Microprocessors and Interfacing Devices

Smartzworld.com Smartworld.
asia
LECTURE NOTES
ON
MICROPROCESSORS AND INTERFACING DEVICES
III B. Tech II semester

(JNTUH-R13)
ELECTRICAL AND ELECTRONICS ENGINEERING
jntuworldupdates.org Specworld.in
Smartzworld.com Smartworld.asia
Syllabus:
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
L T/ /P/D C
III Year B.Tech. EEE -II Sem 4 -/-/- 4
MICROPROCESSORS AND INTERFACING DEVICES
UNIT – I
8086 MICROPROCESSOR:
Introduction to 8085 microprocessor, 8086 architecture- Functional Diagram, Register Organization,
Memory segmentation, Memory addresses, physical memory organization, Signal descriptions of 8086-
common function signals, Minimum and Maximum mode signals, Read Write cycles, Timing diagrams,
Interrupt structure of 8086.
UNIT – II
ASSEMBLY LANGUAGE PROGRAMMING OF 8086:
Instruction formats, addressing modes, instruction set, assembler directives, macros, Simple programs
involving logical, branch and call instructions, Sorting, evaluating arithmetic expressions, string
manipulations.
UNIT – III
PERIPHERAL INTERFACING WITH 8086 MICROPROCESSOR:
8255 PPI, Keyboard, display controllers, Stepper motor, A/D & D/A Converter Interfacing with 8086
microprocessor.
Static and Dynamic memories, Vector interrupt table, Interrupt service routine, Introduction to DOS &
BIOS interrupts, Programmable Interrupt Controller 8259, DMA controller 8257 Interfacing with 8086
microprocessor.
UNIT – IV
COMMUNICATION INTERFACE:
Serial communication standards, serial data transfer schemes, 8251 USART architecture and Interfacing,
RS-232, IEEE-488, prototyping and trouble shooting.
UNIT – V
INTRODUCTION TO MICROCONTROLLERS:
Overview of 8051 microcontroller, Architecture, I/O ports and Memory organization, addressing modes
and instruction set of 8051, Simple programs.
UNIT-I
8086 ARCHITECTURE
Introduction to processor:
 A processor is the logic circuitry that responds to and processes the basic instructions that
drives a computer.
 The term processor has generally replaced the term central processing unit (CPU). The
processor in a personal computer or embedded in small devices is often called a
microprocessor.
 The processor (CPU, for Central Processing Unit) is the computer's brain. It allows the
processing of numeric data, meaning information entered in binary form, and the execution
of instructions stored in memory.
Evolution of Microprocessor:
A microprocessor is used as the CPU in a microcomputer. There are now many different
microprocessors available.
 Microprocessor is a program-controlled device, which fetches the instructions from memory,
decodes and executes the instructions. Most Micro Processor are single- chip devices.
 Microprocessor is a backbone of computer system. which is called CPU
 Microprocessor speed depends on the processing speed depends on DATA BUS WIDTH.
 A common way of categorizing microprocessors is by the no. of bits that their ALU can
Work with at a time
 The address bus is unidirectional because the address information is always given by the
Micro Processor to address a memory location of an input / output devices.
 The data bus is Bi-directional because the same bus is used for transfer of data between
Micro Processor and memory or input / output devices in both the direction.
 It has limitations on the size of data. Most Microprocessor does not support floating-point
operations.
 Microprocessor contain ROM chip because it contain instructions to execute data.
 What is the primary & secondary storage device? - In primary storage device the
 Storage capacity is limited. It has a volatile memory. In secondary storage device the storage
capacity is larger. It is a nonvolatile memory.
a) Primary devices are: RAM (Read / Write memory, High Speed, Volatile Memory)
/ ROM (Read only memory, Low Speed, Non Voliate Memory)
b) Secondary devices are: Floppy disc / Hard disk
Compiler: Compiler is used to translate the high-level language program into machine code at a
time. It doesn’t require special instruction to store in a memory, it stores automatically. The
Execution time is less compared to Interpreter.
1.4-bit Microprocessor:
 The first microprocessor (Intel 4004) was invented in 1971. It was a 4-bit calculation device
with a speed of 108 kHz. Since then, microprocessor power has grown exponentially. So
what exactly are these little pieces of silicone that run our computers(" Common Operating
Machine Particularly Used For Trade Education And Research ")
 It has 3200 PMOS transistors.
 It is a 4-bit device used in calculator.
2.8-Bit microprocessor:
 In 1972, Intel came out with the 8008 which is 8-bit.
 In 1974, Intel announced the 8080 followed by 8085 is a 8-bit processor Because 8085
processor has 8 bit ALU (Arithmetic Logic Review). Similarly 8086 processor has 16 bit
ALU. This had a larger instruction set then 8080. used NMOS transistors, so it operated
much faster than the 8008.
The 8080 is referred to as a “Second generation Microprocessor”
3. Limitations of 8 Bit microprocessor:
 Low speed of execution
 Low memory addressing capability
 Limited number of general purpose registers
 Less power full instruction set
4. Examples for 4/ 8 / 16 / 32 bit Microprocessors:
 4-Bit processor – 4004/4040
 8-bit Processor - 8085 / Z80 / 6800
 16-bit Processor - 8086 / 68000 / Z8000
 32-bit Processor - 80386 / 80486
5. What are 1st / 2nd / 3rd / 4th generation processor?
 The processor made of PMOS technology is called 1st generation processor, and it is made up
of 4 bits
 The processor made of NMOS technology is called 2nd generation processor, and it is made
up of 8 bits
 The processor made of CMOS technology is called 3rd generation processor, and it is made
up of 16 bits
 The processor made of HCMOS technology is called 4th generation processor, and it is made
up of 32 bits (HCMOS : High-density n- type Complementary Metal Oxide Silicon field
effect transistor)
Block diagram of microprocessor:
The Central Processing Unit (CPU):

This device coordinates all operations of a micro computer. It fetches programs stored in
ROM‟s or RAMs and executes the instructions depending one a specific Instructions set,
which is characteristic of each type of CPU, and which is recognized by the CPU.
The Random Access Memory (RAM): Temporary or trail programs are written.
Besides the ROM area, every computer has some memory space for temporary storage of
data as well as for programs under development. These memory devices are RAMs or Read – write
memory. The contents of it are not permanent and are altered when power is turned off. So the RAM
memory is considered to be volatile memory.
The Read Only Memory (ROM): Permanent programs are stored.
The permanent memory device/area is called ROM, because whatever be the memory
contents of ROMs, they cannot be over written with some other information.
For a blank ROM, the manufacturer supplies the device without any inf. In it, information
can be entered electrically into the memory space. This is called burning a ROM or PROM.
Data Lines/Data Bus:
The number of data lines, like add. Lines vary with the specific CPU .The set of data lines
is database like the address bus unlike add. Bus, the data bus is bidirectional because while the
information on the address Bus always flows out of the CPU; the data can flow both out of the CPU
as well as into the CPU.
Control lines/ control Bus:
The no. of control lines also depends on the specific CPU one is using.
Ex: Read; Write lines are examples of control lines
Clock: The clock is a symmetrical square wave signal that drives the CPU
Instructions: An instruction is an elementary operation that the processor can accomplish.
Instructions are stored in the main memory, waiting to be processed by the processor. An instruction
has two fields:
 Operation code, which represents the action that the processor must execute;
Operand code, which defines the parameters of the action. The operand code depends on the
operation. It can be data or a memory address
Introduction to 8085 Microprocessor:
The Salient Features of 8085 Microprocessor:
 8085 is an 8 bit microprocessor, manufactured with N-MOS technology.
 It has 16-bit address bus and hence can address up to 216 = 65536 bytes (64KB)
memory locations through A0-A15.
 The first 8 lines of address bus and 8 lines of data bus are multiplexed AD0 - AD7.
Data bus is a group of 8 lines D0 - D7.
 It supports external interrupt request.8085 consists of 16 bit program counter (PC)
and stack pointer (SP).
 Six 8-bit general purpose register arranged in pairs: BC, DE, HL.
 It requires a signal +5V power supply and can operate at 3 MHz, 5 MHz and 6
MHz Serial in/Serial out Port.
 It is enclosed with 40 pins DIP (Dual in line package).
Internal Architecture of 8085:
8085 Bus Structure: Address Bus:

 The address bus is a group of 16 lines generally identified as A0 to A15.
 The address bus is unidirectional: bits flow in one direction-from the MPU to peripheral
devices.
 The MPU uses the address bus to perform the first function: identifying a peripheral or a
memory location.
Data Bus:
 The data bus is a group of eight lines used for data flow.
 These lines are bi-directional - data flow in both directions between the MPU and
memory and peripheral devices.
 The MPU uses the data bus to perform the second function: transferring binary
information.
 The eight data lines enable the MPU to manipulate 8-bit data ranging from 00 to FF (28 =
256 numbers).
 The largest number that can appear on the data bus is 11111111.
Control Bus:
 The control bus carries synchronization signals and providing timing signals.
 The MPU generates specific control signals for every operation it performs. These signals
are used to identify a device type with which the MPU wants to communicate.
Registers of 8085:
 The 8085 have six general-purpose registers to store 8-bit data during program execution.
 These registers are identified as B, C, D, E, H, and L.
 They can be combined as register pairs-BC, DE, and HL-to perform some 16-bit
operations.
Accumulator (A):
 The accumulator is an 8-bit register that is part of the arithmetic/logic unit (ALU).
 This register is used to store 8-bit data and to perform arithmetic and logical operations.
 The result of an operation is stored in the accumulator.
Flags:
 The ALU includes five flip-flops that are set or reset according to the result of an
operation.
 The microprocessor uses the flags for testing the data conditions.
 They are Zero (Z), Carry (CY), Sign (S), Parity (P), and Auxiliary Carry (AC) flags. The
most commonly used flags are Sign, Zero, and Carry.
The bit position for the flags in flag register is,
1. Sign Flag (S):

After execution of any arithmetic and logical operation, if D7 of the result is 1, the sign flag
is set. Otherwise it is reset.
D7 is reserved for indicating the sign; the remaining is the magnitude of number.
If D7 is 1, the number will be viewed as negative number. If D7 is 0, the number will be
viewed as positive number.
2. Zero Flag (z):

If the result of arithmetic and logical operation is zero, then zero flag is set otherwise it is
reset.
3. Auxiliary Carry Flag (AC):
If D3 generates any carry when doing any arithmetic and logical operation, this flag is set.
Otherwise it is reset.
4. Parity Flag (P):
If the result of arithmetic and logical operation contains even number of 1's then this flag
will be set and if it is odd number of 1's it will be reset.
5. Carry Flag (CY):

If any arithmetic and logical operation result any carry then carry flag is set otherwise it is
reset.
Arithmetic and Logic Unit (ALU):
 It is used to perform the arithmetic operations like addition, subtraction, multiplication,
division, increment and decrement and logical operations like AND, OR and EX-OR.
 It receives the data from accumulator and registers.
 According to the result it set or reset the flags.
Program Counter (PC):
 This 16-bit register sequencing the execution of instructions.
 It is a memory pointer. Memory locations have 16-bit addresses, and that is why this is a
16-bit register.
 The function of the program counter is to point to the memory address of the next
instruction to be executed.
 When an opcode is being fetched, the program counter is incremented by one to point to
the next memory location.
Stack Pointer (SP):
 The stack pointer is also a 16-bit register used as a memory pointer.
 It points to a memory location in R/W memory, called the stack.
 The beginning of the stack is defined by loading a 16-bit address in the stack pointer
(register).
Temporary Register: It is used to hold the data during the arithmetic and logical operations.
Instruction Register: When an instruction is fetched from the memory, it is loaded in the
instruction register.
Instruction Decoder: It gets the instruction from the instruction register and decodes the
instruction. It identifies the instruction to be performed.
Serial I/O Control: It has two control signals named SID and SOD for serial data transmission.
Timing and Control unit:
 It has three control signals ALE, RD (Active low) and WR (Active low) and three status
signals IO/M(Active low), S0 and S1.
 ALE is used for provide control signal to synchronize the components of microprocessor
and timing for instruction to perform the operation.
 RD (Active low) and WR (Active low) are used to indicate whether the operation is
reading the data from memory or writing the data into memory respectively.
 IO/M(Active low) is used to indicate whether the operation is belongs to the memory or
peripherals.
 If,
Interrupt Control Unit:

 It receives hardware interrupt signals and sends an acknowledgement for receiving the
interrupt signal.
Pin Diagram and Pin Description Of 8085
8085 is a 40 pin IC, DIP package. The signals from the pins can be grouped as follows
1. Power supply and clock signals
2. Address bus
3. Data bus
4. Control and status signals
5. Interrupts and externally initiated signals
6. Serial I/O ports
1. Power supply and clock frequency signals
 Vcc + 5 volt power supply

 Vss Ground
 X1, X2: Crystal or R/C network or LC network connections to set the
frequency of internal clock generator.
 The frequency is internally divided by two. Since the basic operating timing
frequency is 3 MHz, a 6 MHz crystal is connected externally.
 CLK (output)-Clock Output is used as the system clock for peripheral and
devices interfaced with the microprocessor.
2. Address Bus:

A8 - A15 (output; 3-state)

It carries the most significant 8 bits of the memory address or the 8 bits of
the I/O address;
3. Multiplexed Address / Data Bus:
 AD0 - AD7 (input/output; 3-state)
 These multiplexed set of lines used to carry the lower order 8 bit address as well as data
bus.
 During the opcode fetch operation, in the first clock cycle, the lines deliver the lower
order address A0 - A7.
 In the subsequent IO / memory, read / write clock cycle the lines are used as data bus.
 The CPU may read or write out data through these lines.
4. Control and Status signals:
 ALE (output) - Address Latch Enable.
 This signal helps to capture the lower order address presented on the multiplexed address
/ data bus.
 RD (output 3-state, active low) - Read memory or IO device.
 This indicates that the selected memory location or I/O device is to be read and that the
data bus is ready for accepting data from the memory or I/O device.
 WR (output 3-state, active low) - Write memory or IO device.
 This indicates that the data on the data bus is to be written into the selected memory
location or I/O device.
 IO/M (output) - Select memory or an IO device.
 This status signal indicates that the read / write operation relates to whether the memory
or I/O device.
 It goes high to indicate an I/O operation.
 It goes low for memory operations.
5. Status Signals:
 It is used to know the type of current operation of the microprocessor.
6. Interrupts and externally initiated operations:

 They are the signals initiated by an external device to request the microprocessor to do a
particular task or work.
 There are five hardware interrupts called,
 On receipt of an interrupt, the microprocessor acknowledges the interrupt by the active

low INTA (Interrupt Acknowledge) signal.
Reset In (input, active low)

 This signal is used to reset the microprocessor.
 The program counter inside the microprocessor is set to zero.
 The buses are tri-stated.
Reset Out (Output)
 It indicates CPU is being reset.
 Used to reset all the connected devices when the microprocessor is reset
7. Direct Memory Access (DMA):
Tri state devices:
 3 output states are high & low states and additionally a high impedance state.
 When enable E is high the gate is enabled and the output Q can be 1 or 0 (if A is 0, Q is 1,
otherwise Q is 0). However, when E is low the gate is disabled and the output Q enters into a
high impedance state.
 For both high and low states, the output Q draws a current from the input of the OR gate.
 When E is low, Q enters a high impedance state; high impedance means it is electrically
isolated from the OR gate's input, though it is physically connected. Therefore, it does not
draw any current from the OR gate's input.
 When 2 or more devices are connected to a common bus, to prevent the devices from
interfering with each other, the tristate gates are used to disconnect all devices except the one
that is communicating at a given instant.
 The CPU controls the data transfer operation between memory and I/O device. Direct
Memory Access operation is used for large volume data transfer between memory and an I/O
device directly.
 The CPU is disabled by tri-stating its buses and the transfer is effected directly by
external control circuits.
 HOLD signal is generated by the DMA controller circuit. On receipt of this signal, the
microprocessor acknowledges the request by sending out HLDA signal and leaves out the
control of the buses. After the HLDA signal the DMA controller starts the direct transfer of
data.
READY (input)
 Memory and I/O devices will have slower response compared to microprocessors.
 Before completing the present job such a slow peripheral may not be able to handle
further data or control signal from CPU.
 The processor sets the READY signal after completing the present job to access the data.
 The microprocessor enters into WAIT state while the READY pin is disabled.
8. Single Bit Serial I/O ports:
 SID (input) - Serial input data line

 SOD (output) - Serial output data line
 These signals are used for serial communication.
Overview or Features of 8086
 It is a 16-bit Microprocessor (μp).It’s ALU, internal registers works with 16bit binary
word.
20
 8086 has a 20 bit address bus can access up to 2 = 1 MB memory locations.
 8086 has a 16bit data bus. It can read or write data to a memory/port either 16bits or 8 bit
at a time.
 It can support up to 64K I/O ports.
 It provides 14, 16 -bit registers.
 Frequency range of 8086 is 6-10 MHz
 It has multiplexed address and data bus AD0- AD15 and A16 – A19.
 It requires single phase clock with 33% duty cycle to provide internal timing.
 It can prefetch upto 6 instruction bytes from memory and queues them in order to speed
up instruction execution.
 It requires +5V power supply.
 A 40 pin dual in line package.
 8086 is designed to operate in two modes, Minimum mode and Maximum mode.
o The minimum mode is selected by applying logic 1 to the MN / MX# input pin.
This is a single microprocessor configuration.
o The maximum mode is selected by applying logic 0 to the MN / MX# input pin.
This is a multi micro processors configuration.
Register Organization of 8086 General
purpose registers
The 8086 microprocessor has a total of fourteen registers that are accessible to the
programmer. It is divided into four groups. They are:
 Four General purpose registers
 Four Index/Pointer registers
 Four Segment registers
 Two Other registers
General purpose registers:
Accumulator register consists of two 8-bit registers AL and AH, which can be combined
together and used as a 16-bit register AX. AL in this case contains the low order byte of the
word, and AH contains the high-order byte. Accumulator can be used for I/O operations and
string manipulation.
Base register consists of two 8-bit registers BL and BH, which can be combined together
and used as a 16-bit register BX. BL in this case contains the low-order byte of the word, and BH
contains the high-order byte. BX register usually contains a data pointer used for based, based
indexed or register indirect addressing.
Count register consists of two 8-bit registers CL and CH, which can be combined together
and used as a 16-bit register CX. When combined, CL register contains the low order byte of
the word, and CH contains the high-order byte. Count register can be used in Loop,
shift/rotate instructions and as a counter in string manipulation
Data register consists of two 8-bit registers DL and DH, which can be combined together
and used as a 16-bit register DX. When combined, DL register contains the low order byte of the
word, and DH contains the high-order byte. Data register can be used as a port number in I/O
operations. In integer 32-bit multiply and divide instruction the DX register contains high-order
word of the initial or resulting number.
Index or Pointer Registers

These registers can also be called as Special Purpose registers.
Stack Pointer (SP) is a 16-bit register pointing to program stack, i.e. it is used to hold the
address of the top of stack. The stack is maintained as a LIFO with its bottom at the start of the
stack segment (specified by the SS segment register).Unlike the SP register, the BP can be used
to specify the offset of other program segments.
Base Pointer (BP) is a 16-bit register pointing to data in stack segment. It is usually used
by subroutines to locate variables that were passed on the stack by a calling program. BP register
is usually used for based, based indexed or register indirect addressing.
Source Index (SI) is a 16-bit register. SI is used for indexed, based indexed and register
indirect addressing, as well as a source data address in string manipulation instructions. Used in
conjunction with the DS register to point to data locations in the data segment.
Destination Index (DI) is a 16-bit register. Used in conjunction with the ES register in
string operations. DI is used for indexed, based indexed and register indirect addressing, as well
as a destination data address in string manipulation instructions. In short, Destination Index and
SI Source Index registers are used to hold address.
Segment Registers
Most of the registers contain data/instruction offsets within 64 KB memory segment.
There are four different 64 KB segments for instructions, stack, data and extra data. To specify
where in 1 MB of processor memory these 4 segments are located the processor uses four
segment registers.
Code segment (CS) is a 16-bit register containing address of 64 KB segment with

processor instructions. The processor uses CS segment for all accesses to instructions referenced
by instruction pointer (IP) register. CS register cannot be changed directly. The CS register is
automatically updated during far jump, far call and far return instructions.
Stack segment (SS) is a 16-bit register containing address of 64KB segment with
program stack. By default, the processor assumes that all data referenced by the stack pointer
(SP) and base pointer (BP) registers is located in the stack segment. SS register can be changed
directly using POP instruction.
Data segment (DS) is a 16-bit register containing address of 64KB segment with program
data. By default, the processor assumes that all data referenced by general registers (AX, BX,
CX, DX) and index register (SI, DI) is located in the data segment. DS register can be changed
directly using POP and LDS instructions.
Extra segment (ES) used to hold the starting address of Extra segment. Extra segment is
provided for programs that need to access a second data segment. Segment registers cannot be
used in arithmetic operations.
Other registers of 8086
Instruction Pointer (IP) is a 16-bit register. This is a crucially important register which is used
to control which instruction the CPU executes. The IP, or program counter, is used to store the
memory location of the next instruction to be executed. The CPU checks the program counter to
ascertain which instruction to carry out next. It then updates the program counter to point to the
next instruction. Thus the program counter will always point to the next instruction to be
executed.
Flag Register contains a group of status bits called flags that indicate the status of the CPU or
the result of arithmetic operations. There are two types of flags:
1. The status flags which reflect the result of executing an instruction. The programmer cannot
set/reset these flags directly.
2. The control flags enable or disable certain CPU operations. The programmer can set/reset
these bits to control the CPU's operation.
Nine individual bits of the status register are used as control flags (3 of them) and status
flags (6 of them).The remaining 7 are not used.
A flag can only take on the values 0 and 1. We say a flag is set if it has the value
1.The status flags are used to record specific characteristics of arithmetic and of logical
instructions.
Control Flags: There are three control flags
1. The Direction Flag (D): Affects the direction of moving data blocks by such
instructions as MOVS, CMPS and SCAS. The flag values are 0 = up and 1 = down and
can be set/reset by the STD (set D) and CLD (clear D) instructions.
2. The Interrupt Flag (I): Dictates whether or not system interrupts can occur.
Interrupts are actions initiated by hardware block such as input devices that will interrupt
the normal execution of programs. The flag values are 0 = disable interrupts or 1 =
enable interrupts and can be manipulated by the CLI (clear I) and STI (set I)
instructions.
3. The Trap Flag (T): Determines whether or not the CPU is halted after the execution
of each instruction. When this flag is set (i.e. = 1), the programmer can single step
through his program to debug any errors. When this flag = 0 this feature is off. This
flag can be set by the INT 3 instruction.
Status Flags: There are six status flags
1. The Carry Flag (C): This flag is set when the result of an unsigned arithmetic operation is
too large to fit in the destination register. This happens when there is an end carry in an addition
operation or there an end borrows in a subtraction operation. A value of 1 = carry and 0 = no
carry.
2. The Overflow Flag (O): This flag is set when the result of a signed arithmetic operation is too
large to fit in the destination register (i.e. when an overflow occurs). Overflow can occur when
adding two numbers with the same sign (i.e. both positive or both negative). A value of 1 =
overflow and 0 = no overflow.
3. The Sign Flag (S): This flag is set when the result of an arithmetic or logic operation is
negative. This flag is a copy of the MSB of the result (i.e. the sign bit). A value of 1 means
negative and 0 = positive.
4. The Zero Flag (Z): This flag is set when the result of an arithmetic or logic operation is equal
to zero. A value of 1 means the result is zero and a value of 0 means the result is not zero.
5. The Auxiliary Carry Flag (A): This flag is set when an operation causes a carry from bit 3 to
bit 4 (or a borrow from bit 4 to bit 3) of an operand. A value of 1 = carry and 0 = no carry.
6. The Parity Flag (P): This flags reflects the number of 1s in the result of an operation. If the
number of 1s is even its value = 1 and if the number of 1s is odd then its value = 0.
Architecture of 8086 or Functional Block diagram of 8086
 8086 has two blocks Bus Interface Unit (BIU) and Execution Unit (EU).
 The BIU performs all bus operations such as instruction fetching, reading and writing
operands for memory and calculating the addresses of the memory operands. The
instruction bytes are transferred to the instruction queue.
 EU executes instructions from the instruction system byte queue.
 Both units operate asynchronously to give the 8086 an overlapping instruction fetch and
execution mechanism which is called as Pipelining. This results in efficient use of the
system bus and system performance.
 BIU contains Instruction queue, Segment registers, Instruction pointer, Address adder.
 EU contains Control circuitry, Instruction decoder, ALU, Pointer and Index register, Flag
register.
Figure: 8086 Architecture

Explanation of Architecture of 8086
Bus Interface Unit:
 It provides a full 16 bit bidirectional data bus and 20 bit address bus.
 The bus interface unit is responsible for performing all external bus operations.
 Specifically it has the following functions:
 Instruction fetch Instruction queuing, Operand fetch and storage, Address relocation and Bus
control.
 The BIU uses a mechanism known as an instruction stream queue to implement pipeline
architecture.
 This queue permits prefetch of up to six bytes of instruction code. When ever the queue of
the BIU is not full, it has room for at least two more bytes and at the same time the EU is not
requesting it to read or write operands from memory, the BIU is free to look ahead in the
program by prefetching the next sequential instruction.
 These prefetching instructions are held in its FIFO queue. With its 16 bit data bus, the BIU
fetches two instruction bytes in a single memory cycle.
 After a byte is loaded at the input end of the queue, it automatically shifts up through the
FIFO to the empty location nearest the output.
 The EU accesses the queue from the output end. It reads one instruction byte after the
other from the output of the queue. If the queue is full and the EU is not requesting access to
operand in memory.
 These intervals of no bus activity, which may occur between bus cycles are known as Idle
state.
 If the BIU is already in the process of fetching an instruction when the EU request it to read
or write operands from memory or I/O, the BIU first completes the instruction fetch bus cycle
before initiating the operand read / write cycle.
 The BIU also contains a dedicated adder which is used to generate the 20bit physical
address that is output on the address bus. This address is formed by adding an appended 16
bit segment address and a 16 bit offset address.
 For example: The physical address of the next instruction to be fetched is formed by
combining the current contents of the code segment CS register and the current contents of the
instruction pointer IP register.
 The BIU is also responsible for generating bus control signals such as those for memory read
or write and I/O read or write.
Execution Unit
 The Execution unit is responsible for decoding and executing all instructions.
 The EU extracts instructions from the top of the queue in the BIU, decodes them,
generates operands if necessary, passes them to the BIU and requests it to perform the read or
write bus cycles to memory or I/O and perform the operation specified by the instruction on
the operands.
 During the execution of the instruction, the EU tests the status and control flags and
updates them based on the results of executing the instruction.
 If the queue is empty, the EU waits for the next instruction byte to be fetched and shifted
to top of the queue.
 When the EU executes a branch or jump instruction, it transfers control to a location

corresponding to another set of sequential instructions.
 Whenever this happens, the BIU automatically resets the queue and then begins to fetch
instructions from this new location to refill the queue.
General Bus Operation
 The 8086 has a combined address and data bus commonly referred as a time multiplexed
address and data bus.
 The main reason behind multiplexing address and data over the same pins is the
maximum utilization of processor pins and it facilitates the use of 40 pin standard DIP
package.
 The bus can be demultiplexed using a few latches and transceivers, when ever required.
 Basically, all the processor bus cycles consist of at least four clock cycles. These are
referred to as T1, T2, T3, and T4. The address is transmitted by the processor during T1. It is
present on the bus only for one cycle.
 The negative edge of this ALE pulse is used to separate the address and the data or status
information. In maximum mode, the status lines S0, S1 and S2 are used to indicate the type of
operation.
 Status bits S3 to S7 are multiplexed with higher order address bits and the BHE signal.
Address is valid during T1 while status bits S3 to S7 are valid during T2 through T4.
Maximum mode
 In the maximum mode, the 8086 is operated by strapping the MN/MX pin to ground.
 In this mode, the processor derives the status signal S2, S1, S0. Another chip called bus
controller derives the control signal using this status information.
 In the maximum mode, there may be more than one microprocessor in the system
configuration.
Minimum mode
 In a minimum mode 8086 system, the microprocessor 8086 is operated in minimum

mode by strapping its MN/MX pin to logic 1.
 In this mode, all the control signals are given out by the microprocessor chip itself.
 There is a single microprocessor in the minimum mode system.
Pin Diagram of 8086 and Pin description of 8086
Figure shows the Pin diagram of 8086. The description follows it.
 The Microprocessor 8086 is a 16-bit CPU available in different clock rates and packaged
in a 40 pin CERDIP or plastic package.
 The 8086 operates in single processor or multiprocessor configuration to achieve high

performance. The pins serve a particular function in minimum mode (single processor
mode) and other function in maximum mode configuration (multiprocessor mode).
 The 8086 signals can be categorized in three groups.
o The first are the signal having common functions in minimum as well as
maximum mode.
o The second are the signals which have special functions for minimum mode
o The third are the signals having special functions for maximum mode.
 The following signal descriptions are common for both modes.
 AD15-AD0: These are the time multiplexed memory I/O address and data lines.
o Address remains on the lines during T1 state, while the data is available on the data
bus during T2, T3, Tw and T4. These lines are active high and float to a tristate
during interrupt acknowledge and local bus hold acknowledge cycles.
 A19/S6, A18/S5, A17/S4, and A16/S3: These are the time multiplexed address and
status lines.
o During T1 these are the most significant address lines for memory operations.
o During I/O operations, these lines are low.
o During memory or I/O operations, status information is available on those lines for
T2, T3, Tw and T4.
o The status of the interrupt enable flag bit is updated at the beginning of each clock
cycle.
o The S4 and S3 combine indicate which segment registers is presently being used for
memory accesses as in below fig
o These lines float to tri-state off during the local bus hold acknowledge. The status line
S6 is always low.
o The address bit is separated from the status bit using latches controlled by the
ALE signal.
 BHE/S7: The bus high enable is used to indicate the transfer of data over the higher order
(D15-D8) data bus as shown in table. It goes low for the data transfer over D15-D8 and is used
to derive chip selects of odd address memory bank or peripherals. BHE is low during
T1 for read, write and interrupt acknowledge cycles, whenever a byte is to be transferred
on higher byte of data bus. The status information is available during T2, T3 and T4. The
signal is active low and tristated during hold. It is low during T1 for the first pulse of the
interrupt acknowledge cycle.
 RD – Read: This signal on low indicates the peripheral that the processor is performing
memory or I/O read operation. RD is active low and shows the state for T2, T3, Tw of any
read cycle. The signal remains tristated during the hold acknowledge.
 READY: This is the acknowledgement from the slow device or memory that they have
completed the data transfer. The signal made available by the devices is synchronized by the
8284A clock generator to provide ready input to the 8086. the signal is active high.
 INTR-Interrupt Request: This is a triggered input. This is sampled during the last clock
cycles of each instruction to determine the availability of the request. If any interrupt
request is pending, the processor enters the interrupt acknowledge cycle. This can be
internally masked by resulting the interrupt enable flag. This signal is active high and
internally synchronized.
 TEST: This input is examined by a ‘WAIT’ instruction. If the TEST pin goes low,
execution will continue, else the processor remains in an idle state. The input is
synchronized internally during each clock cycle on leading edge of clock.
 CLK- Clock Input: The clock input provides the basic timing for processor operation and
bus control activity. It’s an asymmetric square wave with 33% duty cycle.
Figure shows the Pin functions of 8086.
The following pin functions are for the minimum mode operation of 8086.
 M/IO – Memory/IO: This is a status line logically equivalent to S2 in maximum mode.

When it is low, it indicates the CPU is having an I/O operation, and when it is high, it
indicates that the CPU is having a memory operation. This line becomes active high in the
previous T4 and remains active till final T4 of the current cycle. It is tristated during local
bus “hold acknowledge “.
 INTA – Interrupt Acknowledge: This signal is used as a read strobe for interrupt
acknowledge cycles. i.e. when it goes low, the processor has accepted the interrupt.
 ALE – Address Latch Enable: This output signal indicates the availability of the valid
address on the address/data lines, and is connected to latch enable input of latches. This
signal is active high and is never tristated.
 DT/R – Data Transmit/Receive: This output is used to decide the direction of data flow
through the transceivers (bidirectional buffers). When the processor sends out data, this
signal is high and when the processor is receiving data, this signal is low.
 DEN – Data Enable: This signal indicates the availability of valid data over the address/data
lines. It is used to enable the transceivers (bidirectional buffers) to separate the data from the
multiplexed address/data signal. It is active from the middle of T2 until the middle of T4. This
is tristated during ‘hold acknowledge’ cycle.
 HOLD, HLDA- Acknowledge: When the HOLD line goes high; it indicates to the
processor that another master is requesting the bus access. The processor, after receiving the
HOLD request, issues the hold acknowledge signal on HLDA pin, in the middle of the next
clock cycle after completing the current bus cycle.
 At the same time, the processor floats the local bus and control lines. When the processor
detects the HOLD line low, it lowers the HLDA signal. HOLD is an asynchronous input, and
is should be externally synchronized. If the DMA request is made while the CPU is
performing a memory or I/O cycle, it will release the local bus during T4 provided :
1. The request occurs on or before T2 state of the current cycle.
2. The current cycle is not operating over the lower byte of a word.
3. The current cycle is not the first acknowledge of an interrupt acknowledge sequence.
4. A Lock instruction is not being executed.
The following pin functions are applicable for maximum mode operation of 8086.
 S2, S1, and S0 – Status Lines: These are the status lines which reflect the type of
operation, being carried out by the processor. These become activity during T4 of the
previous cycle and active during T1 and T2 of the current bus cycles.
 LOCK: This output pin indicates that other system bus master will be prevented from
gaining the system bus, while the LOCK signal is low. The LOCK signal is activated by the
‘LOCK’ prefix instruction and remains active until the completion of the next instruction.
When the CPU is executing a critical instruction which requires the system bus, the LOCK
prefix instruction ensures that other processors connected in the system will not gain the
control of the bus.
The 8086, while executing the prefixed instruction, asserts the bus lock signal output,
which may be connected to an external bus controller. By prefetching the instruction, there is a
considerable speeding up in instruction execution in 8086. This is known as instruction
pipelining.
 At the starting the CS: IP is loaded with the required address from which the execution is
to be started. Initially, the queue will be empty and the microprocessor starts a fetch
operation to bring one byte (the first byte) of instruction code, if the CS: IP address is odd
or two bytes at a time, if the CS: IP address is even.
 The first byte is a complete opcode in case of some instruction (one byte opcode instruction)
and is a part of opcode, in case of some instructions (two byte opcode instructions), the
remaining part of code lie in second byte.
 The second byte is then decoded in continuation with the first byte to decide the instruction
length and the number of subsequent bytes to be treated as instruction data. The queue is
updated after every byte is read from the queue but the fetch cycle is initiated by BIU
only if at least two bytes of the queue are empty and the EU may be concurrently
executing the fetched instructions.
 The next byte after the instruction is completed is again the first opcode byte of the next
instruction. A similar procedure is repeated till the complete execution of the program. The
fetch operation of the next instruction is overlapped with the execution of the current
instruction. As in the architecture, there are two separate units, namely Execution unit and
Bus interface unit.
 While the execution unit is busy in executing an instruction, after it is completely decoded,
the bus interface unit may be fetching the bytes of the next instruction from memory,
depending upon the queue status.
 RQ/GT0, RQ/GT1 – Request/Grant: These pins are used by the other local bus master
in maximum mode, to force the processor to release the local bus at the end of the
processor current bus cycle.
 Each of the pin is bidirectional with RQ/GT0 having higher priority than RQ/GT1.
RQ/GT pins have internal pull-up resistors and may be left unconnected. Request/Grant
sequence is as follows:
1. A pulse of one clock wide from another bus master requests the bus access to
8086.
2. During T4(current) or T1(next) clock cycle, a pulse one clock wide from 8086 to
the requesting master, indicates that the 8086 has allowed the local bus to float
and that it will enter the ‘hold acknowledge’ state at next cycle. The CPU bus
interface unit is likely to be disconnected from the local bus of the system.
3. A one clock wide pulse from another master indicates to the 8086 that the hold
request is about to end and the 8086 may regain control of the local bus at the
next clock cycle. Thus each master to master exchange of the local bus is a
sequence of 3 pulses. There must be at least one dead clock cycle after each bus
exchange. The request and grant pulses are active low. For the bus request those
are received while 8086 is performing memory or I/O cycle, the granting of the
bus is governed by the rules as in case of HOLD and HLDA in minimum mode.
Minimum Mode 8086 System
Minimum mode 8086 system
 In a minimum mode 8086 system, the microprocessor 8086 is operated in minimum

mode by strapping its MN/MX pin to logic 1.
 In this mode, all the control signals are given out by the microprocessor chip itself. There
is a single microprocessor in the minimum mode system.
 The remaining components in the system are latches, transceivers, clock generator,
memory and I/O devices. Some type of chip selection logic may be required for selecting
memory or I/O devices, depending upon the address map of the system.
 Latches are generally buffered output D-type flip-flops like 74LS373 or 8282. They are
used for separating the valid address from the multiplexed address/data signals and are
controlled by the ALE signal generated by 8086.
 Transceivers are the bidirectional buffers and some times they are called as data
amplifiers. They are required to separate the valid data from the time multiplexed
address/data signals.
 They are controlled by two signals namely, DEN and DT/R.
 The DEN signal indicates the direction of data, i.e. from or to the processor. The system
contains memory for the monitor and users program storage.
 Usually, EPROM is used for monitor storage, while RAM for users program storage. A
system may contain I/O devices.
Write Cycle Timing Diagram for Minimum Mode
 The working of the minimum mode configuration system can be better described in terms
of the timing diagrams rather than qualitatively describing the operations.
 The opcode fetch and read cycles are similar. Hence the timing diagram can be
categorized in two parts, the first is the timing diagram for read cycle and the second is
the timing diagram for write cycle.
 The read cycle begins in T1 with the assertion of address latch enable (ALE) signal and also
M / IO signal. During the negative going edge of this signal, the valid address is latched
on the local bus.
 The BHE and A0 signals address low, high or both bytes. From T1 to T4 , the M/IO
signal indicates a memory or I/O operation.
 At T2, the address is removed from the local bus and is sent to the output. The bus is then
tristated. The read (RD) control signal is also activated in T2.
 The read (RD) signal causes the address device to enable its data bus drivers. After RD goes
low, the valid data is available on the data bus.
 The addressed device will drive the READY line high. When the processor returns the read
signal to high level, the addressed device will again tristate its bus drivers.
 A write cycle also begins with the assertion of ALE and the emission of the address. The
M/IO signal is again asserted to indicate a memory or I/O operation. In T2, after sending the
address in T1, the processor sends the data to be written to the addressed location.
 The data remains on the bus until middle of T4 state. The WR becomes active at the
beginning of T2 (unlike RD is somewhat delayed in T2 to provide time for floating).
 The BHE and A0 signals are used to select the proper byte or bytes of memory or I/O
word to be read or write.
 The M/IO, RD and WR signals indicate the type of data transfer as specified in table
below.
Bus Request and Bus Grant Timings in Minimum Mode System of 8086
 Hold Response sequence: The HOLD pin is checked at leading edge of each clock pulse.
If it is received active by the processor before T4 of the previous cycle or during T1 state
of the current cycle, the CPU activates HLDA in the next clock cycle and for succeeding
bus cycles, the bus will be given to another requesting master.
 The control of the bus is not regained by the processor until the requesting master does
not drop the HOLD pin low. When the request is dropped by the requesting master, the
HLDA is dropped by the processor at the trailing edge of the next clock.
Maximum Mode 8086 System
 In the maximum mode, the 8086 is operated by strapping the MN/MX pin to ground.
 In this mode, the processor derives the status signal S2, S1, S0. Another chip called bus
controller derives the control signal using this status information.
 In the maximum mode, there may be more than one microprocessor in the system
configuration.
 The components in the system are same as in the minimum mode system.
 The basic function of the bus controller chip IC8288 is to derive control signals like RD
and WR (for memory and I/O devices), DEN, DT/R, ALE etc. using the information by
the processor on the status lines.
 The bus controller chip has input lines S2, S1, S0 and CLK. These inputs to 8288 are
driven by CPU.
 It derives the outputs ALE, DEN, DT/R, MRDC, MWTC, AMWC, IORC, IOWC and
AIOWC. The AEN, IOB and CEN pins are especially useful for multiprocessor systems.
 AEN and IOB are generally grounded. CEN pin is usually tied to +5V. The significance of
the MCE/PDEN output depends upon the status of the IOB pin.
 If IOB is grounded, it acts as master cascade enable to control cascade 8259A, else it acts as
peripheral data enable used in the multiple bus configurations.
 INTA pin used to issue two interrupt acknowledge pulses to the interrupt controller or to an
interrupting device.
 IORC, IOWC are I/O read command and I/O write command signals respectively.
 These signals enable an IO interface to read or write the data from or to the address port.
 The MRDC, MWTC are memory read command and memory write command signals
respectively and may be used as memory read or write signals.
 All these command signals instructs the memory to accept or send data from or to the
bus.
 For both of these write command signals, the advanced signals namely AIOWC and
AMWTC are available.
 Here the only difference between in timing diagram between minimum mode and
maximum mode is the status signals used and the available control and advanced
command signals.
 R0, S1, S2 are set at the beginning of bus cycle.8288 bus controller will output a pulse as
on the ALE and apply a required signal to its DT / R pin during T1.
 In T2, 8288 will set DEN=1 thus enabling transceivers, and for an input it will activate
MRDC or IORC. These signals are activated until T4. For an output, the AMWC or
AIOWC is activated from T2 to T4 and MWTC or IOWC is activated from T3 to T4.
 The status bit S0 to S2 remains active until T3 and become passive during T3 and T4.
 If reader input is not activated before T3, wait state will be inserted between T3 and T4.
Memory Read Timing Diagram in Maximum Mode of 8086
Memory Write Timing in Maximum mode of 8086
RQ/GT Timings in Maximum Mode
 The request/grant response sequence contains a series of three pulses. The request/grant
pins are checked at each rising pulse of clock input.
 When a request is detected and if the condition for HOLD request is satisfied, the
processor issues a grant pulse over the RQ/GT pin immediately during T4 (current) or T1
(next) state.
 When the requesting master receives this pulse, it accepts the control of the bus, it sends a
release pulse to the processor using RQ/GT pin.
Minimum Mode Interface
 When the Minimum mode operation is selected, the 8086 provides all control
signals needed to implement the memory and I/O interface.
 The minimum mode signal can be divided into the following basic groups :
1. Address/data bus
2. Status
3. Control
4. Interrupt and
5. DMA.
Each and every group is explained clearly.
Address/Data Bus:
 These lines serve two functions. As an address bus is 20 bits long and consists of
signal lines A0 through A19. A19 represents the MSB and A0 LSB. A 20bit address
gives the 8086 a 1Mbyte memory address space. More over it has an independent
I/O address space which is 64K bytes in length.
 The 16 data bus lines D0 through D15 are actually multiplexed with address lines
A0 through A15 respectively. By multiplexed we mean that the bus work as an
address bus during first machine cycle and as a data bus during next machine cycles.
 D15 is the MSB and D0 LSB. When acting as a data bus, they carry read/write data
for memory, input/output data for I/O devices, and interrupt type codes from an
interrupt controller.
Status signal:
 The four most significant address lines A19 through A16 are also multiplexed but in
this case with status signals S6 through S3.
 These status bits are output on the bus at the same time that data are transferred over
the other bus lines.
 Bit S4 and S3 together from a 2 bit binary code that identifies which of the 8086
internal segment registers is used to generate the physical address that was output on
the address bus during the current bus cycle. Code S4S3 = 00 identifies a register
known as extra segment register as the source of the segment address.
 Status line S5 reflects the status of another internal characteristic of the 8086. It is
the logic level of the internal enable flag. The last status bit S6 is always at the logic 0
level.
Control Signals:
 The control signals are provided to support the 8086 memory I/O interfaces. They
control functions such as when the bus is to carry a valid address in which direction data
are to be transferred over the bus, when valid write data are on the bus and when to put
read data on the system bus.
 ALE is a pulse to logic 1 that signals external circuitry when a valid address word is on
the bus. This address must be latched in external circuitry on the 1-to-0 edge of the pulse
at ALE.
 Another control signal that is produced during the bus cycle is BHE bank high enable.
Logic 0 on this used as a memory enable signal for the most significant byte half of the
data bus D8 through D1. These lines also serve a second function, which is as the S7
status line.
 Using the M/IO and DT/R lines, the 8086 signals which type of bus cycle is in progress
and in which direction data are to be transferred over the bus. The logic level of M/IO
tells external circuitry whether a memory or I/O transfer is taking place over the bus.
Logic 1 at this output signals a memory operation and logic 0 an I/O operation.
 The direction of data transfer over the bus is signaled by the logic level output at DT/R.
When this line is logic 1 during the data transfer part of a bus cycle, the bus is in the
transmit mode. Therefore, data are either written into memory or output to an I/O device.
On the other hand, logic 0 at DT/R signals that the bus is in the receive mode. This
corresponds to reading data from memory or input of data from an input port.
 The signals read RD and write WR indicates that a read bus cycle or a write bus cycle is
in progress. The 8086 switches WR to logic 0 to signal external device that valid write or
output data are on the bus.
 On the other hand, RD indicates that the 8086 is performing a read of data of the bus.
During read operations, one other control signal is also supplied. This is DEN (data
enable) and it signals external devices when they should put data on the bus. There is one
other control signal that is involved with the memory and I/O interface. This is the
READY signal.
 READY signal is used to insert wait states into the bus cycle such that it is extended by a
number of clock periods. This signal is provided by an external clock generator device
and can be supplied by the memory or I/O sub-system to signal the 8086 when they are
ready to permit the data transfer to be completed.
Interrupt signals:
 The key interrupt interface signals are interrupt request (INTR) and interrupt
acknowledge (INTA).
 INTR is an input to the 8086 that can be used by an external device to signal that it
need to be serviced.
 Logic 1 at INTR represents an active interrupt request. When an interrupt request

has been recognized by the 8086, it indicates this fact to external circuit with pulse to
logic 0 at the INTA output.
 The TEST input is also related to the external interrupt interface. Execution of a
WAIT instruction causes the 8086 to check the logic level at the TEST input.
 If the logic 1 is found, the MPU suspend operation and goes into the idle state. The
8086 no longer executes instructions; instead it repeatedly checks the logic level of
the TEST input waiting for its transition back to logic 0.
 As TEST switches to 0, execution resume with the next instruction in the program.
This feature can be used to synchronize the operation of the 8086 to an event in
external hardware.
 There are two more inputs in the interrupt interface: the nonmaskable interrupt NMI
and the reset interrupt RESET.
 On the 0-to-1 transition of NMI control is passed to a nonmaskable interrupt

service routine. The RESET input is used to provide a hardware reset for the 8086.
Switching RESET to logic 0 initializes the internal register of the 8086 and initiates a
reset service routine.
DMA Interface signals:
 The direct memory access DMA interface of the 8086 minimum mode consist of
the HOLD and HLDA signals.
 When an external device wants to take control of the system bus, it signals to the 8086
by switching HOLD to the logic 1 level. At the completion of the current bus cycle, the
8086 enters the hold state. In the hold state, signal lines AD0 through AD15, A16/S3
through A19/S6, BHE, M/IO, DT/R, RD, WR, DEN and INTR are all in the high Z
state.
 The 8086 signals external device that it is in this state by switching its HLDA output
to logic 1 level.
Maximum Mode
Interface
 When the 8086 is set for the maximum-mode configuration, it provides signals for
implementing a multiprocessor / coprocessor system environment.
 By multiprocessor environment we mean that one microprocessor exists in the

system and that each processor is executing its own program.
 Usually in this type of system environment, there are some system resources that
are common to all processors. They are called as global resources. There are also
other resources that are assigned to specific processors. These are known as local or
private resources.
 Coprocessor also means that there is a second processor in the system. In these
two processors does not access the bus at the same time. One passes the control of the
system bus to the other and then may suspend its operation.
 In the maximum-mode 8086 system, facilities are provided for implementing

allocation of global resources and passing bus control to other microprocessor or
coprocessor.
8288 Bus Controller – Bus Command and Control Signals:
 8086 does not directly provide all the signals that are required to control the memory, I/O
and interrupt interfaces.
 Specially the WR, M/IO, DT/R, DEN, ALE and INTA, signals are no longer produced by
the 8086. Instead it outputs three status signals S0, S1, S2 prior to the initiation of each
bus cycle. This 3- bit bus status code identifies which type of bus cycle is to follow.
 S2S1S0 are input to the external bus controller device, the bus controller generates the
appropriately timed command and control signals.
 The 8288 produces one or two of these eight command signals for each bus cycles. For
instance, when the 8086 outputs the code S2S1S0 equals 001; it indicates that an I/O read
cycle is to be performed.
 In the code 111 is output by the 8086, it is signaling that no bus activity is to take place.
 The control outputs produced by the 8288 are DEN, DT/R and ALE. These 3
signals provide the same functions as those described for the minimum system mode.
 This set of bus commands and control signals is compatible with the Multibus
and industry standard for interfacing microprocessor systems.
 The output of 8289 are bus arbitration signals:
Bus busy (BUSY), common bus request (CBRQ), bus priority out (BPRO), bus priority
in (BPRN), bus request (BREQ) and bus clock (BCLK).
 They correspond to the bus exchange signals of the Multibus and are used to lock
other processor off the system bus during the execution of an instruction by the 8086.
 In this way the processor can be assured of uninterrupted access to common

system resources such as global memory.
 Queue Status Signals: Two new signals that are produced by the 8086 in the
maximum- mode system are queue status outputs QS0 and QS1. Together they form
a 2-bit queue status code, QS1QS0.
 Following table shows the four different queue status.
 Local Bus Control Signal – Request / Grant Signals: In a maximum mode

configuration, the minimum mode HOLD, HLDA interface is also changed
QS1 QS0 Queue Status

0 (Low) 0 Queue Empty. The queue has been reinitiated as a
result of the execution of a transfer instruction.
0 1 First Byte. The byte taken from the queue was the
first byte of the instruction.
1 0 Queue Empty. The queue has been reinitiated as a
result of the execution of a transfer instruction.
1 1 (High) Subsequent Byte. The byte taken from the queue
was the subsequent byte of the instruction.
 . These two are replaced by request/grant lines RQ/ GT0 and RQ/ GT1,
respectively. They provide a prioritized bus access mechanism for accessing the local
bus.
Interrupts
Definition: The meaning of ‘interrupts’ is to break the sequence of operation. While the CPU
is executing a program, on ‘interrupt’ breaks the normal sequence of execution of
instructions, diverts its execution to some other program called Interrupt Service Routine
(ISR).After executing ISR , the control is transferred back again to the main program.
Interrupt processing is an alternative to polling.
Need for Interrupt: Interrupts are particularly useful when interfacing I/O devices that
provide or require data at relatively low data transfer rate.
Types of Interrupts: There are two types of Interrupts in 8086. They

are: (i)Hardware Interrupts and
(ii)Software Interrupts
(i) Hardware Interrupts (External Interrupts). The Intel microprocessors support

hardware interrupts through:
 Two pins that allow interrupt requests, INTR and NMI
 One pin that acknowledges, INTA, the interrupt requested on

INTR. INTR and NMI
 INTR is a maskable hardware interrupt. The interrupt can be enabled/disabled
using STI/CLI instructions or using more complicated method of updating the FLAGS
register with the help of the POPF instruction.
 When an interrupt occurs, the processor stores FLAGS register into stack, disables
further interrupts, fetches from the bus one byte representing interrupt type, and jumps
to interrupt processing routine address of which is stored in location 4 * <interrupt
type>. Interrupt processing routine should return with the IRET instruction.
 NMI is a non-maskable interrupt. Interrupt is processed in the same way as the

INTR interrupt. Interrupt type of the NMI is 2, i.e. the address of the NMI processing
routine is stored in location 0008h. This interrupt has higher priority than the maskable
interrupt.
 – Ex: NMI, INTR.
(ii) Software Interrupts (Internal Interrupts and Instructions) .Software interrupts can be
caused by:
 INT instruction - breakpoint interrupt. This is a type 3 interrupt.
 INT <interrupt number> instruction - any one interrupt from available 256 interrupts.
 INTO instruction - interrupt on overflow
 Single-step interrupt - generated if the TF flag is set. This is a type 1 interrupt. When
the CPU processes this interrupt it clears TF flag before calling the interrupt
processing routine.
 Processor exceptions: Divide Error (Type 0), Unused Opcode (type 6) and Escape
opcode (type 7).
 Software interrupt processing is the same as for the hardware interrupts.
 - Ex: INT n (Software Instructions)
 Control is provided through:
o IF and TF flag bits
o IRET and IRETD
Performance of Software Interrupts
1. It decrements SP by 2 and pushes the flag register on the stack.

2. Disables INTR by clearing the IF.
3. It resets the TF in the flag Register.
5. It decrements SP by 2 and pushes CS on the stack.
6. It decrements SP by 2 and pushes IP on the stack.
6. Fetch the ISR address from the interrupt vector table.
Interrupt Vector Table
Functions associated with INT00 to INT04
INT 00 (divide error)
 INT00 is invoked by the microprocessor whenever there is an attempt to divide a

number by zero.
 ISR is responsible for displaying the message “Divide Error” on the screen
INT 01
 For single stepping the trap flag must be 1
 After execution of each instruction, 8086 automatically jumps to 00004H to fetch 4

bytes for CS: IP of the ISR.
 The job of ISR is to dump the registers on to the screen
INT 02 (Non maskable Interrupt)
 When ever NMI pin of the 8086 is activated by a high signal (5v), the CPU Jumps
to physical memory location 00008 to fetch CS:IP of the ISR associated with NMI.
INT 03 (break point)
 A break point is used to examine the CPU and memory after the execution of a group
of Instructions.
 It is one byte instruction whereas other instructions of the form “INT nn” are 2
byte instructions.
INT 04 (Signed number overflow)
 There is an instruction associated with this INT 0 (interrupt on overflow).
 If INT 0 is placed after a signed number arithmetic as IMUL or ADD the CPU
will activate INT 04 if 0F = 1.
 In case where 0F = 0, the INT 0 is not executed but is bypassed and acts as a NOP.
Performance of Hardware Interrupts
 NMI : Non maskable interrupts - TYPE 2 Interrupt
 INTR : Interrupt request - Between 20H and FFH
Interrupt Priority Structure

Microprocessors and Interfacing Devices - Unit-1

Uploaded by

Microprocessors and Interfacing Devices - Unit-1

Uploaded by

Smartzworld.com Smartworld.

III B. Tech II semester

ELECTRICAL AND ELECTRONICS ENGINEERING

MICROPROCESSORS AND INTERFACING DEVICES

The Central Processing Unit (CPU):

Internal Architecture of 8085:

8085 Bus Structure: Address Bus:

The bit position for the flags in flag register is,

1. Sign Flag (S):

2. Zero Flag (z):

5. Carry Flag (CY):

Interrupt Control Unit:

Pin Diagram and Pin Description Of 8085

1. Power supply and clock frequency signals

 Vcc + 5 volt power supply

6. Interrupts and externally initiated operations:

 On receipt of an interrupt, the microprocessor acknowledges the interrupt by the active

Reset In (input, active low)

8. Single Bit Serial I/O ports:

 SID (input) - Serial input data line

Index or Pointer Registers

Code segment (CS) is a 16-bit register containing address of 64 KB segment with

Other registers of 8086

Control Flags: There are three control flags

Architecture of 8086 or Functional Block diagram of 8086

 EU executes instructions from the instruction system byte queue.

Figure: 8086 Architecture

 Specifically it has the following functions:

 When the EU executes a branch or jump instruction, it transfers control to a location

General Bus Operation

 In a minimum mode 8086 system, the microprocessor 8086 is operated in minimum

 There is a single microprocessor in the minimum mode system.

Pin Diagram of 8086 and Pin description of 8086

 The 8086 operates in single processor or multiprocessor configuration to achieve high

mode) and other function in maximum mode configuration (multiprocessor mode).

 The 8086 signals can be categorized in three groups.

 The following signal descriptions are common for both modes.

o During I/O operations, these lines are low.

Figure shows the Pin functions of 8086.

 M/IO – Memory/IO: This is a status line logically equivalent to S2 in maximum mode.

Minimum Mode 8086 System

Minimum mode 8086 system

 In a minimum mode 8086 system, the microprocessor 8086 is operated in minimum

 They are controlled by two signals namely, DEN and DT/R.

Write Cycle Timing Diagram for Minimum Mode

Maximum Mode 8086 System

Memory Read Timing Diagram in Maximum Mode of 8086

Memory Write Timing in Maximum mode of 8086

RQ/GT Timings in Maximum Mode

Minimum Mode Interface

Each and every group is explained clearly.

 Logic 1 at INTR represents an active interrupt request. When an interrupt request

 On the 0-to-1 transition of NMI control is passed to a nonmaskable interrupt

DMA Interface signals:

 By multiprocessor environment we mean that one microprocessor exists in the

 In the maximum-mode 8086 system, facilities are provided for implementing

8288 Bus Controller – Bus Command and Control Signals:

 The output of 8289 are bus arbitration signals:

 In this way the processor can be assured of uninterrupted access to common

 Following table shows the four different queue status.

 Local Bus Control Signal – Request / Grant Signals: In a maximum mode

QS1 QS0 Queue Status

Types of Interrupts: There are two types of Interrupts in 8086. They

(i) Hardware Interrupts (External Interrupts). The Intel microprocessors support

 Two pins that allow interrupt requests, INTR and NMI

 One pin that acknowledges, INTA, the interrupt requested on

 NMI is a non-maskable interrupt. Interrupt is processed in the same way as the

 – Ex: NMI, INTR.

 INT instruction - breakpoint interrupt. This is a type 3 interrupt.

 INTO instruction - interrupt on overflow

 Software interrupt processing is the same as for the hardware interrupts.

 - Ex: INT n (Software Instructions)

 Control is provided through:

o IF and TF flag bits

o IRET and IRETD