DRTECH User Manual

DRTECH
EVS 2430Wi / EVS 2430GWi

Safety and Regulatory Information
with User’s Manual
1
EVS 2430Wi User’s Manual To Customers
To Customers
Thank you for purchasing the DRTECH Radiography EVS 2430Wi (hereinafter, this Product). This User’s
Manual explains how to use the detector, x-ray interface unit, and other peripheral equipments. Before
using this product, be sure to read this manual thoroughly in order to utilize it more effectively. Also, please
read the Operation Manual for EVS Calibration and configuration Software (hereinafter, ECali1).
Important information on usage and maintenance of equipment

1. Only a physician or legally certified operator should use this product.
2. The equipment should be maintained in a safe and operable condition by maintenace personal.
3. Use only computers and image display monitors complying with IEC 60601-1 or IEC 60950-1 and under a system
configuration complying with IEC 60601-1-1. For details, consult your sales representative or local DRTECH dealer.
4. Use only the dedicated cables. Do not use any cables other than those supplied with this product.
Disclaimer
1. In no event shall DRTECH be liable for any damage or loss arising from fire, earthquake, any action or accident by
a third party, any intentional negligent action by users, any trial usage, or other usage under abnormal conditions.
2. Roentgenography, image processing, image reading, and image data storage must be performed in accordance
with the laws of the country or region in which the product is being used. The user is resposible for maintaining the
privacy of image data.
3. In no event shall DRTECH be liable for personal physical harm or property damage that is sustained when the
instructions are not followed or the product is misused.
4. It is the resposibility of the attending physicians to provide medical care services. DRTECH will not be liable for
faulty diagnoses.
5. In no event shall DRTECH be liable for direct or indirect consequential damages arising from the use or
unavailbility of this product. DRTECH shall not be liable for loss of image data for any reason.
6. In no event shall DRTECH be liable for any damage arising from moving, alteration, inspection or repair by a
person other than authorized service engineers.
7. Specifications, compositions, and appearance of this product may change without prior notice.
DRT-MAN-092 2
EVS 2430Wi User’s Manual Contents
Contents
To Customers .......................................................................................................................................... 2
Contents ................................................................................................................................................... 3
Safety notices .......................................................................................................................................... 7
1. Safety Information .................................................................................. 8

1.1. Safety precautions ........................................................................................8
1.2. Notes for using the equipment ................................................................ 13
2. Introduction ............................................................................................ 16
2.1. Features ....................................................................................................... 16
2.2. System Configuration................................................................................ 17
2.2.1. Basic Configuration .......................................................................................................................... 17
3. Product Description ............................................................................. 21

3.1. Product Components ................................................................................ 21
3.1.1. Auto Trigger Mode (AT Mode) ...................................................................................................... 21
3.1.2. Synchronization Trigger Mode (Sync. Mode) ....................................................................... 22
3.1.3. USB SW Mode ...................................................................................................................................... 23
3.1.4. Workstation (Recommended and minimum but NOT included) ................................ 24
3.1.5. Grid (Recommended but Not included) .................................................................................. 24
3.2. X-ray Imaging Condition ........................................................................... 25
4. Components and Specifications ........................................................ 26

4.1. Detector ....................................................................................................... 26
4.1.1. Detector Specification ..................................................................................................................... 26
4.1.2. Detector Component ........................................................................................................................ 27
4.2. Battery Charger and Battery Pack and Adaptor .................................... 28
4.2.1. Battery Charger ................................................................................................................................... 28
4.2.1.1. Battery Charger Specifications .................................................................................................................................. 28
4.2.1.2. Battery Charger Components ..................................................................................................................................... 28
DRT-MAN-092 3
4.2.2. Battery Pack .......................................................................................................................................... 29
4.2.2.1. Battery Pack Specification ........................................................................................................................................... 29
4.2.2.2. Battery Pack Components ............................................................................................................................................ 29
4.2.2.3. Charging Battery Pack .................................................................................................................................................... 30
4.2.3. Adaptor .................................................................................................................................................... 30
4.3. Wireless Charging System ....................................................................... 31
4.3.1. EVS-WPCS ............................................................................................................................................. 31
4.3.1.1. EVS-WPCS Specifications ............................................................................................................................................ 31
4.3.1.2. EVS-WPCS Components ............................................................................................................................................... 31
4.3.1.3. TX / RX Module Specification ...................................................................................................................................... 32
4.3.1.4. RX Module Components ................................................................................................................................................ 32
4.3.1.5. EVS-WPCS Operations ................................................................................................................................................... 33
4.3.1.6. Attach Direction .................................................................................................................................................................. 33
4.3.1.7. Indicator LED Connector Description .................................................................................................................... 34
4.3.1.8. Indicator LED Connector Description (Isolation) ............................................................................................. 34
5. Operating Procedure ............................................................................ 35

5.1. Preparing to Use the Detector.................................................................. 36
5.1.1. Standard Configuration................................................................................................................... 36
5.1.2. Battery Pack .......................................................................................................................................... 37
5.1.2.1. How to Attach a Battery Pack ..................................................................................................................................... 37
5.1.2.2. How to Detach a Battery Pack .................................................................................................................................... 37
5.1.2.3. How to Charge Battery Packs ..................................................................................................................................... 38
5.2. Hardware Installation ................................................................................. 40

5.2.1. Connecting Device ............................................................................................................................ 40
5.2.1.1. Operating AP ........................................................................................................................................................................ 40
5.2.1.2. Functional Cable ................................................................................................................................................................ 42
5.2.2. Operating Detector ............................................................................................................................ 44
5.2.3. Image Data Retransmission .......................................................................................................... 49
5.3. Ending Use of the Detector ...................................................................... 50
5.4. Detector Initialization ................................................................................. 50
6. Extension Facility ................................................................................. 51

6.1. X-ray Generator Interface.......................................................................... 51
6.1.1. X-ray Exposure Mode ....................................................................................................................... 51
6.1.2. Auto Trigger(AT) Mode .................................................................................................................... 52
6.1.2.1. Recommendation of setting AT Sensing Area ................................................................................................... 53
DRT-MAN-092 4
6.1.3. USB SW Mode ...................................................................................................................................... 54
6.1.3.1. Wiring USB SW Mode ...................................................................................................................................................... 55
6.1.3.2. Connector Description.................................................................................................................................................... 55
6.1.3.3. Connector Pin Assignment .......................................................................................................................................... 56
6.1.3.4. X-ray_UNIT ............................................................................................................................................................................ 56
6.1.3.5. Hand Switch.......................................................................................................................................................................... 56
6.1.3.6. PC USB .................................................................................................................................................................................... 56
6.2. Software Installation .................................................................................. 57

6.2.1. Software Classification ................................................................................................................... 57
6.2.2. Software Installation ......................................................................................................................... 57
6.3. Windows Environment Setting ................................................................ 58
6.3.1. Network Communication ................................................................................................................ 58
6.3.2. Disabling Sleep Mode on Monitor .............................................................................................. 61
7. Device Setting ........................................................................................ 62

7.1. AP Setting .................................................................................................... 62
7.1.1. AP Configuration ................................................................................................................................ 62
7.2. Detecting Setting ........................................................................................ 64
7.2.1. Detector Configuration .................................................................................................................... 64
7.2.2. Detector Power Save Management ........................................................................................... 66
8. Troubleshooting .................................................................................... 68
8.1. Failed to Turn the Detector On ................................................................. 68
8.2. Errors in Detector LED .............................................................................. 68
8.3. The LINK LED does Not Turn on .............................................................. 69
8.4. Rapid Consumption of Battery ................................................................ 69
8.5. Battery Pack or Installation Part of Battery is Getting Hot ................. 70
8.6. The Power Switch of SSU or Status LED is not working ..................... 70
9. Maintenance and Inspection ............................................................... 71
10. Specification ...................................................................................... 72

10.1. Main Specifications ................................................................................. 72
10.1.1. EVS 2430Wi X-ray Detector ....................................................................................................... 72
DRT-MAN-092 5
10.1.2. Battery Charger System .............................................................................................................. 73
10.1.3. Battery Pack ...................................................................................................................................... 74
10.1.4. EVS-WPCS ......................................................................................................................................... 75
10.2. Charateristics ........................................................................................... 76
10.3. Packing...................................................................................................... 77
10.3.1. Product Configuration List ........................................................................................................ 77
10.3.2. Assemble Package ........................................................................................................................ 78
10.3.3. Detector Panel Package .............................................................................................................. 79
10.3.4. Component Box Assemble Package .................................................................................... 80
10.3.4.1. AP Box Component ....................................................................................................................................................... 80
10.3.4.2. Battery Box Component .............................................................................................................................................. 80
11. Regulatory Information.................................................................... 81

11.1. Radio Frequency(RF) Compliance Information .................................. 81
11.2. Labels and Marking on the Equipment ................................................ 83
11.2.1. Detector ............................................................................................................................................... 83
11.2.2. Battery Charger and Battery Pack ......................................................................................... 85
11.2.2.1. Battery Charger ................................................................................................................................................................ 85
11.2.2.2. Battery Pack ....................................................................................................................................................................... 85
11.2.3. EVS-WPCS ......................................................................................................................................... 86

11.2.4. Symbol Description ....................................................................................................................... 87
11.3. Guidance and Manufacturer’s Declaration for EMC .......................... 88
12. Warranty ............................................................................................. 92
DRT-MAN-092 6
EVS 2430Wi User’s Manual Conventions
Safety notices
The following safety notices are used to emphasize certain safety instructions. Follow the safety instructions in this
User’s Manual along with warning and cautions symbols. Ignoring such warnings or cautions while handling the
product may results in serious injury or accient. It is important for you to read and understand the contents of this
User’s Manual before attemting to use the product.
This notice used to idendifiy conditions under which improper use of the
WARNING product may cause death or serious personal injury.
This notice used to idendifi\y conditions under which improper use of the
CAUTION product may cause minor personal injury.
This notice used to idendifiy conditions under which improper use of the
CAUTION product may cause property damage.
This is used to indicate a prohibited operation.
Prohibited
This is used to indicate an action that must be performed.
This is used to indicate important operations and restrictions.

IMPORTANT Be sure to read this notice to prevent property damage or malfunction.
This is used to indicate operations for reference and complementary

information.
Users are recommended to read this notice.
DRT-MAN-092 7
EVS 2430Wi User’s Manual 1. Safety Information
1. Safety Information
1.1. Safety precautions
Follow these saftey guides and properly use the equipment to prevent injury and damage to any equipment/data.
WARNING
Installation and environment of use
- Do not use or store the equipment near flammable chemical such as alcohol, thinner,
benzine, etc.
If chemicals are spilled or evaporated, it may result in fire or electric shock through contact with
electric parts inside the equipment. Also, some disinfectants are flammable. Be sure to take care
when using them.
Prohibited - Do not connect the equipment to anything other than specified connectoins.
Doing so may result in fire or electric shock.
Power supply
- Do not operate the equipment using any type of power supply other than the one
indicated on the rating label.
Otherwise, it may result in fire or electric shock.
- Do not handle the equipment with wet hands.
You may experience an electric shock that could result in death or serious injury.
- Do not place heavy object such as medical equipments on cables and cords, or do not
pull, bend, bundle, or step on them. These precautions are required to be followed to
prevent sheathes of cables and cords from being peeled. Do not alter the cables and
cords.
Doing so may damage the cords which could result in fire or electric shock.
Prohibited - Do not supply power to more than one of equipment using the same AC outlet.
- Do not turn on the system power when condensation has formed on the equipment.
- Do not connect multiple portable socket-outlets or extension cords to the system.
-
- Securely plug the power cord into the AC outlet.

If contact failure occurs, or if dust or metal objects come into contact with the exposed metal
prong of the plug, fire or electric shock may result.
- Be sure to turn OFF the power to each of equipment before connecting or disconnecting
the cords.
Otherwise, you may get an electric shock that could result in death or serious injury.
- Be sure to hold the plug or connector to disconnect the cord.
If you pull the cord, the core wire may be damaged, resulting in fire or electric shock.
DRT-MAN-092 8
WARNING
Handling
The system, in whole or in parts, cannot be modified in any ways without any written approval from DRTECH.
- No modification of this equipment is allowed

- Never disassemble or modify the equipment.
Doing so may result in fire or electric shock. Also, since the equipment incorporates parts that
may cause electric shcok as well as other hazardous parts, touching them may cause death or
serious injury.
- Do not place anything on top of the equipment.
The object may fall and cause an injury. Also if metal objects such as needles or clips fall into he
Prohibited equipment or if liquid is spilled, may result in fire or electric shock.
- Do not hit or drop the equipment.
The product may be damaged if it recieves a strong jolt. Using a damaged equipment without
repair may result in fire or electric shock.
- Do not touch connector or inside of access cover.
- Have the patient take a fixed posture and do not let patient touch the parts unnecessarily.
If a patient touches connectors or switches, it may result in electric shock or malfunction of the
equipment.
When a problem occurs
- If any of the following problems occur, immediately turn OFF the power to each piece of
equipment, unplug the power cord from the AC outlet, and contact your sales
representative or local DRTECH dealer:
When there is smoke, when an odd smell or abnormal sound occurs.
When liquid has been spilled into equipment or metal object has entered through an opening.
When the equipment was dropped and damaged.
Maintenance and inspection

- When the equipment is going to be cleaned, be sure to turn OFF the power of each
equipment, and unpulg the power cord from the AC outlet. Never use alcohol, benzine,
thinner or any other flammable cleaning agents.
Prohibited Othewise, it may result in fire or electric shock.
- Clean the plug of the power cord periodically by unplugging it from the AC outlet and
removing dust or dirt from the plug. Clean the peripherals and AC oulet with a dry cloth.
If the cord is kept plugged in for a long time in a dusty, humid or a sooty place, objects around the
plug will attract moisture, and this could cause insulation failure that could result in a fire.
- For safety reasons, be sure to turn OFF the power to each piece of equipment when the
inspections indicated in this manual are going to be performed.
Otherwise, electric shock may occur.
DRT-MAN-092 9
WARNING
Battery pack and charger
- Do not use the battery pack as a power source for equipment other than EVS 2430Wi detectors.
Be sure to use only the dedicated battery pack for the EVS 2430Wi detector.
- The battery charger is designed for the dedicated battery pack. Do not use the battery charger
other than the dedicated one. Otherwise, a battery explosion or a battery leak may occur,
resulting in fire or electrical shock.
- Do not operate the battery charger using any type of power supply other than the one indicated
on the rating label.
- Do not handle the product with wet hands.
- Do not attempt to disassemble, alter, or apply heat to the product.
- Avoid dropping or subjecting the product to severe impacts. To avoid the risk of injury, do not
touch the internal parts of the battery if it has been cracked.
- Stop using the battery pack immediately if it emits smoke, a strange smell, or otherwise behaves
abnormally.
- Do not let the battery pack and battery charger come into contact with water or other liquids and
do not allow them to get wet.
- Do not clean with substances containing organic solvents such as alcohol, benzene, thinner, or
other chemicals. Otherwise, fire or electrical shock may occur.
- Do not allow dirt or metal objects (such as hair pins, clips, staples or keys) to contact the
terminals. Otherwise, battery explosion or leakage of electrolyte may occur, resulting in fire,
injury or pollution of surrounding area. If the battery leaks and the electrolytes come into contact
with your eyes, mouth, skin or clothing, immediately wash it away with running water and seek
medical attention.
- Do not leave, store, or place the product in a location near heat sources, or in a place subject to
direct sunlight, high temperature, high humidity, excessive dust, or mechanical shock. Otherwise,
battery leakage, overheating or damage to the product may occur, resulting in electrical shock,
burns, injury or fire.
- Do not attempt to use a battery pack that has deteriorated. Using a battery pack that has
exceeded its life cycle may lead to overheating, fire or explosion.
- The Lithium ion/polymer battery is recyclable.
- Battery slowly discharges even if not in use.
- The useful battery life can expire if it discharges immediately after being fully charged. You can
purchase an optional battery pack to replace an exhausted one.
- The battery pack is a consumable item. If a fully charged battery is consumed quickly, use a new
and fully charged battery pack.
- Be sure to charge the battery periodically (once a year) if it is not used for an extended period of
time. The battery pack cannot be charged if it has been over discharged.
- Before discarding the battery pack, cover the terminals with adhesive tape or other insulators.
Contact with other metal materials may cause fire or explosion.
- Remove battery pack from equipment which is unused for a few minutes to prevent discharge .
DRT-MAN-092 10
WARNING
Installation and environment of use
- Do not install the equipment in any of the locations listed below. Doing so may result in
malfuction, equipment faillng, fire or injury.
ㆍ Close to facilities where water is used.
ㆍ Where it may be exposed to direct sunlight.
ㆍ Close to the air outlet of an air-conditioner or ventilation equipment.
ㆍ Close to a heat source such as a heater.
ㆍ Where the power supply is unstable.
ㆍ In a saline or sulfurous environment.
ㆍ Where temperature or humidity is high.
ㆍ Where there is freezing or condensation.
ㆍ In areas prone to vibration.
ㆍ On an inclined surface or in an unstable area.
- Because the equipment cable is long, take care that cables do not become tangled during
use. Also, be careful not to get your feet caught in the cable.
Otherwise, it may cause a malfunction of the equipment or injury of the user due to tripping over
the cable.
Power supply
- Always connect the three-core power cord plug to a grounded AC power outlet.
- To avoid the risk of electric shock, this equipment must only be connected to a power
supply that maintains protective earth”.
- To make it easy to disconnect the plug at any time, avoid putting any obstacles near the
outlet. Otherwise, it may not be possible to disconnect the plug in an emergency.
- Be sure to ground the equipment to an indoor grounded connector. Also, be sure to
connect all the earth connections for the system to a common ground.
- Do not use any power source other than the one provided with this equipment.
Otherwise, fire or electric shock may be caused due to leakage.
- The product has lower breaking capacity type. So do not intall at the building power
system prospective short-circuit current exceeding 35A
Handling
- Do not spill liquid or chemicals onto the equipment. In cases when the patient is injured,
do not allow liquid or chemicals to come in contact with blood or body fluids.
In such a situation, protect the equipment with a disposable covering as necessary.
- Turn OFF the power to each piece of equipment for safety when not being used.
DRT-MAN-092 11
CAUTION
Handling the equipment
The Equipment must be handled with care to avoid personal injury or damage to the internal image sensor.
- Handle the equipment carefully.

- Do not submerge the equipment in water.
- The internal image sensor may be damaged if something hits against it, or if it is
dropped, or recieves a strong jolt.
- Do not place excessive weight on the detector.

Otherwise, the internal image sensor may be damaged.
<Load Limit>
Uniform load: 150 kg over the whole Local load: 100 kg on an area
area of the detector of 40 mm in diameter
- Be sure to use the detector on a flat surface that does not bend.
Otherwise, the internal image sensor can be damaged.
- Be sure to securely hold the detector while using it in upright positions.
Otherwise, the detector may fall over, resulting in injury to the user or patient, or
may flip over, resulting in damage to the inner device.
DRT-MAN-092 12
1.2. Notes for using the equipment

When using the equipment, take the following precautions. Otherwise, problems may occur and the equipment may
not function correctly.
System Diagnostic
• The Ecali1 software runs a system diagnosis.
• Run Ecali1 software after installing the system, at least once a year. If an error occurs, report the detailed error
information to DRTECH local dealer or distributor.
The owner is responsible for ensuring that the system diagnostic is

CAUTION performed every year.
Do not try to use the system if the system diagnosis failed.
Calibration
• To ensure optimal performance of the system, it is important to verify that the system is calibrated.
• You can process calibration with the calibration data CD (provided).
The owner is responsible for ensuring that the system calibration is

performed whenever the system installation is completed or the system is
CAUTION repaired. Do not try to use the system if system calibration is not
performed.
Before exposure
• Be sure to check the equipment on a daily basis and confirm that it works properly.
• Suddenly heating the room in clod area will cause condensation to form on the equipment. In this case, wait until
the condensation evaproates before performing an exposure. If the equipment is used while the condensation
forms, problems may occur in the quality of captured images. When an air-conditioner is used, be sure to
raise/lower the temperature gradually so that a significant change in temperature in the room and in the
equipment does not occur, to prevent condensation.
DRT-MAN-092 13
During exposure
• Do not use the selected frequency chanel (2.4GHz and 5GHz dual band) for other wireless devices.
Mutual interference may affect the image data transmission rate.
• Do not use the detector near devices generating a strong magnetic field. Doing so may produce image noise or
artifacts.
Image Backup
• To avoid missing images which might result in patient being exposed to additional doses of radiation, it is
important to send the images to PACS or back up the images by filming or by using external storage devices
such as CD, DVD, HDD, USB, etc.. This should be done as a routine operation for every patient. If the hard disk
of your workstation is about to full, the operator should backup images and manually delete the images as
administrator to make room on the hard disk for new images.
User Limitation
• The Ecali1 software has the technician mode which could only be operated by inputting the correct PASSWORD.
The technician mode should be operated by the personnel who are qualified by DRTECH.
Electric Shock Hazards
• To reduce electric shock hazards, the system must be connected to an electrical ground.
• A three-contact conductor AC power cable is supplied with this system to provide the proper electrical grounding.
The power cable must be plugged into an UL-approved three-contact electrical outlet.
• Do not disassemble or modify the product as it may result in fire or electric There are no serviceable parts inside
equipments and adjustments should not be made. Only trained and qualified personnel should be permitted
access to the internal parts of the system.
• To reduce electric shock hazards, product is required to be well insulated with the use of appliance coupler, mains
plug, and other seperable connections.
DRT-MAN-092 14
Disinfection and cleaning
• Wipe it with a dry cloth slightly damed with a neutral detergent.
• Do not use solvents such as alcohol, thinner or benzene. Doing so may damge the surface of the equipment.
• Do not clean the system while the power is on.
Operating/storage environment
• Be sure to use and store this equipment under the conditions described below:
Temperature Humidity Atmospheric pressure
Operating environment 10 to 35 ℃ 30 to 85 % RH 700 to 1060 hPa
Transportation &
-10 to 40 ℃ 5 to 95 % RH 500 to 1060 hPa
Storage environment
• Do not expose this equipment to high temperatures and/or high humidity. Malfunction can occur.
• When not in use, keep the detector, handle unit, and grid in a designated location or in a location where they are
safe and cannot fall down.
Notes on disposal
• Disposal of this product in an unlawful manner may have a negative impact on health and on the environment.
Therefore, when disposing this product, be absolutely sure to follow the procedure which complies with the laws
and regulations applicable in your area.
• The expected life span of EVS 2430Wi system is about 3 years.
Handling the equipment
• The equipment must be handled with care to avoid personel injury or damage to the internal image sensor.
• The EVS 2430Wi Wireless is an advanced wireless digital radiographic equipment in the DRTECH Exprimer
series. This equipment is designed to provide the highest resolution and sensitivity in the series. In addition, the
wireless LAN (IEEE 802.11n*) communication feature improves the operability, and high-speed processing.
DRT-MAN-092 15
EVS 2430Wi User’s Manual 2. Introduction
2. Introduction
2.1. Features
• Wireless LAN communication (IEEE 802.11n*) includes a lightweight and thin detector that is easy to handle.
• The shape of the detector, which is identical to that of a conventional film cassette complying with ISO4090,
enables digital radiography to apply to the existing analog radiography configuration.
• The new sensor with 76 μm of pixel pitch and CsI (Cesium Iodide), Gadox (Gadolinium Oxysulfide) used for the
scintillator produces high resolution (approx. 11.8 Mega pixels) digital images within the effective imaging area
(223 x 291 mm), with low doses of X-rays.
• Depending on the operating conditions at each site, the wiring unit (optional) enables the equipment to be used
through expansion to a wired connection.
 At the time of installation, set a specific channel in the frequency band of 5.0 GHz before using the LAN.
Note that the available frequency band for this standard varies, depending on the local radio laws,
regulations and system requirements.

Intended Use
The EVS 2430Wi of Flat Panel Digital X-ray detector for industry was designed for industrial use.
Intended conditions of use
Considerations Condition
 Operating conditions
- Temperature: 10 ºC to +35 ºC
- Barometric Pressure: 700 hPa to 1060 hPa
- Humidity: 30 % R.H. to 85 % R.H.
 Storage and delivery conditions
- Temperature: -10 ºC to +40 ºC
Environment including hygienic requirements
- Barometric Pressure: 500 hPa to 1060 hPa
- Humidity: 5 % R.H. to 95 % R.H.
 Non-sterile
 Less than ten minute contact
 Ambient luminance range: 100 lx to 1500 lx
 Viewing angle: normal to the display ± 20°
DRT-MAN-092 16
2.2. System Configuration
2.2.1. Basic Configuration
Generally, the EVS 2430Wi detector is used in system configuration as illustrated below:
Figure 2.1 EVS 2430Wi System Configuration
DRT-MAN-092 17
Wireless Connection
• EVS 2430Wi wireless detector transmits images and data by wireless communication.
• A battery pack should be installed in the detector to use it under the wireless configuration.
• Up to 2 battery packs can be charged simultaneously from a battery charger.
- Use of multiple WLAN devices within the same frequency band may cause interference within
each wireless communication and slow down the transmission speed
- Do not cover or block the wireless module of the detector. Otherwise, the transmission speed or
operable distance may reduce.
- Recommended maximum operating distance of wireless communication, between the detector
and Access Point (AP), is 8 meters.
Wired Connection
• Connect EVS 2430Wi wireless detector and SSU / or Functional cable with a tether interface cable to make a
wired configuration.
• As the tether interface cable supplies power, a battery pack is not needed to be inserted in the detector.
The wired connection is more suitable for stabilized communication when the detector is set in a
bucky stand or on a table.

 enables the battery pack to be continously supplied with power while using the detector.
 drastically.
DRT-MAN-092 18
EVS 2430Wi Wireless system consists of detector, system synchronization unit (SSU), CDs and relevant accessories.
(Refer to chapter 3-1 “Product Components” for CD information)
Table 2.1. EVS 2430Wi Packaging
X-ray Detector Battery Charger Battery Pack

(EVS 2430Wi) (EVS-BCS) (EVS-MBP-Y)
Wireless Charging System Power adaptor (12V, 7.08A) LAN Card(PCIe Giga-bit LAN)
: Optional + AC Power Cable(2m) LAN Cable (CAT.7, 15m)
Access Point Tether Interface(3m) Functional cable (0.5 m)

(TP-LINK TL-WDR4300) : Optional + Power Adaptor: Optional
DRT-MAN-092 19
USB Switch Box Options

- USB Switch Box
- Hand Switch CD(Software / Calibration) User’s Manual (Hard Copy)
- USB Cable(1m)
- Generator Cable(1.2m)
DRT-MAN-092 20
EVS 2430Wi User’s Manual 3. Production Description
3. Product Description
3.1. Product Components
3.1.1. Auto Trigger Mode (AT Mode)
Table 3.1. Product componets for Auto Trigger Mode
Part name Remark
EVS 2430Wi(Scintillator : CsI : Tl) 1.9 kg

Flat panel detector
EVS 2430GWI(Scintillator : Gadox) 1.9 kg
Battery charger EVS-BCS : 0.5 kg
Battery pack EVS-MBP-Y : 0.24 kg
Wireless Charging System EVS-WPCS : 0.15 kg
Document : User ‘s Manual (PDF)

CD (Software / Calibration) Calibration Data : MAP, PMP, GMP
Software : Econsole1, Ecali1
User’s Manual Supported in all Modes
License Dongle Key (USB) Needed for activating Econsole1
Tether Interface Cable (3m) Supported in all Modes
LAN Cable (15m) Supported in all Modes
AC Power Cable (2m) Supported in all Modes
WARNING
The use of accessories and cables other than those specified, with the exception of EVS 2430Wi Wireless
accessories and cables sold by DRTECH Co., LTD. as replacement parts for internal components, may result in
increased emissions or decreased immunity of the equipment. Accessory equipment connected to the analog and
digital interfaces must be certified according to the respective IEC standards. All combinations of equipment must be
in compliance with IEC 60601-1-1 system requirements. Any person who connects additional equipment to the signal
input or signal output ports configures a medical system, and is therefore responsible for ensuring that the system
complies with the requirements of the system standard IEC 60601-1. If in doubt, consult DRTECH technical support
representative.
DRT-MAN-092 21
3.1.2. Synchronization Trigger Mode (Sync. Mode)
Table 3.2. Product componets for Synchronization Trigger Mode
Part name Remark

Flat panel detector

User’s Manual Supported in all Modes
License Dongle Key (USB) Needed for activating Econsole1
Generator Cable (15m) Supported in Sync. Mode
DRT-MAN-092 22
3.1.3. USB SW Mode
Table 3.3. Product componets for USB SW Mode
Part name Remark

Flat panel detector
EVS-USB01
USB Switch Box
Supported in USB Mode
User’s Manual Supported in all Mode
License Dongle Key (USB) Need for Econsole1
Hand Switch Supported USB Mode
Extension Tether Cable (7m) Supported in all Modes
USB Cable (1m) Supported in USB Mode
X-ray Cable (3m) Supported in USB Mode
DRT-MAN-092 23
3.1.4. Workstation (Recommended and minimum but NOT included)
Table 3.4. Workstation
Item Specification
Operating system Windows 7 64 bit SP1 (Professional Edition or higher)
CPU Intel Core i5 2600 or higher (or compatible CPU)
Memory 4GB or higher
Hard disk 1TB or higher
Gigabit (Detector only)

Intel® PRO 1000 Series (Gigabit LAN Card for network interface) Min.
Requirements : 1Gbps
LAN card
Jumbo Frames : 9K
Receive Descriptors : 2K (higher than 1024)
This is not dedicated to DICOM
Monitor 1024 x 768 or higher
Optional disc drive CD or DVD R/W
3.1.5. Grid (Recommended but Not included)
Table 3.5. Grid specifications
Item Description
SID 100 / 130 / 150 / 180 cm
Ratio 10 : 1
Frequency 125 Line/inch
Inter spacer Al
DRT-MAN-092 24
3.2. X-ray Imaging Condition
• X-ray Energy Range

40kVp to 150kVp
• Reliability (Lifetime Dose)

More than 74Gy (35uGy x 365days x 24hours x 60minutes x 60seconds/15sec)
DRT-MAN-092 25
EVS 2430Wi User’s Manual 4. Components and Specifications
4. Components and Specifications

4.1. Detector
4.1.1. Detector Specification
Table 4.1. Detector Specifications
Item Description
Model EVS 2430Wi / EVS 2430GWI
Purpose General Radiography
Pixel Pitch 76 ɥm
Scintillator CsI (Cesium Iodide) / Gadox (Gadolinium Oxysulfide)
Image Matrix Size 3072 × 3840 pixels
Effective Imaging Area (H x V) 233 x 291 mm
Image Acquisition and Transfer Time < 5 sec.
Spatial Resolution Min. 6.5 line pair/㎜

Powered by the battery pack
Rated Power Supply
(DRTECH Corporation(Powerlinx) / EVS-MBP-Y /7.4V, 4000
Wireless (Maker/Mode name/Rating)
mAh)
Wired (Maker/Model name/Rating)
Powered by Power adopter using tether interface
(XP Power / AHM85PS12 / DC12V 7.08A)
Power Consumption Max. 24 W
Network Interface Gigabit
Dimensions (㎜) [±0.5 mm] 267.5 (H) × 327.5 (V) × 14.9 (D)
Weight 1.8 kg
Environmental Requirements
Temperature: +10 to +35℃

Operational Humidity: 30 to 85% RH (Without Condensing)
Atmospheric pressure: 700 to 1060 hPa
Temperature: 0 to +40℃
Storage and Transportation(unpacked) Humidity: 10 to 90% (Without Condensing)
Atmospheric pressure: 500 to 1060 hPa
†Tether Interface:
Allows the detector to communicate with SSU via Ethernet cabling when wireless communications is not available or
when higher speed data transfer is necessary
DRT-MAN-092 26
4.1.2. Detector Component

The detector is designed to capture radiographic images.
Captured images are transmitted to the EVS 2430Wi image-capture computer using the wireless/wired data transfer
Figure 4.1. Detector Components
A. Wireless antena : Transmits image data with wireless comunication (IEEE802.11n).
B. Battery Pack : Supplies electrical power to the detector while using wireless communication
C. Satatus indicators
• Power : Shows power on/off status of the detector.
• Ready : Shows data communication status and ready status of detector
(Lights on indicates that detector is busy, lights off means detector is ready)
• Link : Shows detector’s registraion and connection status.
• AP : Lamp indicating Wired/ Wireless mode (2.4 GHz / 5 Hz)
D. AP Button: Can register detector among different wireless connection options.

(Connection options: Wireless using AP/ Wireless using detector’s internal AP/ Portable mode)
E. Power Button : Turns Detector on / off
F. Connecter : Data communication and power supplying through tether cable
G. Debugging Cover
H. WPCS Window : Wireless Charging Rx Window
Don’t remove G and H. if metal objects come into case, it can lead to
WARNING product malfunction..
The operator should not contact the inside of the access cover(G and H)
DRT-MAN-092 27
4.2. Battery Charger and Battery Pack and Adaptor

4.2.1. Battery Charger
4.2.1.1. Battery Charger Specifications
Table 4.2. Battery Charger Specifications
Item Description
Model EVS-BCS
Simultaneous Charging Battery Pack 2 EA
Charging Time 3 hours
Rated Power Supply DC +12 V, 6 A Max.
Dimensions (W x H x D) 180 mm x 255 mm x 35 mm
Weight 0.5 kg
4.2.1.2. Battery Charger Components
A D
Figure 4.2. Battery Charger
A. Power indicator : Indicates the power on/off status..
B. Charging indicator : Indicates the charging status.
C. Battery compartment : Insert the battery pack to charge.
D. DC Input : Connect the DC adapter to supply electrical power to the battery charger
DRT-MAN-092 28
4.2.2. Battery Pack
4.2.2.1. Battery Pack Specification
Table 4.3. Battery Charger Specifications
Item Description
Model EVS-MBP-Y
Cell Type Lithium Polymer
Number of Cells 2S1P (2series 1 Parallel)
Rated Power Supply Output : DC +7.4 V
Lifetime Approx. 500 cycles of use (full charge to discharge is 1 cycle)
Dimensions (W x H x D) 163 mm x 148 mm x 7 mm
Weight 0.24 kg
4.2.2.2. Battery Pack Components
Figure 4.3. Battery Pack
A. Charging indicator : Indicates the charging status
B. Latch knob : Rotate between on/off for battery swap
DRT-MAN-092 29
4.2.2.3. Charging Battery Pack

The battery pack supplies power to the detector during wireless connection.
Be sure to use only the dedicated battery pack, and fully charge it before usage.
• Connect the power adapter to the DC Input port of the battery charger. The power LED lights in blue indicates the
presence of direct current (DC) power.
• Insert the battery pack into the battery charger. Charging starts automatically. The charge LED lights appear
green when the battery pack is being charged. When battery pack is completely charged, all levels of chare LEDs
will illuminate.
• Gently pull the charged battery pack to remove from the battery charger.
Securely plug the power cord into the power source. If contact failure
WARNING occurs, or if dust or metal objects come into contact with the exposed metal
prongs of the plug, fire or electrical shock may occur.
Be sure to stop charging the battery pack when the charge LED lights
CAUTION appear in green beyond the specified charging time. Not doing so may result
in battery pack overheating or smoke emission, or battery explosion or fire.
You must use the power adaptor that is certified with IEC 60950 or IEC
CAUTION 60601-1.
Two batteries can be charged at the same time.
It takes approximately two hours to fully charge a battery pack. The required
charging time may vary depending on the temperature and remaining
battery level.
4.2.3. Adaptor
Table 4.3. AD/DC Adaptor Specifications
Item Description
Model AHM85PS12
Rated input 100- 240V / 1.0A, 50/60Hz
Rated output 12V, 7.08A
Maker XP POWER
DRT-MAN-092 30
4.3. Wireless Charging System

4.3.1. EVS-WPCS
4.3.1.1. EVS-WPCS Specifications
Table 4.4. EVS-WPCS Specifications

Item Description Note
Model EVS-WPCS
Dimensions (W x H x D) 115.8 mm x 94.8 mm x 12 mm
Weight 0.15 kg
Charging Transceiver IC Freescale MWTC1012 Medium Power
Charging Receiver IC Freescale MWPR1516 Medium Power
Tx Coil to Rx Coil 3mm
DC 12V (±1%) / more than 3A or
Input Voltage Adaptor (XP Power / AHM85PS12 / Tx Module Input
DC12V 7.08A)
Output Power DC 10V /1.4A (14W) Rx Module Output
Standby Current/Power 27.22mA / 326.6mW
Max Power Efficiency 83.2%
Storage Temperature -20℃ to 85℃
Operating Temperature 10℃ to 35℃
WPC Qi Specification WPC MP-A2 Standard.
H/W & S/W Protection Algorism.
4.3.1.2. EVS-WPCS Components
Figure 4.4. EVS-WPCS
DRT-MAN-092 31
1. EVS-WPCS Base
2. IRDA Window : IRDA comunication window.
3. Power Connection Cable
4. Debug Connector : for debuging
5. ID Switch : Deivce id setting dip switch.
6. Indicate LED Conntor : for cradle (Option)
7. Indicate LED Conntor : for system (Option)
4.3.1.3. TX / RX Module Specification
+ Tx Module + Rx Module
- PCB size : 55(mm)x45.5(mm) - PCB size : 65(mm)x47(mm)
- Coil size : 52.5(mm)x52.5(mm) - Coil size : 45.6(mm)x45.6(mm)
- Coil inductance : 11.7uH (MP A2) - Coil inductance : 7.3uH
4.3.1.4. RX Module Components
1. RX Module Base
2. Ferrite Sheet
3. Coil
4. IRDA : Communication for EVS-WPCS.
DRT-MAN-092 32
5. Connector : Power Output Connector.
4.3.1.5. EVS-WPCS Operations
EVS-WPCS variety of supports for the charging form.

• Cradle Charging Type
• Stand or Bed Bucky Charging Type
• Mobile Charging Type
WPCS Charging Emergency Charging
Cradle Carging
Charger
(Wall or Stand
Air State
(No Charging /
Using)
Tether Cable + Power Adaptor
Stand Charging
Mobile
Bed Table Charging
4.3.1.6. Attach Direction
DRT-MAN-092 33
4.3.1.7. Indicator LED Connector Description USER System EVS-WPCS
Num. Connector Name Remark

1 3.3V Power Out
2 Indicator Control 1
5 GND
4.3.1.8. Indicator LED Connector Description (Isolation)

4 GND
5 GND
DRT-MAN-092 34
EVS 2430Wi User’s Manual 5. Operating Procedure
5. Operating Procedure
General Workflow
The following workflow indicates the procedures after startup of EConsole1 and other system equipments
5-1. Preparing to use the detector
Attach a fully-charged battery pack to the detector.

1)
: A procedure in order to register the detector
to a specific digital radiography system
5-2. Operating the detector
2)
1. Turn on the detector : Network connection between the EVS 3643
wireless detector and the EConsole1
3)
:ㆍ Selection of EVS 3643 wireless
2. Register1) the detector and make connection2) to the from the Exprimer series detector
EConsole1 power supply to the detector ㆍ Selection of wireless/wired
data transfer
3. Conduct Examination
Loop back procedure

for each patient
ㆍSelect or register the patient information
ㆍSelect the protocol (selection3) of the detector)
- Arrange the patient in the correct posture

- Position the X-ray generator to adjust the
exposure field
- Check all the conditions
Loop back procedure

Check the captured images for each body part
ㆍ List the images
ㆍTransmit the images
Sterilize the portion of the detector that

has been in contact with a patient
ㆍConduct the next examination
5-3. Ending use of the detector
For details, refer to the

1. Turn off the detector operation manual or
setup guide of the
EConsole1
2. Remove the battery pack
DRT-MAN-092 35
5.1. Preparing to Use the Detector
Be sure to use only the dedicated power supply for the EVS-2430WI
CAUTION detector
5.1.1. Standard Configuration
Figure 5.1 EVS 2430Wi System Configuration
A. Wireless Connection
- EVS 2430Wi transmits images and data by wireless communication.
- A battery pack should be installed in the detector to use it under the wireless configuration.
- Up to 2 battery packs can be charged simultaneously from a battery charger.
B. Wired Connection
- Connect EVS 2430Wi and PC with a tether interface & Functional cable to make a wired
configuration.
- As the Functional cable supplies power, a battery pack is not needed to be installed in the
detector.
- Data communications are faster than wireless connection.
- It is able to keep charging a battery pack while using the detector.
DRT-MAN-092 36
5.1.2. Battery Pack
Securely attach the battery into the detector or charger. If contact failure
WARNING occurs, or if dust or metal objects come into contact with the exposed
connector pins of the detector or charger, fire or electrical shock may occur
5.1.2.1. How to Attach a Battery Pack
1) Align the arrows on the detector and battery pack.

2) Push down the battery pack.
3) Turn the battery lock knob 90 degrees clockwise.
5.1.2.2. How to Detach a Battery Pack
1) Turn the battery lock knob 90 degrees anti-clockwise.

2) Pull up the battery pack grabbing the knob.
Make sure to turn off the detector before detaching a battery pack. Press
WARNING and hold the power button for about 2 seconds. All status LED lamps turned
off indicates the detector is turned off.
DRT-MAN-092 37
5.1.2.3. How to Charge Battery Packs
5.1.2.3.1. Horizontal Direction
5.1.2.3.1.1. Attachment
1) Align the arrows on the charger and battery pack.

5.1.2.3.1.2. Detachment
1) Put the finger into the groove on the charger and grab the battery pack.
2) Pull up the battery pack.
DRT-MAN-092 38
5.1.2.3.2. Vertical Direction
5.1.2.3.2.1. Attaching
1) Stand the battery pack up to reveal the battery charged connector.

2) Align the left and right side of battery pack to the charger.
5.1.2.3.2.2. Detaching
1) Grab the battery pack.

2) Pull up the battery pack and push down the charger.
DRT-MAN-092 39
5.2. Hardware Installation

5.2.1. Connecting Device
This section describes how to connect the EVS 2430Wi system (Detector)
5.2.1.1. Operating AP
1) Connect the LAN cable to ethernet port (not internet) of AP, and the other to the LAN Card connector of
workstation assigned for the data transfer.
DRT-MAN-092 40
2) Connect the power cable to the power port of AP to supply power.
3) Turn on Wireless On/Off switch and push the Power button.
DRT-MAN-092 41
5.2.1.2. Functional Cable
This section describes how to connect the EVS 2430Wi system (Detector) without SSU by using functional cable.
Installation of this equipment should be made by licensed and authorized

CAUTION personnel.
LAN
Power
Tether
1) Connect the one of the functional cable to tether cable
Tether
Tether
DRT-MAN-092 42
2) Connect the LAN cable to the LAN Card connector of workstation assigned for the data transfer
3) Connect the power cable to other side of functional cable to supply power
DRT-MAN-092 43
5.2.2. Operating Detector

1) Turn on the detector
Before operating the detector, start up EConsole1
Press and hold the POWER button

(approx. 1 second )
Power lamp (Blue) lights up
2) Register the detector and make connection to the EVS control system
i. Registration
AP lamp (Green) blinks
When the AP lamp is blinking 1 time in 2seconds, system is in wired mode status.
When the AP lamp is blinking 2 times in 2seconds, system is in wireless mode (AP_1) status.
When the AP lamp is blinking 3 times in 2seconds, system is in wireless mode (AP_1) status.
When the AP lamp is blinking 4 times in 2seconds, system is in wireless mode (detector AP) status.
When the AP lamp is blinking 6 times in 2sec, system is in wireless mode (portable mode) status.
**User can set value of AP_1, AP_2, in Ecali Program. Please refer to Operation Manual for Ecali1
(Calibration tool).
ii. Connection
Network connection between the internal wireless

module of the detector and the wireless access
point/EVS control system is secured automatically.
The link lamp lights up when the detector is
registered and the communication connection is
established.
The LINK lamp does not light up when the detector is not registered or the communication connection is
not established.
When the READY and AP lamp is blinking and LINK lamp does not light up, a communication error has
occurred.
Please refer to troubleshooting.
DRT-MAN-092 44
3) Conducting Examination
For details about operation, refer to the Operation Manual for the EConsole1.
i. Select the patient information or protocols

on the screen and start the examination.
The READY lamp (green color) lights up after

blinking 3 times when the detector and
EConsole1 change to exposure ready status.
• Arrange the patient in the correct posture and position the detector aligning it with the target body part.
• Position the X-ray generator to adjust the exposure field.
• Check all conditions before exposure.
Make sure that two lamps (POWER and LINK) are lit and AP lamp is blinking. This means that the system
is ready to start an examination.
A communication error has occurred when LINK lamp lights are off.
When the READY lamp (orange color) blinks slowly, the detector is in detector selection status (Sleep).
The detector enters detector selection status automatically when it has not been used for a certain
period of time.
DRT-MAN-092 45
ii. Press the exposure switch of the X-ray

generator.
Images captured with the detector are
transmitted to the ECali1 and appear on
the monitor.
• Check the images on the monitor.

• If any uncompleted protocols remain,
repeat procedure ii).
• Choose the exposure mode before the shooting.
Mode Description
AED Auto Trigger Mode.
USB hand switch USB Switch Mode.
iii. Click the "Save Raw Image" button to store image.
• To conduct examination for another patient, repeat step iii.
Sterilize the portion of the detector that has been in contact with a patient to
IMPORTANT prevent infection
DRT-MAN-092 46
A signal strength indicator appears on the screen of the ECali1 computer. It shows the wireless
communication level between the detector and ECali1.
Keep the wireless communication level stable on capturing or transmitting images.
Table 5.1. Signal Strength Indicator

Signal Strength
Display Status Required Actions
(comunication stability)
Wireless, high
Normal
(Stable)
Wireless, Normal
Normal
(Stable)
Check whether there is any obstacle (e.q., your
hands) between the wireless module and the
Unstable wireless access point.
Wireless, Low communication.
If there is any obstacle, remove it.
(Unstable) Communication
speed is lowered If the problem cannot be resolved, ask for
consultation to your sales representative or local
DRTECH dealer.
Confirms that detector and the access point are
turned on.
No signal or No Link Disconnected
If the problem cannot be resolved, ask for
(Communication failed) communications
consultation to your sales representative or local
DRTECH dealer.
Wired Link Normal External cable connected.
Table 5.2. Power Mode Indicator
Display Power Mode Staus Required Actions
Active
Sleep Low power mode
Deep sleep Hibernation power mode only
Power turned off Disconnected

Power off
or not linked communications
DRT-MAN-092 47
Table 5.3. Battery Remains Indicator
Display Status Ext. Pwr Required Actions
Charge Ext. cable

complement & battery
Ext. cable Ext. cable
charging & battery
100% Only battery
90 to 99% Only battery
Warning message is popped up at the bottom-right.

Recommend to change the battery.
Warning message is popped up at the bottom-right.
Change the battery before the battery is discharged.
Change the battery.
No Battery or
Unkown If the problem cannot be resolved, ask for consultation to
Error
your sales representative or local DRTECH dealer.
DRT-MAN-092 48
5.2.3. Image Data Retransmission

EVS 2430Wi can save the image data as file when detector is disconnected from AP during image data transmission.
User can download the image file or receive the lastest shotted image data by using acquisition mode of EConsole1
after reconnection.
Figure 5.2. Flow Chart
If user does not use acquisition mode after reconnection, image data is saved as file. Image file cannot be
retransmitted automatically even if acquisition mode is activated.
For details about operation, refer to the Operation Manual for the EConsole1.
DRT-MAN-092 49
5.3. Ending Use of the Detector

• Turn off the detector
Press the POWER button.

All the LED lamps should be off.
Table5.4. Detector Status List
Power Ready Link AP

Lamp type
Lamp Lamp Lamp Lamp
Color ■ Blue ■ Green ■ Orange ■ Green ■ Green
Power ON ○ X X X X
During detector registration ○ X X X X
Detector registration completed (1 Sec.) ○ X X ○ ★
Communication established ○ X X ○ ★
During exposure preparation ○ X X ○ ★
Ready status or performing an

○ ☆/○ X ○ ★
examination (Ready)
During image data transmission ○ ○ X ○ ★
Sleep Mode ○ X ☆ ○ ★
Deep Sleep Mode ○ X ☆ ○ ★
Power OFF X X X X X
О : Light on ☆ : Blinking (On/Off status changes every second)

Х : Lights off ★ : Blinking slowly (On/Off status changes every 2 seconds)
- : Unspecified status
5.4. Detector Initialization

• Press the AP button for 20 to 25 seconds until AP LED lamp is blinking
• Detector will be connected again
• Setting the parameters of detector such as SSID, IP, etc.

Refer to "7.2.1. Detector Configuration".
DRT-MAN-092 50
EVS 2430Wi User’s Manual 6. Extension Facility
6. Extension Facility
6.1. X-ray Generator Interface
6.1.1. X-ray Exposure Mode
Table 6.1. Exposure Mode
Mode Description
1. The detector detects actual amount of X-rays without any connection to the X-ray
generator, and then performs image acquiring to the extent of image acquisition time
and transmits the image data.
Auto Trigger Mode (AT)
2. No signal used (No need of connector interface cable)
• You can use AT mode without connecting the generator with USB SW Box or SSU
physically.
1. The detector receives EXP_REQ signal that X-ray generator is prepared to generate
X-rays.
2. The detector prepares image acquiring and then responds EXP_OK signal to the X-
ray generator.
Sync. Trigger Mode
3. The X-ray generator confirms EXP_OK signal and generates X-ray, then the detector
performs image acquiring, according to image acquisition time and transmits the
image data.
• EXP_REQ (Generator→ Detector), EXP_OK (Detector →Generator)
1. EXP_IN signal generates by USB SW Box then the detector receives Ready signal.
And simultaneously, X-ray generator have ready status in
2. The detector prepares image acquiring
USB SW Mode 3. EXP_IN signal generates by USB SW Box and generates X-ray, then the detector
performs image acquiring, according to image acquisition time and transmits the
image data.
• Ready_IN (USB SW Box -> PC -> Detector and X-ray Generator)
• EXP_IN (USB SW Box -> PC -> Detector and X-ray Generator)
DRT-MAN-092 51
6.1.2. Auto Trigger(AT) Mode

AT Mode is available for acquiring images without any connection to X-ray generator. Generator interface cable is not
required
Figure 6.1. AT Mode Configuration
- Make sure to follow operating environment requirements (Temp.:10 to 35 oC)

- If you use AT Mode out of operating environmental requirements, unwanted image can be
acquired without x-ray image acquiring process.
- Do not hit or drop the equipment. Unwanted images can be acquired in the AT Mode if it
receives a strong jolt.
- If you image a thick object in the AT Mode with low X-ray tube voltage, an image may not be
acquired.
- AT performance is proportional to KV energy. Therefore, it is recommended to increase KV
CAUTION as much as possible and relatively decrease mA and ms.
- When you set x-ray exposure area towards the direction of the detector, the center block of
the detector should be included in the X-ray exposure area. Otherwise, you may not acquire
an image.
- The minimum X-ray exposure area should be wider than 4cm X 8cm on the center block of
detector.
DRT-MAN-092 52
6.1.2.1. Recommendation of setting AT Sensing Area
6.1.2.1.1. Stand Environment

We suggest the collimated area on detector is wider than 4cm X 8cm, and keep along the vertical direction as shown
in figure 6.2.
Figure 6.2 Stand Environment with AT Mode
6.1.2.1.2. Table Environment

We suggest the collimated area on detector is wider than 4cm X 8cm, and keep along the horizontal direction as
shown in figure 6.3
Figure 6.3. Stand Environment with AT Mode
DRT-MAN-092 53
6.1.3. USB SW Mode

USB SW Mode is the most common and recommended exposure mode at a retrofit scope. User can achieve high
quality images with USB SW Mode.
Figure 6.12. EVS 2430Wi USB Sw Mode Configuration
- The USB interface mode is a wired connection of wireless detector with SSU.
- PC and detector are connected by tether interface cable.
(consistent power supplying by adoptor).
- It is used in case when faster image transmission is needed, compared to a wireless connection.
- A wireless module in the detector is deactivated. (The equipped battery is not consumed)
- Connect the generator with USB SW Box physically to make an exposure in USB SW mode.
- You can use AT mode without connecting the generator with USB SW Box physically.
- Multiple detectors can be configured with one USB Box.
DRT-MAN-092 54
6.1.3.1. Wiring USB SW Mode
USB S/W Box
Adapter
(Optional)
Hand
Switch
1m
3m
X-Ray
Consol
e
Figure 6.13. Wiring USB Switch box
6.1.3.2. Connector Description
Figure 6.14. USB Switch box Connector
DRT-MAN-092 55
6.1.3.3. Connector Pin Assignment

1 PC USB RJ45-8Pin
2 XRAY_UNIT RJ11-4Pin
3 LED_BOX RJ11-6Pin
4 HAND SWITCH RJ11-4Pin
5 E-PWR (Adapter CON) DC5V/2A
6.1.3.4. X-ray_UNIT
Pin Num. Pin Name Remark

1 XRAY_RDY_COM * Dip SW Option
2 XRAY_EXP_GEN
3 XRAY_RDY_GEN
4 XRAY_EXP_COM * Dip SW Option
* XRAY_RDY_COM and XRAY_EXP_COM can be connected using dip switch.
It depends on x-ray generator.
6.1.3.5. Hand Switch

1 HAND_SW_RDY_COM GND
2 HAND_SW_RDY
3 HAND_SW_EXP
4 HAND_SW_EXP_COM GND
6.1.3.6. PC USB

1 VCC (+5V) -
2 RDY_IN -
3 LED_SW_CONTROL -
4 EXP_IN -
5 EXP_OUT -
6 GND -
7 - Not Connected
8 - Not Connected
DRT-MAN-092 56
6.2. Software Installation

This section gives information about how to install the software on the workstation (PC) and how to configure the
environment for software operation and communication.
6.2.1. Software Classification

DRTECH provides clients who purchase our detector system with software as shown below. User can choose and use
one of the software below.
Software Description
Image acquisition and adjustment software developed by DRTECH.

Econsole1
There is no need to develop separate software.
Ecali1 A configuration and management software for the detector
Document Econsole1 Operation Manual
Software development kit for EVS 2430Wi detector only, provided by DRTECH
EVS SDK
You can develop your own software dedicated to EVS 2430Wi by using this kit.
Document EVS 2430Wi SDK Developer’s Manual
6.2.2. Software Installation

• For a client who uses Econsole1, Install Econsole1 program after reading Econsole1 Operation Manual
carefully.
• For a client who uses EVS SDK, Install the Setup program after reading EVS SDK Developer’s Manual
Be sure to install the software first with perusing the manual,

CAUTION before configuring Windows environment.
DRT-MAN-092 57
6.3. Windows Environment Setting

This section gives information about configuring Windows to communicate with the detector.
The contents in this chapter are made on the basis of Windows 7.

Configuration environment can be different depending on network adaptor manufacturers or
models.
6.3.1. Network Communication
Communication disruption between the detector (Or SSU) and workstation occurs unless the
network adaptor is set properly. It may cause serious repercussion to the product and image
quality.
CAUTION
 Network Adaptor Selection
1) Click Start → Control Panel → Network and Internet → Network and Sharing Center → Change
Adapter Setting.
2) Choose the networks adaptor for communicating with the detector and SSU, and then rename it.
3) Click the chosen network adaptor with the right mouse button and click Properties to display the Properties
window.
DRT-MAN-092 58
 Network Adaptor Configuration
1) Click Configure button to open the following dialog box, and then go to the Advanced tab.
2) Choose Flow Control in the list of Properties and click Value button on the right.
3) Power-saving Mode on Network adaptor
- Click the Power Management tab and check on Allow the computer to turn off this device to save
power.
- Click OK button
DRT-MAN-092 59
4) Protocol selection and IP address setting
- Click Properties button after selecting Internet Protocol Version 4 (TCP/IPv4).
- Input the IP address and subnet mask as shown below, and then click OK button.
- It is recommended to set IP address and Subnet mask in the presented range of this
document.
- If you use IP address and Subnet mask out of the presented range, it would be difficult to
CAUTION identify the cause or resolve in case of communication disorder.
DRT-MAN-092 60
6.3.2. Disabling Sleep Mode on Monitor
1) Click Start → Control Panel → Power Options and then move to the Choose when to turn off the display
tab.
2) Set Put the computer to sleep to Never to disable the sleep mode.
3) Click Save changes button.
DRT-MAN-092 61
EVS 2430Wi User’s Manual 7. Device Setting
7. Device Setting
7.1. AP Setting
7.1.1. AP Configuration
Normally, AP setting does not need to be changed by user, because AP is set to match the use environment when the
product is inspected for shipping.
1) Check IP address of AP
- Enter the IP address of AP, as set in ECali1 (192.168.250.98).
- Choose Network tab → LAN. IP address can be seen as stored.
2) Setting wireless communication
- Choose Wireless 5GHz or 2.4GHz → Wireless Setting.
- Register wireless Network Name same with the detector, and select Region, Channel Width, Channel
depending on the use enviroment.
DRT-MAN-092 62
3) Setting wireless communication
- Choose Wireless 5GHz or 2.4GHz → Wireless Security
- Choose Disable Security and click the Save button
- Detector can not be connected to AP if security is enabled.
- Default IP Address of Detector is 192.168.250.135.

- 13 numbers of channel can be used in 2.4GHz Frequency.
- 8 numbers of channel can be used in 5GHz Frequency.
- Available channel will be limited according to country and region.
- Channel Bonding is for enhancing transmission speed. However, transmission speed may be
decreased due to channel’s interference, even if channel bonding has been done.
- Channel’s (+/-) will be activated in case of using 40MHz Frequency bandwidth.
- The configuration whether bonding with above channel or below channel can be done.
- AP's SSID should be same as Detector’s SSID, if user intends to use wireless communication.
DRT-MAN-092 63
7.2. Detecting Setting

7.2.1. Detector Configuration
For details about each parameter, refer to the Operation Manual for ECali1
Start up ECali1. Click Option → Configuration → Detector Tab.
Menu Description
Path to save map files Register each map file that corresponds to the product
Value for pre-processing.

Pre-processing
Do not change it by yourself.
Serial number Register the serial number of product.
IP address of AP.
Router IP
The detector can not be connected to AP if router IP is changed.
Grid selection Select type of the grid and register the path of grid filter.
Exposure mode Choose exposure mode
Wired/Wireless Choose communication mode
Image mode Select image mode
Waiting time for sleep mode can be adjusted by setting parameters below.
1) Acquisition sleep time
Power management Mode is changed from acquisition mode to sleep mode, after the set waiting time.
2) Deep sleep time
Mode is changed from sleep mode to deep sleep mode, after the set waiting time.
Hardware setting AP button on detector is activated if Enable AP Button is checked.
DRT-MAN-092 64
 Image TimeOut
Set the time limit to prevent re-transmission request.
Item Description
Time The set waiting time for image to be transmitted.
After starting image transmission, the detector ignores received information of image transmission request, if the
following conditions are all met.
- Image is being transmitted :

No interference is allowed during transmission.
- Transmission process is not completed :

After transmission, there is a slight waiting time for the transmission process to be finished.
 Deep Sleep Mode
Normal Detector can be operated and take an exposure at any time.
Sleep Detector can be operated and take an exposure at any time within 2 seconds.
Deep Sleep Detector can not be operated. User can take an exposure only if Deep Sleep Mode is canceled.
Power Off Detector has been turned off. User can take an exposure after detector is rebooted.
- You can prevent unnecessary battery consumption by using the Deep Sleep function.
- When SSU power is supplied to the detector by connecting a tether interface cable, the Deep Sleep function
cannot be operated.
- When using the Deep Sleep function, be sure to check if the detector is in Deep Sleep mode before making an
exposure. You cannot acquire images when the detector is in Deep Sleep mode.
- When the Deep Sleep mode is disabled, the detector needs maximum of 10seconds to wake up. It may not be
available to acquire images during this time.
DRT-MAN-092 65
7.2.2. Detector Power Save Management
 Meaning
Normal Detector can be operated and take an exposure at any time.
Sleep Detector can be operated and take an exposure at any time within 2 seconds.
Deep Sleep Detector can not be operated. User can take an exposure only if Deep Sleep Mode is canceled.
Power Off Detector has been turned off. User can take an exposure after detector is rebooted.
 Entry Condition for Power Save Mode
Mode Description
Normal -
Sleep Activates when the detector has not been used for a certain time.
Time can be set to automatically go into Deep Sleep mode, after a certain period of time passed
Deep Sleep
under sleep mode.
Detector is turned off if detector has not been used for a set period of time (Power off) from the
Power Off entry time of Deep Sleep Mode. However, in case of not using Deep Sleep mode function,
Detector is turned off if detector has not been used for certain time (Power Off After).
 Disabling Power Save Function
Mode Description
Normal -
Sleep Detector is in sleep mode.
Turn off Sleep Mode After setting time.

Deep Sleep
Call the function for turning off Deep Sleep Mode at SDK.
Power Off Reboot the detector with pressing power button on the detector.
DRT-MAN-092 66
 Other Information
Mode Initial Value Turnaround Time
Normal -
Sleep - Approx. 2 sec.
Deep Sleep OFF /10 min Approx. 10 sec.
Power Off OFF /60 min Approx. 40 sec.
- When using the Sleep function, be sure to check if the detector is in Sleep mode before
making an exposure. You cannot acquire images when the detector is in Sleep mode.
- When the Sleep mode is disabled, the detector needs max. 1 to 2 seconds to wake up. It
CAUTION may not be available to acquire images during this time.
DRT-MAN-092 67
EVS 2430Wi User’s Manual 8. Troubleshooting
8. Troubleshooting
8.1. Failed to Turn the Detector On
 Symptom
- Failed to turn on the power of the detector.
 Possible Causes
- Not installing battery pack well
- Dead battery pack
- Battery pack or Detector is broken
 Solutions
1) Install the battery pack.
2) Charge the battery pack.
3) Check the result after getting rid of the battery pack and connecting the tether interface cable.
4) Replace other battery packs and check the results.
5) Replace other Detectors and check the results.
6) Replace corresponding devices.
8.2. Errors in Detector LED
 Symptom
- Ready LED (Orange) lamps of detector are blinking 3 times/sec.
 Possible Cause
- Internal hardware errors of the detector
 Solutions
1) Consult with service engineers of DRTECH
DRT-MAN-092 68
8.3. The LINK LED does Not Turn on
 Symptom
- The LINK LED does not turn on when power LED is ON
 Possible Cause
- Detector registeration error
 Solutions
1) Check if AP is turned on.
2) Check if network cable is plugged to ethernet port of AP.
3) Check the network cable connection between workstation and AP.
4) Check the windows and network environment again such as firewall and IP address setting.
5) Check if the SSID of Detector is same as SSID of AP by using tether interface cable.
8.4. Rapid Consumption of Battery
 Symptom
- Consumption of a fully charged battery pack is fast.
 Possible Causes
- Performance decrease caused by usage of long time.
- Usage of battery pack in low temperature environment
 Solutions
1) Replace to new battery pack if the battery pack has been used for a long time. (Battery pack is a consumable)
2) Use battery pack in normal room temperature environment. Charging capacity of battery pack in low
temperature environment will decrease the capacity.
DRT-MAN-092 69
8.5. Battery Pack or Installation Part of Battery is Getting Hot
 Symptom
- Battery pack or compartment for installation of battery pack is getting hot.
 Possible Causes
- Battery pack failure
- Detector Failure
 Solutions
1) Do not use the battery pack
2) Consult with service engineers of DRTECH
8.6. The Power Switch of SSU or Status LED is not working
 Symptom
- The power switch of SSU is not working.
- The status LED of SSU is not responding.
 Possible Causes
- Power cable is broken down.
- Errors in the fuse
- Internal circuit is broken down.
 Solutions
1) Check the connection between AC power cable and SSU.
2) Replace the fuse.
DRT-MAN-092 70
EVS 2430Wi User’s Manual 9. Maintenance and Inspection
9. Maintenance and Inspection

In order to ensure that the equipment is used safely and normally, be sure to inspect the equipment before use. If any
problem is found during the inspection and cannot be corrected, please contact your sales representative or local
DRTECH dealer.
 Daily Inspection
For safety reasons, be sure to turn OFF the power to each piece of
WARNING equipment before the following procedures. Otherwise, an electric shock
may result.
 Cable
1) Ensure that cables are not damaged and cable jackets are not torn.
2) Ensure that the power cord plugs are securely connected to both the equipment AC inlet and the AC outlet.
 Detector
1) Ensure that there are no loose screws or broken parts.
2) Ensure that there is no dust or foreign substance on the external connector.
3) Ensure that there are no broken parts or short-circuits in the power supply conector.
 After turning on the power
Be sure to start ECali1 before performing the following inspection.
1) Perform test exposure.
 Monthly Inspection
1) Ensure that there are no loose screws or broken parts.
2) Ensure that there is no dust or foreign substance on the external connector.
 Yearly Inspection
1) Perform a Performance Test or Self-diagnosis using a phantom or resolution chart, etc.
 Irregular Inspection
 Calibration
1) Perform Calibration when exposure conditions have changed significantly.

For details, refer to the Setup Guide for ECali1.
DRT-MAN-092 71
EVS 2430Wi User’s Manual 10. Specification
10. Specification
10.1. Main Specifications
10.1.1. EVS 2430Wi / EVS 2430GWi X-ray Detector
[Dimensional Diagram] (Unit mm)
Figure 10.1 Detector Dimension
DRT-MAN-092 72
10.1.2. Battery Charger System
Figure 10.2 Battery Charger System Demension
DRT-MAN-092 73
10.1.3. Battery Pack
Figure 10.3 Battery Pack Demension
DRT-MAN-092 74
10.1.4. EVS-WPCS
Figure 10.4 EVS-WPCS Demension
DRT-MAN-092 75
10.2. Charateristics
 Typical Patient Doses
- Typical patient doses are equivalent to 500-1000 speed film/screen systems.
 Sensitometric Characteristics and Dynamic Range
- EVS 2430Wi Wireless responds linearly against the exposure range for 500-1000 speed film/screen where
it can depict the clinical information. It means that EVS 2430Wi fully covers a dynamic range of 0.2-20 μGy
at least.
 Spatial Resolution Properties
- EVS 2430Wi
A typical MTF value at 2 lp/mm, than 40%.
- EVS 2430GWI
A typical MTF value at 2 lp/mm, than 25%.
 DQE
- EVS 2430Wi
A typical DQE value at 1 lp/mm is 55%.
- EVS 2430GWI
A typical DQE value at 1 lp/mm, than 50%.
The product safety standards that apply to the EVS 2430Wi, which includes the following equipments, are as
below.
• Detector
• Battery Charger
• Battery Pack
• WPCS Module
• Wiring unit (sold separately, optional unit)
DRT-MAN-092 76
10.3. Packing
Note
Figures and Illustrations in this Technical Manual are provided for reference only and may differ from the actual
product appearance.
10.3.1. Product Configuration List
Table 10.1. EVS 2430Wi (Wireless) Supply Part List
No. Product Name Q'ty Remarks
1 TFT Detector Plate 1

2 Battery Charger 1
3 Battery Pack 2
4 Power Adaptor 1
5 AC Power Cable 1
6 Tether Cable
7 Functional Cable
8 LAN Cable 1
9 LAN Card 1
10 Access Point 1
11 Software CD 1
Table 10.2. Optional Product List
No. Product Name Q'ty Remarks
1 System Synchronization Unit (SSU)

2 AC Power Cable
3 Generator Interface Cable set
4 Adaptor Cable
5 USB Switch Box Set
6 Protection Case
7 Grid for Protection Case
8 Surface Pro 3
9 DROC S/W
10 Workstation
Note
If you find any items missing from the list above upon unpacking, please contact your dealer.
DRT-MAN-092 77
10.3.2. Assemble Package
Accessory Box Package

Accessory Box package
Cushion
Cushion
Detector Panel Package
EVS 2430Wi Package
Warning
Operational issues may occur if inappropriate force is applied to the product during unboxing. Please handle the box
containing the product with care.
Note
The packaging that came with the product should not be damaged or discarded as it is needed for after-sales service
or for exchanging the product with a new product. If the packaging or any component is missing, the damaged product
cannot be refunded or exchanged with a new product.
DRT-MAN-092 78
10.3.3. Detector Panel Package
Top cushion
PCM Pack
Inner form
600 Detector
PCM Pack
Bottom cushion
Detector panel Package
Note
• The PCM pack can explode from a hard impact or a contact with a sharp object.
• It is non-toxic and may not cause serious harm. However, please take extra precaution as it is a chemical
substance, and remember to carefully follow the instructions.
• If the inner chemicals get on your body, immediately wash it off thoroughly with clean water.
• If the inner chemicals get in your eyes, wash your eyes with tap water for more than 15 minutes and consult your
doctor.
• If the contents are accidentally ingested, drink two glasses of water (500ml) and consult your doctor.
• How to discard the content: Please discard used PCM packs using one of the following methods.
• Collect a certain number of packs and send them to the manufacturer.
• Treat them in a nearby chemical waste processing facility.
Note
• PCM Pack [Phase Change Material Pack]
• The PCM pack placed in the Bottom cushion is intended to maintain mild temperature over a certain period of time
in order to protect Detector from cold weather.
• The PCM is originally a liquid, and it begins to emit heat when the box is left for a long period at low temperature
below zero Celsius. Its phase changes to a solid state gradually during the heat radiation.
• The PCM is a reusable material, which means the solid state PCM returns to its liquid state within approximately 2
hours of heating over 35 degrees Celsius. Utilizing this method, the PCM can be used repeatedly.
• The liquid PCM should be stored around room temperature, and can be reused in the same way as the original
packing when any transportation is needed.
DRT-MAN-092 79
10.3.4. Component Box Assemble Package
10.3.4.1. AP Box Component
No Product Name Q'ty Remarks
1 Access Point 1
2 Tether Cable 1 Default
3 Functional Cable 1
4 USB Switch Box 1
5 USB Cable 1
Optional
6 Hand Switch 1
7 X-Ray Cable 1
10.3.4.2. Battery Box Component
No Product Name Q'ty Remarks
1 Battery Pack 2
2 Battery Charger 1
3 Software CD 1
4 Power Adaptor 1
Default
5 Power Code 1
6 LAN Card 1
7 LAN Cable 1
8 Adaptor Cable 1
DRT-MAN-092 80
EVS 2430Wi User’s Manual 11. Regulatory Information
11. Regulatory Information

11.1. Radio Frequency(RF) Compliance Information
 Declaration of Conformity
U.S.A. FCC Part 15 Subpart B Class A and Part 15 Subpart C (RF Exposure)
Canada RSS-210
1) For U.S.A. and Canada
• FCC/IC Compliance
This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions :
i. This device may not cause harmful interference.
ii. This device must accept any interference received, including interference that may cause undesired
operations.
• FCC ID
EVS 2430Wi : RNH-EVS2430WI
EVS WPCS : RNH-EVSWPCS
Note :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular Installation.
If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encourage to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet of a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.
DRT-MAN-092 81
• FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antennas or transmitters.
• RF Exposure Compliance
The available scientific evidence does not show that any health problems are associated with using low power
wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low
power wireless devices emit low levels radio frequency energy (RF) in the microwave range while being used.
Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does
not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures
have not found any biological effects. Some studies have suggested that some biological effects might occur,
but such findings have not been confirmed by additional research. EVS 2430Wi Wireless has been tested and
found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio
frequency (RF) Exposure rules.
• Disposal
Disposal of this product in an unlawful manner may have negative effects on health and on the environment.
When disposing this product, therefore, be absolutely sure to follow the procedure which is in conformity with
the laws and regulations applicable in your area.
The expected life span of EVS 2430Wi system is about 3 years.
DRT-MAN-092 82
11.2. Labels and Marking on the Equipment

The EVS 2430Wi detector and other components have labels and markings on them.
Their contents and locations are indicated below.
11.2.1. Detector
DRT-MAN-092 83
Detector Case
(257 x 336.5 x 14.9 mm)
< EVS 2430Wi Standard >
Detector Case
(257 x 336.5 x 14.9 mm)
< EVS 2430Wi Gadox Version >
DRT-MAN-092 84
11.2.2. Battery Charger and Battery Pack
11.2.2.1. Battery Charger
180 x 254.95 x 35.3 mm
11.2.2.2. Battery Pack
160.7 x 145.6 x 7.3 mm
DRT-MAN-092 85
11.2.3. EVS-WPCS
DRT-MAN-092 86
11.2.4. Symbol Description
Caution : Do not jolt or apply excessive load.
Non-ionized radiation
The Waste Electrical and Electronic Equipment Regulations indicates separate collection for
electrical and electronic equipments.
Certification mark that indicates the product complies UL 61010-1 (2012), CSA C22.2 No.
61010-1-12-CAN/CSA (2012) that specifies protection against fire, electric shock, and
mechanical hazards.
For U.S.A standards

Caution : Federal law restricts this device to sale by or on the order of a licensed practitioner.
For European Union (EEC Countries)
Hereby, DRTECH Corporation, declares that this EVS-2430WI Wireless is in compliance with
the essential equirements and other relevant provisions of Directive 1999/5/EC and
93/42/EEC. “0120” shows the notified body number for MDD.
MANUFACTUED Year and Month of production
(S/N) Serial number in six digits
This mark shows compliance with the equipment with R&TTE Directive 1999/5/EC
Protective Earth (Ground)
Direct Current
Alternating Current
Equipotentially.
Attention, refer to accompanying documents.
Stand-by
Read and understand all instructions and warning labels in the product documentation before
using the equipment.
Keep manual for future reference.
Product contains specific materials that are suitable for recycling.
Should be treated with care because if mistreated it might explode.
Keep away from fire and flames.
Heavy loading is prohibited.
Splashing of water
IPX4 This applies to EVS 2430Wi only.
DRT-MAN-092 87
11.3. Guidance and Manufacturer’s Declaration for EMC
Guidelines and Manufacturers : Electromagnetic emission
The EVS 2430Wi System is used in the following electromagnetic settings. Users of the EVS 2430Wi System should
check whether their systems are used in these settings.
Emission Test Compliance Electromagnetic Setting: Guidelines
Since the EVS 2430Wi System only uses RF energy for internal
RF emission
Group 1 functions, it has very low RF emissions and normally causes no
CISPR 11
interference to neighboring electronic devices.
RF emission
Class A
CISPR 11
The EVS 2430Wi System is suitable not only in non-household

Harmonic wave emission
Class A facilities but can also be used by directly connecting to the
CISPR 11
common low-power network in a building.
Voltage changes
/flicker emission Compliance
CISPR 11
DRT-MAN-092 88
Full Compliance to the IEC 60601-1-2:2007 and the System’s Tolerance to EM Waves
The EVS 2430Wi System is used in the following electromagnetic settings.
Users of the EVS 2430Wi System should check whether their systems are used in these settings.
IEC 60601 Electromagnetic Setting : Guidelines

Tolerance Test Suitability Level
Test Level
Static electricity The floor should be in wood, concrete or

+/- 6kV contact +/- 6kV contact
discharge (ESD) ceramic tiles. If the floor is in a synthetic
material, the relative humidity should be at
IEC 61000-4-2 +/- 8kV in the air +/- 8kV in the air
least 30%.
+/- 2kV power supply +/- 2kV power supply

Suitability in unit line unit line
electric over-sprays The main power’s quality should be equal to
general commercial or user settings.
IEC 61000-4-4 +/- 1kV input/ +/- 1kV input/
output line output line
Surge +/- 1kV line-line +/- 1kV line-line

The main power’s quality should be equal to
IEC 61000-4-11 general commercial or user settings.
+/- 2kV line-earth +/- 2kV line-earth
<5% UT <5% UT
(<95%Dip at the UT), (<95%Dip at the UT),
0.5 cycles 0.5 cycles The main power’s quality should be equal to
general commercial or user settings.
40% UT 40% UT
Voltage loss in the
(60% Dip at the UT), (60% Dip at the UT),
power supply, short Note :
5 cycles 5 cycles
intermittence and Most components in the EVS 2430Wi
voltage changes 70% UT 70% UT System have their power supplied from the
(30% Dip at the UT), (30% Dip at the UT), uninterrupted power supply.
IEC 61000-4-11
25 cycles 25 cycles
The IEC61000-4-11 only applies to the EVS
<5% UT <5% UT 2430WI System Power Box.
(>95% Dip at the UT), (>95% Dip at the UT),
5 seconds 5 seconds
Magnetic field in the

source frequency The magnetic field in the source frequency
(50/60Hz) 3A/m 3A/m should be equivalent to general commercial
or user settings.
IEC 61000-4-8
Note :
The UT is the main AC voltage before the test standards have been applied.
DRT-MAN-092 89
Guidelines and Manufacturers: Electromagnetic Tolerance
EVS 2430Wi System is used in the following electromagnetic settings.
Users of the EVS 2430Wi System should check whether their systems are used in these settings.
IEC 60601 Suitability

Tolerance Test Electromagnetic Setting: Guidelines
Test Level Level
When using a portable or a mobile RF communication

equipment, the recommended intervals, which have
been calculated using the equations, should be
maintained. These calculations should be made in
accordance with all of the EVS 2430Wi System’s parts
(including switches) and its transmitter-receiver’s
frequency.
Recommended intervals :
d = 1.17√p
d = 1.17√p80MHz to 800MHz
Conductive RF
3Vrms 150kHz-80MH 3Vrms d = 2.33√p800MHz to 2.5GHz,
IEC61000-4-6
Radioactive RF where p is the transmitter-receiver’s maximum power
3v/m 80MHz-2.5GHz 3v/m
IEC61000-4-3 rating in watts (W) and d is the recommended interval.
The magnetic field strength in the fixed RF receiver,

which has been determined in the EM wave
walkdown1, should be lower than the compliance
standards of each frequency range2.
Interference may occur around the equipment and is

expressed as the symbol shown below.
Note 1 :
The high-frequency range is applied at 80MHz to 800MHz.
Note 2 :
This guideline does not apply in all situations. Electromagnetic waves may be affected
through absorption and reflection from structures, objects and people.
DRT-MAN-092 90
Guidelines and Manufacturers: Electromagnetic Tolerance
It is very difficult to accurately predict the magnetic field strength of wireless (mobile/wireless) telephones, land
mobile radio base stations, amateur wireless channels, AM, FM wireless and TV broadcasting systems. To assess
electromagnetic settings using fixed RF receivers, area walk-down is needed. If the magnetic field strength
measured at the point, where the EVS 2430Wi System is used, exceeds the applicable RF compliance level, you
should check whether the EVS 2430Wi System is operating normally. If any performance abnormality is observed,
additional action may be needed such as changing the EVS 2430Wi System’s direction or location. At the frequency
range between 150kHz and 80MHz, the magnetic field strength should be less than 3v/m.
Recommended Intervals between the EVS 2430Wi System and the Portable
or Mobile RF Communications Equipment
The EVS 2430Wi System should be used in an electromagnetic setting where RF communication interferences are
controlled. Users of the EVS 2430Wi System should maintain the minimum intervals between the System and the
portable or mobile RF communications equipments to prevent electromagnetic interferences more effectively.
Maximum output power rating of the

Interval depending on the transceiver-receiver’s frequency meters
transceiver - receiver Watts
150kHz to 80MHz 80MHz to 800MHz 800MHz to 2.5GHz

d = 1.17√p d = 1.17√p d = 2.33√p
0.01 0.117 0.117 0.233
0.1 0.37 0.37 0.737
1 1.17 1.17 2.33
10 3.7 3.7 7.36
100 11.7 11.7 23.3
For maximum power voltages of receivers are not shown in the above list, the recommended interval, d(m), can be
calculated by using the equation used for the receiver’s frequency. The p is the transmitter-receiver’s maximum
power rating in watts (W).
Note 1 :
The high-frequency range is applied at 80MHz to 800MHz.
Note 2 :
This guideline does not apply in all situations. Electromagnetic waves may be affected through absorption and
reflection from structures, objects and people.
DRT-MAN-092 91
EVS 2430Wi User’s Manual 12. Warranty
12. Warranty
DRTECH Corporation warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of delivery. If any such product proves to be defective during this warranty period,
DRTECH Corporation at its options, will repair the defective product without charge for parts and labor, or will provide
a replacement in exchange for the defective product. In order to obtain service under this warranty, customer must
notify DRTECH Corporation of the defect before the expiration of the warranty period and make suitable arrangements
for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the
service center designated by DRTECH Corporation with shipping charges prepaid. DRTECH Corporation shall pay for
the return of the product to customer if the shipment is to a location within the country in which the DRTECH
Corporation designated service center is located. Customer shall be responsible for paying all shipping charges,
duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure, or damage caused by improper or inadequate maintenance and
care. DRTECH Corporation shall not be obligated to furnish service under this warranty to repair damage resulting
from attempts by personnel other than DRTECH Corporation or its representatives to install, repair, or service this
product, to repair damage resulting from improper use or connection to incompatible equipment or power source; or to
service a product that has been modified or integrated with other products when the effect of such modification or
integration increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY DRTECH Corporation WITH RESPECT TO THIS PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. DRTECH Corporation AND ITS VENDOR DISCLAIM ANY IMPLIED
WARRANTIES OF MERCHANTABLILITY OR FITNESS FOR A PARTICULAR PURPOSE. DRTECH Corporation
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE REMEDY PROVIDED TO
THE CUSTOMER FOR BREACH OF THIS WARRANTY. DRTECH AND ITS VENDORS WILL NOT BE LIABLE FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER
DRTECH Corporation OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
There are no warranties which extend beyond the description mentioned in this document.
DRT-MAN-092 92
 Revision History
Revision Date Descriptions
00 Feb.24.2017 Initial Release
DRT-MAN-092 93
DRTECH Corporation.
Suite No.2 3 Floor, 29
Dunchon-daero541beon -gil,
Jungwon-gu, Seongnam-si, Gyeonggi-do, Republic of Korea
Web Site : http://www.drtech.co.kr
Customer Support Team
E-mail : drtech@drtech.co.kr
Tel : +82 31 730 6805 / Fax : +82 31 730 6899
EXAMION GmbH
Erich-Hherion Stuttgart. 37 in 70736 Fellbach. Germany
DRT-MAN-092 94

DRTECH User Manual

Uploaded by

DRTECH User Manual

Uploaded by

DRTECH

EVS 2430Wi / EVS 2430GWi

Important information on usage and maintenance of equipment

1. Safety Information .................................................................................. 8

3. Product Description ............................................................................. 21

4. Components and Specifications ........................................................ 26

5. Operating Procedure ............................................................................ 35

5.2. Hardware Installation ................................................................................. 40

6. Extension Facility ................................................................................. 51

6.2. Software Installation .................................................................................. 57

7. Device Setting ........................................................................................ 62

9. Maintenance and Inspection ............................................................... 71

10. Specification ...................................................................................... 72

11. Regulatory Information.................................................................... 81

11.2.3. EVS-WPCS ......................................................................................................................................... 86

12. Warranty ............................................................................................. 92

This is used to indicate a prohibited operation.

This is used to indicate an action that must be performed.

This is used to indicate important operations and restrictions.

This is used to indicate operations for reference and complementary

- Securely plug the power cord into the AC outlet.

- No modification of this equipment is allowed

When a problem occurs

Maintenance and inspection

- Handle the equipment carefully.

- Do not place excessive weight on the detector.

1.2. Notes for using the equipment

• The Ecali1 software runs a system diagnosis.

The owner is responsible for ensuring that the system diagnostic is

• You can process calibration with the calibration data CD (provided).

The owner is responsible for ensuring that the system calibration is

Electric Shock Hazards

Disinfection and cleaning

• Wipe it with a dry cloth slightly damed with a neutral detergent.

• Do not clean the system while the power is on.

Temperature Humidity Atmospheric pressure

Operating environment 10 to 35 ℃ 30 to 85 % RH 700 to 1060 hPa

• The expected life span of EVS 2430Wi system is about 3 years.

Handling the equipment

Intended conditions of use

2.2. System Configuration

2.2.1. Basic Configuration

Figure 2.1 EVS 2430Wi System Configuration

• Up to 2 battery packs can be charged simultaneously from a battery charger.

Table 2.1. EVS 2430Wi Packaging

X-ray Detector Battery Charger Battery Pack

Access Point Tether Interface(3m) Functional cable (0.5 m)

USB Switch Box Options

Table 3.1. Product componets for Auto Trigger Mode

Part name Remark

EVS 2430Wi(Scintillator : CsI : Tl) 1.9 kg

Battery charger EVS-BCS : 0.5 kg

Battery pack EVS-MBP-Y : 0.24 kg

Wireless Charging System EVS-WPCS : 0.15 kg

Document : User ‘s Manual (PDF)

User’s Manual Supported in all Modes

License Dongle Key (USB) Needed for activating Econsole1

Tether Interface Cable (3m) Supported in all Modes

LAN Cable (15m) Supported in all Modes

AC Power Cable (2m) Supported in all Modes

3.1.2. Synchronization Trigger Mode (Sync. Mode)

Table 3.2. Product componets for Synchronization Trigger Mode

Part name Remark

EVS 2430Wi(Scintillator : CsI : Tl) 1.9 kg

Battery charger EVS-BCS : 0.5 kg

Battery pack EVS-MBP-Y : 0.24 kg

Wireless Charging System EVS-WPCS : 0.15 kg

User’s Manual Supported in all Modes

License Dongle Key (USB) Needed for activating Econsole1

Tether Interface Cable (3m) Supported in all Modes

LAN Cable (15m) Supported in all Modes

AC Power Cable (2m) Supported in all Modes

Generator Cable (15m) Supported in Sync. Mode

3.1.3. USB SW Mode

Table 3.3. Product componets for USB SW Mode

Part name Remark