Value Stream

Mapping +
Simulation
Taking Your Map to the
Next Level

www.flexsim.com
 Value Stream Mapping + Simulation

Table
of Contents
2 WHAT IS VALUE STREAM MAPPING?

3 DOES IT HAVE LIMITATIONS?

The Bottleneck Problem
The Dependency Problem
The Variability Problem

5 OVERCOMING THE LIMITATIONS

Solving the Bottleneck Problem
Solving the Dependency Problem
Solving the Variability Problem

8 CASE STUDY
How Advanced Process Optimization, Inc. used simulation
modeling in concert with traditional Lean techniques to deliver
an advanced process improvement solution

www.flexsim.com 1
 Value Stream Mapping + Simulation

What Is
Value Stream Mapping?
Value stream mapping is a visual flowcharting tool used frequently in Lean
manufacturing to diagram the information and material flow in a system. This tool
makes it possible to identify constraints, value-added time, and non-value added
timeall with the intention of recognizing possible system improvements. Its often
done before an improvement project to determine the current state, followed by a
future-state proposal using an altered version of the map to determine the benefits
of the proposed changes.

Value stream mapping uses standard symbols that represent different aspects of a
system and help to visually describe the system to others. Standard calculations are
available to assess the performance of various parts of the system. These standard
symbols and calculations make it easy to determine which parts of the system
should be the focus of improvement efforts.

www.flexsim.com 2
 Value Stream Mapping + Simulation

Does it
Have Limitations?
Value stream mapping is an effective tool when it comes to visually representing
simple material flow systems. However, as the system exhibits more complex
behavior, the map becomes less capable of representing the reality that is
occurring.

THE BOTTLENECK PROBLEM

takt time: the average unit
Lets imagine a system is mapped out where the production time needed to
customer demand results in a takt time less than meet customer demand
the cycle time of one or more of the processes. In
cycle time: the total time from
this case, the utilization of that process step (cycle
the beginning to the end of a
time divided by takt time) would be calculated as process
above 100 percent. In reality, that process cant
have a utilization above 100 percent, so the system bottleneck: a congested
process that causes the entire
is unable to meet the customer demand. The system to slow down or stop
result is a queue that continuously builds before
the bottlenecked step. In a value stream map,
the size of the inventory before the process is just
a snapshot of an ever-increasing queue; the total
non-value added time is only accurate for that
specific time frame. This becomes a problem when
a future state map is drafted and changes are
made based on irrelevant data and the predicted
results of the project are not met.

www.flexsim.com 3
 Value Stream Mapping + Simulation

THE DEPENDENCY PROBLEM

Value stream mapping has a tendency to treat each individual process as an

independent step in the system, but systems have complex interdependencies that
are often glossed over while creating a map. An example involves the previously
mentioned utilization calculation of cycle time divided by takt time. If an upstream
process is highly utilized, it would affect the availability of work that can be done on
downstream products decreasing the utilization of all downstream processes.

THE VARIABILITY PROBLEM

One of the most dangerous assumptions of value stream mapping is the use of
a static cycle time. In most systems these processing times are not exact, and
mapping them using exact numbers ignores the difficulties created by variability.
Lean manufacturing is focused on reducing the waste in a system; much of that
waste is from queueing steps before process steps. These queueing steps are
usually added to the system to separate the variability that is exposed between
processes. By failing to model the variance in processing times, value stream
mapping ignores this important intricacy of the system.

www.flexsim.com 4
 Value Stream Mapping + Simulation

Overcoming
the Limitations
The limitations of value stream mapping are rooted in the fact that a value stream
map is just a snapshot of the current system. Evaluating processes as they are
currently observed fails to predict how things will change in the immediate future.
This is a problem, since all changes will be executed in a future state of the system.

Thankfully, all is not lost. If value stream mapping is combined with simulation,
then one can predict not only how changes will affect the current system, but also
how those changes will affect the system as it exists in the future. Simulation is
also effective at modeling the interdependencies that are present in almost every
system, because it reproduces how objects would actually have to flow through the
system. And simulation is useful for solving the variability problem, because it can
model the variance in process times as it imitates product movement through the
system.

www.flexsim.com 5
 Value Stream Mapping + Simulation

WHAT IS SIMULATION?
Simulation modeling is the process of creating and evaluating a virtual
prototype of a real-world system. The virtual environment provides a safe place
where data is easy to come by and where mistakes result in improvement
instead of ending careers. When its presented in an intuitive and easy-to-use
software package, simulation is a powerful problem-solving tool that allows
decision makers to answer important what if questions about their business.

1. SOLVING THE BOTTLENECK PROBLEM

By modeling the movement of products through a system, its possible to identify

the bottlenecks quickly. Bottlenecks are obvious during simulation because of
the ability to actually watch inventories build up queues before the congested
processes. This continual growth, shown only in a simulation, is evidence that the
proceeding step is not capable of meeting customer demand. The utilization of this
step is also correctly calculated at somewhat less than 100 percent, which would be
much closer to the actual utilization of the observed process.

2. SOLVING THE DEPENDENCY PROBLEM

As the simulation moves products through the system, the actions of one part of
the system are dependent on the other parts. Simulation does not allow a product
to be processed unless there are actually products available to be processed. This
makes it possible to accurately depict the value added vs. non-value added time of
the system, and also more adequately represents the utilization rate of each of the
processes.

www.flexsim.com 6
 Value Stream Mapping + Simulation

3. SOLVING THE VARIABILITY PROBLEM

Simulation is probably most suited to solving the variability problems associated

with static value stream mapping analysis. The use of randomly determined
representations of process times makes it possible to accurately reflect the variance
that is represented in the system. Any proposed changes to reduce waste can be
made with more confidence. And since many inventory buffers are in the system
to separate the variability between process steps, modeling that variance can show
how implementing supermarkets or pull strategies will actually affect the dynamic
system and not just the static system represented in a traditional value stream
map.

www.flexsim.com 7
 Value Stream Mapping + Simulation

Case Study
How Advanced Process Optimization, Inc. used simulation modeling in concert with
traditional Lean techniques to deliver an advanced process improvement solution

The Client: A rail bearing manufacturer, and an industry leader in friction

reduction and drive systems.
The Task: Evaluate the process performance of a rail system bearing
reconditioning and assembly facilitywith the goal of identifying opportunities to
improve throughput.

INTRODUCTION
What would be a typical Lean manufacturing approach to this sort of process
analysis? The solution might involve time studies and value stream mapping
(VSM). These techniques provide valuable insights and a direction to launch Kaizen
initiatives focused on improving performance. A well-made VSM will take a high-
level look at the average cycle times, changeover times, and inventory levels for
a processall powered by information gathered on a Gemba Walk audit by your
friendly process improvement specialist. Identify the waste, overburden, and
fluctuationsMuda, Muri, and Muraso you can start to eliminate and control
them.

These are all good things. But what these techniques dont provide is the depth of
analysis found in simulation modeling. Youll gain the ability to model variation over
long time horizons, truly exposing the inefficiencies in a system. And by having a
stochastic (random) representation of the data, the variance found in the real world
is better represented. Multiple (and longer) simulation runs will show a time-varying
range of effects on constraints, inventory, and key metrics.

In this improvement project, Advanced Process Optimization, Inc. (APO) married

traditional Lean Six Sigma (LSS) techniques with simulation modeling using FlexSim.
Their experience showed how simulation modeling can reinforce LSS by adding

www.flexsim.com 8
 Value Stream Mapping + Simulation

powerful analytical capabilities, eye-opening visualization, and new ideas plus

ownership while vetting.

1. CURRENT-STATE MODEL TRUST AND ANALYSIS

APO used FlexSim to create a current-state model of the facility centered on the
project scope: four original equipment lines and three reconditioning inspection/
assembly lines. The model was populated with data taken from an onsite time
study, and driven by a years worth of production data. From this starting point,
APO leveraged the Lean principles of single piece flow, supermarkets, Kanban,
water spider replenishment and more to conceptualize a future state of the system.

This current-state simulation model served two purposes. It provided built-in

reporting and analysis tools that APO used to better understand what is happening
during simulation runs of the current-state model. But even more importantly, it
established trust. The model was proven to accurately emulate the system, a crucial
requirement that sets the stage for all future experimentation with the facility in a
virtual space.

www.flexsim.com 9
 Value Stream Mapping + Simulation

2. FUTURE-STATE MODEL VISUALIZATION

The future-state model took full advantage of FlexSims realistic and native 3D
capabilities. APO used an AutoCAD drawing as the plants footprint and populated it
with 3D FlexSim objects to represent the human and machine resources used in the
facility. This allowed the model to be both a realistic and properly scaled portrayal
of the future state concept.

This mock-upor paper doll exercise, as it is sometimes referred to in Lean

allowed APO to visualize the new workspace and flow of materials through the
system. They could then check the projected performance against the current-state
model they had developed earlier.

3. DESIGN VETTING IDEAS AND OWNERSHIP

Once the future-state model was ready, the client team assembled to vet the
design. APO actually wanted the team to tear their design apartlooking for
weaknesses, flaws, errors, and missed opportunities to uncover better designs.

The beauty of a simulation model is that we have an immersive

environment to virtually experience the workspace while
conducting what-if scenarios on the system.

Jason Merschat
President and CEO
Advanced Process Optimization, Inc.

The vetting process is an invaluable opportunity for a future-state design to be

improved. The design capabilities of the system are pushed by the addition of
variation to test robustness, conflicts, hidden dependencies, constraints, and
bottleneck influences. The same goes for staffing levels, replenishment, flow

www.flexsim.com 10
 Value Stream Mapping + Simulation

rate, and anything else seen as important to the process. Each time, the model is
modified and improved.

With FlexSim, this entire process is easy. It requires no physical resources or

manpower to test the system, only ideas and a few button clicks. And when the
client team gets to actively participate in changing values and variablesbuilding a
better future-state piece-by-piecethey begin to take ownership of the model and
its results.

RESULTS AND CONCLUSION

The future-state model predicted a one-year
cost savings of $607K due to eliminating
non-value added processes, waste, and
laborwhile also seeing a throughput
increase of 52% and a labor productivity
increase of 108%! The client is in the process
of implementing this new design at their first
location, and APO will go to two additional
locations to model those systems as well.
APO will now switch gears from analysis and
design to focus on implementation, helping
the client get ramped up and integrate some PROJECTED
of the more challenging lean tools. IMPROVEMENTS
52% Throughput increase
APO found that this hybrid traditional Lean 108% Labor productivity
and simulation technique took full advantage increase
of the unique benefits of simulation: $607K one-year cost savings!
minimizing risk, evaluating scenarios,
and optimizing based on constraints. It
also opened new ideas and opportunities throughout the vetting process. Lean
techniques and tools remain the foundation for their process improvement
approach, but simulation modeling is the next evolution in visualizing, analyzing,
and designing a process.

www.flexsim.com 11
FlexSim Software Products, Inc.
1577 North Technology Way
Orem, UT 84097
(801) 224-6914
sales@flexsim.com
www.flexsim.com