DSP A11 Manual PDF

Beijing RuiZhitianhong technology Co.
LTD
BEIJING
RUIZHITIANHONG S&T Co.,Ltd

Engraving machine motion control system
A11-Three axis mechanical carving
User's manual
ADD.：Beijing haidian district shangdi three street jiahua building A308. P.C.：100085.
Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn

Beijing RuiZhitianhong technology Co.LTD
Thank you for choosing the products!
This manual helps you be familiar with the company's products, and get information about
systems’ components、configuration,etc.
This manual detailed knowledge of the system characteristics、operational processes、
installation and commissioning, and safety precautions.please read this manual carefully
before using the system and machine, which will help you make use it better.
Cautions：
1. Use of this product is strictly prohibited in the strong interference、 strong magnetic field
environment. Operating ambient temperature 0-70 ℃, working environment humidity
0-90% (non-condensing).
2. Insert U disk in the correct direction.Do not pull out 50-pin cable when system run.
3.Perform processing U disk file process, do not pull out the U disk to prevent the
interruption of data transmission.
4. Strictly prohibited metal, dust, and other conductive substances get into the controller.
5.The machine shell should connect the ground wire to ensure the safety of the work and
to prevent interference.
6. Prohibited unauthorized disassembly, no internal user repairable parts.
7.For long periods of time, please pay attention to the power outage, and retain.
8. Pay attention to water, dust, fire when using it.

9. Do not use the corrosive chemical solvents to clean the equipment.
10. Spindle motor bearing life and its speed is inversely proportional.
11. Graver is very sharp. Do not touch when it is running, in order to avoid injury; Do not
use handkerchiefs, scarves contact it to prevent embroiled damage.
Important Notice：
The Company shall not be responsible for any loss caused by improper using or breaking
the correct operating procedures.
Beijing ruizhitianhong S&T co.,Ltd owns this manual final interpretation,the company
reserves the right to modify all information in this manual, including data, technical details,
etc..

CONTENT
Foreword ............................................................................................. 3
1. RichAuto system composition ............................................................ 4
1.1 System composition .................................................................. 4
1.2 Description of Each Component ................................................. 5
2. Instruction to Handle controller keyboard .......................................... 8
2.1 Introduction ............................................................................. 8
2.2 Usage ...................................................................................... 8
2.3 Detail information for key functions ......................................... 10
3. Wiring Instructions ......................................................................... 13
3.1 RichAuto Stepping wiring instructions ...................................... 13
3.2 Patch Board I / O Description .................................................. 14
3.3 Hardware Connection.............................................................. 19
3.4 Commissioning of The Machine and Control System .................. 26
4. Menu direction ............................................................................... 26
4.1 Menu category ....................................................................... 26
4.2 Menu detail ............................................................................ 26
5. Machine operation........................................................................ 41
5.1 Return home .......................................................................... 41
5.2 Import processing files............................................................ 41
5.3 Manual processing operation ................................................... 42
5.4 Automatic machining operation ............................................... 44
5.5 Processing operations ............................................................. 47
5.6 Advanced Processing .............................................................. 50
PS 1. System automatically update ...................................................... 56
PS 2. Common troubleshooting ........................................................... 57

 Foreword
System Introduction：
RichAuto is CNC motion control system independently developed by Beijing ruizhi
tianhong and it can be widely applied to machinery, advertisement, woodworking, mold
engraving machine, laser, flame, plasma cutting machine, and so on in the machine control
field.
RichAuto make DSP as the core control system，High-speed processing operation is
the microcontroller, PLC systems can’t match；Use embedded structure，High degree of
integration，Strong stability，easy to installation and operation；U disk support，Removable
storage card reader，With USB Interface，High speed transfer，Plug and play the full
realization of all work offline。
Characteristics:
1. System deploy standard X, Y, Z axis motion control method ,Support the rotation axis
（C axis）control，Enables to switch the processing of surface and processing of
rotation ; up extended to X, Y, Z, C four-axis motion control, Implementation four axis
interlocking Control.
2. Multi I / O Point Control，there is eight input and output signals in every basic I / O
signal node，Expansion I / O nodes can be expanded to 32 input and output signals。
3. Support the standard G code, PLT format instructions; support domestic and
international mainstream CAM software, such as: Type3, Art cam, UG, Pro / E, Master
CAM, Cimatron, Wentai etc.
4. Provide with power-down protection. Instantaneous power processing system to
automatically save the current processing of information (file name, current line
number processing, processing speed, spindle threshold), when power again machine
moves back, the system automatically prompts the user to restore the processing
Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 1

before power down, the processing operations become more humanity.
5. Support breakpoint memory, file selection, processing. Save 8 different breakpoint
processing information.
6. Multi-coordinate memory function. Provide nine working coordinate system, the user
can switch among the 9 coordinate, each coordinate system can save a process origin
information.
7． Support online adjust spindle operating frequency. The spindle frequency from 0 to
maximum frequency is divided into 8 thresholds; 1 - 8 threshold can be processed
directly adjust up and down without suspend processing.
8． Support adjust speed ratio online. Users can adjust the speed ratio, to adjust the
processing speed and empty running speed, speed ratio values from 0.1-1, Ascending
or descending per 0.1 numerical.
9． Simply manual operate mode. In manual mode, the system provides three kinds of
sports concluding continuous, step (crawl), distance, manual operation became more
simple and convenient.
10. Identifies M code, F code and other development commands, can open a special
code based on user needs.
11. Built-in 512 M memory.
12. Unique handheld form factor with one hand to hold. Own liquid crystal display and 16
key keyboard , operate intuitive and flexible, no longer dependent on the computer,
the full realization of full offline operation
13. C omes with USB communications port, file transfer efficiency can be directly read U
disk, card reader file, Plug and Play.
14. Self-test function, the system comes with I / O port signal detection capabilities, ease
of remote maintenance.
15. Processing with high-speed and smooth, support high subdivide, make sure

processing with high accuracy and high speed.
16． Unique in Chinese-English to show double-interface, can be realized in switching
Chinese and English show online.
17. Multi-language display. Support for Simplified Chinese, Traditional Chinese, English,
Russian, French and other languages, can be customized according to user needs.
18. System can support automatic dynamic upgrades, convenient to remote operation,
remote maintenance.

1. RichAuto system composition
1.1 System composition
RichAuto control system contains the following parts ： A hand-held motion

controller ,a line adapter board, a fifty pin data transmission cable, an USB communication
cable.
RichAuto accessories schematic diagram
Hand- held motion controller Interface board
50-pin data transmission cable USB communication cable
Figure 1-1

1.2 Description of Each Component
1. Handle: the core of the lower computer, it contains six modules.
Handle
(1).LCD：Resolution of 128 * 64 LCD display，To display the machine motion, and
the information, such as the system settings and other information .
(2).Key Board：It contains 16 keys to input the system parameter information

and operate the machine.
(3). U Disk Interface: external memory access ports to U disk and the memory
card. The file format can be identified by the external memory is FAT16/32.
(4).50-pin Data Cable Jack: through 50 pin data transmission cable and line
adapter can achieve the connection between system and the machine. The
system sent the movement to machine motion actuator.

(5).Company LOGO.
(6).USB Communication Port: USB data line access port. It is used to connect
the host computer with r computer.
2. Interface Board: The operation between the low computer and machine is
completed by the link of the interface boards. It contains 6 parts.
Interface board
(1). 50-pin data cable jack: The connection between the system and the
machine can be completed through 50 pin data transmission cable and
line adapter and then the system can sent the movement signal to
machine motion actuator.
(2). Output control terminal：It can control start and stop of the spindle and
gear change. Different connection ways refer to different control. You
can check the details in the menu notes, "spindle set the option" Help.
(3). Input control terminal: The input terminal for the machine origin detection
switch signal.

(4).Power supply terminal: the input terminal for system switching Power
Supply.（DC24V 3A）
(5).Motor drive control terminal: the output terminal for drive control line.
3. 50 pin data transmission cable
4．USB communication cable

2 Instruction to Handle controller keyboard
2.1 Introduction：
RichAuto system handle controller defines 16 operation keys according to the
system functional requirements. Each key has one or more functions under different work
status；
16-key layout Chinese Button really making plans
2.2 Usage:
RichAuto control system divided the key’s operation into one-touch button operation,
and the combined-key operation.
One Touch：Press one button on handheld motion controller.

Combined-key operation：Press two buttons at the same time to achieve the operation;
The operation step: press one main function key and meanwhile press a
second accessibility key, and then release the two keys at the same time to
realize the combined-key operation.
PS: Commonly used combined-key list：
Combined-key Function
to switch the coordinate system (0
for the mechanical coordinate

1
― ‖ + ―0—9‖ Number keys system , 1 - 9 for the work coordinate
system)
2 Start Z-axis automatic tool setting

― ‖ + ― ‖
to start the break processing (support

3 ― ‖ + ―1—8‖ Number
number 1 - 8)
keys
to start the advanced processing

4
― ‖ + ― ‖ modes

5 To switch gear shaft

― ‖ + ― / ‖
6 Repeat last time processing

― ‖ + ― ‖
Operate machine by entering

7
― ‖ + ― ‖ coordinates parameters
8 System update
“ ”+“ ” 键
9 Quit buttons check

“ ”+“ ” 键
2.3 Detail information for key functions：
key Function
Positive movement of X axis, Menu upward , figure 1 inputting

Positive movement of Y axis, accelerate process speed, figure 2 inputting
Positive movement of Z axis, figure 3 inputting, rise spindle speed in
process
Working origin of X axis and Y axis setting, figure 4 inputting
Negative movement of X axis; Menu downward, figure 5 inputting
Negative movement of Y axis; slowdown process speed; figure 6 inputting
different property selecting in Menu
Negative movement of Z axis, figure 7 inputting, spindle speed adjusting
in process
Z axis origin setting ; figure 8 inputting
Axes home to machine tool origin, figure 9 inputting

Manual moving mode, high speed or low speed selection, figure 0
inputting,change work coordinate & mechanical coordinate when auto
work
Spindle startup/stop, decimal point inputting
Menu setting entering, negative symbol inputting, multi process state
checking
All axes go working origin: confirm of motions /inputting/operating
Manual move, continue, step and distance modes selection
Cut process running/pause/inputted words delete
High/low speed parameter adjust, Cut process stop/selections, inputting
and operating cancel

3. Wiring Instructions
3.1 RichAuto Stepping wiring instructions

3.2 Patch Board I / O Description

Port label Port Pin Pin functions Notes
definition Definition and parameters
J10 System main power supply
System System main terminal ，interface board Power area：
Main power supply give DC 5V for system。 DC10V~DC24V/3A~40V
power side When F3 shorted can
provide voltage to XYZ
J2 Were positive X-axis drive common Do not impose voltage on
signal output anode power supply this pin
port terminal 5V output
Pulse signal X-axis drive pulse signal
output output port, the output
X-axis port voltage ≧ 3V drive
pulse current≦ 8mA
output direction X-axis direction of the

port signal drive signal output port
output port output voltage ≧ 3V drive
current≦ 8mA
Shield X-axis drive signal output Do not use this port for the
connection voltage line terminal shield grounding port
port
J3 Were positive Y-axis drive common Do not impose voltage on
Pulse signal Y-axis drive pulse signal
port voltage ≧ 3V drive
Y-axis current≦ 8mA
pulse direction Y-axis direction of the

output signal drive signal output port
port output port output voltage ≧ 3V drive
current≦ 8mA
Shield Y-axis drive signal output Do not use this port for the
connection voltage line terminal shield grounding port
port

J4 Were positive Z-axis drive common Do not impose voltage on
Pulse signal Z-axis drive pulse signal
port voltage ≧ 3V drive

Z-axis
current≦ 8mA
pulse
direction Z-axis direction of the
output
signal drive signal output port
port
current≦ 8mA
Shield
connection Z-axis drive signal output Do not use this port for the
port voltage line terminal grounding port
shield
J5
Were positive
signal output C-axis drive common
port anode power supply Do not impose voltage on
terminal 5V output this pin
Pulse signal C-axis drive pulse signal
C-axis output output port, the output
pulse port voltage ≧ 3V drive
output current≦ 8mA
port
direction C-axis direction of the
signal drive signal output port
current≦ 8mA
Shield C-axis drive signal output Do not use this port for the
connection voltage line terminal grounding port
port shield

J7
Y1(s0)： Connect to FWD of inverter Output Low level signal
Spindle
ON/OFF
Y2(s1)：speed Connect to inverter to Output Low level signal
1 control speed
Output
Control
terminal
2 control speed
3 control speed
Y5(s4)：Alarm Lignt when there is Output Low level signal
LED something wrong with
system
Y6(s5)：Work Lignt when system works Output Low level signal
LED
Y7(s6): user-defined signal Output Low level signal
definable
Y8(s7)： user-defined signal Output Low level signal
definable
GND:output GND connect to this
GND terminal in control inverter
speed mode

Port label Port Pin Definition Pin functions Notes
definition and parameters
J8 X1:X_se：X origin X origin sensor signal Input low level signals
sensor Signal Input input terminal
X2:Y_se：Y origin Y origin sensor signal Input low level signals
sensor input terminal
Signal Input
X3:Z_se：Z origin Z origin sensor signal Input low level signals
sensor input terminal
Signal Input
X4:CutterTool-setting Tool-setting sensor signal Input low level signals
sensor signal input input terminal

input
Control X5：Driver alarm signal Driver alarm signal input Input low level signals
terminal input terminal
X6:Hard limit signal Hard Limit signal input Input low level signals
input terminal
X7：E-stop signal input E-stop signal input Input low level signals
terminal
X8：Definable signal Definable signal input Input low level signals
terminal
24V+：Sensor power X、Y、Z sensor isolate Sensor isolate circuit
input circuit power supply supply voltage range
positive input terminal DC10V~DC24V
GND：GDN X、Y、Z sensor isolate
input circuit power supply
negative input terminal
Sensor signal cable shield Do not use this port as a
Shield：Shield input input terminal negative use of the sensor
isolation circuit power

Interface board 5V indicator
D19 Power LED indicate the interface andinternal Lights after power
power supply status moderators
D11 Status X origin status indicator Light after power.
indicator Input low level
D12 Status Y origin status indicator signal, the lights
indicator will be put out.
D13 Status Z origin status indicator Release the
indicator signal,the lights will
D14 Status Tool-setting Status indicator be bright again
indicator
D15 Status Driver alarm status indicator
indicator
D16 Status Hard Limit status indicator
indicator
D17 Status E-stop status indicator
indicator
D18 Status Definable signal status indicator
indicator
D1 Status output terminal Y1 status indicator
indicator
indicator Output low level
D3 Status output terminal Y3 status indicator signal when the
indicator system works
indicator
D5 Status output terminal Y5status indicator
indicator
D6 Status output terminal Y6status indicator
indicator
indicator
indicator

PS：All the pin terminals are for the parties sort the mouth as the first one, the bit serial
extended direction of the arrow.
3.3 Hardware Connection
Installation Requirements：Switching Power（24V 3A）should add a filter to prevent
interference with the electric field. If origin detecting switch are different power supply
type, the special testing switching power is needed.（24V origin detecting switch is the
best choice）
RichAuto control system realizes its control through the connection between the
interface board and CNC machine. Interface board terminal can be divided into input
terminal and output terminal：
Input terminal includes：
J8（input control terminals）
J10（main power terminals）.
Output terminal includes：
J2（X axis pulse signal output terminal）
J3（Y axis pulse signal output terminal）
J4（Z axis pulse signal output terminal）
J5（C axis pulse signal output terminal）
J7（output control terminal）

Input terminal
1 sensor input ○
1 Mechanical(Y,Z are the same as X)
2 NPN(NO): Y and Z are the same as X

○

3 PNP(NO) : X and Z are the same as Y

○
2 Tool-setting input:Tool-setting detecting wiring：

3 X5-X8 Driver alarm,Hard limit,E-stop signal
J10 Main power wiring:
Output terminal: J2 X pulse signal wiring （Y、Z the same as X）
1 Stepper driver:

2 Servo driver:
J7 Spindle inverter
2 status：spindle start/stop

The corresponding spindle setting is:
8 status：spindle start---S1—speed 1，S2—speed 2，Sn—speed n，when spindle stop，

the screen displays Fn—the speed before spindle stop.
3 lines,8 status

The corresponding spindle setting is:
PS: FWD and DCM has Connected in Parallel in some inverters, plesae do not need to
connect Y1 (S0) in such situations, you only need to connect DCM with GND of interface
board, without having to re-set the spindle gear.
Output Y5-Alarm LED and Y6-WORK LED:
You can connect the machine with the control system when the above setting is over.

3.4 Commissioning of The Machine and Control System
1） After turn on the power, you can manually run each axis movement and decide the
direction. If the direction of movement and definition direction are opposite, you can
set to change the motor phase sequence.
2） According to the original location of the machine coordinates, you can enter into
menu-machine setting-home setting- home direction to reset it.
3） Double-press ―menu‖-manual voltage setup（the upper arrows stand for input voltage）
to check whether the home switch is working.
The machine is in good connection if all the above setting is ok.
4. Menu direction
4.1 Menu category
According to menu function,RICHAUTO system menu can be divided into: machine
setup、auto pro setup、system setup、operate file、version view，every main menu
has corresponding submenus.
4.2 Menu detail
1．Machine setup：
Machine parameter setup is to set machine hardware. This parameter is set by
machine producer according to device type. If machine hardware parameter is not
change this parameter should not change. If machine user need to change，please dell

to machine producer.
Machine setup chart
(1).pulse equiv：
The number of pulses of the system needs to send when machine moves every
1mm.Unit：pulse/mm.
1 stepper driver:
Formula = pulses per revolution / distance per revolution
Pulses per revolution formula: (360 °/stepper angle)* Driver subdivision
Some stepper drivers mark pulse number directly.

Distance/r formula：
Screw drive machine = screw pitch * mechanical transmission ratio
Rack drive machine = rack module * gear teeth number*π* mechanical
transmission ratio
So stepper motor system formula:
Screw drive:
Formula Description: step angle is the angle of the motor parameters, motor
rotation step walk.
Driver subdivison is the parameter set by the driver.
Screw pitch(above picture): The distance that the nut moves when the ball screw
makes one rotation.
Transmission ratio: The speed ratio or angular velocity ratio of the capstan and the
driven wheel.

Rack drive:
Formula Description: step angle is the angle of the motor parameters, motor
rotation step walk.
Driver subdivison is the parameter set by the driver.
Rack module and gear teeth number are gear parameters. rack module * gear
teeth number*πequals the perimeter of the reference circle.
Transmission ratio: The speed ratio or angular velocity ratio of the capstan and
the driven wheel.
setting：
choose ―pulse equiv‖， Cursor in the X-axis pulse equivalent，click ― ‖、
― ‖ move cursor to be modified option，click ― ‖，press the number
keys to enter values，press ― ‖ to save，cursor auto move to next line，in
turn modify the Y, Z axis equivalent value，press ― ‖，save all value，back

to ―pulse equiv‖。
2 servo driver:
The pulse equivalent factory default X,Y,Zare 400，and set the electronic gear ratio
in the servo drive according to the pulse equivalent.
The numerator of the electronic gear ratio represents encoder pulse
number,you can search it in servo driver manual.
The denominator of the electronic gear ratio:
1 screw drive: Handle pulse equivalent(400)* screw pitch * mechanical
transmission ratio
2 rack drive: Handle pulse equivalent(400)*rack module * gear teeth
number*π* mechanical transmission ratio
(2). Table Size
RichAuto system make the table size as the soft limit values, in order to prevent
machine move over travel，machine size must be less than or equal to the value of
the actual motion displacement machine。
setting：Get into ―table size‖，click ― ‖ or ― ‖ to move cursor to be
modified, press ― ‖，input modified number，click ― ‖ to save，cursor

auto move to next line，in turn change Y、Z axis values，click ― ‖ to save all
values，back to ―table size‖。
(3). Spindle Delay：
Set spindle starting time, unit : ms；This is also set how long system start spindle
after read processing file.
(4). Home setup：
Home speed ：set every axis move speed when machine home，system default
speed is X.Y: 3000 MM/Minute, Z: 1800 MM/Minute.
Home sequence：○
1 Z， X and Y 2 Z,X,Y
○
3 Z,Y,X
○ 4 Z only
○
5 X and Y，Z
○ 6 X,Y,Z
○
7 Y,X,Z
○ 8 XY home
○
9 X，Y home
○ 10 Y,X home
○ 11 None home
○
Home direction：set every axis move direction when machine home，this setting
depends on the position where home switch in the machine. Such as the return to
zero switch installed in the machine positive direction so that home direction
should be set ―positive‖ . and vice versa。

set：Get into ―home dir‖，press ― ‖ or ― ‖ to move cursor to be
modified，press ― ‖ to change home direction，click ― ‖ to save
change，back to ―home dir‖。
(5). Voltage setup：
This used to set input and output signal terminal status，when set ↓means
normal open，the same ↑normal closed.
Upper and under arrows
Upper Arrows stand for input voltage setup：
Set input voltage signal terminal status. Input voltage top 4(0,1,2,3)
corresponding to X zero point, Y zero point, Z zero point, tool setting input signal
terminal.
Under Arrows stand for input voltage setup：
Set output voltage signal terminal status. Output voltage top 4(0,1,2,3)
corresponding to spindle on/off, multi-step 1, multi-step 2, multi-step 3 output
voltage status.
Setting mode：Get into ―input voltage setup‖ and ―output voltage setup‖，press
― ‖ and ― ‖ to control cursor to be modified . press ― ‖、

― ‖ to get to upper or under arrows，and press ― ‖ to change
terminal status.
(6). C.A.D. Thickness：
This thickness should input by actual， when above actual Z axis will cut over,
when low to actual Z axis can’t touch workpiece. This parameter can only take
effect when user use auto tool change function.
(7). Max Spd Limit：
Set machine top speed, this set can only take effect when machine processing,
system default max speed X,Y is ‖60000000‖, ―Z+‖ is ―1800‖, ―Z-‖ is ―3000‖.
(8). Spindle Line Count：
3
If line=3,Spindle Statues=2 =8
(9). Spindle Statue：
When system using multi-step speed to control spindle, user should change this
parameter. This parameters must corresponding to spindle output signal terminal
wiring sequence. Detail setting please see ―spindle setup‖.
(10). Check Input
1-3:X,Y,Z home signal 4: tool setting input signal
5-7:driver alarm,hard limit,E-stop signal

(11). Check Output
1：spindle On/off signal 2-4: Spindle speed signal 5: Driver alarm signal
6：work LED signal
(12). Wipe Cache
Clear file fragmentation and error,operate it after system update.
(13). Distance mode time limit
You select diatance mode,and if the machine never moves in a certain period of
time(system default is 30 seconds),the system will go back to continuous mode.
2．Auto pro setup：
This set processing parameters and process files read property.
Auto pro setup menu structure

(1) acceleration ：
This parameter can improve the ability to handling line and curve motion, unit:
mm/s2 System default acceleration is 800.
(2) work speed：unit:mm/min
Including work speed and fast speed. system default work spd is 6000;fast spd is
3000.
(3) Safe height：
This can tell us how long the file can process. Unit: mm.
(4).Auto scale：
Auto pro speed=Auto scale*work speed,it does not affect the fast
speed.
(5).Fall scale：
Include fall down scale and fall hight. system default fall down scale is
0.200,fall hight is 5.000mm. Fall down scale takes effect when the spindle falls to
the fall height.

(6).Stop Statue：Setup stop position after auto pro.
Setup stop position，press “ ” or “ ”to where to change
thenumber，and then press “ ”to input the number needed，
press“ ” to save.Press“ ”to get into finish action list
press “ ” or “ ”to where to change the statue，and press
“ ” to save.
(7).G Code Setup：
Set special code read configure in G code ，such as M、T、F、I、J、K ，the detail
please see ―G Code Setup‖

(8).Circle Limit：
System default circle limit is 1000.000.
(9).Work Array：
Setup array parameter,include columncount 、 Rowcount 、 Columnspace 、
Rowspace、Interval（unit：ms）.
(10).Start Speed：unit:mm/min, System default start speed is 100.000 mm/min.
Reduce the noise of the low-frequency vibration of the motor, machine run
Smooth from Stationary state to the work speed.
3．System setup：
System setup menu structure

(1). Languages
Change system display language，choose Chinese and English.
(2).Backup Data Password
Prevent customers backup parameters which overwrite the original correct
parameters when by misoperation or when the system parameters disorder.
Cancel the password,when the display shows ―input new password‖,do not input
any number,and press button ‖OK‖.
(3). Data initial
After data initial system parameters will restore factory setting.
(4). Inner format：
Clear up inner files.
(5). Screen Lock
The screen will lock when the time reachs to the number you setup，and then input
the password to unlock the screen.
(6). Probation password
You can get a 20-digit-password from the website of ourcompany.
(7). Buttons check
Test the validity of the keyboard keys. Into test interface，the screen displays

highlights when key take effect, no highlights when key is broken. Press ―ok‖+
―cancel‖ to quit.
(8). Backup Data
Back up menu parameters，format system can’t effect this.
(9). Restore Data
Restore backup data to system.
(10). Auto Update
Update system online. Support the extension ******.PKG update file.
4．Operate File
Advanced pro setup menu structures
(1) Copy File
Copy files of U disk to Inner.

(2) Delete File
Delete files of inner.
(3) View Flie
View the files of U disk and inner.
(4) Processing information
Statistical the number of files processing successfully.
PS:Plesae pull out the U disk correctly after copying files from computer,if
not,the controller may not recognize the U disk.
1． Win7(32 bit) system：after copying files,please press“ ”,and then the
display will show “ ”,choose the device to be shut

down.when the display show
“ ”,the U disk pull out
from computer successfully.
2． Win XP system：after copying files,please press“ ”,and then the display
will show “ ”,choose the device to be
shut down.when the display show “ ”,the U disk pull out
from computer successfully.

5．Version View
Include：○
1 Product ID eg：A0020112 2 Soft Version eg：A1.497
○
3 Emergency Version eg：A1.470

○ 4 Update Version eg：P1.440
○
5 Soft type
○ 6 Hardware type
○
5. Machine operation
5.1 Return home
The handle will prompt ―All Axis home‖、

“Z home only”、
“none axis home” after
starting，choose anyone you want.
In some cases, such as after the last normal shutdown, reboot and continue last
operation, users don’t need to reset machine，choose “none axis home”. That is because
when system quit, it is auto save coordinate value.
5.2 Import processing files
Before processing，generally we should import files. There is 2 ways : U disk，inner file
process.
1. Directly import processing files to U disk, we can be run.
2. Downloading files into handle by U disk.

5.3 Manual processing operation
Manual processing is means we control machine through keyboard. The same we
can change operation speed and grid setting. After return home, system into manual
status, the screen displays:
1X 0.000 manual
1Y 0.000 stop
1Z 0.000 high
Continue
1. Manual operation speed adjust
There is two modes: high speed and low speed. We can change mode by
“ ”.The screen displays speed mode can decide processing speed.
Speed adjust: in manual mode, press ―cannel‖ to set the current speed mode. If
current speed is low speed, it displays as followed:

Low spd，mm/min
X axis： 1200.00
Y axis： 1200.00
Z axis： 600.00
Dell：010-62970368 82923063. Fax: 82920078 URLLow grid 0.100

：www.richnc.com.cn 42
The cursor in X axis low speed mode , press “ ” and “ ” move cursor
to be modified , press “ ” that we can change value, press “ ” to save，
press “ ” to quit，if number input is wrong, press “ ” to delete the
last number.
In order to ensure the accuracy of processing and debugging, the system
introduces the concept of grid. Other systems also call it minimum feed. Its range is：
0.05mm-1.0mm. when user change mode to step, machine will move by grid.
High speed mode setting is the same as low speed mode.
2. Manual processing mode
In order to meet manual movement in different situation, this system provides 3
motion modes: continuous, step, distance. We can change mode by ― ‖. The

bottom of the screen can display which mode system is on.
1) Continuous motion mode
This mode is no special data control, in this mode, press direction key（、
、、、、） machine will follow, its speed is decided
by current speed mode.

Notice ：if user press key’s time is too short（shorter than 0.5s）
，immediately lift
buttons，machine will auto move to the nearest grid. It is always stop on grid when
this motion mode is over. This motion mode is suitable for crude regulation machine
coordinate situation.
2) Step motion mode
This mode is always run in low speed, move a grid per 0.5 second ，its grid
distance is decided by current speed mode. This motion mode is suitable for tool
adjust or precise adjust machine coordinate situation.
3) Distance motion mode
This mode is run by distance which user is set. When user press directory key
（、、、、、），machine will move by set distance.
Notice: Grid can’t effect to this motion. It will move by set distance, can’t move to
grid point.
If user want to change distance, please change to distance mode, re-enter distance
value is ok.
5.4 Automatic machining operation
Auto processing is means system deal files in U disk and inner by command，this is
also called file processing。Before auto processing, the parameters in system and
machine must be correctly set.

Steps:
1) Determine the origin of the workpiece
The origin of the coordinate of XYZ in the processing program is the origin of
workpiece. Before processing, we should connect the situation to the actual . The
operation is as followed:
Move the machine to the situation where the file start processing. Press ― ‖ to
set the origin of X Y axis, press ― ‖ to set Z axis. If used tool setting function,
its no need to press― ‖ to set origin，the key combination of tool setting is
― ‖+― ‖。
2) Choose processing files
After determining the origin of workpiece，press “ ”，the following dialog box
appears:

Press “ ” and “ ” to move the cursor，press “ ” to choose
the situation，it will displays the first three files, press “ ”and “ ” to
move cursor，press “ ” and “ ” to jump 2 lines, press “ ”
to quit.
3) Processing parameters setting
After choosing processing file press “ ” into setting processing parameters,
including processing speed, travel speed, Z down ratio, speed ratio, spindle grad,
pulse equivalent, and Z up distance.
Press “ ” and “ ” to move cursor to be modified, press “ ”

to set, input value, press “ ” to save, press “ ” and “ ” to
select the next. After modifying, press “ ” to save, system start checking
files。It will start processing after checking system. Pulse equivalent there can only
display can’t be modified. If need to change, please back to “machine setup”。In
processing ， the screen will display current line, current speed, speed ratio,
operating time. We can switch these option by pressing “ ” 。
5.5 Processing operations
1) Adjust speed ratio and spindle grade
Adjust speed ratio In processing ，press “ ” and“ ” can
directly change ratio，current speed =set speed*ratio，each click “ ”，ratio
down drop 0.1。Speed ratio max 1.0，min 0.1，the display speed will corresponding
change, but time will not change.
Adjust spindle grade this function can take effect when system set multi-speed.
In processing, press “ ” and “ ” to change spindle grade 。Each click
“ ”，up 1 grade, S8 is the top。Each click “ ”， drop 1 grade, till to S1。

2) Processing pause and adjust situation
Press “ ” to pause，top right corner of the screen will change ―run‖ to ―pause‖ ,
machine will stop running except spindle. Shown below：
1X 7.200 pauz
1Y 41.300 s-on
1Z -0.200 step
Line No. 356
In this time we can adjust situation of 3 axis, the default motion mode is step,
speed is low, users can change situation, that is means machine will move a low
speed grid each click; if we need quickly a large range adjust, change the speed
mode to high by press “ ” , the motion mode change to continuous.
After that，press “ ” ，shown ：

1X 7.200 Pauz
1Y 41.300 S-ON
1Z -0.200 Step
Restore Position？
System will let users make sure whether to save the modified
Original？
Situation, press “ ”，system will back to situation before modifying；press
“ ”， system will start processing in modified situation.
3) Breakpoint processing and power-down protection
Breakpoint processing if user want to stop processing in middle ，press
“ ” ，shown below：
1X 7.200 RUN
1Y 41.300 S1
1Z -0.200 1.0
Save break？
System display ―save break?‖，if we want to save breakpoint, press “ ” ， LCD
Original？
displays break list（total 8），press “ ”or“ ” to choose position，and then
press“ ” to save ，system auto home. If we want to continue processing from
breakpoint，we can choose key combination― +1-8‖ ，first hold on press“ ”,
the same time press number key（1-8），release together，system will restore processing
from point 1. If you want to fallback from the breakpoint,press“ ”, input the

line number,and then press “ ”,the system will work from the new line
number. Before restore process, system must have a home motion. eg：If we want to
continue processing from breakpoint ， we can choose key combination “ ”+
“ ” ，first hold on press “ ”, the same time press “ ”，release together，
system will restore processing from point 1，the same as 2-8.
4) Power-down protection
when there is a sudden power failure during processing, system will save current
Want to restore？
coordinate and parameters, when power restart, process continue. Before that,
system must have a home motion, after home, shown as below:
Press “ ” to continue unfinished process, it will display the stop line, press
“ ” to cancel process.
5.6 Advanced Processing
advanced processing is a function which is satisfied for some special request. It
contains: Array work, Resume work, Tool changing,Part work,calculate bound，the

key combination is “ ” + “ ” ，shown below：
1）Array work
1.press and move cursor to multiple process ， press to
enter，press and to select different files；
2 . Set process parameters, other operation is the same as general process, system
start multiple processing according to users’ set；
3．You can also setup in Auto Pro Setup – Work Array.

2 ) Resume work
First we should set multiple process parameters in ―advanced setup ‖，then we can
use this function。Step is as below：
1.press “ ”and “ ” move cursor to Resume work，press “ ” to
enter.press“ ” and “ ” to select different break points，and then
press “ ”， system will restore processing from the break point.
3) Tool changing
Achieve manually change the tools in the position you set. Press “ ” get
Into the setup，and also press “ ” back to work origin.
4) Part work
Part work means users can select start line and end line, so part of the processing
file can be processed. The step is as below:
1 press “
○ ” to set，press “ ” and “ ” to move cursor to select
different file list；

2 press “
○ ” to enter，press “ ” and “ ” to select file，
press“ ”， start to read the file.
3 after read the file，press “

○ ” screen displays line 1 of the code, press
“ ” ，prompted ‖input start number：displays total lines ‖, input start line to
cursor，press to confirm ，if line number is wrong，press to delete
input number.
4 Press “
○ ” to the operation of the end line，the screen displays “input
end number”，P r e s s “ ” he screen displays the changed start number，
press “ ”， Input end line in cursor，press “ ” to confirm, press
“ ” to modification；
5 Set processing parameters.

○
5) Calculate bound
Calculate area of the file.

1 Press “
○ ” to set，press “ ” and “ ” to move cursor to select
different file list；
2 Press “
○ ”to get into file list，and then press “ ” and “ ”
to choose file；
3 Press “
○ ”，start to read the file，after reading the file，the system will
calculate the area.
6) Calculate bound
Including Scan Mill and Encircle Mill
The step is as below:
1 Scan Mill
1 Press“
○ ”和“ ” to select different type.
2 Press“
○ ”to get into the milling plane parameters，including scantype、
width、height、diameter、depth and Z step.

Press― ‖and― ‖to select the parameter to be setted，Press― ‖to select
scantype（X Scan and Y Scan）and the parameter，Press― ‖to save.
2 Encircle Mil
1 Press“
○ ”and“ ” to select different type.
2 Press“
○ ”to get into the milling plane parameters，including scantype、
width、height、diameter、depth and Z step.
Press― ‖and― ‖to select the parameter to be setted，Press― ‖to
select scantype （ clockwise and anticlockwise ） and the parameter ，
Press― ‖to save.

PS 1. System automatically update
In the process of using handle, there may be some minor problems,these problems
update handle software can be restored.
U disk update
This method is update by handle operation, don’t need PC. Update files is *.PKG. Step is
as below:
1、 Save update files to U disk, insert into handle.
2、 Press “ ”，select ―system setup‖ press “ ” to enter， press “ ”
and “ ” move cursor to ―system update‖。
3、 Press “ ” to enter，select ―U disk files‖, select update files suffix is *.PKG.
System will auto update.
4、 After update, please restart the handle.

PS 2. Common troubleshooting
Solutions of the faults display on the screen

1 Indefinite screen flicker or automatically restart
Analysises and solutions:
1、 Power supply is insufficient. Check power supply if there are problems, and change
high-quality power supply to solve the problems.
2、 The local power grid unstable. Check local grid voltage instability,or increase the the
regulator filter device.
3、There are something wrong with the power chip of the handle. This phenomenon also
appears when the handle is powered through the USB cable to the computer,please
return back the handle to our company.
2 Can not set working origin
1、 You may get into the mechanical coordinate system. Press the button "menu" + "1"
to back to the first work coordinate system.
2、 The buttons are broken.menu-system setup- buttons check，to check the buttons are
normal or not.

Faults in practical operation

1 The file size does not match the size of the actual set
1、 Pulse equivalent is wrong.
2、 You does not select the right tool.
2 The screen displays‖beyond limit‖when processing file
1、 The machine is not carried back to zero, the system is not able to confirm the actual
position. Make the machine back zero.
2、 After setting the working origin, the reserved range is less than the actual file
size .Determine the actual file size and set correct working origin.
3、 You set the wrong working origin in the file. Check the path of the file, and re-export
the correct file.
3 Z axis（spindle） fall down abnormally（too fast）during processing
1、 Working speed beyond the fastest speed of Z axis. " Machine setup " - " Max speed
limit "，set the speed to the safe speed.

2、 Coupling is loosing or transmission slippages. Re-adjustment the connecting parts.

3、 The lines connect the interface board with the motor drivers has
disruption. Re-adjust the lines.
4、 Processing file error. Check processing file, try to download the correct processing file
to U disk or handle internal.
5、 There is something wrong with the lines connectting Z axis motor and motor
driver. Replace the lines.
4 Each time repeating the same processing file after backing to the
machine origin ，Z axis depth is not the same
1、Machining countertop is uneven or processing object not firmly fixed, re-milling
countertop adjust the flatness.
2、Z-axis origin detection switch repeat positioning accuracy error, causing each Z axis
homing error. Replace a high-quality detection switch.
3、Too much interference in the Z-axis homing process to form a false origin. Re-adjust the
line.
5 Back to the origin ，the machine can not stop
Double click on the "menu" key，input signal (origin detection switch signal) self-testing,
whether the detection signal is triggered or connect normally.
1、The the origin detection switch is damaged. Replace a new one.

2、The distance of the origin detection switch detection sheet beyond the detection range
of the switch, adjust the position of the test piece.
3、The origin detection switch to the interface board wiring aging or loosening. Again check
the connections.
4、 The interface board is broken. Depot Repair.
5、50-pin data cable is broken. Replace it with a new data line.
6 Back to the machine origin ， machinemove to the reverse
direction
1、 The origin detection switch types do not match with the definition of the
corresponding level. Modify the level. (Normally open type corresponds to a level
defined the direction of the arrow down, normally closed type corresponds to the
level defined arrow up)
2、 The origin detection switch is damaged. replace a new one.
3、The origin detection switch connects interface board not well. Refresh the line to
determine the wiring is correct.
4、Too much interference, resulting in the illusion of the detection switch has been
triggered. Recalibrated the whole circuit.
5、The interface board is broken. Depot Repair.

6、50-pin data cable is broken. Replace the data line.
7 Abnormally working when processing file or the actual file is
different from theoretical file
1、 The program disorder.
2、 External interference is too large.Refresh connection. (separate strong electirc from
weak current, "GND" of inverter separated from the other components )
8 Start automatic tool setting, the tool does not stop after touching
feeler bolock
1、 "cutter" signal line connects "cutter" terminal not well.
2、 The "GND" terminal of interface board does not connect with spindle shell or connect
not well.
9 Handle LCD digital changes, the machine does not move
If one axis is not moving, it may be a connection problem.Change another normal terminal
to this terminal,if it is ok,the motor dirver is ok.Maybe there is something wrong with
interface board、50-pin cable. If it is still not moving, it is necessary to detect the

corresponding drive and motor.
If all axises are not moving ,firstly check if there are problems in the 50-pin cable and
interface,secondly check the power supply of the motor drivers. Lastly, you have to check
the mechanical part .
10 It is normal to the move from one location to another location,
but when return from that position to the original position is not
normal
Mechanical problems，screw may install not well.
Electrical components and wiring

problem
1 an axis or multi-axis only one-way movement after handle
power-on

1、There is something wrong with the lines connect the interface board with the motor
driver， check the connection.
2、Interface board is damaged. Replace the interface board.
3、The motor driver is damaged. Replace the driver.

2 The certain axis motor does not move after handle
power-on

1、 Operator makes pulse line and direction line oppositely，rewiring it.
2、5V common anode end of the motor driver disconnected, check the connection.
3、The motor driver is damaged, operator can promote motor after handle power-on.
4、 The chip of the interface board damages, no pulse signal output.
3 Screen is not bright after handle power-on ， and
connected handle to computer with a USB cable the screen
displays normal
1、The handle does not connect to power supply. Check DC24V power supply output
normal or not, if normal please check the cable from the power supply to the interface
board.
2、The 50-pin cable is damaged or the interface is broken.
4 Screen is not bright after handle power-on，and connect
the handle to computer by USB cable,the screen is also not
bright.

1、This phenomenon may due to the handle shocked by external force or fall on the ground,
causing the crystal processor damaged. Depot Repair.
2、 operator connect high voltage power supply， Depot Repair.
5 The screen display“spindle on”，actually the spindle off，
the screen display“spindle off”，actually the spindle on
1、 There is something wrong with wires. organize your wires
2、The output level definition is wrong. Modification correct output level definition.
6 Screen is not bright after handle power-on
1、 The power supply voltage is too big or the chip is broken because operator makes
positive and negative of the power oppositely. Depot Repair.
2、The power supply is damaged. Replace the power supply.
3、50-pin data cable damaged. Replace the data line.
4、 handle 50-pin interface damage. Depot Repair.

DSP A11 Manual PDF

Uploaded by

DSP A11 Manual PDF

Uploaded by

Beijing RuiZhitianhong technology Co.

RUIZHITIANHONG S&T Co.,Ltd

A11-Three axis mechanical carving

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn

Thank you for choosing the products!

This manual detailed knowledge of the system characteristics、operational processes、

environment. Operating ambient temperature 0-70 ℃, working environment humidity

interruption of data transmission.

6. Prohibited unauthorized disassembly, no internal user repairable parts.

8. Pay attention to water, dust, fire when using it.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn

9. Do not use the corrosive chemical solvents to clean the equipment.

use handkerchiefs, scarves contact it to prevent embroiled damage.

the correct operating procedures.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn

tianhong and it can be widely applied to machinery, advertisement, woodworking, mold

RichAuto make DSP as the core control system，High-speed processing operation is

the microcontroller, PLC systems can’t match；Use embedded structure，High degree of

integration，Strong stability，easy to installation and operation；U disk support，Removable

realization of all work offline。

（C axis）control，Enables to switch the processing of surface and processing of

rotation ; up extended to X, Y, Z, C four-axis motion control, Implementation four axis

signal node，Expansion I / O nodes can be expanded to 32 input and output signals。

CAM, Cimatron, Wentai etc.

4. Provide with power-down protection. Instantaneous power processing system to

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 1

before power down, the processing operations become more humanity.

5. Support breakpoint memory, file selection, processing. Save 8 different breakpoint

maximum frequency is divided into 8 thresholds; 1 - 8 threshold can be processed

directly adjust up and down without suspend processing.

or descending per 0.1 numerical.

simple and convenient.

code based on user needs.

11. Built-in 512 M memory.

the full realization of full offline operation

disk, card reader file, Plug and Play.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 2

processing with high accuracy and high speed.

16． Unique in Chinese-English to show double-interface, can be realized in switching

Chinese and English show online.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 3

1. RichAuto system composition

1.1 System composition

RichAuto control system contains the following parts ： A hand-held motion

RichAuto accessories schematic diagram

Hand- held motion controller Interface board

50-pin data transmission cable USB communication cable

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 4

1.2 Description of Each Component

1. Handle: the core of the lower computer, it contains six modules.

(1).LCD：Resolution of 128 * 64 LCD display，To display the machine motion, and

the information, such as the system settings and other information .

(2).Key Board：It contains 16 keys to input the system parameter information

system sent the movement to machine motion actuator.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 5

machine motion actuator.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 6

3. 50 pin data transmission cable

4．USB communication cable

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 7

2 Instruction to Handle controller keyboard

RichAuto system handle controller defines 16 operation keys according to the

16-key layout Chinese Button really making plans

and the combined-key operation.

One Touch：Press one button on handheld motion controller.

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 8

realize the combined-key operation.

PS: Commonly used combined-key list：

to switch the coordinate system (0

for the mechanical coordinate

2 Start Z-axis automatic tool setting

to start the break processing (support

to start the advanced processing

Dell：010-62970368 82923063. Fax: 82920078 URL ：www.richnc.com.cn 9

5 To switch gear shaft