Lect 1 Introduction To Process Control
Uploaded by
Zaidoon MohsinLect 1 Introduction To Process Control
Uploaded by
Zaidoon MohsinIntroduction to process control
Temp.
indicator
Hot water
Water
Heater
Steam
Cool water
Figure (1) Open loop system
Figure (2) Manual Control system
Figure (3) Automatic Control system (Closed Loop)
Process Control /Lec. 1 1 Written by Assis. Prof.
Fourth Class Dr. Zaidoon M. Shakor
Control System Objectives
o Economic Incentive
o Safety
o Equipment Protection
o Reduce variability
o Increase efficiency
o Ensure the stability of a process
o Elimination of routine
Definitions:
System: It is a combination of components that act together and perform a certain
objective.
Plant: It is the machine of which a particular quantity or condition is to be controlled.
Process: Is defined as the changing or refining of raw materials that pass through or
remain in a liquid, gaseous, or slurry state to create end products.
Control: In process industries refers to the regulation of all aspects of the process.
Precise control of level, pH, oxygen, foam, nutrient, temperature, pressure and flow is
important in many process applications.
Sensor: A measuring instrument, the most common measurements are of flow (F),
temperature (T), pressure (P), level (L), pH and composition (A, for analyzer). The
sensor will detect the value of the measured variable as a function of time.
Set point: The value at which the controlled parameter is to be maintained.
Controller: A device which receives a measurement of the process variable,
compares with a set point representing the desired control point, and adjusts its output
to minimize the error between the measurement and the set point.
Error Signal: The signal resulting from the difference between the set point
reference signal and the process variable feedback signal in a controller.
Feedback Control: A type of control whereby the controller receives a feedback
signal representing the condition of the controlled process variable, compares it to the
set point, and adjusts the controller output accordingly.
Steady-State: The condition when all process properties are constant with time,
transient responses having died out.
Process Control /Lec. 1 2 Written by Assis. Prof.
Fourth Class Dr. Zaidoon M. Shakor
Transmitter: A device that converts a process measurement (pressure, flow, level,
temperature, etc.) into an electrical or pneumatic signal suitable for use by an
indicating or control system.
Controlled variable: Process output which is to be maintained at a desired value by
adjustment of a process input.
Manipulated variable: Process input which is adjusted to maintain the controlled
output at set point.
Disturbance: A process input (other than the manipulated parameter) which affects
the controlled parameter.
Process Time Constant( ): Amount of time counted from the moment the variable
starts to respond that it takes the process variable to reach 63.2% of its total change.
Block diagram: It is relationship between the input and the output of the system. It is
easier to visualize the control system in terms of a block diagram.
X(s) Transfer function Y(s)
Input G(s) Output
Block diagram
Transfer Function: it is the ratio of the Laplace transform of output (response
function) to the Laplace transform of the input (driving force) under assumption that
all initial conditions are zero unless that given another value.
e.g. the transfer function of the above block diagram is G (s) = Y(s)/X(s)
Closed-loop control system: It is a feedback control system which the output signals
has a direct effect upon the control action.
Heater
(Heating)
Temperature
Final control element
Transmitter
(Thermocouple)
Process Control /Lec. 1 3 Written by Assis. Prof.
Fourth Class Dr. Zaidoon M. Shakor
Advantage: more accurate than the open-loop control system.
Disadvantages: (1) Complex and expensive
(2) The stability is the major problem in closed-loop control system
Open-loop control system: It is a control system in which the output has no effect
upon the control action. (The output is neither measured nor fed back for comparison
with the input).
(Timer) Motor
Advantages:
(1) Simple construction and ease of maintenance.
(2) Less expensive than closed-loop control system.
(3) There is no stability problem.
Disadvantages:
(1) Disturbance and change in calibration cause errors; and output may be
different from what is desired.
(2) To maintain the required quality in the output, recalibration is necessary
from time to time
Note: any control system which operates on a time basis is open-loop control system,
e.g. washing machine, traffic light …etc.
Process Control /Lec. 1 4 Written by Assis. Prof.
Fourth Class Dr. Zaidoon M. Shakor
