Cufsm Introduction

CUFSM2.
Introductory Questions
• CUFSM?
– What is CUFSM?
– What are the system requirements?
– Why would I use CUFSM?
– Why do 2 versions of CUFSM exist?
– Why would I use the Matlab version?
– CUFSM is free?
• Finite Strip?
– What is Finite Strip?
– What is a buckling curve?
– What is a buckling mode?
– What is the half-wavelength?
– What is the load factor?
– What are Mcr and Pcr?
– How can I use finite strip results in design?
What is CUFSM?
• Software for exploring elastic buckling behavior.
• CUFSM calculates the buckling stress and
buckling mode of arbitrarily shaped, simply
supported, thin-walled members.
• CUFSM was originally written to support
research on the behavior and design of cold-
formed steel members with a variety of different
types of longitudinal stiffeners.
• CUFSM is freely available and distributed.
What are the system requirements?
• For the standalone version a PC with any flavor* of
Windows is required
• For the Matlab version, any machine with Matlab v6 will
work - this means most flavors of Unix and all PCs are
supported - but not Macs* at this time.
• The faster your machine the faster your analysis will
run, but finite strip is an efficient solution to a
complicated problem, and typical analyses, on even
older 486 or Pentium machines, take less than a minute
to complete.
* (version 2.5 has not been tested on Windows XP at this time) .
**(Rumors are that Matlab will be ported to OS X, then CUFSM will run on a Mac.)
Why would I use CUFSM?
• To explore and better understand elastic buckling
behavior of thin-walled members.
• To accurately determine the elastic buckling stress of a
thin-walled section of arbitrary cross-section.
• Design and hand methods that are traditionally used for
“plate” structures often ignore compatibility at plate
junctures and typically provide no means to calculate a
variety of important buckling modes (e.g., distortional
buckling). CUFSM allows all elastic buckling modes of a
structure to be quantified and examined.
• To determine inputs such as Pcr and Mcr for the Direct
Strength Method of design.
Why do 2 versions of CUFSM exist?
• The standalone version is for those users who do not
have Matlab and only require access to the available
features in the graphical version of CUFSM.
• The Matlab version of CUFSM is for all users who have
Matlab available. CUFSM was originally coded in
Matlab and thus using CUFSM in Matlab provides
greater flexibility.
• Matlab exists on platforms other than Windows PCs
(including Linux) and thus the Matlab version of CUFSM
runs on many more platforms than the PC standalone
version.
Why would I use the Matlab version?
• The Matlab version allows you to directly access and
modify the source code itself.
• Parameter studies may be easily completed using the
CUFSM subroutines from within your own Matlab
program (see Advanced Functions - Matlab).
• Matlab is available on many more platforms and allows
you to use CUFSM on high-powered workstations and
other machines (e.g., Linux).
• Far more flexibility is available with the Matlab version
since any subroutine, from the graphics, to the actual
computations may be separately accessed.
CUFSM is free?
• Yes.
• CUFSM is distributed as FREEWARE.
• If you use CUFSM in design work or in scientific
studies I ask that you please provide a reference
to my work and cite the version of CUFSM you
are using for the work.
• Standard disclaimers apply: Although all attempts have
been made to insure CUFSM is reliable, the responsibility for use
of the program rests solely on the user.
What is Finite Strip?
• Finite strip is a specialized version of the finite element method.
finite element finite strip
• In the finite strip method, element shape functions use polynomials in the
transverse direction, but trigonometric functions in the longitudinal direction.
Judicious choice of the longitudinal shape function allows a single element, a
“strip” to be used.
• Classical finite strip, as implemented in CUFSM, uses a single half sine wave
(sin(πx/a)) for the longitudinal direction. See Appendix (1) Theory for more
details on the finite strip method.
What is a buckling curve?
• The tutorials and later examples cover this in detail, but for now,
the buckling curve is the primary result from a finite strip
analysis. A typical buckling curve is shown below. The minima of
this curve are of special interest as the indicate the critical half-
wavelength and load factor for a given buckling mode.
What is a buckling mode?
• The buckling mode is the shape
that a member buckles into, for
2D representation of the local
example shown here is the local buckling mode shape (only the
buckling mode of a Zee in bending. undeformed and the maximum
deformed cross-sections are shown)
More precisely, a buckling mode for a Zee in pure bending.
represents a secondary deformed
shape that has the same potential
energy as the primary deformation,
simple bending in this case.
3D representation of the local

buckling mode shape. Local buckling
occurs at short half-wavelengths
(repeats in short intervals) as shown
here.
applied load on a Zee
What is the half-wavelength?
• The finite strip method assumes longitudinal
deformation occurs in 1/2 a sine wave (a half-
wavelength)
• The half-wavelength is the length of the 1/2 sine wave
assumed in the analysis
• Analysis is performed for systematically increasing half-
wavelengths to determine the buckling behavior (mode
shape and load factor) of a member
• Note: half-wavelength is not strictly equal to the
unbraced length, as any identified mode may repeat
itself multiple times within a given unbraced length
What is the load factor?
• To perform finite strip analysis the member is loaded with a reference stress
distribution
• the load factor times the reference stress distribution is equal to the buckling
stress
• For example, consider a member with a stress distribution of 1.0 ksi at every
location (node) on the member. Assume that after analysis a local buckling
load factor of 15.4 is identified. What is the local buckling stress? The local
buckling stress is 1.0 ksi x 15.4 = 15.4 ksi
• For another example, consider a member that is loaded with a reference
stress distribution that is equal to the moment that causes first yield in a
member, My. Assume after analysis a distortional buckling load factor of 0.5 is
identified. This implies that distortional buckling occurs at 0.5My. If first yield is
in compression, and the yield stress is denoted, fy, then the distortional
buckling stress is 0.5fy.
• More precisely: the load factor is the eigenvalue of the relevant eigenvalue
buckling problem, and the buckling mode is the eigenvector.
How can I use CUFSM results in design?
• Use the Direct Strength Method
• The Direct Strength Method requires that you
know the elastic buckling load (Pcr) or elastic
buckling moment (Mcr) for your member. CUFSM
provides a means to calculate these values for
any arbitrary cross-section.
• Most design codes for thin-walled structures rely
on simplified plate buckling coefficients, or “k”
values - CUFSM may be used to determine far
more accurate “k” values than used in design.
CUFSM2.5
What are Mcr and Pcr?

• They are the elastic buckling moment and the elastic
buckling load.
• They are inputs in the Direct Strength Method.
• For typical open thin-walled shapes, such as cold-
formed steel Cees, Zees or hats, three critical
loads/moments exist
– Pcrl/Mcrl: Elastic critical local buckling load/moment
– Pcrd/Mcrd: Elastic critical distortional buckling load/moment
– Pcre/Mcre: Elastic critical Euler buckling load/moment
• Multiple modes (e.g. flexural, torsional, and flexural-
torsional may exist for Pcre).

Cufsm Introduction

Uploaded by

Cufsm Introduction

Uploaded by

CUFSM2.

finite element finite strip

3D representation of the local

What are Mcr and Pcr?

You might also like