EoC Telnet - Command Line

No new Wires.... www.wodaplug.
com
Catalogue- Comand Lined description

2.Homeplug EoC AV74 command......................................................................................................7
2.1 show......................................................................................................................................7
2.1.1. show cbat_info..........................................................................................................7
2.1.2. show cbat_topo_info.................................................................................................8
2.1.3. show cbat_perf..........................................................................................................9
2.1.4 show cbat_vlan_list....................................................................................................9
2.1.5 show cbat_vlan_info (vlanid)....................................................................................9
2.1.6 show card_info.........................................................................................................10
2.1.7 show card_topo_info................................................................................................10
2.1.8 show card_rf_info....................................................................................................11
2.1.9 show card_qos..........................................................................................................12
2.1.10 show analog_info...................................................................................................12
2.1.11 show cnu_info........................................................................................................13
2.1.12 show cnu_qos.........................................................................................................15
2.1.13 show cnu_rt_stats...................................................................................................16
2.1.14 show default_cnu_config.......................................................................................16
2.1.15 show mgmt_vlan....................................................................................................18
2.1.16 show pre_cnu_list..................................................................................................18
2.1.17 show pre_cnu_config.............................................................................................19
2.1.18 show trap_server....................................................................................................20
2.1.19 show whitelist_info................................................................................................21
2.1.20 show anonymitylist_info.......................................................................................22
2.2. set.......................................................................................................................................22
2.2.1 set analog_alarm......................................................................................................22
2.2.2 set cbat_pvid (portid) (pvid)....................................................................................23
2.2.3 set cbat_dot1q_vlan_mode (mode)..........................................................................23
2.2.4set card_igmp_snooping...........................................................................................23
2.2.3 set card_isolation.....................................................................................................24
2.2.4 set card_qos_dscp....................................................................................................24
2.2.5 set card_qos_queue_threshold.................................................................................25
2.2.6 set card_qos_queue_ttl.............................................................................................25
2.2.7 set card_qos_service_pri..........................................................................................25
2.2.8 set card_qos_threshold.............................................................................................26
2.2.9 set card_qos_tos.......................................................................................................26
2.2.10 set card_qos_tos_mapping.....................................................................................27
2.2.11 set card_qos_vlan...................................................................................................27
2.2.12 set card_qos_vlan_mapping...................................................................................27
2.2.13 set cbat_bstorm_ctrl...............................................................................................28
2.2.14 set cbat_bstorm_rate..............................................................................................28
2.2.15 set cnu_bstorm_ctrl................................................................................................29
2.2.16 set cnu_rt_stats_reset.............................................................................................29
2.2.17 set cnu_cable_speedlimit.......................................................................................29
1
No new Wires.... www.wodaplug.com
2.2.18 set cnu_igmpsp_ctrl...............................................................................................30

2.2.19 set cnu_isolation....................................................................................................30
2.2.20 set cnu_maclimit....................................................................................................30
2.2.21 set cnu_mstorm_ctrl...............................................................................................31
2.2.22 set cnu_port_linkpolicy..........................................................................................31
2.2.23 set cnu_port_pri.....................................................................................................32
2.2.24 set cnu_port_pvid...................................................................................................32
2.2.25 set cnu_port_status.................................................................................................33
2.2.26 set cnu_port_speedlimit.........................................................................................33
2.2.27 set cnu_qos_dscp...................................................................................................33
2.2.28 set cnu_qos_vlan....................................................................................................34
2.2.29 set cnu_qos_queue_threshold................................................................................34
2.2.30 set cnu_qos_queue_ttl............................................................................................34
2.2.31 set cnu_qos_service_pri.........................................................................................35
2.2.32 set cnu_qos_threshold............................................................................................35
2.2.33 set cnu_qos_tos......................................................................................................36
2.2.34 set cnu_qos_tos_mapping......................................................................................36
2.2.35 set cnu_qos_vlan_mapping....................................................................................37
2.2.36 set cnu_stormctrl_pps............................................................................................37
2.2.37 set cnu_vlanmode..................................................................................................37
2.2.38 set cnu_unkstorm_ctrl............................................................................................38
2.2.39 set dns_server.........................................................................................................38
2.2.40 set ipaddr................................................................................................................39
2.2.41 set ntp_server.........................................................................................................39
2.2.42 set mgmt_vlan........................................................................................................40
2.2.43 set trap_server........................................................................................................40
2.2.44 set upgrade_server.................................................................................................41
2.2.45 set default_cnu_igmpsp_ctrl..................................................................................41
2.2.46 set default_cnu_bstorm_ctrl...................................................................................41
2.2.47 set default_cnu_mstorm_ctrl.................................................................................42
2.2.48 set default_cnu_unkstorm_ctrl...............................................................................42
2.2.49 set default_cnu_stormctrl_pps...............................................................................42
2.2.50 set default_cnu_cable_speedlimit..........................................................................43
2.2.51 set default_cnu_port_speedlimit............................................................................43
2.2.52 set default_cnu_vlanmode.....................................................................................43
2.2.53 set default_cnu_maclimit.......................................................................................44
2.2.54 set default_cnu_port_linkpolicy............................................................................44
2.2.55 set default_cnu_port_pri........................................................................................44
2.2.56 set default_cnu_port_status...................................................................................45
2.2.57 set default_port_pvid.............................................................................................45
2.2.58 set cnu_loopdetect_mode.......................................................................................45
2.3. add......................................................................................................................................46
2.3.1 add whitelist.............................................................................................................46
2.4. del.......................................................................................................................................46
2
2.4.1 del cnu......................................................................................................................46

2.4.2 del white...................................................................................................................47
2.5. reset...................................................................................................................................47
2.5.1 reset card..................................................................................................................47
2.5.2 reset cbat..................................................................................................................48
2.5.3 reset cnu...................................................................................................................48
2.6 restore..................................................................................................................................48
2.6.1 restore cbat_factory_default...................................................................................48
2.6.2 restore cnu_factory_default.....................................................................................49
2.7. upgrade...............................................................................................................................49
2.7.1 upgrade app..............................................................................................................49
2.7.2 upgrade kernel..........................................................................................................50
3.Cablengine MEoC command of users managment....................................................................50
3.1 keepalive.............................................................................................................................50
3.2. logout..................................................................................................................................50
3.3. who.....................................................................................................................................51
Cablengine MEoC Configuration Environment
1.1 Configuration Environment
Fig.1.1 WEB management configuration environment
Confirm the connection between Master and Slave, then use Switch connect with
Master, uplink to Computer, show as fig.1.1.
1.2 Steps of Configuration Environment
Setp 1As shown fig.1-1,Connect PC ,Master by switch .

Masters default network conig.IP:192.168.0.254subnet
mask:255.255.255.0default gateway:192.168.0.1DNS is 61.177.7.1NTP server
is time.nist.gov
Step 2[StartRuncmdtelnet Master IP Address 23enter user ID and
password( rootpublic)
Step 3enter commandConfigure equipment or check the equipment running status, Please got
the help from(TAB) if it is necessary
3
1.3 Note
1, the MEoC management for for common computer or server;

2, system memory requirements above 128 m;
3, Operating system support Windows 2000, Windows XP, Linux, Mac OS X operating system
2.Cable Speed M240NR Command description
2.1 show
2.1.1. show cbat_info
Command function
Check the system information
command format
show cbat_info
user guide
Datetime; the present time of master
Starttime;the starting time of master
ConfigurationThe network info.of master is automatically or static configuration
Software Versionindicate the software Version No.
Hardware Versionindicate the hardware version
StartFreq; Start Frequency
StopFreq;End Frequency
Workmode;OFDM/CMTS
Upgrade Server Indicate the IP address when upgrade by FTP or TFTP server
Upgrade Server Port ; Update server port number
Telnet timeout
Bstorm Mode; Broadcast Limit
Bstorm Rate; The broadcast storm inhibition rate,
Dns Server;Dns servers IP,default is Dns management ip.
Ntp Server netOnly can set IP address,default is time.nist.gov
Flow Control ;the status of flow,default is enable
Dot1q Vlan ModeMasters vlan enable
For example
MEOC>>show cbat_info
Date Time : 1970-01-02 18:59:30
Start Time : 1970-01-01 00:00:27
4
Cpu Mac : 00:55:ff:01:00:01

Tech Project : HomePlugAV
Model Number : M240NR
Configuration : Static Ip Address
Software Version : 5.b.0.8
Hardware Version : M2400NR-REV1.0
Ip Address : 192.168.1.67
Netmask : 255.255.255.0
Gateway : 192.168.1.1
Start Freq : 7.5 MHz
Stop Freq : 67.5 MHz
Work Mode : OFDM
Upgrade Server : 192.168.0.122
Upgrade Server Port : 21
Dns Server : 192.168.0.1
Ntp Server : time.nist.gov
Max CnuCount : 64
Max CnuOnline : 64
Scan Mode : Disable
Flow Control : Enable
BStorm Mode : Disable
BStorm Rate : 1 per mill of port link rate
Dot1q Vlan Mode : Disable
------------------------------------
Cbat Port Info
Port 1:
Status : Deactive
Pvid :1
Port 2 (Management Port):
Status : Active
LinkPolicy : 100M Full Duplex
Pvid :1
2.1.2. show cbat_topo_info
For example
MEOC>>show cbat_topo_info
Cpu Mac : 00:55:ff:01:00:01
Card Count : 1
Id Mac Address Status

-----------------------------------------
0 00:55:ff:00:00:05 Reg Ok
5
related command

2.1.3. show cbat_perf
command function

command format
show cbat_perf
parameter description
Cpu Load cpu

Memory Usage
For example
MEOC>>show cbat_perf
Cpu Load : 20%
Memory Usage : 50%
related command

2.1.4 show cbat_vlan_list
For example
MEOC>>show cbat_vlan_list
VLAN List: 1, 11, 20, 400, 1200,
2.1.5 show cbat_vlan_info (vlanid)
For example
MEOC>>show cbat_vlan_info 11
VLAN: 11
Member Ports: 1, 2,
Untag Member Ports: 1, 2,
6
2.1.6 show cbat_rt_stats
For example
MEOC>>show cbat_rt_stats
Port 1:
Tx Bytes :0
Tx Unicast Packets : 0
Tx Broadcast Packets : 0
Tx Multicast Packets : 0
Rx Bytes :0
Rx Unicast Packets : 0
Rx Broadcast Packets : 0
Rx Multicast Packets : 0
Rx Dropped Packets : 0
Port 2 (Management Port):
Tx Bytes : 360795
Tx Unicast Packets : 1405
Tx Broadcast Packets : 0
Tx Multicast Packets : 0
Rx Bytes : 1734072
Rx Unicast Packets : 1415
Rx Broadcast Packets : 19765
Rx Multicast Packets : 646
Rx Dropped Packets : 0
2.1.7 show card_info
user guide
Firstly need use show cbat_topo_info to check the S/N.No.It is the Id.
For example
MEOC>>show card_info 0
Card Id :0
Card Mac : 00:00:00:00:1a:06
Status : Reg Ok
Online Time : 1970-01-01 00:00:33
FW Version : INT7400-MAC-7-0-7001-14-31-20110706-FINAL-D
Model Number : M240NR
Isolation : Enable
IgmpSp Mode : Enable
Max Cnu : 64
7
Cnu Count :3
Cnu Online Count : 3
Running Time : 0d:0h:5m:48s
2.1.8 show card_topo_info
command function
Indicate card topo information
command format
show card_topo_info(cardid)
parameter Description
Param:Need show cards S/N
For example
MEOC>>show card_topo_info 0
Card Id : 0
Card Mac : 00:55:ff:00:00:05
Cnu Count : 29
Id Mac Address Status Access Authorize Tx Rx

---------------------------------------------------------------
6 00:55:ff:00:00:46 Online Deny Yes 0 0
11 00:55:ff:00:00:4b Online Deny Yes 0 0
26 00:55:ff:00:00:5a Online Deny Yes 0 0
29 00:55:ff:00:00:5d Online Deny Yes 0 0

2.1.9 show card_rf_info
For example
MEOC>>show card_rf_info 0
Card Id :0
Link MaxChannelNum : 2452
Output Level : 105 dBuV
DownStream StartFreq : 7.5 MHz
DownStream StopFreq : 67.5 MHz
UpStream StartFreq : 7.5 MHz
UpStream StopFreq : 67.5 MHz
8
2.1.10 show card_qos
For example
MEoC>>show card_qos 0
card ID: 0
VLAN Qos: enable TOS Qos: disable
Priority VLAN Tags TOS Bits
0 CA1 CA1
1 CA0 CA0
2 CA0 CA0
3 CA1 CA1
4 CA2 CA2
5 CA2 CA2
6 CA3 CA3
7 CA3 CA3
TTL: CA0 CA1 CA2 CA3 MME

2000 2000 300 300 300
Default CAP:
IGMP : CA3
IGMP managed Multicast Stream: CA2
Multicast/Broadcast : CA1
Unicast : CA1
TX Buffer Allocation: Enable
Allocation: CA0 CA1 CA2 CA3

20% 25% 45% 10%
related command
show cnu_qos
2.1.11 show analog_info
For example
MEOC>>show analog_info
AnalogType HIHI HI LO LOLO Deadband
Temperature 80 60 0 0 0
CPU 100 60 0 0 0
Memory 100 60 0 0 0
Velocity 100 60 0 0 0
9
Yawp 100 60 0 0 0
Attenuation 100 60 0 0 0
2.1.12 show cnu_info
command function

command format
show cnu_info (cnuid)
cnuid: cnu
Authorize authorization status

Accessallowdeny
Port Isolation Mode:enable mean opendisable mean close
Loop Detection Modeenabledisable
Loop Status:loopingno loop
Phy Tx cable
Phy Rx cable
Phy Tx Link Quality
Phy Rx Link Quality
Avg Bits/Carrier
Avg SNR/Carrier
Avg Attenuation/Carrier
Avg Pre-FEC Bit Error Rate
For example
MEOC>>show cnu_info 6
Cnu 6
Cnu Mac : 00:55:FF:00:00:46
Card Id :0
Init : Finished
Online Time : 1970-01-01 00:00:43
FW Version : INT6000-MAC-4-1-4102-00-3679-20090724-FINAL-C
Custorm Type : s122prv
Switch Type : Realtek
Port Num : 2
Authorize : Yes
Access : Deny
Status : Online
Isolation : Enable
------------------------------------
Switch Info
10
IgmpSp Mode : Disable

MStorm Mode : Disable
UnkStorm Mode : Disable
Storm Rate : 80 pps
Port Isolation Mode : Disable
Loop Detection Mode : Disable
Loop Status : No Loop
Vlan Mode : Transparent
Cable Up Limit : 100 Mbps
Cable Dn Limit : 100 Mbps
Mac Limit : 0, Disable
------------------------------------
Link Info
Phy Tx : 0 Mbps
Phy Rx : 0 Mbps
Phy Tx Link Quality : 0%
Phy Rx Link Quality : 0%
Avg Bits/Carrier : 0.00
Avg SNR/Carrier : 0.00
Avg Attenuation/Carrier : 0
Avg Pre-FEC Bit Error Rate : 0.00%
------------------------------------
Ethernet Port Info
LAN 1:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
Port Up Limit : 100 Mbps
Port Dn Limit : 100 Mbps
LAN 2:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
2.1.13 show cnu_qos
For example
MEoC>>show cnu_qos 16
11
cnu ID: 16
VLAN Qos: enable TOS Qos: disable
Priority VLAN Tags TOS Bits
0 CA1 CA1
1 CA0 CA0
2 CA0 CA0
3 CA1 CA1
4 CA2 CA2
5 CA2 CA2
6 CA3 CA3
7 CA3 CA3
TTL: CA0 CA1 CA2 CA3 MME

2000 2000 300 300 300
Default CAP:
IGMP : CA3
IGMP managed Multicast Stream: CA2
Unicast : CA1
TX Buffer Allocation: Enable
Allocation: CA0 CA1 CA2 CA3

20% 25% 45% 10%
related command
show card_qos.
2.1.14 show cnu_rt_stats
For example
MEOC>>show cnu_rt_stats 28
Cnu 28
Tx Packets : 258051162
Rx Packets : 12647621
Rx Droped Packets : 0
Rx CRC Error Packets : 0
related command
show card_rt_stats
12
2.1.15 show default_cnu_config
For example
MEOC>>show default_cnu_config
Default Cnu Config:
Access: Deny
------------------------------------
Switch Info
Storm Rate : 80 pps
Vlan Mode : Transparent
------------------------------------
Ethernet Port Info
LAN 1:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
LAN 2:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
LAN 3:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
LAN 4:
LinkPolicy : Auto
13
Pri :0
Status : Active
Pvid :1
------------------------------------
Qos Info
Vlan Qos : Enable
Tos Qos : Disable
Priority Vlan Tags Tos Bits
0 CA1 CA1
1 CA0 CA0
2 CA0 CA0
3 CA1 CA1
4 CA2 CA2
5 CA2 CA2
6 CA3 CA3
7 CA3 CA3
TTL
CA0 CA1 CA2 CA3 MME
2000 2000 300 300 300
Default CAP
Igmp : CA3
Igmp Managed Multicast Stream : CA2
Unicast : CA1
Tx Buffer Allocation : Disable

Allocation
CA0 CA1 CA2 CA3
20 % 25 % 45 % 10 %
2.1.16 show ip_access_list
For example
MEOC>>show ip_access_list
Ip Access Control: Disable
Ip Access List (Total Num: 1):
Ip: 192.168.1.60, Netmask: 255.255.255.255
14
2.1.17 show mgmt_vlan
For example
MEoC>>show mgmt_vlan
Management vlan :
mode:Disable
vlanid:0
2.1.18 show pre_cnu_list
MEOC>>show pre_cnu_list
Id Mac Address
--------------------------------
1 00:55:ff:00:21:03
2 00:55:ff:00:21:06
3 00:55:ff:00:21:05
4 00:55:ff:00:21:08
5 00:55:ff:01:21:05
2.1.19 show pre_cnu_config
For example
MEOC>>show pre_cnu_config 00:55:ff:01:21:05
Pre Cnu Config:
------------------------------------
Switch Info
BStorm Mode : Enable
Storm Rate : 80 pps
Vlan Mode : Access
------------------------------------
15
Ethernet Port Info

LAN 1:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
LAN 2:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
LAN 3:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
LAN 4:
LinkPolicy : Auto
Pri :0
Status : Active
Pvid :1
2.1.20 show trap_server
user guide
Max Times range <1-255>
Min Interval range<1-255>
Max Interva range <1-255>
For example
MEOC>>show trap_server
Ip Address : 192.168.1.55
Max Times : 255
Min Interval : 0
Max Interval : 0
16
Community : public
Status : Enable
related command
set trap_server
2.1.21 show whitelist_info
For example
MEOC>>show whitelist_info
Register WhiteList Number : 3
All RF Output Level : 105 dBuV
Cnu Mac Limit Number : 8
Phy Rate Gate : 200000000 bps
Cnu 8 Info
Card Id :0
Cnu Mac : f4:3e:61:da:19:c8
Cnu Status : Online
Cnu 28 Info
Card Id :0
Cnu Mac : f4:3e:61:da:af:dc
Cnu Status : Online
Cnu 60 Info
Card Id :0
Cnu Mac : f4:3e:61:da:19:bc
Cnu Status : Online
related
add white_mac del white_mac.
2.1.22 show anonymitylist_info
command function
Show MAC black list in the system
17
2.2. set
2.2.1 set analog_alarm
command format
set analog_alarm (analog) (hihi) (hi) (lo) (lolo) (deadband)
parameter specification
Analog items:,
1 Temperature
2 CPU cpu Utilization Rate
3 memory memory Utilization Rate
4 velocity link rate
5 yawp Noise
6 attenuation
hihi : too high
hi : a little high
lo : a little low
lolo : too low
deadband :dead zone value
For example
MEOC>>set analog_alarm 1 70 50 20 10 10
Set Analog Success.
2.2.2set card_igmp_snooping
command formart
set card_igmp_snooping (cardid) (mode)
mode: enable mean open
disable mean close
For example
MEoC>>set card_igmp_snooping 0 enable
Set Card 0 IGMP Snooping Success.
18
2.2.3 set card_isolation
command format
set card_isolation (cardid) (mode)
mode:enable
disable
For example
MEoC>>set card_isolation 0 disable
Set Card 0 Isolation Success.
2.2.4 set card_qos_dscp
command format
set card_qos_dscp (cardid) (mode)
mode:enable
disable
For example
MEoC>>set card_qos_dscp 0 enable
Set Card 0 QoS Dscp enable Success.
related command
show card_qos
2.2.5 set card_qos_queue_threshold
command format
set card_qos_queue_threshold (cardid) (queue) (percent)

queue:CA1CA3
percent:
For example
MEoC>>set card_qos_queue_threshold 0 CA1 40
Set QoS Queue Threshold Success.
related command
19
show card_qos
2.2.6 set card_qos_queue_ttl
command format
set card_qos_queue_ttl(cardid) (queue) (ttl)
queue: CA0~CA3,MME
ttl: 10~65000
Ttl MME range is 3002000
For example
MEoC>> set card_qos_queue_ttl 0 CA2 300
Set Card 0 QoS TTL Success.
related command
show card_qos
2.2.7 set card_qos_service_pri
command format
set card_qos_service_pri (cardid) (type) (queue)
typeunicast
mcast
igmp
avstream IGMP Controlled multicast
For example
MEoC>> set card_qos_service_pri 0 mcast CA1
Set Card 0 QoS Service Priority Success.
related command
show card_qos
2.2.8 set card_qos_threshold

command format
set card_qos_threshold (cardid) (operation)
operation: enable
20
disable
For example
MEoC>> set card_qos_threshold 0 enable
Set Card 0 QoS Threshold Enable Success.
related command
show card_qos
2.2.9 set card_qos_tos

command function
Enable or disable qos and tos function
command format
set card_qos_tos (cardid) (operation)
param: enable
disable
For example
MEoC>> set card_qos_tos 0 enable
Set Card 0 QoS Tos enable Success.
related command
2.2.10 set card_qos_tos_mapping
command format
set card_qos_tos_mapping (cardid) (queue) (tos)
queue: CA0~CA3
tos:0~7
user gudie
CA3 is the highestCA0 is the lowest
For example
MEoC>> set card_qos_tos_mapping 0 CA2 4
Set Card 0 QoS Tos Mapping Success.
related command
2.2.11 set card_qos_vlan
command function
enable or disable qoss vlan function
21
command format
set card_qos_vlan (cardid) (operation)
param: enable
disable
For example
MEoC>> set card_qos_vlan 0 enable
Set Card 0 QoS Vlan enable Success.
related command
show card_qos
2.2.12 set card_qos_vlan_mapping
command function
Set the mapping between qos and vlan
command format
set card_qos_vlan_mapping (cardid) (queue) (vlanid)
queue CA0~CA3:
user guide
CA3 is the highestCA0 is the lowesst
For example
MEoC>> set card_qos_vlan_mapping 0 CA3 3
Set Card 0 QoS Vlan Mapping Success.
related command
show card_qos
2.2.13 set cbat_rt_stats_reset
command function
Remove the card real-time performance information
command format
set cbat_rt_stats_reset
For example
MEOC>>set cbat_rt_stats_reset
Clean Cbat Realtime Statistic Success
22
2.2.14 set cbat_pvid (portid) (pvid)
command function
Set port pvid
command format
set cbat_pvid (portid) (pvid)
Portid cbat port No.,range<1~2> pvid cbats port vid range
is<1~4094>
For example
MEOC>>set cbat_pvid 2 200
related command
2.2.15 set cbat_dot1q_vlan_mode (mode)
command function
enable or disable802.1q vlan
command format
set cbat_dot1q_vlan_mode (mode)
mode(enable|disable)
For example
related command
2.2.16 set cbat_bstorm_ctrl
command function
enable or disable masters broadcast limit function
command format
set cbat_bstorm_ctrl (mode)
modeenabledisable
For example
MEoC>> set cbat_bstorm_ctrl enable
Set Cbat Broadcast Storm Control Enable Success.
23
related command
2.2.17 set cbat_bstorm_rate
command format
cbat_bstorm_rate
For example
MEOC>>set cbat_bstorm_rate 10
related command
2.2.18 set cbat_flow_ctrl
command format
set cbat_flow_ctrl (mode)
Modeenable|disable
Enable
Disable
For example
MEOC>>set cbat_flow_ctrl disable
related command
2.2.19 set cbat_max_cnu_count
For example
MEOC>> Set cbat_max_cnu_count 10
24
2.2.20 set cnu_bstorm_ctrl
For example
MEOC>> set cnu_bstorm_ctrl 16 enable

Set Cnu:16 Broadcast Storm Control Enable Success.
related command
2.2.21 set cnu_rt_stats_reset
command function
Remove the slaves real-time performance information
command format
set cnu_rt_stats_reset (cnuid)
For example
MEOC>>set cnu_rt_stats_reset 28
Clean Cnu :28 Realtime Statistic Success.
2.2.22 set cnu_cable_speedlimit
command function
Set the uplink and downlink bandwidth of cnu
command format
set cnu_cable_speedlimit (cnuid) (uplink) (downlink)
uplink
downlink
For example
MEOC>>set cnu_cable_speedlimit 24 1 16
Set Cnu:24 Speed limited Success.
2.2.23 set cnu_igmpsp_ctrl
command function
enable or disable cnus igmp snooping
25
command format
set cnu_igmpsp_ctrl (cnuid) (mode)
modeenable | disable
For example
MEOC>> set cnu_igmpsp_ctrl 16 enable
Set Cnu:16 IGMP Snooping Control Enable Success.
2.2.24 set cnu_loopdetect_mode
command function
enable or disable
command format
set cnu_loopdetect_mode (cnuid) (mode)
Cnuidcnu id
modeenable|disalbe
For example
MEOC>>set cnu_loopdetect_mode 16 enable
Set Cnu:16 Loop Detection Enable Success.
2.2.25 set cnu_isolation
For example
MEOC>> set cnu_isolation 16 disable

Set Cnu:16 Isolation Success.
2.2.26 set cnu_maclimit
command function
Set cnu max qty of access
command format
set cnu_maclimit (cnuid) (macnum)
26
The qty of macnum is [0,8]
For example
MEOC>> set cnu_maclimit 16 5
Set Cnu:16 Mac Limit Success.
2.2.27 set cnu_mstorm_ctrl
For example
MEOC>>set cnu_mstorm_ctrl 28 enable
Set Cnu:28 Multicast Storm Control Enable Success.
2.2.28 set cnu_port_linkpolicy
command function
Set cn port workmode
command format
set cnu_port_linkpolicy (cnuid) (port) (linkpolicy)
linkpolicyauto
100_full
100_half
10_full
10_half
For example
MEoC>> set cnu_port_linkpolicy 16 1 auto
Set Cnu 16 Port 1 Linkpolicy Success.
2.2.29 set cnu_port_pri
For example
MEoC>> set cnu_port_pri 16 1 4
Set Cnu:16 Port 1 Pri 4 Success.
27
2.2.30 set cnu_port_pvid
For example
MEOC>> set cnu_port_pvid 16 1 5
Set Cnu:16 Port 1 Vlan Success.
related command

2.2.31 set cnu_port_status
For example
MEOC>> set cnu_port_status 16 1 open
Set Cnu:16 Port 1 status open Success.
2.2.32 set cnu_port_speedlimit
command function
Set cnu port speedlimit
command format
set cnu_port_speedlimit (cnuid) (port) (upspeed) (downspeed)
Cnuidcnus ID no.
Portcnu port NO.
Upspeeduplink
Downspeeddownlink
For example
MEOC>>set cnu_port_speedlimit 24 1 5 5
Set Cnu:24 Port 1 Speedlimit Success.
2.2.33 set cnu_port_isolation_mode
For example
MEOC>> set cnu_port_isolation_mode 31 enable
related command
28
2.2.34 set cnu_qos_dscp
For example
MEOC>> set cnu_qos_dscp 16 enable
Set Cnu 16 QoS Dscp Enable Success.
related command

2.2.35 set cnu_qos_vlan
For example
MEOC>> set cnu_qos_vlan 16 enable
Set Cnu 16 QoS Vlan Enable Success.
2.2.36 set cnu_qos_queue_threshold
command function
Set the percent of priority queue in intellon chipcommand format
set cnu_qos_queue_threshold (cnuid) (queue) (percent)
queueCA0CA3
percent:
user guide
CA3 is the highestCA0 is the lowestunable be allowed to be set
For example
MEoC>> set cnu_qos_queue_threshold 16 CA1 25
Set Cnu 16 QoS Queue Threshold Success.
2.2.37 set cnu_qos_queue_ttl
For example
MEoC>> set cnu_qos_queue_ttl 16 CA1 3000
Set Cnu 16 QoS TTL Success.
29
2.2.38 set cnu_qos_service_pri
For example
MEoC>> set cnu_qos_service_pri 16 mcast CA1
Set Cnu 16 QoS Service Priority Success.
2.2.39 set cnu_qos_threshold
For example
MEoC>> set cnu_qos_threshold 16 enable
Set Cnu 16 QoS Threshold Enable Success.
2.2.40 set cnu_qos_tos
command function
enable or disablecnu qos tos
command format
set cnu_qos_tos (cnuid) (operation)
operation:enable disable
For example
MEoC>> set cnu_qos_tos 16 enable
Set Cnu 16 QoS Tos Enable Success.
2.2.41 set cnu_qos_tos_mapping
For example
MEoC>>set cnu_qos_tos_mapping 16 CA1 4
Set Cnu 16 QoS Tos Mapping Success.
2.2.42 set cnu_qos_vlan_mapping
For example
MEoC>> set cnu_qos_vlan_mapping 16 CA2 7
Set Cnu 16 QoS Vlan Mapping Success.
30
2.2.43 set cnu_stormctrl_pps
For example
MEOC>>set cnu_stormctrl_pps 28 10
Set Cnu:28 Bstorm PPS Success.
2.2.44 set cnu_vlanmode
For example
MEoC>> set cnu_vlanmode 16 access
Set cnu:16 Vlan Mode Success.
2.2.45 set cnu_unkstorm_ctrl
For example
MEoC>> set cnu_unkstorm_ctrl 16 enable
Set Cnu:16 Unknown Storm Control Enable Success.
2.2.46 set dns_server
For example
MEOC>>set dns_server 192.43.244.18
Set Ntp Server Success.
2.2.47 set ipaddr
command function
Set systems ip
command format
set ipaddr (ipconfig) (ip) (netmask) (gateway)
ipconfig: static-> IP
dhcp-> IP
31
ip
netmas k
gateway
For example
Static
MEoC>> set ipaddr static 192.168.0.247 255.255.255.0 192.168.0.1
/*******************************caution**************************/
/*If you want to take effect the IP address,please Reset system*/
/****************************************************************/
Dhcp.
MEOC>>set ipaddr dhcp
Set Cbat Ip Success.
/*******************************caution**************************/
/*If you want to take effect the IP address, please Reset Cbat!*/
/****************************************************************/
2.2.48 set ip_access_ctrl
command format
set ip_access_ctrl (enable|disable)
2.2.49 set ntp_server
For example
MEOC>>set ntp_server 192.43.244.18

Set Ntp Server Success.
2.2.50 set mgmt_vlan
For example
MEoC>> set mgmt_vlan disable 8
/*******************************caution**************************/
/****Take effect the management vlan config,Need Reset Cbat****/
/****************************************************************/
32
2.2.51 set trap_server
command function
Set trapservers information
command format
set trap_server (serverip) (maxtimes) (mininterval) (maxinterval) (community) (status)
serveripip
maxtimes: range at <0~255>
mininterval: <0~255>
maxinterval: <0~255>
community.
status:enable|disable
For example
MEOC>> set trap_server 192.168.0.125 200 100 3000 public enable
Set TrapServer Config Success.
related command
Show trap_server
2.2.52 set upgrade_server
command function
ip
command format
set upgrade_server (serverip) (port) (user) (password)
Serverip:p
port
use
password
user guide}
show cbat_info to check whether upgrade sucessfully
For example
MEOC>> set upgrade_server 192.168.0.9 21 root public
Set Upgrade Server Success.
2.2.53 set default_cnu_igmpsp_ctrl
command format
33
set default_cnu_igmpsp_ctrl (mode)

mode : enable
disable
2.2.54 set default_cnu_bstorm_ctrl

command format
set default_cnu_bstorm_ctrl (mode)
mode : enable
disable
For example
2.2.55 set default_cnu_mstorm_ctrl
command format
set default_cnu_mstorm_ctrl (mode)
mode : enable --
disable
2.2.56 set default_cnu_unkstorm_ctrl
command format
set default_cnu_unkstorm_ctrl (mode)
mode : enable
disable
2.2.57 set default_cnu_stormctrl_pps
command format
set default_cnu_stormctrl_pps (number)
34
number : 640,320,160,80,40,20,10
2.2.58 set default_cnu_cable_speedlimit
command format
set default_cnu_cable_speedlimit (upspeed) (downspeed)
2.2.59 set default_cnu_port_speedlimit
command format
set default_cnu_port_speedlimit (port) (upspeed) (downspeed)
2.2.60 set default_cnu_vlanmode
command format
set default_cnu_vlanmode (mode)
mode : transparent ,disable vlan
access enable vlan
2.2.61 set default_cnu_maclimit
command format
set default_cnu_maclimit (number)
2.2.62 set default_cnu_port_linkpolicy
command format
set default_cnu_port_linkpolicy (port) (linkpolicy)
linkpolicy : auto
100_full
100_half
35
10_full
10_half
2.2.63 set default_cnu_port_pri
command format
set default_cnu_port_pri (port) (pri)
pri : 0~7
2.2.64 set default_cnu_port_status
command format
set default_cnu_port_status (port) (status)
status : open
close
2.2.65 set default_cnu_port_pvid
command format
set default_cnu_port_pvid (port) (pvid)
pvid : 1~4094
2.2.66 Set default_cnu_access

command format
Set default_cnu_access (operation)
operation : access|deny
user guide
Accessallow to access
Denyrefuse to access
36
2.3. add
2.3.1 add cbat_vlan (vlanid)
command function
Creat vlan
command format
add cbat_vlan (vlanid)
Vlanid:<1~4094>
2.3.2 add cbat_vlan_member (vlanid) (portid) (mode)
command function
Add vlan member and set the rules
command format
add cbat_vlan_member (vlanid) (portid) (mode)
Vlanid:<1~4094>
Portid:<1~2>
Mode: (tag|untag) tag is pors pvid value untag will be showed in
cbat_vlan_info
For example
MEOC>>add cbat_vlan_member 1 1 untag
related command
MEOC>>show cbat_vlan_info 1
Vlan: 1
Member Ports: 1, 2,
Untag Member Ports: 1, 2,
2.3.3 add ip_access_allow
For example
MEOC>>add ip_access_allow 192.168.1.60 255.255.255.255
Add Ip Access Allow Success.
related command
37
2.3.4 add whitelist
For example
MEOC>>add whitelist 28
Add White Mac Success.
related command
show whitelist_info
2.4. del
2.4.1 del cbat_vlan (vlanid)
command function
Delete vlan
command format
del cbat_vlan (vlanid)
Vlanid<1~4094>
2.4.2 del cbat_vlan_member (vlanid) (portid)
command function
Delete vlan members
command format
del cbat_vlan_member (vlanid) (portid)
Vlanid<1~4094>
Portid<1~2>;
2.4.3 del cnu
command function
Delete slaves
2
1 offlining
38
2 offline
command format
del cnu (cnuid)
For example
MEoC>> del cnu 41
Del Cnu 41 Success.
MEOC>>del cnu 41
ERROR :Cnu Offlining, Try Later
ERROR :Ceserver Return Error!
2.4.4 del ip_access_allow
command format
ip_access_allow (ip) (netmask)
Ipip
Netmask
For example
MEOC>>del ip_access_allow 192.168.0.0 255.255.255.255
Del Ip Access Allow Success.
2.4.5 del white
command function
Delete mac white list
command format
del whitelist (cnuid)
For example
MEOC>>del whitelist 28
Del White Mac Success
related command
show anonymitylist_info
39
2.5. reset
2.5.1 reset card
command function
Reset cards intellon chip
command format
reset card (cardid)
For example
MEoC>> reset card 2
Restart Card Success.
2.5.2 reset cbat
command function
Reset cbat
command format
reset cbat
For example
MEoC>> reset cbat
Reset Cbat Success.
2.5.3 reset cnu
command function
Reset cnus intellon chip
command format
reset cnu (cnuid)
For example
MEoC>> reset cnu 5
Reset Cnu 5 Success
related command

40
2.6 restore
2.6.1 restore cbat_factory_default
For example
MEoC>> restore cbat_factory_default
Restore Cbat Factory Default Configuration Success
2.6.2 restore cnu_factory_default
For example
MEoC>> cnu_factory_default 2
Restore Cnu 2 Config Success.
2.7. upgrade
2.7.1 upgrade app
command format
upgrade app
2.7.2 upgrade kernel
command function
Upgrade masters software-kernel
command format
upgrade kernel (kerne)
3.Cablengine MEoC
3.1 keepalive
For example
MEOC>>keepalive 200
Set Telnet Keepalive Timer Success
41
MEOC>>keepalive
Telnet Keepalive Timer : 300s
related command
3.2. logout
command function
Quit CLI interface
command format
logout
For example
MEoC>>logout
3.3. who
command format
who
For example
MEoC>>who
+------------------------------------------------------+
| User Name | Login Channel | Login time |
+------------------------------------------------------+
| root | TELNET | Wed Apr 22 20:51:50 2009
+------------------------------------------------------+
42

EoC Telnet - Command Line

Uploaded by

EoC Telnet - Command Line

Uploaded by

No new Wires.... www.wodaplug.

Catalogue- Comand Lined description

2.2.18 set cnu_igmpsp_ctrl...............................................................................................30

2.4.1 del cnu......................................................................................................................46

Cablengine MEoC Configuration Environment

1.1 Configuration Environment

Fig.1.1 WEB management configuration environment

1.2 Steps of Configuration Environment

Setp 1As shown fig.1-1,Connect PC ,Master by switch .

1, the MEoC management for for common computer or server;

2.Cable Speed M240NR Command description

2.1.1. show cbat_info

Cpu Mac : 00:55:ff:01:00:01

2.1.2. show cbat_topo_info

Id Mac Address Status

2.1.3. show cbat_perf

Cpu Load cpu

2.1.4 show cbat_vlan_list

2.1.5 show cbat_vlan_info (vlanid)

2.1.6 show cbat_rt_stats

2.1.7 show card_info

2.1.8 show card_topo_info

Id Mac Address Status Access Authorize Tx Rx

2.1.9 show card_rf_info

2.1.10 show card_qos

TTL: CA0 CA1 CA2 CA3 MME

TX Buffer Allocation: Enable

Allocation: CA0 CA1 CA2 CA3

2.1.11 show analog_info

2.1.12 show cnu_info

Authorize authorization status

IgmpSp Mode : Disable

2.1.13 show cnu_qos

TTL: CA0 CA1 CA2 CA3 MME

TX Buffer Allocation: Enable

Allocation: CA0 CA1 CA2 CA3

2.1.14 show cnu_rt_stats

2.1.15 show default_cnu_config

Tx Buffer Allocation : Disable

2.1.16 show ip_access_list

2.1.17 show mgmt_vlan

2.1.18 show pre_cnu_list

2.1.19 show pre_cnu_config

Ethernet Port Info

2.1.20 show trap_server

2.1.21 show whitelist_info

2.1.22 show anonymitylist_info

2.2.1 set analog_alarm

2.2.3 set card_isolation

2.2.4 set card_qos_dscp

2.2.5 set card_qos_queue_threshold

set card_qos_queue_threshold (cardid) (queue) (percent)

2.2.6 set card_qos_queue_ttl

2.2.7 set card_qos_service_pri

2.2.8 set card_qos_threshold

2.2.9 set card_qos_tos

2.2.10 set card_qos_tos_mapping

2.2.11 set card_qos_vlan

2.2.12 set card_qos_vlan_mapping

2.2.13 set cbat_rt_stats_reset

2.2.14 set cbat_pvid (portid) (pvid)

2.2.15 set cbat_dot1q_vlan_mode (mode)

2.2.16 set cbat_bstorm_ctrl

2.2.17 set cbat_bstorm_rate

2.2.18 set cbat_flow_ctrl

2.2.19 set cbat_max_cnu_count

2.2.20 set cnu_bstorm_ctrl

MEOC>> set cnu_bstorm_ctrl 16 enable

2.2.21 set cnu_rt_stats_reset

2.2.22 set cnu_cable_speedlimit

2.2.23 set cnu_igmpsp_ctrl

2.2.24 set cnu_loopdetect_mode

2.2.25 set cnu_isolation

MEOC>> set cnu_isolation 16 disable

2.2.26 set cnu_maclimit

2.2.27 set cnu_mstorm_ctrl