Ashida Adr

ASHIDA Numerical Single Pole Type: ADR111A
B Protection Relay
ADR211A (Communicable)
(ADITYA Series)
(Preliminary)
Features:
• Single Element (Phase/EF) Over
current IDMT with instant trip.
• Back - lit LCD display for
settings.
• Display of fault current. / Load
current.
• Selection of Curve: Six
selectable curves (Normal
Inverse1 (C1), Normal Inverse2
(C2), Very Inverse (C3),
Extremely Inverse (C4), Long
Time Inverse (C5) & Definite
Time (C6).
• Design using DSP technology.
• Latching of fault current up-to last
5 fault
• Password protection for setting.
• Site selectable CT secondary
• Relay can be made ether IDMT or Define time
• Programmable operating time in instantaneous element
• Breaker Fail & Trip Circuit Supervision Function
• Programmable Annunciation Contact
• RS 232 (at front) and RS 485 (at rear side) Communication Port for remote SCADA (only for
ADR211A i.e. communicable Relay).
General:
The ADR111A is member of Ashida Numerical Relay family (Aditya Series) design to meet demand of
low and medium switchgear control. The ADR111A is a Single Pole Protection relay with Instantaneous
high set and programmable output to simplify feeder protection wiring. The ADR111A continuously
monitors phase current, through CT connections. The high-speed micro-controller samples this current
through a 12-bit A/D converter. The micro-controller performs powerful Digital Algorithms to find out
Amplitude of current signal, and then this value is use for protection and metering function. All
measurement is tuned to fundamental frequency. Each input current is also displayed on 16 x 2 LCD
display for metering. The Relay is having main three functions 1) Protection 2) Self-Supervision 3)
Measurement
The Relay can be supplied with different model. It can be either Definite Time or IDMT.
Note: Due to our policy to upgrade our products constantly, we reserve the right to supply products which may vary
slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

Plot No. A-308, Road No. 21,
Wagle Industrial Estate, Ref.: ADR111A_AM10101
Thane (W)-400 604. INDIA. Issue: 04 01.08.10
E-mail: sales@ashidaelectronics.com
Web: www.ashidaelectronics.com Page 1 /6
Type: ADR111A
(ADITYA Series)
(Preliminary)
1. Protection Functions:
The ADR111A give maximum benefit/cost ratio. The ADR111A give all the advantage of numerical relay
at affordable cost. Following is summery of different protection functions provided by relay.
1.1 Over current protection:

The ADR111A has Single sensing element. The tripping current can be set from 10% to 250% in steps
of 1% by Keys switch provided on front panel. The unit has got selection of IDMT characteristic of
international IEC standard Very inverse / Extremely Inverse / Long Inverse and Standard inverse (both
3.0 sec and 1.3sec at 10 times). The unit also has Time Multiplier Setting (TMS) from x0.01 to x1.0 for
IDMT delay multiplication. The instantaneous tripping function is having range of 50% - 3000% and can
be set in steps of 50%. The high speeds CPU continuously monitor the all four current inputs and
compare with IDMT as well as instantaneous setting. If any one current is above instantaneous setting
the relay provides immediate trip command bypassing IDMT delay. If is input current is less than
instantaneous setting but more than IDMT setting, CPU calculate IDMT delay as per selected IDMT
characteristic multiply it with TMS setting and provide trip command if fault is persist even after this time
delay.
All the settings are password protected to prevent unauthorised change.
1.2 Extra Alarm Contact:

Any Protection panel required extra contacts for provide visual ALARM and ANNUNCIATION indication
for operator. Also some status contacts for SCADA or remote indications. Usually separate
electromechanical relay used for contact multiplication of protection relay contacts. This added extra
wiring and extra hardware. The ADR111A provide separate programmable ALARM contact for such
application. Maximum 2 nos. of extra contacts can be provided. These contacts can be programmed as
follows
ANN. TYPE 1 ANN. TYPE 2
RELAY 1 HF COM. ALARM

RELAY 2 IDMT COM. ALARM
2. Supervision Function:
2.1 Self-supervision:
The continuously keeping track on its internal hardware and the movement it detect any failure of any
component, it give message on LCD display, This feature is very useful to give pre information to avoid
any mall - operation. In such situation it use some default setting and remain in protection mode.
3. Measurement Function:
In normal condition this display shows all settings. Via keyboard the display can be program to show the
actual current flowing through the relay. If current excesses set value the relay gives trip command. The
type of fault is displayed on LCD display. During the fault condition the relay measure the fault
current and store in non-volatile memory. The fault current can be read via keyboard on LCD
display Last 5 fault values along with tripping counter can be view via key-board. All settings are
save in electrically erasable read only memory and remain.

Type: ADR111A
(ADITYA Series)
(Preliminary)
4. Breaker Fail Function (BF or LBB)
Normally after tripping current should be come Zero with in 100 – 200ms time depend upon type of fault
and breaker mechanism. After Fault Relay start one internal timer (settable from 0.1s to 0.8 s) If fault is
not cleared during this time then relay declare as Breaker fail (LBB function)
5. Status :
Status input S1 and S2 are general purpose for SCADA application and S3 and S4 are dedicated for CB
NC and NO used for trip circuit supervision.
Ordering Information:
The relay is available with nos. of different option. The option is specified by model no. It is user
responsibility to specify correct model no. while ordering.
While Or d e ring Spe cify t he fo llow ing Info rm at io n for A DR11 1A Re la y
Definition of Model No of Aditya Se rie s of Relays
AM XX X– XX – X – X – X X – X
Reserved for Future Use
Auxiliary Supply
01 = 18 – 52 V dc
PT Secondary
0 02 = 77 – 250 V dc
03 = 110 VAC
04 = 230 VAC
05 = 60 V dc
CT Secondary
1 = 1 Amp. 06 = 18 - 250 V dc
2 = 5 Amp.
3 = 1 Amp. / 5 Amp. Selectable
AM XXX XX X
Single Pole Relay
101 01 Relay with site selectable CTs, Trip circuit supervision CSA – 150 3
and breaker fail function. 2 extra Ann. Contacts and 4
optically isolated status inputs ( 2nos for TCS )
O rd e ri n g i n f o r m a t i o n :
A D R 1 1 1 A - A M - X X X - X X - X - X - X X - X
E xa m p l e
ADR 1 1 1 A – AM - 1 0 1 -0 1 -3 - 0 -2 - 0
T yp e : A D R1 1 1 A
B a c k Te r m i n a l L a y o u t : With 2 Programmable extra contacts, Selectable CT TCS Logic.
C a b i n e t Ty p e : C SA - 1 5 0 n o n D r a w o u t
A u xi l i a r y S u p p l y : 7 7 -2 5 0 V d c
C T s e c : 1 / 5 Amp.

Type: ADR111A
(ADITYA Series)
(Preliminary)
Technical Specifications:
Sr. No. Specification Particulars
I. For Model AM101xx
Inputs : Model Suitable for CT secondary 1.0 Amp or 5.0 Amp.
AM10101xxxxx (Selectable)
Protection Relay Setting : Setting For IDMT 10% - 250 % In steps of 1%
Range : Operating Time Normal Inverse 1 (C1)
Normal Inverse 2 (C2)
Very Inverse (C3)
Extremely Inverse (C4)
Long Time Inverse (C5)
Definite Tme (C6) 00(Inst) – 99.9Sec
: Inst. Setting For HF 50% - 3000%. or bypass In steps of 50%
: Inst Operating Time Inst = < 30ms and additional adjustable software
delay of 00 – 2.0Sec in steps of 10ms.
Output contacts : Model 1) 2 NO Trip duty contact for Alarm and Trip
AM10101xxxxx 2) 2 NO ANN. Duty contacts ( Programmable)
II. Pickup Current : Within 1.1 times of set current value.
III. Resetting Current : 90% of set value.
IV. Time Accuracy : Within class 2.5 As per IS: 3231.
V. Burden on CTs : Less than 0.2VA.
VI. Aux. Supply : 18 – 52VDC or 77 – 250VDC. To be specified while ordering.
VII. Burden on Aux. Supply : Less than 10VA on any supply.
VIII. Contact Rating Trip Duty : Make and carry for 3sec. – 7500VA with max. 30A & 660VAC/DC
: Make and carry for continuous – 1250VA with max. 5A & 660VAC/DC
: Break AC – 1250 VA DC – 100 W resistive 50W inductive.
IX. Operational Indicators (Flags)
ON / Error : Green LED indicates Relay OK
: Red LED indicates Problem in relay Hardware.
PKP : Red LED’s indicates the Over Current relay Pickup.
FAULT : Red LED’s indicates the Over Current relay trip, Hand Reset (HR) Type.
TRIP : Indicates that Trip pulse is being executed. When BYPASS P.B. is
pressed, actual trip is not executed.
X. Thermal Withstand Capacity : X40 times the normal current for 3sec.
: x2 Continuous
XI. High Voltage Test : IEC 60255-5
: Except DC Voltage – 2.0 kV (RMS), 50Hz
: Only DC voltage - 2.8 kV DC
: Between Open contact of TRIP / CLOSE 1.5kV (RSM) 50Hz
: Between Open contact of ALARM – 1kV (RSM) 50Hz

Type: ADR111A
(ADITYA Series)
(Preliminary)
XII. Impulse Voltage Test (all : IEC60255-5

circuit class – III) : 5kV (peak) 1.2 / 50us, 0.5 J, 3 positive and 3 negative impulse at interval
of 5 sec
XIII. High Frequency test : IEC 60255-22-1, Class III
: 2.5 kV (peak) 1MHz , τ = 15µs 400 surges / s duration 2 s
XIV. Electro static Discharge : IEC 60255-22-2 Class III and IEC 61000-4-2 class III
: 4kV/6kV contact discharge, 8kV air discharge, both polarities 150pF, Ri
330 Ω
XV. Irradiation with radio : IEC 60255-22-3 and IEC 61000-4-2 class III
frequency field, pulse- : 10V/m; 80 to 1000MHz; 80%; 1kHz AM
modulated,
XVI. Fast transient : IEC 60255-22-3 and IEC 61000-4-3, class III
interference/bursts : 4kV; 5/50ns; 5kHz burst duration = 15ms;
: Repetition rate 300ms; Both polarities; Ri = 50Ω; duration 1 min.
XVII. Shock Test : IEC 60255-21-2 class 1
: Semi-Sinusoidal
: 5g acceleration, duration 11ms,
: Each 3 shocks in both direction of the 3 axes
XVIII. Vibration Test : IEC 60255-21-1 class 1 / IEC 60068-2-6
: Sinusoidal 10 to 60Hz ±0.035 mm
: Amplitude, 60 to 150Hz, 0.5g acceleration
: Sweep rate 1 octave/min; 20 cycle in 3 orthogonal
XIX. Seismic Test : IEC 60255-21-3
: In single axis sine sweep in X-axis
01- sweep (@a sweep rate of 1 octave/minute) vibration in the
frequency range (5-40 Hz) at amplitude of 3.5mm or 1.0gn
(whichever is less)
: In single axis sine sweep in Y-axis
01- - weep (@a sweep rate of 1 octave/minute) vibration in the
frequency range (5-40 Hz) at amplitude of 1.5mm or 0.5gn
(whichever is less)
XX. Bump Test : IEC 60255-21-2 Class-1
: 1000 bumps of 10gn peak acceleration and 16ms pulse duration in each
of the two opposite direction per axis as per IEC60255-21-2 class 1 No.
of axes . 3.
XXI. Shock Withstand : IEC 60255-21-2 Clas-1
: 3 shocks of 15gn peak acceleration and 11ms pulse in each of two
opposite direction. No. of axis : 3
XXII. Shock Response Test : IEC 60255-21-2 Clas-1
: 3 shocks of 1gn peak acceleration and 11ms pulse in each of two
opposite direction. No. of axis : 3

Type: ADR111A
(ADITYA Series)
(Preliminary)
XXIII. Vibration Endurance Test : IEC60255-21-1

20-sweeps (@ a sweep rate of 1octave / minutes) vibration in the
frequency range (10-150Hz) at 1 gn (9,8m/s2) acceleration in each of the
3 mutually perpendicular axes
XXIV. Environmental withstand : IEC60068-2
(cold, Dry heat & steady state Cold – 2 hours operational condition at –(40 +/- 3) deg C as per
Damp Heat) IEC60068-2-1
Dry – 2 Hours dry heat operational condition at(55+/2 2 deg. C as per
IEC60068-2-2
Steady state damp heat - 2 hours steady sate damp heat operational
condition at temperature at (55 +/- 2) deg. C & humidity 95% RH as per
IEC60068-2-78
XXV. Drawing References : For Cabinet Type CSA -150 - MAC00101
: For Operating C1 - APR02201
Characteristics
C2 - APR01801
C3 - APR05101
C4 - APR05201
C5 - APR05301
: For Electrical AM10101 - APR06804_2
Connection
• Datasheet Change Log for ADR111A

Issue No. Date Description /Changes
(Revision)
01 28.08.09 Original Revision
02 09.12.09 Settings Changed
03 26.12.09 Common Model no. Defined For Phase & EF
04 01.08.10 Photo and terminal arrangement changed.


Ashida Adr

Uploaded by

Ashida Adr

Uploaded by

ASHIDA Numerical Single Pole Type: ADR111A

ASHIDA ELECTRONICS PVT LTD.

1.1 Over current protection:

1.2 Extra Alarm Contact:

RELAY 1 HF COM. ALARM

ASHIDA ELECTRONICS PVT LTD.

ASHIDA ELECTRONICS PVT LTD.

ASHIDA ELECTRONICS PVT LTD.

XII. Impulse Voltage Test (all : IEC60255-5

ASHIDA ELECTRONICS PVT LTD.

XXIII. Vibration Endurance Test : IEC60255-21-1

• Datasheet Change Log for ADR111A

ASHIDA ELECTRONICS PVT LTD.

You might also like