Scribd
Upload
136 views8 pages

FPG APC TAG Typical Single Pile Pile Cap Materials: (F) (F) (C) (C)

This document provides design details for a reinforced concrete pile cap including materials, geometry, loadings, and design calculations. It specifies the concrete grade and steel properties, pile dimensions and capacities, and pile cap dimensions. It also includes the design of the bottom reinforcement considering load factors, pile eccentricity, and factored bending moment.

Uploaded by

Franklyn Genove
Copyright
© © All Rights Reserved
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
Download as xlsx, pdf, or txt
136 views8 pages

FPG APC TAG Typical Single Pile Pile Cap Materials: (F) (F) (C) (C)

This document provides design details for a reinforced concrete pile cap including materials, geometry, loadings, and design calculations. It specifies the concrete grade and steel properties, pile dimensions and capacities, and pile cap dimensions. It also includes the design of the bottom reinforcement considering load factors, pile eccentricity, and factored bending moment.

Uploaded by

Franklyn Genove
Copyright
© © All Rights Reserved
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
Download as xlsx, pdf, or txt
Download as xlsx, pdf, or txt
You are on page 1/ 8

CONCRETE STRUCTURES

EN 1992-1-1; 2004: PILE CAP DESIGN

Project : Prepared : FPG


Location : Reviewed : APC
Owner : Approved : TAG

Typical Single Pile Pile Cap ax


Materials
Concrete grade (fcu) : N/mm2
Steel yield strength (fy) : N/mm2
top and side cover (cst) : mm W cy
bottom cover (cb) : mm
cx

L
A. Pile Criteria
Pile
Nominal Pile size (D) : mm
Overhang from pile cap edge to pile face (ax) : mm
Overhang from pile cap edge to pile face (ay) : mm
Compressive Strength of pile (fcu,pile) : N/mm2
Area of pile (Apile) : mm2
Pile Capacity (per pile) (PC, pile) : kN
Pile Cap
Pile Cap Type : 1B
Length (L) : 0.00 mm L =
Width (W) : 0.00 mm W =
Thickness/ Height (H) : mm
Column Dimension
Column Width (cx) : mm
Column Depth (cy) : mm

B. Design Bottom Reinforcement


Load factor (fL) :
Allowable pile eccentricity (ecc.) : mm
Additional moment due to pile eccentricity (Madd) : 0 kN-m Madd =
Factored Total Moment (MU) : 0 kN-m MU =
Effective depth (d) : mm
Resistance Moment Factor (K) :
Lever arm factor (z) :
Categories of Bolted Connections
Design Parameters:
Bolts Class : 5.6
Steel Grade (connected parts) : S 275
Yield Strength of Bolts (fyb) : 300 Mpa Section 3, Part 3.1, Ta
Ultimate Tensile Strength of Bolts (fub) : 500 Mpa Section 3, Part 3.1, Ta
Bearing Strength of connected part (pbs) : 460 Mpa Section 6.3, Clause 6.
Tensile Strength of Bolts (pt) : 0 Mpa Section 6.3, Part 6.3.4
coefficient (standard dimension of holes) (kbs) : 0.7 Section 6.3, Clause 6.
0
Shear Resistance Section 3.6, Part 3.6.1

PS = pS A S

Shear strength of bolts (ps) : 300 Mpa Section 6.3, Part 6.3.1
Shear Area (As) : mm2 Section 6.3, Part 6.3.2
Shear Capacity (Ps) : 0 kN

Bearing Capacity Section 6.3, Part 6.3.3

Pbb = d tp pbb

Nominal diameter of bolt (d) : 1.6 mm


Bearing strength of bolts (pbb) 500 Mpa Section 6.3, Part 6.3.3
Thickness of the connected part (tp) : mm
Bearing Capacity (Pbb) : 0 kN
RETE STRUCTURES
; 2004: PILE CAP DESIGN

Ref.No. : _ _ _ _ _-ST-01
Date : 10-Sep-18
Rev.No. :

ay

(2 x ax) + D
(2 x ay) + D

(PC x ecc.) / 1000


fL x Madd
Section 3, Part 3.1, Table 3.1
Section 3, Part 3.1, Table 3.1
Section 6.3, Clause 6.3.3.3, Table 32
Section 6.3, Part 6.3.4, Table 34
Section 6.3, Clause 6.3.3.3
0

Section 6.3, Part 6.3.1


Section 6.3, Part 6.3.2, Table 30

Section 6.3, Part 6.3.3, Table 31


DESIGN OF REINFORCED CONCRETE (GRAVITY BEAM)
NSCP 2015

Project :
Location :
Girder Label :

Geometry and Material:

Material Data:
f'c = 20.7 MPa compressive strength
fy = 275 MPa yield strength (main bar)
fy (stirruops)
= 275 MPa yield strength (ties)
Section Data:
b = 250 mm beam width
d = 400 mm beam depth
clr. co = 40 mm cover
rebar ø= 20 mm main rebar diameter
rebar ø= 10 mm stirrups/ ties
L = 5 m beam length

Unfactored Loads (Moments):


Support "A" Midspan Support "B"
Dead Load Moments
Negative 41.00 kN-m kN-m 41.00
Postive kN-m 46.00 kN-m
Live Load Moments
Negative 10.00 kN-m kN-m 10.00
Positive kN-m 12.00 kN-m

Factored Loads (Moments):


Support "A" Midspan Support "B"
Negative 41.00 kN-m kN-m 41.00
Postive kN-m 46.00 kN-m

Schedule of Reinforced Concrete Girders (Main Longitudinal)


Section Longitudinal Reinforcements
Girder
Mark Bar Support "A"
Width Depth Loc Midspan
dia continuous
20 TB 2
B-1 250 400
20 BB

Moment Capacity (Mcap):


Support "A" Midspan Support "B"
Top 72.44 kN-m ok 72.44 kN-m ok 72.44 kN-m
Bottom 49.83 kN-m ok 72.44 kN-m ok 72.44 kN-m

Unfactored Loads (Shear):


Support 1m from Support
Dead Load Shear:
63.00 kN 63.00 kN
Live Load Shear:
63.00 kN 63.00 kN

Factored Load Shear (Analysis):


Support 1m from Support
49.83 kN 49.93 kN

Design Shear Vu at Support


Support 1m from Support
Vu = kN kN
Vc = kN kN
Vs = kN kN
S = mm mm
Smax = mm mm
Req'd. = mm mm

Scheddule of Reinforced Concrete Girders (Stirrups)


Section Stirrups/ Ties Spacing
Girder Bar Legs
Mark Width Depth dia No. Spacing No. Spacing

10 100
B-1 250 400 10 2 1 50
ok ok

Recommendation:
USE 1@ 50, 10@ 100, 4@ 200, rest @ 300 to C.L.
TY BEAM)

Support "B"

kN-m
kN-m

kN-m
kN-m

Support "B"
kN-m
kN-m

ments
Support "B"
discontinuous
ok
ok

ps/ Ties Spacing

No. Spacing Rest

4 200 300
ok ok ok

You might also like