Keystone Architecture

DDR3 Memory Controller

User's Guide

Literature Number: SPRUGV8E

November 2010 – Revised January 2015
 Contents

Preface....................................................................................................................................... 11
1 Introduction ....................................................................................................................... 13
1.1 Purpose of the Peripheral ................................................................................................. 14
1.2 Features ..................................................................................................................... 14
1.3 Industry Standard(s) Compliance Statement ........................................................................... 14
2 Peripheral Architecture ....................................................................................................... 16
2.1 Clock Interface .............................................................................................................. 17
2.2 SDRAM Memory Map ..................................................................................................... 17
2.3 Signal Descriptions ......................................................................................................... 17
2.4 Protocol Descriptions ...................................................................................................... 18
2.4.1 Mode Register Set (MRS or EMRS) ............................................................................ 19
2.4.2 Refresh Mode ...................................................................................................... 20
2.4.3 Activation ........................................................................................................... 20
2.4.4 Deactivation ........................................................................................................ 20
2.4.5 READ Command .................................................................................................. 20
2.4.6 Write (WR) Command ............................................................................................ 21
2.5 Address Mapping ........................................................................................................... 22
2.6 DDR3 Memory Controller Interface ...................................................................................... 27
2.6.1 Arbitration .......................................................................................................... 28
2.6.2 Command Starvation ............................................................................................. 29
2.6.3 Possible Race Condition ......................................................................................... 29
2.6.4 Class of Service ................................................................................................... 29
2.7 Refresh Scheduling ........................................................................................................ 30
2.8 Self-Refresh Mode ......................................................................................................... 30
2.8.1 Extended Temperature Range .................................................................................. 31
2.9 Reset Considerations ...................................................................................................... 31
2.10 Turnaround Time ........................................................................................................... 32
2.11 DDR3 SDRAM Memory Initialization .................................................................................... 32
2.11.1 DDR3 Initialization Sequence .................................................................................. 34
2.12 Dual Rank Support ......................................................................................................... 34
2.13 Leveling ...................................................................................................................... 34
2.13.1 Full Leveling (Auto Leveling) ................................................................................... 34
2.13.2 Incremental Leveling ............................................................................................. 35
2.13.2.1 Ramp Incremental Leveling................................................................................ 36
2.13.3 Impact On Bandwidth ............................................................................................ 36
2.13.4 Programming Full Leveling ..................................................................................... 36
2.13.4.1 Leveling Timeout ............................................................................................ 37
2.13.4.2 Read Data Eye Training Errata For Full Leveling ...................................................... 37
2.13.5 Programming Incremental Leveling ............................................................................ 38
2.13.5.1 Standalone Incremental Leveling ......................................................................... 38
2.13.6 Programming Ratio Forced Leveling .......................................................................... 38
2.13.7 Using Invert Clock Out........................................................................................... 38
2.14 Interrupt Support ........................................................................................................... 39
2.15 EDMA Event Support ...................................................................................................... 39
2.16 Emulation Considerations ................................................................................................. 39

2 Contents SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com

2.17 ECC .......................................................................................................................... 39

2.18 Power Management........................................................................................................ 40
2.18.1 SDRAM Self-Refresh Mode ..................................................................................... 40
2.18.2 SDRAM Power-Down Mode .................................................................................... 40
2.19 Performance Monitoring ................................................................................................... 40
3 Using the DDR3 Memory Controller ...................................................................................... 43
3.1 Connecting the DDR3 Memory Controller to DDR3 SDRAM ......................................................... 44
3.2 Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM Specifications......................... 48
3.2.1 Programming the SDRAM Configuration Register (SDCFG) ................................................ 48
3.2.2 Programming the SDRAM Refresh Control Register (SDRFC) ............................................. 48
3.2.3 Configuring SDRAM Timing Registers (SDTIM1, SDTIM2, SDTIM3, SDTIM4) .......................... 49
3.2.4 Configuring Leveling Registers .................................................................................. 50
3.2.5 Configuring Read Latency ....................................................................................... 50
4 DDR3 Memory Controller Registers ...................................................................................... 52
4.1 Module ID and Revision Register (MIDR) ............................................................................... 55
4.2 DDR3 Memory Controller Status Register (STATUS) ................................................................. 56
4.3 SDRAM Configuration Register (SDCFG) .............................................................................. 57
4.4 SDRAM Refresh Control Register (SDRFC)............................................................................ 59
4.5 SDRAM Timing 1 (SDTIM1) Register ................................................................................... 60
4.6 SDRAM Timing 2 (SDTIM2) Register ................................................................................... 61
4.7 SDRAM Timing 3 (SDTIM3) Register ................................................................................... 62
4.8 Power Management Control Register (PMCTL) ....................................................................... 63
4.9 VBUSM Configuration Register (VBUSM_CONFIG) .................................................................. 65
4.10 Performance Counter 1 Register (PERF_CNT_1) ..................................................................... 66
4.11 Performance Counter 2 Register (PERF_CNT_2) ..................................................................... 67
4.12 Performance Counter Config Register (PERF_CNT_CFG) .......................................................... 68
4.13 Performance Counter Master Region Select Register (PERF_CNT_SEL) ......................................... 69
4.14 Performance Counter Time Register (PERF_CNT_TIM) ............................................................. 70
4.15 Interrupt Raw Status Register (IRQSTATUS_RAW_SYS) ........................................................... 71
4.16 Interrupt Status Register (IRQSTATUS_ SYS) ......................................................................... 72
4.17 Interrupt Enable Set Register (IRQSTATUS_ SET_SYS) ............................................................ 73
4.18 Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS) .......................................................... 74
4.19 SDRAM Output Impedance Calibration Configuration Register (ZQCFG).......................................... 75
4.20 Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN) .......................................... 77
4.21 Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL).......................................... 78
4.22 Read-Write Leveling Control Register (RDWR_LVL_CTRL) ......................................................... 79
4.23 DDR PHY Control 1 Register (DDR_PHY_CTRL_1) .................................................................. 80
4.24 Priority to Class-Of-Service Mapping Register (PRI_COS_MAP) ................................................... 81
4.25 Master ID to Class-Of-Service 1 Mapping Register (MSTID_COS_1_MAP) ....................................... 82
4.26 Master ID to Class-Of-Service 2 Mapping Register (MSTID_COS_2_MAP) ....................................... 83
4.27 ECC Control Register (ECCCTL) ........................................................................................ 84
4.28 ECC Address Range 1 Register (ECCADDR1) ........................................................................ 85
4.29 ECC Address Range 2 Register (ECCADDR2) ........................................................................ 86
4.30 Read Write Execution Threshold Register (RWTHRESH) ............................................................ 87
4.31 DDR3 Configuration 0 Register (DDR3_CONFIG_0) ................................................................. 88
4.32 DDR3 Configuration 1 Register (DDR3_CONFIG_1) ................................................................. 89
4.33 DDR3 Configuration 2 Register (DDR3_CONFIG_2) ................................................................. 89
4.34 DDR3 Configuration 3 Register (DDR3_CONFIG_3) ................................................................. 90
4.35 DDR3 Configuration 4 Register (DDR3_CONFIG_4) ................................................................. 90
4.36 DDR3 Configuration 5 Register (DDR3_CONFIG_5) ................................................................. 91
4.37 DDR3 Configuration 6 Register (DDR3_CONFIG_6) ................................................................. 91
4.38 DDR3 Configuration 7 Register (DDR3_CONFIG_7) ................................................................. 92
4.39 DDR3 Configuration 8 Register (DDR3_CONFIG_8) ................................................................. 92

SPRUGV8E – November 2010 – Revised January 2015 Contents 3

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 www.ti.com

4.40 DDR3 Configuration 9 Register (DDR3_CONFIG_9) ................................................................. 93

4.41 DDR3 Configuration 10 Register (DDR3_CONFIG_10) .............................................................. 93
4.42 DDR3 Configuration 12 Register (DDR3_CONFIG_12) .............................................................. 94
4.43 DDR3 Configuration 14 Register (DDR3_CONFIG_14) .............................................................. 94
4.44 DDR3 Configuration 15 Register (DDR3_CONFIG_15) .............................................................. 95
4.45 DDR3 Configuration 16 Register (DDR3_CONFIG_16) .............................................................. 95
4.46 DDR3 Configuration 17 Register (DDR3_CONFIG_17) .............................................................. 96
4.47 DDR3 Configuration 18 Register (DDR3_CONFIG_18) .............................................................. 96
4.48 DDR3 Configuration 19 Register (DDR3_CONFIG_19) .............................................................. 97
4.49 DDR3 Configuration 20 Register (DDR3_CONFIG_20) .............................................................. 97
4.50 DDR3 Configuration 21 Register (DDR3_CONFIG_21) .............................................................. 98
4.51 DDR3 Configuration 22 Register (DDR3_CONFIG_22) .............................................................. 98
4.52 DDR3 Configuration 23 Register (DDR3_CONFIG_23) .............................................................. 99
4.53 DDR3 Configuration 24 Register (DDR3_CONFIG_24) .............................................................. 99
4.54 DDR3 Configuration 25 Register (DDR3_CONFIG_25) ............................................................. 100
4.55 DDR3 Configuration 26 Register (DDR3_CONFIG_26) ............................................................. 100
4.56 DDR3 Configuration 27 Register (DDR3_CONFIG_27) ............................................................. 101
4.57 DDR3 Configuration 28 Register (DDR3_CONFIG_28) ............................................................. 101
4.58 DDR3 Configuration 29 Register (DDR3_CONFIG_29) ............................................................. 102
4.59 DDR3 Configuration 30 Register (DDR3_CONFIG_30) ............................................................ 102
4.60 DDR3 Configuration 31 Register (DDR3_CONFIG_31) ............................................................. 103
4.61 DDR3 Configuration 32 Register (DDR3_CONFIG_32) ............................................................ 103
4.62 DDR3 Configuration 33 Register (DDR3_CONFIG_33) ............................................................. 104
4.63 DDR3 Configuration 34 Register (DDR3_CONFIG_34) ............................................................. 104
4.64 DDR3 Configuration 35 Register (DDR3_CONFIG_35) ............................................................. 105
4.65 DDR3 Configuration 36 Register (DDR3_CONFIG_36) ............................................................. 105
4.66 DDR3 Configuration 37 Register (DDR3_CONFIG_37) ............................................................. 106
4.67 DDR3 Configuration 38 Register (DDR3_CONFIG_38) ............................................................ 106
4.68 DDR3 Configuration 39 Register (DDR3_CONFIG_39) ............................................................ 107
4.69 DDR3 Configuration 40 Register (DDR3_CONFIG_40) ............................................................ 107
4.70 DDR3 Configuration 41 Register (DDR3_CONFIG_41) ............................................................. 108
4.71 DDR3 Configuration 42 Register (DDR3_CONFIG_42) ............................................................. 108
4.72 DDR3 Configuration 43 Register (DDR3_CONFIG_43) ............................................................. 109
4.73 DDR3 Configuration 44 Register (DDR3_CONFIG_44) ............................................................. 109
4.74 DDR3 Configuration 45 Register (DDR3_CONFIG_45) ............................................................. 110
4.75 DDR3 Configuration 46 Register (DDR3_CONFIG_46) ............................................................. 110
4.76 DDR3 Configuration 47 Register (DDR3_CONFIG_47) ............................................................. 111
4.77 DDR3 Configuration 48 Register (DDR3_CONFIG_48) ............................................................. 111
4.78 DDR3 Configuration 49 Register (DDR3_CONFIG_49) ............................................................. 112
4.79 DDR3 Configuration 50 Register (DDR3_CONFIG_50) ............................................................. 112
4.80 DDR3 Configuration 51 Register (DDR3_CONFIG_51) ............................................................. 113
4.81 DDR3 Configuration 52 Register (DDR3_CONFIG_52) ............................................................. 113
4.82 DDR3 Configuration 53 Register (DDR3_CONFIG_53) ............................................................. 114
4.83 DDR3 Configuration 54 Register (DDR3_CONFIG_54) ............................................................. 114
4.84 DDR3 Configuration 55 Register (DDR3_CONFIG_55) ............................................................. 115
4.85 DDR3 Configuration 56 Register (DDR3_CONFIG_56) ............................................................. 115
4.86 DDR3 Configuration 57 Register (DDR3_CONFIG_57) ............................................................. 116
4.87 DDR3 Configuration 58 Register (DDR3_CONFIG_58) ............................................................. 116
4.88 DDR3 Configuration 59 Register (DDR3_CONFIG_59) ............................................................. 117
4.89 DDR3 Configuration 60 Register (DDR3_CONFIG_60) ............................................................. 117
Revision History ........................................................................................................................ 119

4 Contents SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com

List of Figures
2-1. DDR3 Memory Control Signals ........................................................................................... 17
2-2. READ Command ........................................................................................................... 21
2-3. WRITE Command .......................................................................................................... 21
2-4. Logical Address-to-DDR3 SDRAM Address Map (EBANK=0) ....................................................... 26
2-5. DDR3 SDRAM Column, Row, and Bank Access (EBANK=0) ....................................................... 26
2-6. DDR3 Memory Controller FIFO Block Diagram ........................................................................ 27
3-1. Connecting Two 16 MB x 16 x 8 Banks (4Gb Total) Devices ........................................................ 45
3-2. Connecting One 8 MB x 16 x 8 Banks (1Gb Total) Device ........................................................... 46
3-3. Connecting Two 16 MB x 8 x 8 Banks (2Gb Total) Devices ......................................................... 47
4-1. Module ID and Revision Register (MIDR) ............................................................................... 55
4-2. DDR3 Memory Controller Status Register (STATUS) ................................................................. 56
4-3. SDRAM Configuration Register (SDCFG) .............................................................................. 57
4-4. SDRAM Refresh Control Register (SDRFC)............................................................................ 59
4-5. SDRAM Timing 1 (SDTIM1) Register ................................................................................... 60
4-6. SDRAM Timing 2 (SDTIM2) Register ................................................................................... 61
4-7. SDRAM Timing 3 (SDTIM3) Register ................................................................................... 62
4-8. Power Management Control Register (PMCTL) ....................................................................... 63
4-9. VBUSM Configuration Register (VBUSM_CONFIG) .................................................................. 65
4-10. Performance Counter 1 Register (PERF_CNT_1) ..................................................................... 66
4-11. Performance Counter 2 Register (PERF_CNT_2) ..................................................................... 67
4-12. Performance Counter Config Register (PERF_CNT_CFG) .......................................................... 68
4-13. Performance Counter Master Region Select Register (PERF_CNT_SEL) ......................................... 69
4-14. Performance Counter Time Register (PERF_CNT_TIM) ............................................................. 70
4-15. Interrupt Raw Status Register (IRQSTATUS_RAW_SYS) ........................................................... 71
4-16. Interrupt Status Register (IRQSTATUS_ SYS) ......................................................................... 72
4-17. Interrupt Enable Set Register (IRQSTATUS_ SET_SYS) ............................................................ 73
4-18. Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS) .......................................................... 74
4-19. SDRAM Output Impedance Calibration Configuration Register (ZQCFG).......................................... 75
4-20. Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN) .......................................... 77
4-21. Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL).......................................... 78
4-22. Read-Write Leveling Control Register (RDWR_LVL_CTRL) ......................................................... 79
4-23. DDR PHY Control 1 Register (DDR_PHY_CTRL_1) .................................................................. 80
4-24. Priority to Class-Of-Service Mapping Register (PRI_COS_MAP) ................................................... 81
4-25. Master ID to Class-Of-Service 1 Mapping Register (MSTID_COS_1_MAP) ....................................... 82
4-26. Master ID to Class-Of-Service 2 Mapping Register (MSTID_COS_2_MAP) ....................................... 83
4-27. ECC Control Register (ECCCTL) ........................................................................................ 84
4-28. ECC Address Range 1 Register (ECCADDR1) ........................................................................ 85
4-29. ECC Address Range 2Register (ECCADDR2) ......................................................................... 86
4-30. Read Write Execution Threshold Register (RWTHRESH) ............................................................ 87
4-31. DDR3 Configuration 0 Register (DDR3_CONFIG_0) ................................................................. 88
4-32. DDR3 Configuration 1 Register (DDR3_CONFIG_1) ................................................................. 89
4-33. DDR3 Configuration 2 Register (DDR3_CONFIG_2) ................................................................. 89
4-34. DDR3 Configuration 3 Register (DDR3_CONFIG_3) ................................................................. 90
4-35. DDR3 Configuration 4 Register (DDR3_CONFIG_4) ................................................................. 90
4-36. DDR3 Configuration 5 Register (DDR3_CONFIG_5) ................................................................. 91
4-37. DDR3 Configuration 6 Register (DDR3_CONFIG_6) ................................................................. 91
4-38. DDR3 Configuration 7 Register (DDR3_CONFIG_7) ................................................................. 92

SPRUGV8E – November 2010 – Revised January 2015 List of Figures 5

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 www.ti.com

4-39. DDR3 Configuration 8 Register (DDR3_CONFIG_8) ................................................................. 92

4-40. DDR3 Configuration 9 Register (DDR3_CONFIG_9) ................................................................. 93
4-41. DDR3 Configuration 10 Register (DDR3_CONFIG_10) .............................................................. 93
4-42. DDR3 Configuration 12 Register (DDR3_CONFIG_12) .............................................................. 94
4-43. DDR3 Configuration 14 Register (DDR3_CONFIG_14) .............................................................. 94
4-44. DDR3 Configuration 15 Register (DDR3_CONFIG_15) .............................................................. 95
4-45. DDR3 Configuration 16 Register (DDR3_CONFIG_16) .............................................................. 95
4-46. DDR3 Configuration 17 Register (DDR3_CONFIG_17) .............................................................. 96
4-47. DDR3 Configuration 18 Register (DDR3_CONFIG_18) .............................................................. 96
4-48. DDR3 Configuration 19 Register (DDR3_CONFIG_19) .............................................................. 97
4-49. DDR3 Configuration 20 Register (DDR3_CONFIG_20) .............................................................. 97
4-50. DDR3 Configuration 21 Register (DDR3_CONFIG_21) .............................................................. 98
4-51. DDR3 Configuration 22 Register (DDR3_CONFIG_22) .............................................................. 98
4-52. DDR3 Configuration 23 Register (DDR3_CONFIG_23) .............................................................. 99
4-53. DDR3 Configuration 24 Register (DDR3_CONFIG_24) .............................................................. 99
4-54. DDR3 Configuration 25 Register (DDR3_CONFIG_25) ............................................................. 100
4-55. DDR3 Configuration 26 Register (DDR3_CONFIG_26) ............................................................. 100
4-56. DDR3 Configuration 27 Register (DDR3_CONFIG_27) ............................................................. 101
4-57. DDR3 Configuration 28 Register (DDR3_CONFIG_28) ............................................................. 101
4-58. DDR3 Configuration 29 Register (DDR3_CONFIG_29) ............................................................. 102
4-59. DDR3 Configuration 30 Register (DDR3_CONFIG_30) ............................................................. 102
4-60. DDR3 Configuration 31 Register (DDR3_CONFIG_31) ............................................................. 103
4-61. DDR3 Configuration 32 Register (DDR3_CONFIG_32) ............................................................. 103
4-62. DDR3 Configuration 33 Register (DDR3_CONFIG_33) ............................................................. 104
4-63. DDR3 Configuration 34 Register (DDR3_CONFIG_34) ............................................................. 104
4-64. DDR3 Configuration 35 Register (DDR3_CONFIG_35) ............................................................. 105
4-65. DDR3 Configuration 36 Register (DDR3_CONFIG_36) ............................................................. 105
4-66. DDR3 Configuration 37 Register (DDR3_CONFIG_37) ............................................................. 106
4-67. DDR3 Configuration 38 Register (DDR3_CONFIG_38) ............................................................. 106
4-68. DDR3 Configuration 39 Register (DDR3_CONFIG_39) ............................................................. 107
4-69. DDR3 Configuration 40 Register (DDR3_CONFIG_40) ............................................................. 107
4-70. DDR3 Configuration 41 Register (DDR3_CONFIG_41) ............................................................. 108
4-71. DDR3 Configuration 42 Register (DDR3_CONFIG_42) ............................................................. 108
4-72. DDR3 Configuration 43 Register (DDR3_CONFIG_43) ............................................................. 109
4-73. DDR3 Configuration 44 Register (DDR3_CONFIG_44) ............................................................. 109
4-74. DDR3 Configuration 45 Register (DDR3_CONFIG_45) ............................................................. 110
4-75. DDR3 Configuration 46 Register (DDR3_CONFIG_46) ............................................................. 110
4-76. DDR3 Configuration 47 Register (DDR3_CONFIG_47) ............................................................. 111
4-77. DDR3 Configuration 48 Register (DDR3_CONFIG_48) ............................................................. 111
4-78. DDR3 Configuration 49 Register (DDR3_CONFIG_49) ............................................................. 112
4-79. DDR3 Configuration 50 Register (DDR3_CONFIG_50) ............................................................. 112
4-80. DDR3 Configuration 51 Register (DDR3_CONFIG_51) ............................................................. 113
4-81. DDR3 Configuration 52 Register (DDR3_CONFIG_52) ............................................................. 113
4-82. DDR3 Configuration 53 Register (DDR3_CONFIG_53) ............................................................. 114
4-83. DDR3 Configuration 54 Register (DDR3_CONFIG_54) ............................................................. 114
4-84. DDR3 Configuration 55 Register (DDR3_CONFIG_55) ............................................................. 115
4-85. DDR3 Configuration 56 Register (DDR3_CONFIG_56) ............................................................. 115
4-86. DDR3 Configuration 57 Register (DDR3_CONFIG_57) ............................................................. 116
4-87. DDR3 Configuration 58 Register (DDR3_CONFIG_58) ............................................................. 116

6 List of Figures SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com

4-88. DDR3 Configuration 59 Register (DDR3_CONFIG_59) ............................................................. 117

4-89. DDR3 Configuration 60 Register (DDR3_CONFIG_60) ............................................................. 117

SPRUGV8E – November 2010 – Revised January 2015 List of Figures 7

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 www.ti.com

List of Tables
2-1. DDR3 Memory Controller Signal Descriptions ......................................................................... 17
2-2. DDR3 SDRAM Commands .............................................................................................. 18
2-3. Truth Table for DDR3 SDRAM Commands ............................................................................. 19
2-4. Bank Configuration Register Fields for Address Mapping ............................................................ 22
2-5. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 0 ................................................ 23
2-6. Address Mapping Example (IBANK_POS=0, IBANK=3, PAGESIZE=3, EBANK=1, 64-bit SDRAM) ........... 23
2-7. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 1 ................................................ 23
2-8. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 2 ................................................ 24
2-9. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 3 ................................................ 25
2-10. DDR3 Memory Controller FIFO Description ............................................................................ 27
2-11. Device and DDR3 Memory Controller Reset Relationship ........................................................... 31
2-12. Turnaround Time ........................................................................................................... 32
2-13. DDR3 SDRAM Extended Mode Register 2 Configuration ........................................................... 33
2-14. DDR3 SDRAM Extended Mode Register 1 Configuration ............................................................ 33
2-15. DDR3 SDRAM Mode Register 0 Configuration ........................................................................ 33
2-16. DATAx register to byte lane mapping ................................................................................... 36
2-17. Performance Counter Filter Configuration ............................................................................. 41
3-1. SDCFG Configuration ..................................................................................................... 48
3-2. DDR3 Memory Refresh Specification.................................................................................... 48
3-3. SDRFC Configuration ...................................................................................................... 49
3-4. See the register section for the SDTIM* register where the field exists ............................................ 49
3-5. See the register section for the SDTIM* register where the field exists ............................................ 50
3-6. See the register section for the SDTIM* register where the field exists ............................................ 50
4-1. DDR3 Memory Controller Registers (See datasheet memory map for base address) ........................... 52
4-2. DDR3 PHY Leveling Registers (See device datasheet for base address) ......................................... 53
4-3. Module ID and Revision Register (MIDR) Field Descriptions ........................................................ 55
4-4. DDR3 Memory Controller Status Register (STATUS) Field Descriptions .......................................... 56
4-5. SDRAM Configuration Register (SDCFG) Field Descriptions ........................................................ 57
4-6. SDRAM Refresh Control (SDRFC) Register Field Descriptions ..................................................... 59
4-7. SDRAM Timing 1 (SDTIM1) Register Field Descriptions ............................................................ 60
4-8. SDRAM Timing 2 (SDTIM2) Register Field Descriptions ............................................................ 61
4-9. SDRAM Timing 3 (SDTIM3) Register Field Descriptions ............................................................ 62
4-10. Power Management Control Register (PMCTL) Field Descriptions ................................................. 63
4-11. VBUSM Configuration Register (VBUSM_CONFIG) Field Descriptions ............................................ 65
4-12. Performance Counter 1 Register (PERF_CNT_1) Field Descriptions ............................................... 66
4-13. Performance Counter 2 Register (PERF_CNT_2) Field Descriptions ............................................... 67
4-14. Performance Counter Config Register (PERF_CNT_CFG) Field Descriptions .................................... 68
4-15. Performance Counter Master Region Select Register (PERF_CNT_SEL) Field Descriptions ................... 69
4-16. Performance Counter Time Register (PERF_CNT_TIM) Field Descriptions ....................................... 70
4-17. Interrupt Raw Status Register (IRQSTATUS_RAW_SYS) Field Descriptions ..................................... 71
4-18. Interrupt Status Register (IRQSTATUS_SYS) Field Descriptions ................................................... 72
4-19. Interrupt Enable Set Register (IRQSTATUS_ SET_SYS) Field Descriptions ...................................... 73
4-20. Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS) Field Descriptions ................................... 74
4-21. SDRAM Output Impedance Calibration Configuration Register (ZQCFG) Field Descriptions .................. 75
4-22. Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN) Field Descriptions .................... 77
4-23. Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL) Field Descriptions ................... 78
4-24. Read-Write Leveling Control Register (RDWR_LVL_CTRL) Field Descriptions ................................... 79

8 List of Tables SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com

4-25. DDR PHY Control 1 Register (DDR_PHY_CTRL_1) Field Descriptions............................................ 80

4-26. Priority to Class-Of-Service Mapping Register (PRICOSMAP) Field Descriptions ................................ 81
4-27. Master ID to Class-Of-Service Mapping 1 Register (MSTID_COS_1_MAP) Field Descriptions ................ 82
4-28. Master ID to Class-Of-Service Mapping 2 Register (MSTID_COS_2_MAP) Field Descriptions ................ 83
4-29. ECC Control Register (ECCCTL) Field Descriptions ................................................................. 84
4-30. ECC Address Range 1 Register Field Descriptions ................................................................... 85
4-31. ECC Address Range 2 Register Field Descriptions ................................................................... 86
4-32. Read Write Execution Threshold Register (RWTHRESH) Field Descriptions ..................................... 87
4-33. DDR3_CONFIG_0 Register (0x02620404) Field Descriptions ....................................................... 88
4-34. DDR3_CONFIG_1 Register (0x02620408) Field Descriptions ....................................................... 89
4-35. DDR3_CONFIG_2 Register (0x0262040C) Field Descriptions ...................................................... 89
4-36. DDR3_CONFIG_3 Register (0x02620410) Field Descriptions ....................................................... 90
4-37. DDR3_CONFIG_4 Register (0x02620414) Field Descriptions ....................................................... 90
4-38. DDR3_CONFIG_5 Register (0x02620418) Field Descriptions ....................................................... 91
4-39. DDR3_CONFIG_6 Register (0x0262041C) Field Descriptions ...................................................... 91
4-40. DDR3_CONFIG_7 Register (0x02620420) Field Descriptions ....................................................... 92
4-41. DDR3_CONFIG_8 Register (0x02620424) Field Descriptions ....................................................... 92
4-42. DDR3_CONFIG_9 Register (0x02620428) Field Descriptions ....................................................... 93
4-43. DDR3_CONFIG_10 Register (0x0262042C) Field Descriptions ..................................................... 93
4-44. DDR3_CONFIG_12 Register (0x02620434) Field Descriptions ..................................................... 94
4-45. DDR3_CONFIG_14 Register (0x0262043C) Field Descriptions ..................................................... 94
4-46. DDR3_CONFIG_15 Register (0x02620440) Field Descriptions ..................................................... 95
4-47. DDR3_CONFIG_16 Register (0x02620444) Field Descriptions ..................................................... 95
4-48. DDR3_CONFIG_17 Register (0x02620448) Field Descriptions ..................................................... 96
4-49. DDR3_CONFIG_18 Register (0x0262044C) Field Descriptions ..................................................... 96
4-50. DDR3_CONFIG_19 Register (0x02620450) Field Descriptions ..................................................... 97
4-51. DDR3_CONFIG_20 Register (0x02620454) Field Descriptions ..................................................... 97
4-52. DDR3_CONFIG_21 Register (0x02620458) Field Descriptions ..................................................... 98
4-53. DDR3_CONFIG_22 Register (0x0262045C) Field Descriptions ..................................................... 98
4-54. DDR3_CONFIG_23 Register (0x02620460) Field Descriptions ..................................................... 99
4-55. DDR3_CONFIG_24 Register (0x02620464) Field Descriptions ..................................................... 99
4-56. DDR3_CONFIG_25 Register (0x02620468) Field Descriptions .................................................... 100
4-57. DDR3_CONFIG_26 Register (0x0262046C) Field Descriptions ................................................... 100
4-58. DDR3_CONFIG_27 Register (0x02620470) Field Descriptions .................................................... 101
4-59. DDR3_CONFIG_28 Register (0x02620474) Field Descriptions .................................................... 101
4-60. DDR3_CONFIG_29 Register (0x02620478) Field Descriptions .................................................... 102
4-61. DDR3_CONFIG_30 Register (0x0262047C) Field Descriptions ................................................... 102
4-62. DDR3_CONFIG_31 Register (0x02620480) Field Descriptions .................................................... 103
4-63. DDR3_CONFIG_32 Register (0x02620484) Field Descriptions .................................................... 103
4-64. DDR3_CONFIG_33 Register (0x02620488) Field Descriptions .................................................... 104
4-65. DDR3_CONFIG_34 Register (0x0262048C) Field Descriptions ................................................... 104
4-66. DDR3_CONFIG_35 Register (0x02620490) Field Descriptions .................................................... 105
4-67. DDR3_CONFIG_36 Register (0x02620494) Field Descriptions .................................................... 105
4-68. DDR3_CONFIG_37 Register (0x02620498) Field Descriptions .................................................... 106
4-69. DDR3_CONFIG_38 Register (0x0262049C) Field Descriptions ................................................... 106
4-70. DDR3_CONFIG_39 Register (0x026204A0) Field Descriptions.................................................... 107
4-71. DDR3_CONFIG_40 Register (0x026204A4) Field Descriptions.................................................... 107
4-72. DDR3_CONFIG_41 Register (0x026204A8) Field Descriptions.................................................... 108
4-73. DDR3_CONFIG_42 Register (0x026204AC) Field Descriptions ................................................... 108

SPRUGV8E – November 2010 – Revised January 2015 List of Tables 9

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 www.ti.com

4-74. DDR3_CONFIG_43 Register (0x026204B0) Field Descriptions.................................................... 109

4-75. DDR3_CONFIG_44 Register (0x026204B4) Field Descriptions.................................................... 109
4-76. DDR3_CONFIG_45 Register (0x026204B8) Field Descriptions.................................................... 110
4-77. DDR3_CONFIG_46 Register (0x026204BC) Field Descriptions ................................................... 110
4-78. DDR3_CONFIG_47 Register (0x026204C0) Field Descriptions ................................................... 111
4-79. DDR3_CONFIG_48 Register (0x026204C4) Field Descriptions ................................................... 111
4-80. DDR3_CONFIG_49 Register (0x026204C8) Field Descriptions ................................................... 112
4-81. DDR3_CONFIG_50 Register (0x026204CC) Field Descriptions ................................................... 112
4-82. DDR3_CONFIG_51 Register (0x026204D0) Field Descriptions ................................................... 113
4-83. DDR3_CONFIG_52 Register (0x026204D4) Field Descriptions ................................................... 113
4-84. DDR3_CONFIG_53 Register (0x026204D8) Field Descriptions ................................................... 114
4-85. DDR3_CONFIG_54 Register (0x026204DC) Field Descriptions ................................................... 114
4-86. DDR3_CONFIG_55 Register (0x026204E0) Field Descriptions.................................................... 115
4-87. DDR3_CONFIG_56 Register (0x026204E4) Field Descriptions.................................................... 115
4-88. DDR3_CONFIG_57 Register (0x026204E8) Field Descriptions.................................................... 116
4-89. DDR3_CONFIG_58 Register (0x026204EC) Field Descriptions ................................................... 116
4-90. DDR3_CONFIG_59 Register (0x026204F0) Field Descriptions .................................................... 117
4-91. DDR3_CONFIG_60 Register (0x026204F4) Field Descriptions .................................................... 117

10 List of Tables SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 Read This First
SPRUGV8E – November 2010 – Revised January 2015

Preface

About This Manual

The DDR3 memory controller is used to interface with JESD79-3C standard compliant SDRAM devices.
Memory types such as DDR1 SDRAM, DDR2 SDRAM, SDR SDRAM, SBSRAM, and asynchronous
memories are not supported. The DDR3 memory controller SDRAM can be used for program and data
storage.

Notational Conventions
This document uses the following conventions:
• Commands and keywords are in boldface font.
• Arguments for which you supply values are in italic font.
• Terminal sessions and information the system displays are in screen font.
• Information you must enter is in boldface screen font.
• Elements in square brackets ([ ]) are optional.
Notes use the following conventions:

NOTE: Means reader take note. Notes contain helpful suggestions or references to material not
covered in the publication.

The information in a caution or a warning is provided for your protection. Please read each caution and
warning carefully.

CAUTION
Indicates the possibility of service interruption if precautions are not taken.

WARNING
Indicates the possibility of damage to equipment if precautions are
not taken.

Related Documentation from Texas Instruments

C66x CorePac User Guide SPRUGW0

C66x CPU and Instruction Set Reference Guide SPRUGH7
Enhanced Direct Memory Access 3 (EDMA3) for KeyStone Devices User Guide SPRUGS5
External Memory Interface (EMIF16) for KeyStone Devices User Guide SPRUGZ3
Interrupt Controller (INTC) for KeyStone Devices User Guide SPRUGW4

All trademarks are the property of their respective owners.

SPRUGV8E – November 2010 – Revised January 2015 Preface 11

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
About This Manual www.ti.com

12 Preface SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 Chapter 1
SPRUGV8E – November 2010 – Revised January 2015

Introduction

This document describes the operation of the DDR3 module in the KeyStone II devices. (Refer to the
device-specific data manual for exact device applicability.) The DDR3 module is accessible across all the
cores and all system masters that are not cores.

Topic ........................................................................................................................... Page

1.1 Purpose of the Peripheral.................................................................................... 14

1.2 Features ............................................................................................................ 14
1.3 Industry Standard(s) Compliance Statement.......................................................... 14

SPRUGV8E – November 2010 – Revised January 2015 Introduction 13

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Purpose of the Peripheral www.ti.com

1.1 Purpose of the Peripheral

The DDR3 memory controller is used to interface with JESD79-3C standard compliant SDRAM devices.
Memory types such as DDR1 SDRAM, DDR2 SDRAM, SDR SDRAM, SBSRAM, and asynchronous
memories are not supported. The DDR3 memory controller SDRAM can be used for program and data
storage. The KeyStone device has one instance.

1.2 Features
The DDR3 controller supports the following features:
• Supports JEDEC standard JESD79-3C – DDR3 compliant devices
• 33-bit address for 8 GB of address space
• 16/32/64-bit data bus width support
• CAS latencies: 5, 6, 7, 8, 9, 10, and 11
• 1, 2, 4, and 8 internal banks
• Burst Length: 8
• Burst Type: sequential
• 8GB address space available over one or two chip selects
• Page sizes: 256, 512, 1024, and 2048-word
• SDRAM auto initialization from reset or configuration change
• Self-refresh mode
• Prioritized refresh scheduling
• Programmable SDRAM refresh rate and backlog counter
• Programmable SDRAM timing parameters
• Big and little endian modes
• ECC on SDRAM data bus
• 8-bit ECC per 64-bit data quanta without additional cycle latency
• Two latency classes supported
• UDIMM Address mirroring is not supported

1.3 Industry Standard(s) Compliance Statement

The DDR3 controller is compliant with the JESD79-3C DDR3 SDRAM standard.

14 Introduction SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Industry Standard(s) Compliance Statement

SPRUGV8E – November 2010 – Revised January 2015 Introduction 15

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 Chapter 2
SPRUGV8E – November 2010 – Revised January 2015

Peripheral Architecture

The DDR3 controller interfaces with most standard DDR3 SDRAM devices. It supports self-refresh mode
and prioritized refresh. In addition, it provides flexibility through programmable parameters such as the
refresh rate, CAS latency, and many SDRAM timing parameters. The following sections describe the
architecture of the DDR3 controller as well as how to interface and configure it to perform read and write
operations to DDR3 SDRAM devices. Examples for interfacing the DDR3 controller to a common DDR3
SDRAM device are shown in Section 3.1.

Topic ........................................................................................................................... Page

2.1 Clock Interface ................................................................................................... 17

2.2 SDRAM Memory Map .......................................................................................... 17
2.3 Signal Descriptions ............................................................................................ 17
2.4 Protocol Descriptions ......................................................................................... 18
2.5 Address Mapping ............................................................................................... 22
2.6 DDR3 Memory Controller Interface ....................................................................... 27
2.7 Refresh Scheduling ............................................................................................ 30
2.8 Self-Refresh Mode .............................................................................................. 30
2.9 Reset Considerations ......................................................................................... 31
2.10 Turnaround Time................................................................................................ 32
2.11 DDR3 SDRAM Memory Initialization...................................................................... 32
2.12 Dual Rank Support ............................................................................................. 34
2.13 Leveling ............................................................................................................ 34
2.14 Interrupt Support................................................................................................ 39
2.15 EDMA Event Support .......................................................................................... 39
2.16 Emulation Considerations ................................................................................... 39
2.17 ECC .................................................................................................................. 39
2.18 Power Management ............................................................................................ 40
2.19 Performance Monitoring...................................................................................... 40

16 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Clock Interface

2.1 Clock Interface

There are two clocking schemes in the DDR3 controller - the clocking scheme used to drive the DDR3
controller and the clocking scheme used to drive the DDR3 I/O interface. The DDR3 controller is clocked
by the DSP/2 clock domain. The I/O interface is driven by the DDR3 memory clock (half the data rate).

2.2 SDRAM Memory Map

For information describing the DDR3 memory map, see the device-specific data manual.

2.3 Signal Descriptions

The DDR3 memory controller signals are shown in Figure 2-1 and described in Figure 2-1.
• The maximum data bus is 64-bits wide.
• The address bus is 33-bits wide.
• Two differential output clocks driven by internal clock sources.
• Command signals: Row and column address strobe, write enable strobe, data strobe, and data mask.
• Two chip selects and two clock enable signals.

Figure 2-1. DDR3 Memory Control Signals

DDRCLKOUTP [1:0]

DDRCLKOUTN [1:0]

DDRCKE [1:0]

DDRCE[1:0]

DDRWE

DDRRAS

DDRCAS

DDR3 DDRDQM [8:0]

MEMORY
CONTROLLER DDRDQSP [8:0]

DDRDQSN [8:0]

DDRBA [2:0]

DDRA [15:0]

DDRD [63:0]
DDRCB [7:0]
DDRODT [1:0]

DDRRESET

VREFSSTTL

Table 2-1. DDR3 Memory Controller Signal Descriptions

Pin Description
DDRD [63:0] Bidirectional data bus. Input for data reads and output for data writes.
DDRCB [7:0] Bidirectional data bus (check bits) for ECC byte lane. Input for data reads and output for data writes.
DDRA [15:0] External address output.
DDRCE0 Active-low chip enable for memory space CE0. DDRCE0z is used to enable the DDR3 SDRAM
memory device during external memory accesses.
DDRCE1 Active-low chip enable for memory space CE1. DDRCE1z is used to enable the DDR3 SDRAM
memory device during external memory accesses.
DDRDQM [8:0] Active-high output data mask.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 17

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Protocol Descriptions www.ti.com

Table 2-1. DDR3 Memory Controller Signal Descriptions (continued)

Pin Description
DDR3CLKOUTP [1:0]/
Differential clock outputs.
DDR3CLKOUTN [1:0]
DDRCKE [1:0] Clock enable (used for self-refresh mode).
DDRCAS Active-low column address strobe.
DDRRAS Active-low row address strobe.
DDRWE Active-low write enable.
DDRDQSP [8:0]/
Differential data strobe bidirectional signals.
DDRDQSN [8:0]
DDRODT [1:0] On-die termination signal(s) to external DDR3 SDRAM
DDRBA [2:0] Bank-address control outputs
VREFSSTTL DDR3 Memory Controller reference voltage. This voltage must be supplied externally. For more
details, see the device-specific data manual.
DDRSLRATE [1:0] See the section on Slew Rate Control in the Hardware Design Guide for Keystone Devices
(SPRABI2) for details.

2.4 Protocol Descriptions

The DDR3 memory controller supports the DDR3 SDRAM commands listed in Table 2-2.

Table 2-2. DDR3 SDRAM Commands

Command Function
ACT Activates the selected bank and row.
PREA Precharge all command. Deactivates (precharges) all banks.
PRE Precharge single command. Deactivates (precharges) a single bank.
DES Device Deselect.
EMRS Extended Mode Register set. Allows altering the contents of the mode register.
MRS Mode register set. Allows altering the contents of the mode register.
NOP No operation.
PDE Power down entry
PDX Power down exit
RD Inputs the starting column address and begins the read operation.
REF Autorefresh cycle
SRE Self-refresh entry
SRX Self-refresh exit
WR Inputs the starting column address and begins the write operation.
ZQCS ZQ Calibration short operation
ZQCL ZQ Calibration long operation

18 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Protocol Descriptions

Table 2-3 shows the signal truth table for the DDR3 SDRAM commands.

Table 2-3. Truth Table for DDR3 SDRAM Commands (1)

DDR3
SDRAM A [9:0],
Signals CKE CS# RAS# CAS# WE# BA [2:0] A [15:13] A12 A10 A11
DDRCKE
DDR3 Memory
controller Previous Current DDRBA DDRA DDRA DDRA DDRA
signals Cycle Cycle DCE DDRRAS DDRCAS DDRWE [2:0] [15:13] [12] [10] [9:0],[11]
ACT H H L L H H BA Row Address (RA)
PREA H H L L H L V V V H V
PRE H H L L H L BA V V L V
MRS H H L L L L BA OP Code
EMRS (2) H H L L L L BA OP Code
RD (BL8) H H L H L H BA RFU V L CA
WR (BL8) H H L H L L BA RFU V L CA
REF H H L L L H V V V V V
SRE (3) H L L L L H V V V V V
(3) (4)
SRX H X X X X X X X X
L H
L H H H V X V V V
NOP H H L H H H V V V V V
DES (5) H H H X X X X X X X X
PDE (6) L H H H V V V V V
H L
X X X X X X X X X
PDX (6) L H H H V V V V V
L H
X X X X X X X X X
ZQCL H H L H H L X X X H X
ZQCS H H L H H L X X X L X
(1)
LEGEND: H = Logic High, L = Logic Low, X = Don’t Care, RA = Row Address, CA = Column Address, RFU = Reserved for
future use, V = Valid
(2)
For extended mode register set (EMRS) command, bank address (BA) pins select an extended mode register (EMR).
(3)
ODT function is not available during self-refresh.
(4)
Self-refresh exit (SRE) is asynchronous.
(5)
The Deselect (DES) command performs the same function as No Operation (NOP).
(6)
The Power down mode does not perform any self-refresh operation.

2.4.1 Mode Register Set (MRS or EMRS)

DDR3 SDRAM contains mode and extended mode registers that configure the DDR3 memory for
operation. These registers control burst type, burst length, CAS latency, DLL enable/disable, etc.
The DDR3 memory controller programs the mode and extended mode registers of the DDR3 memory by
issuing MRS and EMRS commands. MRS and EMRS commands can be issued during DDR3 initialization
as well as during normal operation as long as the external SDRAM is in idle state. When the MRS or
EMRS command is executed, the value on DDRBA [1:0] selects the mode register to be written and the
data on DDRA [12:0] is loaded into the register. DDRA [15:13] and DDRBA [2] are reserved and are
programmed to 0 during MRS (or EMRS).
Each mode register allows programming of different sets of DDR3 SDRAM parameters. The DDR3
memory controller programs the mode registers in compliance with the JEDEC JESD79-3C spec. For
more information about mode registers and how they are programmed, see the JEDEC spec.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 19

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Protocol Descriptions www.ti.com

2.4.2 Refresh Mode

The DDR3 memory controller issues refresh commands (REF) to the DDR3 SDRAM device. REF is
automatically preceded by a Precharge-all (PREA) command, ensuring the deactivation of all CE spaces
and banks selected.
Following the PREA command, the DDR3 memory controller begins performing refreshes at a rate defined
by the refresh rate (REFRESH_RATE) field in the SDRAM refresh control register (SDRFC). In general, a
refresh command needs to be issued to the DDR3 SDRAM regularly every tREFI interval. To allow for
efficient operation, refresh commands can be postponed a maximum of 8 times. Also, at any given time a
maximum of 16 refresh commands can issued within a 2 xtREFI interval. For more information on refresh
command timing, see the JEDEC spec.

2.4.3 Activation
The ACTIVE command is used to open (or activate) a row in a specific bank for a subsequent access.
DDRBA [2:0] select the bank, and the address provided on DDRA[15:0] selects the row. This row remains
active (or open) for accesses until a precharge command is issued to that bank. A PRECHARGE
command must be issued before opening a different row in the same bank.
When the DDR3 memory controller issues an ACT command, a delay of tRCD is incurred before a read or
write command is issued. Reads or writes to the currently active row and bank of memory can achieve
much higher throughput than reads or writes to random areas because every time a new row is accessed,
the ACT command must be issued and a delay of tRCD incurred.

2.4.4 Deactivation
The precharge command is used to deactivate the open row in a particular bank (PRE) or the open row in
all banks (PREA). The bank(s) will be available for a subsequent row activation a specified time (tRP) after
the precharge command is issued, except in the case of concurrent auto precharge, where a read or write
command to a different bank is allowed as along as it does not interrupt the data transfer in the current
bank and does not violate any other timing parameters. A PRE command is allowed if there is no open
row in that bank (idle state) or if the previously open row is already in the process of precharging. During a
PREA command, DDRA [10] is driven high to ensure deactivation of all banks.

2.4.5 READ Command

Figure 2-2 shows the DDR3 memory controller performing a read burst from DDR3 SDRAM. The READ
command initiates a burst read operation to an active row. The column address is driven on DDRA [15:0],
and the bank address is driven on DDRBA [2:0].
The DDR3 memory controller uses a burst length of 8, and has a programmable CAS latency of 5, 6, 7, 8,
9, 10, or 11. The CAS latency is five cycles in Figure 2-2. Read latency can be programmed in the DDR
PHY Control 1 register and can take integer values from CL+1 to CL+7. In this figure it has been
programmed to CL + 1. Because the default burst size is 8, the DDR3 memory controller returns 8 words
of data for every read command. Word size is nothing but the DDR3 interface bus width.
If additional accesses are not pending to the DDR3 memory controller, the read burst completes and the
unneeded data is disregarded. If additional accesses are pending, based on the arbitration result, the
DDR3 memory controller can terminate the read burst and start a new read burst.

20 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Protocol Descriptions

Figure 2-2. READ Command

DDRCLKOUTP
DDRCLKOUTN

Command RD NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP

Address Bank,
col
tR P R E tRP S T

DQSP,
DQSN
DIN DIN DIN DIN DIN DIN DIN DIN
DDRDIN n n+1 n+2 n+3 n+4 n+5 n+6 n+7
RL = CL + 1

NOP commands are shown for ease of illustration ; other commands may be valid at these times
.

2.4.6 Write (WR) Command

Prior to a WRT command, the desired bank and row are activated by the ACT command. Following the
WRT command, a write latency is incurred. Write latency is equal to CAS latency minus 1. All writes have
a burst length of 8.
Figure 2-3 shows the timing for a write on the DDR3 memory controller. If the transfer request is for less
than 8 words, depending on the scheduling result and the pending commands, the DDR3 memory
controller can:
• Mask out the additional data using DDRDQM outputs
• Terminate the write burst and start a new write burst

Figure 2-3. WRITE Command

DDRCLKOUTP
DDRCLKOUTN

Command WR NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP

Address Bank,
col

tW P R E tWP S T
DQSP,
DQSN
WL = CL - 1 DOUT DOUT DOUT DOUT DOUT DOUT DOUT DOUT
DDRDOUT n n+1 n+2 n+3 n+4 n+5 n+6 n+7

NOP commands are shown for ease of illustration ; other commands may be valid at these times
.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 21

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Address Mapping www.ti.com

2.5 Address Mapping

The DDR3 memory controller views external DDR3 SDRAM as one continuous block of memory across
the two chip-selects. If smaller devices are used, the memory is seen to roll over. The DDR3 memory
controller receives DDR3 memory access requests along with a 33-bit logical address from the rest of the
system. The controller uses the logical address to generate a row/page, column, bank address, and chip
selects for the DDR3 SDRAM. The number of bank and column address bits used is determined by the
IBANK and PAGESIZE fields. The chip selection pins used are determined by the EBANK field
(Table 2-4).

Table 2-4. Bank Configuration Register Fields for Address Mapping

Bit Field Bit Value Bit Description
IBANK Defines the number of internal banks on external DDR3 memory
0 1 bank
1h 2 banks
2h 4 banks
3h 8 banks
PAGESIZE Defines the page size of each page of the external DDR3 memory
0 256 words (requires 8 column address bits)
1h 512 words (requires 9 column address bits)
2h 1024 words (requires 10 column address bits)
3h 2048 words (requires 11 column address bits)
EBANK External chip select setup. Defines whether SDRAM accesses use 1 or 2 chip select lines
0 Use only chip enable 0 for all SDRAM accesses
1 Use chip enables 0 and 1 for SDRAM accesses

NOTE: IBANK should always be programmed to 3h since DDR3 memory devices offer only 8-bank
support unlike DDR2 with the option of 4-bank or 8-bank memory devices.

The IBANK_POS bit field in the SDRAM Config Register (SDCFG) determines how many banks the DDR3
controller can interleave amongst. For IBANK POS = 0, as source address increments across SDRAM
page boundaries, the DDR3 controller moves to the same page in the next bank on current device (chip-
select).
After the page has been accessed in all banks of the current device, the same page is accessed in all
banks in the next device. This is followed by accessing the next page in the first device and the process
continues. To the DDR3 SDRAM, this process looks as shown on Figure 2-5. Thus IBANK_POS = 0
serves to maximize number of open banks within overall SDRAM space. The ROWSIZE parameter is not
used by the DDR3 controller if IBANK_POS = 0. See Figure 2-5.
Thus 16 banks (eight internal banks across two chip selects) can be kept open at a time, interleaving
among all of them.

22 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Address Mapping

Table 2-5. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 0

Logical Address [32:N]
Row Address Chip Select Bank Address[2:0] Column Address
ROW SIZE nrb EBANK ncs IBANK nbb PAGE SIZE ncb
Don’t care 16 bits 0 0 bits 0 0 bits 0 8 bits
1 1 bit 1 1 bit 1 9 bits
2 2 bits 2 10 bits
3 3 bits 3 11 bits
Logical address mapping for row Logical address mapping for chip Logical address mapping for Logical address mapping for
address select bank address[1:0] column address
MSB LSB MSB LSB MSB LSB MSB LSB
M3+nrb-1 M3+1 M3=M2+ M2+1 M2=M1+ M1+1 M1=N+ N
ncs-1 nbb-1 ncb-1

NOTE: N=1 for 16-bit SDRAM, N=2 for 32-bit SDRAM and N=3 for 64-bit SDRAM. ROWSIZE is not
used for IBANK_POS =0. nrb = Number of row bits. ncs = Number of chip select bits. nbb =
Number of bank select bits determined by bank address [2:0].

For example, if IBANK = 3, PAGESIZE = 3 and EBANK = 1, the address mapping for a 64-bit SDRAMs
would be as shown below in Table 2-6. For 64-bit, N = 3.

Table 2-6. Address Mapping Example

(IBANK_POS=0, IBANK=3, PAGESIZE=3, EBANK=1, 64-bit SDRAM)
SDCFG bit Logical Address
IBANK EBANK PAGESIZE 33:18 17 16:14 13:3
3 1 3 Don’t care ncs=1 nbb=3 ncb=11

For IBANK_POS = 1, interleaving is the same as IBANK_POS = 0 but limited to 4 banks per device (per
chip select). Thus 16 banks (8 internal banks across 2 chip selects) can be kept open at a time, but
interleaving among only 8 of them. The address mapping is shown in Table 2-7.

Table 2-7. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 1

Logical Address [32:N]
Bank Address [2] Row Address Chip Select Bank Address [1:0] Column Address
PAGE
IBANK nbb2 ROW SIZE nrb EBANK ncs IBANK nbb10 SIZE ncb
0 0 bits 0 9 bits 0 0 bits 0 0 bits 0 8 bits
1 0 bits 1 10 bits 1 1 bit 1 1 bit 1 9 bits
2 0 bits 2 11 bits 2 2 bits 2 10 bits
3 1 bit 3 12 bits 3 2 bits 3 11 bits
4 13 bits
5 14 bits
6 15 bits
7 16 bits
Logical address Logical address Logical address Logical address Logical address
mapping for mapping for row address mapping for chip select mapping for bank mapping for column
bank_address[2] address[1:0] address
MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB
M4+nbb2-1 M4+1 M4=M3+ M3+1 M3=M2+ M2+1 M2=M1+ M1+1 M1=N+ N
nrb-1 ncs-1 nbb10-1 ncb-1

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 23

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Address Mapping www.ti.com

NOTE: N=1 for 16-bit SDRAM; N=2 for 32-bit SDRAM; N=3 for 64-bit SDRAM. ncb = Number of
column address bits. nrb = Number of row bits. ncs = Number of chip select bits. nbb10 =
Number of bank select bits determined by bank address [1:0]. nbb2 = Number of bank select
bits determined by bank address[2].

For IBANK_POS = 2, interleaving is the same as IBANK_POS = 0 but limited to 2 banks per device (per
chip select). Thus 16 banks (8 internal banks across 2 chip selects) can be kept open at a time, but
interleaving among only 4 of them. The address mapping is shown in Table 2-8. An address mapping
table for the desired configuration can be generated on the lines of Table 2-6.

Table 2-8. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 2

Logical Address [32:N]
Bank Address [2:1] Row Address Chip Select Bank Address [0] Column Address
PAGE
IBANK nbb21 ROW SIZE nrb EBANK ncs IBANK nbb0 SIZE ncb
0 0 bits 0 9 bits 0 0 bits 0 0 bits 0 8 bits
1 0 bits 1 10 bits 1 1 bit 1 1 bit 1 9 bits
2 1 bit 2 11 bits 2 1 bit 2 10 bits
3 2 bits 3 12 bits 3 1 bit 3 11 bits
4 13 bits
5 14 bits
6 15 bits
7 16 bits
Logical address Logical address Logical address Logical address Logical address
mapping for mapping for row address mapping for chip select mapping for bank mapping for column
bank_address[2:1] address[0] address
MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB
M4+ M4+1 M4=M3+ M3+1 M3=M2+ M2+1 M2=M1+ M1+1 M1=N+ N
nbb21-1 nrb-1 ncs-1 nbb0-1 ncb-1

NOTE: N=1 for 16-bit SDRAM; N=2 for 32-bit SDRAM; N=3 for 64-bit SDRAM. ncb = Number of
column address bits. nrb = Number of row bits. ncs = Number of chip select bits. nbb0 =
Number of bank select bits determined by bank address [0]. nbb21 = Number of bank select
bits determined by bank address[2:1]

24 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Address Mapping

For IBANK_POS = 3, interleaving among banks within a device (per chip select) is not permitted. Thus, 16
banks (8 internal banks across 2 chip selects) can be kept open at a time, but interleaving among only 2
of them. Table 2-9 shows the address mapping. Address mapping for the desired configuration can be
generated on the lines of Table 2-6.

Table 2-9. Logical Address-to-SDRAM Address Mapping for IBANK_POS = 3

Logical Address [32:N]
Bank Address [2:0] Row Address Chip Select Column Address
IBANK nbb20 ROW SIZE nrb EBANK ncs PAGE SIZE ncb
0 0 bits 0 9 bits 0 0 bits 0 8 bits
1 1 bit 1 10 bits 1 1 bit 1 9 bits
2 2 bits 2 11 bits 2 10 bits
Logical address mapping for Logical address mapping for Logical address mapping for Logical address mapping for
bank_address[2:0] row address chip select column address
MSB LSB MSB LSB MSB LSB MSB LSB
M3+nbb20-1 M3+1 M3=M2+nrb-1 M2+1 M2=M1+ncs-1 M1+1 M1=N+ncb-1 N

The DDR3 memory controller never opens more than one page per bank. The active row is left open until
it becomes necessary to close it, thus decreasing the deactivate-reactivate overhead.
The number of banks between which the controller can interleave is maximum when IBANK_POS=0 and
reduces progressively as IBANK_POS is increased from 1 to 3. Thus, maximum performance is obtained
when IBANK_POS=0. However, to trade off performance for power savings, the application can program
IBANK_POS to a non-zero value.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 25

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Address Mapping www.ti.com

Figure 2-4. Logical Address-to-DDR3 SDRAM Address Map (EBANK=0)

Figure 2-5. DDR3 SDRAM Column, Row, and Bank Access (EBANK=0)

26 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Memory Controller Interface

2.6 DDR3 Memory Controller Interface

To move data efficiently from on-chip resources to an external DDR3 SDRAM device, the DDR3 memory
controller makes use of a Command FIFO, a Write Data FIFO, a Write Status FIFO, a Read Command
FIFO, and two Read Data FIFOs and command and data schedulers. Table 2-10 describes the purpose of
each FIFO. Figure 2-6 shows the block diagram of the DDR3 memory controller FIFOs. Commands, write
data, and read data arrive at the DDR3 memory controller parallel to each other. The same peripheral bus
is used to write and read data from external memory as well as internal memory-mapped registers (MMR).

Table 2-10. DDR3 Memory Controller FIFO Description

FIFO Description Depth
Command Stores all commands coming from on-chip requestors 16
Write Data Stores write data coming from on-chip requestors to memory 20 (512-bit wide)
Write Status Stores the write status information for each write transaction 7
Read Command Stores all read transactions that are to be issued to on-chip requestors 22
SDRAM Read Data Stores read data coming from SDRAM memory to on-chip requestors 22 (256-bit wide)
Register Read Data Stores read data coming from MMRs to on-chip requestors 2 (256-bit wide)

Figure 2-6. DDR3 Memory Controller FIFO Block Diagram

Command Commands
Command FIFO
Scheduler to SDRAM

Data Write data

Write Data FIFO
Scheduler to SDRAM

Write Status FIFO Memory

Control
Mapped
Registers
Data
Read Command FIFO

Register Read Data FIFO

Read data
SDRAM Read Data FIFO
from SDRAM

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 27

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Memory Controller Interface www.ti.com

2.6.1 Arbitration
The DDR3 memory controller performs command reordering and scheduling in an attempt to achieve
efficient transfers with maximum throughput. The goal is to maximize the utilization of the data, address,
and command buses while hiding the overhead of opening and closing DDR3 SDRAM rows. Command
reordering takes place within the command FIFO.
The DDR3 memory controller examines all the commands stored in the command FIFO to schedule
commands to the external memory. For each master, the DDR3 memory controller reorders the
commands based on the following rules:
• The DDR3 controller will advance a read command before an older write command from the same
master if the read is to a different block address (2048 bytes) and the read priority is equal to or
greater than the write priority.
• The DDR3 controller will block a read command, regardless of the master or priority if that read
command is to the same block address (2048 bytes) as an older write command.
Thus, one pending read or write for a master might exist.
• Among all pending reads, the DDR3 controller selects all reads that have their corresponding SDRAM
banks already open.
• Among all pending writes, the DDR3 controller selects all writes that have their corresponding SDRAM
banks already open.
As a result of the above reordering, several pending reads and writes may exist that have their
corresponding banks open. The highest priority read is selected from pending reads, and the highest
priority write from pending writes. If two or more commands have the highest priority, the oldest command
is selected. As a result, there might exist a final read and a final write command. Either the read or the
write command will be selected depending on the value programmed in the Section 4.30.
The DDR3 controller supports interleaving of commands for maximum efficiency. In other words, the
controller will partially execute one command and switch to executing another higher priority command
before finishing the first command.
Apart from reads and writes the DDR3 controller also needs to open and close SDRAM banks, and
maintain the refresh counts for an SDRAM. The priority of SDRAM commands with respect to refresh
levels are as follows:
1. (Highest priority) SDRAM refresh request due to Refresh Must level of refresh urgency reached.
2. Read request without a higher priority write (from the reordering algorithm above)
3. Write request.
4. SDRAM Activate commands.
5. SDRAM Deactivate commands.
6. SDRAM Power-Down request.
7. SDRAM refresh request due to Refresh May or Release level of refresh urgency reached.
8. (Lowest priority) SDRAM self-refresh request.

28 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Memory Controller Interface

2.6.2 Command Starvation

While running the scheduling algorithm described in Section 2.6.1, the DDR3 memory controller is subject
to the following:
1. A continuous stream of high priority commands can block lower priority commands.
2. A continuous stream of SDRAM commands to a row in an open bank can block commands to another
row in the same bank.
To avoid a continuous blocking effect, the priority of the oldest command is momentarily raised over all
other commands when the latency counter for the oldest command expires. The latency counter for the
oldest command (PR_OLD_COUNT) is configurable in the Latency Configuration Register. In addition to
this, the order of command accesses can also be tailored by grouping commands into two categories or
“classes” and assigning different latency expiration counters to each category. See Section 2.6.4 for more
information.
On top of the above scheduling, the highest priority condition is a removal of hard or soft reset. If this
occurs, the DDR3 controller abandons whatever it is currently doing and commences its startup sequence.
In this case, commands and data stored in the FIFOs are lost. The startup sequence also commences
whenever the SDRAM Config register is written and INITREF_DIS field in SDRAM Refresh Control
register (SDRFC) is set to 0. In this case, commands and data stored in the FIFOs are not lost. The DDR3
controller will ensure that in-flight read or write transactions to the SDRAM are complete before starting
the initialization sequence.

2.6.3 Possible Race Condition

A race condition may exist when certain masters write data to the DDR3 memory controller. For example,
if master A passes a software message via a buffer in DDR3 memory and does not wait for indication that
the write completes, when master B attempts to read the software message it may read stale data and
therefore receive an incorrect message. In order to confirm that a write from master A has landed before a
read from master B is performed, master A must wait for the write to complete before indicating to master
B that the data is ready to be read. For example, an EDMA transfer controller should wait for the transfer
completion event to occur before signaling a CorePac to read the message from DDR3.
If master A does not wait for indication that a write is complete, it must perform the following workaround:
1. Perform the required write.
2. Perform a dummy write to the DDR3 memory controller module ID and revision register.
3. Perform a dummy read to the DDR3 memory controller module ID and revision register.
4. Indicate to master B that the data is ready to be read after completion of the read in step 3. The
completion of the read in step 3 ensures that the previous write was done.

2.6.4 Class of Service

The commands in the Command FIFO can be mapped to two classes of service: 1 and 2. The mapping of
commands to a particular class of service can be done based on the priority or the master ID. The
mapping based on priority can be done by setting the appropriate values in the Priority to Class of Service
Mapping register. The mapping based on master ID can be done by setting the appropriate values of
master ID and the masks in the Master ID to Class of Service Mapping registers.
There are three master ID and mask values that can be set for each class of service. In conjunction with
the masks, each class of service can have a maximum of 144 master IDs mapped to it. For example, a
master ID value of 0xFF along with a mask value of 0x3 will map all master IDs from 0xF8 to 0xFF to that
particular class of service. By default all commands will be mapped to class of service 2.
Each class of service has an associated latency counter. The value of this counter can be set in the
Latency Configuration register. When the latency counter for a command expires, i.e., reaches the value
programmed for the class of service that the command belongs to, that command will be the one that is
executed next. If there is more that one command that has expired latency counters, the command with
the highest priority will be executed first. One exception to this rule is as follows: if any of the commands
with the expired latency counters is also the oldest command in the queue, that command will be executed
first irrespective of priority. This is done to prevent a continuous block effect as described in Section 2.6.1.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 29

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Refresh Scheduling www.ti.com

2.7 Refresh Scheduling

The DDR3 controller uses two counters to schedule AUTO REFRESH commands:
• a 13-bit decrementing refresh interval counter
• a four-bit refresh backlog counter
The interval counter is loaded with the REFRESH_RATE field value at reset. The interval counter
decrements by one each cycle until it reaches zero at which point it reloads from REFRESH_RATE and
restarts decrementing. The counter also reloads and restarts decrementing whenever the
REFRESH_RATE field is updated.
The refresh backlog counter records the number of AUTO REFRESH commands that are currently
outstanding. The backlog counter increments by one each time the interval counter reloads (unless it has
reached its maximum value of 15). The backlog counter decrements by one each time the DDR3
controller issues an AUTO REFRESH command (unless it is already at zero). Following a refresh
command, the DDR3 memory controller waits T_RFC cycles, defined in the SDRAM timing 3 register
(SDTIM1), before rechecking the refresh urgency level.
For the range of values that the backlog counter can take, there are three levels of urgency with which the
DDR3 controller should perform an auto refresh cycle (in which it issues AUTO REFRESH commands), as
follows:
• Refresh May level is reached whenever the backlog count is greater than 0, to indicate that there is a
refresh backlog, so if the DDR3 controller is not busy and none of the SDRAM banks are open, it
should perform an auto refresh cycle.
• Refresh Release level is reached whenever the backlog count is greater than 4, to indicate that the
refresh backlog is getting high, so if the DDR3 controller is not busy it should perform an auto refresh
cycle even if any banks are open.
• Refresh Must level is reached whenever the backlog count is greater than 7, to indicate that the refresh
backlog is getting excessive and the DDR3 controller should perform an auto refresh cycle before
servicing any new memory access requests.
The DDR3 controller starts servicing new memory accesses after Refresh Release level is cleared. If any
of the commands in the Command FIFO have class-of-service latency counters that are expired, the
DDR3 controller will not wait for Refresh Release level to be cleared but will only perform one refresh
command and exit the refresh state.
The refresh counters do not operate when SDRAM has been put into self-refresh mode. Also, the refresh
counters start tracking the missed refreshes only after initialization is complete.

2.8 Self-Refresh Mode

The DDR3 memory controller supports self-refresh mode for low power. The controller maintains
DDRCKE low to maintain the self-refresh state. In self-refresh, the memory maintains valid data while
consuming a minimal amount of power.
Self-refresh mode is set by programming the LP_MODE in the Power Management Control register
(PMCTL) to 2. The controller automatically puts the SDRAM into self-refresh after the controller is idle for
SR_TIM DDR3CLKOUT cycles. (See Section 4.8 for more information.)
The memory is brought out of self-refresh under any of the following conditions:
• If the LP_MODE field is set not equal to 2
• A memory access is requested
• SR_TIM bit in PMCTL is cleared
In a situation where memory accesses and a self-refresh command are sent to the DDR3 memory
controller, the controller always prioritizes the memory access. Thus, if a reset is triggered when memory
accesses and a self-refresh command are queued in the controller, it is likely that self-refresh will not be
entered.
The user must ensure that all memory accesses have been completed, and verify that self-refresh is set in
the STATUS register before initiating a reset.

30 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Self-Refresh Mode

NOTE: The DDR3 memory controller completes all pending memory accesses and refreshes before
it puts SDRAM into self-refresh. If a request for a memory access is received, the DDR3
memory controller services the memory access request then returns to the self-refresh state
upon completion.

CAUTION
A special case may exist where the DDR3 controller violates the DDR3 JEDEC
standard by issuing excessive refreshes (more than 16) within twice the tREFI
interval when in self refresh mode. A workaround exists to conform to the
JEDEC standard. Refer to the Errata document for your device for the advisory
and workaround.

2.8.1 Extended Temperature Range

The normal operating temperature range for DDR3 SDRAMs is typically 0 to 85°C. When operating in self-
refresh mode within the extended temperature range (85°C to 95°C), the memory device must be
refreshed at 2× the normal refresh rate. For this purpose, either the auto self-refresh (ASR) or self-refresh
temperature (SRT) feature should be used. Under normal operating conditions, both ASR and SRT should
be disabled (equal to 0). When ASR is enabled, the internal refresh rate of the SDRAM automatically
switches to 2× the refresh rate when the operating case temperature Tc is greater than 85°C when in Self-
refresh mode. When SRT is enabled, the internal refresh rate of the SDRAM is forced to 2× the refresh
rate regardless of Tc. Both SRT and ASR cannot be enabled at the same time. One must be disabled if
the other is enabled.

NOTE: ASR and SRT are used only in self-refresh mode (LP_MODE=0×2). When operating in
extended temperature range with LP_MODE = 0×0 (not in self-refresh), it is up to the user to
program the manual refresh rate to 2× the normal refresh rate for proper operation. If it is
guaranteed that Tc will exceed 85°C, it is recommended that SRT=1 to force the refresh rate
to 2× regardless of operating temperature.

2.9 Reset Considerations

The DDR3 memory controller can be reset through a hard reset or a soft reset. A hard reset resets the
state machine, the FIFOs, and the internal registers. A soft reset only resets the state machine and the
FIFOs. A soft reset does not reset the internal registers except for the interrupt registers. Register
accesses cannot be performed while either reset is asserted.
The DDR3 memory controller hard and soft reset are derived from device-level resets. Table 2-11 shows
the relationship between the device-level resets and the DDR3 memory controller resets. For more
information on the device-level resets, see the device-specific data manual.

Table 2-11. Device and DDR3 Memory Controller Reset Relationship

DDR3 Memory Controller Reset Effect Initiated by
Hard reset Resets control logic and all DDR3 memory • Please refer to the reset controller
controller registers description in your device data manual
Soft reset Resets control logic and interrupt registers • Please refer to the reset controller
description in your device data manual

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 31

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Turnaround Time www.ti.com

2.10 Turnaround Time

Table 2-12 shows the turn around time that the DDR3 memory controller introduces on the data bus for
various back-to-back accesses. Note that the DDR3 memory controller takes advantage of the CAS
latencies and packs the commands as close as possible on the control bus to introduce the following turn
around time on the data bus.

Table 2-12. Turnaround Time

Previous Access Next Access Turnaround Time (DDR3 memory clock cycles)
SDRAM Write SDRAM Write to same chip select 0
SDRAM Write SDRAM Write to different chip select T CSTA + 1
SDRAM Read SDRAM Read to same chip select 0
SDRAM Read SDRAM Read to different chip select T CSTA + 1
SDRAM Write SDRAM Read T WTR + 1 + CL
SDRAM Read SDRAM Write T_RTW + 1

2.11 DDR3 SDRAM Memory Initialization

DDR3 SDRAM initialization is achieved by programming memory mapped registers in the DDR3 controller
configuration space and the Bootcfg space in a specific sequence. The software programming sequence
is described in the Keystone I DDR3 Initialization Application Note. This sequence of software
programming steps, causes the controller to issue MRS and EMRS commands to program mode and
extended mode registers in the SDRAM device. These registers control parameters such as burst type,
burst length, and CAS latency. The sequence of commands during the initialization sequence described in
Section 2.11.1. The initialization sequence performed by the DDR3 memory controller is compliant with
the JESD79-3C specification.
The DDR3 memory controller performs the initialization sequence under the following conditions:
• Automatically following a hard or soft reset (see Section 2.11.1)
• Following a write to the SDRAM configuration register (SDCFG) (see Section 2.11.1)
At the end of the initialization sequence, the DDR3 memory controller performs an auto-refresh cycle,
leaving the DDR3 memory controller in an idle state with all banks deactivated.
During the initialization sequence, the DDR3 memory controller issues MRS and EMRS commands that
configure the DDR3 SDRAM mode registers with the values described in Table 2-13 and Table 2-14.
When a reset occurs, the DDR3 memory controller immediately begins the initialization sequence. Under
this condition, commands and data stored in the DDR3 memory controller FIFOs will be lost. However,
when the initialization sequence is initiated by a write to the SDCFG Register, data and commands stored
in the DDR3 memory controller FIFOs will not be lost and the DDR3 memory controller will ensure read
and write commands are completed before starting the initialization sequence.
As the default values of the Mode Register (MR) and extended mode registers 1, 2, 3 are not defined,
contents of Mode/Extended Mode Registers must be fully initialized and/or reinitialized, i.e., written, after
power up and/or reset for proper operation. Also the contents of the Mode/Extended Mode Registers can
be altered by re-executing the MRS/EMRS command during normal operation. The mode/extended mode
registers are selected by varying the bank address bits BA [1:0]. BA [2] and A [15:13] are reserved for
future use and must be programmed to zero.
The extended mode register 3 is configured with a value of 0h.

32 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 SDRAM Memory Initialization

Table 2-13. DDR3 SDRAM Extended Mode Register 2 Configuration (1)

Mode Register Mode Register
Bit Field Init Value Description
15-11 Reserved 0x0 Reserved
10-9 Rtt_WR SDCFG.DYN Dynamic ODT value from SDRAM Config Register
_ODT
8 Reserved 0x0 Reserved
7 SRT SDRCR.SRT Self-Refresh temperature range from SDRAM Refresh Control register
6 ASR SDRCR.ASR Auto self-refresh enable from SDRAM Refresh Control register
5-3 CWL SDCFG.CWL CAS write latency from SDRAM Config register
2-0 PASR SDRCR.PASR Partial array self-refresh from SDRAM Refresh Control register
(1)
Bank Address bits to select EMR 2 are BA [1:0] = 0x2.

Table 2-14. DDR3 SDRAM Extended Mode Register 1 Configuration (1)

Mode Register
Bit Mode Register Field Init Value Description
12 Qoff 0x0 Output Buffer Enabled
11 TDQS 0x0 TDQS enable/disable
10 Reserved 0x0 Reserved
9 Rtt_nom SDCFG.DDRTERM[2] DDR3 termination resistor value from SDRAM Config
register
8 Reserved 0x0 Reserved
7 Level 0x0 Write Leveling Disabled
6 Rtt_nom SDCFG.DDRTERM[1] DDR3 termination resistor value from SDRAM Config
register
5 Output driver impedance SDCFG.SDRAM SDRAM drive strength from SDRAM Config register
_DRIVE[1]
4-3 Additive Latency 0x0 Additive latency = 0
2 Rtt_nom SDCFG.DDRTERM [0] DDR3 termination resistor value from SDRAM Config
register
1 Output driver impedance SDCFG.SDRAM SDRAM drive strength from SDRAM Config register
_DRIVE[0]
0 DLL Enable 0x0 DLL enable/disable from SDRAM Config register
(1)
Bank Address bits to select EMR 1 are BA [1:0] = 0x1.

Table 2-15. DDR3 SDRAM Mode Register 0 Configuration (1)

Mode Register Bit Mode Register Field Init Value Description
12 DLL control for Precharge PD 0x0 Fast exit active powerdown exit time
11-9 Write Recovery SDTIM1.T_WR Write recovery for auto precharge from
SDAM Timing 1 Register
8 DLL Reset 0x1 DLL Reset
7 Mode 0x0 Normal Mode from SDRAM Config
Register
6-4 CAS Latency SDCFG.CL[3:1] CAS Latency from SDRAM Config
Register
3 Read Burst Type 0x0 sequential/interleave burst type
2 CAS Latency SDCFG.CL[0] CAS Latency from SDRAM Config
Register
1-0 Burst length 0x0 Burst length of 8
(1)
Bank Address bits to select MR are BA [1:0] = 0x0.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 33

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 SDRAM Memory Initialization www.ti.com

2.11.1 DDR3 Initialization Sequence

On coming out of reset if the SDRAM_TYPE field in the SDRAM Config register is equal to 3 and the
INITREF_DIS bit in the SDRAM Refresh Control register is set to 0, the DDR3 Controller performs a
DDR3 SDRAM initialization sequence. The sequence follows the JEDEC standard. Please refer to the
JEDEC spec for the initialization sequence.
The DDR3 memory controller also performs the initialization sequence whenever the SDRAM Config
register is written. But in this case, the sequence starts at step 3. The DDR3 memory controller does not
perform any transactions until the DDR3 initialization sequence is complete.

2.12 Dual Rank Support

The Keystone-I device also offers dual rank support. The device uses both chip selects (DCE0 and
DCE1), with each chip select enabling access to one of the two SDRAM ranks. To enable dual rank
access:
1. Set use_rank0_delays bit in the DDR3_CONFIG_12 register to 1. This directs the PHY leveling logic to
use one set of optimal leveling values to access both ranks. This write must immediately follow the
completion of the leveling process.
2. Set the EBANK bit in the SDCFG register to 1. This directs the controller to use both chip selects, one
for each rank.
See the section on Dual Rank Support in the Keystone-I DDR3 Initialization App note for the proper
sequence of initialization steps. Although dual rank access is supported, address mirroring is not.

2.13 Leveling
The DDR3 controller supports a new feature called leveling to compensate for the command and DQS
skew as a result of the fly-by topology. Leveling compensates the skew for both reads and writes. Both full
leveling and incremental leveling are supported. The controller does not perform full leveling after
initialization. It must be first enabled by software after initialization.

2.13.1 Full Leveling (Auto Leveling)

Full leveling or auto leveling consists of write leveling, read data eye training and read DQS gate training.
Write leveling is used to compensate for the command-to-DQS delay for writes. Read DQS gate training is
used by the internal DDR3 controller logic before read data eye leveling to determine the most appropriate
time to ensure a valid DQS coming into the DDR3 controller from the SDRAM. Read data eye training
then tries to align the valid DQS to the center of the DQ line for reads by adjusting the DQS delay relative
to DQ.
Leveling (both full and incremental) can be enabled by writing a '1' to the RDWRLVL_EN field in the Read-
Write Leveling Ramp Control register (RDWR_LVL_RMP_CTRL). Once enabled, full leveling can be
triggered by writing a ‘1’ to the RDWRLVLFULL_START bit in the Read-Write Leveling Control Register
(RDWR_LVL_CTRL). Once triggered, all three full levelings (write leveling, read DQS gate training and
read data eye training) will be performed. Thus there is no independent control over individual leveling
types for full leveling.

NOTE: Full leveling violates the refresh interval; data inside DDR3 can be lost if full leveling is
performed during normal operation. It is recommended that full leveling be performed after
initialization and before any transactions to the DDR3 memory device are initiated. Any
subsequent full leveling will not guarantee the data integrity inside the memory. During
normal operation, temperature and voltage can be better tracked by incremental leveling.

34 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Leveling

2.13.2 Incremental Leveling

Incremental leveling is a feature that can be used to track voltage and temperature (V-T) changes over
time as these can negatively impact the DQS de-skewing process that has occurred after full leveling.
After performing full leveling once, incremental leveling can be performed periodically to more accurately
track V-T drifts. Incremental leveling allows for greater control over the individual leveling types - write,
read DQS gate and read data eye. Each of these levelings can be programmed to occur at a different
rate. The rate is measured in terms of refresh periods. RDWRLVLINC_PRE is the base period defined in
terms of number of refresh intervals. WRLVLINC_INT, RDLVLGATEINC_INT, and RDLVLINC_INT fields
in the RDWR_LVL_CTRL register can be used to program independent leveling intervals (in number of
the base period) for write leveling, gate training and read data eye leveling respectively. The respective
leveling is triggered when its interval expires.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 35

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Leveling www.ti.com

2.13.2.1 Ramp Incremental Leveling

What was described above can be referred to as standalone incremental leveling which is software-
triggered. Ramp incremental leveling can only be used for DSPs that support Smart-reflex Class-3 (SR
Class-3). Because SR Class-3 is not supported by Keystone-I devices, the ramp incremental leveling
feature is also not supported.

2.13.3 Impact On Bandwidth

The DDR3 controller does not perform any reads/writes during incremental leveling. So a faster
incremental leveling rate will have a larger impact on throughput than programming a smaller rate. Also,
programming the intervals such that they all don’t expire at the same time can minimize the impact on
bandwidth.

NOTE: At this time there are no “best practices” recommendations for setting the incremental
leveling intervals. The choice is entirely up to the application depending on the bandwidth
tradeoff and environmental conditions expected.

2.13.4 Programming Full Leveling

Leveling (both full and incremental) is executed separately for each byte lane (clock-DQS pair). Therefore,
the leveling process converges separately for each byte lane. To ensure that leveling converges correctly,
the DDR3 controller must be given an initial set of values to use during leveling. The leveling process uses
these initial values to arrive at a set of converged values for each byte lane. These initial values should be
plugged into a set of memory-mapped registers in the Boot configuration section.
The user should note that the DATAx registers in steps 2 and 3 below map to specific byte lanes as
follows (note the difference between C665x and other device variants). The mapping is consistent for write
leveling and gate leveling initial values i.e. DATA n_PHY_WRLVL_INIT_RATIO and DATA
n_PHY_GATELVL_INIT_RATIO map to the same byte lane. DATA m_PHY_WRLVL_INIT_RATIO and
DATA m_PHY_GATELVL_INIT_RATIO map to the same byte lane.

Table 2-16. DATAx register to byte lane mapping

Register C665x devices (36-bit) All other Keystone-I devices (72-bit)
DATA0_* Byte lane 3 Byte lane 7
DATA1_* Byte lane 2 Byte lane 6
DATA2_* Byte lane 1 Byte lane 5
DATA3_* Byte lane 0 Byte lane 4
DATA4_* NA Byte lane 3
DATA5_* NA Byte lane 2
DATA6_* NA Byte lane 1
DATA7_* NA Byte lane 0
DATA8_* ECC Byte lane ECC Byte lane

36 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Leveling

The steps to program full leveling are as follows:

1. Unlock the Boot configuration module by writing 0x83E70B13 to the KICK0 and 0x95A4F1E0 to the
KICK1 registers.
2. Program the write leveling initial values into the DATA0_PHY_WRLVL_INIT_RATIO to
DATA8_PHY_WRLVL_INIT_RATIO fields of the DDR3_CONFIG_2 to DDR3_CONFIG_10 registers
respectively. (See the tables in sections Section 4.33 to Section 4.41).

NOTE: The values to enter into the registers depend on the board topology and the DDR3 clock
frequency in use. The DDR3 clock frequency (half the data rate) and trace lengths for each
byte lane (CK-DQS pair) should be plugged in the appropriate fields in the accompanying
PHY calculation spreadsheet which generates the values to be programmed into the boot
config registers mentioned above.

3. Program the gate leveling initial values into the DATA0_PHY_GATELVL_RATIO to

DATA8_PHY_GATELVL_RATIO fields of the DDR3_CONFIG_14 to DDR3_CONFIG_22 registers
respectively. (See the tables in sections Section 4.43 to Section 4.51.)

NOTE: The values to enter into the registers depend on the board topology and the DDR3 clock
frequency in use. The DDR3 clock frequency (half the data rate) and trace lengths for each
byte lane (CK-DQS pair) should be plugged in the appropriate fields in the accompanying
PHY calculation spreadsheet which generates the values to be programmed into the boot
config registers mentioned above.

4. Program CMD_PHY_DLL_LOCK_DIFF field in DDR3_CONFIG_0 register to 0xF.

(See Section 4.31.)
5. Enable global leveling (Set RDWRLVL_EN = 1 in RDWR_LVL_RMP_CTRL).
6. Trigger full leveling (Set RDWRLVLFULL_START = 1 in RDWR_LVL_CTRL).
7. Read back any of the DDR3 controller registers.
This ensures full leveling is complete because this step is executed only after full leveling completes.

2.13.4.1 Leveling Timeout

The DDR3 controller attempts to converge to the correct leveling values within a reasonable time frame
after full leveling is triggered. If a leveling type (write, gate or read data eye) does not converge within the
time frame the controller will leave in the unconverged values for each byte lane which will affect DDR3
stability since the de-skew will not be accurate. In such a case, a timeout bit for that leveling will be set in
the SDRAM Status Register (WRLVLTO, RDLVLGATETO, and RDLVLTO). The timeouts are global
values for all byte lanes that will be set even if one of the byte lanes times out. Plugging in incorrect initial
values for a byte lane can typically result in a timeout.

2.13.4.2 Read Data Eye Training Errata For Full Leveling

On certain KeyStone DSPs, the read data eye training has issues converging to the correct values during
the full leveling process. See the device-specific Errata document for this and other advisories and usage
notes.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 37

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Leveling www.ti.com

2.13.5 Programming Incremental Leveling

This assumes that global leveling is enabled (RDWRLVL_EN=1) and full leveling has already been
performed.

2.13.5.1 Standalone Incremental Leveling

Steps to program standalone incremental leveling are:
1. Program RDWRLVLINC_PRE to set the pre-scalar in terms of refresh intervals.
2. Program non-zero values for WRLVLINC_INT, RDLVLGATEINC_INT, and RDLVLINC_INT to decide
each of the leveling intervals.
3. Step 2 will trigger incremental leveling. To disable a type of incremental leveling, just program its
interval to zero.

2.13.6 Programming Ratio Forced Leveling

The user can disable auto leveling and instead use a set of ratio forced register values present in
Section 4.52 and Section 4.53 for devices other than C665x and TCI6612/13/14. These values control the
DQ and DQS delay for all byte lanes for write leveling, read DQS gate training and read data eye training.
Similar to auto-leveling, these values also depend on board characteristics (trace lengths) and the DDR3
frequency of operation.
For devices other than C665x and TCI6612/13/14, independent control over each byte lane is not
possible. A single value needs to be used for all byte lanes. Thus the DQ and DQS skews across byte
lanes must be very small. The values to be programmed are WR_DATA_SLAVE_RATIO,
WR_DQS_SLAVE_RATIO, RD_DQS_SLAVE_RATIO, and FIFO_WE_SLAVE_RATIO and can be found
in the PHY calculation spreadsheet.
For C665x and TCI6612/13/14 devices, independent control is possible over each byte lane through
registers DDR3_CONFIG_REG_25 through DDR3_CONFIG_REG_60.

2.13.7 Using Invert Clock Out

For write leveling (both full and incremental) to function correctly, the skew between command and data
lines from DSP to an SDRAM should satisfy certain command-to-data skew requirements. The skew is
defined as follows:
• write_levelingskew = commanddelay - datadelay.
Both commanddelay and datadelay are measured from the DSP to the SDRAM.
The JEDEC standard parameters tJIT (per, lck) and tWLS defined as the clock period jitter when DLL is
locking and write leveling setup time respectively, demand a minimum write_levelingskew that must be
satisfied. The minimum skew is a function of the DDR3 speed bin that is being used. If write_levelingskew is
greater than the minimum skew, CMD_PHY_INVERT_CLKOUT in DDR3_CONFIG_12 register can be left
to its default value of 0. If write_levelingskew is smaller than the minimum required skew,
CMD_PHY_INVERT_CLKOUT should be set to 1. This essentially adds a half-clock cycle delay to the
write_levelingskew and thus increases the skew above the minimum skew requirements.

38 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Interrupt Support

Similar to the minimum skew requirements, there also exists a maximum skew that cannot be exceeded
for the write leveling algorithm to function correctly. Maximum skew is also a function of the DDR3 speed
bin in use. Both minimum and maximum skews have routing implications for command and data lines. For
min/max routing limits with CMD_PHY_INVERT_CLKOUT = 0 or 1, refer to the DDR3 Design Guide
(SPRABI1A).

NOTE: When setting CMD_PHY_INVERT_CLKOUT to 1, the CMD_PHY_CTRL_SLAVE_RATIO

field in DDR3_CONFIG_0 should be programmed to 0x100. If set to 0, program the default
value of 0x80.

NOTE: From the equation, if command lines are shorter than the data lines the resulting skew will
be negative. There is a maximum negative skew that the write leveling algorithm can
tolerate. For more information refer to the DDR3 Design Guide (SPRABI1A)

2.14 Interrupt Support

The DDR3 memory controller generates one error interrupt. Please check the section on interrupts in the
device data manual for details on how the ECC error interrupt is routed. The source of the interrupt can be
checked in the Interrupt Raw Status Register.

2.15 EDMA Event Support

The DDR3 memory controller is a DMA slave peripheral and therefore does not generate EDMA events.
Data read and write requests may be made directly by masters including the EDMA controller.

2.16 Emulation Considerations

The DDR3 memory controller will remain fully functional during emulation halts to allow emulation access
to external memory.

2.17 ECC
For data integrity, the DDR3 memory controller supports ECC on the data written to or read from the ECC
protected address ranges in memory. The ECC algorithm is a single-error-correct-double-error-detect
(SECDED) algorithm and uses the (72,64) Hamming code. Eight-bit ECC is calculated over 64-bit data
quanta. ECC is enabled by setting ECC_EN = 1 in the ECC Control register. ECC is disabled by setting
ECC_EN=0. By default, ECC_EN=0. The address ranges can be programmed in the ECC Address Range
1 and 2 register. The system must ensure that any bursts accesses starting in the ECC protected region
must not cross over into the unprotected region and vice-versa.

NOTE: The ECC is stored inside the SDRAM during writes. After enabling ECC and before
performing any functional reads or writes, all DDR3 memory space configured as ECC
should be first written with known data that is 64-bit aligned and multiples of 64-bit. This is to
ensure the correct ECC values are stored in the ECC SDRAM prior to functional use.

A write access with byte count that is not a multiple of 64-bit quanta, or with a non-64-bit-aligned address
performed within the address range protected by ECC, will result in a write ECC error interrupt. In this
case, the DDR3 memory controller writes to the SDRAM. However, the ECC value written to the SDRAM
will be corrupted. The controller will NOT trigger a write ECC error if a write access with a multiple of 64-
bit quanta and with 64-bit aligned address but with partial byte enables set, is performed within the
address range protected by ECC (this can be the case if the Multicore Navigator PktDMA writes to a
descriptor placed in DDR3). The data and corrupted ECC value will be written to the SDRAM, but will go
undetected and may be detected as 1-bit or 2-bit errors when read back.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 39

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Power Management www.ti.com

If there is a one-bit error, the DDR3 memory controller corrects the data and sends it on the read
interface. For 2-bit errors, the DDR3 memory controller generates a read ECC error interrupt. Note that in
both cases, the data in SDRAM is still corrupted. It is the responsibility of system software to go and
correct the data in the SDRAM.

NOTE: The user should note that the single error correct, double error detect (SECDED) algorithm
used by the ECC logic cannot detect more than 2-bit errors per 64-bit quanta. For these
errors, the output of the algorithm is unknown i.e. it may erroneously detect as 1-bit, 2-bit or
no errors. More than 2-bit errors are expected to be very rare in a well designed system.

See Section 4.27 through Section 4.29 for ECC-related registers.

NOTE: If ECC is disabled, the ECC byte lane is held in reset to save power. Hence, full-leveling
must be triggered after enabling ECC to ensure that the ECC byte lane is leveled.

2.18 Power Management

2.18.1 SDRAM Self-Refresh Mode

(See Section 2.8.)

2.18.2 SDRAM Power-Down Mode

The DDR3 memory controller supports power-down mode. Automatic power-down is enabled by setting
the LP_MODE field in the Power Management Control register (PMCTL) to 4. The memory is put into
power-down after the controller is idle for PD_TIM number of DDR3CLKOUT cycles. In power-down mode,
the DDR3 memory controller does not stop the clocks to the memory. The controller maintains DDRCKE
low to maintain the power-down state. When the SDRAM is in power-down, the DDR3 memory controller
services register accesses as normal.
The memory is brought out of power-down under any of the following conditions:
• If the LP_MODE field is set not equal to 4
• A memory access is requested
• Refresh Must level is reached

2.19 Performance Monitoring

The DDR3 controller provides a set of performance counter registers which can be used to monitor or
calculate the bandwidth and efficiency of the DDR traffic. The counters can be configured to count events
such as total number of SDAM accesses, SDRAM activates, reads, write and so on. The Performance
Counter 1 and 2 Registers (PERF_CNT_1 and PERF_CNT_2) act as two 32-bit counters that are able to
count events independent of each other. To provide more granularity the counters can also be configured
to filter events originating from a particular master or address space. The events to be counted and filter
enabled are programmed in the Performance Counter Config Register (PERF_CNT_CFG). The actual
value of the filter is programmed in Performance Counter Master Region Select Register
(PERF_CNT_SEL). The counters start counting the events independently when commands enter the
Command FIFO.
The CNTRN_CFG (N=1,2) fields in the PERF_CNT_CFG register are used to select the event for the
counter to count. The PERF_CNT_CFG also includes options to enable or disable the master
(CNTRN_MSTID_EN) and address space (CNTRN_REGION_EN) filters for each counter. The filters are
disabled by default. If the respective filters are enabled, the master ID value and region select options can
be programmed in the PERF_CNT_SEL register. It should be noted that the master ID and region select
filters apply only to a certain subset of events that can be counted. The table below shows the events for
which the filters are applicable.

40 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Performance Monitoring

Table 2-17. Performance Counter Filter Configuration

PERF_CNT_CFG. PERF_CNT_CFG. PERF_CNT_CFG.
[CNTR_CFG] Event Selected for counting [CTNR_REGION_EN] [CNTR_MSTID_EN]
0x0 Total SDRAM accesses NA 0 - Disable,
1 - Enable
0x1 Total SDRAM activates NA 0 - Disable,
1 - Enable
0x2 Total Reads 0 - Disable, 0 - Disable,
1 - Enable 1 - Enable
0x3 Total Writes 0 - Disable, 0 - Disable,
1 - Enable 1 - Enable
0x4 Number of DDR/2 clock cycles Command FIFO is full NA NA
0x5 Number of DDR/2 clock cycles Write Data FIFO is full NA NA
0x6 Number of DDR/2 clock cycles Read Data FIFO is full NA NA
0x7 Number of DDR/2 clock cycles Write Status FIFO is full NA NA
0x8 Number of priority elevations 0 - Disable, 0 - Disable,
1 - Enable 1 - Enable
0x9 Number of DDR/2 clock cycles that a command was pending NA NA
0xA Number of DDR/2 clock cycles for which DDR i/f was NA NA
transferring data
0xB Total number of 1-bit ECC errors NA NA
0x C - 0XF Reserved

See Chapter 4 for details on Performance counter registers.

SPRUGV8E – November 2010 – Revised January 2015 Peripheral Architecture 41

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Performance Monitoring www.ti.com

42 Peripheral Architecture SPRUGV8E – November 2010 – Revised January 2015

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 Chapter 3
SPRUGV8E – November 2010 – Revised January 2015

Using the DDR3 Memory Controller

The following sections show various ways to connect the DDR3 memory controller to DDR3 memory
devices. The steps required to configure the DDR3 memory controller for external memory access are
also described.

Topic ........................................................................................................................... Page

3.1 Connecting the DDR3 Memory Controller to DDR3 SDRAM ..................................... 44

3.2 Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM
Specifications .................................................................................................... 48

SPRUGV8E – November 2010 – Revised January 2015 Using the DDR3 Memory Controller 43
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Connecting the DDR3 Memory Controller to DDR3 SDRAM www.ti.com

3.1 Connecting the DDR3 Memory Controller to DDR3 SDRAM

The following figures show high-level views of the three memory topologies:
• Figure 3-1
• Figure 3-2
• Figure 3-3
All DDR3 SDRAM devices must comply with the JESD79-3C standard.
Not all of the memory topologies shown may be supported by your device. For more information, see the
device-specific data manual.
The printed-circuit-board (PCB) layout rules and connection requirements between the DSP and the
memory device are described in a separate document. For more information, see the device-specific data
manual.

44 Using the DDR3 Memory Controller SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Connecting the DDR3 Memory Controller to DDR3 SDRAM

Figure 3-1. Connecting Two 16 MB x 16 x 8 Banks (4Gb Total) Devices

DDR3CLKOUTP0 CK
DDR3CLKOUTN0 CK#
DDRCKE0 CKE
DDRCE0 CS#
DDRWE WE#
DDRRAS RAS#
DDRCAS CAS#
DDRDQM0 DM0
DDRDQM1 DM1 DDR3
Memory
x 16-bit
DQS0
DDRDQS0P
DQS0#
DDRDQS0N
DQS1
DDRDQS1P
DQS1#
DDRDQS1N

DDR3
DDRBA [2:0] BA [2:0]
Memory
DDRA [13:0] A [13:0]
Controller
DDRD [15:0] DQ [15:0]
V REF ODT
VREF

DDRRESETz RESET#

CK
CK#
CKE
CS#
WE#
RAS#
CAS#
DDRDQM2 DM0
DDRDQM3 DM1 DDR3
Memory
x 16-bit
DQS0
DDRDQS2P
DQS0#
DDRDQS2N
DQS1
DDRDQS3P DQS1#
DDRDQS3N

DDRD [31:16] BA [2:0]

DDRODT0 A [13:0]
DDRODT1 DQ [15:0]
DDRSLRATE [1:0] VDD ODT
VREF
RESET#

SPRUGV8E – November 2010 – Revised January 2015 Using the DDR3 Memory Controller 45
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Connecting the DDR3 Memory Controller to DDR3 SDRAM www.ti.com

Figure 3-2. Connecting One 8 MB x 16 x 8 Banks (1Gb Total) Device

DDR3CLKOUT0P CK
DDR3CLKOUT0N CK#
DDRCKE0 CKE
DCE0 CS#
DDRWE WE#
DDRRAS RAS#
DDRCAS CAS#
DDRDQM0 DM0
DDRDQM1 DM1 DDR3
Memory
x16-bit
DDRDQS0P
DQS0
DDRDQS0N
DQS0#
DDRDQS1P DQS1
DDRDQS1N DQS1#
DDR3
Memory
Controller DDRBA [2:0] BA [2:0]
DDRA [12:0] A [12:0]
DDRD [15:0] DQ [15:0]
DDRODT0 ODT
DDRODT1 x
DDRSLRATE [1:0] VDD VREF
V REF

DDRRESET RESET#

46 Using the DDR3 Memory Controller SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Connecting the DDR3 Memory Controller to DDR3 SDRAM

Figure 3-3. Connecting Two 16 MB x 8 x 8 Banks (2Gb Total) Devices

DDR3CLKOUT0P CK
DDR3CLKOUT0N CK#
DDRCKE0 CKE
DCE0 CS#
DDRWE WE#
DDRRAS RAS#
DDRCAS CAS#
DDRDQM0 DM0

DDRDQS0P DQS0
DDRDQS0N DQS0#

DDR3
Memory
DDR3 x 8-bit
Memory
Controller

DDRBA [2:0] BA [2:0]

DDRA [13:0] A [13:0]
DDRD [7:0] DQ [7:0]
V REF
ODT
VREF

DDRRESET RESET#

CK
CK#
CKE
CS#
WE#
RAS#
CAS#
DDRDQM1 DM0

DDRDQS1P DQS0
DDRDQS1N DQS0#

DDR3
DDRD [15:8] Memory
DDRODT0 x 8-bit
DDRODT1
DDRSLRATE [1:0] VDD

BA [2:0]
A [13:0]
DQ [7:0]
ODT
VREF

RESET#

SPRUGV8E – November 2010 – Revised January 2015 Using the DDR3 Memory Controller 47
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM Specifications www.ti.com

3.2 Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM Specifications
The DDR3 memory controller allows a high degree of programmability for shaping DDR3 accesses. This
provides the DDR3 memory controller with the flexibility to interface with a variety of DDR3 devices. By
programming the SDRAM Configuration Register (SDCFG), SDRAM Refresh Control Register (SDRFC),
SDRAM Timing 1 Register (SDTIM1), SDRAM Timing 2 Register (SDTIM2) and SDRAM Timing 3
Register (SDTIM3), the DDR3 memory controller can be configured to meet the data sheet specification
for JESD79-3C compliant DDR3 SDRAM devices.
As an example, the following sections describe how to configure each of these registers for access to two
1 Gb, 16-bit wide DDR3 SDRAM devices connected as shown on Figure 3-2, where each device has the
following configuration:
• Maximum data rate: 1333 MHz
• Number of banks: 8
• Page size: 1024 words
• CAS latency: 9
It is assumed that the frequency of the DDR3 memory controller clock (DDR3CLKOUT) is set to
666.5 MHz.

3.2.1 Programming the SDRAM Configuration Register (SDCFG)

The SDRAM configuration register (SDCFG) contains register fields that configure the DDR3 memory
controller to match the data bus width, CAS latency, number of banks, and page size of the attached
DDR3 memory.
Table 3-1 shows the resulting SDCFG configuration.

Table 3-1. SDCFG Configuration

Field Value Function Selection
SDRAM_TYPE 0x3h SDRAM Type Select – DDR3
NM 1h To configure the DDR3 memory controller for a 32-bit data bus width.
CL 10h To select a CAS latency of 9.
IBANK 3h To select 8 internal DDR3 banks.
EBANK 0 To select only DCE0z to be used.
PAGESIZE 2h To select 1024-word page size.

3.2.2 Programming the SDRAM Refresh Control Register (SDRFC)

The SDRAM refresh control register (SDRFC) configures the DDR3 memory controller to meet the refresh
requirements of the attached DDR3 device. SDRFC also allows the DDR3 memory controller to enter and
exit self refresh.
The REFRESH_RATE field in SDRFC is defined as the rate at which the attached DDR3 device is
refreshed in DDR3 cycles. The value of this field may be calculated using the following equation:
REFRESH_RATE = DDR3CLKOUT frequency × memory refresh period (1)
According to the DDR3 JEDEC standard, on reset de-assertion the DDRCKE pin must remain low for at
least 500µs before becoming active during power-up initialization. This is achieved by programming a 500
µs refresh period in the SDRFC prior to initialization.
Table 3-2 shows the DDR3-1333 refresh rate specification.

Table 3-2. DDR3 Memory Refresh Specification

Symbol Description Value
tREFI Refresh interval to be programmed during power-up initialization 500 µs
tREFI Average Periodic Refresh Interval (after power-up initialization) 7.8 µs

48 Using the DDR3 Memory Controller SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM Specifications

The refresh rate of 500 µs to be programmed during power-up initialization should be calculated equal to a
divide-by-16 value as follows. The DDR3 controller takes care of the divide-by-16 internal logic.
REFRESH_RATE = (666.5 MHz × 500 µs)/16 = 515Ch (2)
After power-up initialization, the refresh rate of 7.8 µs should be programmed as follows:
REFRESH_RATE = 666.5 MHz × 7.8 µs = 1450h (3)
Table 3-3 shows the resulting SDRFC configuration.

Table 3-3. SDRFC Configuration

Field Value Function Selection
SRT 0 Normal Operating Temperature Range
ASR 0 Manual Self-Refresh
REFRESH_RATE 515Ch Set a divide-by-16 equivalent of 500 µs during power-up initialization.
1450h Set to 1450h DDR3 clock cycles to meet the DDR3 memory refresh rate requirement during normal
opertion.

3.2.3 Configuring SDRAM Timing Registers (SDTIM1, SDTIM2, SDTIM3, SDTIM4)

The SDRAM timing 1 register (SDTIM1), SDRAM timing 2 register (SDTIM2), SDRAM timing 3 register
(SDTIM3), SDRAM timing 4 register (SDTIM4) configure the DDR3 memory controller to meet the
datasheet timing parameters of the attached DDR3 device. Each field in SDTIM1, SDTIM2, SDTIM3,
SDTIM4 corresponds to a timing parameter in the DDR3 datasheet specification. Table 3-4, Table 3-5,
and Table 3-6 show the register field name and corresponding DDR3 datasheet parameter name and
value. These tables also provide a formula to calculate the register field value and show the resulting
calculation. Each of the equations includes a minus 1 because the register fields are defined in terms of
DDR3 clock cycles minus 1. (See Section 4.5- Section 4.7 for more information.). Some of these timing
parameters will also have to be programmed in the DRAM Timing Parameter Registers (See Section 4.50
- Section 4.52)
The objective behind programming the timing values is to calculate them in terms of DRAM clock
cycles and round off to the next highest integer value. For example, at 666.5 MHz, the clock period
tCK = 1.5 ns. So 13.5 ns will be programmed as (13.5/1.5)-1= 9 - 1 = 8 DDR3 clock cycles and 14ns will be
9 DDR3 clock cycles.

Table 3-4. See the register section for the SDTIM* register where the field exists
Register DDR3 SDRAM Formula
Field Datasheet Datasheet (Register Field Field
Name Parameter Name Description Value (ns) must be >=) Value (h)
T_RP tRP Precharge to Activate or Refresh 13.5 (tRP/tCK) – 1 8
command
T_RCD tRCD Activate command to Read/Write 13.5 (tRCD/tCK) – 1 8
command
T_WR tWR Write recovery time 6 (tWR/tCK) – 1 3
T_RAS tRAS Active to precharge command 36 (tRAS/tCK) – 1 17
T_RC tRC Activate to Activate command in same 49.5 (tRC/tCK) – 1 20
bank
T_RRD tRRD Activate to Activate in different bank tFAW = 30ns (tFAW/(4*tCK)) – 1 4
T_WTR tWTR Write to Read command delay 6 (tWTR/tCK) – 1 3

SPRUGV8E – November 2010 – Revised January 2015 Using the DDR3 Memory Controller 49
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM Specifications www.ti.com

Table 3-5. See the register section for the SDTIM* register where the field exists
Register DDR3 SDRAM Formula
Field Datasheet Datasheet (Register Field Field
Name Parameter Name Description Value (ns) must be >=) Value (h)
T_RTP tRTP Read to precharge command delay 6 (tRTP/tCK) – 1 3
T_CKE tCKE CKE minimum pulse width 3(tCK cycles) (tCKE) – 1 2
T_XP tXP Power-down exit to non-read command 5(tCK cycles) (tXP) – 1 4

Table 3-6. See the register section for the SDTIM* register where the field exists
Register DDR3 SDRAM Formula
Field Datasheet Datasheet (Register Field Field
Name Parameter Name Description Value (ns) must be >=) Value (h)
T_CSTA DDR controller Refer to SDTIM 34 Register — — 5
parameter
T_RFC tRFC Refresh cycle time 110 (tRFC/tCK) –1 49
T_ZQCS tZQcs ZQCS command time 64(tCK (tZQcs) –1 3F
cycles)

3.2.4 Configuring Leveling Registers

The PHY registers in the Boot configuration section should be programmed according to the instructions in
Section 2.13. Full leveling can be enabled by writing a 1 to bit 31 of the RDWR_LVL_RMP_CTRL register
and then triggered by writing a 1 to bit 31 of the RDWR_LVL_CTRL register . For forced ratio leveling,
program DDR3_CONFIG_23 and DDR3_CONFIG_24 with the effective slave ratio values for devices
other than C665x or TCI6612/13/14. For C665x and TCI6612/13/14, program DDR3_CONFIG_REG_25
through DDR3_CONFIG_REG_60 with the effective slave ratio values.

3.2.5 Configuring Read Latency

The read latency can be programmed in the DDR PHY Control 1 Register [4:0]. Read latency can be
programmed from a minimum of CAS latency +1 to CAS latency +7. The value programmed should be the
required value minus one.

50 Using the DDR3 Memory Controller SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Configuring DDR3 Memory Controller Registers to Meet DDR3 SDRAM Specifications

SPRUGV8E – November 2010 – Revised January 2015 Using the DDR3 Memory Controller 51
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 Chapter 4
SPRUGV8E – November 2010 – Revised January 2015

DDR3 Memory Controller Registers

Table 4-1 lists the memory-mapped registers for the DDR3 memory controller. For the memory address of
these registers, see the device-specific data manual.

Table 4-1. DDR3 Memory Controller Registers (See datasheet memory map for base address)
Offset Acronym Register Description Section
000h MIDR Module ID and Revision Register Section 4.1
004h STATUS DDR3 Memory Controller Status Register Section 4.2
008h SDCFG SDRAM Configuration Register Section 4.3
010h SDRFC SDRAM Refresh Control Register Section 4.4
018h SDTIM1 SDRAM Timing 1 Register Section 4.5
020h SDTIM2 SDRAM Timing 2 Register Section 4.6
028h SDTIM3 SDRAM Timing 3 Register Section 4.7
038h PMCTL Power Management Control Register Section 4.8
0x54h LAT_CONFIG VBUSM Configuration Register Section 4.9
0x80 PERF_CNT_1 Performance Counter 1 Register Section 4.10
0x84 PERF_CNT_2 Performance Counter 2 Register Section 4.11
0x88 PERF_CNT_CFG Performance Counter Config Register Section 4.12
0x8C PERF_CNT_SEL Performance Counter Master Region Select Register Section 4.13
0x90 PERF_CNT_TIM Performance Counter Time Register Section 4.14
0A4h IRQSTATUS_RAW_SYS Interrupt Raw Status Register Section 4.15
0ACh IRQ_STATUS_SYS Interrupt Status Register Section 4.16
0B4h IRQENABLE_SET_SYS Interrupt Enable Set Register Section 4.17
0BCh IRQENABLE_CLR_SYS Interrupt Enable Clear Register Section 4.18
0C8h ZQCONFIG SDRAM Output Impedance Calibration Configuration Register Section 4.19
0D4h RDWR_LVL_RMP_WIN Read-Write Leveling Ramp Window Register Section 4.20
0D8h RDWR_LVL_RMP_CTRL Read-Write Leveling Ramp Control Register Section 4.21
0DCh RDWR_LVL_CTRL Read-Write Leveling Control Register Section 4.22
0E4h DDR_PHY_CTRL_1 DDR PHY Control 1 Register Section 4.23
100h PRI_COS_MAP Priority To Class-Of-Service Mapping Register Section 4.24
104h MSTID_COS_1_MAP Master ID to Class-Of-Service 1 Mapping Register Section 4.25
108h MSTID_COS_2_MAP Master ID to Class-Of-Service 2 Mapping Register Section 4.26
110h ECCCTL ECC Control Register Section 4.27
114h ECCADDR1 ECC Address Range 1 Register Section 4.28
118h ECCADDR2 ECC Address Range 2 Register Section 4.29
120h RWTHRESH Read Write Execution Threshold Register Section 4.30

52 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com

Table 4-2. DDR3 PHY Leveling Registers (See device datasheet for base address)
Offset Acronym Register Description Section
404h DDR3_CONFIG_0 DDR3 Configuration 0 Register Section 4.31
408h DDR3_CONFIG_1 DDR3 Configuration 1 Register Section 4.32
40Ch DDR3_CONFIG_2 DDR3 Configuration 2 Register Section 4.33
410h DDR3_CONFIG_3 DDR3 Configuration 3 Register Section 4.34
414h DDR3_CONFIG_4 DDR3 Configuration 4 Register Section 4.35
418h DDR3_CONFIG_5 DDR3 Configuration 5 Register Section 4.36
41Ch DDR3_CONFIG_6 DDR3 Configuration 6 Register Section 4.37
420h DDR3_CONFIG_7 DDR3 Configuration 7 Register Section 4.38
424h DDR3_CONFIG_8 DDR3 Configuration 8 Register Section 4.39
428h DDR3_CONFIG_9 DDR3 Configuration 9 Register Section 4.40
42Ch DDR3_CONFIG_10 DDR3 Configuration 10 Register Section 4.41
434h DDR3_CONFIG_12 DDR3 Configuration 12 Register Section 4.42
43Ch DDR3_CONFIG_14 DDR3 Configuration 14 Register Section 4.43
440h DDR3_CONFIG_15 DDR3 Configuration 15 Register Section 4.44
444h DDR3_CONFIG_16 DDR3 Configuration 16 Register Section 4.45
448h DDR3_CONFIG_17 DDR3 Configuration 17 Register Section 4.46
44Ch DDR3_CONFIG_18 DDR3 Configuration 18 Register Section 4.47
450h DDR3_CONFIG_19 DDR3 Configuration 19 Register Section 4.48
454h DDR3_CONFIG_20 DDR3 Configuration 20 Register Section 4.49
458h DDR3_CONFIG_21 DDR3 Configuration 21 Register Section 4.50
45Ch DDR3_CONFIG_22 DDR3 Configuration 22 Register Section 4.51
460h DDR3_CONFIG_23 (NA for TCI6612/13/14 and C665x DDR3 Configuration 23 Register Section 4.52
devices)
464h DDR3_CONFIG_24 (NA for TCI6612/13/14 and C665x DDR3 Configuration 24 Register Section 4.53
devices)
The following registers are applicable only for C665x and TCI6612/13/14 (Reserved for all other devices). Registers that say
‘TCI6612/13/14 only’ do not apply to C665x devices.
468h DDR3_CONFIG_REG_25 DDR3 Configuration 25 Register Section 4.54
46Ch DDR3_CONFIG_REG_26 DDR3 Configuration 26 Register Section 4.55
470h DDR3_CONFIG_REG_27 DDR3 Configuration 27 Register Section 4.56
474h DDR3_CONFIG_REG_28 DDR3 Configuration 28 Register Section 4.57
478h DDR3_CONFIG_REG_29 (TCI6612/13/14 only) DDR3 Configuration 29 Register Section 4.58
47Ch DDR3_CONFIG_REG_30 (TCI6612/13/14 only) DDR3 Configuration 30 Register Section 4.59
480h DDR3_CONFIG_REG_31 (TCI6612/13/14 only) DDR3 Configuration 31 Register Section 4.60
484h DDR3_CONFIG_REG_32 (TCI6612/13/14 only) DDR3 Configuration 32 Register Section 4.61
488h DDR3_CONFIG_REG_33 DDR3 Configuration 33 Register Section 4.62
48Ch DDR3_CONFIG_REG_34 DDR3 Configuration 34 Register Section 4.63
490h DDR3_CONFIG_REG_35 DDR3 Configuration 35 Register Section 4.64
494h DDR3_CONFIG_REG_36 DDR3 Configuration 36 Register Section 4.65
498h DDR3_CONFIG_REG_37 DDR3 Configuration 37 Register Section 4.66
49Ch DDR3_CONFIG_REG_38 (TCI6612/13/14 only) DDR3 Configuration 38 Register Section 4.67
4A0h DDR3_CONFIG_REG_39 (TCI6612/13/14 only) DDR3 Configuration 39 Register Section 4.68
4A4h DDR3_CONFIG_REG_40 (TCI6612/13/14 only) DDR3 Configuration 40 Register Section 4.69
4A8h DDR3_CONFIG_REG_41 (TCI6612/13/14 only) DDR3 Configuration 41 Register Section 4.70
4ACh DDR3_CONFIG_REG_42 DDR3 Configuration 42 Register Section 4.71
4B0h DDR3_CONFIG_REG_43 DDR3 Configuration 43 Register Section 4.72
4B4h DDR3_CONFIG_REG_44 DDR3 Configuration 44 Register Section 4.73
4B8h DDR3_CONFIG_REG_45 DDR3 Configuration 45 Register Section 4.74
4BCh DDR3_CONFIG_REG_46 DDR3 Configuration 46 Register Section 4.75

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 53
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 www.ti.com

Table 4-2. DDR3 PHY Leveling Registers (See device datasheet for base address) (continued)
Offset Acronym Register Description Section
4C0h DDR3_CONFIG_REG_47 (TCI6612/13/14 only) DDR3 Configuration 47 Register Section 4.76
4C4h DDR3_CONFIG_REG_48 (TCI6612/13/14 only) DDR3 Configuration 48 Register Section 4.77
4C8h DDR3_CONFIG_REG_49 (TCI6612/13/14 only) DDR3 Configuration 49 Register Section 4.78
4CCh DDR3_CONFIG_REG_50 (TCI6612/13/14 only) DDR3 Configuration 50 Register Section 4.79
4D0h DDR3_CONFIG_REG_51 DDR3 Configuration 51 Register Section 4.80
4D4h DDR3_CONFIG_REG_52 DDR3 Configuration 52 Register Section 4.81
4D8h DDR3_CONFIG_REG_53 DDR3 Configuration 53 Register Section 4.82
4DCh DDR3_CONFIG_REG_54 DDR3 Configuration 54 Register Section 4.83
4E0h DDR3_CONFIG_REG_55 DDR3 Configuration 55 Register Section 4.84
4E4h DDR3_CONFIG_REG_56 (TCI6612/13/14 only) DDR3 Configuration 56 Register Section 4.85
4E8h DDR3_CONFIG_REG_57 (TCI6612/13/14 only) DDR3 Configuration 57 Register Section 4.86
4ECh DDR3_CONFIG_REG_58 (TCI6612/13/14 only) DDR3 Configuration 58 Register Section 4.87
4F0h DDR3_CONFIG_REG_59 (TCI6612/13/14 only) DDR3 Configuration 59 Register Section 4.88
4F4h DDR3_CONFIG_REG_60 DDR3 Configuration 60 Register Section 4.89

54 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Module ID and Revision Register (MIDR)

4.1 Module ID and Revision Register (MIDR)

The Module ID and Revision register contains the revision number and identification data of the DDR3
peripheral, and is described in the following figure and table.

Figure 4-1. Module ID and Revision Register (MIDR)

31 28 27 16 15 8 7 6 5 0
Reserved MOD_ID MJ_REV Reserved MIN_REV
R=0x4 R=0x46 R=0x4 R=0x0 R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-3. Module ID and Revision Register (MIDR) Field Descriptions

Bit Field Attribute Description
31-28 Reserved R Value = 0x4
Reserved. The reserved bit location is always read as 0. A value written to this field has
no effect.
27-16 MOD_ID R Value = 0x46
Module ID Bits
15-8 MJ_REV R Value = 0x4
Major Revision
7-6 Reserved R Value = 0x0
Reserved. The reserved bit location is always read as 0. A value written to this field has
no effect.
5-0 MIN_REV R Value = 0x0
Minor Revision

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 55
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Memory Controller Status Register (STATUS) www.ti.com

4.2 DDR3 Memory Controller Status Register (STATUS)

This register contains the status of the DDR3 module and is described in the following figure and table.

Figure 4-2. DDR3 Memory Controller Status Register (STATUS)

31 30 7 6 5 4 3 2 1 0
BE Reserved RDLVGATETO RDLVLTO WRLVLTO Reserved IFRDY Reserved
R=0 R=0 R=0 R=0 R=0 R=0 R=0 R=0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-4. DDR3 Memory Controller Status Register (STATUS) Field Descriptions
Bit Field Attribute Description
31 BE R Big Endian. Reflects the value on the BIG_ENDIAN port that defines whether the EMIF is in big or
little-endian mode
30 Reserved R Value = 0
This field is tied off to 0x1.
29-7 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.
6 RDLVGATETO R Read DQS Gate Training Timeout
• 0 = Reset value
• 1 = Indicates read DQS gate training has timed out
5 RDLVLTO R Read Data Eye Training Timeout
• 0 = Reset value
• 1 = Read data eye training has timed out
4 WRLVLTO R Write Leveling Timeout
• 0 = Reset value
• 1 = Write Leveling has timed out
3 Reserved R Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.
2 IFRDY R DDR3 memory controller interface logic ready bit. The interface logic controls the signals used to
communicate with DDR3 SDRAM devices. This bit displays the status of the interface logic.
• 0 = Interface logic is not ready; either powered down, not ready, or not locked.
• 1 = Interface logic is powered up, locked and ready for operation.
1-0 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.

56 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com SDRAM Configuration Register (SDCFG)

4.3 SDRAM Configuration Register (SDCFG)

The SDRAM Configuration Register (SDCFG) contains field that program the DDR3 memory controller to
meet the specifications of the DDR3 memory. These fields configure the DDR3 memory controller to
match the data bus width, CAS latency, number of internal banks, and page size of the external DDR3
memory. For more information on initializing the configuration registers of the DDR3 memory controller,
see Section 3.2.

Figure 4-3. SDRAM Configuration Register (SDCFG)

31 29 28 27 26 24 23 22 21 20 19 18
SDRAM_TYPE IBANK_POS DDR_TERM Reserved DYN_ODT DDR_DISABLE_DLL SDRAM
_DRIVE
RW=0x0 RW=0x0 RW=0x0 R=0x0 RW=0x0 RW=0x0 RW=0x0
17 16 15 14 13 10 9 7 6 4 3 2 0
CWL NM CL ROWSIZE IBANK EBANK PAGESIZE
RW=0x0 RW=0x0 RW=0x2 RW=0x0 RW=0x0 RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-5. SDRAM Configuration Register (SDCFG) Field Descriptions

Bit Field Attribute Description
31-29 SDRAM_TYPE RW Value = 3
SDRAM type selection. Set to 3 for DDR3. All other values reserved.
28-27 IBANK_POS RW Internal bank position.
• 0 = Assigns internal bank address bits from address as shown in Table 2-5
• 1,2,3 = Assign internal bank address bits from address as shown in Table 2-6
26-24 DDR_TERM RW Defines termination resistor value.
• 0 = Disables termination
• 1 = RZQ/4
• 2 = RZQ/2
• 3 = RZQ/6
• 4 = RZQ/12
• 5 = RZQ/8
23 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has
no effect.
22-21 DYN_ODT RW Dynamic On-Die Termination
• 0 = Turn off dynamic ODT.
• 1 = RZQ/4
• 2 = RZQ/2
All other values reserved.
20 DDR_DISABLE_DLL RW Disable DLL select.
• 0 = Normal Operation.
• 1 = Disables DLL inside SDRAM.
19-18 SDRAM_DRIVE RW SDRAM drive strength.
• 0 = RZQ/6
• 1 = RZQ/7
All other values reserved.
17-16 CWL RW CAS Write Latency. Lower value gives better performance.
• 0 = CAS write latency of 5
• 1 = CAS write latency of 6
• 2 = CAS write latency of 7
• 3 = CAS write latency of 8

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 57
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
SDRAM Configuration Register (SDCFG) www.ti.com

Table 4-5. SDRAM Configuration Register (SDCFG) Field Descriptions (continued)

Bit Field Attribute Description
15-14 NM RW DDR3 data bus width. A write to this bit field will cause the memory controller to start
SDRAM initialization sequence.
• 0 = 64-bit bus width.
• 1 = 32-bit bus width.
• 2 = 16-bit bus width.
All other values reserved.
13-10 CL RW CAS Latency. The value of this field defines the CAS latency, to be used when
accessing connected SDRAM devices. A write to this field will cause the DDR3 memory
controller to start the SDRAM initialization sequence.
• 2 = CAS latency of 5.
• 4 = CAS latency of 6.
• 6 = CAS latency of 7.
• 8 = CAS latency of 8.
• 10 = CAS latency of 9.
• 12 = CAS latency of 10.
• 14 = CAS latency of 11.
All other values are reserved.
9-7 ROWSIZE RW Row size. Defines the number of row address bits of connected SDRAM devices
• 0 = 9 row bits.
• 1 = 10 row bits.
• 2 = 11 row bits.
• 3 = 12 row bits.
• 4 = 13 row bits.
• 5 = 14 row bits.
• 6 = 15 row bits.
• 7 = 16 row bits.
6- 4 IBANK RW Internal SDRAM bank setup bits. Defines number of banks inside connected SDRAM
devices. A write to this bit will cause the DDR3 memory controller to start SDRAM
initialization sequence. Values 4-7 are reserved for this field. A word is equal to the bus
width of the individual SDRAM devices used (example, 1 byte for x8 and 2bytes for x16
devices)
• 0 = One bank SDRAM devices.
• 1 = Two bank SDRAM devices.
• 2 = Four bank SDRAM devices.
• 3 = Eight bank SDRAM devices.
3 EBANK RW External chip select setup. Defines whether SDRAM accesses use 1 or 2 chip select
lines as follows:
• 0 = Use DCE0# for all SDRAM accesses.
• 1 = Use DEC0# and DCE1# for SDRAM accesses.
2 -0 PAGESIZE RW Page size bits. Defines internal page size of the external DDR3 memory. A write to this
bit will cause the DDR3 memory controller to start the SDRAM initialization sequence.
Values 4-7 are reserved for this field. A word is equal to the bus width of the individual
SDRAM devices used (example, 1 byte for x8 and 2bytes for x16 devices)
• 0 = 256-word page requiring 8 column address bits.
• 1 = 512-word page requiring 9 column address bits.
• 2 = 1024-word page requiring 10 column address bits.
• 3 = 2048-word page requiring 11 column address bits.

58 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com SDRAM Refresh Control Register (SDRFC)

4.4 SDRAM Refresh Control Register (SDRFC)

The SDRAM Refresh Control Register (SDRFC) is used to configure the DDR3 memory controller to:
• Enter and Exit the self-refresh state.
• Meet the refresh requirements of the attached DDR3 device by programming a rate at which the DDR3
memory controller issues autorefresh commands.
The SDRFC register is described in the following figure and table.

Figure 4-4. SDRAM Refresh Control Register (SDRFC)

31 30 29 28 27 26 24 23 16 15 0
INITREF_DIS Reserved SRT ASR Reserved PASR Reserved REFRESH
_RATE
RW=0x1 R=0x0 RW=0x0 RW=0x0 R=0x0 RW=0x0 R=0x0 RW=0x61A8
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-6. SDRAM Refresh Control (SDRFC) Register Field Descriptions

Bit Field Attribute Description
31 INITREF_DIS RW Initialization and Refresh Disable.
• 0 = Normal operation
• 1 = Disables SDRAM initialization and refreshes, but carries out SDRAM write/read
transactions
30 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no
effect.
29 SRT RW DDR3 self-refresh temperature range. A write to this bit will cause the DDR3 memory controller
to start SDRAM initialization sequence.
• 0 = Normal operating temperature range. This must be set to zero if ASR bit is set to 1.
• 1 = Extended operating temperature range when ASR bit is set to zero.
28 ASR RW A write to this bit will cause the DDR3 memory controller to start SDRAM initialization sequence.
• 0 = Use manual self-refresh
• 1 = Auto self-refresh enable
27 Reserved R Reserved. The reserved bit location is always read as 0. A value written to this field has no effect
26-24 PASR RW Partial Array self-refresh. These bits get loaded into the extended mode register during
initialization. A write to this bit will cause the DDR3 memory controller to start SDRAM
initialization sequence.
• 0 = Full-array.
• 1 or 5 = ½ array.
• 2 or 6 = ¼ array.
• 3 or 7 = 1/8 array.
• 4 = ¾ array.
23-16 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect
15-0 REFRESH_RATE RW The value in this field is used to define the rate at which connected SDRAM devices will be
refreshed.
REFRESH_RATE = Refresh period * DDR3 clock frequency.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 59
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
SDRAM Timing 1 (SDTIM1) Register www.ti.com

4.5 SDRAM Timing 1 (SDTIM1) Register

SDRAM Timing 1 register (SDTIM1) configures the DDR3 memory controller to meet many of the AC
timing specifications of the DDR3 memory. Note that DDR3CLKOUT is equal to the period of the
DDR3CLKOUT signal. See the DDR3 memory datasheet for information on appropriate values to program
each field. The SDTIM1 register is described in the following figure and table.

Figure 4-5. SDRAM Timing 1 (SDTIM1) Register

31 29 28 25 24 21 20 17 16 12 11 6 5 3 2 0
Reserved T_RP T_RCD T_WR T_RAS T_RC T_RRD T_WTR
R=0x0 RW=0xA RW=0xA RW=0xB RW=0x1B RW=0x26 RW=0x5 RW=0x4
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-7. SDRAM Timing 1 (SDTIM1) Register Field Descriptions

Bit Field Attribute Description
31- 29 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect
28-25 T_RP RW These bits specify the minimum number of DDR3CLKOUT cycles from a precharge command to a refresh
or activate command, minus 1. The value of this parameter can be derived from the t RP AC timing
parameter in the DDR3 memory data sheet. Calculate using the formula:
T_RP = (t RP/t CK) – 1
24-21 T_RCD RW These bits specify the minimum number of DDR3CLKOUT cycles from an activate command to a read or
write command, minus 1. The value of this parameter can be derived from the t RCD AC timing parameter
in the DDR3 memory data sheet. Calculate using the formula:
T_RCD = (t RCD/t CK) – 1
20-17 T_WR RW These bits specify the minimum number of DDR3CLKOUT cycles from the last write transfer to a
precharge command, minus 1. The value of this parameter can be derived from the t WR AC timing
parameter in the DDR3 memory data sheet. Calculate using the formula:
T_WR = (t WR/t CK) – 1
16-12 T_RAS RW These bits specify the minimum number of DDR3CLKOUT cycles from an activate command to
precharge command, minus 1. The value of this parameter can be derived from the minimum value of the
t RAS AC timing parameter in the DDR3 memory data sheet. Calculate using the formula:
T_RAS = (t RAS/t CK) – 1
11-6 T_RC RW These bits specify the minimum number of DDR3CLKOUT cycles from an activate command to an
activate command, minus 1. The value of this parameter can be derived from the t RCAC timing parameter
in the DDR3 memory data sheet. Calculate using the formula:
T_RC = (t RC/t CK) – 1
5-3 T_RRD RW These bits specify the minimum number of DDR3CLKOUT cycles from an activate to an activate in a
different bank, minus 1. The value of this parameter can be derived from the t FAW AC timing parameter in
the DDR3 memory data sheet. Calculate using the formula:
T_RRD = (t FAW/(4*t CK)) – 1
2-0 T_WTR RW These bits specify the minimum number of DDR3CLKOUT cycles from the last write to a read command,
minus 1. The value of this parameter can be derived from the t WTR AC timing parameter in the DDR3
memory data sheet. Convert the t WTR value from the memory datasheet into ns before using the formula
below. Calculate using the formula:
T_WTR = (t WTR/t CK) – 1

60 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com SDRAM Timing 2 (SDTIM2) Register

4.6 SDRAM Timing 2 (SDTIM2) Register

Like the SDRAM Timing 1 register (SDTIM1), the SDRAM Timing 2 register (SDTIM2) also configures the
DDR3 memory controller to meet many of the AC timing specifications of the DDR3 memory. See the
DDR3 memory datasheet for information on appropriate values to program each field. The SDTIM2
register is described in the following figure and table.

Figure 4-6. SDRAM Timing 2 (SDTIM2) Register

31 30 28 27 25 24 16 15 6 5 3 2 0
Reserved T_XP Reserved T_XSNR T_XSRD T_RTP T_CKE
R=0x0 RW=0x6 R=0x7 RW=0x5F RW=0x1FF RW=0x5 RW=0x5
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-8. SDRAM Timing 2 (SDTIM2) Register Field Descriptions

Bit Field Attribute Description
31 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect
30-28 T_XP RW These bits specify the minimum number of DDR3CLKOUT cycles from Power down exit to any
command other than a read command, minus 1. The value of this parameter can be derived from
the t XP AC timing parameter in the DDR3 memory data sheet. Convert the t XP datasheet
parameter value into ns before using formula below.
Calculate using the formula:
T_XP = (t XP/t CK) – 1
27-25 Reserved R Reserved. A value written to this field has no effect.
24-16 T_XSNR RW These bits specify the minimum number of DDR3CLKOUT cycles from a self-refresh exit to a
command that does not require a locked DLL, minus 1. The value of this parameter can be
derived from the t XS AC timing parameter in the DDR3 memory data sheet. Calculate using the
formula:
T_XSNR = (t XS /t CK)– 1
15-6 T_XSRD RW These bits specify the minimum number of DDR3CLKOUT cycles from a self-refresh exit to a
command that requires a locked DLL, minus 1. The value of this parameter can be derived from
the t XSDLL AC timing parameter in the DDR3 memory data sheet. This parameter typically
appears in the datasheet in terms of t CK clock cycles.
Calculate using the formula:
T_XSRD = t XSDLL– 1
5-3 T_RTP RW These bits specify the minimum number of DDR3CLKOUT cycles from the last read to precharge
command, minus 1. The value of this parameter can be derived from the t RTP AC timing
parameter in the DDR3 memory data sheet. Convert the t XP datasheet parameter value into ns
before using formula below. Calculate using the formula:
T_RTP = (t RTP/t CK) – 1
2-0 T_CKE RW These bits specify the minimum number of DDR3CLKOUT cycles between transitions on the
DSDCKE pin, minus 1. The value of this parameter can be derived from the t CKE AC timing
parameter in the DDR3 memory data sheet.
Calculate using the formula:
T_CKE = (tCKE/tCK) – 1

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 61
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
SDRAM Timing 3 (SDTIM3) Register www.ti.com

4.7 SDRAM Timing 3 (SDTIM3) Register

Like the SDRAM Timing 1 and 2 registers (SDTIM1 & SDTIM2), the SDRAM Timing 3 register (SDTIM3)
also configures the DDR3 memory controller to meet many of the AC timing specifications of the DDR3
memory. See the DDR3 memory datasheet for information on appropriate values to program each field.
The SDTIM3 register is described in the following figure and table.

Figure 4-7. SDRAM Timing 3 (SDTIM3) Register

31 28 27 24 23 21 20 15 14 13 12 4 3 0
T_PDLL_UL T_CSTA T_CKESR ZQ_ZQCS Reserved T_RFC T_RAS_MAX
RW=0x0 RW=0x0 RW=0x3 RW=0x3F R=0x3 RW=0x57 RW=0x6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-9. SDRAM Timing 3 (SDTIM3) Register Field Descriptions

Bit Field Attribute Description
31-28 T_PDLL_UL RW Value = 0
This field must always be programmed to 0x5.
27-24 T_CSTA RW Minimum DDR3CLKOUT cycles between write-to-write or read-to-read data phases to different
chip selects, minus 1.
This field should be set according to PHY requirements as 0x5.
23-21 T_CKESR RW Value = 0
Minimum DDR3CLKOUT cycles for which DDR3 should remain in self-refresh. This parameter
typically appears as number of t CK clock cycles.
T_CKESR = (tCKESR/tCK) – 1
20-15 ZQ_ZQCS RW These bits specify the minimum number of DDR3CLKOUT cycles for a ZQCS command, minus
1. The value of this parameter can be derived from the t ZQCS AC timing parameter in the DDR3
memory data sheet. This parameter typically appears as number of t CK clock cycles. Calculate
using the formula
ZQ_ZQCS = t ZQCS – 1
14-13 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no
effect.
12-4 T_RFC RW These bits specify the minimum number of DDR3CLKOUT cycles from a refresh or load mode
command to a refresh or activate command, minus 1. The value of this parameter can be
derived from the t RFC AC timing parameter in the DDR3 memory data sheet. Calculate using
the formula
T_RFC = (t RFC/t CK) – 1
3-0 T_RAS_MAX RW This field must always be programmed to 0xF.

62 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Power Management Control Register (PMCTL)

4.8 Power Management Control Register (PMCTL)

The PMCTL register is described in the following figure and table.

Figure 4-8. Power Management Control Register (PMCTL)

31 16 15 12 11 10 8 7 4 3 0
Reserved PD_TIM Reserved LP_MODE SR_TIM Reserved
R=0x0 RW=0x0 R=0x0 RW=0x0 RW=0x0 R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-10. Power Management Control Register (PMCTL) Field Descriptions

Bit Field Attribute Description
31-16 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect
15-12 PD_TIM RW Power Management timer for power-down. The DDR3 memory controller will put the SDRAM in
power-down mode after the DDR3 controller is idle for PD_TIM number of DDR3CLKOUT cycles and
if LP_MODE is set to 4.
• 0 = Immediately enter power-down
• 1 = Enter power-down after 16 clocks
• 2 = Enter power-down after 32 clocks
• 3 = Enter power-down after 64 clocks
• 4 = Enter power-down after 128 clocks
• 5 = Enter power-down after 256 clocks
• 6 = Enter power-down after 512 clocks
• 7 = Enter power-down after 1024 clocks
• 8 = Enter power-down after 2048 clocks
• 9 = Enter power-down after 4096 clocks
• 10 = Enter power-down after 8912 clocks
• 11 = Enter power-down after 16384 clocks
• 12 = Enter power-down after 32768 clocks
• 13 = Enter power-down after 65536 clocks
• 14 = Enter power-down after 131072 clocks
• 15 = Enter power-down after 262144 clocks
11 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect
10-8 LP_MODE RW Automatic power management enable.
• 2 = Self-refresh mode
• 4 = Power-down mode
All other values will disable automatic power management.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 63
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Power Management Control Register (PMCTL) www.ti.com

Table 4-10. Power Management Control Register (PMCTL) Field Descriptions (continued)
Bit Field Attribute Description
7-4 SR_TIM RW Power management timer for self-refresh. The DDR3 memory controller will put the external SDRAM
in self-refresh mode after DDR3 controller has been idle for these number of DDR3CLKOUT cycles
and LP_MODE is set to 2.
• 0 = Immediately enter self-refresh
• 1 = Enter self-refresh after 16 clocks
• 2 = Enter self-refresh after 32 clocks
• 3 = Enter self-refresh after 64 clocks
• 4 = Enter self-refresh after 128 clocks
• 5 = Enter self-refresh after 256 clocks
• 6 = Enter self-refresh after 512 clocks
• 7 = Enter self-refresh after 1024 clocks
• 8 = Enter self-refresh after 2048 clocks
• 9 = Enter self-refresh after 4096 clocks
• 10 = Enter self-refresh after 8912 clocks
• 11 = Enter self-refresh after 16384 clocks
• 12 = Enter self-refresh after 32768 clocks
• 13 = Enter self-refresh after 65536 clocks
• 14 = Enter self-refresh after 131072 clocks
• 15 = Enter self-refresh after 262144 clocks
3-0 Reserved R Reserved

64 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com VBUSM Configuration Register (VBUSM_CONFIG)

4.9 VBUSM Configuration Register (VBUSM_CONFIG)

The VBUSM_CONFIG register is described in the following figure and table.

Figure 4-9. VBUSM Configuration Register (VBUSM_CONFIG)

31 24 23 16 15 8 7 0
Reserved COS_COUNT_1 COS_COUNT_2 PR_OLD_COUNT
R=0x0 RW=0xFF RW=0xFF RW=0xFF
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-11. VBUSM Configuration Register (VBUSM_CONFIG) Field Descriptions

Bit Field Attribute Description
31-24 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no
effect.
23-16 COS_COUNT_1 RW Value = 0xFF
Priority raise counter for Class of Service 1. Number of DDR3CLKOUT cycles after which
the DDR3 controller momentarily raises the priority of Class of Service 1 commands in
Command FIFO.
Number of clock cycles = COS_COUNT_1 x 16 clocks
15-8 COS_COUNT_2 RW Value = 0xFF
Priority raise counter for Class of Service 2. Number of DDR3CLKOUT cycles after which
the DDR3 controller momentarily raises the priority of Class of Service 2 commands in
Command FIFO.
Number of clock cycles = COS_COUNT_2 x 16 clocks
7-0 PR_OLD_COUNT RW Value = 0xFF
Priority raise old counter. Number of DDR3CLKOUT cycles after which DDR3 controller
momentarily raises the priority of the oldest command in Command FIFO.
Number of clock cycles = PR_OLD_COUNT_2 x 16 clocks

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 65
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Performance Counter 1 Register (PERF_CNT_1) www.ti.com

4.10 Performance Counter 1 Register (PERF_CNT_1)

The PERF_CNT_1 register is described in the following figure and table.

Figure 4-10. Performance Counter 1 Register (PERF_CNT_1)

31 0
COUNTER_1
R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-12. Performance Counter 1 Register (PERF_CNT_1) Field Descriptions

Bit Field Attribute Description
31-0 COUNTER_1 R 32-bit counter can be programmed as specified in the Performance Counter Config and
Performance Counter Master Region Select registers.

66 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Performance Counter 2 Register (PERF_CNT_2)

4.11 Performance Counter 2 Register (PERF_CNT_2)

The PERF_CNT_2 register is described in the following figure and table.

Figure 4-11. Performance Counter 2 Register (PERF_CNT_2)

31 0
COUNTER_2
R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-13. Performance Counter 2 Register (PERF_CNT_2) Field Descriptions

Bit Field Attribute Description
31-0 COUNTER_2 R 32-bit counter can be programmed as specified in the Performance Counter Config and
Performance Counter Master Region Select registers.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 67
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Performance Counter Config Register (PERF_CNT_CFG) www.ti.com

4.12 Performance Counter Config Register (PERF_CNT_CFG)

The PERF_CNT_CFG register is described in the following figure and table.

Figure 4-12. Performance Counter Config Register (PERF_CNT_CFG)

31 30 29 20 19 16
CNTR2_MSTID_EN CNTR2_REGION_EN Reserved CNTR2_CFG
RW=0x0 RW=0x0 R=0x0 RW=0x1
15 14 13 4 3 0
CNTR1_MSTID_EN CNTR1_REGION_EN Reserved CNTR1_CFG
RW=0x0 RW=0x0 R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-14. Performance Counter Config Register (PERF_CNT_CFG) Field Descriptions

Bit Field Attribute Description
31 CNTR2_MSTID_EN RW Master ID filter enable for Performance Counter 2 Register. Set to 1 to enable filtering of
events for counter 2 by Master ID. Refer to your device data manual for the master IDs of
various masters.
30 CNTR2_REGION_EN RW Memory space region enable for Performance Counter 2 Register. Set to 1 to enable
filtering of events for counter 2 by the accessed memory region.
29-20 Reserved R Value = 0x0
Reserved
19-16 CNTR2_CFG RW Filter configuration selected for Performance Counter 2. This field selects the type of
event to count for Counter 2. Refer to Table 2-17 for various configuration options.
15 CNTR1_MSTID_EN RW Master ID filter enable for Performance Counter 1 Register. Set to 1 to enable filtering of
events for counter 1 by Master ID. Refer to your device data manual for the master IDs of
various masters.
14 CNTR1_REGION_EN RW Memory space region enable for Performance Counter 1 Register. Set to 1 to enable
filtering of events for counter 1 by the accessed memory region.
13-4 Reserved R Value = 0x0
Reserved
3-0 CNTR1_CFG RW Filter configuration selected for Performance Counter 1. This field selects the type of
event to count for Counter 1. Refer to Table 2-17 for various configuration options.

68 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Performance Counter Master Region Select Register (PERF_CNT_SEL)

4.13 Performance Counter Master Region Select Register (PERF_CNT_SEL)

For events that can be configured to enable master ID and/or memory region filters, the value of the
master ID and the region select options for the counters are programmed in the PERF_CNT_SEL register.
The PERF_CNT_SEL register is described in the following figure and table.

Figure 4-13. Performance Counter Master Region Select Register (PERF_CNT_SEL)

31 24 23 20 19 16 15 8 7 4 3 0
MSTID2 Reserved REGION_SEL2 MSTID1 Reserved REGION_SEL1
RW=0x0 R=0x0 RW=0x0 RW=0x0 R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-15. Performance Counter Master Region Select Register (PERF_CNT_SEL) Field
Descriptions
Bit Field Attribute Description
31-24 MSTID2 RW Master ID for Performance Counter 2 Register. Refer to your device data manual for the master
IDs of various masters.
23-20 Reserved R Value = 0x0
Reserved
19-16 REGION_SEL2 RW Region select for Performance Counter 2.
• 0x0 - DDR3 memory space
• 0x7 - DDR3 controller memory mapped registers
All other values are reserved.
15-8 MSTID1 RW Master ID for Performance Counter 1 Register. Refer to your device data manual for the master
IDs of various masters.
7-4 Reserved R Value = 0x0
Reserved
3-0 REGION_SEL1 RW Region select for Performance Counter 1.
• 0x0 - DDR3 memory space
• 0x7 - DDR3 controller memory mapped registers
All other values are reserved.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 69
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Performance Counter Time Register (PERF_CNT_TIM) www.ti.com

4.14 Performance Counter Time Register (PERF_CNT_TIM)

The PERF_CNT_TIM register is described in the following figure and table.

Figure 4-14. Performance Counter Time Register (PERF_CNT_TIM)

31 0
TOTAL_TIME
R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-16. Performance Counter Time Register (PERF_CNT_TIM) Field Descriptions

Bit Field Attribute Description
31-0 TOTAL_TIME R 32-bit counter continuously counts number of DDR/2 clock cycles elapsed after the controller
is brought out of reset.

70 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Interrupt Raw Status Register (IRQSTATUS_RAW_SYS)

4.15 Interrupt Raw Status Register (IRQSTATUS_RAW_SYS)

The IRQSTATUS_RAW_SYS register is described in the following figure and table.

Figure 4-15. Interrupt Raw Status Register (IRQSTATUS_RAW_SYS)

31 5 4 3 2 1 0
Reserved RD_ECC_ERR_SYS WR_ECC_ERR_SYS Reserved ERR_SYS
R=0x0 WOS=0x0 WOS=0x0 R=0x0 WOS=0x0
Legend: R = Read only; WOS = Write one to set; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-17. Interrupt Raw Status Register (IRQSTATUS_RAW_SYS) Field Descriptions

Bit Field Attribute Description
31- 5 Reserved R Value = 0x0
Reserved
4 RD_ECC_ERR_SYS WOS Value = 0x0
Raw status of read ECC error interrupt. Writing a 1 sets the raw status. Writing a 0 has no
effect.
3 WR_ECC_ERR_SYS WOS Value = 0x0
Raw status of write ECC error interrupt. Writing a 1 sets the raw status. Writing a 0 has no
effect.
2-1 Reserved R Value = 0x0
Reserved
0 ERR_SYS WOS Value = 0x0
Raw status of system VBUSM interrupt for command or address error. Writing a 1 sets the
raw status. Writing a 0 has no effect.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 71
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Interrupt Status Register (IRQSTATUS_ SYS) www.ti.com

4.16 Interrupt Status Register (IRQSTATUS_ SYS)

The IRQSTATUS_SYS register is described in the following figure and table.

Figure 4-16. Interrupt Status Register (IRQSTATUS_ SYS)

31 5 4 3 2 1 0
Reserved RD_ECC_ERR_SYS WR_ECC_ERR_SYS Reserved ERR_SYS
R WOC WOC R WOC
Legend: R = Read only; WOC = write one to clear; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-18. Interrupt Status Register (IRQSTATUS_SYS) Field Descriptions

Bit Field Attribute Description
31- 5 Reserved R Value = 0x0
Reserved.
4 RD_ECC_ERR_SYS WOC Value = 0x0
Enabled status of read ECC error interrupt. Writing a 1 clears the status as well the raw
status. Writing a 0 has no effect.
3 WR_ECC_ERR_SYS WOC Value = 0x0
Enabled status of write ECC error interrupt. Writing a 1 clears the status as well the raw
status. Writing a 0 has no effect.
2-1 Reserved R Value = 0x0
Reserved.
0 ERR_SYS WOC Value = 0x0
Enabled status of system VBUSM interrupt for command or address error. Writing a 1
clears the status as well the raw status. Writing a 0 has no effect.

72 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Interrupt Enable Set Register (IRQSTATUS_ SET_SYS)

4.17 Interrupt Enable Set Register (IRQSTATUS_ SET_SYS)

The IRQSTATUS_SET_SYS register is described in the following figure and table.

Figure 4-17. Interrupt Enable Set Register (IRQSTATUS_ SET_SYS)

31 5 4 3 2 1 0
Reserved RD_ECC_ERR_SYS WR_ECC_ERR_SYS Reserved ERR_SYS
R=0x0 WOS=0x0 WOS=0x0 R=0x0 WOS=0x0
Legend: R = Read only; WOS = Write one to set; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-19. Interrupt Enable Set Register (IRQSTATUS_ SET_SYS) Field Descriptions
Bit Field Attribute Description
31- 5 Reserved R Value = 0x0
Reserved.
4 RD_ECC_ERR_SYS WOS Value = 0x0
Enabled set for read ECC error interrupt. Writing a 1 will enable the read ECC error
interrupt, set this bit as well as the bit in Interrupt Enable Clear Register. Writing a 0 has no
effect.
3 WR_ECC_ERR_SYS WOS Value = 0x0
Enabled set for write ECC error interrupt. Writing a 1 will enable the write ECC error
interrupt, set this bit as well as the bit in Interrupt Enable Clear Register. Writing a 0 has no
effect.
2-1 Reserved R Value = 0x0
Reserved.
0 ERR_SYS WOS Value = 0x0
Enable set for system VBUSM interrupt for command or address error. Writing a 1 will
enable the interrupt, and set this bit as well as the corresponding Interrupt Enable Clear
Register. Writing a 0 has no effect.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 73
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS) www.ti.com

4.18 Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS)

The IRQSTATUS_CLR_SYS register is described in the following figure and table.

Figure 4-18. Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS)

31 5 4 3 2 1 0
Reserved RD_ECC_ERR_SYS WR_ECC_ERR_SYS Reserved ERR_SYS
R WOC=0x0 WOC=0x0 R WOC=0x0
Legend: R = Read only; WOC = Write one to clear; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-20. Interrupt Enable Clear Register (IRQSTATUS_ CLR_SYS) Field Descriptions
Bit Field Attribute Description
31- 5 Reserved R Value = 0x0
Reserved.
4 RD_ECC_ERR_SYS WOC Value = 0x0
Enabled clear for read ECC error interrupt. Writing a 1 will disable the read ECC error
interrupt, clear this bit as well as the bit in Interrupt Enable Clear Register. Writing a 0
has no effect.
3 WR_ECC_ERR_SYS WOC Value = 0x0
Enabled clear for write ECC error interrupt. Writing a 1 will disable the write ECC error
interrupt, clear this bit as well as the bit in Interrupt Enable Clear Register. Writing a 0
has no effect.
2-1 Reserved R Value = 0x0
Reserved.
0 ERR_SYS WOC Value = 0x0
Enable clear for system VBUSM interrupt for command or address error. Writing a 1 will
disable the interrupt, and clear this bit as well as the corresponding Interrupt Enable Set
Register. Writing a 0 has no effect.

74 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com SDRAM Output Impedance Calibration Configuration Register (ZQCFG)

4.19 SDRAM Output Impedance Calibration Configuration Register (ZQCFG)

The ZQCFG register is described in the following figure and table.

Figure 4-19. SDRAM Output Impedance Calibration Configuration Register (ZQCFG)

31 30 29 28
ZQ_CS1EN ZQ_CS0EN ZQ_DUALCALEN ZQ_SFEXITEN
RW=0x1 RW=0x1 RW=0x0 RW=0x1
27 20 19 18 17 16 15 0
Reserved ZQ_ZQINIT_MULT ZQ_ZQCL_MULT ZQ_REFINTERVAL
R RW=0x1 RW=0x3 RW=0x4C1F
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-21. SDRAM Output Impedance Calibration Configuration Register (ZQCFG) Field
Descriptions
Bit Field Attribute Description
31 ZQ_CS1EN RW ZQ calibration for CS1
• 0 = Disable ZQ calibration for CS1
• 1 = Enable ZQ calibration for CS1
30 ZQ_CS0EN RW ZQ calibration for CS0
• 0 = Disable ZQ calibration for CS0
• 1 = Enable ZQ calibration for CS0
29 ZQ_DUALCALEN RW ZQ Dual Calibration enable. Allows both ranks to be calibrated simultaneously.
• 0 = Dual ZQ calibration disable
• 1 = Both chip selects have a separate calibration resistor per device. This bit
should always be set to 1 . See the Silicon Errata for your device for more details
on this issue.
28 ZQ_SFEXITEN RW ZQCL on Self-refresh, Active power-down and precharge power-down exit enable.
• 0 = Disable ZQCL on Self-refresh, Active power-down and precharge power-down
exit enable
• 1 = Enable ZQCL on Self-refresh, Active power-down and precharge power-down
exit enable.
Set this value to 1 to issue a ZQCL command upon self-refresh exit.
27- 20 Reserved R Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field
has no effect.
19-18 ZQ_ZQINIT_MULT RW Number of ZQCL intervals that make up a ZQINIT interval, minus one. The value of
this parameter can be derived from the t ZQinit and t ZQoper AC timing parameters in the
DDR3 memory data sheet.
Calculate using the formula T_ZQ_ZQINIT_MULT = (t ZQinit/t ZQoper – 1)
17 -16 ZQ_ZQCL_MULT RW Number of ZQCS intervals that make up a ZQCL interval, minus one. ZQCS interval is
defined by ZQ_ZQCS field in SDRAM Timing 3 (SDTIM3) register. The value of this
parameter can be derived using the formula:
T_ZQ_ZQCL_MULT = (t ZQoper/t ZQCS – 1)

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 75
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
SDRAM Output Impedance Calibration Configuration Register (ZQCFG) www.ti.com

Table 4-21. SDRAM Output Impedance Calibration Configuration Register (ZQCFG) Field Descriptions
(continued)
Bit Field Attribute Description
15-0 ZQ_REFINTERVAL RW Number of refresh periods between ZQCS commands, minus one. This field supports
between one refresh period to 256 ms between ZQCS calibration commands. Refresh
period is defined by REFRESH_RATE field in SDRAM Refresh control (SDRFC)
register.
ZQ_REFINTERVAL = number of refresh periods between ZQCS commands.
The interval is calculated as = 0.5% / [(Tsens x Tdriftrate) + (Vsens x Vdriftrate)].
Tsens = max (dRTTdT, dRONdTM) from the memory device datasheet.
Vsens = max(dRTTdV, dRONdVM) from the memory device datasheet
Tdriftrate = drift rate in o C/second. This is the temperature drift rate that the SDRAM is
subject to in the application. Vdriftrate = drift rate in mV/second. This is the voltage drift
rate that the SDRAM is subject to in the application.
Example:
If Tsens= 1.5%/ o C, Vsens = 0.15%/mV, Tdriftrate = 1.2 o C/second and Vdriftrate =
10mV/second,
Interval = 0.5/[(1.5 x 1.2) + (0.15 x 10)] = 152ms.
Since refresh interval = 7.8µs, ZQ_REFINTERVAL = 152ms/7.8µs = 0x4C1F

76 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN)

4.20 Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN)

The RDWR_LVL_RMP_WIN register is described in the figure and table below.

Figure 4-20. Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN)

31 0
Reserved
R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-22. Read-Write Leveling Ramp Window Register (RDWR_LVL_RMP_WIN) Field

Descriptions
Bit Field Attribute Description
31-0 Reserved R Value = 0x0. This register is reserved, as ramp incremental leveling is not
supported on Keystone-I devices.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 77
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL) www.ti.com

4.21 Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL)

The RDWR_LVL_RMP_CTRL register is described in the figure and table below.

Figure 4-21. Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL)

31 30 0
RDWR_ Reserved
LVL_EN
RW=0x0 R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-23. Read-Write Leveling Ramp Control Register (RDWR_LVL_RMP_CTRL) Field

Descriptions
Bit Field Attribute Description
31 RDWR_LVL_EN RW Value = 0x0
Global Read-Write leveling enable.
• 0 Disable leveling (full and incremental)
• 1 Enable leveling (full and incremental)
30-0 Reserved R Value = 0x0
These bits are reserved, as ramp incremental leveling is not supported on
Keystone-I devices.

78 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Read-Write Leveling Control Register (RDWR_LVL_CTRL)

4.22 Read-Write Leveling Control Register (RDWR_LVL_CTRL)

The RDWR_LVL_CTRL register is described in the figure and table below.

Figure 4-22. Read-Write Leveling Control Register (RDWR_LVL_CTRL)

31 30 24 23 16 15 8 7 0
RDWRLVLFULL_START RDWRLVLINC_PRE RDLVLINC_INT RDLVLGATEINC_INT WRLVLINC_INT
RW=0x0 RW=0x0 RW=0x0 RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-24. Read-Write Leveling Control Register (RDWR_LVL_CTRL) Field Descriptions

Bit Field Description
31 RDWRLVLFULL_START Value = 0x0
Full leveling trigger.
• 0 No effect
• 1 Trigger full leveling. This bit will self-clear to zero.
30-24 RDWRLVLINC_PRE Value = 0x0
Incremental leveling pre-scalar in number of refresh periods. Value programmed is minus one the
required value. Refresh period is defined by REFRESH_RATE in SDRFC register.
23-16 RDLVLINC_INT Value = 0x0
Incremental read data eye training interval. Number of RDWRLVLINC_PRE intervals between
incremental read data eye training. A value of zero will disable incremental read data eye training.
15-8 RDLVLGATEINC_INT Value = 0x0
Incremental read DQS gate training interval. Number of RDWRLVLINC_PRE intervals between
incremental read DQS gate training. A value of zero will disable incremental read DQS gate
training.
7-0 WRLVLINC_INT Value = 0x0
Incremental write leveling interval. Number of RDWRLVLINC_PRE intervals between incremental
write leveling. A value of zero will disable incremental write leveling.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 79
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR PHY Control 1 Register (DDR_PHY_CTRL_1) www.ti.com

4.23 DDR PHY Control 1 Register (DDR_PHY_CTRL_1)

The DDR_PHY_CTRL_1 register is described in the following figure and table.

Figure 4-23. DDR PHY Control 1 Register (DDR_PHY_CTRL_1)

31 21 20 19 16 15 14
Reserved EN_DYN_PWRDN Reserved PHY_RST Reserved
R=0x0 RW=0x1 R=0x0 RW=0x0 R=0x0
13 12 11 10 9 8 7 5 4 0
IDLE_LOCAL_ODT WR_LOCAL_ODT RD_LOCAL_ODT Reserved READ_LATENCY
RW=0x0 RW=0x0 RW=0x1 R=0x0 RW=0xA
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-25. DDR PHY Control 1 Register (DDR_PHY_CTRL_1) Field Descriptions

Bit Field Attribute Description
31-21 Reserved R Value = 0x0
Reserved.
20 EN_DYN_PWRDN RW Value = 0x1
• Enables dynamically powering down the IO Receiver when not performing a read
1 : IO Receiver for DQ, DQS always powered up
0 : IO Receiver for DQ, DQS powered up during a read
19-16 Reserved R Value = 0x0
Reserved
15 PHY_RST RW Controls DDR3 PHY reset
• 0: Writing a 0 brings the DDR3 PHY out of reset
• 1: Writing a 1 will hold the DDR3 PHY in reset
14 Reserved R Value = 0x0
Reserved
13-12 IDLE_LOCAL_ODT RW Value = 0x0
Program controller termination during idle cycles.
11-10 WR_LOCAL_ODT RW Value = 0x0
Program controller termination during write access.
9-8 RD_LOCAL_ODT RW Value = 0x1
Program controller termination during read access.
7-5 Reserved RW Value = 0x0
Reserved
4-0 READ_LATENCY RW Value = 0xA
This field defines the read latency from DDR SDRAM in terms of DDR3 clock cycles. The
value depends on the CAS latency used. The user can choose any value between max
and min values given below. The programmed value should always be programmed as
the chosen value minus one.
• Maximum value possible = CAS latency + 7
• Minimum value possible = CAS Latency + 1

80 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Priority to Class-Of-Service Mapping Register (PRI_COS_MAP)

4.24 Priority to Class-Of-Service Mapping Register (PRI_COS_MAP)

The PRI_COS_MAP register is described in the following figure and table.

Figure 4-24. Priority to Class-Of-Service Mapping Register (PRI_COS_MAP)

31 30 16 15 14 13 12 11 10
PRI_COS_MAP_EN Reserved PRI_7_COS PRI_6_COS PRI_5_COS
RW=0x0 R=0x0 RW=0x0 RW=0x0 RW=0x0
9 8 7 6 5 4 3 2 1 0
PRI_4_COS PRI_3_COS PRI_2_COS PRI_1_COS PRI_0_COS
RW=0x0 RW=0x0 RW=0x0 RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-26. Priority to Class-Of-Service Mapping Register (PRICOSMAP) Field Descriptions

Bit Field Description
31 PRI_COS_MAP_EN Value = 0x0
Priority to Class-of-service mapping
• 0 = Disable Priority to Class-of-service mapping
• 1 = Enable Priority to Class-of-service mapping
30-16 Reserved Value = 0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.
15-14 PRI_7_COS Class-of-service for commands with priority of 7 (lowest priority).
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
13-12 PRI_6_COS Class-of-service for commands with priority of 6.
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
11-10 PRI_5_COS Class-of-service for commands with priority of 5.
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
9-8 PRI_4_COS Class-of-service for commands with priority of 4.
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
7-6 PRI_3_COS Class-of-service for commands with priority of 3.
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
5-4 PRI_2_COS Class-of-service for commands with priority of 2.
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
3-2 PRI_1_COS Class-of-service for commands with priority of 1.
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.
1-0 PRI_0_COS Class-of-service for commands with priority of 0 (highest priority).
• 1= Map to Class-of-service 1
• 2= Map to Class-of-service 2
• 0 or 3 will not assign any class of service.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 81
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Master ID to Class-Of-Service 1 Mapping Register (MSTID_COS_1_MAP) www.ti.com

4.25 Master ID to Class-Of-Service 1 Mapping Register (MSTID_COS_1_MAP)

The MSTID_COS_1_MAP register is described in the following figure and table.

Figure 4-25. Master ID to Class-Of-Service 1 Mapping Register (MSTID_COS_1_MAP)

31 30 23 22 20
MSTID_COS_1_MAP_EN MSTID_1_COS_1 MSK_1_COS_1
RW=0x0 RW=0x0 RW=0x0
19 12 11 10 9 2 1 0
MSTID_2_COS_1 MSK_2_COS_1 MSTID_3_COS_1 MSK_3_COS_1
RW=0x0 RW=0x0 RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-27. Master ID to Class-Of-Service Mapping 1 Register (MSTID_COS_1_MAP) Field

Descriptions
Bit Field Description
31 MSTID_COS_1_MAP_EN Master ID to Class-of-service 1 mapping.
• 0 = Disable Master ID to Class-of-service 1 mapping
• 1 = Enable Master ID to Class-of-service 1 mapping
30-23 MSTID_1_COS_1 Value = 0x0
Master ID value 1 for Class-of-service 1.
22-20 MSK_1_COS_1 Mask for master ID value 1 for Class-of-service 1.
• 0 = Disable masking
• 1 = Mask master ID bit 0
• 2 = Mask master ID bits 1-0
• 3 = Mask master ID bits 2-0
19-12 MSTID_2_COS_1 Value = 0x0
Master ID value 2 for Class-of-service 1.
11-10 MSK_2_COS_1 Mask for master ID value 2 for Class-of-service 1.
• 0 = Disable masking
• 1 = Mask master ID bit 0
• 2 = Mask master ID bits 1-0
• 3 = Mask master ID bits 2-0
9-2 MSTID_3_COS_1 Value = 0x0
Master ID value 3 for Class-of-service 1.
1-0 MSK_3_COS_1 Mask for master ID value 3 for Class-of-service 1.
• 0 = Disable masking
• 1 = Mask master ID bit 0
• 2 = Mask master ID bits 1-0
• 3 = Mask master ID bits 2-0

82 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Master ID to Class-Of-Service 2 Mapping Register (MSTID_COS_2_MAP)

4.26 Master ID to Class-Of-Service 2 Mapping Register (MSTID_COS_2_MAP)

The MSTID_COS_2_MAP register is described in the following figure and table.

Figure 4-26. Master ID to Class-Of-Service 2 Mapping Register (MSTID_COS_2_MAP)

31 30 23 22 20 19 12 11 10 9 2 1 0
MSTID_COS_2 MSTID_1_COS_2 MSK_1_COS_2 MSTID_2 MSK_2_COS_2 MSTID_3 MSK_3_COS_2
_MAP_EN _COS_2 _COS_2
RW=0x0 RW=0x0 RW=0x0 RW=0x0 RW=0x0 RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-28. Master ID to Class-Of-Service Mapping 2 Register (MSTID_COS_2_MAP) Field

Descriptions
Bit Field Description
31 MSTID_COS_2_MAP_EN Master ID to Class-of-service 2 mapping.
• 0 = Disable Master ID to Class-of-service 2 mapping
• 1 = Enable Master ID to Class-of-service 2 mapping
30-23 MSTID_1_COS_2 Value = 0x0
Master ID value 1 for Class-of-service 2.
22-20 MSK_1_COS_2 Mask for master ID value 1 for Class-of-service 2.
• 0 = Disable masking
• 1 = Mask master ID bit 0
• 2 = Mask master ID bits 1-0
• 3 = Mask master ID bits 2-0
19-12 MSTID_2_COS_2 Value = 0x0
Master ID value 2 for Class-of-service 2.
11-10 MSK_2_COS_2 Mask for master ID value 2 for Class-of-service 2.
• 0 = Disable masking
• 1 = Mask master ID bit 0
• 2 = Mask master ID bits 1-0
• 3 = Mask master ID bits 2-0
9-2 MSTID_3_COS_2 Value = 0x0
Master ID value 3 for Class-of-service 2.
1-0 MSK_3_COS_2 Mask for master ID value 3 for Class-of-service 2.
• 0 - Disable masking
• 1 = Mask master ID bit 0
• 2 = Mask master ID bits 1-0
• 3 = Mask master ID bits 2-0

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 83
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
ECC Control Register (ECCCTL) www.ti.com

4.27 ECC Control Register (ECCCTL)

The ECCCTL register is described in the following figure and table.

Figure 4-27. ECC Control Register (ECCCTL)

31 30 29 2 1 0
ECC_EN ECC_ADDR_RNG_PROT Reserved ECC_ADDR_RNG_2_EN ECC_ADDR_RNG_1_EN
RW=0x0 RW=0x0 R=0x0 RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-29. ECC Control Register (ECCCTL) Field Descriptions

Bit Field Description
31 ECC_EN ECC enable. Enabling ECC will cause the DDR3 controller to start the SDRAM initialization
sequence.
• 0 = Disable ECC
• 1 = Enable ECC
30 ECC_ADDR_RNG_PROT This bit is used to determine whether ECC calculation is allowed within address ranges described
by ECC Address Range 1 and 2 Registers, provided ECC_EN is set to enable ECC.
• 0 = Disable ECC calculation within address ranges defined in ECC Address Range 1 and 2
registers and enable calculation for accesses outside of these address ranges
• 1 = Enable ECC calculation within address ranges defined in ECC Address Range 1 and 2
registers and disable calculation for accesses outside of these address ranges
29-2 Reserved Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.
1 ECC_ADDR_RNG_2_EN ECC Address Range 2 enable.
• 0 = Disable ECC Address Range 2
• 1 = Enable ECC Address Range 2
0 ECC_ADDR_RNG_1_EN ECC Address Range 1 enable.
• 0 = Disable ECC Address Range 1
• 1 = Enable ECC Address Range 1

84 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com ECC Address Range 1 Register (ECCADDR1)

4.28 ECC Address Range 1 Register (ECCADDR1)

The ECCADDR1 register is described in the following figure and table.

Figure 4-28. ECC Address Range 1 Register (ECCADDR1)

31 16 15 0
ECC_END_ADDR_1 ECC_STRT_ADDR_1
RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-30. ECC Address Range 1 Register Field Descriptions

Bit Field Description
31-16 ECC_END_ADDR_1 End address [32-17] of 33-bit address for ECC address range 1
15-0 ECC_STRT_ADDR_1 Start address [32-17] of 33-bit address for ECC address range 1

NOTE: The range is inclusive of start and end addresses.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 85
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
ECC Address Range 2 Register (ECCADDR2) www.ti.com

4.29 ECC Address Range 2 Register (ECCADDR2)

The ECCADDR2 register is described in the following figure and table.

Figure 4-29. ECC Address Range 2Register (ECCADDR2)

31 16 15 0
ECC_END_ADDR_2 ECC_STRT_ADDR_2
RW=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-31. ECC Address Range 2 Register Field Descriptions

Bit Field Description
31-16 ECC_END_ADDR_2 End address [32-17] of 33-bit address for ECC address range 2
15-0 ECC_STRT_ADDR_2 Start address [32-17] of 33-bit address for ECC address range 2

NOTE: The range is inclusive of start and end addresses.

86 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Read Write Execution Threshold Register (RWTHRESH)

4.30 Read Write Execution Threshold Register (RWTHRESH)

The RWTHRESH register is described in the following figure and table.

Figure 4-30. Read Write Execution Threshold Register (RWTHRESH)

31 13 12 8 7 5 4 0
Reserved WR_THRSH Reserved RD_THRSH
R=0x0 RW=0x3 R=0x0 RW=0x5
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-32. Read Write Execution Threshold Register (RWTHRESH) Field Descriptions
Bit Field Description
31-13 Reserved Value = 0x0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.
12-8 WR_THRSH Write Threshold. Number of SDRAM write bursts after which the arbitration will switch to executing read
commands. The value programmed is always minus 1 the required number.
7-5 Reserved Value = 0x0
Reserved. The reserved bit location is always read as 0. A value written to this field has no effect.
4-0 RD_THRSH Read Threshold. Number of SDRAM read bursts after which the arbitration will switch to executing write
commands. The value programmed is always minus 1 the required number.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 87
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 0 Register (DDR3_CONFIG_0) www.ti.com

4.31 DDR3 Configuration 0 Register (DDR3_CONFIG_0)

The DDR3_CONFIG_0 register is described in the following figure and table.

Figure 4-31. DDR3 Configuration 0 Register (DDR3_CONFIG_0)

31 23 22 13 12 4 3 0
Reserved CMD_PHY_CTRL_SLAVE_RATIO Reserved CMD_PHY_DLL_LOCK_DIFF
R=0x0 RW=0x80 R0x0 RW=0x1
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-33. DDR3_CONFIG_0 Register (0x02620404) Field Descriptions

Bits Name Description
31-23 Reserved Reset = 0x0010000
Reserved. Do not write to this field.
22-13 CMD_PHY_CTRL_SLAVE_RATIO Reset = 0x80
Program this to 0x100 if CMD_PHY_INVERT_CLKOUT in DDR3_CONFIG_12 is set
to 1.
12-4 Reserved Reset = 0x000
3-0 CMD_PHY_DLL_LOCK_DIFF Reset = 0x1
Decides when DLL inside the DDR3 controller goes out of lock in case of jitter on the
clock. Recommend program to 0xF.

88 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 1 Register (DDR3_CONFIG_1)

4.32 DDR3 Configuration 1 Register (DDR3_CONFIG_1)

The DDR3_CONFIG_1 register is described in the following figure and table. This register is used to
program the appropriate DQ-to-DQS timing relationship during writes for C665x devices and
TCI6612/13/14. Do not program this register for any other device. Refer to the Keystone-I DDR3
Initialization app note for the proper programming sequence.

Figure 4-32. DDR3 Configuration 1 Register (DDR3_CONFIG_1)

31 25 24 18 17 0
Reserved PHY_DQ_OFFSET Reserved
R=0x0 RW=0x20 R=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-34. DDR3_CONFIG_1 Register (0x02620408) Field Descriptions

Bits Name Description
31-25 Reserved Reset = 0x0010000
Reserved. Do not write to this field.
24-18 PHY_DQ_OFFSET Reset = 0x20 for C665x/TCI6612/13/14
Reset = 0x40 for other devices
This field should be programmed to 0x40 for C665x and TCI6612/13/14 devices only,
to set the proper DQ-DQS timing relationship for writes, and left unchanged for other
devices because the default value already centers the DQ with the DQS. 0x40 is the
only valid value. Other values are not supported.
17-0 Reserved Reset = 0x000
Reserved

4.33 DDR3 Configuration 2 Register (DDR3_CONFIG_2)

The DDR3_CONFIG_2 register is described in the following figure and table.

Figure 4-33. DDR3 Configuration 2 Register (DDR3_CONFIG_2)

31 20 19 0
Reserved DATA0_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-35. DDR3_CONFIG_2 Register (0x0262040C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA0_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 3 for C665x devices or Byte
lane 7 for all other devices from the PHY calculation spreadsheet

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 89
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 3 Register (DDR3_CONFIG_3) www.ti.com

4.34 DDR3 Configuration 3 Register (DDR3_CONFIG_3)

The DDR3_CONFIG_3 register is described in the following figure and table.

Figure 4-34. DDR3 Configuration 3 Register (DDR3_CONFIG_3)

31 20 19 0
Reserved DATA1_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-36. DDR3_CONFIG_3 Register (0x02620410) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA1_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 2 for C665x devices or Byte
lane 6 for all other devices from the PHY calculation spreadsheet.

4.35 DDR3 Configuration 4 Register (DDR3_CONFIG_4)

The DDR3_CONFIG_4 register is described in the following figure and table.

Figure 4-35. DDR3 Configuration 4 Register (DDR3_CONFIG_4)

31 20 19 0
Reserved DATA2_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-37. DDR3_CONFIG_4 Register (0x02620414) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA2_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 1 for C665x devices or Byte
lane 5 for all other devices from the PHY calculation spreadsheet.

90 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 5 Register (DDR3_CONFIG_5)

4.36 DDR3 Configuration 5 Register (DDR3_CONFIG_5)

DDR3 Configuration Register 5 is used for full leveling, and is described in the following figure and table.

Figure 4-36. DDR3 Configuration 5 Register (DDR3_CONFIG_5)

31 20 19 0
Reserved DATA3_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-38. DDR3_CONFIG_5 Register (0x02620418) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA3_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 0 for C665x devices or Byte
lane 4 for all other devices from the PHY calculation spreadsheet.

4.37 DDR3 Configuration 6 Register (DDR3_CONFIG_6)

DDR3 Configuration Register 6 is used for full leveling, and is described in the following figure and table.

Figure 4-37. DDR3 Configuration 6 Register (DDR3_CONFIG_6)

31 20 19 0
Reserved DATA4_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-39. DDR3_CONFIG_6 Register (0x0262041C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA4_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 3 from the PHY calculation
spreadsheet (NA for C665x devices).

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 91
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 7 Register (DDR3_CONFIG_7) www.ti.com

4.38 DDR3 Configuration 7 Register (DDR3_CONFIG_7)

DDR3 Configuration Register 7 is used for full leveling, and is described in the following figure and table.

Figure 4-38. DDR3 Configuration 7 Register (DDR3_CONFIG_7)

31 20 19 0
Reserved DATA5_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-40. DDR3_CONFIG_7 Register (0x02620420) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA5_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 2 from the PHY calculation
spreadsheet (NA for C665x devices).

4.39 DDR3 Configuration 8 Register (DDR3_CONFIG_8)

DDR3 Configuration Register 8 is used for full leveling, and is described in the following figure and table.

Figure 4-39. DDR3 Configuration 8 Register (DDR3_CONFIG_8)

31 20 19 0
Reserved DATA6_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-41. DDR3_CONFIG_8 Register (0x02620424) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA6_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 1 from the PHY calculation
spreadsheet (NA for C665x devices).

92 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 9 Register (DDR3_CONFIG_9)

4.40 DDR3 Configuration 9 Register (DDR3_CONFIG_9)

DDR3 Configuration Register 9 is used for full leveling, and is described in the following figure and table.

Figure 4-40. DDR3 Configuration 9 Register (DDR3_CONFIG_9)

31 20 19 0
Reserved DATA7_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-42. DDR3_CONFIG_9 Register (0x02620428) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA7_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 0 from the PHY calculation
spreadsheet (NA for C665x devices).

4.41 DDR3 Configuration 10 Register (DDR3_CONFIG_10)

DDR3 Configuration Register 10 is used for full leveling, and is described in the following figure and table.

Figure 4-41. DDR3 Configuration 10 Register (DDR3_CONFIG_10)

31 20 19 0
Reserved DATA8_PHY_WRLVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-43. DDR3_CONFIG_10 Register (0x0262042C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA8_PHY_WRLVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_wrlvl_init_ratio value for Byte lane 8 (ECC byte lane) from the
PHY calculation spreadsheet (same for all devices).

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 93
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 12 Register (DDR3_CONFIG_12) www.ti.com

4.42 DDR3 Configuration 12 Register (DDR3_CONFIG_12)

DDR3 Configuration Register 12 is used if using invert clock out. See Section 2.13.7 on invert clockout for
routing conditions under which invert clock out should be used.

Figure 4-42. DDR3 Configuration 12 Register (DDR3_CONFIG_12)

31 28 27 2 25 24 23 0
6
Reserved CMD_PHY_INVERT_CLKOUT Rsvd USE_RANK0 Reserved
_DELAYS
R=0x0 RW=0x0 R0x20 RW=0x0 R0x2000000
00000
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-44. DDR3_CONFIG_12 Register (0x02620434) Field Descriptions

Bits Name Description
31-28 Reserved Reset = 0x0
Reserved.
27 CMD_PHY_INVERT_CLKOUT Reset = 0x0
• 0 - Don’t use invert clock out
• 1 - Use invert clockout.
26-25 Reserved Reset = 0x2000000
Reserved.
24 USE_RANK0_DELAYS This should be set to 1 after leveling is completed if using both chip selects for dual
rank access. Note that this is part of a sequence of steps to enable dual rank
support. See the DDR3 Initialization app note for details on how to sequence the
initialization steps for dual rank support.
23-0 Reserved Reset = 0x2000000
Reserved.

4.43 DDR3 Configuration 14 Register (DDR3_CONFIG_14)

DDR3 Configuration Register 14 is used for full leveling, and is described in the following figure and table.

Figure 4-43. DDR3 Configuration 14 Register (DDR3_CONFIG_14)

31 20 19 0
Reserved DATA0_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-45. DDR3_CONFIG_14 Register (0x0262043C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA0_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 3 for C665x devices or Byte
lane 7 for all other devices from the PHY calculation spreadsheet.

94 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 15 Register (DDR3_CONFIG_15)

4.44 DDR3 Configuration 15 Register (DDR3_CONFIG_15)

DDR3 Configuration Register 15 is used for full leveling, and is described in the following figure and table.

Figure 4-44. DDR3 Configuration 15 Register (DDR3_CONFIG_15)

31 20 19 0
Reserved DATA1_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-46. DDR3_CONFIG_15 Register (0x02620440) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA1_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 2 for C665x devices or Byte
lane 6 for all other devices from the PHY calculation spreadsheet.

4.45 DDR3 Configuration 16 Register (DDR3_CONFIG_16)

DDR3 Configuration Register 16 is used for full leveling, and is described in the following figure and table.

Figure 4-45. DDR3 Configuration 16 Register (DDR3_CONFIG_16)

31 20 19 0
Reserved DATA2_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-47. DDR3_CONFIG_16 Register (0x02620444) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA2_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 1 for C665x devices or Byte
lane 5 for all other devices from the PHY calculation spreadsheet.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 95
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 17 Register (DDR3_CONFIG_17) www.ti.com

4.46 DDR3 Configuration 17 Register (DDR3_CONFIG_17)

DDR3 Configuration Register 17 is used for full leveling, and is described in the following figure and table.

Figure 4-46. DDR3 Configuration 17 Register (DDR3_CONFIG_17)

31 20 19 0
Reserved DATA3_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-48. DDR3_CONFIG_17 Register (0x02620448) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA3_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 0 for C665x devices or Byte
lane 4 for all other devices from the PHY calculation spreadsheet.

4.47 DDR3 Configuration 18 Register (DDR3_CONFIG_18)

DDR3 Configuration Register 18 is used for full leveling, and is described in the following figure and table.

Figure 4-47. DDR3 Configuration 18 Register (DDR3_CONFIG_18)

31 20 19 0
Reserved DATA4_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-49. DDR3_CONFIG_18 Register (0x0262044C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA4_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 3 from the PHY calculation
spreadsheet (NA for C665x devices).

96 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 19 Register (DDR3_CONFIG_19)

4.48 DDR3 Configuration 19 Register (DDR3_CONFIG_19)

DDR3 Configuration Register 19 is used for full leveling, and is described in the following figure and table.

Figure 4-48. DDR3 Configuration 19 Register (DDR3_CONFIG_19)

31 20 19 0
Reserved DATA5_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-50. DDR3_CONFIG_19 Register (0x02620450) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA5_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 2 from the PHY calculation
spreadsheet (NA for C665x devices).

4.49 DDR3 Configuration 20 Register (DDR3_CONFIG_20)

DDR3 Configuration Register 20 is used for full leveling, and is described in the following figure and table.

Figure 4-49. DDR3 Configuration 20 Register (DDR3_CONFIG_20)

31 20 19 0
Reserved DATA6_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-51. DDR3_CONFIG_20 Register (0x02620454) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA6_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 1 from the PHY calculation
spreadsheet (NA for C665x devices).

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 97
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 21 Register (DDR3_CONFIG_21) www.ti.com

4.50 DDR3 Configuration 21 Register (DDR3_CONFIG_21)

DDR3 Configuration Register 21 is used for full leveling, and is described in the following figure and table.

Figure 4-50. DDR3 Configuration 21 Register (DDR3_CONFIG_21)

31 20 19 0
Reserved DATA7_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-52. DDR3_CONFIG_21 Register (0x02620458) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA7_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 0 from the PHY calculation
spreadsheet (NA for C665x devices).

4.51 DDR3 Configuration 22 Register (DDR3_CONFIG_22)

DDR3 Configuration Register 22 is used for full leveling, and is described in the following figure and table.

Figure 4-51. DDR3 Configuration 22 Register (DDR3_CONFIG_22)

31 20 19 0
Reserved DATA8_PHY_GATELVL_INIT_RATIO
R=0x0 RW=0x0
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-53. DDR3_CONFIG_22 Register (0x0262045C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA8_PHY_GATELVL_INIT_RATIO Reset = 0x0
Plug in the reg_phy_gatelvl_init_ratio value for Byte lane 8 (ECC byte lane) from the
PHY calculation spreadsheet (same for all devices).

98 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 23 Register (DDR3_CONFIG_23)

4.52 DDR3 Configuration 23 Register (DDR3_CONFIG_23)

NOTE: NA for TCI6612/13/14 and C665x devices.

DDR3 Configuration Register 23 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-52. DDR3 Configuration 23 Register (DDR3_CONFIG_23)

31 30 29 20 19 10 9 0
Reserved WR_DATA_SLAVE_RATIO WR_DQS_SLAVE_RATIO RD_DQS_SLAVE_RATIO
R=0x0 RW=0xA6 RW=0x66 RW=0x34
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-54. DDR3_CONFIG_23 Register (0x02620460) Field Descriptions

Bits Name Description
31-30 Reserved Reset = 0x0
Reserved.
29-20 WR_DATA_SLAVE_RATIO Reset = 0xA6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet.
19-10 WR_DQS_SLAVE_RATIO Reset = 0x66
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet.
9-0 RD_DQS_SLAVE_RATIO Reset = 0x34
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet.

4.53 DDR3 Configuration 24 Register (DDR3_CONFIG_24)

NOTE: NA for TCI6612/13/14 and C665x devices.

DDR3 Configuration Register 24 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-53. DDR3 Configuration 24 Register (DDR3_CONFIG_24)

31 11 10 0
Reserved FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xF
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-55. DDR3_CONFIG_24 Register (0x02620464) Field Descriptions

Bits Name Description
31-11 Reserved Reset = 0x0
Reserved.
10-0 FIFO_WE_SLAVE_RATIO Reset = 0x15
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 99
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 25 Register (DDR3_CONFIG_25) www.ti.com

4.54 DDR3 Configuration 25 Register (DDR3_CONFIG_25)

DDR3 Configuration Register 25 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-54. DDR3 Configuration 25 Register (DDR3_CONFIG_25)

31 22 21 0
Reserved DATA0_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-56. DDR3_CONFIG_25 Register (0x02620468) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA0_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for C665x devices or Byte lane 7 for TCI6612/13/14.

4.55 DDR3 Configuration 26 Register (DDR3_CONFIG_26)

DDR3 Configuration Register 26 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-55. DDR3 Configuration 26 Register (DDR3_CONFIG_26)

31 22 21 0
Reserved DATA1_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-57. DDR3_CONFIG_26 Register (0x0262046C) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA1_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for C665x devices or Byte lane 6 for TCI6612/13/14.

100 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 27 Register (DDR3_CONFIG_27)

4.56 DDR3 Configuration 27 Register (DDR3_CONFIG_27)

DDR3 Configuration Register 27 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-56. DDR3 Configuration 27 Register (DDR3_CONFIG_27)

31 22 21 0
Reserved DATA2_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-58. DDR3_CONFIG_27 Register (0x02620470) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA2_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for C665x devices or Byte lane 5 for TCI6612/13/14.

4.57 DDR3 Configuration 28 Register (DDR3_CONFIG_28)

DDR3 Configuration Register 28 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-57. DDR3 Configuration 28 Register (DDR3_CONFIG_28)

31 22 21 0
Reserved DATA3_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-59. DDR3_CONFIG_28 Register (0x02620474) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA3_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for C665x devices or Byte lane 4 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 101
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 29 Register (DDR3_CONFIG_29) www.ti.com

4.58 DDR3 Configuration 29 Register (DDR3_CONFIG_29)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 29 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-58. DDR3 Configuration 29 Register (DDR3_CONFIG_29)

31 22 21 0
Reserved DATA4_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-60. DDR3_CONFIG_29 Register (0x02620478) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA4_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for TCI6612/13/14.

4.59 DDR3 Configuration 30 Register (DDR3_CONFIG_30)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 30 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-59. DDR3 Configuration 30 Register (DDR3_CONFIG_30)

31 22 21 0
Reserved DATA5_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-61. DDR3_CONFIG_30 Register (0x0262047C) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA5_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for TCI6612/13/14.

102 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 31 Register (DDR3_CONFIG_31)

4.60 DDR3 Configuration 31 Register (DDR3_CONFIG_31)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 31 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-60. DDR3 Configuration 31 Register (DDR3_CONFIG_31)

31 22 21 0
Reserved DATA6_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-62. DDR3_CONFIG_31 Register (0x02620480) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA6_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for TCI6612/13/14.

4.61 DDR3 Configuration 32 Register (DDR3_CONFIG_32)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 32 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-61. DDR3 Configuration 32 Register (DDR3_CONFIG_32)

31 22 21 0
Reserved DATA7_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-63. DDR3_CONFIG_32 Register (0x02620484) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA7_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 103
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 33 Register (DDR3_CONFIG_33) www.ti.com

4.62 DDR3 Configuration 33 Register (DDR3_CONFIG_33)

DDR3 Configuration Register 33 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-62. DDR3 Configuration 33 Register (DDR3_CONFIG_33)

31 22 21 0
Reserved DATA_ECC_FIFO_WE_SLAVE_RATIO
R=0x0 RW=0xAD95B
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-64. DDR3_CONFIG_33 Register (0x02620488) Field Descriptions

Bits Name Description
31-22 Reserved Reset = 0x0
Reserved.
21-0 DATA_ECC_FIFO_WE_SLAVE_RATIO Reset = 0x000AD95B
Plug in the effective reg_phy_fifo_we_slave_ratio value from the PHY calculation
spreadsheet for ECC Byte lane (same for both devices).

4.63 DDR3 Configuration 34 Register (DDR3_CONFIG_34)

DDR3 Configuration Register 34 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-63. DDR3 Configuration 34 Register (DDR3_CONFIG_34)

31 20 19 0
Reserved DATA0_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-65. DDR3_CONFIG_34 Register (0x0262048C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA0_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for C665x devices or Byte lane 7 for TCI6612/13/14.

104 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 35 Register (DDR3_CONFIG_35)

4.64 DDR3 Configuration 35 Register (DDR3_CONFIG_35)

DDR3 Configuration Register 35 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-64. DDR3 Configuration 35 Register (DDR3_CONFIG_35)

31 20 19 0
Reserved DATA1_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-66. DDR3_CONFIG_35 Register (0x02620490) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA1_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for C665x devices or Byte lane 6 for TCI6612/13/14.

4.65 DDR3 Configuration 36 Register (DDR3_CONFIG_36)

DDR3 Configuration Register 36 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-65. DDR3 Configuration 36 Register (DDR3_CONFIG_36)

31 20 19 0
Reserved DATA2_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-67. DDR3_CONFIG_36 Register (0x02620494) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA2_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for C665x devices or Byte lane 5 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 105
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 37 Register (DDR3_CONFIG_37) www.ti.com

4.66 DDR3 Configuration 37 Register (DDR3_CONFIG_37)

DDR3 Configuration Register 37 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-66. DDR3 Configuration 37 Register (DDR3_CONFIG_37)

31 20 19 0
Reserved DATA3_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-68. DDR3_CONFIG_37 Register (0x02620498) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA3_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for C665x devices or Byte lane 4 for TCI6612/13/14.

4.67 DDR3 Configuration 38 Register (DDR3_CONFIG_38)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 38 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-67. DDR3 Configuration 38 Register (DDR3_CONFIG_38)

31 20 19 0
Reserved DATA4_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-69. DDR3_CONFIG_38 Register (0x0262049C) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA4_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for TCI6612/13/14.

106 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 39 Register (DDR3_CONFIG_39)

4.68 DDR3 Configuration 39 Register (DDR3_CONFIG_39)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 39 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-68. DDR3 Configuration 39 Register (DDR3_CONFIG_39)

31 20 19 0
Reserved DATA5_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-70. DDR3_CONFIG_39 Register (0x026204A0) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA5_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for TCI6612/13/14.

4.69 DDR3 Configuration 40 Register (DDR3_CONFIG_40)

NOTE: (TCI6612/13/14 only)

DDR3 Configuration Register 40 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-69. DDR3 Configuration 40 Register (DDR3_CONFIG_40)

31 20 19 0
Reserved DATA6_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-71. DDR3_CONFIG_40 Register (0x026204A4) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA6_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 107
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 41 Register (DDR3_CONFIG_41) www.ti.com

4.70 DDR3 Configuration 41 Register (DDR3_CONFIG_41)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 41 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-70. DDR3 Configuration 41 Register (DDR3_CONFIG_41)

31 20 19 0
Reserved DATA7_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-72. DDR3_CONFIG_41 Register (0x026204A8) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA7_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for TCI6612/13/14.

4.71 DDR3 Configuration 42 Register (DDR3_CONFIG_42)

DDR3 Configuration Register 42 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-71. DDR3 Configuration 42 Register (DDR3_CONFIG_42)

31 20 19 0
Reserved DATA_ECC_WR_DATA_SLAVE_RATIO
R=0x0 RW=0x298A6
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-73. DDR3_CONFIG_42 Register (0x026204AC) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA_ECC_WR_DATA_SLAVE_RATIO Reset = 0x000298A6
Plug in the effective reg_phy_wr_data_slave_ratio value from the PHY calculation
spreadsheet for ECC Byte lane (same for both devices)

108 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 43 Register (DDR3_CONFIG_43)

4.72 DDR3 Configuration 43 Register (DDR3_CONFIG_43)

DDR3 Configuration Register 43 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-72. DDR3 Configuration 43 Register (DDR3_CONFIG_43)

31 20 19 0
Reserved DATA0_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-74. DDR3_CONFIG_43 Register (0x026204B0) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA0_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for C665x devices or Byte lane 7 for TCI6612/13/14.

4.73 DDR3 Configuration 44 Register (DDR3_CONFIG_44)

DDR3 Configuration Register 44 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-73. DDR3 Configuration 44 Register (DDR3_CONFIG_44)

31 20 19 0
Reserved DATA1_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-75. DDR3_CONFIG_44 Register (0x026204B4) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA1_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for C665x devices or Byte lane 6 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 109
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 45 Register (DDR3_CONFIG_45) www.ti.com

4.74 DDR3 Configuration 45 Register (DDR3_CONFIG_45)

DDR3 Configuration Register 45 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-74. DDR3 Configuration 45 Register (DDR3_CONFIG_45)

31 20 19 0
Reserved DATA2_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-76. DDR3_CONFIG_45 Register (0x026204B8) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA2_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for C665x devices or Byte lane 5 for TCI6612/13/14.

4.75 DDR3 Configuration 46 Register (DDR3_CONFIG_46)

DDR3 Configuration Register 46 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-75. DDR3 Configuration 46 Register (DDR3_CONFIG_46)

31 20 19 0
Reserved DATA3_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-77. DDR3_CONFIG_46 Register (0x026204BC) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA3_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for C665x devices or Byte lane 4 for TCI6612/13/14.

110 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 47 Register (DDR3_CONFIG_47)

4.76 DDR3 Configuration 47 Register (DDR3_CONFIG_47)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 47 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-76. DDR3 Configuration 47 Register (DDR3_CONFIG_47)

31 20 19 0
Reserved DATA4_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-78. DDR3_CONFIG_47 Register (0x026204C0) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA4_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for TCI6612/13/14.

4.77 DDR3 Configuration 48 Register (DDR3_CONFIG_48)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 48 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-77. DDR3 Configuration 48 Register (DDR3_CONFIG_48)

31 20 19 0
Reserved DATA5_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-79. DDR3_CONFIG_48 Register (0x026204C4) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA5_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 111
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 49 Register (DDR3_CONFIG_49) www.ti.com

4.78 DDR3 Configuration 49 Register (DDR3_CONFIG_49)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 49 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-78. DDR3 Configuration 49 Register (DDR3_CONFIG_49)

31 20 19 0
Reserved DATA6_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-80. DDR3_CONFIG_49 Register (0x026204C8) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA6_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for TCI6612/13/14.

4.79 DDR3 Configuration 50 Register (DDR3_CONFIG_50)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 50 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-79. DDR3 Configuration 50 Register (DDR3_CONFIG_50)

31 20 19 0
Reserved DATA7_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-81. DDR3_CONFIG_50 Register (0x026204CC) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA7_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for TCI6612/13/14.

112 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 51 Register (DDR3_CONFIG_51)

4.80 DDR3 Configuration 51 Register (DDR3_CONFIG_51)

DDR3 Configuration Register 51 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-80. DDR3 Configuration 51 Register (DDR3_CONFIG_51)

31 20 19 0
Reserved DATA_ECC_WR_DQS_SLAVE_RATIO
R=0x0 RW=0x19866
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-82. DDR3_CONFIG_51 Register (0x026204D0) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA_ECC_WR_DQS_SLAVE_RATIO Reset = 0x00019866
Plug in the effective reg_phy_wr_dqs_slave_ratio value from the PHY calculation
spreadsheet for ECC Byte lane (same for both devices)

4.81 DDR3 Configuration 52 Register (DDR3_CONFIG_52)

DDR3 Configuration Register 52 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-81. DDR3 Configuration 52 Register (DDR3_CONFIG_52)

31 20 19 0
Reserved DATA0_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-83. DDR3_CONFIG_52 Register (0x026204D4) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA0_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 3 for C665x devices or Byte Lane 7 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 113
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 53 Register (DDR3_CONFIG_53) www.ti.com

4.82 DDR3 Configuration 53 Register (DDR3_CONFIG_53)

DDR3 Configuration Register 53 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-82. DDR3 Configuration 53 Register (DDR3_CONFIG_53)

31 20 19 0
Reserved DATA1_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-84. DDR3_CONFIG_53 Register (0x026204D8) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA1_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 2 for C665x devices or Byte Lane 6 for TCI6612/13/14.

4.83 DDR3 Configuration 54 Register (DDR3_CONFIG_54)

DDR3 Configuration Register 54 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-83. DDR3 Configuration 54 Register (DDR3_CONFIG_54)

31 20 19 0
Reserved DATA2_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-85. DDR3_CONFIG_54 Register (0x026204DC) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA2_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 1 for C665x devices or Byte Lane 5 for TCI6612/13/14.

114 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 55 Register (DDR3_CONFIG_55)

4.84 DDR3 Configuration 55 Register (DDR3_CONFIG_55)

DDR3 Configuration Register 55 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-84. DDR3 Configuration 55 Register (DDR3_CONFIG_55)

31 20 19 0
Reserved DATA3_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-86. DDR3_CONFIG_55 Register (0x026204E0) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA3_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte lane 0 for C665x devices or Byte Lane 4 for TCI6612/13/14.

4.85 DDR3 Configuration 56 Register (DDR3_CONFIG_56)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 56 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-85. DDR3 Configuration 56 Register (DDR3_CONFIG_56)

31 20 19 0
Reserved DATA4_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-87. DDR3_CONFIG_56 Register (0x026204E4) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA4_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte Lane 3 for TCI6612/13/14.

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 115
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 57 Register (DDR3_CONFIG_57) www.ti.com

4.86 DDR3 Configuration 57 Register (DDR3_CONFIG_57)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 57 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-86. DDR3 Configuration 57 Register (DDR3_CONFIG_57)

31 20 19 0
Reserved DATA5_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-88. DDR3_CONFIG_57 Register (0x026204E8) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA5_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte Lane 2 for TCI6612/13/14.

4.87 DDR3 Configuration 58 Register (DDR3_CONFIG_58)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 58 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-87. DDR3 Configuration 58 Register (DDR3_CONFIG_58)

31 20 19 0
Reserved DATA6_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-89. DDR3_CONFIG_58 Register (0x026204EC) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA6_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte Lane 1 for TCI6612/13/14.

116 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com DDR3 Configuration 59 Register (DDR3_CONFIG_59)

4.88 DDR3 Configuration 59 Register (DDR3_CONFIG_59)

NOTE: TCI6612/13/14 only.

DDR3 Configuration Register 59 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-88. DDR3 Configuration 59 Register (DDR3_CONFIG_59)

31 20 19 0
Reserved DATA7_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-90. DDR3_CONFIG_59 Register (0x026204F0) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA7_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for Byte Lane 0 for TCI6612/13/14.

4.89 DDR3 Configuration 60 Register (DDR3_CONFIG_60)

DDR3 Configuration Register 60 is used for forced ratio leveling, and is described in the following figure
and table.

Figure 4-89. DDR3 Configuration 60 Register (DDR3_CONFIG_60)

31 20 19 0
Reserved DATA_ECC_RD_DQS_SLAVE_RATIO
R=0x0 RW=0xD034
Legend: R = Read only; W = Write only; - n = value after reset; -x, value is indeterminate — see the device-specific data manual

Table 4-91. DDR3_CONFIG_60 Register (0x026204F4) Field Descriptions

Bits Name Description
31-20 Reserved Reset = 0x0
Reserved.
19-0 DATA_ECC_RD_DQS_SLAVE_RATIO Reset = 0x0000D034
Plug in the effective reg_phy_rd_dqs_slave_ratio value from the PHY calculation
spreadsheet for ECC Byte Lane (same for both devices)

SPRUGV8E – November 2010 – Revised January 2015 DDR3 Memory Controller Registers 117
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
DDR3 Configuration 60 Register (DDR3_CONFIG_60) www.ti.com

118 DDR3 Memory Controller Registers SPRUGV8E – November 2010 – Revised January 2015
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
www.ti.com Revision History

Revision History

Changes from D Revision (April 2014) to E Revision ..................................................................................................... Page

• Updated Self-Refresh Mode section. .................................................................................................. 30

• Added Dual Rank Support section. .................................................................................................... 34
• Updated Ramp Incremental Leveling section. ....................................................................................... 36
• Updated SDRAM Configuration Register (SDCFG). ................................................................................ 57
• Updated SDRAM Timing 2 (SDTIM2) Register. ..................................................................................... 61
• Updated SDRAM Timing 3 (SDTIM3) Register. ..................................................................................... 62
• Updated Read-Write Leveling Ramp Window Register. ............................................................................ 77
• Updated Read-Write Leveling Ramp Control Register. ............................................................................. 78
• Updated Read-Write Leveling Control Register. ..................................................................................... 79
• Added DDR3 Configuration 1 Register (DDR3_CONFIG_1). ...................................................................... 89
• Added Bit 24: USE_RANK0_DELAYS to DDR3_CONFIG_12 Register (0x02620434). ....................................... 94

SPRUGV8E – November 2010 – Revised January 2015 Revision History 119

Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
 IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated