Scribd
Upload
159 views

Introduction To Reactors

A reactor is a coil with many turns that has a high resistance value. Reactors are used to limit short circuit currents that can damage power system equipment by adding reactance to the system. Current limiting reactors specifically limit heavy current flows through parts of the system, allowing isolation of faulty sections without shutting down the whole system. Reactors also protect circuit breakers by limiting currents according to breaker capacities. This allows utilization of the same breakers through added reactors instead of replacement, saving time and money.

Uploaded by

hailekah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
159 views

Introduction To Reactors

A reactor is a coil with many turns that has a high resistance value. Reactors are used to limit short circuit currents that can damage power system equipment by adding reactance to the system. Current limiting reactors specifically limit heavy current flows through parts of the system, allowing isolation of faulty sections without shutting down the whole system. Reactors also protect circuit breakers by limiting currents according to breaker capacities. This allows utilization of the same breakers through added reactors instead of replacement, saving time and money.

Uploaded by

hailekah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Introduction to reactors

A reactor is a coil which has large number of turns and


whose ohmic resistance value is much greater.
Reactors are used to limit the short circuit currents
which can cause damage to the equipments of the
power system. The additional reactance added in
series with the system for protection, are called
reactors.

A current limiting reactor is a type of reactor which


limits the heavy flow of current through other sections
of the system. In this way, we dont have to shut down
the whole system, we can just isolate the faulty
section.

Reactors are also used to protect the circuit breakers


of different ratings. They are used to limit the short
circuit currents according to the capacity of circuit
breakers. Therefore while doing changes in the
system, we dont have to replace the circuit breakers,
instead we can add reactors and utilize the same
circuit breaker, due to which, time and money, both
can be saved.

Working principle of current limiting reactors:


If the reactance of a circuit during fault is X, and E
voltages are given, then the short circuit current can
be calculated as:
Isc= E/X

i.e, the reactance is inversely proportional to the


current. If X increases, Isc decreases and vice versa.
Short circuit currents depend on the generating
capacity, fault point voltage and the reactance of the
circuit. The figure illustrates the use of a current
limiting reactor:

reactors
The rating of reactors is given in KVA and the formula
for percentage reactance is:

%X= KV drop/ KV(phase voltage)


Some other uses of reactors:
1. For arc suppression.
2. To filter out harmonics.
3. In series with low reactance auto transformers.
4. In series with low reactance induction regulators.
5. To protect from high voltage waves, surges and
lightning.
6. To control starting currents of motors.
TYPES OF REACTORS:
On the basis of construction, the reactors are of two
types:

1. Dry type or Air core or Open type or Unshielded


type reactors.
2. Oil immersed or magnetically shielded or iron core
reactors.
1. Air core reactors:
The reactors in which no iron core or steel core is used
are called air core reactors. These reactors are only
used up to 33kv.

These reactors are larger in size. Concrete slabs are


arranged in the form of a circle and stranded copper
coil conductors are embedded in it. These slabs
provide good mechanical strength during short circuit
currents.

Post insulators made of porcelain support these


reactors. These are also called cast concrete type
reactors. Insulated conductors are used for winding. To
provide insulation between turns, glass or porcelain
material is used.

Advantages:
These are simple, have constant current and
reactance and have greater mechanical strength.
Disadvantages:
Not suitable for outdoor services, take much space
due to their large size, difficult to provide cooling and
can only be used up to 33kv.

1. Iron core reactors:


The reactors consisting of iron core are called iron
core reactors. A coil is placed inside a standard
transformer tank and oil is filled for cooling and
insulation purposes. Shielding is provided to prevent
losses. And to prevent stray magnetic fields, the core
is laminated. Shields are made in the form of short
circuited rings and are earthed through end plates.
The mmf produced in the rings, due to short-circuit
current, keeps the flux inside the shield.

These reactors are also called oil immersed type


reactors and can be used for any voltage level.

Advantages:
These reactors provide greater protection against
short-circuit currents, have high thermal capacity,
suitable for both indoor and outdoor services and can
be operated at any voltage level.

Disadvantages:
They are costly, complex and difficult to repair.
Location of
Reactors in power
system
Reactors in the power system can be located

1. In series with generators


2. In series with feeders or
3. In bus-bars (in ring system or in tie-bar system).
These arrangements are known as

1. generator reactors,
2. feeder reactors,
3. bus-bar reactors (ring system) and bus-bar reactors
(tie-bar system) respectively.

(a) Generator Reactors (b) Feeder Reactors

Generator reactors protect the generators individually and this system of connecting
reactors is adopted only when an old power station is to be operated in a parallel with the
new incoming machines. In case of feeder reactor arrangement, in the event of fault on
any one feeder the voltage drop in its reactor and bus-bar voltage is not affected much and
so other machines continue supplying load.

Disadvantage of locating
reactors
The disadvantage of locating reactors in this position is that:

1. These do not protect the generators when short circuit occurs across the bus-bars
but ties is of no impotence because such faults are rare and modern alternators have
large transient reactance for their protection against short circuits.
2. The other disadvantage is of constant voltage drop and constant power loss in the
reactor even during normal operation. This draw-back can be overcome by inserting
the reactors in the bus-bars either
(c) Bus-bar Reactors (Ring-system) (b) Bus-bar Reactors (Tie-bar System)

You might also like