Arduino To Bread Board

From Arduino to a Microcontroller on a Breadboard
This tutorial explains how to migrate from an Arduino board to a standalone microcontroller on a breadboard. It's
similar to this tutorial, but uses an Arduino board to program the ATmega on the breadboard.
Unless you choose to use the minimal configuration described at the end of this tutorial, you'll need four components
(besides the Arduino, ATmega328, and breadboard):
- a 16 MHz crystal,
- a 10k resistor, and
- two 18 to 22 picofarad (ceramic) capacitors.
Burning the Bootloader

If you have a new ATmega328 (or ATmega168), you'll need to burn the
bootloader onto it. You can do this using an Arduino board as an in-system
program (ISP). If the microcontroller already has the bootloader on it (e.g.
because you took it out of an Arduino board or ordered an already-bootloaded
PDF generated automatically by the HTML to PDF API of PDFmyURL

ATmega), you can skip this section.
To burn the bootloader, follow these steps:
1. Upload the ArduinoISP sketch onto your Arduino board. (You'll need to select
the board and serial port from the Tools menu that correspond to your board.)
2. Wire up the Arduino board and microcontroller as shown in the diagram to the
right.
3. Select "Arduino Duemilanove or Nano w/ ATmega328" from the Tools > Board
menu. (Or "ATmega328 on a breadboard (8 MHz internal clock)" if using the
minimal configuration described below.)
4. Select "Arduino as ISP" from Tools > Programmer
5. Run Tools > Burn Bootloader
You should only need to burn the bootloader once. After you've done so, you
can remove the jumper wires connected to pins 10, 11, 12, and 13 of the Arduino
board.
Using an Arduino board to burn the

bootloader onto an ATmega on a breadboard.
Uploading Using an Arduino Board

Once your ATmega328p has the Arduino bootloader on it, you can upload programs to it using the USB-to-serial
convertor (FTDI chip) on an Arduino board. To do, you remove the microcontroller from the Arduino board so the FTDI
chip can talk to the microcontroller on the breadboard instead. The diagram at right shows how to connect the RX and
TX lines from the Arduino board to the ATmega on the breadboard. To program the microcontroller, select "Arduino
Duemilanove or Nano w/ ATmega328" from the the Tools > Board menu (or "ATmega328 on a breadboard (8 MHz
internal clock)" if you're using the minimal configuration described below). Then upload as usual.
Uploading sketches to an ATmega on a breadboard. Remember to remove the microcontroller from the Arduino board!
Minimal Circuit (Eliminating the External Clock)

If you don't have the extra 16 MHz crystal and 18-22 picofarad capacitors used in the above examples, you can configure
the ATmega328 to use its internal 8 MHz RC oscillator as a clock source instead. (You don't really need the 10K pullup
resistor on the reset pin either, so we remove it to get a truly minimal configuration.)
You'll need to install support for an additional hardware configuration:

1. Download this hardware configuration archive: breadboard-1-6-x.zip, Breadboard1-5-x.zip or Breadboard1-0-x.zip
depending on which IDE you use.
2. Create a "hardware" sub-folder in your Arduino sketchbook folder (whose location you can find in the Arduino
preferences dialog). If you've previously installed support for additional hardware configuration, you may already have a
"hardware" folder in your sketchbook.
3. Move the breadboard folder from the zip archive to the "hardware" folder of your Arduino sketchbook.
4. Restart the Arduino software.
5. You should see "ATmega328 on a breadboard (8 MHz internal clock)" in the Tools > Board menu.
Once you've done this, you can burn the bootloader and upload programs onto your ATmega328 as described above.
Be sure to select "ATmega328 on a breadboard (8 MHz internal clock)" when burning the bootloader. (If you select the
wrong item and configure the microcontroller to use an external clock, it won't work unless you connect one.)
Attention
This procedure works on Arduino 1.0.x software.

Uploading sketches to an ATmega on a
Using an Arduino board to burn the bootloader onto an ATmega on a breadboard.
breadboard (w/o an external clock).
Getting Rid of the Arduino Board

Once you've programmed the ATmega on the breadboard, you can eliminate the Arduino. To do so, you'll need to

provide an alternative power supply for the microcontroller. See the standalone Arduino on a breadboard tutorial for
details.
Share

Arduino To Bread Board

Uploaded by

Arduino To Bread Board

Uploaded by

From Arduino to a Microcontroller on a Breadboard

Burning the Bootloader

PDF generated automatically by the HTML to PDF API of PDFmyURL

To burn the bootloader, follow these steps:

Using an Arduino board to burn the

Uploading Using an Arduino Board

Minimal Circuit (Eliminating the External Clock)

You'll need to install support for an additional hardware configuration:

This procedure works on Arduino 1.0.x software.

PDF generated automatically by the HTML to PDF API of PDFmyURL

Getting Rid of the Arduino Board

PDF generated automatically by the HTML to PDF API of PDFmyURL

PDF generated automatically by the HTML to PDF API of PDFmyURL

You might also like