Tender Document: SPAB/Advt.

/2016-17/RGO/11 Section-6: Bill of Quantity

Section-6
Bill of Quantities for works (BOQ)

A. A. Preamble
1. The Bill of Quantities shall be read in conjunction with the Instruction to Bidders, General and
Special Conditions of Contract, Technical Specifications and Drawings.
2. The quantities given in the Bill of Quantities are approximate and provisional, which are given
to provide a common basis for making payment for works. Actual quantities of work are likely
to increase or decrease as per the requirement at site. Hence there is no claim for any additional
or less quantities than the specified in the BOQ.
3. The rates in the Bill of Quantities shall, except insofar as it is otherwise provided under the
Contract, include all construction plant, labour, supervision, materials, erection, transportation,
maintenance, insurance, administrative overheads, profit, taxes and duties, together with all
general risks, liabilities and obligations set out or implied in the Contract.
4. The Bidder shall indicate the unit rate and line total on the Total Estimate Bid Amount, which
shall be applicable on each item of the Bill of Quantities, whether quantities are stated or not.
5. General directions and description of work and materials are not necessarily repeated nor
summarized in the Bill of Quantities. The whole cost of complying with the provisions of the
Contract shall be included in the items provided in the Bill of Quantities. References to the
relevant sections of the contract documentation shall be made before entering prices against
each item in the Bill of Quantities.

SPA Bhopal,

Contractor 34 SPA Bhopal

Institute Works Department, SPA BHOPAL
 Tender Document: SPAB/Advt./2016-17/RGO/11 Section-6: Bill of Quantity

Name of work: Aluminium partition & Vertical Blinds work in Quality Improvement Program (QIP) Centre at SPA Bhopal at Bhauri.

S.No DSR NO Description Unit QTY Rate Amount

1 21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with
extruded built up standard tubular sections/ appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia
and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with
required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust
free,straight,mitred and jointed mechanically wherever required including cleat angle, kg 900
Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all
complete as per architectural drawings and the directions of Engineer-in-charge.
(Glazing,paneling and dash fasteners to be paid for separately) :
For fixed portion Powder coated aluminium (Powder coated aluminium (minimum thickness
of powder coating 50 micron)
2 21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots
and making provision for fixing of fittings wherever required including the cost of EPDM
rubber /neoprene gasket required (Fittings shall be paid for separately) Powder coated kg 82
aluminium (minimum thickness of powder
coating 50 micron)
3 21.2.2 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or
graded wood particle board conforming to IS: 12823 Gradel Type ll, in panelling fixed in
aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel Sqm 113
screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-
laminated particle board with decorative lamination on both sides.
4 modify Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions
21.3.2 etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and
the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic sqm 44
item): With float glass panes of 5.0 mm thickness
5 21.13 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors
including necessary cutting and making good etc. Each 4
complete.
6 9.97.3 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less
than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with Each 4
necessary screws etc. complete : 200x10 mm
7 9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than
grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary Each 8
screws etc. complete:125 mm
8 9.101.2 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and Each 4
shade, with necessary screws etc. complete. Twin rubber stopper.
9 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door
closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to
Each 4
80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with
necessary accessories and screws etc. complete.
10 21.17 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required
shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved
design/pattern, with approved standard section and fixed to the existing window frame with
C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to kg 2
proper opening size for fixing and operation of handles and fixing approved anodised
aluminium standard section around the opening, all complete as per requirement and
direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
11 MR Providing & fixing vertical blinds of approved make in all colour & shade including all
necessary accessories complete etc. (Sample got to be approved by competent authority). Sqm 78
Make - (Mac, Decore, Classic - Vista, Wind Sam or equivalent)
TOTAL (in figures)

TOTAL (in words) ………………………………………………………………………………………………………………………………………………

Note: The rate and amount for above mentioned work has to be submitted in the financial bid only (and not in the technical bid), otherwise
the bid will be disqualified from participation in the financial bid.

Contractor 35 SPA Bhopal

Institute Works Department, SPA BHOPAL