Z9 Wanchai Sunrise FL 33325
Hong Kong

Printed in U.S.A. on recycled

66-20283 G.R. Rev. 12-00 paper containing at least 10% www.honeywell.com
post-consumer paper fibers.