What Is Keyphasor

What is Keyphasor® and Why install a
Keyphasor® transducer?
"
Vibration monitoring and diagnostics systems have three purposes. First, the system
should alert Operators to developing problems, while they are still manageable.
Second, to minimize damage to the machine, the system should provide shutdown
capability in the event of a catastrophic failure. Third, and perhaps most important, it
should provide information to help the Machinery Specialist quickly and accurately
diagnose machinery conditions.
The Keyphasor® transducer is

an essential element of a
monitoring and diagnostics
system because it provides
both the Operator and
Machinery Specialist with
information vital to the
successful protection and
management of plant
machinery. The Keyphasor®
signal, (Figures 2 and 3) a
once-per-turn voltage pulse
provided by a transducer
(normally a proximity probe), is
used by the monitoring system
to generate filtered vibration
amplitude and phase lag
measurements. The
Keyphasor® information can help the Operator identify developing machine problems
or distinguish serious problems from less serious ones.
Information for the Operator
In the past, Operators were only required to
manage the process. In today’s competitive
environment, they are expected to manage
not only the process, but plant assets,
including machinery. In some plants, the
Operator can call a Machinery Specialist to
analyze machinery data and determine what
should be done. However, in many plants, a
specialist may not be immediately available. If
the Operator only has direct (or overall)
vibration amplitude measurements, it is
difficult to decide whether the machinery
problem is serious or not.
A permanently-installed Keyphasor® transducer provides the Operator with phase

information which can help him detect subtle changes to the machinery. Operators can
use the Bently Nevada 3500 Machinery Data Management System, the Trendmaster®
2000 System or the Data Manager® 2000 System for Windows NT TM to generate
industry-standard plots that display 1X (synchronous) amplitude and phase or NOT 1X
(nonsynchronous) amplitude measurements. These Bently Nevada systems were
designed to present 1X and NOT 1X information in a way that is easy for Operators to
measure. Operators can easily compare the 1X portion of the vibration signal to the
NOT 1X portion.
Changes in 1X vibration need to be analyzed. If the change is gradual, the Operator

can schedule a visit by the Machinery Specialist. Then, the operator can continue to
manage his machinery and process with increased attention. If the change is sudden,
an immediate call to the specialist is in order, and the Operator can apply the
appropriate management procedure to this new situation.
Serious machine problems

A change in the NOT 1X portion of the overall vibration, however, is often a strong
indicator of malfunctions that can quickly be detrimental to the machine. If there has
been an increase in NOT 1X vibration, a Machinery Specialist should be called
immediately. Some of the most common causes of NOT 1X vibration are fluid-induced
instabilities, rotor-to-stator rubs, and gear faults. All are of immediate concern.
Information for the Machinery Specialist
The Machinery Specialist also needs
machinery information from a Keyphasor®
transducer to perform his job properly.
Although some plot formats, such as shaft
orbits and spectrum displays, will be available,
a Keyphasor® mark on orbit plots (Figure 1) is
necessary to evaluate phase lag. Without the
Keyphasor® mark, the shaft orbit will not
indicate if the vibration is occurring in a
synchronous (1X) or nonsynchronous mode. A
Keyphasor® mark is also necessary to determine the direction of shaft vibration
precession (in the same or the opposite direction of shaft rotation) from the orbit, and to
generate the mode shape of the shaft (Figure 4).
In addition,
polar and
Bode plots,
which are
necessary to
document
rotor response
on startup or
shutdown,
cannot be developed without Keyphasor® information. These plots are also needed for
accurate balancing. Before any balancing solutions are attempted, polar plots should
be reviewed to verify where the weights should be placed.
The Machinery Specialist needs to review as much machinery data as possible to

provide an accurate analysis. The lack of Keyphasor®-related data can lead to an
incorrect diagnosis.
It is sometimes difficult to install a Keyphasor® transducer. However, the additional

information provided by the Keyphasor® signal is absolutely necessary for Operators
and Machinery Specialists to successfully protect and manage machinery. For this
reason, both the American Petroleum Institute and Bently Nevada, in its specifications
for machinery protection systems, recommend installing a Keyphasor® transducer and
a redundant Keyphasor® transducer.

What Is Keyphasor

Uploaded by

What Is Keyphasor

Uploaded by

What is Keyphasor® and Why install a

The Keyphasor® transducer is

A permanently-installed Keyphasor® transducer provides the Operator with phase

Changes in 1X vibration need to be analyzed. If the change is gradual, the Operator

Serious machine problems

The Machinery Specialist needs to review as much machinery data as possible to

It is sometimes difficult to install a Keyphasor® transducer. However, the additional

You might also like