Scribd
Upload
85 views

Event Code List

dw

Uploaded by

Putra Jawa
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
85 views

Event Code List

dw

Uploaded by

Putra Jawa
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

CROSS-REFERENCE LIST OF PTNR TO SCM, CBSA, DECATUR & MOSSVIL 6KG...

Page 1 of 3

Shutdown SIS

Previous Screen

Product: EXCAVATOR
Model: E200B EXCAVATOR 6KG
Configuration: CROSS-REFERENCE LIST OF PTNR TO SCM, CBSA, DECATUR & MOSSVIL 6KG00001-UP (MACHINE)

Troubleshooting
Product Link - PL522/523
Media Number -RENR8143-01 Publication Date -01/08/2011 Date Updated -23/08/2011

i03993410

Event Code List


SMCS - 7569

Event codes alert the operator or the technician that an abnormal operating condition exists in one of
the machine systems.

When an Electronic Control Module (ECM) activates an event code, the operator or the technician
will be alerted by the Messenger. Most active events will be logged by the ECM. Some events are
active only. Active only events are not logged. The events that are active and the events that are
logged can be viewed with the following equipment:

Messenger

Caterpillar Electronic Technician (Cat ET)

Warning Levels
The ECM will assign a warning level to an active event code. Event codes are one of three levels. The
level represents the severity of the abnormal condition. Each warning level requires a specific
response from the operator. The warning levels and the required operator response are listed below.

Warning Level 1
Warning level 1 alerts the operator that a machine system requires attention. The operator should
check the system condition or perform maintenance on the involved system at the earliest possible
time.

Warning Level 2
Warning level 2 requires changing the operation of the machine or performing a maintenance
procedure. Failure to correct the problem that caused this warning may damage the components that
are involved in the system.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/f... 9/6/2017
CROSS-REFERENCE LIST OF PTNR TO SCM, CBSA, DECATUR & MOSSVIL 6KG... Page 2 of 3

Warning Level 3
Warning level 3 requires an immediate safe shutdown of the machine in order to avoid damage to the
machine or injury to personnel. The problem that caused the event must be corrected before machine
operation can resume.

Indications and System Response


Caterpillar Electronic Technician (Cat ET) Service Tool
When an abnormal operating condition occurs, the status screen on the Cat ET indicates that there is
an active event.

Event codes are displayed on Cat ET in the following format:

EXXXX Description of the code

The "E" means that the code is an event code. The "XXXX" is a numeric identifier. The numeric
identifier is followed by a description of the code.

Active event codes are listed in ascending numerical order. The code with the lowest number is listed
first. The active event code is removed from the list when the condition is no longer present.

Logged Event Codes

Some event codes are logged in the ECM memory. Some event codes are active only. The logged
event codes are listed in chronological order. The most recent code is listed first.

A logged code is cleared from memory when one of the following conditions occur:

The service technician manually clears the code.

The code does not reoccur after a number of hours determined by each ECM.

A new code is logged and there are already ten logged codes in memory. In this case, the oldest
logged code is cleared.

Note: Always clear logged event codes after investigating and correcting the problem which
generated the code.

List of Event Codes


The following table lists event codes and the recommended responses. Use the Cat ET service tool in
order to determine the event codes that are active or logged.

Table 1
List of Event Codes (EID)

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/f... 9/6/2017
CROSS-REFERENCE LIST OF PTNR TO SCM, CBSA, DECATUR & MOSSVIL 6KG... Page 3 of 3

EID Level
Description Possible Cause and Recommended Response

In a PL522 or 523 system using sync-clock and Product Link


that is not the master ECM, the Product Link module will
Synchronized
automatically sync to the master ECM hours if the difference is
861 clock notification
1 not greater than 50 hours. If the difference is greater than 50
of manual synch
hours, a diagnostic will be generated in Cat ET that indicates
required
that a manual sync is required. In that instance, sync the hours.
In Cat ET, use "Service/Synchronize Service Meter Hours".
The PL522 or 523 has four additional inputs that can be
Switched Sensor configured in order to monitor switches on the machine. These
630
2 #1 trip condition inputs can be configured by using Caterpillar Electronic
is activated Technician (Cat ET service tool). Troubleshoot input as setup
by the dealer.
The PL522 or 523 has four additional inputs that can be
Switched Sensor configured in order to monitor switches on the machine. These
631
2 #2 trip condition inputs can be configured by using Caterpillar Electronic
is activated Technician (Cat ET service tool). Troubleshoot input as setup
by the dealer.
The PL522 or 523 has four additional inputs that can be
Switched Sensor configured in order to monitor switches on the machine. These
632
2 #3 trip condition inputs can be configured by using Caterpillar Electronic
is activated Technician (Cat ET service tool). Troubleshoot input as setup
by the dealer.
The PL522 or 523 has four additional inputs that can be
Switched Sensor configured in order to monitor switches on the machine. These
633
2 #4 trip condition inputs can be configured by using Caterpillar Electronic
is activated Technician (Cat ET service tool). Troubleshoot input as setup
by the dealer.

Copyright 1993 - 2017 Caterpillar Inc. Wed Sep 6 07:26:08 UTC+0700 2017
All Rights Reserved.
Private Network For SIS Licensees.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/f... 9/6/2017

You might also like