RISC vs CISC

Submitted to: Submitted by:

Mrs. Priyanka Soni Krati Katyal
MCA 2nd Sem
 2

Topics Covered

•INTRODUCTION
•CISC ARCHITECTURE
•CHARACTERSTICS & PROPERTIES OF CISC
•ADVANTAGES & DISADVANTAGES OF CISC
• CISC INSTRUCTION EXAMPLE
•RISC ARCHITECTURE
•CHARACTERSTICS & PROPERTIES OF RISC
•ADVANTAGES & DISADVANTAGES OF RISC
•RISC INSTRUCTION EXAMPLE
•RISC 5 STAGE PIPELINING
•COMPARISON BETWEEN RISC & CISC PROCESSOR
 3
Introduction

•A processor is the logic circuitry that responds to and processes

the basic instructions that drive a computer.
•CPU instructions are numbers stored in memory.
•Instruction set is a set of instructions a programmer can give to a
machine to perform operations.
•The instructions are specific to CPU architecture.
•Basic operations: read instruction from memory, decode,
execute ,write back.
 4
Fundamentals

From the architecture point of view, the microprocessor chips can

be classified into two categories:

1. Complex Instruction Set Computers (CISC) and

2. Reduce Instruction Set Computers (RISC) .
 5

CISC: Complex Instruction Set Computers

History
•CISC existed close to the beginning of general computing.

•Since the earliest machines were programmed in assembly language

and memory was slow and expensive, IBM designed an instruction set to
allow early programmer to easily program a hundred complex instruction
rather than thousands of individual instructions.

•CISC was developed to make compiler development simpler. It shifts

most of the burden of generating machine instructions to the processor.

• For example, instead of having to make a compiler write long machine

instructions to calculate a square-root, a CISC processor would have a
built-in ability to do this.
 6

CISC Architecture
• Complex instruction set computing is a CPU design where
single instructions can execute several low-level operations (such
as a load from memory, an arithmetic operation, and a memory
store) or are capable of multi-step operations or addressing
modes within single instructions.

• Called “complex” because of the complex work performed per

instruction.

• Concept: Encode the intention directly.

• Eg:” add X and Y and put the result in Z” (for X,Y,Z memory
address)

• Problem: Some instruction take more time then others.

• Examples: x86, s390.

• Small number of general purpose registers

 7
cont….

• Computers typically use CISC while tablets, smartphones and other devices
use RISC.

• So, the higher efficiency of the RISC architecture makes it desirable in these
applications where cycles and power are usually in short supply.

• In CISC instructions are executed by microcode.

• A CISC instruction set typically includes many instructions

with different sizes and execution cycles, which makes CISC
instructions harder to pipeline.
 8

Characteristic of CISC Processors

•A CISC instruction can be thought to contain many different type of

instructions bundled into one simple instruction.
•A large number of instructions - typically from 100 to 250 instructions.
•Some instructions that perform specialized tasks and are used
infrequently.
•A large variety of addressing modes - typically 5 to 20 different modes.
•Variable-length instruction formats
•Instructions that manipulate operands in memory.
 9
Properties of a CISC Processor
1. Richer instruction set, some simple, some very complex.
2. Instructions generally take more than 1 clock to execute.
3. Instructions of a variable size.
4. Instructions is an interface with memory in multiple
mechanisms with complex addressing modes.
5. No pipelining.
6. Microcode control make CISC instruction set possible &
flexible.
7. Work well with simpler compiler.
 10
Advantage
• Microprogramming is as easy as assembly language to
implement, and much less expensive than hardwiring a control
unit.

• As each instruction became more capable, fewer instructions

could be used to implement a given task. This made more
efficient use of the relatively slow main memory.

• Because micro-program instruction sets can be written to match

the constructs of high-level languages, the compiler does not
have to be as complicated.
 11
Disadvantage
• Complex instructions are infrequently used by programmers and
compilers.

• Memory references, loads and stores, are slow and account for a
significant fraction of all instructions.

• Procedure and function calls are a major bottleneck

Passing arguments
Storing and retrieving values in registers.

• Instruction set & chip of new genration hardware become more complex
with each generation of computers.
 12
CISC Instruction Example

A CISC could multiply 5 by 10 as follows:

Mov ax,10
Mov bx,5
Mul bx
 13

RISC: Reduced Instruction Set Computer

History
The first RISC projects came from IBM, Stanford, and UC-Berkeley in the
late 70s and early 80s.

The IBM 801, Stanford MIPS, and Berkeley RISC 1 and 2 were all
designed with a similar philosophy which has become known as RISC .

When designers create a new generation of processors, improving

performance is the key goal. There are three main factors that affect
performance; they are :
• How fast you can crank up the clock.
• How much work you can do per cycle.
• How many instructions you need to perform a task.
 14

RISC Architecture

• Called “reduced” because of the reduction of work performed by an

instructions.
• It is a type of microprocessor architecture that utilizes a small, highly-
optimized set of instructions, rather than a more specialized set of
instructions often found in other types of architectures.
• RISC's original goals was to limit the number of instructions on the chip
so that each could be allocated enough transistors to make it execute
in one cycle.
• Small set of instructions of a typical RISC processor consists mostly of
register-to-register operations, with only simple load and store
operations for memory access.
.
 15
cont….
• Thus each operand is brought into a processor register with
a load instruction
• All computations are done among the data stored in
processor registers.

• Results are transferred to memory by means of store

instructions.
• Concepts: Break operation into simpler sub operation.
• Eg: instruction: load X, load Y, add X and Y, store Z
 16

Characteristic of RISC Processors

• Simplifies the instruction set..

• The use of only a few addressing modes results from the fact
that almost all instructions have simple register addressing.

• Other addressing modes may be included, such as immediate

operands.

• By using a relatively simple instruction format, the instruction

length can be fixed and aligned on word boundaries.
• An important aspect of RISC instruction format is that it is easy
to decode.

• Shorter Instructions - Breaking the complex instruction into

several short simpler instructions
 17
cont….

• It has the ability to execute one instruction per clock cycle.

 This is done by overlapping the fetch, decode and execute
phases of two or three instructions by using a procedure referred to
as pipelining.
• The advantage of register storage as opposed to memory storage
is that registers can transfer information to other registers much
faster than the transfer of information to and from memory.
• Relatively few instructions
• Relatively few addressing modes.
• Memory access limited to load and store instructions
• Can run several instructions simultaneously.
 18
Properties of a RISC Processor
1. Simple primitive instructions and addressing modes.

2. Instructions execute in one clock cycle.

3. Uniformed length instructions and fixed instruction format.
4. Instructions interface with memory via fixed
mechanisms(load/store).

5. Pipelining.
6. Hardwired control.
7. Complexity pushed to the compiler.
 19
Advantage

• Speed: RISC processors often achieve 2 to 4 times the

performance of CISC processors using comparable
semiconductor technology and the same clock rates.

• Simpler hardware. Because the instruction set of a RISC

processor is so simple, it uses up much less chip space and
simple hardware requirements.

• Shorter design cycle. Since RISC processors are simpler than

corresponding CISC processors, they can be designed more
quickly, and can complete there work in 1 clock cycle
 20
Disadvantage
• Code Quality: The performance of a RISC processor depends greatly
on the code that it is executing. If the programmer (or compiler) does a
poor job of instruction scheduling, the processor can spend quite a bit of
time stalling: waiting for the result of one instruction before it can
proceed with a subsequent instruction.
• Code expansion: Since CISC machines perform complex actions with
a single instruction, where RISC machines may require multiple
instructions for the same action, code expansion can be a problem.
• System Design: Another problem that faces RISC machines is that
they require very fast memory systems to feed them instructions. RISC-
based systems typically contain large memory caches, usually on the
chip itself. This is known as a first-level cache.
 21
RISC Instruction Example

• In RISC the microprocessor's designers might make sure that add

executes in one clock.
• Then a compiler could multiply a and b by adding a to itself b times
or b to itself a times.

Mov ax,0
Mov bx,10
Mov cx,5
Begin:
Add ax,bx
Loop Begin
loop cx times
 22

RISC 5 Stage Pipeling

• Fivestage “RISC” load-‐ store architecture

1. Instruction fetch (IF)

• Get instruction from memory, increment PC.

2. Instruction Decode (ID)

• Translate opcode into control signals and read registers.

3. Execute (EX)
• Perform ALU operation, compute jump/branch target

4. Memory (MEM)
• Access memory if needed

5. Writeback (WB)
• Update register file
 23

RISC 5 Stage Pipeling

 24
Comparisons between CISC and RISC
Processors
• Instructions utilize more cycles than RISC.
• CISC has way more complex instructions than RISC.
• CISC typically has fewer instructions than RISC.
• CISC implementations tend to be slower than RISC
implementations.
• RISC design is approximately twice as cost-effective as CISC.
• RISC architectures are designed for a good cost/performance,
whereas CISC architectures are designed for a good
performance on slow memories.
 25
cont….
CISC RISC
Emphasis on hardware Emphasis on software

Includes multi-clock, Single-clock, reduced instruction

complex instructions only
Memory-to-memory: Register to register:
"LOAD" and "STORE" "LOAD" and "STORE"
incorporated in instructions are independent instructions

Slower since instruction can take Faster since instructions usually

more than 1 cycle take 1 instruction cycle

Main objective is less code. Main objective is speed.

 26
cont….
CISC RISC
More software oriented since the
compiler deals with
More hardware oriented.
translations.

Instruction size is mostly varied Instruction size is always a set

in size. size.

Addressing Modes can be

Addressing Modes are simple.
complex
 27

Examples of CISC and RISC Processors

 28
Comparisons between CISC and RISC
Instructions
• Lets consider a simple example: addition of x and y
 RISC Reduced Instruction Set Computers
– Break Operation into Simple Sub-Operation.
Load X,
Load Y,
add X and Y,
Store Z
 CISC Complex Instruction Set Computers
– Encode the Instruction Directly
Add X & Y Put the Result in Z.
29
 30
Reference

• www.google.com
• www.wikipidea.com
• www.youtube.com
• Andrew S.Tanenbaum
MLSU UNIVERSITY