Freightliner BC M2 Driver Manual PDF

®
BUSINESS CLASS M2
Driver’s Manual
STI-455-6
A24-01238-000
Truck-Manuals.net
Foreword
Introduction performed. The EDR is designed to record data re-

lated to vehicle dynamics and safety systems for ap-
This manual provides information needed to operate proximately 60 seconds. This data can help provide
and understand the vehicle and its components. a better understanding of the circumstances in which
More detailed information is contained in the Owner’s crashes and injuries occur. Data recorded includes
Warranty Information for North America booklet, and the following items:
in the vehicle’s workshop and maintenance manuals. • how various systems in the vehicle were oper-
Custom-built Freightliner vehicles are equipped with ating
various chassis and cab components. Not all of the • engine system information
information contained in this manual applies to every
vehicle. For details about components in your ve- • how far (if at all) the driver was depressing the
hicle, refer to the chassis specification pages in- accelerator
cluded in all new vehicles and to the vehicle specifi-
• if the driver was depressing the brake pedal
cation decal, located inside the vehicle.
• how fast the vehicle was traveling
For your reference, keep this manual in the vehicle
at all times. NOTE: Data is not recorded by the EDR under
IMPORTANT: Descriptions and specifications in normal driving conditions. Personal data such
this manual were in effect at the time of printing. as name, gender, age, and crash location are
Freightliner Trucks reserves the right to discon- not recorded. However, other parties such as
tinue models and to change specifications or law enforcement could combine the EDR data
design at any time without notice and without with the type of personally identifying data rou-
incurring obligation. Descriptions and specifica- tinely acquired during a crash investigation.
tions contained in this publication provide no To read data recorded by an EDR, special equipment
warranty, expressed or implied, and are subject is required, and access to the vehicle or the EDR is
to revisions and editions without notice. needed. In addition to the vehicle manufacturer, other
parties that have the special equipment, such as law
Environmental Concerns and enforcement, can read the information if they have
access to the vehicle or the EDR.
Recommendations
Whenever you see instructions in this manual to dis- Emissions and Fuel Efficiency
card materials, you should first attempt to reclaim Compliance
and recycle them. To preserve our environment, fol-
low appropriate environmental rules and regulations This vehicle must be regularly inspected and main-
when disposing of materials. tained as indicated in the Business Class M2 Mainte-
nance Manual, and in the Pretrip and Post-Trip In-
Event Data Recorder spections and Maintenance chapter in this manual, in
order to continue satisfactory performance and en-
This vehicle is equipped with one or more devices sure coverage of the vehicle under the manufactur-
that record specific vehicle data. The type and er’s warranty. Many maintenance procedures ensure
amount of data recorded varies depending on how that the vehicle and engine continue to comply with
the vehicle is equipped (such as the brand of engine, applicable emissions standards. Maintenance proce-
if an air bag is installed, or if the vehicle features a dures, using components engineered to comply with
collision avoidance system, etc.). greenhouse gas emissions and fuel efficiency regula-
tions, may be performed by an authorized Daimler
This vehicle is equipped with an event data recorder Trucks North America dealer, an independent outlet,
(EDR). The main purpose of an EDR is to record or the vehicle owner or operator.
data in certain crash or near-crash situations, such
as air bag deployment or hitting a road obstacle, that The vehicle owner is responsible for determining the
will assist in understanding how a vehicle’s systems suitability of replacement components to maintain
STI-455-6 (11/14)
A24-01238-000
Printed in U.S.A.
Truck-Manuals.net
Foreword
compliance with federal and local jurisdictional regu- hotline 1-800-333-0510, or contact Transport
lations. Components including, but not limited to, Canada by mail at: Transport Canada, ASFAD,
tires, cab/sleeper side extenders, chassis fairings, Place de Ville Tower C, 330 Sparks Street, Ot-
bumper, hood, vehicle speed limiters, and idle reduc- tawa, Ontario, Canada K1A 0N5.
tion timers are specifically designed and manufac-
tured to exacting standards for regulatory fuel effi- For additional road safety information, please visit
ciency and greenhouse gas emissions compliance. It the Road Safety website at: www.tc.gc.ca/
is important that these components are always re- roadsafety.
placed with components that meet or exceed the per-
formance of the originally installed components.
Customer Assistance Center

Having trouble finding service? Call the Customer
Assistance Center at 1-800-385-4357 or 1-800-FTL-
HELP. Call night or day, weekdays or weekends, for
dealer referral, vehicle information, breakdown coor-
dination, or Fleetpack assistance. Our people are
knowledgeable, professional, and committed to fol-
lowing through to help you keep your truck moving.
Reporting Safety Defects

If you believe that your vehicle has a defect which
could cause a crash or could cause injury or
death, you should immediately inform the National
Highway Traffic Safety Administration (NHTSA) in
addition to notifying Daimler Trucks North America
LLC.
If the NHTSA receives similar complaints, it may
open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order a
recall and remedy campaign. However, NHTSA
cannot become involved in individual problems
between you, your dealer, or Daimler Trucks North
America LLC.
To contact NHTSA, you may call the Vehicle
Safety Hotline toll-free at 1-888-327-4236 (TTY:
1-800-424-9153); go to www.safercar.gov; or
write to: Administrator, NHTSA, 1200 New Jersey
Avenue, SE, Washington, DC 20590. You can also
obtain other information about motor vehicle safety
from www.safercar.gov.
Canadian customers who wish to report a safety-
related defect to Transport Canada, Defect Investi-
gations and Recalls, may telephone the toll-free
© 2001–2015 Daimler Trucks North America LLC. All rights reserved. Daimler Trucks North America LLC is a Daimler
company.
No part of this publication, in whole or part, may be translated, reproduced, stored in a retrieval system, or transmitted
in any form by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written per-
mission of Daimler Trucks North America LLC. For additional information, please contact Daimler Trucks North
America LLC, Service Systems and Documentation, P.O. Box 3849, Portland OR 97208–3849 U.S.A. or refer to
www.Daimler-TrucksNorthAmerica.comand www.FreightlinerTrucks.com.
Truck-Manuals.net
Contents
Chapter Page
Introduction, Environmental Concerns and Recommendations,
Event Data Recorder, Emissions and Fuel Efficiency Compliance,
Customer Assistance Center, Reporting Safety Defects . . . . . . . . . . . . . . . . . . . . Foreword
1 Vehicle Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
2 Vehicle Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1
3 Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
4 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
5 Cab Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
6 Heater, Ventilator and Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1
7 Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1
8 Drivetrain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1
9 Steering and Brake Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1
10 Fifth Wheels and Trailer Couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1
11 Pretrip and Post-Trip Inspections and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1
12 Cab Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1
13 In an Emergency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1
14 Headlight Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1
15 Hybrid Electric Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1
16 Natural Gas Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I.1
Truck-Manuals.net
1
Vehicle Identification
Component Information Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Federal Motor Vehicle Safety Standard Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Canadian Motor Vehicle Safety Standard Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Component GWR Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Emission Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Truck-Manuals.net
Component Information Label The tire and rim portion of the FMVSS certification
label certifies suitable tire and rim combinations that
NOTE: Labels shown in this chapter are ex- can be installed on the vehicle, for the given gross
amples only. Actual specifications may vary from axle weight rating. Tires and rims installed on the
vehicle to vehicle. vehicle at the time of manufacture may have a higher
load capacity than that certified by the tire and rim
The component information label lists the vehicle label. If the tires and rims currently on the vehicle
model, identification number, and major component have a lower load capacity than that shown on the
models. It also lists the major assemblies and instal- tire and rim label, then the tires and rims determine
lations shown on the chassis specification sheet. the load limitations on each of the axles.
One copy of the component information label is in-
stalled on the right-side dash; another copy is inside Trucks built without a cargo body that are intended
the rear cover of the Owner’s Warranty Information for service in the U.S. have an incomplete vehicle
for North America booklet. An illustration of the label certification label attached by the final-stage manu-
is shown in Fig. 1.1. facturer. See Fig. 1.4. This label will be attached to
the incomplete vehicle document included with the
vehicle, and certifies that the vehicle conforms to all
applicable FMVSS regulations in effect on the date of
completion.
Canadian Motor Vehicle Safety

Standard Labels
In Canada, tractors with fifth wheels are marked as
certified by means of a statement of compliance label
with the Canadian National Safety Mark attached to
the driver-side door frame B-pillar. See Fig. 1.5.
02/20/2012 f080176
If purchased for service in Canada, trucks built with-
Fig. 1.1, Component Information Label out a cargo body and tractors built without a fifth
wheel are marked as certified by a "Statement of
Federal Motor Vehicle Safety Compliance" label, similar to Fig. 1.4. This label must
be attached by the final-stage manufacturer to certify
Standard Labels that the vehicle conforms to all applicable Canada
Motor Vehicle Safety Standard (CMVSS) regulations
NOTE: Due to the variety of Federal Motor Ve- in effect on the date of completion.
hicle Safety Standard (FMVSS) certification re-
quirements, not all of the labels shown will apply
to your vehicle. Component GWR Label
Tractors with or without fifth wheels purchased in the The component GWR label is located on the
U.S. are marked as certified by means of an FMVSS passenger-side B-pillar. The label provides maximum
certification label. See Fig. 1.2. This label is attached GWR ratings for each component.
to the driver-side B-pillar, as shown in Fig. 1.3.
02/20/2012 f080177
Fig. 1.2, Vehicle Certification Label
1.1
Truck-Manuals.net
Emission Labels
Aftertreatment System Indicators
Label
1
Engines and vehicles manufactured after December
31, 2006 and domiciled in the U.S. or Canada are
required to meet all EPA regulations effective as of
the vehicle build date, and are equipped with an
emission aftertreatment system (ATS). Vehicles do-
miciled outside of the U.S. and Canada may not
have aftertreatment equipment, depending upon local
statutory emissions guidelines. See Table 1.1.
2 A warning label on the driver-side visor contains im-
portant warning indicators in the instrument cluster
that pertain to the ATS. See Fig. 1.7 or Fig. 1.8.
It is a violation of U.S. federal law to alter exhaust
plumbing, ATS, or other components in any way that
would bring the engine/vehicle out of compliance with
certification requirements [Ref: 42 U.S.C. S7522(a)
(3)]. It is the owner’s responsibility to maintain the
11/13/2001 f080117 vehicle so that it conforms to EPA regulations.
1. Tire and Rim Information
2. FMVSS Certification Label EPA Noise Emission Control Label
Fig. 1.3, Label Locations A vehicle noise emission control label (Fig. 1.9) is
located on the driver-side B-pillar as shown in
Fig. 1.3. It is the owner’s responsibility to maintain
the vehicle so that it conforms to EPA regulations.
IMPORTANT: Certain Freightliner incomplete
02/28/2012 f080180 vehicles may be produced with incomplete noise
control hardware and will not have a noise
Fig. 1.4, Incomplete Vehicle Certification Label emission control information label. For such ve-
hicles, it is the final-stage manufacturer’s re-
sponsibility to complete the vehicle in conformity
to EPA regulations (40 CFR Part 205) and label
it for compliance.
10/10/2006 f080024
Fig. 1.5, Canadian National Safety Mark
See Fig. 1.6 for a typical component GWR label.
1.2
Truck-Manuals.net
02/20/2012 f080178
Fig. 1.6, Component GWR Label
Applicable Emissions System Based on Build Date and EPA Regulations

Build Date Regulation: Emissions Components
EPA07 (reduce nitrogen oxides (NOx) emissions to 1.1 g/bhp-hr, and reduce
January 1, 2007–December 31,
particulate matter emissions to 0.01 g/bhp-hr): Aftertreatment device (ATD) containing
2009
a diesel particulate filter that traps soot and ash.*
EPA10 (reduce NOx emissions to 0.2 g/bhp-hr): EPA07-type ATD, with additional
January 1, 2010–December 31,
selective catalyst reduction (SCR) technology that utilizes diesel exhaust fluid (DEF)
2012
to convert NOx to nitrogen and water vapor.
GHG14: Aerodynamic and fuel efficiency components including, but not limited to,
tires, cab/sleeper side extenders, chassis fairings, bumper, hood, vehicle speed
From March 5, 2012
limiters, and idle reduction timers specifically designed to meet regulatory fuel
efficiency and greenhouse gas emissions standards.
* Cummins, Detroit, and Mercedes-Benz ATD’s are also equipped with a diesel oxidation catalyst to break down pollutants.
Table 1.1, Applicable Emissions System Based on Build Date and EPA Regulations
the engine after five minutes of idling in order to limit

Vehicle Emission Control Information emissions of particulate matter and NOx.
Label Certified vehicles are equipped with a label placed
near the bottom edge of the driver-side door. See
Model year 2013 and later vehicles meet additional Fig. 1.11.
requirements as specified by federal greenhouse gas
and fuel efficiency regulations (GHG14). These ve-
hicles are equipped with components that increase
fuel efficiency and reduce GHG emissions. Compo-
nents may include, but are not limited to, low-rolling
resistance tires; aerodynamic devices such as hood,
cab side extenders, and fuel tank fairings; vehicle
speed limiters; and idle shutdown timers.
A Vehicle Emission Control Information Label is lo-
cated on the driver-side door. See Fig. 1.10. It is the
owner’s responsibility to maintain the vehicle so that
it conforms to EPA and NHTSA regulations.
Certified Clean Idle Label

The California Air Resources Board (CARB) requires
model year 2008 and newer heavy-duty diesel en-
gines to be equipped with a non-programmable en-
gine shutdown system that automatically shuts down
1.3
Truck-Manuals.net
EXHAUST AFTERTREATMENT SYSTEM INFORMATION

INDICATOR WARNING
CHECK STOP
LAMP(S)
(Solid) (Flashing) (Flashing)
Level 1 Level 2 Level 3 Level 4
Indicator Lamp Filter Regeneration Filter Parked Regeneration Service Regeneration Required. HEST (High Exhaust
Message(s) Recommended. Regeneration Required − Engine Engine Derate To Idle Only. System Temperature)
Necessary Derate
Diesel Particulate Filter is reaching Filter is now Filter has reached Filter has exceeded maximum Flashing
Filter Condition capacity. reaching maximum maximum capacity. capacity. A regeneration is in
Switch.
capacity. progress.
Required Action Bring vehicle to To avoid engine Vehicle must be Vehicle must be parked, and a
highway speeds to derate, bring vehicle parked, and a Parked Service Regeneration must be Solid
allow for an to highway speeds Regeneration must performed. Check engine Exhaust components
Automatic to allow for an be performed. operator’s manual for details. and exhaust gas are at
Regeneration or Automatic Engine will begin Engine will shut down. high temperature. When
perform a Parked Regeneration, or derate. stationary, keep away
Regeneration. perform a Parked from people and
Regeneration as flammable materials or
soon as possible. vapors.
For a driver performed Parked Regeneration, vehicle must be equipped with a dash mounted Regeneration Switch.
02/20/2009 f080156
Fig. 1.7, ATS Indicators, EPA07
1.4
Truck-Manuals.net
IMPORTANT
DPF Regen Needed Diesel Particulate Filter (DPF)
regeneration is needed.
If flashing, regenerate as soon as
possible. Engine derate possible.
Hot Exhaust Hot exhaust can cause fire.
Keep flammables and people away
from exhaust.
DEF Refill Needed Diesel Exhaust Fluid (DEF) level is

low. Engine derate likely.
DEF
Refill tank with certified DEF.
See operator’s manual for complete instructions. 24−01656−000
11/30/2010 f080162
Fig. 1.8, ATS Indicators, EPA10 and Newer
VEHICLE NOISE EMISSION CONTROL INFORMATION

FREIGHTLINER CORPORATION DATE OF MANUFACTURE 01/96
THIS VEHICLE CONFORMS TO U.S. EPA REGULATIONS FOR NOISE EMISSION
APPLICABLE TO MEDIUM AND HEAVY TRUCKS.
THE FOLLOWING ACTS OR THE CAUSING THEREOF BY ANY PERSON ARE PROHIBITED BY
THE NOISE CONTROL ACT OF 1972:
A. THE REMOVAL OR RENDERING INOPERATIVE, OTHER THAN FOR PURPOSES OF
MAINTENANCE, REPAIR, OR REPLACEMENT, OF ANY NOISE CONTROL DEVICE OR
ELEMENT OF DESIGN (LISTED IN THE OWNER’S MANUAL) INCORPORATED INTO THIS
VEHICLE IN COMPLIANCE WITH THE NOISE CONTROL ACT.
CERTIFIED
B. THE USE THIS VEHICLE AFTER SUCH DEVICE OR ELEMENT OF DESIGN HAS
BEEN REMOVED OR RENDERED INOPERATIVE. 24−00273−020
10/06/98 f080026
Fig. 1.9, Vehicle Noise Emission Control Label CLEAN IDLE

VEHICLE EMISSION CONTROL INFORMATION
MANUFACTURED BY: DATE OF MANUFACTURE:
VIN: REGULATORY CLASS:
VEH FAMILY CD:
GVWR−KG
GVWR−LBS EMISSION CONTROL IDENTIFIERS:
THIS VEHICLE COMPLIES WITH U. S. EPA REGULATIONS FOR XXXX HEAVY DUTY VEHICLES.
SEE OWNER’S MANUAL FOR PROPER MAINTENANCE OF THIS VEHICLE. U PART NO. 24−01177−060 REV A 02/20/2012 f080179
02/29/2012 f080181
Fig. 1.11, CARB Clean Idle Label
Fig. 1.10, Vehicle Emission Control Information Label
1.5
Truck-Manuals.net
2
Vehicle Access
Cab Door Locks and Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1
Grab Handles and Access Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1
Cab Entry and Exit, Vehicles With Two Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Cab Entry and Exit, Vehicles With One Step . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4
Back-of-Cab Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5
Battery Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Hood Opening and Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7
Fuse Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8
Truck-Manuals.net
Vehicle Access
Cab Door Locks and Handles 1 2

One key operates the ignition switch and all of the
door locks. 3 4
IMPORTANT: Each key is numbered. Record

the number so a duplicate key can be made, if
needed.
To unlock the driver’s door from outside the cab, in-
sert the key in the lockset and turn it one-quarter turn
clockwise (Fig. 2.1). To remove the key, turn it coun-
terclockwise to its original position. Pull out on the
door pull handle to open the door.
2
1
10/25/2001 f720398
To open the door from the inside, lift up on the door lever
(arrow).
1. Lock Button
3 2. Armrest/Handle
3. Door Lever
4. Window Crank
5. Inner Door Grab Handle (optional)
10/22/2001 f720397
Fig. 2.2, Door Interior
1. Key 3. Door Pull Handle
2. Lock To open the door from the inside, lift up on the door
lever. This will unlatch the door whether or not it is
Fig. 2.1, Exterior Door Handle
locked. If it is open, close the door by pulling the
To unlock the passenger’s door from outside the cab, inner door grab handle.
insert the key in the lockset and turn it one-quarter To lock either door from inside the cab, slide the lock
turn counterclockwise. Turn the key clockwise to the button downwards (Fig. 2.3). To unlock the door
original position to remove it. without unlatching it, push the lock button upwards. A
NOTE: The cab door locks can be operated red dot will show below the lock button when it is
when the doors are open. unlocked.
To lock a door from outside the cab, do either one of

the following:
Grab Handles and Access
• Insert the key in the lockset and turn it in the
Steps
direction opposite to the unlocking direction For ease of entry and exit, there are three grab
(counterclockwise for the driver’s door, clock- handles, one on the A-pillar, one on the inner B-pillar,
wise for the passenger’s door). Close the door and an optional one on the inside of the door. In ad-
if it is open. dition, the steering wheel may be used to provide
• Push down the inside lock button (Fig. 2.2). secure handholds. There are one or two access
Close the door. steps to provide secure footholds.
2.1
Truck-Manuals.net
Vehicle Access
Use the cab access system (grab handles, access

steps, and steering wheel) to enter or exit the cab.
Entering from the Driver’s Side

2 To enter the cab from the driver’s side, do the follow-
ing steps (Fig. 2.4):
1
1
10/24/2001 f720401
Move the button down to lock, and up to unlock (arrows).
The door is unlocked when the red dot shows.
1. Door 3. Red Dot
2. Lock Button
Fig. 2.3, Door Lock Button 5
NOTE: The A-pillar grab handle is not installed

on the driver’s side. 2
4
The grab handles, access steps, and steering wheel
are all part of the cab access system. Use these
"helping hands" when getting into, or out of, the cab. 3
They will increase your security and comfort.
11/02/2001 f720399
Cab Entry and Exit, Vehicles 1. Steering Wheel
2. B-Pillar Grab Handle
With Two Steps 3. Bottom Step
4. Top Step
WARNING 5. Inner Door Grab Handle (optional)
Fig. 2.4, Cab Access System, Driver’s Side
Wet or dirty shoe soles greatly increase the
chance of slipping or falling. If your soles are wet 1. Use the door pull handle to open the driver’s
or dirty, be especially careful when climbing door, and place anything that you are carrying in
onto, or down from, the back-of-cab area. the cab.
Always maintain three-point contact with the 2. Grasp the B-pillar grab handle with both hands.
back-of-cab access supports while entering and Reach up as far as is comfortable.
exiting the back-of-cab area. Three-point contact
means both feet and one hand, or both hands 3. Place your right foot on the bottom step, and pull
and one foot, on the grab handles, steps, and yourself up.
deck plates. Other areas are not meant to sup- 4. Place your left foot on the top step.
port back-of-cab access, and grabbing or step-
ping in the wrong place could lead to a fall, and 5. Grasp the steering wheel with your left hand, and
personal injury. step up.
Be careful not to get hands or feet tangled in 6. Step into the cab with your right foot first, and
hoses or other back-of-cab equipment. Careless- grasp the steering wheel with your right hand.
ness could cause a person to trip and fall, with
possible injury.
2.2
Truck-Manuals.net
Vehicle Access
NOTE: You can also use the inner door grab

handle, if available, as a support when getting
up or down from the bottom step.
5
4
Exiting from the Driver’s Side
To exit the cab from the driver’s side, do the follow-
IMPORTANT: Do not attempt to exit the cab
while carrying any items in your hands.
1. If you wish to take any items with you, after you
exit the cab, place them in an accessible location
on the seat or cab floor. Make sure they will not
get in your way as you exit. 3
WARNING 2
Always face in when exiting the cab. Do not at- 1
tempt to exit with your back to the cab, as you 10/23/2001 f720400
would going down a flight of stairs. It is easier to 1. Bottom Step

slip or lose your balance. If you slip when exiting 2. Top Step
in this way, there is a greater likelihood of per- 3. B-Pillar Grab Handle
sonal injury. 4. Sidewall Grab Handle (optional)
5. A-Pillar Cover Grab Handle
2. Grasp the steering wheel with both hands. Place
your left foot on the top step, and stand on the Fig. 2.5, Cab Access System, Passenger’s Side and
threshold, facing into the cab. Back of Cab
3. Move your right hand to the B-pillar grab handle. 3. Place your left foot on the bottom step and step
up to the upper step with your right foot.
4. Move your right foot to the bottom step.
4. Move your right hand to the A-pillar cover grab
5. Move your left hand to the B-pillar grab handle. handle.
6. Step to the ground with your left foot first. 5. Place your left foot on the top step and step up.
7. Retrieve from the cab any items that you wish to 6. Move your left hand to the A-pillar cover grab
take with you. handle.
NOTE: You can also use the inner door grab 7. Step into the cab with your left foot first.
up or down from the bottom step. NOTE: You can also use the inner door grab
Entering from the Passenger’s Side up or down from the bottom step.
To enter the cab from the passenger’s side, do the Exiting from the Passenger’s Side
following steps (Fig. 2.5):
To exit the cab from the passenger’s side, do the fol-
1. Open the passenger’s door, and place anything lowing steps (Fig. 2.5):
that you are carrying in the cab.
2.
Grasp the B-pillar grab handle on the door with
both hands. while carrying any items in your hands.
1. If you wish to take any items with you, after you
exit the cab, place them in an accessible location
2.3
Truck-Manuals.net
Vehicle Access
on the seat or cab floor. Make sure they will not ness could cause a person to trip and fall, with
get in your way as you exit. possible injury.
Use the cab access system (grab handles, access
WARNING steps, and steering wheel) to enter or exit the cab.
Always face in when exiting the cab. Do not at- Entering from the Driver’s Side
tempt to exit with your back to the cab, as you
would going down a flight of stairs. It is easier to To enter the cab from the driver’s side, do the follow-
slip or lose your balance. If you slip when exiting ing steps (Fig. 2.4):
in this way, there is a greater likelihood of per-
1. Use the door pull handle to open the driver’s
sonal injury.
door, and place anything that you are carrying in
2. Grasp the A-pillar cover grab handle with both the cab. Use the door armrest/handle and, if
hands, then place your right foot on the top step available, the inner door grab handle, as a sup-
while standing up from the seat facing inward. port if needed.
3. Place your left foot on the top step. 2. Grasp the B-pillar grab handle with both hands.
Reach up as far as is comfortable.
4. Move your left hand to the B-pillar grab handle.
3. Place your right foot on the step, and pull your-
5. Move your left foot to the bottom step. self up.
6. Move your right hand to the B-pillar grab handle. 4. Step into the cab with your left foot.
7. Step to the ground with your right foot first. 5. Grasp the steering wheel with your left hand.
8. Retrieve from the cab any items that you wish to 6. Step into the cab with your right foot, and grasp
take with you. the steering wheel with your right hand.
NOTE: You can also use the inner door grab NOTE: You can also use the inner door grab
handle, if available, as a support when getting handle, if available, as a support when getting
up or down from the bottom step. up or down from the bottom step.
Cab Entry and Exit, Vehicles Exiting from the Driver’s Side
With One Step To exit the cab from the driver’s side, do the follow-
WARNING IMPORTANT: Do not attempt to exit the cab
while carrying any items in your hands.
Wet or dirty shoe soles greatly increase the
chance of slipping or falling. If your soles are wet 1. If you wish to take any items with you, after you
or dirty, be especially careful when climbing exit the cab, place them in an accessible location
onto, or down from, the back-of-cab area. on the seat or cab floor. Make sure they will not
get in your way as you exit.
Always maintain three-point contact with the
back-of-cab access supports while entering and
exiting the back-of-cab area. Three-point contact WARNING
means both feet and one hand, or both hands
and one foot, on the grab handles, steps, and Always face in when exiting the cab. Do not at-
deck plates. Other areas are not meant to sup- tempt to exit with your back to the cab, as you
port back-of-cab access, and grabbing or step- would going down a flight of stairs. It is easier to
ping in the wrong place could lead to a fall, and slip or lose your balance. If you slip when exiting
personal injury. in this way, there is a greater likelihood of per-
sonal injury.
Be careful not to get hands or feet tangled in
hoses or other back-of-cab equipment. Careless-
2.4
Truck-Manuals.net
Vehicle Access
2. Grasp the steering wheel with both hands. Place

your left foot on the step, and stand on the WARNING
threshold, facing into the cab.
Always face in when exiting the cab. Do not at-
3. Move your right hand to the B-pillar grab handle. tempt to exit with your back to the cab, as you
4. Move your left hand to the B-pillar grab handle. would going down a flight of stairs. It is easier to
slip or lose your balance. If you slip when exiting
5. Move your right foot onto the step. in this way, there is a greater likelihood of per-
6. Step to the ground with your left foot first. sonal injury.
7. 2. Grasp the A-pillar cover grab handle with both

Retrieve from the cab any items that you wish to
take with you. hands, then place your right foot on the step
while standing up from the seat facing inward.
NOTE: You can also use the inner door grab 3. Place your left foot on the step.
up or down from the bottom step. 4. Move your left hand to the B-pillar grab handle.
5. Move your right hand to the B-pillar grab handle.
Entering from the Passenger’s Side
6. Step to the ground with your right foot first.
To enter the cab from the passenger’s side, do the
following steps (Fig. 2.5): 7. Retrieve from the cab any items that you wish to
take with you.
1. Open the passenger’s door, and place anything
that you are carrying in the cab. NOTE: You can also use the inner door grab
2. Grasp the B-pillar grab handle with both hands. up or down from the bottom step.
3. Place your left foot on the step and step up to
the cab with your right foot. Back-of-Cab Access
4. Move your right hand to the A-pillar cover grab
When trailer air and electrical connections cannot be
handle.
reached conveniently from the ground, Federal Motor
5. Move your left hand to the A-pillar cover grab Carrier Safety Regulations require commercial carri-
handle. ers to provide back-of-cab access.
6. Step into the cab with your left foot. Optional grab handles are mounted on each cab
sidewall, or on the left sidewall only. See Fig. 2.6.
NOTE: You can also use the inner door grab Steps are mounted either on the fuel tank(s) or on
handle, if available, as a support when getting metal brackets. When a deck plate is necessary, it is
up or down from the bottom step. mounted across the top of the frame rails.
Exiting from the Passenger’s Side IMPORTANT: Climb onto, and down from, back-
of-cab access facing in toward the vehicle, as
To exit the cab from the passenger’s side, do the fol- you would on a ladder. Do not climb up or down
lowing steps (Fig. 2.5): facing out away from the vehicle.
while carrying any items in your hands. WARNING
1. If you wish to take any items with you, after you Wet or dirty shoe soles greatly increase the
exit the cab, place them in an accessible location chance of slipping or falling. If your soles are wet
on the seat or cab floor. Make sure they will not or dirty, be especially careful when climbing
get in your way as you exit. onto, or leaving, the back-of-cab area.
Always maintain three-point contact with the
back-of-cab access supports while entering and
2.5
Truck-Manuals.net
Vehicle Access
2. Place one foot on the bottom step and pull your-

self up.
3. Place your other foot on the top step.
4. Move your lower hand to a higher position on the
grab handle.
5. Step onto the deck plate.
Climbing Down from Back-of-Cab

To climb down from the back-of-cab area:
2 1. Grasp the sidewall grab handle with both hands.
2. Step one foot at a time onto the top step.
3
3. Move your upper hand to a lower position on the
grab handle.
4. Move one foot to the bottom step.
5. Move your upper hand to a lower position on the
grab handle.
1
6. Step to the ground with your upper foot first.
Battery Access
Battery Compartment
1
09/28/2007 f602336 The battery compartment is located in the lower part
1. Steps 3. Deck Plate of the cab beneath and to the rear of the driver’s
2. Grab Handle door. It is fastened by a quarter-turn fastener. To
open the battery access door, turn the quarter-turn
Fig. 2.6, Back-of-Cab Access Supports (typical)
fastener with a small screwdriver. See Fig. 2.7.
exiting the back-of-cab area. Three-point contact
means both feet and one hand, or both hands
and one foot, on the grab handles, steps, and
deck plates. Other areas are not meant to sup-
port back-of-cab access, and grabbing or step-
ping in the wrong place could lead to a fall, and
personal injury.
Be careful not to get hands or feet tangled in
hoses or other back-of-cab equipment. Careless-
ness could cause a person to trip and fall, with
possible injury.
Entering Back-of-Cab
When climbing onto the deck plate, do the following:
10/25/2001 f543934
1. Grasp the sidewall grab handle with both hands.
Reach up as far as is comfortable. Open the battery access door by turning the quarter-turn
fastener (arrow) with a small screwdriver.
Fig. 2.7, Battery Compartment, Closed
2.6
Truck-Manuals.net
Vehicle Access
With the battery access door open (Fig. 2.8), it is NOTE: Whenever battery power is discon-
easy to get access to the battery terminals for clean- nected, clocks and electronically tuned radios
ing, charging, or emergency jump starting. must be reset.
4
1 01/18/95 f600150a
10/24/2001 f543933
1. Top Step Fig. 2.9, Cab (Battery) Isolation Switch
2. Battery
3. Cab Hood Opening and Closing
4. Battery Access Door
The hood can be raised to a full-open position. A tor-
Fig. 2.8, Battery Compartment, Open sion bar helps you to raise the hood, and to lower it
to the operating position. Hood restraint cables pre-
To close the battery access door, do the following vent the hood from overtravel. A hood damper limits
steps: the closing speed. In the operating position, the hood
1. Swing the battery access door to line up the is secured to the cab-mounted half-fenders by a
quarter-turn fastener with the hole in the cab hold-down latch on each side of the hood.
door frame.
2. Close the battery access door and check to be
To Open the Hood
sure the quarter-turn fastener is engaged with 1. Apply the parking brakes.
the hole.
2. Release both hood hold-down latches by pulling
3. Turn the fastener one-quarter turn. the ends outward. See Fig. 2.10.
Cab (Battery) Isolation Switch CAUTION

The cab isolation switch (see Fig. 2.9) is located on
the cab floor at the left of the driver’s seat, or inside Do not let the hood free-fall to the full-open posi-
the battery box. The battery isolation switch reduces tion. To do so could cause damage to the hood
the power to the cab and engine power wiring. Use it or hood straps.
whenever the vehicle is to be put out of service for 3. Standing in front of the hood, raise the rear of
extended periods. the hood upward until it reaches the over-center
IMPORTANT: The battery disconnect switch position (45 degrees from vertical). Then slowly
bring it to a stop.
does not completely isolate the batteries from
the electrical system. For service operations that To Close the Hood
require that the batteries be disconnected, al-
ways shut down the engine and remove the 1. Push the hood over center.
negative battery cables.
2.7
Truck-Manuals.net
Vehicle Access
Fuse Identification, Main Fuse Box

Pos.
3 Description Fuse Color Rating
No.
F1 VCU (MBE900 only) Red 10 Amp
2
F2 Blower Motor Green 30 Amp
F3 Engine ECU Yellow 20 Amp
Transmission Control
F4 Green 30 Amp
Unit
4 F5 Ignition Switch Tan 5 Amp
F6 Spare — —
F7 Bulkhead Module Green 30 Amp
1 F8 ICU Red 10 Amp
10/24/2001 f880555 Transmission Control
F9 Yellow 20 Amp
1. Fender 3. Latch Handle Unit
2. Latch Hook 4. Half-Fender F10 Door Locks (optional) Red 10 Amp
F11 Mirrors (optional) Blue 15 Amp
Fig. 2.10, Hood Hold-Down Latch F12 Radio/Diagnostics Yellow 20 Amp
2. As the hood goes over center, the damper auto- F13 Chassis Module Green 30 Amp
matically slows its rate of descent. If needed, you L/H Power Windows
F14 Blue 15 Amp
can also slow its rate of descent with your hand. (optional)
3. Make sure the hood is flush with the cowl, then F16 ABS ECU Blue 15 Amp
secure the hood by engaging both hood hold- F17 Chassis Module Green 30 Amp
down latches.
IMPORTANT: Make sure that both hold-down F19 Chassis Module Green 30 Amp
latches are fully engaged before operating the F20 Bulkhead Module Green 30 Amp
vehicle. F21
R/H Power Windows
Blue 15 Amp
(optional)
Fuse Identification F22 Bulkhead Module
F23 Spare
Green
—
30 Amp
—
Main Fuse Box/PDM F24 Spare — —
F25 Spare — —
The main fuse box, also known as the power distri-
F26 Spare — —
bution module, or PDM, is located under the hood on
M1 Battery Power — 125 Amp
the left front fender just forward of the bulkhead mod-
ule. See Fig. 2.11. To open the fuse box, pull down M2 Battery Power — 125 Amp
on the wire clips holding the lid on the fuse box. M3 Battery Power — 150 Amp
A sticker inside the lid of the fuse box shows the lo- Table 2.1, Fuse Identification, Main Fuse Box
cations of the fuses and describes the circuit(s) that
each fuse protects (see Fig. 2.12). See Table 2.1 for
descriptions of a typical set of fuses. The fuses in the Trailer and Taillight Fuse Boxes
main fuse box are mini blade-type fuses. Battery The trailer fuse box and the taillight fuse box, on ve-
power fuses, located near the batteries, are bolt-in hicles so equipped, are mounted on a bracket with
megafuses. the chassis module on the left-hand frame rail aft of
Because the electrical system is multiplexed, no re- the cab, or on a crossmember at the end of the
lays are needed. The multiplexing module performs frame rail. These may be referred to as the chassis
the functions normally provided by relays. fuse box or chassis PDM. See Fig. 2.13 for trailer
fuse and relay information, and Fig. 2.14 for taillight
fuse and relay information.
2.8
Truck-Manuals.net
Vehicle Access
These fuse boxes contain mini blade-type fuses, 12-

volt mini relays, and 12-volt micro relays.
2
09/28/2004 f544528
09/25/2001 f543935
Fig. 2.13, Trailer Fuse Box Diagram
1. Bulkhead Module 2. Main Fuse Box
Fig. 2.11, Location of the Main Fuse Box
10/25/2001 f543936
10/07/2004 f544541
Fig. 2.12, Main Fuse Box Diagram
Fig. 2.14, Taillight Fuse Box Diagram
2.9
Truck-Manuals.net
3
Instruments
Instrumentation Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Warning and Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2
Driver Message Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7
Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Overhead Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13
Truck-Manuals.net
Instruments
Instrumentation Control Unit • "Driver Message Center"

Figure 3.1 shows a typical ICU3 instrument cluster.
The instrumentation control unit (ICU) provides the
driver with engine and vehicle information. It is com-
prised of standard and optional gauges, an audible
Ignition Sequence
warning, a driver message center, and a lightbar con- When the ignition is turned on, the ICU runs a self-
taining warning and indicator lamps (also known as check. See Fig. 3.2. Observing the ignition sequence
telltales). Warning and indicator lamps illuminate in is a good way to ensure the ICU is functioning
red (danger), amber (caution), green (status advi- properly.
sory), or blue (high-beam headlights active).
IMPORTANT: Do not crank the engine until the
The following headings in this chapter provide addi- ICU self-check is complete.
tional information and operating instructions for ICU
components: When the ignition is turned on, the following actions
should occur:
• "Warning and Indicator Lights"
• "Instruments"
2 3 4 5
12
11 10 9
09/10/2009 f610525a
NOTE: This instrument cluster is shown with the U.S. speedometer, which shows miles per hour (mph) more prominently
than kilometers per hour (km/h).
1. Engine Oil Pressure Gauge 5. Fuel/DEF Level Gauge 9. Speedometer (U.S. version)
2. Lightbar 6. Primary Air Pressure Gauge 10. Tachometer
3. Driver Message Center 7. Mode/Reset Button 11. Transmission Temperature Gauge
4. Headlight High-Beam Indicator 8. Secondary Air Pressure Gauge 12. Coolant Temperature Gauge
Fig. 3.1, Typical Gauge Layout, U.S. (EPA10 and newer shown)
3.1
Truck-Manuals.net
Instruments
If the ICU receives active fault codes, it displays

IGNITION SWITCH
TURNED TO ON them one after the other until the parking brake is
released or the ignition is turned off. Once the park-
ing brake is completely released, the ICU displays
the odometer. If there are no active faults, the ICU
displays the odometer after the self-check completes.
ICU PERFORMS NOTE: If active faults are present, take the ve-
SELF−TEST
hicle to an authorized Freightliner service facility
as soon as possible.
IF NO FAULTS IF FAULT DETECTED
WERE DETECTED
Audible Alerts
APU 190
123456.7 An audible alert sounds during the ignition sequence
MI
12.3 VOLTS and whenever one of the following conditions exists:
• Engine oil pressure falls below the minimum
PARKING BRAKE PARKING BRAKE
RELEASED RELEASED
preset value.
123456.7 • Coolant temperature rises above the maximum
MI preset value.
12.3 VOLTS
01/18/2012 f040420c • Air pressure falls below about 70 psi (483
kPa).
Fig. 3.2, Ignition Sequence
• Parking brake is set with the vehicle moving
• electronic gauges complete a full sweep of faster than two miles per hour.
their dials
• System voltage falls below 12 volts.
• some warning and indicator lamps illuminate,
• Door is open with the headlights on and the
then are extinguished
parking brake off.
• audible alert sounds until sufficient air pressure
• Driver seat belt is not fastened with the parking
builds up in the primary and secondary air sys-
tems brake off (optional).
• Outside temperature falls below 35°F (1.7°C)
• DEF level indicator illuminates all segments
(optional).
green, then turns them off one at a time before
turning the leftmost segment amber, then red
• software revision level of the ICU is displayed
Warning and Indicator Lights
on the driver message center, followed by ac- There can be up to 28 telltales installed in the ICU. If
tive faults an optional lamp is not requested, the position is
blank.
NOTE: Air gauges do not complete a sweep of
their dials during the ignition sequence. See Table 3.1 for a list of standard and commonly
used warning and indicator lamps.
IMPORTANT: If any red or amber warning and
indicator lamps, or telltales, do not illuminate Warning and indicator lamps illuminate in red (dan-
during the ICU self-check, take the vehicle to an ger), amber (caution), green (status advisory), or
authorized Freightliner service facility as soon blue (high-beam headlights active).
as possible. If any of the red or amber telltales IMPORTANT: Depending upon local jurisdic-
or do not go out after the self-check completes, tional emissions guidelines, vehicles and/or en-
use Table 3.1 to determine if the lamp illumi- gines that are domiciled outside of the U.S. and
nated indicates a problem requiring service. Canada may not be compliant with EPA07,
EPA10, or GHG14 regulations. Noncompliant
3.2
Truck-Manuals.net
Instruments
vehicles may not be equipped with all of the

lamps shown in Table 3.1.
Common Warning and Indicator Lamps

Lamp Description Color
Indicates a serious fault that requires engine shutdown
immediately. The engine protection system will reduce the
maximum engine torque and speed, and, if the condition
does not improve, will shut down the engine within 30 to 60
seconds.
STOP STOP Engine * Safely bring the vehicle to a stop on the side of the road
and shut down the engine as soon as the red light is seen.
If the engine shuts down while the vehicle is in a
hazardous location, turn the key to the OFF position for
a few seconds, then restart the engine and move the
vehicle to a safer location.
Indicates the coolant temperature is above the maximum

High Coolant Temperature
allowable temperature.
Indicates air pressure in the primary or secondary reservoir

Low Air Pressure (EPA07)
has dropped below approximately 70 psi (483 kPa).
Low Air Pressure (EPA10 Indicates air pressure in the primary or secondary reservoir
and Newer) has dropped below approximately 70 psi (483 kPa). Red
Indicates the engine oil pressure is below the minimum

Low Engine Oil Pressure
allowable pressure.
Indicates the parking brake is engaged, or hydraulic brake

Parking Brake (EPA07) fluid level is low. An audible alert activates when the vehicle
BRAKE
is moving over 2 mph (3 km/h) with the parking brake set.
Parking Brake (EPA10

Indicates the parking brake is engaged.
and Newer)
Low Battery Voltage Indicates that battery voltage is 11.9 volts or less.
Activates with an audible alert when the system detects that

the parking brake is off and the driver seat belt is not
Unfastened Seat Belt fastened on some vehicles. On other vehicles, this lamp
illuminates for 15 seconds when the ignition is first turned
on.
Indicates an engine condition (low oil pressure, low coolant
level, high coolant temperature, high DPF soot level, or
CHECK CHECK Engine* uncontrolled DPF regeneration) that requires correction. Amber
Correct the condition as soon as possible. If the condition
worsens, the STOP engine lamp will illuminate.
3.3
Truck-Manuals.net
Instruments

Slow (10-second) flashing indicates a regeneration (regen)
is in progress.
High Exhaust System IMPORTANT: When the HEST lamp is illuminated, do
Temperature (HEST)8* not park the vehicle near flammable material.
Solid illumination indicates high exhaust temperatures at the
outlet of the tail pipe when speed is below 5 mph (8 km/h).
Solid illumination indicates a regen is required. Change to a
more challenging duty cycle (such as highway driving ) to
Diesel Particulate Filter raise exhaust temperatures for at least twenty minutes, or
(DPF) Status perform a parked regen.
Blinking indicates that a parked regen is required
immediately. An engine derate and shutdown will occur.
Malfunction Indicator Indicates an emissions-related fault. See the engine

Lamp (MIL) operation manual for details.
Momentary illumination indicates the vehicle ABS is

engaged.
Vehicle ABS Solid illumination indicates a problem with the vehicle ABS.
Repair the ABS immediately to ensure full braking
capability.
Momentary illumination indicates the trailer ABS is engaged.
Amber
Trailer ABS Solid illumination indicates a problem with the trailer ABS.
Repair the ABS immediately to ensure full braking
capability.
NO Indicates the alternator is not properly powering the

CHARGE No Charge
electrical system.
Indicates the fuel may contain water. Drain any water

Water in Fuel
collected in the fuel/water separators.
Fuel Filter Restriction Indicates the fuel filter is clogged and requires service.
IDLE
MGMT Optimized Idle Indicates optimized idle is enabled.
Check Transmission Indicates an undesirable transmission condition.
Transmission Overheat Indicates high transmission temperature.
3.4
Truck-Manuals.net
Instruments

EPA10 Detroit engines: Indicates that the system is
preventing the starter from cranking. This can occur when
the ignition switch is turned to START before the gauge
sweep has completed, or if the starter has overheated.
WAIT Wait To Start (EPA07/
TO START EPA10) Cummins/Mercedes-Benz engines: Indicates that the intake
warmer is active.
Turn the ignition switch back to ON, wait for the lamp to go
out, then turn the ignition switch to START again.
Indicates that the system is preventing the starter from
cranking. This can occur when the ignition switch is turned
to START before the gauge sweep has completed, or if the
starter has overheated.
START Start Blocked (GHG14
BLOCKED Detroit engines) NOTE: Illumination of the Start Blocked lamp does not
indicate a problem with the starter.
Turn the ignition switch back to ON, wait for the lamp to go Amber
out, then turn the ignition switch to START again.
Flashing indicates the ATC system is active, or the ATC
button has been pressed to allow wheel slip.
WHEEL
SPIN Wheel Spin Solid illumination indicates a problem with the ATC system.
Repair the ATC system immediately to ensure full braking
capability.
Momentary illumination indicates that a stability event has
occurred.
Roll Stability On vehicles that are also equipped with ATC, flashing
indicates the ATC button has been pressed to allow wheel
slip.
Hill Start Aid (HSA) Indicates the HSA switch has been pressed to override the
Override hill start assist feature.
Engine Brake Indicates the engine brake is enabled.
Flashing indicates the outside left-turn signal lights are

Left-Turn Signal
activated.
Green
Flashing indicates the outside right-turn signal lights are
Right-Turn Signal
activated.
Indicates the cruise control is enabled.

Cruise Control NOTE: The ICU4Me does not have a green cruise control
telltale.
3.5
Truck-Manuals.net
Instruments

High-Beam Headlights Indicates the high-beam headlights are on. Blue
* See Fig. 3.3 for an explanation of the aftertreatment system (ATS) warning indicators, and actions required to avoid further engine protection steps.
Table 3.1, Common Warning and Indicator Lamps
Engine Protection System The STOP engine lamp illuminates when the engine
protection system is activated in one of two ways. On
some engines, the engine protection system will der-
WARNING ate the engine, allowing it to run at lower rpm and
slower vehicle speed. Drive the vehicle to a safe lo-
When the red STOP engine lamp illuminates, cation or to a service facility.
most engines are programmed to shut down au-
tomatically within 30 seconds. The driver must IMPORTANT: Safely bring the vehicle to a stop
immediately move the vehicle to a safe location on the side of the road and shut down the en-
at the side of the road to prevent causing a haz- gine as soon as the red light is seen. If the en-
ardous situation that could cause bodily injury, gine shuts down while the vehicle is in a haz-
property damage, or severe damage to the en- ardous location, turn the key to the OFF position
gine. for a few seconds, then restart the engine and
See Fig. 3.3 for an explanation of the aftertreatment move the vehicle to a safer location.
system (ATS) warning indicators, and actions re-
quired to avoid further engine protection steps.

INDICATOR WARNING
CHECK STOP
LAMP(S)
(Solid) (Flashing) (Flashing)
Indicator Lamp Filter Regeneration Filter Parked Regeneration Service Regeneration Required. HEST (High Exhaust
Message(s) Recommended. Regeneration Required − Engine Engine Derate To Idle Only. System Temperature)
Necessary Derate
Diesel Particulate Filter is reaching Filter is now Filter has reached Filter has exceeded maximum Flashing
Filter Condition capacity. reaching maximum maximum capacity. capacity. A regeneration is in
Switch.
capacity. progress.
Required Action Bring vehicle to To avoid engine Vehicle must be Vehicle must be parked, and a
highway speeds to derate, bring vehicle parked, and a Parked Service Regeneration must be Solid
allow for an to highway speeds Regeneration must performed. Check engine Exhaust components
Automatic to allow for an be performed. operator’s manual for details. and exhaust gas are at
Regeneration or Automatic Engine will begin Engine will shut down. high temperature. When
perform a Parked Regeneration, or derate. stationary, keep away
Regeneration. perform a Parked from people and
Regeneration as flammable materials or
soon as possible. vapors.
02/20/2009 f080156
Fig. 3.3, ATS Warning Lamps
3.6
Truck-Manuals.net
Instruments
On other engines, the engine protection system will i. Odometer

shut down the engine. It will first derate the engine,
ii. Trip distance
then shut it down completely 30 to 60 seconds after
the indicator illuminates (depending on the critical iii. Trip hours
fault type) if the condition does not improve. Bring
the vehicle to a stop on the side of the road before iv. Outside temperature
the engine shuts down. v. Select units
Some vehicles may have a shutdown-override vi. Temperature alert
switch, which may be used to momentarily override
the shutdown sequence. See Chapter 7 for detailed vii. Diagnostics
information regarding the shutdown process. viii. Engine miles
IMPORTANT: Do not attempt to restart the en- ix. Engine hours
gine while the vehicle is moving. Bring the ve-
hicle to a safe stop, then restart the engine. x. Setup
To restart the engine, turn the ignition to OFF, leave Temperature Alert
it there a few seconds, then turn the ignition to
START. The engine will run for a short period and When the outside temperature drops to 34°F (1.7°C)
shut down again if the condition does not improve. or less, the ICU displays a caution text at one-
second intervals for five seconds, and an audible
alert sounds. Tap the mode/reset switch to acknowl-
Driver Message Center edge the message. The audible alert will not sound
The driver message center is controlled using the again unless the temperature cycles above 37°F
mode/reset switch, located on the right side of the (4°C) and back to 34°F (1.7°C) or less. This warning
ICU. See Fig. 3.1. Tap the mode/reset switch to ad- only occurs while the ignition is on and the parking
vance one screen; press and hold the switch to se- brake is released.
lect a menu choice or reset the display. When the The temperature alert message allows the driver to
display resets, an audible chirp sounds. enable or disable the ambient temperature warning.
Driving Screens Press and hold the mode/reset switch to toggle be-
tween on and off. Release the mode/reset switch,
The following screens are available when the parking then tap it to select the displayed choice.
brake is off (when the vehicle is mobile) and no ac-
tive fault codes are found. Use the mode/reset switch Diagnostics
to scroll through the screens. To reset any values,
When the DIAG screen is displayed, press and hold
press and hold the mode/reset switch. The driving
the mode/reset switch to access the various diagnos-
screens appear in the following order:
tic screens.
i. Odometer
The diagnostic screens are used by trained techni-
ii. Trip distance cians to retrieve fault codes and other diagnostic in-
formation pertaining to the vehicle. If active fault
iii. Trip hours
codes display during start-up or at any other time,
iv. Outside temperature make a note of the fault code and take the vehicle to
an authorized Freightliner service facility
Parked Screens/Menus If fault codes are displayed, press and hold the
The parked screens and menus are available when mode/reset switch to view the next fault code until
the parking brake is on and no active fault codes are reaching the DIAG screen.
found. See Fig. 3.4. Use the mode/reset switch to
scroll through the parked screens. To reset any val-
ues, press and hold the mode/reset switch. The
parked screens appear in the following order:
3.7
Truck-Manuals.net
Instruments
123456.7
Default Odometer CLEAr
MI Hold Clear Defaults
12.3 VOLTS Dispay Screen
Push Push
123456.7 123456.7
TRIP MI Hold MI To Dispay Total Engine Miles
To Reset Trip Miles
12.3 VOLTS ENGINE
Push Push
123456.7 123456.7
TRIP HOURS Hold HOURS To Dispay Total Engine Hours
To Reset Trip Hours
12.3 VOLTS ENGINE
Push Push
SELECt To Toggle between Units EnG oIL

Hold Hold Dispay Oil Level
MI MI<−−−−>KM *Lo
*Lo = Oil Level Low
HI = Oil Level High
Push Push Blank = Oil Level OK
− − = No Message
dIAG SEtUP
MI HOURS Hold **MI **HOURS Hold Dispay Service Interval
Dispay Diagnostics
n **no Cycle Screens
n = Number of Active Fault Codes **MI = CYCLE Miles Active Mode
MI = CYCLE Miles Enabled **HOURS = CYCLE Hours Active Mode
Push HOURS = Cycle Hours Enabled Push **no = Service CYCLE Inactive
08/29/2012 f040636b
NOTE: The engine oil level screen displays for Mercedes-Benz engines only (if equipped and enabled).
Fig. 3.4, ICU3 Stationary Screens
Engine Miles/Hours The last screen in the setup menu, RESET EE, is for
resetting certain parameters to the original settings.
When the engine miles/hours screen is displayed, Press and hold the mode/reset switch to reset the
press and hold the mode/reset switch to access the antilock braking system (ABS), SAMs roll call, auto-
engines screen submenu. mated transmission display, transmission heartbeat,
sensor fault codes, seat belt switch learning, and en-
Setup gine oil level.
The setup menu allows the driver to manage ICU
parameters. The setup screen submenu allows the Instruments
driver to enable and change service intervals.
Standard instruments are present on every vehicle.
If service intervals are enabled and service distance They are listed here in alphabetical order to make
or time has been exceeded, the text SERVICE the information easier to find.
HOUR/MI (KM) will display at start-up to indicate ve-
hicle service is required. Optional instruments, typically located on the auxil-
iary dash panel or right-hand control panel, are not
For each parameter, press and hold the mode/reset found on every vehicle. They are listed here in alpha-
switch to navigate to the parameter change screen. betical order, to make the information easier to find.
In each change screen, tap the mode/reset switch to
toggle between options.
3.8
Truck-Manuals.net
Instruments
Air Intake Restriction Gauge Air Intake Maximum Restriction Values (inH2O)
Pre-EPA07 EPA07 and
The air intake restriction gauge indicates the vacuum Engine
Engines Newer Engines
on the engine side of the air cleaner. On standard
Detroit™ 20 22
installations, it is mounted on the air intake duct in
the engine compartment. As an option for easier Mercedes-Benz 22 22
viewing, the air intake restriction indicator (see Table 3.2, Air Cleaner Element Maximum Restriction
Fig. 3.5) can be mounted on the dash, usually on the
right-hand control panel.
04/08/2005 f090431
Fig. 3.6, Manual-Reset Air Restriction Indicator, Go/

No-Go
Ambient Temperature Gauge

The ambient temperature gauge, shown in Fig. 3.7,
10/10/2001 f610568 displays the in-cab or outside temperature, depend-
ing on the settings selected.
Fig. 3.5, Air Intake Restriction Indicator
NOTE: Rain or snow can wet the filter and

cause a temporary high reading.
Air intake restriction vacuum is measured in inches
of water (inH2O). For vehicles equipped with a
graduated indicator or a restriction gauge on the
dash, check the gauge with the engine off. If the yel-
low signal stays locked in the red zone once the en-
gine is shut down, or is at or above the values
shown in Table 3.2, the air cleaner element needs to
SET ADJ ALARM
be replaced.
Vehicles may be equipped with a go/no-go restriction IN OUT
indicator without graduations (see Fig. 3.6) instead of
a graduated indicator.
12/14/2011 f611153
Air Intake Maximum Restriction Values (inH2O)
Pre-EPA07 EPA07 and Fig. 3.7, Ambient Temperature Gauge
Engine
When the alarm is enabled, the ambient temperature
Caterpillar 25 —
gauge will sound an audible alert and the amber
Cummins 25 25
3.9
Truck-Manuals.net
Instruments
lamp will illuminate when the outside or inside tem- If coolant temperature rises above the maximum
perature (depending on the setting selected) reaches temperature listed in Table 3.3, the CHECK engine
the set temperature. Turn the alarm on and off using lamp will illuminate. If the condition does not im-
the steps below. prove, the STOP engine lamp will also illuminate and
an audible warning will sound. The engine will then
1. Press the IN button for in-cab temperature, or
derate or shut down, depending on the type of en-
the OUT button for outside temperature.
gine protection system installed.
2. Press the SET button.
Maximum Coolant Temperature
3. Press the ADJ button until the desired tempera-
Engine Make Temperature: °F (°C)
ture is displayed.
Caterpillar 230 (110)
4. Press the ALARM button and "AL" will appear on Cummins 225 (107)
the display. Detroit 215 (101)
5. Press the SET button to return to the current Mercedes-Benz 222 (105)
temperature display. Table 3.3, Maximum Coolant Temperature
NOTE: To turn the alarm off, press the ALARM
button again and "AL" will disappear from the
display.
Engine Oil Pressure Gauge
Coolant Temperature Gauge NOTICE

A sudden decrease or absence of oil pressure
NOTICE may indicate mechanical failure. Bring the vehicle
to a safe stop and investigate the cause to pre-
A sudden increase in coolant temperature may vent further damage. Do not operate the engine
indicate engine or cooling system failure. Bring until the cause has been determined and cor-
the vehicle to a safe stop and investigate the rected.
cause to prevent further damage. Do not operate
the engine until the cause has been determined The engine oil pressure gauge, as shown in Fig. 3.9,
and corrected. displays the current engine oil pressure. If engine oil
pressure falls below the minimum levels shown in
During normal engine operation, the coolant tem- Table 3.4, the CHECK engine lamp will illuminate. If
perature gauge, as shown in Fig. 3.8, should read the condition does not improve, the STOP engine
175 to 195°F (79 to 91°C). If the temperature re- lamp will also illuminate and an audible warning will
mains below 160°F (71°C), inspect the cooling sys- sound. The engine will then derate or shut down, de-
tem to determine the cause. pending on the type of engine protection system
installed.
Minimum Oil Pressure*

At Idle Speed: At Rated RPM:
Engine Model
150 200 psi (kPa) psi (kPa)
Caterpillar 10–20 (69–138) 30–45 (207–310)
F° Cummins 15 (103) 35 (241)
Detroit 14 (97) 55 (350)
100 250 Mercedes-Benz 7 (50) 36 (250)
* Oil pressures are given with the engine at operating temperature. With
WATER the engine cold, oil pressure may be higher. Individual engines may vary
from the listed pressures; observe and record pressures when the engine
10/09/2001 f610565 is new to create a guide for checking engine condition.
Table 3.4, Minimum Oil Pressure
Fig. 3.8, Coolant Temperature Gauge
3.10
Truck-Manuals.net
Instruments
50
PSI
0 100
OIL
10/09/2001 f610528
Fig. 3.9, Engine Oil Pressure Gauge 10/10/2001 f610569
Engine Oil Temperature Gauge Fig. 3.10, Engine Oil Temperature Gauge
NOTICE
A sudden increase in oil temperature that is not 1/2
caused by a load increase may indicate mechani-
cal failure. Bring the vehicle to a safe stop and
investigate the cause to prevent further damage.
Do not operate the engine until the cause has
been determined and corrected.
E F
During normal operation, the optional engine oil tem-
perature gauge (Fig. 3.10) should read in the follow- FUEL
ing temperature ranges:
10/09/2001 f610566
• 160 to 195°F (71 to 91°C) for Caterpillar en-
gines Fig. 3.11, Fuel Level Gauge, Pre-EPA10
• 200 to 260°F (93 to 126°C) for Detroit and Fuel/Diesel Exhaust Fluid (DEF)
Cummins engines
Gauge, EPA10 and Newer
• 177 to 203°F (81 to 95°C) for Mercedes-Benz
engines For engines that are EPA10-compliant or newer, the
fuel and DEF levels are measured in a dual purpose
Under heavy loads, such as when climbing steep fuel/DEF level gauge. See Fig. 3.12.
grades, temperatures that exceed the normal oil tem-
perature range for a short period are not unusual. If The diesel fuel level is indicated at the top of the
the temperature returns to normal when the load de- gauge, with a low-fuel warning lamp that illuminates
creases, there is no problem. when the diesel fuel level registers 1/8th of capacity.
The DEF level is indicated in the lightbar on the
Fuel Gauge, Pre-EPA10 lower portion of the gauge. There is a low DEF level
warning lamp that illuminates amber when the DEF
The fuel gauge indicates the level of fuel in the fuel
level reaches 10% of capacity. See Chapter 7 for
tank(s). A single fuel gauge is standard. If equipped
details of the DEF gauge functions.
with an optional second fuel tank, each fuel tank
level is indicated on a separate gauge. See
Fig. 3.11.
3.11
Truck-Manuals.net
Instruments
1/2
ULTRA LOW SULFUR
DIESEL FUEL ONLY
4 E F
DEF
E F 05/14/2001 f610556
3 Fig. 3.13, Air Pressure Gauge (reservoir A shown)

2
08/21/2009 f611045
Speedometer
1. Diesel Fuel Level Indicator
2. DEF Level Indicator Three speedometer options are available. The U.S.
3. Low DEF Warning Lamp (amber below 10% DEF) version of the speedometer registers speed in both
4. Low Fuel Warning Lamp (amber at 1/8 tank of fuel) miles per hour (mph) and kilometers per hour (km/h),
with mph in larger numbers. The metric version of
Fig. 3.12, Fuel/DEF Gauge, EPA10
the speedometer face reverses this arrangement,
with km/h in larger numbers. The metric-only version
Primary and Secondary Air Pressure shows km/h exclusively.
Gauges
Tachometer
WARNING The tachometer indicates engine speed in revolutions
per minute (rpm) and serves as a guide for shifting
If air pressure falls below minimum pressure, the the transmission and keeping the engine in the ap-
braking ability of the vehicle will be limited. Slow propriate rpm range. For low idle and rated rpm, see
the vehicle down and bring it to a gradual stop. the engine identification plate.
Do not attempt to move the vehicle until air pres-
sure has risen above the minimum level. Moving Transmission Fluid Temperature
a vehicle without adequate braking power could
cause an accident resulting in property damage, Gauge
personal injury, or death. The transmission fluid temperature gauge, shown in
Air pressure gauges, as shown in Fig. 3.13, register Fig. 3.14, measures the transmission lubricant oper-
the pressure in the primary and secondary air sys- ating temperature. Temperatures vary by application,
tems. The gauges are labeled for the A or B reser- but the transmission fluid temperature gauge reading
voir. Normal pressure with the engine running is 100 should not exceed 250°F (121°C).
to 120 psi (689 to 827 kPa) in both systems.
A low-air-pressure warning light and audible alert, NOTICE
connected to both the primary and secondary sys-
tems, activate when air pressure in either system A sudden increase in transmission fluid tempera-
drops below approximately 70 psi (483 kPa). ture that is not caused by a load increase may
indicate mechanical failure. Bring the vehicle to a
When the engine is started, the warning light and safe stop and investigate the cause to prevent
audible warning remain on until air pressure in both further damage. Do not operate the vehicle until
systems exceeds minimum pressure. the cause has been determined and corrected.
3.12
Truck-Manuals.net
Instruments
gine is off, the voltmeter shows only the isolated bat-

tery voltage and does not indicate the voltage of the
engine-starting batteries.
200 275 Overhead Instrument Panel

F The optional overhead instrument panel, shown in
Fig. 3.15, may hold a citizen’s band (C/B) radio, a
125 350 microphone clip, and any switches that can not be
accommodated on the driver’s or auxiliary dash
TRANS panels.
10/30/2001 f610600 The underside of the overhead console also holds
the sun visors and the optional dome/reading light
Fig. 3.14, Transmission Fluid Temperature Gauge assembly. For more information on the dome/reading
light assembly, see Chapter 4.
Under heavy loads, such as when climbing steep
grades, temperatures that exceed the normal oil tem-
perature range for a short period are not unusual. If
the temperature returns to normal when the load de-
creases, there is no problem.
Turbocharger Boost Pressure Gauge

A turbocharger boost pressure gauge indicates the
pressure in the intake manifold, in excess of atmos-
pheric pressure, being created by the turbocharger.
Voltmeter
The voltmeter indicates the vehicle charging system
voltage when the engine is running and the battery
voltage when the engine is off. By monitoring the
voltmeter, the driver can stay aware of potential bat-
tery charging problems and have them fixed before
the batteries discharge enough to create starting diffi-
culties. Cascadia vehicles are equipped with either a
voltmeter gauge, or a digital voltmeter readout lo-
cated on the bottom line of the dash message center.
The voltmeter will normally show approximately 13.7
to 14.1 volts when the engine is running. The voltage
of a fully charged battery is 12.7 to 12.8 volts when
the engine is off. Battery voltage under 12.0 volts is
considered a low battery, and a completely dis-
charged battery will produce only about 11.0 volts.
If the voltmeter shows an undercharged or over-
charged condition for an extended period, have the
charging system and batteries checked at an autho-
rized Freightliner service facility.
On a vehicle equipped with a battery isolator system,
the voltmeter measures the average voltage of all the
batteries when the engine is running. When the en-
3.13
Truck-Manuals.net
Instruments
1 2 3 4
04/19/2002 f680028
1. Storage Area with Netting 3. Microphone Clip
2. C/B Radio 4. Dome/Reading Light Assembly
Fig. 3.15, Overhead Instrument Panel
3.14
Truck-Manuals.net
4
Controls
Ignition Switch and Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Lighting Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Multifunction Turn Signal Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5
Horn Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Powertrain Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
All-Wheel-Drive Controls, Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Adjustable Steering Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Other Dash-Mounted Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.14
Heater/Air Conditioner Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
Seat Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
Truck-Manuals.net
Controls
Ignition Switch and Key WARNING

The ignition switch (Fig. 4.1) has four positions: AC-
CESSORY, OFF, ON, and START. In addition, the Do not attempt to modify, add, splice, or remove
same key locks and unlocks the cab doors. electrical wiring on this vehicle without authoriza-
tion from Freightliner Engineering. Doing so
could damage the electrical system and result in
a fire that could cause serious personal injury or
property damage.
There are two new electrical modules, a master mod-
ule located near the frontwall (bulkhead module) and
a slave module located between the frame rails
(chassis module).
This new wiring system features intelligent controls
that blink to show switch activity and error conditions.
These controls cannot be distinguished by their ap-
pearance, only by their function.
09/12/2001 f610509 For more information about these controls, see under
the headings "Axle Switches" and "Suspension
Fig. 4.1, Ignition Switch Positions Dump Switch."
In the OFF position, the key slot is vertical; the key
can be inserted and removed only in this position. Lighting Controls
The following can be operated in the off position (re- The lighting controls mentioned under this heading
gardless of whether the key is inserted): The low- generally operate through switches located on the
beam headlights, taillights, brake lights, road lights, dash.
dome lights, clearance lights, turn signals, hazard
warning lights, horn, CB radio, power windows, ciga- Two types of dash switches are used:
rette lighter, clock, and electric oil pan heater. • Paddle switches with a single paddle located in
In the ACCESSORY position, the key is turned coun- the center of the switch. The paddle can be
terclockwise. The radio, stereo system, mirror heat, raised or lowered to perform a function.
air dryer, backup lights, and all of the electrical sys- • Rocker switches that can be pressed at either
tems that are operable in the off position are oper-
the upper or lower end to perform a function.
able in the accessory position.
Certain rocker switches are guarded to prevent
In the ON position, the key is turned clockwise and them from being switched on or off acciden-
all electrical systems are operable. The low air pres- tally.
sure and low oil pressure warning lights (or mes-
When the panel lights are on, most switch legends
sages) and buzzer operate until the engine is started
are backlit with a colored light, usually green. This
and pressure is built up.
allows the driver to find the switch more easily in the
dark. When the switch is on, the switch icon is nor-
Electrical System mally backlit with a colored light, usually amber.
Some switch icons are dead-fronted (not visible until
The Business Class® M2 features a new type of the switch is turned on). When turned on, some
electrical system, different from any previous vehicle. switches are illuminated from within by a red or
Multiple electrical signals are carried along a simpli- amber LED (light-emitting diode).
fied set of wires, reducing the size of wiring bundles.
There are significantly fewer wires overall, meaning
less chance of damage, shorts and other problems.
Control Panels
The left-hand control panel (Fig. 4.2) contains a lou-
vered window outlet for the face vents of the heating,
4.1
Truck-Manuals.net
Controls
ventilation, and air conditioning system (HVAC), and The HVAC climate control panel is on a separate
four switches arranged in a vertical line, usually the panel below the auxiliary dash panel, between the
headlight, panel light increase/decrease, and the two cupholders.
cruise control On/Off and Set/Resume switches.
Exterior Light Controls
Headlight/Parking Light Switch
2
The headlight/parking light switch (Fig. 4.3) is a
3 paddle switch located on the left-hand control panel
above the cruise control switches. When the paddle
is lowered, the parking lights illuminate (the front turn
signals, the cab marker and identification lights, and
4 the taillights). When the paddle is raised, the low-
beam headlights illuminate, along with all the parking
1 lights. To turn off all lights, return the paddle to the
center position.
10/15/2001 f610579a
1. Left-Hand Control Panel

2. Instrumentation Control Unit
3. Right-Hand Control Panel
4. Radio Panel
5. Auxiliary Dash Panel 10/15/2001 f610580
Fig. 4.2, Switch and Gauge Panels Raise the paddle to illuminate the headlights, low beam.
The instrument cluster (ICU3-M2) is located right be- Lower the paddle to illuminate the parking lights.
hind the steering wheel. No controls are installed on Fig. 4.3, Headlight/Parking Light Switch
the standard instrument cluster.
NOTE: The front turn signal is the amber lens in
The right-hand control panel (Fig. 4.2) usually con-
tains the transmission push-button shift selector (on each headlight unit. The low-beam headlight is
vehicles with automatic or automated transmission) the top clear lens in each headlight unit.
and the trailer brake lever (hand control valve). On When the headlights or parking lights are on, the
vehicles with manual transmission, a variety of panel lights also illuminate. An amber light in the
switches are installed here. If there is a dash- switch backlights either the top icon (for headlights
mounted air-restriction indicator, it is often mounted and parking lights) or the bottom icon (for parking
here. lights only).
The radio panel contains two louvered dash outlets
for the face vents of the HVAC, one on either side of Panel Light Increase/Decrease Switch
the radio (if installed). When the panel lights are on, they can be either
The auxiliary dash panel (Fig. 4.2) below the radio brightened or dimmed by using the INCR/DECR
panel contains the marker interrupt switch, the air rocker switch just below the headlight switch
brake valve knobs, the cigarette lighter, and a variety (Fig. 4.4). To brighten the panel lights, press on the
of switch options. upper part of the rocker (at the INCR legend). To dim
4.2
Truck-Manuals.net
Controls
the panel lights, press on the lower part of the rocker

(at the DECR legend).
05/09/2002 f610581
Raise the paddle to flash the marker lights.

10/29/2001 f610598 Fig. 4.5, Marker Light Interrupt Switch
Fig. 4.4, Panel Light Increase/Decrease Switch The low beam headlights must be turned on before
the road lights can be turned on. The road lights will
When the panel lights are on, both legends are back- not illuminate if the high beam headlights are already
lit in green. on, and switching from low beams to high beams will
switch off the road lights.
Daytime Running Lights
To turn the road lights on, press on the upper part of
Switching on the ignition and releasing the parking the rocker (at the road light icon). See Fig. 4.6. To
brakes automatically activates the daytime running turn the road lights off, press on the lower part of the
lights, if equipped. The daytime running lights will rocker (at the ROAD LAMP legend).
operate until the parking brakes are applied or the
headlights are turned on.
NOTE: Daytime running lights are standard on
all Canadian vehicles.
The daytime running lights illuminate at about two-
thirds of normal power.
Marker Light Interrupt Switch

The marker light interrupt (MRKR INT) paddle switch
temporarily flashes the marker lights and taillights
(Fig. 4.5). With the vehicle lights on, raise the paddle
10/15/2001 f610582
to briefly turn off the marker lights and taillights. With
the vehicle lights off, raise the paddle to briefly turn
Fig. 4.6, Road Light Switch
on the marker lights and taillights.
Turning off the vehicle lights automatically turns off When the road lights are on, the road light icon is
the marker lights. When the panel lights are on, the backlit in amber. When the panel lights are on, the
marker light icon and MRKR INT legend are backlit ROAD LAMP legend is backlit in green.
in green.
Utility Light Switch, Optional
Road Light Switch, Optional The utility light switch operates one of the following
The road light (ROAD LAMP) rocker switch operates lights or sets of lights:
the optional road lights, which are recessed into the • A single round utility light swivel-mounted in
front bumper or mounted on the lower edge of a cut- the center of the cab roof;
out in the center of the front bumper.
4.3
Truck-Manuals.net
Controls
• Two round utility lights mounted in fixed posi-

tions on each side of the cab roof;
• Two flush-mounted utility lights mounted on the
back of the cab, one on each side.
To turn the utility light(s) on, press in on the upper
part of the utility light (UTLY LAMP) rocker switch
(Fig. 4.7). To turn the utility light(s) off, press on the
lower part of the rocker (at the UTLY LAMP legend).
10/16/2001 f543926
To remove the lens, press in at the mounting tabs
(arrows).
Fig. 4.8, Rear Dome Light
1
10/15/2001 f610583
2
Fig. 4.7, Utility Light Switch
When the utility lights are on, the diagonal light beam
icon is backlit in red. When the panel lights are on,
the UTLY LAMP legend is backlit in green.
Spotlight, Optional 3
The spotlight switch is located on the pivoting handle 10/17/2001 f610587

of the spotlight. There may be a single spotlight as-
1. Overhead Console 3. Light Assembly
sembly mounted on the driver’s door, or one on each
2. Trimplate
door.
Fig. 4.9, Overhead Console Dome Lights
Interior Lights and Light Controls
Light Replacement
The interior lights include dome lights, red map
lights, and clear reading lights. Rear Dome Light
To replace the rear dome light (Fig. 4.8), do the fol-
Dome Lights lowing steps:
Diffuse dome lights are installed on all cabs. The 1. Press in on the lens at the four mounting tabs
standard dome light has a clear lens and is installed (arrows).
on the back of the cab above the rear window. See
Fig. 4.8 for the rear dome light. 2. Replace the bullet-type bulb and install the lens
on the lamp base with the button at the bottom.
On cabs with an overhead console, there is an op-
tional overhead dome light assembly containing a Overhead Console Dome/Reading Lights
diffuse dome and a clear reading light. See Fig. 4.9
for the optional dome/reading lights on the overhead To replace the overhead console dome/reading lights
console. (Fig. 4.9), do the following steps:
4.4
Truck-Manuals.net
Controls
1. Remove the tapping screws that attach the lamp

assembly and trimplate to the overhead console.
4
2. Separate the lamp assembly from the trimplate
and disconnect the wiring harness.
5
3. Replace the lamp assembly.
4. Snap the lamp assembly and trimplate together. 1
5. Connect the lamp assembly to the wiring har- 2
ness.
3
6. Insert the tabs on the trimplate into the slots on
the overhead console attachment plate.
11/16/2001 f820386
7. Center the lamp assembly in the headliner cutout
and install the center tapping screw. Press down on the upper part of the rocker to activate
the hazard warning flashers.
8. Install the remaining tapping screws. 1. Washer Button
2. Wiper Control Dial
Dome Light Switches 3. Turn Signal Lever
4. Hazard Flasher (red rocker switch)
In the standard cab, there is one dome light switch in 5. Multifunction Switch Module
the driver’s door that turns on the diffuse dome light
when the driver’s door is opened. In one option, two Fig. 4.10, Multifunction Turn Signal Switch
switches are installed, so that the diffuse dome light
turns on when either the driver’s or passenger’s door Turn-Signal Controls
is opened.
The turn signal lever (Fig. 4.11) is mounted on the
Clear Reading Lights, Optional steering column. Moving the lever down turns on the
left turn signal lights; moving it up turns on the right
Clear reading lights are available as a option. They turn signal lights.
are included only in the light assembly installed in
the overhead console, located next to the diffuse
dome light in the same fixture (Fig. 4.9). Like the
dome lights, the reading lights are door-activated.
Multifunction Turn Signal

Switch
The multifunction turn signal switch is attached to the
steering column, just below the steering wheel, on
the left-hand side. This switch has the following
functions:
• The turn signals
10/17/2001 f820384
• The windshield wipers and washers
Move the lever down to turn on the left turn signals.
• The headlight high beams Move the lever up to turn on the right turn signals.
• The hazard warning flasher Fig. 4.11, Turn Signal Controls
See Fig. 4.10 for the multifunction switch and its
When one of the turn-signal lights is on, a green indi-
component parts.
cator arrow flashes at the far left or far right of the
warning and indicator light panel.
4.5
Truck-Manuals.net
Controls
The lever automatically returns to the neutral position the control dial clockwise as far as it will go (to the
(self-cancels the switch) when the steering wheel OFF setting) turns the wipers off.
returns to the straight ahead position after a turn. To The washers are operated by a yellow button at the
cancel the signal manually, move the lever to the very end of the turn signal lever. To operate the
neutral position. washers, press the button in and hold it in until you
want the washers to stop.
Windshield Wiper/Washer Controls
Headlight High Beams
CAUTION Push the turn signal lever forward, towards the wind-
Do not move the wiper arms manually. Wiper shield, to turn on the high-beam headlights. Pull the
motor damage will occur if the arms are moved. turn signal lever back to its original position to turn
them off. See Fig. 4.13.
The wipers are operated by a rotary switch in the
wiper control dial, which is on the end of the turn sig-
nal lever. See Fig. 4.12. There are five delay set-
tings, marked on the dial by lines of increasing 1
length, and two steady speed settings, LO and HI.
1 3
4
10/17/2001 f820385
5
Move the lever away from you to turn on the high beams.
Move the lever back to its original position to turn them
10/29/2001 f820383
off.
Rotate the control dial away from you to turn the wipers
on, or speed them up. Move the lever towards you to flash the high beams
momentarily.
Rotate the control dial towards you to slow the wipers
down, or turn them off. 1. Turn Signal Lever 2. Boot
1. Washer Button Fig. 4.13, Headlight High Beams
2. OFF Position
3. Delay Positions When the high beam headlights are on, a blue light
4. Wipers On, Low Speed illuminates on the instrument cluster between the ta-
5. Wipers On, High Speed chometer and speedometer. For vehicles built to op-
Fig. 4.12, Wiper/Washer Controls erate in the United States, switching on the high
beams will switch off the road lights.
Rotating the control dial forward (in a counterclock-
NOTE: The ignition switch must be on for the
wise direction) turns the wipers on. If they are al-
ready on, rotating the handle further forward (to a high beams to work.
faster speed setting) increases the speed of the wip- With the headlight low beams on, pull the lever back-
ers through the various delay settings, and to LO and ward, towards the steering wheel, to flash the high
then HI. beams (turn them on momentarily).
Rotating the control dial in the opposite direction
(clockwise) causes the wipers to slow down. Rotating
4.6
Truck-Manuals.net
Controls
The headlight low beams remain on continuously The air horn is controlled by a wire lanyard hanging
during high beam operation. If the low beam head- down just inboard on the driver’s door. See Fig. 4.15.
lights are turned off by use of the headlight switch, Pull downward on the lanyard to sound the air horn.
the high beams turn off also.
Hazard Warning Flasher

The hazard warning light flasher (Fig. 4.10) is a red
rocker switch located on the top of the multifunction
switch module. When the flashers are activated, all
of the turn signal lights (front, side, and rear) and the
two green indicator arrows on the control panel will
blink on and off.
To flash the hazard warning lights, press down on
the upper part of the rocker (towards the dash). To
stop the hazard warning lights, press down on the
lower part of the rocker (towards the steering wheel). 10/17/2001 f610592
To sound the air horn, pull down on the lanyard (arrow).

Horn Controls Fig. 4.15, Air Horn Control
NOTE: It is possible to have both the electric
and the air horn installed on one vehicle. Powertrain Controls
Electric Horn After-Treatment System (ATS)
A single electric horn is standard. Dual electric horns Request/Inhibit Regen Switch
are available as an option. A parked regen of the ATS can be initiated with the
The button for the electric horn is located in the cen- request/inhibit regen switch. It may also be used to
ter of the steering wheel. To sound the horn, press inhibit the vehicle from performing an automatic
down on the button. See Fig. 4.14. regen. See Fig. 4.16.
The style and function of switch will vary with the en-
gine make and model. See the engine operation
manual for operation details.
10/17/2001 f461918 RGEN

To sound the electric horn, press down on the horn
button.
1. Horn Button 03/09/2012 f610848
Fig. 4.14, Electric Horn Control Fig. 4.16, Request/Inhibit Regen Switch
Air Horn, Optional

Single and dual air horns are available as options.
4.7
Truck-Manuals.net
Controls
Cruise Control Switches

CAUTION
Do not attempt to shift gears without using the
1
clutch pedal when the cruise control is engaged.
Failure to follow this precaution will result in a
temporarily uncontrolled increase in engine
speed; transmission damage and gear stripping
could result.
On standard models, cruise control is activated by
two dash switches. See Fig. 4.17. On some models,
cruise control can be activated by a button on the
transmission shift knob.
• The On/Off Switch—this two-position rocker 2
switch bears the legend SPD CNTL on the
lower half of the switch. When cruise control is
on, an amber light illuminates in the top part of
09/13/2001 f610510
the switch.
To turn cruise control on, press the upper half of the On/
• The Set/Resume Switch—this three-position Off (rocker) switch. To turn cruise control off, press the
paddle switch bears the legend RES/ACC lower half of the On/Off (rocker) switch.
above the paddle and SET/CST below the 1. Cruise Control On/Off (rocker) Switch
paddle. 2. Cruise Control Set/Resume (paddle) Switch
NOTE: For more information about cruise con- Fig. 4.17, Cruise Control Switches, Dash-Mounted
trol operation, see Chapter 7.
Engine Brake Switch, Optional 1 2

The engine brake switch controls the degree of en-
gine braking. Normally there are two paddle
switches, a two-position On/Off Switch to activate the
engine brake, and a two-position HI-LO Switch to
control the amount of engine braking.
To turn the two-position On/Off Switch on, raise the
paddle. When the two-position switch is on, an
amber LED (light-emitting diode) illuminates inside
the switch. 10/17/2001 f610588
To turn the two-position HI-LO Switch on high, raise 1. On/Off Switch 2. HI-LO Switch
the paddle (at the HI-LO icon). To turn the two-
Fig. 4.18, Engine Brake Switches
position HI-LO Switch on low, lower the paddle (at
the ENG BRK legend). See Fig. 4.18. The engine brake turns off automatically or when the
A three-position switch is used on MBE900 engines clutch pedal is pressed. On vehicles without a clutch
equipped with both the regular engine brake and the pedal, the brake pedal can be used to deactivate the
constant-throttle (decompression) brake. It works the engine brake. For more information about engine
same as the two-position HI-LO switch, except that brake operation, see Chapter 7.
there is a third (off) position when the switch is left at When the panel lights are on, the HI-LO icon is back-
its normal position. lit in amber on the HI-LO switch. On both switches,
4.8
Truck-Manuals.net
Controls
the ENG BRK legend is backlit in green when the Engine Fan Switch, Optional
panel lights are on.
The engine cooling fan can be turned on by the en-
Exhaust Brake Switch, Optional gine fan switch (ENG FAN legend). The fan will con-
tinue to operate for a set amount of time and then
The optional exhaust brake is controlled by a dash- turn off unless the coolant temperature is high
mounted rocker switch to help slow the vehicle when enough to continue the fan operation.
the accelerator is released. See Chapter 7 under the
heading "Exhaust Braking System, Optional" for addi- To turn the engine fan on, press on the upper part of
tional information. the rocker (at the fan icon). See Fig. 4.21.
To turn the exhaust brake on, press on the upper When the engine fan is running, the fan blade icon is
part of the rocker (at the light inside the switch). The backlit in amber. When the panel lights are on, the
exhaust brake turns off automatically. See Fig. 4.19 ENG FAN legend is backlit in green.
or Fig. 4.20.
01/04/2011 f610590
11/28/2001 f610589
Fig. 4.21, Engine Fan Switch
Fig. 4.19, Exhaust Brake Switch
Transmission Controls
If so equipped, the transmission range control valve
and splitter valve are attached to the gearshift knob.
Transmission shift pattern labels are located inside
the cab. See Chapter 8 for complete transmission
operating instructions.
On vehicles with standard Allison On-Highway Series
automatic transmission, the shift selector is lever-
activated. The display mounted on the steering col-
umn provides four forward ranges and one reverse
range. See Fig. 4.22.
03/31/2009 f610589a When the transmission is in D (drive), the vehicle will
operate in the overdrive (5th) gear. To shift down into
Fig. 4.20, Exhaust Brake Switch the direct drive (4th) gear, use the overdrive lockout
switch (O/D legend). See Fig. 4.23. The transmission
When the exhaust brake switch is on, an amber LED will shift into 4th gear and remain in that gear unless
illuminates inside the switch. When the panel lights a range inhibitor is active, such as engine overspeed.
are on, the EXHST BRK legend is backlit in green. See Chapter 8 for more information about range
inhibitors.
To shift to fourth gear, press on the upper part of the
rocker (at the LED). The LED will come on and stay
4.9
Truck-Manuals.net
Controls
Axle Switches
1 All axle switches contain a red LED (light-emitting
diode) that illuminates the switch from within when
the switch is turned on (the upper part of the rocker
is pressed). The legend under the LED, if any, is not
visible until the switch is turned on.
2 IMPORTANT: A guard is positioned around all

axle switches to prevent unintentional activation.
NOTE: For more information on axle switch
function, see Chapter 8.
Differential Lock Switch
3
CAUTION
Differential lock should only be engaged when
01/22/2003 f270119
the vehicle is stopped or moving slowly at low
throttle. This will prevent internal axle damage.
1. All Series, Standard (without park)
2. 1000/2400 Series, Optional (with park) The differential lock switch is a two-position guarded
3. 2000 Series, Optional (with auto-apply parking rocker switch. See Fig. 4.24. It causes the wheels on
brake) each axle governed by the switch to rotate together.
Fig. 4.22, Steering Column-Mounted Shift Controls
It is also known as side-to-side wheel lock.
10/26/2001 f610596
Fig. 4.24, Differential Lock Switch

01/22/2003 f610638
To lock the wheels together, press the upper half of

Fig. 4.23, Overdrive Lockout Switch
the rocker momentarily (at the LED). To turn off dif-
illuminated until the bottom part of the rocker switch ferential lock, press the upper half of the rocker
is pressed. again.
On vehicles with Allison MD Series automatic trans- When the panel lights are on, the double-axle icon is
mission or Eaton Autoshift automated transmission, a backlit in green.
push-button shift selector provides four, five, or six IMPORTANT: The differential lock switch is
forward ranges and one reverse range. See Chap-
ter 8 for more information about the push-button shift
guarded to prevent unintentional switch activa-
selector. tion. If the LED in the switch begins to blink dur-
ing normal operation, when the switch has not
been activated, this indicates an error condition.
4.10
Truck-Manuals.net
Controls
Bring the vehicle to an authorized Freightliner The axle shift switch is a two-position guarded rocker
service facility as soon as possible. switch installed on vehicles with two-speed axles.
See Fig. 4.26.
Interaxle Lock Switch
CAUTION
The interaxle lock should not be engaged on a
vehicle with obviously spinning wheels. Engage-
ment at high speed or power can damage the
axle(s).
The interaxle lock switch is a two-position guarded
rocker switch installed on vehicles with dual drive 10/26/2001 f610594
axles. See Fig. 4.25. It causes both axle shafts to
rotate together. Fig. 4.26, Axle Shift Switch
To shift the axle from low speed to high speed, press

the upper half of the rocker momentarily (at the
LED). To turn the axle shift off (switch from high
speed back to low speed), press the upper half of
the rocker again.
NOTE: On vehicles with tandem drive axles,
there is an interlock that prevents a 2-speed
axle from shifting whenever the interaxle lock is
on.
10/26/2001 f610595
When the panel lights are on, the AXLE SHIFT leg-
Fig. 4.25, Interaxle Lock Switch end is backlit in green.
To lock the axles together, press the upper half of the IMPORTANT: The axle shift switch is guarded to
rocker momentarily (at the LED). To turn off interaxle prevent unintentional switch activation. If the
lock, press the upper half of the rocker again. LED in the switch begins to blink during normal
When the panel lights are on, the double-axle icon is operation, when the switch has not been acti-
backlit in green. vated, this indicates an error condition. Bring the
vehicle to an authorized Freightliner service fa-
IMPORTANT: The interaxle lock rocker switch is cility as soon as possible.
guarded to prevent unintentional switch activa-
tion. This switch does not have a diagnostic
blink function when inactive. All-Wheel-Drive Controls,
Optional
Axle Shift Switch
All-wheel-drive (AWD) allows the driver to direct
driveline power to all four axles, front and rear. Two
CAUTION switches are used to control AWD: an AWD operation
switch used to activate all-wheel-drive, and an AWD
To prevent transmission and axle damage, make
range switch used to select the high or low range.
sure the automatic transmission is in high range
AWD controls are not multiplexed.
when performing an axle shift with the vehicle
moving.
4.11
Truck-Manuals.net
Controls
AWD Operation Switch at the upper end and HIGH RANGE at the lower
end. On vehicles with a power take-off unit (PTO),
The AWD operation switch is a two-position rocker the three-position switch has a neutral (N-TRL) posi-
switch with a light-emitting diode (LED) that illumi- tion in the middle. See Fig. 4.28. When the panel
nates when AWD is engaged. The legend LOCKED lights are on, the HIGH RANGE legend is backlit in
is underneath the LED on the upper half of the green.
switch. On the lower half is the legend AWD. See
Fig. 4.27. When the panel lights are on, the AWD
legend is backlit in green. 1 2
LO LO
RANGE N−TRL
LOCKED HIGH HIGH

RANGE RANGE
AWD
07/21/2006 f610808
1. Two-Position Switch
08/10/2006 f610807
2. Three-Position Switch
Fig. 4.27, AWD Operation Switch Fig. 4.28, AWD Range Switches
To engage AWD, press the upper half of the rocker Two-Position Switch (no PTO)
switch. The LED illuminates to indicate that AWD is
engaged. To turn off AWD, press the lower half of the On vehicles without a PTO, high range is considered
switch. The LED goes out to indicate the AWD is no standard operation. To activate the low range, press
longer engaged. the upper half of the switch. When the low range is
activated, the LO RANGE legend is backlit in red. In
When AWD is engaged, the LOCKED legend is addition, a red indicator with the legend T-CASE LO
backlit in red. In addition, a red indicator with the leg- RNG displays on the dash message center. To
end T-CASE ENGAGED displays on the dash mes- switch back to HIGH RANGE, press the lower half of
sage center. the switch.
AWD Range Switch Three-Position Switch (with PTO)
IMPORTANT: Always use the N-TRL switch po-
CAUTION sition when operating the PTO.
To prevent damage to the transfer case and the On vehicles with a PTO, neutral is considered stan-
driveline, stop the vehicle and apply the parking dard operation (switch in the middle position). An
brake before using the range switch. amber indicator with the legend T-CASE NTRL dis-
The AWD range switch is used under similar condi- plays on the dash message center.
tions to those of the axle shift switch on a two-speed To activate the high range, press the lower half of the
rear axle. Use the high range when driving at normal switch. No indicator displays on the dash message
speeds under off-road conditions, or on non-paved center with the high range activated. Press the upper
surfaces. Use the low range when extra traction is half to return to N-TRL.
needed at lower speeds; for example, under condi-
tions of mud, snow, or ice. This switch should be To activate the low range, press the upper half of the
used only when AWD has been engaged. switch. A red indicator with the legend T-CASE LO
RNG displays on the dash message center. On the
In most cases, the AWD range switch is a two- switch, the LO N-TRL legend is backlit in red. Press
position rocker switch with the legends LO RANGE
4.12
Truck-Manuals.net
Controls
the lower half to return to N-TRL, and then press the Trailer Brake Lever
lower half again to select HIGH RANGE.
The trailer brake lever (hand control valve) is used
for applying the trailer brakes without applying the
Braking truck or tractor brakes. It is usually mounted on the
Parking Brake Control Valve right-hand control panel. See Fig. 4.30. See Chap-
ter 9 under the heading "Dual Air Brake System" for
The yellow diamond-shaped knob (Fig. 4.29) on the operating instructions.
auxiliary dash panel operates the parking brake con-
trol valve (park brake switch). Pulling the yellow knob
applies the tractor parking brakes (spring brakes).
Pushing in the knob releases the tractor parking
brakes. Before the parking brakes can be released,
the air pressure in either air brake system must be at
least 65 psi (448 kPa).
1
2
10/17/2001 f610591
Fig. 4.30, Trailer Brake Lever

03/10/99 f610291
Meritor™ WABCO® Antilock Braking
1. Trailer Air Supply Valve (red knob)
2. Parking Brake Control Valve (yellow knob) System (ABS)
Fig. 4.29, Brake Valve Control Knobs The Meritor WABCO Antilock Braking System (ABS)
has an amber tractor indicator light (TRACTOR ABS
See Chapter 9 under the heading "Dual Air Brake legend) and, if equipped with automatic traction con-
System" for further information about the parking trol (ATC), an amber wheel spin indicator light
brake control valve. (WHEEL SPIN legend). See Fig. 4.31.
On vehicles equipped with a compatible trailer, there
Trailer Air Supply Valve is also an amber trailer indicator light (TRAILER ABS
The red octagonal-shaped knob (Fig. 4.29) on the legend).
auxiliary dash panel operates the trailer air supply See the brake system operating instructions in Chap-
valve. After the vehicle and its air hoses are con- ter 9 for more information about ABS.
nected to a trailer, and the pressure in the air system
is at least 65 psi (448 kPa), the red knob must be
pushed in (and should stay in) to charge the trailer
Adjustable Steering Column
air supply system and release the trailer spring park- To tilt the steering column, press down on the foot
ing brakes. Before disconnecting a trailer or when pedal located below the steering column. Tilt the
operating a vehicle without a trailer, the red knob steering column up or down to the desired position.
must be pulled out. Release the foot pedal to lock the steering column in
See Chapter 9 under the heading "Dual Air Brake place. See Fig. 4.32.
System" for further information about the trailer air To telescope the steering column, press down on the
supply valve. foot pedal located below the steering column. Pull
the steering wheel closer to you or push the steering
4.13
Truck-Manuals.net
Controls
2
1 3
5
1
10/12/2000 f610454
1. Tractor ABS Indicator 3. Trailer ABS Indicator
2. Wheel Spin Indicator 3
(optional)
Fig. 4.31, ABS Indicator Lights
wheel farther away from you. Release the foot pedal 4

to lock the steering column in place.
Other Dash-Mounted Controls

Windshield-Fan Switches, Optional
Ceiling-mounted defogger fans are operated by
LOW/OFF/HIGH toggle switches located in the base
of the fan. 07/19/2006 f610799
1. Multifunction Turn 4. Adjustable Steering
Cigarette Lighter Signal Switch Column foot Pedal
Push in the lighter to heat the element. The lighter 2. Headlight Switch 5. Steering Wheel
3. Ignition Switch
will stay in and will automatically pop out when the
element is hot. Fig. 4.32, Adjustable Steering Column
CB Radio Connections
NOTICE
An antenna connection and positive (+) and negative
(–) power connections are provided for a CB radio. Never exhaust air from the suspension while
driving. When the air is exhausted, the suspen-
Suspension Dump Switch sion will not absorb road shocks, and compo-
nents may be damaged.
NOTICE The suspension dump switch is a two-position
guarded rocker switch (Fig. 4.33). It allows the air in
Do not operate the vehicle over uneven ground the vehicle air suspension to be quickly exhausted,
such as ramps, speed bumps, curbs, etc. with lowering the rear of the vehicle. This makes it easier
the air springs deflated. Doing this may lead to to connect to, or disconnect from, a trailer.
air bag separation from the piston, preventing the
To lower the rear of the vehicle quickly, press the
suspension air springs from reinflating.
upper half of the rocker momentarily (at the LED). To
4.14
Truck-Manuals.net
Controls
will also autofill if the vehicle is operated with the

suspension dumped, and the speed is over 5 mph
(e.g. -- driver forgot to inflate the bags or there was a
system failure).
Suspension Autofill Override Valve

The suspension autofill override option is a dash air
valve, that keeps the suspension deflated when the
ignition is turned off. To operate it, turn off the ignition
10/26/2001 f610597 then push the override valve knob. See Fig. 4.34.
When the ignition is turned on, the override valve will
Fig. 4.33, Suspension Dump Switch release automatically, and the suspension will autofill.
The suspension dump switch will then operate nor-
raise the suspension to its normal height, press the mally as described previously.
upper half of the rocker again.
When the panel lights are on, the tractor icon is
backlit in green.
IMPORTANT: The suspension dump switch is
SH TO
guarded to prevent unintentional switch activa- PU
tion. This switch does not have a diagnostic
blink function when inactive.
When the suspension dump switch is pressed, three
responses are possible: a normal response, a slow
response, and an abnormal response.
Normal Response: The LED in the switch blinks
while the suspension is deflating or filling. When it is
completely deflated, the LED comes on steady and
stays illuminated. In normal operation, the suspen-
sion may dump or fill so quickly that the blinking of
the switch is barely noticeable. 09/11/2007 f321102
If operation of the switch is not possible for any rea- Fig. 4.34, Suspension Autofill Override Valve
son (vehicle is moving faster than 5 mph, ignition is
turned off, etc.), the LED will stop blinking and turn Heater/Air Conditioner Control
off.
Slow Response: If operation of the switch is slowed
Panel
for any reason (by cold weather, low air pressure, Standard controls (Fig. 4.35) for the heating, ventila-
etc.), the switch will continue to blink until the sus- tion, and air-conditioning system (HVAC) consist of
pension completes a dump or fill. As in the normal an eight-speed fan switch, an air selection switch,
response, the LED comes on steady and stays illumi- and a temperature control switch. On vehicles with
nated when the suspension if fully deflated. air conditioning, the panel also contains a telltale
Abnormal Response: If the LED blinks for more than LED and an air recirculation button. See Chapter 6
10 seconds, the suspension dump mechanism may for detailed operating instructions for the HVAC.
not be operating properly. Bring the vehicle to an au-
thorized Freightliner service facility for testing. Seat Controls
If the ignition is turned off while the vehicle is in Bench Seat Adjustment Controls
dump mode, the power to the dump solenoid is cut
off to prevent battery drain, and the suspension sys- The standard bench seat has one control: the seat
tem will autofill the rear air springs. The suspension slide lever. See Fig. 4.36. The two-person bench
4.15
Truck-Manuals.net
Controls
1 2 3
seat to prevent damage to the seat and the cab inte-
rior.
All adjustment controls for a suspension seat are lo-
2
1 3 cated on the seat base. See Chapter 5 for complete
instructions.
0 4
10/03/2001 f831452
1. Fan Switch
2. Air Selection Switch
3. Temperature Control Switch
Fig. 4.35, HVAC Climate Control Panel, Standard
seat and the non-suspended passenger seat have

no controls.
2
10/05/2001 f910481
1. Three-Person Seat
2. Seat Slide Lever
Fig. 4.36, Full Bench Seat
Suspension Seat Adjustment Controls

All controls for adjusting air suspension seats are
located within easy reach of the occupant.
Due to the maximum adjustability of mid- and high-
back air suspension seats, it is possible to combine
the seat back recline adjustment and the seat slide
adjustment so that the seat back contacts the back-
wall. It is the responsibility of the driver to adjust the
4.16
Truck-Manuals.net
5
Cab Features
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Seat Belts and Tether Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8
Cab Amenities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11
Windshield Washer Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11
Truck-Manuals.net
Cab Features
Windows Mirrors
Standard windows operate mechanically using a The standard outside mirrors are mounted on the
hand crank. door frame. There is a primary rear view mirror and a
convex mirror.
Power windows are optional, and can be installed on
one side or both sides. One power window switch
(window icon) will be installed on the dash for each
Mirror Heat Switch, Optional
window. See Fig. 5.1. If your vehicle is equipped with One or both outside door mirrors can be heated to
power windows, press up to raise the window; press keep them clear of fog, frost, and ice.
down to lower the window. Releasing the switch
causes the window to stop. To heat the mirrors, press the upper part of the mir-
ror heat switch (MIRR HEAT) on the dash. See
Fig. 5.3. When the mirror heat switch is on, an
amber indicator light illuminates inside the switch.
MIRR
HEAT
10/09/2001 f610522
Press up to raise the window; press down to lower the
window. Releasing the switch causes the window to stop.
10/09/2001 f610524
Fig. 5.1, Power Window Switch To heat the mirrors, press up; press down to turn off the
heat.
Standard vent (wing) windows do not open. Operat-
ing vent windows are optional. To open the operating Fig. 5.3, Mirror Heat Switch
vent window, turn the latch on the window and push
the window open. See Fig. 5.2. The mirror heat switch is a smart switch (fully multi-
plexed).
Power Mirrors, Optional

The main outside mirrors, if heated, can be equipped
with an electrical remote control located on the
driver’s door. See Fig. 5.4.
1 To select the mirrors on the left-hand side, press the

left side of the mirror select switch. To select the mir-
rors on the right-hand side, press the right side of the
mirror select switch.
The keypad has four arrow keys, pointing up, down,
2 left, and right. To adjust the mirror position, press the
keypad in the direction you want the mirror to move.
10/05/2001 f670096
1. Latch 2. Vent Window Down View Mirror, Optional
Fig. 5.2, Operating Vent Window (optional) A down view mirror can be installed on the top of the
passenger door frame to allow the driver a view of
5.1
Truck-Manuals.net
Cab Features
the area adjacent to the right side of the cab. See Unless otherwise noted, all seat adjustments should
Fig. 5.5. be made while seated and before the engine is
started.
Due to the high degree of adjustability found in high-
2
back air suspension seats, it is possible to set the
seat back recline adjustment and the seat slide ad-
justment in such a combination that the seat back
1 will come into contact with the rear wall of the cab. It
is the responsibility of the driver to adjust the seat to
prevent damage to the seat and the cab interior.
The following is a description of adjustments that are
available on one or more seats. Not all seats have all
of the adjustments listed below.
10/05/2001 f610523 1. Seat Slide (fore-and-aft): When this adjustment is
To adjust the mirror position, press the keypad on the
made, the entire seat moves forward or back-
door in the direction you want the mirror to move. ward on its track (Fig. 5.6).
1. Mirror Select Switch 2. Keypad
Fig. 5.4, Power Mirror Switch Pad
B
10/05/2001 f720396 10/05/2001 f910482
1. Mirror A. Seat Slide (fore-and-aft) Adjustment

B. Isolator Feature
Fig. 5.5, Down View Mirror (optional)
Fig. 5.6, Seat Slide Adjustment and Isolator Feature
Seats 2. Isolator: This feature (also referred to as back-
General Information slap isolator or Chugger-Snubber®) reduces the
amount of road shock by isolating the occupant
from the motion of the vehicle, and allowing the
WARNING upper seat to move in a simple pendulum mo-
tion. Whenever the isolator is not desired, it can
Keep hands, tools, and other objects away from be locked out (Fig. 5.6).
the scissor points under the seats. Failure to do
so could cause personal injury. 3. Lumbar Support: Lumbar support changes the
shape of the seat back to give more or less sup-
port to the occupant’s lumbar (lower back) area.
5.2
Truck-Manuals.net
Cab Features
This adjustment is either mechanical or air con-

trolled, depending on make and model of the
seat (Fig. 5.7).
B
A
10/05/2001 f910484
A. Backrest Tilt B. Seat Cushion Tilt
Fig. 5.8, Cushion Tilt Adjustments
10/05/2001 f910483
A. Lumbar Support B. Headrest Adjustment
Fig. 5.7, Lumbar Support and Headrest Adjustment
4. Headrest: When this adjustment is made, the

upper part of the backrest (back cushion)
changes angle to provide head and upper back A
support (Fig. 5.7).
5. Backrest Tilt: This adjustment pivots the backrest
forward or backward (Fig. 5.8).
6. Seat Cushion Tilt: This adjustment raises or low-
ers the front and/or back of the seat (bottom)
cushion. This adjustment is easier to perform
when all weight is removed from the seat
(Fig. 5.8).
10/05/2001 f910485
7. Seat Tilt: When this adjustment is made, the seat A. Ride Height
assembly, both backrest and seat cushion, tilts
forward or backward (Fig. 5.8). Fig. 5.9, Ride Height Adjustment
8. Ride Height Adjustment: The entire seat moves mal driving conditions, the seat should not top or
up or down when adjusting the ride height. The bottom against the limits of the vertical travel.
adjustment is either manual or air controlled, de-
pending on the make and model of the seat 10. Ride Firmness: A firmer ride gives a better feel
(Fig. 5.9). for the road but less protection against uneven-
ness in the road surface. A softer ride smooths
9. Damper: When you sit on the seat, a leveling out the bumps.
valve places you in the center of the ride zone.
When the damper is adjusted properly under nor-
5.3
Truck-Manuals.net
Cab Features
Bench Seats Lumbar Support

The three-person full bench seat is standard. See To adjust the lumbar support, use the lumbar support
Fig. 5.10. switches on the side of the seat.
Height Adjustment
To raise or lower the height of the seat, use the
1 height adjustment switch on the side of the seat.
Bottom Cushion Extension

To adjust the fore-and-aft position of the seat cush-
ion, remove your weight from the seat, then lift up
and pull forward on the cushion adjustment handle.
To return the cushion to the aft position, lift up and
push rearward.
Fore/Aft Seat Slide

To adjust the fore-and-aft position of the entire seat,
move the fore-and-aft seat adjustment lever to the
2
left and slide the seat forward or backward to the
10/05/2001 f910481 desired position. Move the lever back to its original
1. Three-Person Seat position to lock the seat in place.
2. Seat Slide Lever
Fore/Aft Isolator
Fig. 5.10, Full Bench Seat
To engage the isolator, turn the isolator knob rear-
The full bench seat has a seat slide adjustment to ward to the unlocked position. Turn the isolator knob
allow more or less leg room for the driver and pas- forward to the locked position when the isolator fea-
sengers. Release the seat slide lever and push back- ture is not desired.
wards or forwards to move the seat along its track.
High-back air suspension seats are optional for both Shock Absorber
driver’s and passenger’s seats. Also available are a To adjust the amount of damping the shock absorber
non-suspended passenger’s seat, and a two-person provides, move the lever up to increase damping;
bench seat with a safe or tool box located under the move the lever down to decrease damping.
seat.
No adjustments are possible on the two-person Front Cushion Height
bench seat or the non-suspended passenger seat. To adjust the height of the front of the cushion, re-
move your weight from the seat, then turn the adjust-
Freightliner High-Back Seat ment knob toward the front of the seat (clockwise) to
See Fig. 5.11 for seat adjustment controls. Not all increase cushion height. To lower the cushion height,
models of the seat have all the adjustments listed turn the adjustment knob toward the rear of the seat
below. (counterclockwise).
Backrest Tilt Rear Cushion Height

To tilt the backrest, lean forward slightly to remove To adjust the height of the rear of the seat cushion,
pressure from the cushion, then turn the knob for- remove your weight from the seat and turn the rear
ward or rearward to achieve the desired position. cushion adjustment knob to one of three positions.
5.4
Truck-Manuals.net
Cab Features
1
6
2 4 10
3 9
5 8
7
07/18/2007 f910576
NOTE: Not all models of the seat have all the adjustment controls shown.
1. Rear Cushion Height Adjustment 4. Bottom Cushion Extension Handle 8. Shock Absorber Lever
Knob 5. Fore/Aft Seat Slide Lever 9. Height Adjustment Switch
2. Fore/Aft Isolator 6. Backrest Tilt Knob 10 Lumbar Support Switches
3. Front Cushion Height Adjustment 7. Heater Button
Knob
Fig. 5.11, Freightliner High-Back Seat
Heater Isolator
To turn on the heat option, press the button. To turn To engage the isolator, put the seat slide and isolator
off the heat option, press the button again. If the ve- lever in the center position. Lock out the isolator by
hicle has Optimized Idle, seat heating will not oper- moving the lever to the right.
ate with the key in accessory mode. Optimized Idle
may also turn seat heating off to reduce stress on Lumbar Support
the batteries.
To increase lumbar support, rotate the lumbar sup-
port knob forward. To decrease lumbar support, ro-
Bostrom Seat tate the knob rearward.
Seat Slide Adjustment On seats equipped with air lumbar support, press the
Move the seat slide and isolator lever (Fig. 5.12) to control valve upward to increase lumbar support.
the left and hold it there to slide the seat forward or Press the control valve downward to decrease lum-
backward to the desired position. bar support.
5.5
Truck-Manuals.net
Cab Features
National 2000 Series Seat

Seat Slide Adjustment
Move the seat slide lever (Fig. 5.13) to the left and
hold it there to slide the seat forward or backward to
the desired position. Move the lever back to its origi-
nal position to lock the seat in place.
1
7
7
6 2
3
4
5 6
10/10/96 f910131
1. Backrest Tilt Lever
2. Air Lumbar Support Control Valve (optional)
1
3. Damper Adjustment Switch 5
4. Height Adjustment Switch
5. Seat Cushion Tilt Knob
6. Seat Slide and Isolator Lever 2
7. Lumbar Support Knob (standard) 4 3
Fig. 5.12, Bostrom Seat
11/14/2000 f910445
Seat Cushion Tilt 1. Backrest Tilt Knob
Rotate the seat cushion tilt knob to increase or de- 2. Lumbar Support Switch
crease seat cushion tilt. 3. Height Adjustment Switch
4. Seat Slide Lever
5. Front Cushion Height Adjustment Handle
Backrest Tilt 6. Isolator Handle
To tilt the backrest, lean forward slightly to remove 7. Rear Cushion Adjustment Knob
pressure from the cushion and hold the backrest tilt Fig. 5.13, National 2000 Series Seat
lever rearward. Lean backward slowly to the desired
position and release the lever to lock the backrest in Isolator
place.
To use the isolator feature, turn the isolator handle to
Ride Height and Damper Adjustment the horizontal position. Turn the isolator handle down
to lock out the isolator.
To raise the seat, press the upper portion of the
height adjustment switch. To lower the seat, press Lumbar Support
the lower portion of the switch.
To adjust the lumbar support, use the lumbar support
Press the damper adjustment switch to adjust the switch on the side of the seat to give more or less
damper. support to your lower back.
5.6
Truck-Manuals.net
Cab Features
Backrest Tilt right. To lock out the isolator, move the isolator lever
to the center position.
To tilt the backrest, turn the backrest tilt knob until
the desired position is reached.
Seat Cushion Adjustment

To adjust the height of the front of the seat cushion,
lift the front cushion height adjustment handle, and 1
pull forward or push back to the desired setting.
To adjust the height of the rear of the seat cushion,
remove your weight from the seat and turn the rear
cushion adjustment knob to one of three positions.
Ride Height Adjustment 2

4
To raise or lower the height of the seat, use the
height adjustment switch on the side of the seat.
5
6
Sears Seat 3
8
Seat Slide Adjustment
Push the seat slide (fore-and-aft adjustment) lever
(Fig. 5.14) all the way to the left and slide the seat 7
forward or backward, as desired. Release the lever 10/09/2001 f910486
to lock the seat in the desired position. NOTE: Armrests are optional.
1. Lumbar Support Lever
4 2. Backrest Lever
3 3. Ride Height Knob
4. Shock Absorber Bracket (ride firmness)
5. Pin (ride firmness)
6. Snap Ring (ride firmness)
5 7. Seat Slide and Isolator Lever
8. Seat Cushion Adjustment
2
Fig. 5.15, Sears Fleetmaster Seat (with isolator)
1 Lumbar Support
Move the three-position lumbar support lever upward
to increase lumbar support (firmer). Move the lever
10/08/2001 f910487 downward to decrease lumbar support (less firm).
1. Seat Slide Lever NOTE: This three-position lever (see inset) does
2. Seat Cushion Tilt Adjustment not rotate a full 360 degrees.
3. Ride Height Knob
4. Lumbar Support Lever For seats with air support, use the aft rocker switch
5. Backrest Lever on the control panel on the left-hand side of the seat
(Fig. 5.16). Press up to make the seat firmer; press
Fig. 5.14, Sears Low Profile Seat
down to make the seat less firm.
Isolator Seat Cushion Tilt
To engage the isolator (if installed), move the seat To raise the seat cushion, lift upward on the front of
slide and isolator lever (Fig. 5.15) all the way to the
the seat cushion, and then push it rearwards. To
5.7
Truck-Manuals.net
Cab Features
Seat Belts and Tether Belts

General Information
Seat belt assemblies are designed to secure persons
in the vehicle to help reduce the chance of injury or
the amount of injury resulting from accidents or sud-
den stops. For this reason, Daimler Trucks North
America LLC urges that the driver and all passen-
gers, regardless of age or physical condition, use
seat belts when riding in the vehicle.
WARNING
10/08/2001 1 2 f910488
1. Ride Height Switch Always use the vehicle’s seat belt system when
2. Air Lumbar Support Switch operating the vehicle. Failure to do so can result
in severe personal injury or death.
Fig. 5.16, Air Controls, Sears Seat
Seat belt assemblies in Daimler Trucks North
lower the seat cushion, pull forward on the front of America (DTNA) vehicles meet Federal Motor Ve-
the seat cushion, and then push downwards. hicle Safety Standard 209, "Type 1" and "Type 2" re-
quirements.
Backrest Adjustment When transporting a child, always use a child re-
To adjust the backrest, push downwards on the back- straint system or the vehicle seat belts as appropri-
rest lever just below the bottom of the backrest cush- ate. To determine whether a child restraint system is
ion. With the lever down, lean forward or backward required, review and comply with applicable state
to the desired position. Release the lever to lock the and local laws. Any child restraint used must comply
backrest in place. with Federal Motor Vehicle Safety Standard 213,
"Child Restraint Systems." When providing a child
Ride Height Adjustment restraint system, always carefully read and follow all
instructions pertaining to installation and usage for
Push the ride height knob inwards to inflate the air the child. Make certain the child remains in the re-
cylinder, raising the height of the seat. Pull the ride straint system at all times when the vehicle is in mo-
height knob outwards to deflate the air cylinder, low- tion.
ering the height of the seat.
In addition to seat belt assemblies, tether belts are
For seats with air support, use the forward rocker installed on suspension-type seats. Tether belts help
switch on the control panel on the left-hand side of secure the seat to the floor and are intended to re-
the seat (Fig. 5.16). Press up to raise the seat; press strain the seat and seat belt in case of an accident or
down to lower the seat. sudden stop.
Ride Firmness Adjustment IMPORTANT: Seat belts have a finite life which
may be much shorter than the life of the vehicle.
For a softer ride, remove the snap ring and pin from Regular inspections and replacement as needed
the shock absorber bracket (see inset). Relocate the are the only assurance of adequate seat belt
pin in the other set of holes in the bracket and se- security over the life of the vehicle.
cure it with the snap ring.
5.8
Truck-Manuals.net
Cab Features
Seat Belt Inspection introduce a small amount of slack into the seat belt,
resulting in a more comfortable ride.
WARNING
Inspect and maintain seat belts. When any part of
a seat belt system needs replacement, the entire
seat belt must be replaced, both retractor and
buckle side. Any time a vehicle is involved in an
accident, and the seat belt system was in use, A B
the entire vehicle seat belt system must be re-
placed before operating the vehicle. Do not at-
tempt to modify the seat belt system; doing so
could change the effectiveness of the system.
Failure to replace worn or damaged seat belts, or
making any modifications to the system, may re-
sult in personal injury or death.
Inspect the seat belts and tether belts (if so
equipped).
1. Check the web for fraying, cuts, extreme dirt and
dust, or for severe fading from exposure to sun-
light, especially near the buckle latch plate and in
the D-loop guide area.
03/11/2010 f910620
2. Check operation of the buckle, latch, Komfort A. Disengaged B. Engaged
Latch or Sliding Komfort Latch (if equipped), web
retractor, and upper seat belt mount on the door Fig. 5.17, Komfort Latch
pillar. Check all visible components for wear or
damage.
3. Check the seat belt and tether belt connection
points and tighten any that are loose.
Seat Belt Operation

Three-Point Seat Belt With Komfort Latch
or Sliding Komfort Latch
WARNING
Wear three-point seat belts only as described
below. Three-point seat belts are designed to be
worn by one person at a time. In case of an acci-
dent or sudden stop, personal injury or death
could result from misuse.
Fasten the seat belts before driving. Fastening a
three-point seat belt while driving creates a haz- 11/18/2010 f910621a
ard.
Fig. 5.18, Sliding Komfort Latch
When engaged and used properly, the Komfort Latch
(Fig. 5.17) and the Sliding Komfort Latch (Fig. 5.18) 1. Slowly pull the latch end of the three-point seat
belt out of the retractor and pull it across your
5.9
Truck-Manuals.net
Cab Features
lap (from outboard to inboard) far enough to en- If equipped with a Komfort Latch, pull on the
gage the buckle. If the retractor locks too soon, shoulder strap to lessen the pressure of the strap
allow the belt to retract slightly, then slowly pull it on your shoulder and chest. Allow no more than
out again. 1 inch (2.5 cm) of slack between your chest and
the shoulder harness. More slack can signifi-
2. Fasten the three-point seat belt by pushing the cantly reduce the seat belt effectiveness in an
latch into the buckle. Listen for an audible click. accident or a sudden stop. While holding the belt
See Fig. 5.19. slack, press the Komfort Latch lever up, clamp-
ing the seat belt webbing (Fig. 5.20 and
Fig. 5.21).
01/18/95 f910004a 01/06/95 f910048a

A. 1 Inch (2.5 cm) Maximum
Fig. 5.19, Fastening the Three-Point Belt
Fig. 5.20, Adjusting Shoulder Harness Clearance,
3. Tug on the seat belt to make sure it is securely Komfort Latch
fastened. If the buckle unlatches, repeat this
step. If the problem continues, replace the three-
point seat belt.
4. Snug the seat belt to your waist.
5. Position the shoulder strap diagonally across
your chest with the adjustable D-loop bracket (if
equipped). If desired, engage the Komfort Latch
or Sliding Komfort Latch as follows.
If equipped with a Sliding Komfort Latch, make
sure that the shoulder strap is snug against your
chest. Without loosening the shoulder strap,
push the Sliding Komfort Latch switch to the
"ON" position. See Fig. 5.18. To activate the
11/02/95 f910144
latch lean forward until you hear a click. This will
allow for approximately 1 inch (2.5 cm) of slack
Fig. 5.21, Locking the Komfort Latch
between your chest and the shoulder harness.
Once engaged, the latch will allow you to lean 6. Unbuckle the three-point seat belt and release
forward about 5 inches (13 cm) without having to the Komfort Latch or the Sliding Komfort Latch
reset the latch. Leaning forward more than 5 as follows.
inches (13 cm) will disengage the Sliding Kom-
fort Latch, requiring it to be reset. If equipped with a Sliding Komfort Latch, un-
buckle the seat belt, then tug on the shoulder
5.10
Truck-Manuals.net
Cab Features
belt to release the Sliding Komfort Latch, or Center Storage Console (optional)
press the Sliding Komfort latch to the "OFF" po-
sition, then unbuckle the seat belt. On vehicles with individual driver’s and passenger’s
seats, a center storage console can be installed be-
If equipped with a Komfort Latch, unbuckle the tween the seats.
seat belt, then release the Komfort Latch by giv-
ing the shoulder belt a quick tug. If you lean for- The center storage console has a table top that can
ward against the shoulder belt, the Komfort Latch be lifted up to deploy a writing surface. See
will automatically release, and will need to be Fig. 5.23.
reset. In another version, the center storage console has a
NOTE: Neither the Komfort Latch nor the Sliding printer top with a paper slot in it. See Fig. 5.24.
Komfort Latch need to be manually released in
an emergency situation. Each will release by Windshield Washer Reservoir
itself under rough road or other abnormal condi-
The standard location for the windshield washer res-
tions. Make sure the three-point seat belt is
ervoir is on the right-hand side of the cab underneath
completely retracted when it is not in use. the door, just above the trailing edge of the top cab
step. See Fig. 5.25.
Cab Amenities
Cup Holders
There are two cup holders molded into the lower part
of the auxiliary dash panel, one on either side of the
HVAC control head.
Cab Storage
There are storage bins in the dash and the overhead
console. On vehicles with optional individual driver’s
and passenger seats, there is a center storage con-
sole between the seats.
There is a dash storage bin located under the cup
holders on the center panel. The bin has a hinged
cover and can be used to store sunglasses. There is
also a small storage pocket above the radio.
Overhead Storage
Vehicles without an overhead console have two stor-
age bins located above the windshield.
On vehicles equipped with an overhead console,
most vehicles have a storage bin located in the over-
head console. See Fig. 5.22. The overhead storage
bin is often removed and replaced with a CB radio.
Two map holders with netted openings are located
overhead, one on either side of the overhead
console.
5.11
Truck-Manuals.net
Cab Features
1 2
10/08/2001 f680027
1. Overhead Storage Bin 2. Overhead Console 3. Map Holder Netting
Fig. 5.22, Overhead Storage
1
1
2 2
3
3
10/08/2001 f680025
1. Printer Top 3. Storage Console Base
10/08/2001 f680026 2. Printer/Paper Area
1. Table Top Fig. 5.24, Center Storage Console (printer option)
2. Storage Console Cover
3. Storage Area
4. Storage Console Base
Fig. 5.23, Center Storage Console (with writing surface)
5.12
Truck-Manuals.net
Cab Features
1
2
10/08/2001 f820378a
1. Cab
2. Washer Reservoir Fill Cap
3. Top Step
Fig. 5.25, Windshield Washer Reservoir
5.13
Truck-Manuals.net
6
Heater, Ventilator and Air
Conditioner
Climate Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1
Truck-Manuals.net
Heater, Ventilator and Air Conditioner
Climate Control Panel To increase airflow, turn the fan switch to the right or
to a higher number. To decrease the airflow, turn the
The climate control panel allows you to control the switch to the left or to a lower number.
heating, ventilating, defrosting, and air conditioning
functions. The climate control panel without air condi- Air Selection Switch
tioning is shown in Fig. 6.1. The climate control
panel with air conditioning is shown in Fig. 6.2. The air selection switch allows you to control the flow
of air through the face outlets, the floor outlets, the
Fan Switch defrost (windshield) outlets, or a combination of
these outlets to give you nine air selection modes on
The fan switch controls the fan speed and forces a system without air conditioning. See Fig. 6.3. A
fresh or recirculated air through the air outlets. The system with air conditioning has 11 air selection
fan switch has eight fan speeds and an off position.
1 2 3
2
1 3
0 4
06/17/2003 f831452a
1. Fan Switch 2. Air Selection Switch 3. Temperature Control Switch
Fig. 6.1, Climate Control Panel Without Air Conditioning
1 2 3
2
1 3
0 4
06/18/2003 5 4 f831453a
1. Fan Switch 3. Temperature Control Switch 5. Recirculation Indicator
2. Air Selection Switch 4. Recirculation Button
Fig. 6.2, Climate Control Panel With Air Conditioning
6.1
Truck-Manuals.net
modes, four of which are air conditioning modes. See

6
Fig. 6.4. 5 7
4
3 5 4 8
2 6 3 9
A
1 7 2 10
8 1 11
06/18/2003 f831462
9 A. Air Conditioning Modes
1. Air Conditioning Face Mode
06/17/2003 f831455 2. Selection Between Air Conditioning Face Mode and
1. Face Mode Air Conditioning Bi-Level Mode
2. Selection Between Face Mode and Bi-Level Mode 3. Air Conditioning Bi-Level Mode
3. Bi-Level Mode 4. Selection Between Air Conditioning Bi-Level Mode
4. Selection Between Bi-Level Mode and Floor Mode and Face Mode
5. Floor Mode 5. Face Mode
6. Selection Between Floor Mode and Floor/Defrost 6. Selection Between Face Mode and Floor Mode
Mode 7. Floor Mode
7. Floor/Defrost Mode 8. Selection between Floor Mode and Floor/Defrost
8. Selection Between Floor/Defrost Mode and Defrost Mode
Mode 9. Floor/Defrost Mode
9. Defrost Mode 10. Selection between Floor/Defrost Mode and Defrost
Mode
Fig. 6.3, Air Selection Switch Without Air Conditioning 11. Defrost Mode
Fig. 6.4, Air Selection Switch With Air Conditioning

Air Selection Switch Without Air
Conditioning through the floor outlets and 25 percent through
1. Face Mode: Directs all airflow through the face the defrost outlets.
or instrument panel outlets. 7. Floor/Defrost Mode: Directs the airflow equally
2. Selection between Face Mode and Bi-Level to the floor outlets and the defrost outlets.
Mode: Directs 75 percent of the airflow through 8. Selection between Floor/Defrost Mode and
the face outlets and 25 percent through the floor Defrost Mode: Directs 75 percent of the airflow
outlets. through the defrost outlets and 25 percent
3. Bi-Level Mode: Directs the airflow equally to the through the floor outlets.
face outlets and the floor outlets. 9. Defrost Mode: Directs all airflow through the
4. Selection between Bi-Level Mode and Floor defrost outlets.
Mode: Directs 25 percent of the airflow through
the face outlets and 75 percent through the floor
Air Selection Switch With Air
outlets. Conditioning
5. Floor Mode: Directs all airflow through the floor 1. Air Conditioning Face Mode: Directs all airflow
outlets. through the face or instrument panel outlets.
6. Selection between Floor Mode and Floor/ 2. Selection between the Air Conditioning Face
Defrost Mode: Directs 75 percent of the airflow Mode and the Air Conditioning Bi-Level
6.2
Truck-Manuals.net
Mode: Directs 75 percent of the airflow to the Recirculation Mode

face outlets and 25 percent to the floor outlets.
The recirculation mode is only available on vehicles
3. Air Conditioning Bi-Level Mode: Directs the with air conditioning.
airflow equally to the face outlets and the floor
outlets. The recirculation mode limits the amount of outside
air entering the cab. Press the recirculation button to
4. Selection between the Air Conditioning Bi- prevent dusty or smoky air from entering the cab.
Level Mode and the Face Mode: Directs 25 The recirculation mode can also be used to decrease
percent of the airflow to the face outlets and 75 the time required to cool or heat the cab interior dur-
percent to the floor outlets. ing extreme outside temperature conditions. When
5. Face Mode: Directs all airflow through the face the recirculation mode is on, the recirculation indica-
outlets. tor will be on. See Fig. 6.2.
6. Selection between Face Mode and Floor The recirculation mode is not available when the air
Mode: Directs the airflow equally through the selection switch is in one of the following modes:
face outlets and the floor outlets. • floor/defrost mode
7. Floor Mode: Directs all airflow through the floor • selection between floor/defrost mode and de-
outlets. frost mode
8. Selection between Floor Mode and Floor/ • defrost mode
Defrost Mode: Directs 75 percent of the airflow
through the floor outlets and 25 percent through When the recirculation mode is turned on, it will stay
the defrost outlets. on for 20 minutes, or until the recirculation button is
pressed again, or the air selection switch is turned to
9. Floor/Defrost Mode: Directs the airflow equally a defrost mode.
to the floor outlets and the defrost outlets. The
recirculation button will not work in this mode. IMPORTANT: On vehicles built before May 2,
2003, the recirculation mode turns off after
10. Selection between Floor/Defrost Mode and twenty minutes and can be turned back on
Defrost Mode: Directs 75 percent of the airflow when the recirculation button is pressed again.
through the defrost outlets and 25 percent
On vehicles built from May 2, 2003, the system
through the floor outlets. The recirculation button
will not work in this mode. enters a partial recirculation mode for five min-
utes after being in full recirculation mode for 20
11. Defrost Mode: Directs all airflow through the minutes. This cycle repeats as long as the sys-
defrost outlets. The recirculation button will not tem is in recirculation mode.
work in this mode.
NOTE: To prevent the buildup of fumes or odors
Temperature Control Switch inside the cab on a vehicle built before May 2,
2003, do not use the recirculation mode for
The temperature control switch is used to select the
more than 20 minutes. It is recommended that
desired temperature. Turn the switch to the left
(counterclockwise) for cool air, or to the right (clock- the recirculation mode remains off for five min-
wise) for hot air. There are 21 positions on the tem- utes before it is turned back on.
perature control switch ranging from full cool air to
full hot air. Defrosting
Before using any of the defrost modes, clear the
Fresh Air Mode screen at the base of the windshield if snow or ice is
Fresh air, or outside air, is circulated through the present.
heating and air conditioning system unless the recir-
culation mode, if equipped, is turned on.
6.3
Truck-Manuals.net
Air Conditioning, Optional Failure to observe these precautions could cause

an explosion or fire, resulting in serious property
There are four air conditioning modes on the air se- damage, and personal injury or death.
lection switch. The air conditioning settings on the air
selection switch are blue, in addition to the selection
between the air conditioning bi-level mode and the
face mode.
IMPORTANT: Operate the air conditioner at
least five minutes each month, even during cool
weather. This helps prevent drying and cracking
of the refrigerant compressor seals and reduces
the chance of refrigerant leaks in the system.
NOTE: The heating and air conditioning system
has a brushless blower motor with a protection
or shutdown mode to prevent damage due to
overheating and overcurrent conditions. If the
brushless blower motor goes into a protection
mode, the motor will operate at a slower speed.
If the overheating or overcurrent condition con-
tinues, the motor will shut down and stop com-
pletely.
The motor will resume proper operation after the
motor has cooled or the overcurrent condition
has been resolved. It will be necessary to cycle
the fan switch off, and then on, to reset the
motor. If the problem appears repeatedly, take
the vehicle to an Freightliner dealer or autho-
rized service outlet for repairs.
Accessory Heaters
Optional accessary heaters are available from the
factory in several configurations. Familiarize yourself
with the equipment on your specific vehicle, and fol-
low the manufacturer’s operating and maintenance
instructions.
WARNING
Do not operate fuel-operated heaters in an area
where flammable vapors, including gasoline or
diesel fumes, are present, such as at filling sta-
tions and tank farms. Turn off a fuel-operated
heater and allow it shut down completely before
entering an area where flammable gases or liq-
uids are present. Heaters continue to operate for
up to three minutes after being turned off.
6.4
Truck-Manuals.net
7
Engines
Emissions and Fuel Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1
Diesel Exhaust Fluid and Tank, EPA10 and Newer Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3
Engine Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7
Cold-Weather Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9
Starting After Extended Shutdown or Oil Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9
Engine Break-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9
Engine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9
Cold-Weather Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10
High-Altitude Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.11
Engine Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.11
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.11
Power Takeoff (PTO) Governor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.13
Engine Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.13
Exhaust Braking Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.15
Truck-Manuals.net
Engines
Emissions and Fuel Efficiency Components may include, but are not limited to, low-
rolling resistance tires; aerodynamic devices such as
IMPORTANT: Depending on local jurisdictional hood, cab/sleeper extenders, and fuel tank fairings;
guidelines, vehicles that are domiciled outside of vehicle speed limiter; and idle shutdown timer. If re-
the U.S. and Canada may not have emissions placement of any drag-reducing component is re-
aftertreatment systems (ATS) that are compliant quired, the replacement component must meet or
with EPA regulations. exceed the drag reduction performance of the origi-
nally installed component in order to maintain compli-
ance with GHG14 requirements.
NOTICE
Follow these guidelines for engines that comply
EPA07 Engines
with EPA07 or newer regulations, or damage may Engines built between January 1, 2007 and Decem-
occur to the aftertreatment device (ATD) and the ber 31, 2009 are required to meet EPA07 guidelines
warranty may be compromised. for reduced exhaust emissions of particulate matter
• Use ultralow-sulfur diesel with 15 ppm sul-
and nitrogen oxides (NOx). NOx is limited to just
over 1 gram per brake horsepower hour (g/bhp-hr),
fur content or less.
and particulate matter cannot exceed 0.01 g/bhp-hr.
• Do not use fuel blended with used engine
The EPA07 ATS varies according to engine manufac-
lube oil or kerosene. turer and vehicle configuration, but the exhaust muf-
• Engine lube oil must have a sulfated ash fler is replaced by an aftertreatment device (ATD).
level less than 1.0 wt %; currently referred Inside the ATD, the exhaust first passes over the die-
to as CJ-4 oil. sel oxidation catalyst (DOC), then passes through
the diesel particulate filter (DPF), which traps soot
IMPORTANT: Using non-specification fuels or particles. The soot is burned to ash during a process
oils can lead to shortened diesel particulate filter called regeneration (regen).
(DPF) cleaning or replacement intervals. For
example, using CJ-4+ oil with 1.3% sulfated ash EPA10 and Newer Engines
(30% more ash content) may result in the need
for DPF cleaning or replacement 20 to 30% The EPA mandates that all engines built after De-
cember 31, 2009 must reduce the level of emissions
sooner than would normally be required. exhausted by the engine to the following levels:
IMPORTANT: See the engine manufacturer’s • Nitrogen Oxides (NOx) – 0.2 g/bhp-hr
operation manual for complete details and op-
eration of the ATS. • Particulate Matter (PM) – .01 g/bhp-hr
To meet EPA guidelines, engines that are compliant
Greenhouse Gas Emissions and Fuel with EPA10 and newer regulations use an ATS that
Consumption Standards has, in addition to a DOC/DPF device like that used
in an EPA07 ATD, a Selective Catalytic Reduction
Vehicles and/or engines manufactured after Decem- (SCR) device to reduce NOx downstream of the en-
ber 31, 2006 and domiciled in the U.S. or Canada gine. After exhaust gases leave the DPF, a controlled
are required to meet all EPA and NHTSA regulations quantity of diesel exhaust fluid (DEF) is injected into
effective as of the vehicle build date. Engines manu- the exhaust stream. In the presence of heat, DEF is
factured between January 1, 2007 and December 31, converted to ammonia gas, which reacts with NOx in
2009 meet EPA07 requirements. Engines manufac- the selective catalyst chamber to yield nitrogen and
tured between January 1, 2010 and December 31, water vapor, which exit through the tailpipe.
2012 meet EPA10 requirements.
Model year 2013 and later vehicles meet additional Regeneration
requirements as specified by GHG14 requirements. The harder an engine works, the better it disposes of
These vehicles are equipped with components that soot. If the exhaust temperature is high enough, a
increase fuel efficiency and reduce GHG emissions. process called passive regeneration (regen) occurs
7.1
Truck-Manuals.net
Engines
as the vehicle is driven normally. However, if the en- NOTE: The regen switch can initiate a parked
gine isn’t running hot enough, the electronic controls regen only when the DPF lamp is illuminated.
may initiate an active regen, whereby extra fuel is
injected into the exhaust stream to superheat and
reduce the soot trapped in the DPF to ash. Active
regen happens only when the vehicle is moving
above a certain speed, determined by the engine
manufacturer. See your engine operation manual for
complete details. Both active and passive regen hap-
pen automatically, without driver input.
WARNING RGEN
Active regeneration can occur automatically any-

time the vehicle is moving. The exhaust gas tem- 03/09/2012 f610848
perature could reach 1500°F (800°C), which is hot
enough to cause a fire, heat damage to objects Fig. 7.1, Regen Request Switch
or materials, or personal injury to persons near
the exhaust outlet. The exhaust temperature can
remain high even after the vehicle has stopped.
When stopping the vehicle shortly after an auto-
matic regen, ensure the exhaust outlets are di-
rected away from structures, trees, vegetation,
flammable materials, and anything else that may
be damaged or injured by exposure to high heat.
See Regen Switches, below, for instructions on
preventing automatic regen if necessary.
When operating conditions do not allow for ATD filter
cleaning by active or passive regen, the vehicle may 07/30/2009 f610944
require a driver-activated parked regen. When this
occurs, the DPF lamp illuminates, indicating that a Fig. 7.2, Regen Request/Inhibit Switch
regen is required. The driver must either bring the
vehicle up to highway speed to increase the load
(thus starting an active regen), or park the vehicle WARNING
and initiate a parked regen. See Regen Switches,
below, for instructions on initiating a parked regen. During parked regen, exhaust temperatures are
very high and could cause a fire, heat damage to
Regen Switches objects or materials, or personal injury to per-
sons near the exhaust outlet.
The regen request switch, located on the dash, is
used to initiate a parked regen. See Fig. 7.1. The Before initiating a parked regeneration, make cer-
function of the switch varies by the engine make and tain the exhaust outlets are directed away from
model in the vehicle. See the engine operation structures, trees, vegetation, flammable materi-
manual for switch operation details. als, and anything else that may be damaged or
injured by prolonged exposure to high heat.
Some vehicles may be equipped with a regen
request/inhibit switch. See Fig. 7.2. To stop a regen To initiate a parked regen, perform the following
in progress or prevent the start of a regen, press the steps.
lower half of the switch. Regen is then delayed until 1. Park the vehicle away from all flammable materi-
the switch is no longer active. als,set the parking brake, and put the transmis-
sion in neutral.
7.2
Truck-Manuals.net
Engines
2. Start and warm the engine until the coolant tem- If the DPF status lamp blinks while the CHECK en-
perature is at least 150°F (66°C). gine lamp is illuminated, initiate a parked regen im-
mediately in order to prevent an engine derate.
3. Lift the regen request switch guard and press
and hold the yellow button for five seconds. As If the red STOP engine lamp illuminates with the
the regen process is initiated, engine rpm in- blinking DPF lamp and the CHECK engine lamp,
creases and the HEST lamp illuminates to indi- begin a parked regen in order to prevent an engine
cate extremely high exhaust temperatures. shutdown. Park the vehicle and perform a parked
regen.
IMPORTANT: The driver must remain with the
vehicle during the entire regen cycle. High Exhaust System Temperature
4. The regen cycle will finish after 20 to 60 minutes, (HEST) Lamp
at which time engine idle speed drops to normal
Slow (10-second) flashing of the high exhaust sys-
and the vehicle can be driven normally. The
tem temperature (HEST) lamp indicates that a
HEST lamp is extinguished when vehicle speed
parked regen is in progress, and the engine’s high
exceeds 5 mph (8 km/h) or the system has
idle speed is being controlled by the engine software,
cooled to normal operating temperature.
not the vehicle driver.
5. To stop a parked regen at any time during the
Steady illumination of the HEST lamp alerts the
process:
driver of high exhaust temperature during the regen
• depress the clutch pedal, brake pedal, or process if the vehicle speed is below 5 mph (8 km/
accelerator pedal; h), or during a parked regen. See Fig. 7.7.
• press and hold the regen inhibit switch until
idle returns to normal;
Maintenance
• shut down the engine. Authorized service facilities must perform any DPF
service. For warranty purposes, maintain a record
that includes:
ATS Warning Lamps
• date of cleaning or replacement;
There are three warning lamps that alert the driver of
high exhaust temperature, the need to perform a • vehicle mileage;
parked regen or service the DPF, or of an engine • particulate filter part number and serial number.
fault that affects emissions. A decal attached to the
driver’s sun visor explains the ATS warning lamps.
Fig. 7.3. Diesel Exhaust Fluid and Tank,
See Fig. 7.4 for an explanation of the ATS warnings, EPA10 and Newer Engines
and actions required to avoid engine protection se-
quences. Diesel Exhaust Fluid
Diesel exhaust fluid (DEF) is used in the ATS to
Malfunction Indicator Lamp (MIL) lower NOx in the exhaust stream. DEF is colorless
A steadily illuminated yellow malfunction indicator and close to odorless (it may have a slightly pungent
lamp (MIL) indicates an engine fault that affects odor similar to ammonia). It is nontoxic, nonflam-
emissions. See Fig. 7.5. mable, and biodegradable. It is mildly corrosive to
aluminum, but does not affect the strength or struc-
DPF Status Lamp ture of the aluminum.
When soot accumulates in the DPF and the DPF sta- White crystals may be noticeable around compo-
tus lamp illuminates, see Fig. 7.6, perform a parked nents that come into contact with DEF. The crystals
regen or bring the vehicle up to highway speed to are easily removed with water.
increase the load (thus starting an active regen). DEF consumption varies depending on ambient con-
ditions and vehicle application.
7.3
Truck-Manuals.net
Engines
IMPORTANT
DPF Regen Needed Diesel Particulate Filter (DPF)
1
regeneration is needed.
If flashing, regenerate as soon as
possible. Engine derate possible.
2
Hot Exhaust Hot exhaust can cause fire.
Keep flammables and people away
from exhaust.
3
DEF Refill Needed Diesel Exhaust Fluid (DEF) level is
low. Engine derate likely.
DEF
Refill tank with certified DEF.
See operator’s manual for complete instructions. 24−01656−000
11/30/2010 f080161
Fig. 7.3, Warning Lamp Decal, Sun Visor
Freezing Conditions DEF Tank

DEF freezes to slush at around 12°F (-11°C). It is not Engines that are compliant with EPA10 and newer
damaged or destroyed if frozen, and is fully usable regulations are equipped with a DEF tank located on
when thawed. The DEF in the tank is allowed to the driver’s side of the vehicle behind the battery box
freeze while a vehicle is non-operational. At start-up, or forward of the fuel tank. See Fig. 7.8 and Fig. 7.9.
normal operation of the vehicle is not inhibited if the The DEF tank has a 19 mm filler neck inlet that pre-
DEF is frozen; an immersion heater with engine cool- vents the hose from a diesel outlet from being in-
ant flowing through it warms the DEF once the en- serted, and has a blue cap for easy identification.
gine is running, allowing the SCR system to operate.
Pre-2013 DEF supply lines are electrically-heated Fuel/DEF Gauge
and are purged when the engine is shut down; com- The diesel fuel and DEF levels are measured in a
plete purging of the DEF lines requires approximately dual-purpose gauge. See Fig. 7.10.
five minutes after the engine is shut down.
Fuel level is indicated at the top of the gauge. Below
DEF supply lines with engine model year 2013 and the fuel level, a low fuel warning lamp illuminates
newer are designed to survive freezing conditions amber when the fuel level drops below 1/8th of the
while containing DEF, so purging is not required. capacity.
The lower portion of the gauge has a DEF warning
lamp that illuminates amber when the DEF tank is
near empty, and a lightbar that indicates the level of
7.4
Truck-Manuals.net
Engines

INDICATOR WARNING
CHECK CHECK STOP
LAMP(S)
(Solid) (Flashing) (Flashing) (Flashing)
Indicator Lamp Filter Regeneration Filter Regeneration Parked Regeneration Parked Regeneration Required − HEST (High Exhaust
Message(s) Recommended Necessary Required − Engine Engine Shut Down System Temperature)
Derate
Diesel Particulate Filter is reaching Filter is now Filter has reached Filter has exceeded Flashing
Filter Condition capacity. reaching maximum maximum capacity. maximum capacity. A regeneration is in
Switch.
capacity. progress.
Required Action Bring vehicle to To avoid engine Vehicle must be Vehicle must be parked and a
highway speeds to derate bring vehicle parked and a Parked Parked Regeneration or Service Solid
allow for an Automatic to highway speeds Regeneration must Regeneration must be performed. Exhaust Components
Regeneration or to allow for an be performed − Check engine operator’s manual and exhaust gas are
perform a Parked Automatic engine will begin for details −engine will shut down. at high temperature.
Regeneration. Regeneration or derate. When stationary, keep
perform a Parked away from people and
Regeneration as flammable materials
soon as possible. or vapors.
See Engine Operator’s Manual for complete Regeneration Instructions.

24−01583−000B
06/29/2009 f080147
Fig. 7.4, ATS Warning Lamps
09/25/2006 f610814a 09/25/2006 f610815a
Fig. 7.5, Malfunction Indicator Lamp (MIL) Fig. 7.6, DPF Status Lamp
DEF in the tank. The DEF light bar illuminates as fol- • One bar illuminated amber—DEF very low, re-
lows: fill DEF
• Four bars illuminated green—Between 75% • One bar flashing red—DEF empty, refill DEF
and 100% full
• Three bars illuminated green—Between 50%
DEF Warnings and Engine Limits
and 75% full IMPORTANT: Ignoring the DEF warning lights
• Two bars illuminated green—Between 25% results in limited engine power, with the applica-
and 50% full tion of a 5 mph (8 km/h) speed limit after the
engine is shut down and started again.
• One bar illuminated green—Between approxi-
mately 10% and 25% full
7.5
Truck-Manuals.net
Engines
09/25/2006 f610816a
Fig. 7.7, HEST Lamp

1
2
07/24/2009 f470541
1. DEF Tank 2. Fuel Tank
Fig. 7.9, DEF Tank Located Forward of the Fuel Tank
• The MIL lamp illuminates

Detroit engines: Power is limited, with a 55 mph (90
km/h) speed limit.
Cummins engines: Power is limited with progres-
sively harsher engine power limits applied.
1 DEF Tank Empty and Ignored

2 If the empty warning is ignored and the DEF tank is
07/24/2009 f470542 not refilled, the red STOP engine lamp illuminates in
addition to the MIL lamp and CHECK engine lamp
1. Batteries 2. DEF Tank
(on vehicles with a Cummins ISB or ISC/L engine.)
Fig. 7.8, DEF Tank Located Behind the Battery Box See Fig. 7.13.
If the DEF is not refilled, a 5 mph (8 km/h) speed
DEF Level Low—Initial Warning limit is applied after the next engine shutdown or if a
When the DEF level is low, the following lamps notify fuel refill is detected.
the driver. See Fig. 7.11. Refill the DEF tank in order
to cancel the warning sequence. DEF Contamination or SCR Tampering
• One bar of the DEF level indicator illuminates
amber—DEF very low, refill DEF NOTICE
• The DEF warning lamp illuminates solid amber Once contaminated DEF or tampering has been
detected, the vehicle must be taken to an autho-
DEF Empty rized service facility to check the SCR system for
When the DEF level reads empty, the following damage and to deactivate the warning lights and
lamps notify the drive. See Fig. 7.12. engine limits.
• One bar of the DEF level indicator flashes If contaminated DEF or tampering with the ATS is
red—DEF empty, refill DEF detected, the DEF warning light flashes and the MIL
• The DEF warning lamp flashes amber
7.6
Truck-Manuals.net
Engines
1/2 1/2 1/2

ULTRA LOW SULFUR ULTRA LOW SULFUR ULTRA LOW SULFUR
DIESEL FUEL ONLY DIESEL FUEL ONLY DIESEL FUEL ONLY
E F E F E F
DEF DEF DEF
1 E F E F E F
2
A B C
11/08/2010 f611037
A. Green bars—DEF level indicators C. One bar flashing red—DEF empty, refill DEF
B. One bar illuminated amber—DEF very low, refill DEF
1. Low Fuel Warning Lamp 2. DEF Warning Lamp
Fig. 7.10, Fuel/DEF Gauge
A A
B B
07/09/2009 f470537 11/08/2010 f470539a

A. DEF Warning Lamp (illuminated) NOTE: MIL illuminates. CHECK engine lamp illuminates
B. DEF Lightbar (one bar amber) if Cummins ISB or ISC/L engine. Engine power is lim-
ited.
Fig. 7.11, DEF Level Low Initial Warning A. DEF Warning Lamp (flashing)
B. DEF Lightbar (one bar flashing red)
lamp illuminates to warn the driver. The CHECK en-
gine lamp also illuminates on vehicles with a Cum- Fig. 7.12, DEF Empty Warning
mins ISB or ISC/L engine. See Fig. 7.13.
plied after the next engine shutdown, or while
• Detroit engines: Engine power is limited with parked and idling.
progressively harsher limits applied. If the fault
is not corrected, the STOP engine light illumi-
nates and a 5 mph (8 km/h) speed limit is ap- Engine Starting
plied after the next engine shutdown or if a fuel For cold-weather starting, refer to "Cold Weather
refill is detected. Starting" later in this chapter.
• Cummins engines: Engine power is limited with
This engine chapter is to serve as a guide for best
progressively harsher limits applied. If the fault practices only. Each make and model engine may
is not corrected, the STOP engine light illumi- have operating characteristics that are unique to that
nates and a 5 mph (8 km/h) speed limit is ap- particular engine, and will be documented in the en-
gine manufacturer’s literature. Always refer to specific
7.7
Truck-Manuals.net
Engines
4. Turn the ignition switch to ON. See Fig. 7.14.

The following actions should occur:
A
• electronic gauges complete a full sweep of
their dials
• warning and indicator lamps illuminate,
then are extinguished
B
• DEF level indicator illuminates all seg-
ments green, then turns them off one at a
11/08/2010 f470540a time before turning the leftmost segment
NOTE: STOP engine light and MIL illuminate, engine amber and then red
power is limited, speed limit of 5 mph (8 km/h)
• During cold conditions, the WAIT TO
A. DEF Warning Lamp (flashing)
B. DEF Lightbar (one bar flashing red) START lamp may illuminate.
Fig. 7.13, DEF Empty and Ignored Warning
instructions and recommendations from the engine

manufacturer.
NOTE: Before starting the engine, read Chap-
ter 3 for detailed information on how to read the
instruments and see Chapter 4 for detailed in-
formation on how to operate the controls. Read
the operating instructions in the manufacturer’s
engine operation manual before starting the
engine.
07/19/2006 f610805
WARNING
Fig. 7.14, Ignition Switch
Never pour fuel or other flammable liquid into the
air inlet opening in the air intake in an attempt to NOTE: The length of time the WAIT TO START
start the vehicle. This could result in a flash fire lamp remains illuminated depends on the ambi-
causing serious personal injury or property ent temperature. The lower the ambient tem-
damage. perature, the longer the lamp will be illuminated.
1. Before engine start-up, complete the pretrip in- NOTE: If the ignition switch is turned to START
spections and maintenance procedures in Chap-
ter 11. before the gauge sweep has completed or if the
starter has overheated, the START BLOCKED
2. Set the parking brake. lamp may illuminate. Turn the ignition switch
3. For manual transmissions, place the transmis- back to ON, wait for the lamp to go out, then
sion in neutral and fully depress the clutch pedal. turn the ignition switch to START again.
Do not depress the accelerator pedal. 5. Once the gauge sweep has completed, turn the
For automatic transmissions, put the transmis- ignition key to the START position. Release the
sion in neutral. Do depress the accelerator pedal. key the moment the engine starts.
NOTE: Depending on local jurisdictional emis-
sions regulations, vehicles and/or engines that NOTICE
are domiciled outside of the U.S. and Canada Do not rev the engine if the oil pressure gauge
may not be equipped with the WAIT TO START indicates no oil pressure. Shut down the engine
or START BLOCKED lamp.
7.8
Truck-Manuals.net
Engines
if oil pressure does not build within approxi-

mately ten seconds. Check to determine the
Engine Break-In
cause of the problem. Operating the engine with Each engine must pass a full-load operating test on
no oil pressure will damage the engine. a dynamometer before shipment, thereby eliminating
6. the need for a break-in. Before running the engine
It is not necessary to idle the engine before en-
for the first time, follow the instructions in the engine
gaging or starting the operation, but load should
manufacturer’s operation manual specific to your en-
be applied gradually during the warm-up period
gine.
until the oil temperature reaches 140°F (60°C).
7. Apply load gradually during the warm-up period. Engine Operation
NOTICE Safety and Environmental
Considerations
If the oil pressure gauge indicates no oil pres-
sure, shut down the engine within approximately All Freightliner diesel engines comply with the re-
ten seconds to avoid engine damage. quirements of the Federal (U.S.) Clean Air Act. Once
an engine is placed in service, the responsibility for
8. Check the oil pressure gauge for any drop in lu- meeting local jurisdictional regulations is with the
bricating oil pressure or mechanical malfunction owner/operator.
in the lubricating oil system. Minimum oil pres-
sure at idle is 7 psi (50 kPa). IMPORTANT: EPA emissions regulations apply
to vehicles domiciled in Canada and the U.S. at
Cold-Weather Starting the time of printing this manual. Vehicles that
are domiciled outside of the U.S. and Canada
Electronic engines do not normally require special may not have engines with an emission after-
starting aids. treatment system that is compliant with EPA
See the engine manufacturer’s operation manual for regulations, depending upon local statutory
starting aids that are approved for specific engines. emissions guidelines.
Starting After Extended NOTICE

Shutdown or Oil Change It is extremely important that the following guide-
Before engine start-up, complete the engine pretrip lines be followed for vehicles with EPA07 or
and post-trip inspections and maintenance proce- newer engines, or damage may occur to the af-
dures in Chapter 11. tertreatment device, and the warranty may be
compromised.
NOTICE • Use ultralow-sulfur diesel with 15 ppm sul-
fur content or less.
Failure to eliminate water-diluted lubricating oil • Do not use fuel blended with used engine
may lead to serious engine damage at startup. lube oil or kerosene.
An engine in storage for an extended period of time • Use only engine lube oil with a sulfated ash
(over winter, for example) may accumulate water in level less than 1.0 wt %; currently referred
the oil pan through normal condensation of moisture to as CJ-4 oil.
on the internal surfaces of the engine. Oil diluted by
water cannot provide adequate bearing protection at Adequate maintenance of the engine and the diesel
start-up. For this reason, change the engine oil and particulate filter (DPF) are the responsibility of the
filters after extended storage. owner/operator, and are essential to keep the emis-
sion levels low. Good operating practices, regular
maintenance, and correct adjustments are factors
that will help keep emissions within the regulations.
7.9
Truck-Manuals.net
Engines
Normal Operation comes too low, raw fuel will wash the lubricating oil
off the cylinder walls and dilute the crankcase oil,
causing all moving parts of the engine to suffer from
WARNING poor lubrication.
Do not operate the engine in an area where flam- If the engine is in good mechanical condition and the
mable vapors such as gasoline or diesel fumes precautions necessary for cold-weather operation are
are present. Shut off the engine when in an area taken, ordinary cold weather will not cause difficulty
where flammable liquids or gases are being in starting or loss of efficiency.
handled. Failure to observe these precautions The following points are important to observe when
could result in serious injury or death. operating in cold weather:
Every engine has an operating range in which it per-
• Check for cracks in the batteries, for corrosion
forms most efficiently. The operating range extends
of the terminals, and for tightness of the cable
from maximum torque rpm at the low end, to engine
clamps at the terminals.
rated speed at the high end. Most engines deliver
best fuel economy when operated in the low- and • Charge the batteries to full capacity. Replace
mid-speed segments of the efficiency range and pro- any battery that is damaged.
duce maximum horsepower at rated speed, which is
• If equipped, turn off the load disconnect switch
also the recommended maximum speed of the en-
gine. For further engine-specific information, refer to after the engine is shut down, to prevent bat-
the engine manufacturer’s operation manual. tery discharge.
Prolonged idling of engines is not recommended, and • Have the alternator output checked at an au-
is illegal in some states. Idling produces sulfuric acid, thorized service provider.
that is absorbed by the lubricating oil, and eats into • Check the condition and tension of the drive
bearings, rings, valve stems, and engine surfaces. If belts.
you must idle the engine for cab heat or cooling, use
the high idle function of the cruise control switches. • Refer to the engine manufacturer’s engine op-
An idle speed of 900 rpm should be enough to pro- eration manual for recommended heaters, low-
vide cab heat in above freezing ambient tempera- viscosity lubricating oils, wintergrade fuels, and
tures. approved coolants.
If the engine is programmed with the idle shutdown
timer, ninety seconds before the preset shutdown NOTICE
time, the CHECK ENGINE light will begin to flash at
a rapid rate. If the position of the clutch pedal or ser- For Detroit engines (EPA07 and newer), use of a
vice brake changes during this final ninety seconds winterfront is not recommended, as it can cause
the idle shutdown timer will be disabled until reset. false fault codes with the engine and aftertreat-
ment system, and possible emission component
failures.
Cold-Weather Operation
If using a winterfront, leave at least 25% of the grille
Satisfactory performance of a diesel engine operating opening exposed in sectioned stripes that run per-
in low ambient temperatures requires modification of pendicular to the charge-air-cooler tube-flow direc-
the engine, surrounding equipment, operating prac- tion. This assures even cooling across each tube,
tices, and maintenance procedures. The lower the and reduces header-to-tube stress, and possible
temperature, the greater the amount of modification chance of component failure. For engine-specific
required. For service products approved for use in guidelines, see below:
cold weather for your engine, see the engine manu-
facturer’s engine operation manual, supplied in the Cummins and Mercedes-Benz engines: A winterfront
vehicle documentation package. may be used to improve cab heating while idling, and
only when the ambient temperature remains below
If satisfactory engine temperature is not maintained, 10°F (-12°C).
maintenance costs will increase due to greater en-
gine wear. If the engine coolant temperature be-
7.10
Truck-Manuals.net
Engines
Detroit engines (EPA07 and newer): Use of a winter- ning, this heat is carried away by oil circulation,
front is not recommended. Using a winterfront can but if the engine is stopped suddenly, the turbo-
cause excessive fan run time, increased fuel con- charger temperature may rise as much as 115°F
sumption, and failure of the DEF system heaters to (46°C).
operate correctly, resulting in fault codes, poor per-
formance, and power reduction. A winterfront should
only be used temporarily in the following situations: NOTICE
• to improve cab heating while idling in an ex- Except in an emergency, do not shut down the
tremely cold ambient temperature; engine when the coolant temperature is above
• when the ambient temperature remains below 194°F (90°C). To do so could damage the engine.
-22°F (-30°C) and the engine is unable to 3. Turn off the ignition switch and shut down the
maintain a running coolant temperature of engine.
175°F (80°C) during normal over-the-road op-
eration.
Cruise Control
High-Altitude Operation WARNING
Engines lose horsepower when operated at high alti-
tude because the air is too thin to burn as much fuel Do not use the cruise control system when driv-
as at sea level. This loss is about three percent for ing conditions do not permit maintaining a con-
each 1000 feet (300 m) altitude above sea level for a stant speed, such as in heavy traffic or on roads
naturally aspirated engine. that are winding, icy, snow-covered, slippery, or
roads with a loose driving surface. Failure to fol-
All Business Class M2 engines are altitude- low this precaution could cause a collision or
compensated by the use of a turbocharger. This re- loss of vehicle control, possibly resulting in per-
duces smoky exhaust at high altitudes, requires less sonal injury or property damage.
downshifting, and allows the engine to make better
use of its fuel. Nevertheless, shift gears as needed to Dash-Mounted Switches
avoid excessive exhaust smoke.
Engine Shutdown NOTICE

1. With the vehicle stopped, apply the parking When the cruise control is engaged, do not at-
brake, and place the transmission in neutral. tempt to shift gears without using the clutch
pedal. Failure to follow this precaution will result
in a temporarily uncontrolled increase in engine
NOTICE speed. Transmission damage and gear stripping
could result.
Idle the engine one to two minutes before shut-
ting it down. After hard operation, shutting down Cruise control is activated by two dash-mounted
the engine without idling may cause damage to switches (Fig. 7.15).
the turbocharger. • On/Off Switch—this two-position rocker is la-
2. Allow the engine to idle one to two minutes be- beled SPD CNTL on the lower half of the
fore shutting it down. This allows the lubricating switch. When cruise control is on, an amber
oil and the coolant to carry heat away from the light illuminates the top part of the switch.
combustion chambers, bearings, shafts, and • Set/Resume Switch—this three-position paddle
seals. The extreme heat may cause bearings to switch is labeled RES/ACC above the paddle
seize or oil seals to leak. and SET/CST below the paddle.
IMPORTANT: Bearings and seals in the turbo- 1. To cruise at a particular speed:
charger are subjected to the high heat of com-
bustion exhaust gases. While the engine is run- 1.1 Press the upper half of the On/Off switch.
7.11
Truck-Manuals.net
Engines
3. To resume a preselected cruise speed:

3.1 Ensure the cruise control is on.
3.2 Momentarily raise the paddle of the Set/
Resume switch. Cruise will return to the
1 last speed selected.
NOTE: If vehicle speed drops below the
minimum cruise control speed, cruise control
will disengage. To resume to the preselected
cruise speed, increase vehicle speed to
above minimum cruise control speed and
press the ACC/RES button.
NOTE: The speed memory is lost whenever the
ignition is turned off or the cruise control switch
2
is toggled to Off.
4. To increase cruise speed, raise and hold the
paddle of the Set/Resume switch until the vehicle
09/13/2001 f610510 accelerates to the desired speed.
To turn cruise control on, press the upper half of the On/
Off switch. To turn cruise control off, press the lower half 5. To decrease cruise speed, lower and the paddle
of the On/Off switch. of the Set/Resume switch until the vehicle decel-
erates to the desired speed.
To increase cruise speed, raise and hold the paddle of
the Set/Resume switch to RES/ACC until the vehicle
accelerates to the desired speed. To decrease cruise Shift Knob Controls, Optional
speed, lower and the paddle of the Set/Resume switch to Cruise control can also be activated by the optional
SET/CST until the vehicle decelerates to the desired
speed.
PAUSE, RESUME, and SET buttons on the transmis-
sion shift knob (Fig. 7.16).
1. Cruise Control On/Off Switch
2. Cruise Control Set/Resume Switch
Fig. 7.15, Cruise Control Switches
1.2 Depress the accelerator pedal until the

speedometer reaches the desired speed.
1.3 Momentarily lower the paddle of the Set/
Resume switch to set the desired speed.
NOTE: The speed memory is lost whenever the
ignition switch is turned to OFF, or cruise control
is turned off.
2. To disengage the cruise control, do one of the
following:
05/23/95 f260316
• Press the lower half of the on/off switch
button. Fig. 7.16, Cruise Control Buttons on the Transmission
• Depress the brake pedal. Shift Knob
• Depress the clutch pedal (on a manual 1. To cruise at a particular speed, do these steps:
transmission only). 1.1 Hold the accelerator pedal down until the
speedometer reaches the desired speed.
7.12
Truck-Manuals.net
Engines
1.2 Push the SET button on the transmission NOTE: Do not attempt to change gears while
shift knob. the vehicle is moving. The transmission will ig-
2. To disengage the cruise control, do these steps: nore the request.
2.1 Press down the brake pedal (on automatic 5. To end the mobile mode, bring the vehicle to a
and manual transmission) or stop. The clutch will open and shut down power
to the PTO.
Press down the clutch pedal (on manual
transmission only) 6. To resume stationary mode, shift to neutral. The
PTO will engage.
2.2 Push the PAUSE button on the transmis-
sion shift knob. 7. To end stationary mode, press the dash switch.
When the light in the switch goes out, power to
3. To resume a preselected cruise speed, push the the PTO is shut off.
RESUME button on the transmission shift knob.
Cruise will return to the last speed selected.
Engine Braking
NOTE: If the ignition is shut off, the speed
memory will be lost. Each engine manufacturer uses a specific engine
brake for their engine. Regardless of the manufac-
4. To adjust cruise speed up, push the SET button turer, the engine brake is operated with the principles
and hold it in until the vehicle accelerates to the outlined in this chapter. Refer to the engine manufac-
desired speed. turer’s operation manual for details of their particular
5. To adjust cruise speed down, push the RESUME engine brake product.
button and hold it in until the vehicle decelerates
to the desired speed. WARNING
To avoid injury from loss of vehicle control, do
Power Takeoff (PTO) Governor not activate the engine brake system under the
Engine power takeoffs (PTO) are devices used to tap following conditions:
into engine power to run auxiliary devices, such as • on wet or slippery pavement, unless the
hydraulic pumps that power additional equipment. vehicle is equipped with antilock braking
The following instructions are general guidelines for system (ABS) and you have had prior expe-
operating a PTO. rience driving under these conditions;
1. Set the parking brake and put the transmission in • when driving without a trailer or pulling an
neutral. empty trailer;
2. Press the dash-mounted PTO switch. Release • if the tractor drive wheels begin to lock, or
the switch when the amber light behind the there is fishtail motion after the engine
switch begins to blink. brake is activated.
When the light is steadily illuminated, the PTO is Whenever vehicle braking is required on good road
engaged and ready to operate. In stationary conditions, the engine brake may be used in con-
mode, the vehicle must remain in neutral with the junction with the service brakes. There is no time
parking brake set. limit for operation of the engine brake. However, an
3. To activate the mobile mode, shift from neutral to engine brake does not provide the precise control of,
reverse, 1st, or 2nd gear. The clutch will open and is not a substitute for, service brakes.
and the PTO will disengage for a moment.
4. Touch the throttle pedal to close the clutch and WARNING
engage the PTO in mobile mode. The PTO may
be operated with the transmission in reverse, Usage of the engine brake as the primary braking
neutral, 1st, or 2nd gears only. system can cause unpredictable stopping dis-
tances, that could result in personal injury or
7.13
Truck-Manuals.net
Engines
property damage. Service brakes are the primary The control speed varies, depending on vehicle
vehicle braking system. weight and the downhill grade.
Two dash-mounted switches control the engine For faster descent, select a higher gear than that
brake: used for control speed. Service brakes must then be
used intermittently to prevent engine overspeed and
• The On/Off switch (ENG BRK), is used to turn
to maintain desired vehicle speed.
the engine brake on and off. See Fig. 7.17.
When the engine brake is on, an amber light For slower descent, select a lower gear, being care-
will illuminate behind the switch. ful not to overspeed the engine. Occasional deactiva-
tion of the engine brake may be necessary to main-
• The engine brake intensity switch (HI/MED/LO
tain the designated road speed under these
or, in some cases, HI/LO) controls the amount conditions.
of engine braking. When the panel lights are
on, the ENG BRK legend is backlit in green. If the engine is equipped with both cruise control and
an engine brake, the engine brake can operate auto-
matically while in cruise control mode. If the cruise
1 2 control/engine brake function is turned on in the
DDEC VI system programming, the engine brake will
come on low when the set road speed increases a
few mph (km/h) above the cruise set speed. The
maximum amount of braking is selected with the
dash switches. When the vehicle returns to the set
cruise speed, the engine brake will turn off.
The engine brake will only operate when the accel-
erator pedal is fully released. Depressing the clutch
will also prevent the engine brake from operating.
10/17/2001 f610588
Vehicles equipped with ABS have the ability to turn
1. Engine Brake On/Off
2. Engine Brake Intensity Switch the engine brake off if wheel slip is detected. The
engine brake will automatically turn back on once
Fig. 7.17, Engine Brake Switches wheel slip is no longer detected.
Since the engine brake is most effective at rated en- The DDEC VI system will deactivate the engine
gine speed, gear selection is very important. Gearing brake when the engine speed falls below 1000 rpm
down the vehicle within the limits of the rated engine or when the vehicle slows down to a preset speed,
speed makes the engine brake more effective. Rec- depending on DDEC programming. This prevents
ommended engine braking speed is above 1800 rpm stalling the engine.
and below the rated speed.
Engine Brake Operation
WARNING Depending on the brake type, the engine brake may
be disabled when engine temperature falls below a
The engine brake must be disengaged when set level.
shifting gears using the clutch pedal. If the en-
gine brake is engaged when the transmission is
in neutral, the braking power of the engine brake NOTICE
can stall the engine, which could result in loss of
Do not allow the engine to exceed 2500 rpm. Se-
vehicle control, possibly causing personal injury
rious engine damage could result.
and property damage.
To activate the engine brake after the engine is
"Control speed" is the speed at which the engine warmed up and the vehicle is in motion:
brake performs 100 percent of the required downhill
braking, resulting in a constant speed of descent. 1. Remove your feet from both the clutch and
throttle pedals.
7.14
Truck-Manuals.net
Engines
2. Press the On/Off switch to toggle the engine

brake on. See Fig. 7.17. The engine brake will
engage at the rate last set on the brake intensity
switch.
3. Move the intensity switch to the desired intensity.
On vehicles with a HI/MED/LO intensity switch,
LO will provide 1/3 of the full braking capacity of
the engine, MED will provide 2/3 of the full brak-
ing capacity, and HI will provide maximum engine
braking. On vehicles with a HI/LO intensity
switch, LO will provide ½ of the full braking ca-
11/28/2001 f610589
pacity of the engine; HI will provide maximum
engine braking. Fig. 7.18, Exhaust Brake Switch
4. Use the intensity switch set at the LO position
when driving on flat, open stretches of road. If
the service brakes are still required to slow down
on a grade, switch to a higher setting on the
dash switch until there is no need for the service
brakes. Grade descent speed should be such
that the service brakes are used infrequently and
remain cool, thus retaining their effectiveness.
5. For maximum retarding, maintain the top gov-
erned speed of the engine through the appropri-
ate selection of gears. When shifting gears, the
engine brake will disengage when the clutch
03/31/2009 f610589a
pedal is depressed, then engage when the clutch
pedal is released. Fig. 7.19, Exhaust Brake Switch
6. To cancel the engine brake application, toggle
the On/Off to off. brake system. The exhaust brake can be used alone
or together with the constant-throttle valves for steep
or long grades. The exhaust brake switch located on
Exhaust Braking Systems the control panel, in combination with the accelerator
and clutch pedals, allows the driver to make maxi-
Exhaust Brake Switch mum use of the exhaust brake in off-highway and
The optional exhaust brake is controlled by a dash- mountain driving as well as in traffic or high-speed
mounted rocker switch to help slow the vehicle when highway driving.
the accelerator is released. When only the exhaust brake is installed, a two-
To turn the exhaust brake on, press on the upper position switch on the dash controls the engine brak-
part of the rocker (at the light inside the switch). The ing system. The exhaust brake is only active when
exhaust brake turns off automatically. See Fig. 7.18 the engine speed is between 1100 and 2700 rpm.
or Fig. 7.19. Depressing the accelerator or clutch pedal deacti-
vates the exhaust brake. The ABS system, when ac-
When the exhaust brake switch is on, an amber LED tive, also deactivates the exhaust brake.
illuminates inside the switch. When the panel lights
are on, the EXHST BRK legend is backlit in green. The exhaust brake is a butterfly valve mounted in the
exhaust pipe. When the driver’s foot is not on the
Mercedes-Benz Exhaust Brake accelerator pedal and the upper half of the exhaust
brake switch is pressed in, with the amber light on
An exhaust brake is an optional auxiliary braking sys- the switch illuminated, an air cylinder shuts the but-
tem that assists but does not replace the service terfly valve, which restricts the flow of exhaust gases
7.15
Truck-Manuals.net
Engines
and retards the engine. This retarding action is car- The retarding force of the brake may not al-
ried through the engine and drivetrain, slowing the ways be noticed, but it is actually preventing
vehicle and reducing the need for frequent service the vehicle from going much faster.
brake applications.
Make sure the exhaust brake is turned off before
Exhaust brakes are not intended for use as the pri- shutting down the engine.
mary braking system during vehicle operation.
Driving Downhill
Operating Characteristics
While approaching a steep grade, make sure that the
upper half of the exhaust brake switch is pressed in,
WARNING with the amber light illuminated. The exhaust brake
comes on as soon as you remove your foot from the
Do not use the exhaust brake when driving on accelerator pedal. While going down the grade, use
slippery or low-traction road surfaces. Failure to a low enough gear to safely descend with a minimum
follow this precaution could result in a loss of application of the service brakes. As a general guide-
vehicle control and possible personal injury or line, use the same gear as you would to ascend the
property damage. hill.
Before starting the engine, make sure that the lower
half of the exhaust brake switch is pressed in and NOTICE
the amber light is not illuminated. Do not turn the ex-
haust brake on until the engine has reached normal Do not allow the engine to exceed its governed
operating temperatures. speed, or serious engine damage could result.
When you remove your feet from both the accelera- Apply the service brakes to reduce the engine rpm or
tor and clutch pedals and the upper half of the ex- make a slower descent by using a lower gear.
haust brake switch is pressed in with the amber light
illuminated, the exhaust brake is applied. The follow- Pacbrake® Exhaust Brake
ing conditions should exist if the brake is operating
properly: The Pacbrake exhaust brake is intended as a
supplement to the service brakes and will not bring
• A slight change in the sound of the engine may the vehicle to a complete stop. The Pacbrake will
be noticed when the exhaust brake is applied. assist in the control or reduction of road speed in
• Exhaust smoke should appear normal. conjunction with, or independent of, the service
brakes. The amount of retarding or braking force is
• Engine temperature should remain in the nor- controlled by the driver.
mal operating range.
• Road speed usually decreases when the ex- Pacbrake Operation (Caterpillar)
haust brake is applied during a descent. When The Pacbrake is controlled by the exhaust brake
the vehicle is carrying a heavy load or the switch and the throttle pedal. All applications are ad-
grade is extremely steep, you may need to ditionally affected, controlled, or governed by engine
apply the service brakes occasionally. speed through transmission gear selection. The Alli-
• Do not expect a retarding effect similar to sud- son MD3060 transmission has automatic downshift-
den hard application of the service brakes. The ing when the exhaust brake is requested. See the
exhaust brake retards the vehicle with a information on the "Allison World Transmission" later
smooth braking effect. in this chapter.
• During a descent, the tachometer usually On some applications, when the Pacbrake is in use,
shows a drop in rpm, depending on the grade it may be necessary to check that the cruise control
and the vehicle load. is not set and that the throttle is in the idle position.
• Depending on the grade and vehicle load, you On some applications, the engine, transmission,
may or may not feel the retarding force acting cruise control, and the Pacbrake exhaust brake may
against your body when the brake is applied.
7.16
Truck-Manuals.net
Engines
electronically interact with each other, which auto-

matically operates their functions. Following are A
A
some examples of the programmed options that may
be available with the cruise control in the on position: A
• The coast mode engages the Pacbrake when

the service brake is applied and disengages
when the service brake is released.
• The latch mode engages the Pacbrake when
the service brake is applied and the Pacbrake
remains on after the service brake is released.
The Pacbrake is disengaged when another
input (depressing the throttle or clutch, engine
speed drops below 800 rpm, or the exhaust 03/06/2000 f490228
brake switch is turned off) is supplied. A. Lubrication Point
• The manual mode does not require the cruise
Fig. 7.20, Pacbrake Exhaust Brake and Air Cylinder
control switch to be on, and operates the
Pacbrake manually at the driver’s discretion. causing corrosion in an improperly functioning
The amount of braking power the engine will develop or nonfunctioning brake. If it is necessary to pe-
is related to the speed (rpm) of the engine. The riodically start the engine, it is recommended
higher the engine rpm, the greater the retarding that normal operating temperatures be attained
power. before shutting down the engine.
Certain conditions may require that the transmission
be downshifted in order to generate adequate rpm Allison World Transmission
for the amount of retarding power required. Pacbrake Pacbrake exhaust brakes used with the Allison World
exhaust brakes are designed and approved for safe Transmission MD series, are interfaced with the
use at 300 rpm above the engine’s maximum gov- transmission electronic control module (ECM). An
erned rpm. Refer to individual engine manufacturer’s exhaust-brake-enabled transmission ECM will usually
specifications. provide converter lockup in gears two through six.
The Pacbrake will function best if it is used all of the Effective exhaust braking begins when the transmis-
time. However, if the vehicle is used inconsistently or sion automatically downshifts into fifth gear (62 mph
seasonally, it may be necessary to perform a preven- or less). Once on, the Pacbrake exhaust brake will
tive maintenance procedure. control road speed and/or slow the vehicle suffi-
ciently that the transmission will automatically down-
1. With the engine shut down, use any oil-free or shift, if necessary, to Allison’s preselect mode.
nonpetroleum-based high-heat lubricant, and
spray or coat a sufficient amount on the restricter The preselect mode is normally assigned to second
valve shaft and the attaching locations at each gear; however, the transmission can be repro-
end of the actuation cylinder. See Fig. 7.20. grammed by an Allison Transmission Distributor to
third or fourth gear, should the operator desire. If ad-
2. With your hands or a pair of pliers, motion the ditional retarding power is required before the auto-
valve several times to distribute the lubricant matic downshifting occurs, you can select a lower
down the shaft and the attaching locations. transmission gear on the Allison shift selector.
NOTE: Starting the engine and idling for short
periods of time is not recommended. During a
cold engine start-up, enough moisture is devel-
oped within the engine and the exhaust system
to create a corrosion hazard that could affect
the future operation of the Pacbrake. The brake
housing may trap water in the valve shaft bore
7.17
Truck-Manuals.net
8
Drivetrain
Clutches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1
Allison On-Highway Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3
Allison MD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5
Eaton® Fuller® Straight-Shift Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8
Eaton Fuller Range-Shift Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.9
Eaton Fuller AutoShift™ Automated Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.12
Freightliner SmartShift Shift Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.15
Eaton Fuller UltraShift Automated Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.15
Eaton Fuller UltraShift PLUS Automated Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.21
Mercedes-Benz Manual Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.25
Mercedes-Benz Automated Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.26
Meritor™ Drive Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.30
Truck-Manuals.net
Drivetrain
Clutches Holding the Vehicle on an Incline With a

Slipping Clutch
Clutch Operation
A slipping clutch accumulates heat faster than it can
Applying the Clutch Brake be dissipated, resulting in early clutch failures. Never
The purpose of the clutch brake is to stop the trans- use the clutch to hold a vehicle on a hill.
mission gears from rotating in order to engage the
transmission gears quickly in making an initial start.
Coasting With the Clutch Released
To apply the clutch brake, put the transmission in (pedal down) and the Transmission in
neutral and press the clutch pedal to the floor. Gear
CAUTION WARNING
Never apply the clutch brake while the vehicle is Do not coast with the clutch released (pedal de-
moving. The clutch pedal should never be pressed) and the transmission in gear. High
pressed down fully before putting the transmis- driven-disc rpm could cause the clutch facing to
sion in neutral. Considerable heat will be gener- be thrown off the disc. Flying debris could cause
ated, which will be detrimental to the friction injury to persons in the cab.
discs, release bearings, and transmission front If the transmission remains in a low gear and the ve-
bearings. hicle gains speed, as may occur on a downgrade,
Applying the clutch brake with the transmission still in the input shaft and clutch driven disc will turn at
gear puts a reverse load on the gear. At the same speeds that are higher than normal. This occurs be-
time, it will have the effect of trying to stop or decel- cause the rear wheels and the driveline become the
erate the vehicle with the clutch brake. Rapid wear of input for the transmission, and a higher-than-normal
friction discs will take place necessitating frequent re- speed for a given transmission gear translates to a
placement. higher rpm value for the clutch driven disc.
Clutch driven discs are designed to allow for some
Vehicle Overload, or Overloading the amount of excess rotational speed, but the facing
Clutch has a limited burst strength. If the clutch driven disc
rpm increases too much, the clutch facing can be
CAUTION thrown off the disc(s).
Overloading will not only result in damage to the Engaging the Clutch While Coasting
clutch, but also to the entire powertrain.
Engaging the clutch while coasting can result in tre-
Clutches are designed for specific vehicle applica- mendous shock loads and possible damage to the
tions and loads. These limitations should not be ex- clutch as well as to the entire drivetrain.
ceeded.
Report Erratic Clutch Operation Promptly
Riding the Clutch Pedal
Reporting erratic clutch operation as soon as pos-
Riding the clutch pedal is destructive to the clutch. sible will give maintenance personnel a chance to
Partial clutch engagement permits slippage, and gen- inspect the clutch components.
erates excessive heat. Riding the clutch pedal will
also put a constant thrust load on the release bear- CAUTION
ing, which can thin out the lubricant. Release bearing
failures can be attributed to this type of misuse. Operating the vehicle with incorrect clutch pedal
free-travel could result in clutch damage. See
Group 25 of the Business Class® M2 Workshop
Manual for free-pedal adjustment procedures and
specifications.
8.1
Truck-Manuals.net
Drivetrain
On mechanical clutch linkages, free-pedal travel Clutch Lubrication

should be included and commented on daily in the
driver’s report, since clutch free-pedal travel is the The release bearing should be lubricated at frequent
best guide to the condition of the clutch and the re- intervals. See Group 25 of the Business Class® M2
lease mechanism. Maintenance Manual for intervals and procedures.
Clutch Wear CAUTION

The major reason clutches wear out too soon is ex-
Failure to lubricate the release bearing as recom-
cessive heat. Clutches are designed to absorb and
mended could result in release bearing damage
dissipate more heat than encountered in typical op-
and damage to the clutch.
eration. The temperatures developed in typical op-
eration will not break down the clutch friction sur- NOTE: The Sachs hydraulic clutch does not re-
faces. However, if a clutch is slipped excessively or quire lubrication of the release bearing.
required to do the job of a fluid coupling, high tem-
peratures develop quickly and destroy the clutch. Sachs Hydraulic Clutch
Temperatures generated between the flywheel,
driven discs, and pressure plates can be high The Sachs hydraulic clutch is a 14.5-inch (365 mm)
enough to cause the metal to flow and the friction push-type clutch that is used with the Mercedes-
facing material to char and burn. Benz medium-duty transmissions, models MBT520
and MBT660.
CAUTION NOTE: All Mercedes-Benz transmission models
require a hydraulic clutch system. For more in-
Do not allow sustained slippage of the clutch; formation on the Mercedes-Benz transmissions,
this could severely damage the clutch disc, pres-
see under the heading "Mercedes-Benz Manual
sure plate, or flywheel. Damage caused by clutch
slippage due to improper break-in is not warrant- Transmissions."
able. The clutch hydraulic system consists of three main
Slipping and excessive heat are practically nonexis- components:
tent when a clutch is fully engaged. But during the • A pedal unit, including the pedal, master cylin-
moment of engagement, when the clutch is picking der and fluid reservoir,
up the load, it generates considerable heat. An incor-
rectly adjusted or slipping clutch will rapidly generate • A slave cylinder at the clutch,
sufficient heat to destroy itself. • A hydraulic hose that connects the master and
The most important items that a driver should be slave cylinders.
aware of to ensure long service life of the clutch in- Keep the clutch fluid reservoir full to the MAX mark.
clude: starting in the right gear, recognizing clutch If fluid level falls below the MIN mark, have the hy-
malfunctions, and knowing when to adjust a clutch. draulic system checked for leaks at an authorized
Freightliner service facility. Use only DOT 4 brake
Clutch Adjustments fluid to fill the reservoir.
Some clutches have an internal adjustment. See the The hydraulic clutch provides smooth, quiet, and reli-
applicable section in Group 25 of the Business able clutch actuation with a minimum of mainte-
Class® M2 Workshop Manual for clutch adjustment nance.
procedures and specifications.
Pressure builds up in the master cylinder when the
clutch pedal is pressed. This pressure is transmitted
CAUTION through the brake fluid in the hose to the slave cylin-
der, where it acts directly on the clutch release fork.
Operating the vehicle with the clutch incorrectly
adjusted could result in clutch or clutch brake
failure.
8.2
Truck-Manuals.net
Drivetrain
Allison On-Highway 6. Chock the rear tires and take any other steps
necessary to keep the vehicle from moving.
Transmissions
2000 Series
The Allison on-highway transmissions are fully auto-
matic and include the 1000 Series™, 2000 Series™, On vehicles with Allison 2000 series transmissions,
and 2400 Series™. Refer to the Allison website for do the following steps if you have to leave the cab
additional information, www.allisontransmission- with the engine running (for example, when checking
.com. the transmission fluid):
Safety Precautions Without Auto-Apply Parking Brake

Follow the instructions for vehicles with 1000 series
WARNING transmissions, under the heading "Without Park Posi-
tion."
Do not leave the vehicle unattended with the en-
gine running. If you leave the vehicle and the en- With Auto-Apply Parking Brake
gine is running, the vehicle can move suddenly, 1. Bring the vehicle to a complete stop using the
which could result in personal injury or property service brake.
damage.
2. Ensure that the engine is at low idle rpm.
1000 Series 3. Put the transmission in PB (auto-apply parking
On vehicles with Allison 1000 series transmissions, brake).
do the following steps if you have to leave the cab 4. Apply the parking brake (if equipped), and make
with the engine running (for example, when checking sure it is properly engaged.
the transmission fluid):
5. Chock the rear tires and take any other steps
Without Park Position necessary to keep the vehicle from moving.
1. Bring the vehicle to a complete stop using the 2400 Series
service brake.
On vehicles with 2400 series transmissions, follow
2. Ensure that the engine is at low idle rpm. the instructions for vehicles with 1000 series trans-
3. Put the transmission in neutral. missions.
4. Apply the parking brake, and make sure it is
properly engaged.
Range Inhibit Indicator, 2000 and
2400 Series
5. Chock the rear tires and take any other steps
necessary to keep the vehicle from moving. A RANGE INHIBIT indicator is a standard feature of
the 2000 series and 2400 series transmissions. The
With Park Position RANGE INHIBIT indicator comes on to alert the
driver that transmission operation is being inhibited
1. Bring the vehicle to a complete stop using the and that the range shifts being requested by the
service brake. driver may not occur. When certain operating condi-
2. Ensure that the engine is at low idle rpm. tions are detected by the TCM (transmission control
module), the controls will lock the transmission in the
3. Put the transmission in P (park). current operating range.
4. Apply the parking brake (if equipped), and make Shift inhibits occur under the following conditions:
sure it is properly engaged.
• Shifts from neutral to reverse or from neutral to
5. Engage the park range by slowly releasing the a forward range when the engine is above idle,
service brake. greater than 900 rpm.
8.3
Truck-Manuals.net
Drivetrain
• Forward/reverse directional shifts are typically Do not idle in reverse for more than 5 minutes. Se-
not permitted if appreciable output shaft speed lect P (park), PB (auto-apply parking brake), or N
is detected. (neutral) when time at idle exceeds 5 minutes.
• When some types of unusual transmission op- NOTE: The shift into reverse may not succeed if
erating conditions are detected by the TCM, a range inhibitor is active. Check for illumination
the TCM temporarily limits transmission opera- of the RANGE INHIBIT indicator.
tion until the vehicle can be driven to a service
location. When this type of situation is de- N (Neutral)
tected, the TCM will lock the transmission in a
safe gear range. The neutral position places the transmission in neu-
tral. This position is used when starting the engine
• The TCM will prevent shifts from park or neu- and for stationary operation.
tral to range when auxiliary equipment, such as
a power takeoff unit (PTO), is in operation.
WARNING
Operating Instructions, On-Highway Failure to apply the vehicle parking brakes when
Transmissions the transmission is in neutral may allow the ve-
hicle to move unexpectedly, possibly causing
Allison automatic transmissions are electronically
property damage or personal injury.
controlled. The shift selector provides five or six for-
ward ranges and one reverse range. When neutral is selected, the vehicle service brakes,
parking brake, or emergency brake must be applied.
P (Park, optional on 1000 and 2400 Selecting neutral does not apply vehicle brakes un-
Series) less an auxiliary system to apply the parking brake is
installed.
Use park when turning the engine on or off, to check
vehicle accessories, to operate the engine in idle for
longer than 5 minutes, and for stationary operation of WARNING
the power takeoff, if equipped. This position places
the transmission in neutral and engages the park Do not coast in neutral. Coasting in neutral can
pawl of the transmission. cause an accident, possibly resulting in severe
personal injury or death.
NOTE: This does not apply the parking brake.
Do not let the vehicle coast in neutral. If the vehicle
PB (Auto-Apply Parking Brake, optional is allowed to coast in neutral, the engine brake will
not work and you could lose control of the vehicle.
on 2000 Series)
The auto-apply parking brake places the transmis- CAUTION
sion in neutral and applies the parking brake.
Coasting in neutral can cause severe transmis-
R (Reverse) sion damage.
Reverse is used to back the vehicle. When the selec-
D (Drive)
tor is in reverse, the reverse warning signal will
sound. Always bring the vehicle to a complete stop
before shifting from a forward range to reverse, or WARNING
from reverse to a forward range.
When going downhill, use a combination of
downshifting, braking, and other retarding de-
CAUTION vices to control vehicle speed and the engine’s
rated governed speed. Failure to do so could re-
Extended idling in reverse may cause transmis-
duce vehicle braking, possibly causing loss of
sion overheating and damage.
vehicle control and resulting in personal injury or
property damage.
8.4
Truck-Manuals.net
Drivetrain
In the drive position, the transmission will initially go

into first range when drive is selected. As vehicle
Allison MD Series
speed increases, the transmission will upshift auto- Refer to the Allison website for additional information,
matically through each available range up to fourth www.allisontransmission.com.
range or fifth range. As the vehicle slows, the trans-
mission will downshift automatically. Safety Precautions
When going downhill, downshift to a lower transmis-
sion range to increase engine braking and to help WARNING
maintain control. The transmission has a feature to
prevent automatic upshifting above the lower range Do not leave the vehicle unattended with the en-
selected. However, during downhill operation, the gine running. If you leave the vehicle and the en-
transmission may upshift to the next higher range, if gine is running, the vehicle can move suddenly,
the engine is exceeding its governed speed in the which could result in personal injury or property
lower range. damage.
On vehicles with MD series transmissions, do the
CAUTION following steps if you have to leave the cab with the
engine running (for example, when checking the
Do not idle in drive for more than 5 minutes. Ex- transmission fluid):
tended idling in drive may cause transmission
overheating and damage. Always select PB (auto- 1. Bring the vehicle to a complete stop using the
apply parking brake) or P (park) if time at idle is service brake.
longer than 5 minutes. 2. Put the transmission in N (neutral).
NOTE: The shift into drive may not succeed if a 3. Ensure that the engine is at low idle (500 to 800
range inhibitor is active. Check for illumination rpm).
of the RANGE INHIBIT indicator.
4. Apply the parking brake and emergency brakes,
4 and 3 (Fourth and Third Ranges, and make sure they are properly engaged.
optional) 5. Chock the rear tires and take any other steps
necessary to keep the vehicle from moving.
Use the fourth or third range for city traffic and for
braking on steep downgrades. Operating Instructions, MD Series
3 and 2 (Third and Second Ranges, The Allison MD transmission is electronically con-
standard) trolled and comes with a push-button shift control
that provides five or six forward ranges and one re-
Use the third or second range for heavy city traffic verse range. The push-button shift selector has an R
and for braking on steeper downgrades. (reverse), an N (neutral), a D (drive), an up arrow, a
down arrow, a mode button, and a digital display.
1 (First Range)
New shift controls — known as "fourth generation" —
Use first range when pulling through mud or deep were introduced in mid-2006. They replaced the pre-
snow, when maneuvering in tight spaces, or when vious units that are commonly referred to as "WTEC
driving up or down very steep grades. First range III". See Fig. 8.1 and Fig. 8.2.
provides the vehicle with its maximum driving torque
and maximum engine braking effect. R (Reverse)
NOTE: To have the transmission select these Press the R button to select reverse. The digital dis-
ranges automatically, leave the selector lever in play will show R when reverse is selected. Always
D (drive). bring the vehicle to a complete stop and let the en-
gine return to idle before shifting from a forward
range to reverse, or from reverse to a forward range.
8.5
Truck-Manuals.net
Drivetrain
NOTE: The shift into reverse may not succeed if

1
a range inhibitor is active. When reverse is se-
2 lected, always be sure that R is not flashing.
3
N (Neutral)
R WARNING
4
N
When starting the engine, make sure that the ser-
D vice brakes are applied. Failure to apply the ser-
vice brakes may result in unexpected vehicle
movement, which could cause severe personal
injury or death. Failure to apply the vehicle park-
07/27/2006 f270113
ing brakes when the transmission is in neutral
1. Digital Display 3. Mode Indicator LED may allow the vehicle to move unexpectedly, pos-
2. Mode Identification 4. Mode Button sibly causing property damage or personal injury.
Label
Press the N button to select neutral. The digital dis-
Fig. 8.1, WTEC III Push-Button Shift Selector play will display N when neutral is selected. It is not
necessary to press neutral before starting the ve-
hicle. The ECU (electronic control unit) or TCM
(transmission control module) automatically places
the transmission in neutral at start-up.
1
2
WARNING
3
Failure to apply the vehicle parking brakes when
4
the transmission is in neutral may allow the ve-
hicle to move unexpectedly, possibly causing
property damage or personal injury.
When neutral is selected, the vehicle service brakes,
parking brake, or emergency brake must be applied.
Selecting neutral does not apply vehicle brakes un-
less an auxiliary system to apply the parking brake is
installed.
07/27/2006 f610804
1. Digital Display
2. Mode Identification
3. Mode Indicator LED
4. Mode Button
WARNING
Label
Do not coast in neutral. Coasting in neutral can
Fig. 8.2, Fourth Generation Push-Button Shift Selector cause an accident, possibly resulting in severe
personal injury or death.
CAUTION Do not let the vehicle coast in neutral. If the vehicle

is allowed to coast in neutral, the engine brake will
Extended idling in reverse may cause transmis- not work and you could lose control of the vehicle.
sion overheating and damage. Always select neutral before turning off the engine.
Do not idle in reverse for more than 5 minutes. Se- Neutral is also used during stationary operation of
lect neutral when time at idle exceeds 5 minutes. the power takeoff if your vehicle is equipped with a
PTO.
8.6
Truck-Manuals.net
Drivetrain
D (Drive) engine governed speed is exceeded in the lower

range, the transmission may upshift to the next
When the D button is pushed, the highest forward higher range.
range will appear in the display. The transmission will
normally go into first range when drive is selected 1 (First Range)
(except for those units programmed to start in sec-
ond range). As vehicle speed increases, the trans- Use the first range when pulling through mud or
mission will upshift automatically through each range. deep snow, when maneuvering in tight spaces, or
As the vehicle slows, the transmission will downshift when driving up or down steep grades. First range
automatically. provides the vehicle with its maximum driving torque
and maximum engine braking effect. Push the down
arrow until the first range appears on the display.
CAUTION
Do not idle in drive for more than 5 minutes. Ex-
Up and Down Arrows
tended idling in drive may cause transmission When a lower range is desired, after D has been
overheating and damage. Always select neutral if pressed, press the down arrow until the desired
time at idle is longer than 5 minutes. range is shown on the display. Pressing the down
arrow continuously causes the range position to con-
NOTE: The shift into drive may not succeed if a tinue to go down until the button is released or the
range inhibitor is active. When drive is selected, lowest range is attained.
always be sure that D is not flashing.
When the transmission is in drive and the down
5, 4, 3, and 2 (Fifth, Fourth, Third, and arrow has the transmission in a lower range position,
Second Ranges) press the up arrow to shift to a higher selector posi-
tion. Pressing the up arrow continuously causes the
Occasionally, road conditions, load, or traffic condi- range position to continue to rise until the button is
tions will make it desirable to restrict automatic shift- released or the highest available position is attained.
ing to a lower range. Lower ranges provide greater
braking for going down grades. The lower the range, Pressing the up or down arrows does not override
the greater the braking effect. the transmission automatic shifting operation. If a
higher or lower position is selected, the transmission
Push the up or down arrows on the push-button shift continues shifting through the ranges according to
selector to select individual forward ranges. The digi- the vehicle operating characteristics until the highest
tal display will display your choice of range. When a or lowest selected position is reached.
lower range is selected, the transmission may not
downshift until the vehicle speed or engine RPM (en- Mode Button
gine governed speed) is reduced.
The MODE button starts a specialized input or output
function that has been previously programmed into
WARNING the ECU or TCM. Pressing the MODE button
changes transmission operation for a specific func-
When going downhill, use a combination of tion.
downshifting, braking, and other retarding de-
vices to control vehicle speed and the engine’s Mode Indicator LED
rated governed speed. Failure to do so could re-
duce vehicle braking, possibly causing loss of When the MODE button is pressed, the mode indica-
vehicle control and resulting in personal injury or tor LED illuminates. A mode identification label, lo-
property damage. cated above the MODE button, identifies the function
associated with a mode change.
When going downhill, downshift to a lower transmis-
sion range to increase engine braking and to help
maintain control. The transmission has a feature to
prevent automatic upshifting above the lower range
selected. However, during downhill operation, if the
8.7
Truck-Manuals.net
Drivetrain
Digital Display General Information, Straight-Shift

The dual digital display shows both the selected Eaton Fuller 5-speed FS models are fully synchro-
range (SELECT) and actual range attained (MONI- nized. They have five forward speeds and one re-
TOR). The single digital display shows the selected verse. See Fig. 8.3 for the shift pattern.
range.
Oil Level Sensor

Allison MD Series transmissions have an electronic R 2 4
oil level sensor to read fluid level information. The
fluid level diagnostic will display whether the oil level N
is OK, too low, or too high. It will also display a de-
fault code and indicate if the preconditions (of receiv-
ing the fluid level information) are not met. 1 3 5
IMPORTANT: Maintain the the proper fluid level
05/21/2008 f261049
at all times. If the fluid level is too low, the con-
verter and clutch do not receive an adequate Fig. 8.3, Shift Pattern, 5-Speed FS Models
supply of fluid. If the level is too high, the trans-
mission may shift erratically or overheat. Eaton Fuller 6-speed FS and FSO models are fully
synchronized. They have six forward speeds and one
To access the oil level display mode, park the vehicle reverse. See Fig. 8.4 for the shift pattern.
on a level surface, shift to N (Neutral), apply the
parking brake, and idle the engine. Then simultane-
ously press both the up and down arrows once. The
oil level will display at the end of a two-minute count-
down.
R 1 3 5
Diagnostic Codes N
Diagnostic codes are numerical indications relating to
a malfunction in transmission operation. These codes 2 4 6
are logged in the TCM/ECU memory. The most se-
vere or most recent code is listed first. A maximum of 05/21/2008 f261048
five codes (numbered d1-d5) may be listed in
memory at one time. If the mode indicator LED is Fig. 8.4, Shift Pattern, 6-Speed FS and FSO Models
illuminated, the displayed code is active. If it is not
illuminated, the displayed code is not active. Eaton Fuller 7-speed T models are not synchronized.
They have seven forward speeds and one reverse.
NOTE: During normal operation, an illuminated See Fig. 8.5 for the shift pattern.
mode indicator LED signifies the specialized
mode operation is in use. These transmissions are designed for use with on-
highway, fuel economy engines where a minimum of
To enter diagnostics mode, first park the vehicle and shifting is desired and less gear reduction is accept-
apply the parking brake. Then simultaneously press able.
both the up and down arrows twice.
Operation, Straight-Shift
Eaton® Fuller® Straight-Shift 1. Always use first gear when starting to move the
Transmissions vehicle forward.
Refer to the Eaton website for additional information, IMPORTANT: Do not rest your foot on the clutch
www.roadranger.com. pedal while driving. This causes partial clutch
8.8
Truck-Manuals.net
Drivetrain
4.2 On synchronized models, disengage the

clutch and move the shift lever to the next
6 lower gear.
R 2 4
On unsynchronized models, disengage the
clutch and move the shift lever to neutral.
N Engage the clutch again. With the shift
lever in neutral, disengage the clutch and
1 3 5 move the shift lever to the next lowest
7 gear.
05/21/2008 f261051 4.3 Engage the clutch smoothly.
Fig. 8.5, Shift Pattern, 7-Speed T Models 4.4 Use the sequence described above to
shift progressively down through each
disengagement which could cause premature successive lower gear, as driving condi-
clutch wear. tions require.
2. On synchronized models, press the clutch pedal
to the floor when shifting gears. Double-clutching Eaton Fuller Range-Shift
is unnecessary. Transmissions
On unsynchronized models, press the clutch Refer to the Eaton website for additional information,
pedal to the floor to contact the clutch brake only www.roadranger.com.
when engaging the first or reverse gears.
NOTE: If the vehicle is moving when shifting, General Information, Range-Shift
press the clutch pedal just far enough to disen- Eaton Fuller 9-Speed Models
gage the clutch. Pressing it to the floor will en-
gage the clutch brake, if so equipped, causing Eaton Fuller 9-speed range-shift models are not syn-
premature clutch brake wear. chronized. They have nine forward speeds and two
reverse speeds. The shift lever controls five forward
3. To upshift, do the following steps: gears and one reverse gear in the transmission front
3.1 Accelerate to engine governed speed. section, and the range lever controls a LO and HI
range in the two-speed auxiliary section. The first
3.2 On synchronized models, disengage the position in the front section is used only as a starting
clutch and move the shift lever to second gear. The other four ratios are used once in LO
gear. range and once again in HI range. See Fig. 8.6 for
On unsynchronized models, disengage the the shift patterns.
clutch and move the shift lever to neutral. After shifting out of the first gear position, use the
Engage the clutch again. With the shift Roadranger® "repeat H" shift pattern. Select both LO
lever in neutral, disengage the clutch and range and HI range with the range lever (range
move the shift lever to second gear. knob). It is used once during the upshift sequence
3.3 Engage the clutch and note the drop in and once during the downshift sequence.
engine rpm before accelerating up to en- Always preselect the range shift. After preselection,
gine governed speed again. the transmission will automatically make the synchro-
3.4 Continue upshifting using the same se- nizer range shift as the shift lever passes through
quence described in the previous step. neutral.
Follow the pattern on the shift lever.
Eaton Fuller 10-Speed Models
4. To downshift, do the following steps:
Eaton Fuller 10-speed range-shift models are not
4.1 Wait until the engine speed drops to the synchronized. They have ten forward speeds and
rpm noted immediately after the upshift.
8.9
Truck-Manuals.net
Drivetrain
HI
Eaton Fuller Shift Progressions
5 7
1 3 LO Range
LO Model HI Range
Off-Highway On-Highway
R R 5 7
A 1 3 1 3 R
N 9-Speed
Direct or
LOW 6 8
Overdrive 2 4 2 4
6 8 B f260322 f260323 f260324
LO
2 4 R R R
7 9
10-Speed 2 4 2 4
11/23/99 f261047 Direct or 6 8 10
Move the range lever up for HI range, down for LO Overdrive 1 3 5 1 3 5
f260329 f260329 f260330
range.
A. HI Range B. LO Range Table 8.1, Eaton Fuller Shift Progressions
Fig. 8.6, Shift Pattern, 9-Speed Models

When downshifting, the driver preselects the range
two reverse speeds. The shift lever controls five for- lever for LO range and the range shift occurs auto-
ward gears and one reverse gear in the transmission matically during the shift lever movement to the next
front section, and the range lever controls a LO and gear position.
HI range in the two-speed auxiliary section. The five
forward gears selected in LO range are used again Eaton Fuller Deep-Reduction Models
in HI range to provide the 10 progressive forward Eaton Fuller deep-reduction models are not synchro-
gears. See Fig. 8.7 for the shift patterns. See nized. They have a five-speed front section and a
Table 8.1 for the shift progressions. two-speed auxiliary section which has an extra deep
reduction gear. The LO gear in the front section is
HI 7 9 used only as a starting gear. The other four ratios
R are used once in LOW RANGE and once in HIGH
LO 2 4
RANGE giving eight highway ratios. LO-LO is se-
lected by the DEEP REDUCTION lever on the dash-
A board. See Fig. 8.8 for the shift pattern.
N
B R R 5 7
6 8 10
1 3 5 R 1 3
12/15/1999 f261053
N
A. HI Range B. LO Range
Fig. 8.7, Shift Pattern, 10-Speed Models LO 6 8
LO−LO 2 4
Once the highest shift lever position (fifth gear) is
03/12/96 f260123a
reached in LO range, the driver preselects the range
shift lever for HI range. The range shift occurs auto-
Fig. 8.8, Shift Pattern, Deep Reduction
matically as the shift lever is moved from fifth gear
position to the sixth gear position.
Operation, Range-Shift
1. When operating off-highway or under adverse
conditions, always use low gear when starting to
move the vehicle.
8.10
Truck-Manuals.net
Drivetrain
When operating on-highway, with no load or 5. While in the top gear of the low-range shift pat-
under ideal conditions, use first gear when start- tern and ready for the next upshift, flip the range
ing to move the vehicle. preselection lever up into high range. Double-
For all conditions, use the highest gear that is clutch through neutral and shift into the bottom
gear in high range. As the shift lever passes
still low enough to start the vehicle moving with
through neutral, the transmission will automati-
the engine idling and without excessively slipping
cally shift from low range to high range.
the clutch.
6. With the transmission in high range, shift pro-
2. Use the clutch brake to stop gear rotation when
shifting into low (or first) or reverse when the ve- gressively up through each of the high range
hicle is stationary. The clutch brake is applied by gears, double-clutching between shifts.
pressing the clutch pedal all the way to the floor.
Downshifting
For normal upshifts and downshifts, only a partial
disengagement of the clutch is necessary to 1. With the transmission in high range, shift pro-
break engine torque. gressively down to the bottom gear in high
range, double-clutching between shifts.
3. Do not make range shifts with the vehicle moving
in reverse gear. 2. When in the bottom gear of the high-range shift
pattern and ready for the next downshift, push
4. Never attempt to move the range preselection the range preselection lever down into low range.
lever with the gear shift lever in neutral while the Double-clutch through neutral and shift into the
vehicle is moving. Preselection with the range top gear of the low-range shift pattern. As the
preselection lever must be made prior to moving shift lever passes through neutral, the transmis-
the shift lever out of gear into neutral. sion will automatically shift from high range to
5. Do not shift from high range to low range at high low range.
vehicle speeds. 3. With the transmission in low range, downshift
6. Use double-clutching between all upshifts and through the low range gears as conditions re-
downshifts. quire.
Never use the clutch brake when downshifting or
7. After your shifting ability improves, you may want
as a brake to slow the vehicle.
to skip some of the ratios. This may be done
only when operating conditions such as load,
grade, and road speed permit.
Operation, Deep-Reduction Models
Upshifting
Upshifting
1. Position the gear shift lever in neutral. See
1. Position the gear shift lever in neutral. Start the Fig. 8.8 for the shift pattern. Start the engine,
engine and bring the air system pressure up to and bring the air system pressure up to 95 to
100 to 120 psi (689 to 827 kPa). 125 psi (655 to 862 kPa).
2. Position the range preselection lever down into 2. Position the range preselection lever down, into
low range. low range.
3. Press the clutch pedal to the floor. Shift into low NOTE: If conditions are difficult, start out in LO-
or first gear, then engage the clutch with the en- LO. Move the DEEP REDUCTION lever on the
gine at or near idle speed to start the vehicle dashboard to the IN position. Otherwise start
moving. Accelerate to 80 percent of engine gov-
out in LO with the DEEP REDUCTION lever in
erned speed.
the OUT position.
4. Shift progressively up from low or 1st gear to the
top gear in low range, double-clutching between
shifts and accelerating to 80 percent of engine
governed speed.
8.11
Truck-Manuals.net
Drivetrain
3. Depress the clutch pedal to the floor. Shift into gear position and the auxiliary section is in the
LO gear; then, engage the clutch, with the en- low range. Then, move the DEEP REDUCTION
gine at or near idle rpm to start the vehicle mov- lever on the dashboard to the IN position. Imme-
ing. The vehicle will start in LO or LO-LO de- diately release the accelerator, depress the
pending on the DEEP REDUCTION lever clutch pedal once to break torque, engage the
position. clutch, and accelerate. The auxiliary section will
automatically shift from LO to LO-LO when the
4. To upshift if in LO-LO, move the DEEP REDUC- gears reach the same speed.
TION lever to the OUT position and immediately
release the accelerator, depress the clutch pedal
once to break torque, and reengage the clutch. CAUTION
The auxiliary section will shift from LO-LO to LO
when the gears reach the same speed. Never use the clutch brake when downshifting, or
as a brake to slow the vehicle. This will cause
5. Shift progressively upward from LO through 1st, premature clutch brake wear.
2nd, 3rd, and 4th gears while the range prese-
lection lever is in LO. Always double-clutch be-
tween gears. Eaton Fuller AutoShift™
6. When in 4th gear and ready for the next upshift, Automated Transmissions
pull up the range preselection lever and move Refer to the Eaton website for additional information,
the shift lever, double-clutching, to the 5th gear www.roadranger.com.
position. As the shift lever passes through neu-
tral, the auxiliary section will automatically shift IMPORTANT: Before starting the vehicle, always
from low to high range. do the following:
• Be seated in the driver’s seat.
CAUTION
• Place the transmission in neutral.
Never move the shift lever into the LO gear posi- • Set the parking brakes.
tion after high range preselection or anytime the
auxiliary section is in high range. Transmission • Press the clutch pedal (if equipped) down to
damage could result. the floor.
7. Continue upshifting from 5th gear through 8th The AutoShift ASW is an automated 6-speed Eaton
gear, always double-clutching between gears. Fuller transmission. No clutch is necessary to oper-
ate the vehicle.
Downshifting The AutoShift AS2 is a partially automated 10-speed
1. While in high range, move the gear shift lever Eaton Fuller transmission. The driver must use the
from 8th gear through 5th gear as conditions re- clutch and put the transmission in neutral to start and
quire, always double-clutching between gears. stop the vehicle. A push-button shift selector
(Fig. 8.9) is used with AutoShift AS2 and ASW
2. When in 5th gear and ready for the next down- transmissions.
shift, push down the range preselection lever and
move the shift lever to the 4th gear position, IMPORTANT: If you have to leave the cab with
being sure to double-clutch. As the shift lever the engine running:
passes through neutral, the auxiliary section will
automatically shift from high to low range. • Place the transmission in neutral.
3. While in the low range, continue downshifting • Set the parking brakes.
from 4th through LO as conditions require, al- • Chock the tires.
ways double-clutching between gears.
4. Do not downshift into LO-LO from LO unless op-
erating conditions make it necessary. If it is nec-
essary, make sure that the shift lever is in the LO
8.12
Truck-Manuals.net
Drivetrain
• To select drive, press the D button. When drive

is engaged, the telltale LED will light up next to
the D button.
10 1 • To select low gear, press the LOW button.
When low is engaged, the telltale LED will light
up next to the LOW button.
9
2 • To change gears manually, press the MANUAL
button. When the manual mode is engaged,
the telltale LED will light up next to the
MANUAL button.
3
• Use the shift buttons (upshift/downshift) to
change the current starting gear selection in R,
D, and LOW. In MANUAL, the shift buttons can
8
4 be used to select gears.
• In automatic mode, the number of the forward
gear currently engaged appears continually on
the mode indicator when in drive. In MANUAL,
5
the last gear selected appears on the mode
7 indicator.
• If the SERVICE indicator illuminates, take the
6 vehicle as soon as possible to an authorized
Freightliner service facility.
• The mode button is reserved for future use.
IMPORTANT: To prevent engine overspeed, the
transmission software will override both
MANUAL and LOW if necessary. The system
11/14/2001 f261145
will not respond to gear selection requests that
1. Not Used 7. Upshift/Downshift will either overspeed or excessively lug the
2. R (reverse) Arrows engine.
3. N (neutral) 8. SERVICE Light
4. D (drive) 9. Mode Indicator
5. MANUAL Mode 10. Mode Button Automatic Mode
6. Low Gear Hold
The AutoShift AS2 transmission is normally operated
Fig. 8.9, Eaton Push-Button Shift Selector in an automatic mode. To select MANUAL mode,
press the MANUAL button on the push-button shift
Push-Button Shift Selector selector.
Gear information is presented to the driver on the When the transmission is in automatic mode, the
push-button shift selector, usually mounted on the transmission automatically selects and engages the
right-hand control panel. On this display, the informa- gears, although the transmission will respond to up-
tion is presented as follows: shift and downshift requests as though in manual
mode. See the instructions for shifting under heading
• To select neutral, press the N button. When "Manual Mode" below.
neutral is engaged, the telltale LED will light up
next to the N button. Manual Mode
• To select reverse, press the R button. When When the transmission is in manual mode, the driver
reverse is engaged, the telltale LED will light must select the appropriate gear, using the shift but-
up next to the R button. tons on the push-button shift selector.
8.13
Truck-Manuals.net
Drivetrain
To upshift in MANUAL, press the upshift button (up NOTE: Neutral is always available during ve-
arrow), and release. The number of the gear will ap- hicle operation. When in neutral, requests to
pear on the mode indicator. If the requested gear is upshift or to downshift are ignored.
available, the transmission will shift up.
D (Drive)
CAUTION Drive (D) is used for normal highway driving. In drive,
the transmission shifts into the proper gear for start-
Do not attempt to upshift until the vehicle has
ing, and then automatically selects additional gears
reached a sufficient speed. The clutch absorbs
as needed, in a range between the starting gear and
the speed difference by generating heat, which
the highest gear.
causes the clutch to wear out too soon.
Many drivers upshift into the next gear or even skip- To select drive, press the clutch pedal to the floor.
shift into a higher gear before the vehicle has Then press the D button. Slowly release the clutch
reached the correct speed. This type of shifting is pedal and drive the vehicle.
almost as bad as starting off in a gear that is too To start up in a gear other than the normal starting
high. When the engine speed (rpm) and the vehicle gear, push the upshift arrow with D selected, and
speed (mph or km/h) are too far apart, the clutch while the vehicle is stopped.
must absorb the difference in speed by generating
heat. IMPORTANT: AutoShift will not start up in any
gear higher than third gear.
To downshift in MANUAL, press the downshift button
(down arrow), and release. The number of the gear The number of the gear selected will flash on the
will appear on the mode indicator. If the requested auxiliary display until the driver presses the clutch
gear is available, the transmission will shift down. pedal. This gear will be stored in memory as the de-
fault starting gear until a different starting gear is se-
If any requested gear is not available, an audible
lected by the driver, or until the engine is shut down.
warning will sound and the digital display will indicate
that the gear is not available. NOTE: The transmission may be programmed
so that it is not possible to select a starting gear
Selecting Gears other than the preprogrammed starting gear.
R (Reverse)
L (Low)
Reverse (R) is used to back the vehicle. Make sure
the vehicle comes to a full stop and the clutch pedal LOW is used to hold the transmission in low gear
has been pressed before shifting into reverse. when descending steep hills. If LOW is selected
when the vehicle is stopped, the transmission re-
To select reverse, press the clutch pedal to the floor. mains in low gear until drive is selected. If LOW is
Then press the R button. selected while the vehicle is moving, the transmis-
sion downshifts at a higher engine speed than nor-
N (Neutral) mal, in order to maximize the engine braking effect.
Neutral (N) is used for starting, parking, or any sta- To select LOW, press the clutch pedal to the floor.
tionary operation. No gear is selected. The transmis- Then press the LOW button. Slowly release the
sion must be in neutral to start the engine. clutch pedal and drive the vehicle.
IMPORTANT: If the vehicle starts up in any gear IMPORTANT: Before parking the vehicle, always
but neutral, bring the vehicle to an authorized do the following:
Freightliner service facility as soon as possible.
• Place the transmission in neutral.
To select neutral, press the clutch pedal to the floor.
• Set the parking brakes.
Then press the N button. Set the parking brakes and
slowly release the clutch pedal. • Chock the tires, if parking on an incline.
8.14
Truck-Manuals.net
Drivetrain
Freightliner SmartShift Shift 5 6 7

Control 4 8
3
General Information, SmartShift
The SmartShift transmission control is an electronic
transmission control device. It is installed with the
9
following transmissions: 1
2
• Eaton Fuller UltraShift™ 10
11
• Eaton Fuller UltraShift PLUS 12
01/24/2003 f270120
• Mercedes-Benz Automated Gear Shift (AGS)
To upshift manually, pull the lever up (towards you). To
It replaces the typical floor-mounted shift lever or downshift manually, push the lever down (away from
dash-mounted push button control. you).
1. SmartShift Control Lever
SmartShift accepts driver requests for transmission 2. Slide Switch (forward driving mode switch)
functions and transmits them through hard wiring to 3. MAN Mode (of slide switch)
the transmission control unit (TCU). SmartShift is a 4. AUTO Mode (of slide switch)
true shift-by-wire system. 5. Upshift Direction
6. Reverse Position (of selector switch)
SmartShift offers two main advantages over conven-
7. Selector Switch
tional transmission control devices. Without a floor- 8. Neutral Lock Button
mounted shift control, usable cab space is increased. 9. Neutral Position (of selector switch)
The SmartShift control mounts to the right-hand side 10. Drive Position (of selector switch)
of the steering column and is operated by the fingers 11. Low Position (of selector switch)
of the driver’s right hand, allowing both hands to re- 12. Downshift Direction
main on the steering wheel.
Fig. 8.10, SmartShift Control (with Eaton Fuller
A two-position slide switch (Fig. 8.10) is mounted on UltraShift and UltraShift PLUS)
the body of the control lever just before the paddle
widens out. The slide switch allows the driver to reverse ®). When shifting to N, it is not necessary to
choose automatic (AUTO) or manual (MAN) mode. press the neutral lock button.
In AUTO mode, gears shift automatically, without
driver interaction. Manual gearshifts are accom- Eaton Fuller UltraShift
plished by a momentary pull or push on the control in
the plane perpendicular to the steering wheel. Pull
Automated Transmissions
upward (toward you) on the control to upshift and The Eaton® Fuller® UltraShift™ transmission uses
push downward (away from you) to downshift. The the four-position SmartShift control lever on the
control is spring-loaded and returns to mid-position steering column to change gears, combined with a
when released after an upshift or downshift. gear indicator on the right-hand control panel as
For Eaton Fuller UltraShift and UltraShift PLUS shown in Fig. 8.12. All forward shifts can be made
(Fig. 8.10), a four-position ®, N, D, L) selector switch either manually or automatically, at the driver’s
is located at the end of the lever. For the Mercedes- choice. No clutch pedal is required to operate the
Benz AGS (Fig. 8.11), a three-position ®, N, D) se- vehicle.
lector switch is located at the end of the lever.
General Information, UltraShift ASW
Embedded in the selector switch is a small neutral
lock button to prevent accidental shifts into gear from UltraShift ASW is a six-speed medium-duty fully au-
neutral. Any time you shift through N, press down on tomated transmission used on the M106 only. Six-
the neutral lock button to move the switch from neu- speed UltraShift ASW uses a "wet" clutch system in
tral (N) to another gear, such as drive (D), low (L), or which the drive and driven discs rotate in a bath of
transmission fluid (Dexron III).
8.15
Truck-Manuals.net
Drivetrain
5 6
General Information, UltraShift DM
7
4 UltraShift DM is a ten-speed heavy-duty fully-
3 8 automated transmission used on the M112 only. Ten-
speed UltraShift DM uses a dry clutch system which
is offered only on this automated transmission sys-
tem.
9
1
2
10
Operation, UltraShift
Power Up
11
11/11/2002 f270080 NOTE: These operating instructions apply
To upshift manually, pull the lever up (towards you). To equally to six-speed UltraShift ASW and ten-
downshift manually, push the lever down (away from speed UltraShift DM, with the exceptions ex-
you). plained below.
1. SmartShift Control Lever
2. Slide Switch 1. With the parking brake set, select neutral (N) by
3. MAN Mode (of slide switch) moving the selector switch to the N position.
4. AUTO Mode (of slide switch)
2. With the transmission in neutral, turn on the igni-
5. Upshift Direction
6. Reverse Position (of selector switch) tion switch. The "CHECK TRANS" and "TRANS
7. Selector Switch TEMP" telltale lights come on and go out again
8. Neutral Lock Button (bulb check). See Fig. 8.13.
9. Neutral Position (of selector switch)
10. Drive Position (of selector switch) 1 2
11. Downshift Direction
Fig. 8.11, SmartShift Control (with Mercedes-Benz AGS) CHECK
TRANS
TRANS
1 TEMP
BRAKE
2
10/27/2003 f610677
1. "CHECK TRANS" Light
2. "TRANS TEMP" Light
Fig. 8.13, Telltale Lights, UltraShift Transmission
3. After the ignition is turned on, the current gear

indicator shows the dot display, arranged in a
square pattern. All dots in the pattern should light
10/13/2003 f270079 up, without gaps or spaces. See Fig. 8.14.
To know what gear the transmission is in, look at the 4. Wait for the current gear indicator to show a solid
current gear indicator. "N." When the "N" is solid, rather than flashing,
1. Gear Indicator the UltraShift transmission control unit (TCU) is
2. SmartShift Control powered up. Apply the service brake and start
Fig. 8.12, Shift Controls and Indicators, UltraShift the engine.
Transmissions
8.16
Truck-Manuals.net
Drivetrain
7.2 To stop on a hill or grade, press and hold

the brake pedal to keep the vehicle from
moving.
On steep hills, set the parking brake.
When parking, chock the tires, front and/or
rear. Never hold a hill with the throttle
pedal. This will cause the clutch to over-
heat.
Power Down
1. Apply the service brake.
2. Select neutral (N) by moving the selector switch
10/13/2003 f610678 to the N position. When the "N" on the gear indi-
cator is solid, rather than flashing, the UltraShift
Fig. 8.14, Power-Up Dot Display TCU is ready to power down. See Fig. 8.13.
5. Select drive (D) by pressing in the neutral lock 3. With the transmission in neutral, set the parking
button and moving the selector switch downward brake.
to the position below neutral. Release the park- 4. Turn off the ignition key and shut down the en-
ing brake. The gear is displayed on the current gine.
gear indicator.
NOTE: When D is selected, the transmission Automatic and Manual Modes
controller starts up in second gear. On both six- The SmartShift control has a slide switch located on
speed Ultrashift ASW and ten-speed Ultrashift the body of the control lever just before the paddle
DM, the driver can select to start up in first. No widens out. See Fig. 8.15. The slide switch controls
other start gear is available. the forward driving mode, automatic or manual.
6. On a level grade, release the service brake and
press down on the throttle pedal to allow the ve-
hicle to move forward.
WARNING
When starting or stopping on hills and grades,
use extra care to prevent the vehicle from rolling
back. A rollback accident could cause death, seri- 1 2
ous personal injury, or property damage.
3
7. Prevent the vehicle from rolling backward when
stopped on a hill or grade, or when the vehicle is
starting from a stop on a hill or grade.
7.1 To start from a full stop on a hill or grade,
quickly move your foot from the brake
pedal and press firmly on the throttle 01/21/2004 f270079c
pedal. 1. Slide Switch (controls forward driving mode)
2. Selector Switch (controls gear selection)
On steep hills, set the parking brake and 3. Neutral Lock Button (prevents accidental shift into
release it only when there is enough en- gear)
gine power to prevent rollback.
Fig. 8.15, Switches, Ultrashift Transmission
8.17
Truck-Manuals.net
Drivetrain
To change mode at any time, move the slide switch shift if the engine speed is within 75 rpm of the load-
in the desired direction. This allows the driver to re- based shift point for that gear.
spond to a wide range of driving conditions, such as
If the driver presses down on the throttle pedal after
blind corners, tight curves, and steep hills.
a manual downshift in automatic mode, the transmis-
IMPORTANT: Whatever the mode, it is always sion will upshift again if the UltraShift TCU requires
possible to shift manually by moving the lever it.
up or down as needed. When the engine speed
is within 75 revolutions per minute (rpm) of the Manual Mode (MAN)
load-based shift point for an automatic shift, the In manual drive mode (MAN), upshifts and down-
UltraShift TCU will advance the shift. shifts are made by the driver:
In either mode, the gear indicator displays the cur- • To shift up, pull the lever up (towards you).
rent gear. See Fig. 8.16. • To shift down, push the lever down (away from
you).
The system will hold the current gear until the driver
requests a shift. In downhill situations in particular,
the driver must be alert to vehicle speed by down-
shifting and/or using the service brake.
A shift request will still be refused if the selected gear
would cause engine overspeed or excessive lugging.
Selecting Gears
Reverse
Reverse (R) is at the upper end of the four-position
selector switch located at the end of the SmartShift
10/13/2003 f610680 control lever. To select R, press in the neutral lock
NOTE: The gear indicator displays the current gear. In
button and move the selector switch upward to the
this example, it displays first gear. position above neutral.
Fig. 8.16, Current Gear Display Six-speed UltraShift ASW has one reverse gear.
When reverse is selected, the letter "R" displays on
At the start of a shift, the current gear continues to the gear indicator. See Fig. 8.17.
display until the transmission has been pulled into
neutral. At this point, as the transmission is synchro-
nizing for the new (target) gear, the gear indicator
flashes the number of the new gear.
When the shift is complete, the new gear displays
solid, without flashing.
Automatic Mode (AUTO)

In automatic drive mode (AUTO), upshifts and down-
shifts are made by the transmission without driver
intervention. Press in the neutral lock button, move
the selector switch to drive (D), and press down on
the throttle pedal. The transmission will shift auto-
matically.
10/14/2003 f610681
If driving conditions require, it is still possible to re-
quest a manual shift. The transmission will make the Fig. 8.17, Reverse Gear Display
8.18
Truck-Manuals.net
Drivetrain
Ten-speed UltraShift DM has two reverse gears, re-

verse low and reverse high. To shift manually be- WARNING
tween them, use the shift lever as described for MAN
mode. There is no AUTO mode for reverse. Do not coast in neutral. Coasting in neutral can
cause an accident, possibly resulting in severe
When reverse low is selected, the letter "R" displays personal injury or death.
on the current gear indicator. When reverse high is
selected, the letter "H" displays on the current gear Neutral is always available during operation, what-
indicator. ever the vehicle speed. When in neutral, requests to
upshift or downshift are ignored. If the selector switch
IMPORTANT: Under normal conditions, do not is moved from neutral to drive while the vehicle is
select reverse with the vehicle moving forward. moving, the transmission will shift into a gear within
the engine’s operating speed range.
The vehicle must be moving at less than two miles
per hour (3 km/h) before selecting reverse. If reverse When shifting from neutral, always press on the
is selected when the vehicle is moving faster, an au- brake pedal. If the brake pedal is not pressed, the
dible alert will sound and continue sounding at three- transmission will not shift, the current gear display
second intervals until the control lever is returned to will flash "N," and an audible alert will sound.
the D position. When the vehicle is moving at the
proper speed, reverse can be engaged. NOTE: To reset the transmission, return the se-
lector switch on the SmartShift lever to N and
On ten-speed UltraShift DM only, if necessary to rock attempt the shift again, this time with the brake
the vehicle, use the selector switch to shift back and pedal pressed.
forth at low speed between reverse and drive.
Before shutting down the engine, return the selector
Neutral switch to "N." When the ignition is turned off, the
transmission will reset to neutral in a few minutes
IMPORTANT: Always start the engine with the regardless of the position of the shift lever.
transmission in neutral, the parking brake set,
and the service brakes applied. Drive
Neutral (N) is directly below R on the four-position Drive (D) is directly below N on the four-position se-
selector switch located at the end of the SmartShift lector switch located at the end of the SmartShift
control lever. To select N, move the selector switch to control lever. To select D, press in the neutral lock
the position below R. When neutral is selected, the button and move the selector switch to the position
letter "N" displays on the gear indicator. See below N. When drive is selected, the number of the
Fig. 8.18. currently selected forward gear (1 through 6 on six-
speed UltraShift ASW; 1 through 10 on ten-speed
UltraShift DM) displays on the gear indicator. See
Fig. 8.16.
When in drive, requests to upshift or downshift are
enabled. Either manual or automatic mode can be
selected on the slide switch.
Two starting gears are available, first and second.
The default starting gear is second, but first can be
selected by the driver, if desired. To change the start-
ing gear, press the brake pedal and select D with the
vehicle stopped. The current gear indicator will dis-
play the starting gear. Move the shift lever up or
down until the desired starting gear is displayed.
10/13/2003 f610679 The UltraShift TCU adapts to the working conditions
of each vehicle and its driver. After power-up or a
Fig. 8.18, Neutral Display load change, it needs to learn the new conditions.
8.19
Truck-Manuals.net
Drivetrain
While learning, it may hold a gear too long before If the gear is available, the transmission downshifts
upshifting. Start the upshift manually. It may take and the new gear displays on the gear indicator. Skip
three or four shifts before UltraShift succeeds in shifts are available while downshifting.
learning the new load-based shift points, but after
For best engine braking, select low while moving. In
that it will handle the shifting automatically.
low, downshifts are performed at higher rpm than in
Low drive.
Low (L) is located at the lower end of the four- IMPORTANT: If the engine is approaching over-
position selector switch located at the end of the speed, the UltraShift TCU will override the cur-
SmartShift control lever. To select L, press in the rent gear setting and upshift to prevent engine
neutral lock button and move the selector switch to damage.
the position below D.
If the gear requested is unavailable, a tone will
When in low, the current gear is maintained. Re- sound. An unavailable request to downshift is not
quests to upshift are not enabled. stored in memory. The downshift must be requested
again.
IMPORTANT: If the engine is approaching over-
speed, the UltraShift TCU will override the cur- When coasting to a stop, the UltraShift TCU may not
rent gear setting and upshift to prevent engine finish the downshift until the driver presses down on
damage. the throttle pedal again.
To enhance engine braking, downshifts are per- IMPORTANT: A downshift request can never
formed at higher rpm than normal. result in a shift into neutral, even if the vehicle is
in the drive position in the lowest possible gear.
If L is selected from neutral while stopped, the ve-
hicle starts up in first gear and stays there until the Before starting down a hill, slow down. Downshift to
engine approaches overspeed. a speed that you can control without hard pressure
on the service brakes.
Upshifting
Before entering a curve, slow down to a safe speed.
To request an upshift with the transmission in drive, Downshift if necessary. This lets you use some
pull the control lever up (towards you). If the gear is power through the curve to help the vehicle be more
available, the transmission upshifts and the new gear stable on the turn. It also allows you to regain speed
displays on the gear indicator. No skip shifts are faster as you come out of the curve.
available while upshifting.
No upshifts are available in low, except to prevent
UltraShift Diagnostics
engine overspeed. Clutch Calibration
If the transmission does not upshift quickly enough NOTE: Clutch calibration only occurs on six-
after power-up or a load change, begin the shift speed UltraShift ASW.
manually. The UltraShift TCU will learn the new load-
based shift conditions after three or four shifts. The UltraShift TCU automatically adjusts for clutch
wear. The calibration takes place whenever the fol-
If the gear requested is unavailable, a tone will lowing conditions are met:
sound. An unavailable request to upshift is not stored
in memory. The upshift must be requested again. • The engine is at normal operating temperature
• The vehicle is stopped
Downshifting
• The engine is at idle speed
NOTE: The driver can manually downshift at
any time, even when the slide switch is set to • The selector switch on the control lever is in
AUTO mode. neutral
To request a downshift with the transmission in drive
or low, push the control lever down (away from you).
8.20
Truck-Manuals.net
Drivetrain
Calibration may take up to two minutes to complete. 4. Wait at least two minutes with the engine shut
The engine may slow and return to normal idle sev- down.
eral times during calibration.
5. Restart the engine.
To stop calibration at any time, select one of the
drive positions on the selector switch (R, D, or L). If the problem continues, contact an authorized
Freightliner or Eaton service facility.
Clutch Protection Fault
Locked In Gear
Excessive clutch slippage creates heat and reduces If the transmission becomes locked in gear, a dash
the life of the clutch. These are some conditions (–) will appear on the gear indicator when the vehicle
which lead to clutch abuse: is restarted during the reset procedure.
• Using the throttle to hold the vehicle on a
NOTE: If the transmission becomes locked in
grade
gear while the vehicle is moving, increased
• Starting the vehicle in too high a gear braking effort may be required to stop the ve-
• Overloading the vehicle hicle.
• Using high idle with the vehicle in gear If the current gear indicator displays a dash during
power-up with the selector switch in neutral, do the
The UltraShift TCU is programmed to prevent clutch following steps:
abuse. When the clutch overheats, the following
alerts take place: 1. Make sure the parking brake is set.
• The "TRANS TEMP" light comes on 2. Turn off the ignition and wait at least two min-
utes.
• The gear indicator displays "CA"
3. Apply the service brakes.
• A warning tone sounds at one second intervals
4. With the service brakes applied, release the
The alerts continue until the clutch cools, the throttle parking brake.
is released, or the clutch is fully engaged.
5. Make sure the selector switch is in neutral and
System Problem turn on the ignition key. Do not attempt to start
the engine at this time.
In the event of a problem, do the following steps:
6. If necessary to get the transmission to shift into
1. Note the driving conditions at the time the prob- neutral, release the pressure on the brake pedal
lem occurred. slightly.
2. Record the status of the transmission at the time 7. Once the UltraShift TCU reaches neutral, a solid
of the problem (AUTO or MAN mode, gear set- "N" will appear on the current gear indicator and
ting R, N, D, or L, current gear, engine speed, the vehicle will start. Make sure the service
etc.) brakes are applied and the parking brake is set.
3. Reset the system, using the procedure below. If the gear indicator continues to display a dash, con-
tact an authorized Freightliner or Eaton service facil-
Reset Procedure ity.
Transmission operation can sometimes be restored
by doing the following reset procedure: Eaton Fuller UltraShift PLUS
1. Stop the vehicle when it is safe to do so. Automated Transmissions
2. Place the selector switch in neutral and turn off Eaton Fuller UltraShift PLUS automated transmis-
the ignition. sions use shift selection software and electric clutch
3. Check all harness connectors as described in actuation; a clutch pedal is not needed to operate the
Chapter 11. vehicle. These transmissions use the four-position
8.21
Truck-Manuals.net
Drivetrain
SmartShift control (see Fig. 8.10) on the steering vehicle will not engage reverse above 2 mph (3
column to select mode, direction, neutral, low, and to km/h).
make manual shifts. To know what gear the transmis-
sion is in, see the current gear indicator on the dash. Reverse (R) is at the upper end of the four-position
Forward shifts can be made either manually or selector switch located at the end of the SmartShift
automatically. control. To select R, press in the neutral lock button
and move the selector switch to the position above
Power Up neutral. The default Reverse gear is engaged.
NOTE: Engine cranking is delayed until the NOTICE

transmission power-up is complete and the gear
display shows a solid "N". Avoid launching the vehicle in high range.
Launching the vehicle in high range increases
1. With the parking brake set, turn the ignition the likelihood of clutch abuse and could be detri-
switch to the ON position. mental to clutch life.
2. Start the engine.
3.
Automatic Mode (AUTO)
Apply the service brake.
In automatic drive mode (AUTO), upshifts and down-
NOTE: If the service brake is not applied while shifts are made by the UltraShift PLUS without driver
selecting a starting gear, the initial start gear will intervention. Press in the neutral lock button, move
not be found and the driver will need to select the selector switch to Drive (D), and press down on
Neutral and press the service brake while se- the throttle pedal. The transmission will shift auto-
lecting the desired mode. matically.
4. Select the desired mode and starting gear. (Inap- NOTE: If attempting to select a non-Neutral
propriate start gear selections are ignored to mode without applying the service brakes, the
avoid damaging the transmission.) transmission will not shift into gear. To shift into
5. Release the parking brake. gear, select Neutral, apply the service brakes,
and select the desired mode again.
6. Release the service brake and apply the accel-
erator. In Drive, the start gear is automatically selected. The
selected start gear can vary depending on several
Power Down vehicle inputs such as load, grade, and axle/
transmission ratio. The start gear can be changed
1. Select Neutral on the shift control. using the SmartShift control, provided the selected
gear would allow the vehicle to launch without dam-
NOTE: If the gear display does not show a solid
aging the transmission. If the start gear is changed
"N", neutral has not yet been obtained. Neutral using the SmartShift control, it will be the default until
should always be reached before powering the vehicle is powered down or the selection is
down an UltraShift PLUS, except in cases of changed again manually.
emergency.
IMPORTANT: Prior to ascending a steep grade,
2. Set the parking brake. either reduce the default start gear by one
3. Turn off the ignition, and shut down the engine. (using the SmartShift control) or apply full
throttle for the duration of the grade so the ve-
Reverse (R) hicle maintains the proper engine and vehicle
speed during the entire grade.
NOTE: If attempting to select a non-Neutral
mode without applying the service brakes, the In Drive, the transmission automatically performs up-
transmission will not shift into gear. To shift into shifts and downshifts. However, when the transmis-
sion is near the shift point, the shift can be forced
gear, select Neutral, apply the service brakes,
using the upshift or downshift function of the Smart-
and select the desired mode again. Also, the Shift control.
8.22
Truck-Manuals.net
Drivetrain
NOTE: The transmission may deny a shift while coming to a stop. To select Low, press in the neutral
ascending or descending a grade if the load of lock button and move the selector switch to the L
the vehicle and grade of the terrain in combina- position. The lowest available start gear will be se-
tion with the drivetrain ratio and engine torque lected (the starting gear cannot be changed in Low).
fall outside of the acceptable range to perform a If Low is selected while moving, the transmission will
shift. If the shift is denied, a tone will sound. not upshift (unless the system initiates a Low over-
ride). The system will downshift at the earliest oppor-
Manual Mode (MAN) tunity to provide maximum engine braking.
In manual mode (MAN), the driver selects upshifts NOTE: If attempting to select a non-Neutral
and downshifts instead of letting the UltraShift PLUS mode without applying the service brakes, the
select them automatically. Manual shifting may be transmission will not shift into gear. To shift into
helpful when traversing a work site, railroad tracks, gear, select Neutral, apply the service brakes,
or steep grades, for example. To drive forward, press and select the desired mode again.
in the neutral lock button, move the selector switch to
Drive (D), and press down on the throttle pedal. To Low Override
shift up, pull the lever up (towards you); to shift
down, push the lever down (away from you). The The system is equipped with a Low override function.
system holds the current gear unless a shift is re- If the vehicle is being "back driven" (for example, de-
quested or if the system initiates a manual mode scending a grade and vehicle speed exceeds engine
override. speed) and the engine speed is excessively high, the
system will upshift automatically. Also, if the start
NOTE: The transmission may deny a shift while gear is changed and it causes the engine to lug at
ascending or descending a grade if the load of takeoff, the system will override the current position
the vehicle and grade of the terrain in combina- and upshift.
tion with the drivetrain ratio and engine torque
fall outside of the acceptable range to perform a Clutch Abuse Protection
shift. If the shift is denied, a tone will sound. Although a vehicle equipped with an UltraShift PLUS
NOTE: If attempting to select a non-Neutral uses an automated clutch, the clutch can still over-
mode without applying the service brakes, the heat and slip with improper use. The clutch abuse
transmission will not shift into gear. To shift into protection feature helps protect the clutch if the auto-
mated clutch starts to overheat. When the clutch
gear, select Neutral, apply the service brakes,
abuse protection feature initiates and sounds a warn-
and select the desired mode again. ing tone, full clutch actuation must be completed
quickly. If it is not completed quickly enough, the sys-
Manual Mode Override tem will either open the clutch (if the throttle pedal is
The system is equipped with a manual mode over- not being pressed) or close the clutch (if the throttle
ride function. If the vehicle is being "back driven" (for pedal is being pressed). If the abuse continues, the
example, descending a grade and vehicle speed ex- system will open the clutch and take away throttle
ceeds engine speed) and the engine speed is exces- control briefly to allow the clutch to cool down.
sively high, the system will upshift automatically. To protect the clutch:
Also, if the start gear is changed and it causes the
engine to lug at takeoff, the system will override the • Select the lowest possible start gear for the
current position and select the best available gear. application.
• Use Creep Mode when appropriate.
Low (L)
• Use the service brakes and the Hill Start Aid
Low (L) is at the lower end of the four-position selec- when launching on a grade.
tor switch located at the end of the SmartShift con-
trol. Use Low when wanting to maximize engine • Minimize the time it takes to engage the clutch
braking and minimize the use of the brake pedal—for from rest.
example, when driving down long grades or when
8.23
Truck-Manuals.net
Drivetrain
• Do not use the throttle to hold the vehicle on a Hill Start Aid
grade; use the service brakes.
UltraShift PLUS transmissions are equipped with a
• Do not use the throttle to stop roll back on an Hill Start Aid (HSA) feature to prevent the vehicle
incline after Hill Start Aid disengages; use the from rolling while on grades steeper than 3% and
service brakes, and then relaunch. allow for a controlled launch. A grade sensor is used
• Do not continually start and stop, especially to determine when to engage the feature.
when loaded; use a lower gear or Creep Mode. HSA is "on" by default. It can be turned off by press-
ing and releasing the override switch on the dash.
Creep Mode HSA will turn back on after the first successful
The Creep Mode function allows the vehicle to main- launch.
tain a constant speed at engine idle without the When the vehicle is stopped on a grade greater than
driver holding the throttle pedal position. This mode 3% and in a forward mode or reverse, depress the
is useful for very low-speed maneuvering and appli- service brakes then release them. The vehicle will
cations where steady vehicle speed is required. The begin to move after 3 seconds, and the clutch will
vehicle speed is determined by the selected gear perform partial engagements to slow the vehicle mo-
ratio operating at governed low engine idle speed. tion. Either step on the brake or apply the throttle to
Any available gear may be selected, though the continue negotiating the grade.
transmission will downshift or exit Creep Mode to
prevent stalling if the engine lugs due to load condi- Engine Overspeed Protection
tions.
The system will upshift if necessary to prevent en-
By default, Creep Mode can be activated while in gine overspeed in Drive, Manual, and Low.
Manual Mode or Low. Eaton’s ServiceRanger diag-
nostic software can be used to enable Creep Mode Shuttle Shifting
in Automatic Mode and/or Reverse.
Shuttle shifting from reverse to any forward mode is
Engaging Creep Mode only allowed if the vehicle speed is approximately
zero.
To engage Creep Mode:
1. Select Low or Manual Mode and the desired Auto Start Gear Selection and
gear (while stopped or moving). Override
2. Apply the throttle pedal to accelerate the vehicle The UltraShift PLUS system uses various inputs to
until the clutch is closed (engaged). automatically select the best start gear in Drive and
3. Release the throttle pedal. The vehicle will con- Manual. This selection can be changed using the
tinue moving at governed low engine idle speed. SmartShift control; however, if the selection re-
quested could cause damage or engine lugging, the
Exiting Creep Mode request will be denied and a tone will sound.
To exit Creep Mode, apply the throttle pedal to accel- Skip Shifting
erate temporarily, or select a higher gear in Manual
Mode. (Creep Mode can be resumed in the selected When appropriate, the UltraShift PLUS system may
gear by releasing the throttle pedal.) skip shift in Drive. When prevailing conditions like
load and grade allow, skip shifts can be performed in
NOTE: The transmission will exit Creep Mode if Manual mode using the SmartShift control.
the engine lugs 150 rpm below the governed
low engine idle speed. In this case, a lower gear Auto Neutral
should be selected if available.
The UltraShift PLUS system will automatically shift to
neutral if the vehicle is left in Drive and the parking
brake is set. "AN" will show on the gear display. To
8.24
Truck-Manuals.net
Drivetrain
re-engage the transmission, select Neutral and then loads or powering up, the system needs to relearn
either Drive or Reverse on the shift control (it will re- these inputs for the first few shifts to make the
engage regardless of whether the parking brake is proper adjustments.
released).
Coasting
Automatic Traction Control
When coasting to a stop on level terrain, the Ultra-
The UltraShift PLUS system requires the Automatic Shift PLUS system may not downshift into the lower
Traction Control (ATC) option to be enabled when gears. It will select a gear after the throttle is applied.
driving in soft soil/sand to prevent wheel slippage
and shifting issues. The ATC system has two modes:
"normal" (for sand and loose road surface) and a
Mercedes-Benz Manual
mud/snow setting. Transmissions
ATC Normal Mode CAUTION
In normal mode, the system will engage the brakes
on the wheel or side that the wheel slip is occurring Operating a manual transmission with the fluid
to help the vehicle gain traction. The point at which level higher or lower than recommended can re-
the traction control will actuate the braking system sult in transmission damage.
increases with throttle: low throttle allows the system Mercedes-Benz transmissions use a simple 6-speed
to brake the wheels earlier; heavy/full throttle raises gear pattern as shown in Fig. 8.19.
the point of the acceptable wheel slip.
Adhere to the following points when driving in ATC
normal mode: 1 3 5
• If using Automatic mode in soft soil and/or
sand, maintain the engine speed between N
1000 and 1300 rpm to prevent unnecessary
upshifting. R 2 4 6
• If using Manual mode in soft soil and/or sand, 05/03/2001 f261098
do not attempt an upshift and try to maintain
the current gear. Fig. 8.19, Shift Pattern, M-B Transmissions
• If the vehicle comes to a stop in the sand it Always use first gear when starting to move the ve-
may be necessary to back up prior to attempt- hicle forward.
ing forward movement.
IMPORTANT: Do not rest your foot on the clutch
ATC Mud/Snow Mode pedal while driving. This causes partial clutch
disengagement which could cause premature
To select the mud/snow mode, depress the ATC
switch. This mode raises the wheel slip speed that is clutch wear.
allowed before the traction control activates. The While traveling, check the tachometer regularly to be
point at which the traction control will actuate the sure the engine speed is within the most economical
braking system increases with throttle: low throttle range (1400 to 2000 rpm).
allows the system to brake the wheels earlier; heavy/
full throttle raises the point of the acceptable wheel On level roads, drive in the highest usable gear,
slip. keeping engine speed down.
Load-Based Shifting
The UltraShift PLUS system is adaptive and will
change the shift points based on grade, engine RPM,
throttle position, and vehicle load. After changing
8.25
Truck-Manuals.net
Drivetrain
the driver’s pressure on the brake and throttle ped-

CAUTION als. To know which gear the transmission is in, look
at the round current gear indicator on the right-hand
Do not rest your hand on the gear shift lever control panel as shown in Fig. 8.12.
while driving. This can cause synchronizer dam-
age. The TCU always selects first gear to start the vehicle
in motion. It is possible, in manual mode, to start an
When approaching an uphill grade, shift down ahead unloaded or lightly loaded vehicle in second gear. In
of time to prevent loss of engine rpm. When ap- most cases, second gear is acceptable for downhill
proaching a downhill grade, shift down ahead of time starts. In other situations, for best results always start
to prevent runaway speed. For information about moving in first gear. Loaded vehicles, or vehicles on
shift points and "progressive shifting," see Chap- substantial grades, must start moving only in first
ter 7. gear.
Change gears only when absolutely necessary. Skip
gears if needed. CAUTION
When shifting, always press the clutch pedal all the At the first sign of a transmission malfunction,
way down. Do not force the gear lever. take the vehicle out of service immediately. De-
Before shifting into reverse, be sure the engine is pending on the type of problem, further shifting
idling and the vehicle is not moving. may not be possible, and driveline torque may be
interrupted.
CAUTION Operation, AGS
If the transmission locks up while driving, mak- Power Up
ing further shifting impossible, continue driving
in the gear already selected to reach service as- 1. With the parking brake set and/or the brake
sistance, as circumstances allow. Or, safely park pedal pressed down, select neutral (N) by mov-
the vehicle off the roadway and contact your ing the selector switch to the center position.
nearest Freightliner dealer or other qualified ser- 2. With the transmission in neutral, turn on the igni-
vice provider for roadside assistance. To prevent tion switch. The "CHECK TRANS" and "TRANS
further transmission damage, do not move the TEMP" telltale lights come on and go out again
vehicle from a standing start unless this can be (bulb check). See Fig. 8.13.
accomplished safely, taking into account the gear
that is engaged and the load on the vehicle. 3. On power up, the current gear indicator shows
the dot display, arranged in a square pattern. All
dots in the pattern should light up, without gaps
Mercedes-Benz Automated or spaces. See Fig. 8.14.
Transmissions 4. When the current gear indicator shows "N," start
General Information, AGS the engine.
The AGS Automated Gear Shift is a fully automated NOTE: No matter what the circumstances, do
6-speed medium-duty transmission. The clutch is ac- not start the engine unless the current gear indi-
tivated by a hydraulic system that is integral to the cator shows "N." See Chapter 13 for jump start-
transmission. No clutch pedal is needed to operate ing information.
the vehicle.
5. Select drive (D) by pressing in the neutral lock
AGS transmissions use the SmartShift control lever button and moving the selector switch downward
on the steering column to select gears. A manual to the position below neutral. Release the park-
shift is possible at any time by moving the SmartShift ing brake and/or service brake pedal. The gear is
lever up or down as needed. displayed on the current gear indicator.
The transmission control unit (TCU) can direct all
forward shifts in response to driving conditions and
8.26
Truck-Manuals.net
Drivetrain
NOTE: When D is selected, the transmission in death, serious personal injury, or property
starts up in first gear. To start up in second gear damage.
(downhill start, vehicle unloaded or lightly 4. Turn the ignition switch off and shut down the
loaded), pull up on the SmartShift lever when engine.
the current gear indicator displays "1."
5. If the current gear indicator flashes "PB" when
6. On a level grade, press down on the throttle the engine is shut down, set the parking brake
pedal to allow the vehicle to move forward. The and move the selector switch to "N."
vehicle will not move until the pedal is de-
pressed. Automatic and Manual Modes
The SmartShift control has a slide switch located on
WARNING the body of the lever just before the paddle widens
out. See Fig. 8.20. The slide switch controls the for-
When starting or stopping on hills and grades, ward driving mode, automatic or manual.
use extra care to prevent the vehicle from rolling
back. A rollback accident could cause death, seri-
ous personal injury, or property damage.
7. Prevent the vehicle from rolling backwards when
stopped on a hill or grade, or when the vehicle is
starting from a stop on a hill or grade.
7.1 To start from a full stop on a hill or grade,
quickly move your foot from the brake
pedal and press firmly on the throttle 1 2
pedal.
3
On steep hills, set the parking brake and
release it only when there is enough en-
gine power to prevent rollback.
7.2 To stop on a hill or grade, press and hold
the brake pedal to keep the vehicle from
moving. 01/19/2004 f270079b
On steep hills, set the parking brake. 1. Slide Switch (controls forward driving mode)
Never hold a hill with the throttle pedal. 2. Selector Switch (controls gear selection)
This will cause the clutch to overheat. 3. Neutral Lock Button (prevents accidental shift into
gear)
Power Down Fig. 8.20, Switches, AGS Transmissions
1. Bring the vehicle to a complete stop.
To change mode at any time, move the slide switch
2. Set the parking brake. in the desired direction. This allows the driver to re-
spond to a wide range of driving conditions, such as
3. Move the selector switch to N. Wait until "N" ap- blind corners, tight curves, and steep hills.
pears on the current gear indicator.
IMPORTANT: Whatever the mode, it is always
WARNING possible to shift manually by moving the lever
up or down as needed.
Always apply the parking brake before shutting
In either mode, the gear indicator displays the cur-
down the engine. AGS will shift into neutral after
rent gear. See Fig. 8.16.
shutdown, regardless of the position of the shift
lever. If you do not set the parking brake, the ve-
hicle could roll and cause an accident resulting
8.27
Truck-Manuals.net
Drivetrain
Automatic Mode (AUTO) • To shift up, pull the lever up (towards you).
Automatic drive mode (AUTO) is recommended for • To shift down, push the lever down (away from
most driving conditions. For the best fuel economy, you).
always use AUTO mode.
The system will hold the current gear until the driver
In AUTO mode, upshifts and downshifts are made by requests a shift. In downhill situations in particular,
the transmission without driver intervention. Press in the driver must be alert to vehicle speed and main-
the neutral lock button, move the selector switch to tain vehicle control by downshifting and/or using the
drive (D), and press down on the throttle pedal. The service brakes as needed.
transmission will shift automatically through the for-
ward gears. When braking or slowing in MAN, downshift as nec-
essary to prevent lugging the engine when speed is
If driving conditions require, it is still possible to re- resumed. If the vehicle comes to a complete stop,
quest a manual shift. The transmission will make the the TCU resets the transmission to neutral.
shift unless the selected gear would cause engine
overspeed. NOTE: A downshift request will be refused if the
selected gear would cause engine overspeed.
If the driver presses down on the throttle pedal after
a manual downshift in automatic mode, the transmis- Cruise Control
sion will upshift again if the TCU requires it.
Cruise control is fully functional with AGS transmis-
On downgrades, the transmission holds the current sion in either AUTO or MAN mode.
gear until the driver requests a shift, or presses the
throttle pedal. In AUTO, the TCU will adjust the gear selections to
maintain the speed settings as desired. No driver
action is necessary.
WARNING
In MAN, the vehicle speed settings must be within
While driving off-road or with locked differential the engine speed range for the gear selected. If the
in AUTO mode, use extra caution. Shifts of the engine cannot maintain set speed due to changes in
AGS could interrupt power to the drive wheels, road grade, the driver must downshift or upshift as
causing a rollback accident while climbing steep necessary.
grades at low speeds. A rollback accident could
For vehicles equipped with a power take-off (PTO)
cause death, serious personal injury, or property
unit, two modes of operation are possible, stationary
damage.
and mobile. For PTO operation, see Chapter 7.
Manual Mode (MAN) Selecting Gears
Manual mode may be required under certain condi-
tions, such as:
Reverse
Reverse (R) is at the upper end of the three-position
• In difficult or slippery conditions
selector switch located at the end of the SmartShift
• On hills, steep grades, or other situations control lever. To select reverse (R), press in the neu-
where driveline torque interruption is not desir- tral lock button and move the selector switch upward
able to the position above neutral. When reverse is se-
lected, the letter "R" displays on the gear indicator.
• During off-road driving or driving with a locked See Fig. 8.17.
differential
IMPORTANT: The vehicle must come to a com-
• In downhill driving where control of engine
plete stop before selecting reverse. If reverse is
braking is needed
selected with the vehicle moving forward, an
• If necessary to hold a specific gear on a down- audible alert will sound and continue sounding
grade at three-second intervals until the selector
In manual drive mode (MAN), upshifts and down- switch is returned to N or D.
shifts are made by the driver:
8.28
Truck-Manuals.net
Drivetrain
Once the vehicle has come to a complete stop, re- the currently selected forward gear (1, 2, 3, 4 , 5, or
verse can be engaged. 6) displays on the gear indicator.
Neutral Upshifting
Neutral (N) is in the center of the three-position se- NOTE: The driver can manually upshift at any
lector switch located at the end of the SmartShift time, even when the slide switch is set to AUTO
control lever. Always start the engine in neutral. To mode.
select neutral, move the selector switch to the center
position. When neutral is selected, the letter "N" dis- To request an upshift with the transmission in drive,
plays on the gear indicator. See Fig. 8.18. pull the control lever up (towards you). If the gear is
available, the transmission upshifts and the new gear
WARNING displays on the gear indicator.
As in a manual transmission, upshifting too early
Do not coast in neutral. Coasting in neutral can causes engine lugging and uneven operation.
cause an accident, possibly resulting in severe
personal injury or death. To achieve smooth operation in MAN mode, upshift
when the engine speed reaches approximately 2000
Neutral is always available during operation, what- revolutions per minute (rpm). Heavy loads or steep
ever the vehicle speed. When in neutral, requests to grades require higher rpm; lighter loads require lower
upshift or downshift are ignored. If the selector switch rpm.
is moved from neutral to drive while the vehicle is
moving, the transmission will shift into a gear within An unavailable request to upshift is not stored in
the operating torque range of the engine. memory. The upshift must be requested again.
Downshifting
WARNING
NOTE: The driver can manually downshift at
Always apply the parking brake before shutting any time, even when the slide switch is set to
down the engine. AGS will shift into neutral after AUTO mode.
shutdown, regardless of the position of the shift
lever. If you do not set the parking brake, the ve- To request a downshift with the transmission in drive,
hicle could roll and cause an accident resulting push the control lever down (away from you). If the
in death, serious personal injury, or property gear is available, the transmission downshifts and
damage. the new gear displays on the gear indicator.
Before shutting down the engine, return the selector Downshifts are not available if the engine speed after
switch to "N." When the ignition is turned off, the the shift would exceed 2700 rpm. If the gear re-
transmission will reset to neutral during power down. quested is unavailable, an audible alert will sound.
An unavailable request to downshift is not stored in
Drive memory. The downshift must be requested again.
IMPORTANT: The vehicle must come to a com- To achieve smooth operation in MAN mode, down-
plete stop before selecting drive. If drive is se- shift when the engine speed reaches approximately
lected with the vehicle moving in reverse, an 1200 rpm.
audible alert will sound and continue sounding Before starting down a hill, slow down. Downshift to
at three-second intervals until the selector a speed that you can control without hard pressure
switch is returned to N or R. on the service brakes.
Drive (D) is at the lower end of the three-position se- Before entering a curve, slow down to a safe speed.
lector switch located at the end of the SmartShift Downshift if necessary. This lets you use some
control lever. To select drive, press in the neutral lock power through the curve to help the vehicle be more
button and move the selector switch to the position stable when turning. It also allows you to regain
below neutral. When drive is selected, the number of speed faster as you come out of the curve.
8.29
Truck-Manuals.net
Drivetrain
AGS Diagnostics NOTE: After hydraulic fluid loss, a special pro-

cedure is required to fill the hydraulic reservoir.
This procedure must be carried out by an autho-
CAUTION rized Freightliner service facility.
At the first sign of a transmission malfunction,
take the vehicle out of service immediately. De- Meritor™ Drive Axles
pending on the type of problem, further shifting
may not be possible, and driveline torque may be Refer to the Meritor website for additional informa-
interrupted. tion, www.arvinmeritor.com.
System Malfunction Drive Axles With Differential Lock
If the "CHECK TRANS" telltale light comes on while The Meritor driver-controlled differential lock feature
driving, the audible alert sounds, and the current (side-to-side wheel lock, traction control, or traction
gear indicator begins to flash between the current equalizer) is available on single-drive or dual-drive
gear and "SM" (system malfunction), there is a prob- rear axles. It is available on both axles of a dual-
lem which may or may not be apparent to the driver. drive vehicle, or on one only. It is only available on
Bring the vehicle at once to a safe stopping place drive axles. Differential lock must only be used under
and call an authorized Freightliner service facility for adverse road conditions where greater traction is
assistance. needed. With differential lock on, the turning radius is
increased and vehicle handling is affected. The differ-
Clutch Overload ential lock switch (Fig. 8.21) allows the driver to lock
If the "TRANS TEMP" telltale light comes on while the wheels on the same axle together. The red differ-
driving and the current gear indicator begins to flash ential lock warning light illuminates on the dash mes-
between the current gear and "CO" (clutch overload), sage center when differential lock is engaged.
the clutch has begun to overheat.
The clutch overload may have been caused by im-
proper driving practices such as frequent and rapid
start/stop driving, or hillholding with the throttle pedal.
In this case, allow the clutch to cool, and continue
on, but cease the improper driving practices.
If the clutch overload message returns or continues,
the clutch is worn or damaged. Bring the vehicle at
once to a safe stopping place and call an authorized
Freightliner service facility for assistance. 10/26/2001 f610596
Low Hydraulic Fluid Level Fig. 8.21, Differential Lock Switch

IMPORTANT: The only hydraulic fluid permitted Differential lock provides maximum traction under
in this system is Pentosin CHF 11S. No other slippery conditions. When the differential lock is en-
fluid can be substituted. gaged, the clutch collar completely locks the differen-
tial case, gearing, and axle shafts together, maximiz-
If the "CHECK TRANS" telltale light comes on while
ing the traction of both wheels and protecting against
driving and the current gear indicator begins to flash
spinout.
between the current gear and "FL" (fluid level), there
has been an unusual loss of hydraulic fluid. Bring the Under normal traction conditions, do not use the dif-
vehicle at once to a safe stopping place and call an ferential lock feature.
authorized Freightliner service facility for assistance.
The hydraulic reservoir holds about 1.05 quarts (one
liter) of Pentosin CHF 11S.
8.30
Truck-Manuals.net
Drivetrain
Differential Lock Switch NOTE: If the vehicle is moving too fast, let up
slightly on the accelerator. As the vehicle slows,
CAUTION the wheels will lock.
Abnormal Response: If the LED blinks for more than
Differential lock should only be engaged when 30 seconds, the lock mechanism may not be fully
the vehicle is stopped or moving slowly at low engaged/disengaged. Bring the vehicle to an autho-
throttle. This will prevent internal axle damage. rized Freightliner service facility for testing.
Normally, when differential lock is available on dual-
drive vehicles, one switch activates the lock on both Differential Lock Operation
rear drive axles. As an option, it possible to have two
differential lock switches, one for the forward rear WARNING
and one for the rearmost drive axle. It is also pos-
sible for some vehicles to have differential lock on Locking the wheels when the vehicle is traveling
only one of the drive axles. down steep grades or when the wheels are slip-
ping could damage the differential and/or lead to
A two-position guarded rocker switch (Fig. 8.21) con-
loss of vehicle control, causing personal injury
trols differential lock, causing the wheels on each
and property damage.
axle governed by the switch to rotate together. To
lock the wheels together, press the upper half of the Lock the wheels only when the vehicle is standing
rocker momentarily (at the red LED). To unlock the still or moving at very low speed, less than 5 mph (8
wheels, press the upper half of the rocker again. km/h). Never lock the wheels when the vehicle is
traveling down steep grades or when the wheels are
IMPORTANT: The differential lock rocker switch
slipping.
is guarded to prevent unintentional switch acti-
vation. If the LED in the switch begins to blink NOTE: On some vehicles, the differential lock
during normal operation, when the switch has system is connected through the low speed
not been activated, this indicates an error condi- range of the transmission. If this system is used,
tion. Bring the vehicle to an authorized Freight- the transmission must be in the low speed
liner service facility as soon as possible. range for the wheels to fully lock.
When the differential lock switch is pressed, three
responses are possible: a normal response, a slow WARNING
response, and an abnormal response.
A vehicle with locked wheels can still slip side-
Normal Response: The LED in the switch blinks until ways, causing possible loss of vehicle control,
the axle has responded to the request to lock the personal injury, and property damage.
wheels. At this point, the LED comes on steady and
stays illuminated. In normal operation, the wheels Be especially careful when driving under slippery
may lock so quickly that the blinking of the switch is conditions with the wheels locked. Though forward
barely noticeable. traction is improved, the vehicle can still slip side-
ways.
If operation of the switch is not possible for any rea-
son (ignition is turned off, vehicle is moving faster If the vehicle is moving, maintain a constant vehicle
than 25 mph, etc.), the LED will stop blinking and speed when the differential lock is turned on. Briefly
turn off. let up on the accelerator to relieve torque on the
gearing, allowing the wheels to lock completely.
Slow Response: If operation of the switch is slowed When the wheels are fully locked, the turning radius
for any reason (vehicle moving too fast, low air pres- will increase because the vehicle understeers. See
sure, etc.), the switch will continue to blink until the Fig. 8.22. Drive cautiously and do not exceed 25
wheels are able to lock. As in the normal response, mph (40 km/h).
the LED comes on steady and stays illuminated once
the wheels have locked. To disengage differential lock after leaving poor road
conditions, operate the differential lock switch as dis-
cussed above while maintaining vehicle speed. Let
8.31
Truck-Manuals.net
Drivetrain
10/26/2001 f610595
02/09/96 f350079a
Fig. 8.23, Interaxle Lock Switch
A. Turning Radius When the Differential Lock is
Engaged (understeer condition) When the interaxle lock is not engaged, there is dif-
B. Turning Radius When the Differential Lock is
ferential action between the two axles. The differen-
Disengaged
tial compensates for different wheel speeds and
Fig. 8.22, Turning Radii variations in tire size. Keep the interaxle lock disen-
gaged when driving on roads where traction is good.
up momentarily on the accelerator to allow the
When the interaxle lock is engaged, the differential
wheels to fully unlock, then resume driving at normal
action between the two axles is locked. Both drive
speed.
axles now share the power. Both axles, and both
NOTE: If the differential lock system is con- sets of wheels, turn together at the same speed. The
nected with the transmission in its low speed interaxle lock should be used when the vehicle en-
range, shifting out of the low speed range will counters poor traction conditions; however, it also
also disengage the differential lock function. The increases drivetrain and tire wear and should be
switch will blink until the wheels unlock, and used only when improved traction is required.
then go out. Interaxle Lock Switch
Tandem Drive Axles With Interaxle A two-position guarded rocker switch (Fig. 8.23) con-
Lock trols interaxle lock, causing both axle shafts to rotate
together. To lock the axles together, press the upper
half of the rocker momentarily (at the red LED). To
CAUTION turn off interaxle lock, press the lower half of the
rocker (at the double-axle icon).
The interaxle lock should not be engaged on a
vehicle with obviously spinning wheels. Engage- IMPORTANT: The interaxle lock rocker switch is
ment at high speed or power can damage the guarded to prevent unintentional switch activa-
axle(s). tion. This switch does not have a diagnostic
Meritor has an interaxle lock (axle lock, interaxle dif- blink function when inactive.
ferential lockout) feature that is standard on all dual- When the interaxle lock switch is pressed, three re-
drive (tandem-drive) vehicles. Interaxle lock is recom- sponses are possible: a normal response, a slow re-
mended for use under adverse road conditions sponse, and an abnormal response.
where greater traction is needed. See the axle manu-
facturer’s manual provided with the vehicle for more Normal Response: The LED in the switch blinks until
information. the interaxle lock is engaged. At this point, the LED
comes on steady and stays illuminated. In normal
The interaxle lock switch (Fig. 8.23) allows the driver operation, the interaxle may lock so quickly that the
to lock both rear axles together. The red interaxle blinking of the switch is barely noticeable.
warning light illuminates on the dash message center
when interaxle lock is engaged.
8.32
Truck-Manuals.net
Drivetrain
If operation of the switch is not possible for any rea- when greater traction and maximum pulling power is
son (ignition is turned off, vehicle is moving too fast, needed at low engine speed (rpm).
etc.), the LED will stop blinking and turn off. Under normal operating conditions, the vehicle is op-
Slow Response: If operation of the switch is slowed erated using the high-speed gear ratios of the axle.
for any reason (by cold weather, low air pressure, Under extreme weather or off-road conditions, at low
etc.), the switch will continue to blink until the axles speed and rpm and/or to pull heavy loads, the ve-
lock together, or for a maximum of 10 seconds. As in hicle must be operated using the low-speed, or re-
the normal response, the LED comes on steady and duction, gear ratios of the axle.
stays illuminated.
Axle Shift Switch
30 seconds, the lock mechanism may not be fully The axle shift switch is a two-position guarded rocker
engaged/disengaged. Bring the vehicle to an autho- switch (Fig. 8.24) installed on vehicles with two-
rized Freightliner service facility for testing. speed axles.
Interaxle Lock Operation

To engage interaxle lock and achieve maximum pull-
ing power in slippery or hazardous road conditions,
operate the interaxle lock switch as discussed above,
while maintaining vehicle speed. Let up momentarily
on the accelerator until the axle lock engages. Pro-
ceed over poor road conditions with caution. Do not
wait until traction is lost and the tires are spinning
before engaging the interaxle lock.
10/26/2001 f610594
CAUTION Fig. 8.24, Axle Shift Switch
Do not turn on the interaxle lock switch when the To shift the axle from low speed to high speed, press
tires are slipping. Do not continuously operate the upper half of the rocker momentarily (at the
the vehicle with the interaxle lock engaged dur- LED). To turn the axle shift off (switch from high
ing good road conditions. To do so could result speed back to low speed), press the upper half of
in damage to the axle gearing and excessive tire the rocker again. When the axle has shifted speed,
wear. the LED turns off.
To disengage the interaxle lock after leaving poor When the panel lights are on, the AXLE SHIFT leg-
road conditions, operate the interaxle lock switch as end is backlit in green.
discussed above while maintaining vehicle speed.
Let up momentarily on the accelerator to allow the IMPORTANT: The axle shift rocker switch is
axles to fully unlock, then resume driving at normal guarded to prevent unintentional switch activa-
speed. tion. If the LED in the switch begins to blink dur-
ing normal operation, when the switch has not
Axle Shift been activated, this indicates an error condition.
Bring the vehicle to an authorized Freightliner
CAUTION service facility as soon as possible.
When the axle shift switch is pressed, three re-
To prevent transmission and axle damage, make sponses are possible: a normal response, a slow re-
sure the automatic transmission is in high range sponse, and an abnormal response.
when performing an axle shift with the vehicle
moving. Normal Response: The LED in the switch blinks until
the axle shifts speed. At this point, the LED comes
Axle shift is a function installed on vehicles with two-
on steady and stays illuminated. In normal operation,
speed axles to allow the use of the low speed range
8.33
Truck-Manuals.net
Drivetrain
the axle may shift so quickly that the blinking of the

switch is barely noticeable.
If operation of the switch is not possible for any rea-
son (interaxle lock is on, ignition is turned off, etc.),
the LED will stop blinking and turn off.
Slow Response: If operation of the switch is slowed
for any reason (by cold weather, low air pressure,
etc.), the switch will continue to blink until the axle
shifts. As in the normal response, the LED comes on
steady and stays illuminated.
30 seconds, the axle shift function/mechanism may
not be operating correctly. Bring the vehicle to an
authorized Freightliner service facility for testing.
Axle Switch Interlock

NOTE: On vehicles with tandem drive axles,
there is an interlock that prevents an axle from
shifting speed whenever the interaxle lock is on.
If the axle shift switch is pressed when the interaxle
lock is on, the axle shift will not be completed. The
LED does the following:
• If the LED is off, the LED comes on briefly and
turns off again.
• If the LED is on, it stays on.
To complete the axle shift, turn off the interaxle lock
and press the axle shift switch again. If still needed,
the interaxle lock can then be reactivated.
8.34
Truck-Manuals.net
9
Steering and Brake Systems
Steering System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1
Air Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1
Hydraulic Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4
Meritor WABCO® Antilock Braking System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5
Enhanced Stability Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.6
Truck-Manuals.net
Steering System ing wheel spokes should be at the 3 o’clock and 9

o’clock positions or within 10 degrees of these posi-
The power steering system includes the power steer- tions. See Fig. 9.1.
ing gear, hydraulic hoses, power steering pump, res-
ervoir, steering wheel and column, and other compo-
nents. Some models are also equipped with a
separate hydraulic power cylinder on the right side of
the front axle, or a right-hand slave gear.
The power steering pump, driven by the engine, pro-
vides the power assist for the steering system. If the
10° 10°
engine is not running, there is no power assist.
If the power-assist feature does not work due to hy- 1 2
draulic fluid loss, steering pump damage, or another
cause, bring the vehicle to a safe stop. Do not drive
the vehicle until the cause of the problem has been 10° 10°
corrected.
WARNING 05/10/2007 f462075
Driving the vehicle without the power-assist fea- 1. 9 o’Clock 2. 3 o’Clock

ture of the steering system requires much greater Fig. 9.1, Steering Wheel Centered
effort, especially in sharp turns or at low speeds,
which could result in an accident and possible On the optional 20-inch (500-mm) wheel, the steering
injury. wheel spokes should be at the 4 o’clock and 8
o’clock positions or within 10 degrees of these posi-
NOTICE tions. For steering wheel adjustment procedures, see
Group 46 of the Business Class® M2 Workshop
Never steam clean or high-pressure wash the Manual.
steering gear. Internal damage to gear seals, and
ultimately the steering gear, can result. Air Brake System
Drivers should carefully use the power available with A dual air brake system consists of two independent
a power steering system. If the front tires become air systems that use a single set of brake controls.
lodged in a deep hole or rut, drive the vehicle out Each system has its own reservoirs, plumbing, and
instead of using the steering system to lift the tires brake chambers. The primary system operates the
out of the hole. service brakes on the rear axle; the secondary sys-
tem operates the service brakes on the front axle.
NOTICE Service brake signals from both systems are sent to
the trailer.
Avoid turning the tires when they are against a
curb, as this places a heavy load on steering WARNING
components and could damage them.
Do not operate the vehicle with the front brakes
Steering Wheel Adjustment backed off or disconnected. Backing off or dis-
Two steering wheels are available: a standard 18- connecting the front brakes will not improve ve-
inch (450-mm) steering wheel and an optional 20- hicle handling and may lead to loss of vehicle
inch (500-mm) steering wheel. control, resulting in property damage or personal
injury.
When there is no load on the vehicle and the front
tires are pointed straight ahead, the standard steer-
9.1
Truck-Manuals.net
Air Brake System, General Air Brake System Operation

Information Before driving your vehicle, allow time for the air
The warning light and buzzer come on if air pressure compressor to build up a minimum of 100 psi (689
drops below 64 to 76 psi (441 to 524 kPa) in either kPa) pressure in both the primary and secondary
system. If this happens, check the dual system air systems. Monitor the air pressure system by observ-
pressure gauge to determine which system has low ing the dual system air pressure gauge and the low-
air pressure. Although the vehicle’s speed can be air-pressure warning light and buzzer. The warning
reduced using the brake pedal, either the front or light and buzzer shut off when air pressure in both
rear service brakes will not be operating at full ca- systems reaches 64 to 76 psi (441 to 524 kPa).
pacity, causing a longer stopping distance. Bring the IMPORTANT: Before driving the vehicle, secure
vehicle to a safe stop and have the air system re- all loose items in the cab so that they will not fly
paired before continuing. forward during a full brake application. Make
IMPORTANT: In the event of a total loss of ser- sure all passengers are wearing seat belts.
vice brakes with full system air pressure, use During normal brake stops, depress the brake pedal
the parking brake control valve (yellow knob) to until braking action slows down the vehicle. Increase
bring the vehicle to a complete stop in the saf- or decrease the pressure on the pedal so that the
est location possible. vehicle comes to a smooth, safe stop. Apply the
Before a vehicle with insufficient system air pressure parking brake if the vehicle is to be parked.
can be moved, the spring parking brakes must be IMPORTANT: An air brake proportioning system
released by applying an external air source at the may be used in tractor air brake systems when
gladhands, or by manually caging the parking brake the vehicle is not equipped with antilock braking
springs. system (ABS). When operating in bobtail mode,
the rear brake chambers (on which the axle
WARNING load has been greatly reduced) receive reduced
(proportional) air pressure, while the front axle
Do not release the spring parking brakes and
brake chambers receive full (normal) air pres-
then drive the vehicle. There would be no means
of stopping the vehicle, which could result in se- sure. This results in a different brake pedal
rious personal injury or vehicle damage. Before "feel," as the pedal seems to require more travel
releasing the spring parking brakes, make the and/or effort to slow or stop the vehicle. How-
connection to a towing vehicle or chock the tires. ever, the air brake proportioning system actually
improves vehicle control when the tractor is in
After correcting the brake system problem, uncage
the spring parking brakes before resuming normal bobtail mode. When the tractor is towing a
vehicle operation. trailer, the rear brake chambers will receive full
(normal) application air pressure.
Primary Air Brake System When parking a vehicle attached to a trailer that
Loss of air pressure in the primary air system causes does not have spring parking brakes, apply the trac-
the rear service brakes to become inoperative. The tor parking brake. Chock the trailer tires before dis-
secondary air system will continue to operate the connecting the vehicle from the trailer.
front brakes and the trailer brakes (if equipped).
WARNING
Secondary Air System
If a trailer or combination vehicle is not equipped
Loss of air pressure in the secondary air system with spring parking brakes, do not park it by pull-
causes the front axle brakes to become inoperative. ing out only the trailer air supply valve knob.
The primary air system will continue to operate the This would apply only the trailer service brakes.
rear service brakes and the trailer brakes (if If air were to bleed from the trailer brake system,
equipped).
9.2
Truck-Manuals.net
the trailer brakes would release, possibly causing 65 psi (448 kPa), the trailer air supply valve must be
an unattended runaway vehicle. pushed in. It should stay in to charge the trailer air
supply system and to release the trailer spring park-
NOTICE ing brakes.
Pull the trailer air supply valve out before disconnect-
Never apply the service and spring parking ing a trailer or when operating a vehicle without a
brakes simultaneously. To do so transmits exces- trailer. If pressure in both air systems drops to 35 to
sive input force to the brake components, which 45 psi (242 to 310 kPa), the trailer air supply valve
could damage or cause eventual failure of brake automatically pops out, exhausting the trailer air sup-
actuating components. ply, and applying the trailer service or spring parking
brakes.
Brake Controls
The trailer brake lever (hand control valve) is used
for applying the trailer brakes without applying the 1
2
truck or tractor service brakes. It is usually mounted
on the right-hand control panel. See Fig. 9.2. The
valve can be partially or fully applied, but in any par-
tially applied position, it will be overridden by a full
application of the brake pedal. Moving the lever
down applies the trailer brakes, while moving it up
releases the trailer brakes. The lever will automati-
cally return to the up position when it is released. 03/10/99 f610291
1. Trailer Air-Supply-Valve Knob
WARNING 2. Parking-Brake-Valve Knob
Fig. 9.3, Brake Valve Knobs
Do not use the trailer service brakes for parking;
they are not designed for this purpose. If air The yellow diamond-shaped knob in the control
bleeds out of the trailer air tank during parking, panel actuates the parking brake valve. See Fig. 9.3.
the vehicle could roll, causing serious personal Pulling out the parking brake valve applies both the
injury or property damage. tractor and trailer parking brakes and automatically
causes the trailer air supply valve to pop out.
NOTICE
Do not use the spring parking brakes if the ser-
vice brakes are hot, such as after descending a
steep grade. To do so could damage the brakes.
Allow hot brakes to cool before using the spring
parking brakes.
Do not use the spring parking brakes during
freezing temperatures if the service brakes are
wet. To do so could cause them to freeze. If the
brakes are wet, drive the vehicle in low gear and
10/17/2001 f610591 lightly apply the brakes to heat and dry them.
Fig. 9.2, Trailer Brake Lever If the trailer is not equipped with spring parking
brakes, pulling out the parking brake valve applies
The red octagonal-shaped knob in the control panel the tractor parking brake and the trailer service
actuates the trailer air supply valve. See Fig. 9.3. brakes. When the tractor and trailer parking brakes
After the vehicle’s air hoses are connected to a (or trailer service brakes) are both applied, the trailer
trailer and the pressure in both air systems is at least
9.3
Truck-Manuals.net
brakes are released by pushing in the trailer air sup-

ply valve, leaving the tractor parking brake applied. A
Air pressure in the primary or secondary reservoir
must be at least 65 psi (448 kPa) before the tractor
spring parking brakes, or the trailer service or spring
parking brakes, can be released.
Automatic Slack Adjusters

Automatic slack adjusters should never be manually
adjusted except during routine maintenance of the
foundation brakes (e.g., replacing shoes), during
slack adjuster installation, or in an emergency situa- B
tion.
When the brake pushrod stroke exceeds the legal
brake adjustment limit on a vehicle, there is likely a
mechanical problem with the foundation brake com- 04/26/2012 f460513a
ponents or the adjuster is improperly installed.
A. Open caps and check fluid level.
Visit a repair facility as soon as possible when B. Fill to this level.
brakes equipped with automatic slack adjusters are
determined to be out of adjustment. Fig. 9.4, Hydraulic Brake Reservoir
The brake system warning light illuminates if there is

WARNING a problem within the system. Bring the vehicle to a
safe stop and correct the problem before continuing
Manually adjusting an automatic slack adjuster to operation of the vehicle. See Group 42 of the
bring the pushrod stroke within legal limits is Business Class® M2 Workshop Manual for hydraulic
likely masking a mechanical problem. Adjustment brake system troubleshooting and adjustment proce-
is not repairing. Before adjusting an automatic dures.
slack adjuster, troubleshoot the foundation brake
system and inspect it for worn or damaged com- Hydraulic Brake System Operation
ponents. Improperly maintaining the vehicle brak-
ing system may lead to brake failure, resulting in IMPORTANT: Make sure that the fluid level in
property damage, personal injury, or death. the master cylinder reservoir is up to the ridge
that surrounds the reservoir. See Fig. 9.4. Use
Hydraulic Brake System only heavy-duty brake fluid, DOT 3 or DOT 4, in
the hydraulic brake system.
Hydraulic Brake System, General IMPORTANT: Before driving the vehicle, secure
Information all loose items in the cab so that they will not fly
The hydraulic brake system includes a power forward during a full brake application. Make
booster, master cylinder, reservoir, hydraulic lines, a sure all passengers are wearing seat belts.
brake rotor on each wheel hub, and a brake caliper During normal brake stops, depress the brake pedal
and pad assembly at each rotor. until braking action slows down the vehicle. Increase
The master cylinder controls braking power to the or decrease the pressure on the pedal so that the
front and rear brakes. The Bendix Hydro-Max® vehicle comes to a smooth, safe stop. Apply the
power booster is attached to the rear of the master parking brake if the vehicle is to be parked.
cylinder and is connected to the power steering sys- When parking a vehicle attached to a trailer, apply
tem (which provides pressurized power steering the tractor parking brake. Chock the trailer tires be-
fluid). An electrical backup pump operates if there is fore disconnecting the vehicle from the trailer.
inadequate fluid flow from the power steering pump
to the power booster.
9.4
Truck-Manuals.net
Meritor WABCO® Antilock The Meritor WABCO ABS combines one front-axle
control channel with one rear-axle control channel to
Braking System form one control circuit. For example, the sensor and
modulator valve on the left-front axle form a control
The Meritor WABCO Antilock Braking System (ABS) circuit with the sensor and modulator valve on the
is an electronic wheel speed monitoring and control right-rear axle.
system that works with the brake system. ABS pas-
sively monitors vehicle wheel speed at all times, and The ECU has a safety circuit that constantly monitors
controls wheel speed during emergency stops or the wheel sensors, traction control valve (if
wheel lock situations. equipped), modulator valves, and the electrical cir-
cuitry. If the safety circuit senses a failure in any part
of the ABS, the tractor warning lamp (TRACTOR
NOTICE ABS) illuminates and the control circuit where the
An accumulation of road salt, dirt, or debris on failure occurred is switched to normal braking action.
the ABS tone wheels and sensors can cause the The remaining control circuit will retain the ABS ef-
ABS warning light to come on. If the ABS light fect. Even if the ABS is completely inoperative, nor-
does come on, the tone rings and sensors mal braking ability is maintained.
should be inspected for corrosion and serviced if The ABS indicator lamp illuminates after the ignition
necessary. The service should include cleaning is switched on and will go out within three seconds if
of the tone rings and sensors. If any tone ring on the system is functioning correctly. If the ABS indica-
a vehicle shows severe corrosion, all tone rings tor lamp does not illuminate, or does not go out after
on that vehicle should be replaced. three seconds, have the vehicle serviced before
During winter months in areas where corrosive operation.
materials are used on the highways, periodically During emergency or reduced-traction stops, fully
clean the underside of the vehicle, including the depress the brake pedal until the vehicle comes to a
tone rings and sensors, to ensure proper ABS safe stop. Do not pump the brake pedal. With the
function and to protect the components from cor- brake pedal fully depressed, the ABS will control all
rosion. Clean more frequently when unusually wheels to provide steering control and a reduced
corrosive chemicals are being used. braking distance.
IMPORTANT: For proper ABS system operation, Although the ABS improves vehicle control during
do not change tire sizes. The sizes of the tires emergency braking situations, the driver still has the
installed during production are programmed into responsibility to change driving styles depending on
the electronic control unit (ECU). Installing existing traffic and road conditions. For example, the
different-sized tires could result in a reduced ABS cannot prevent an accident if the driver is
braking force, leading to longer stopping dis- speeding or following too closely.
tances.
Trailer ABS Compatibility
The ABS includes signal-generating tone wheels and
sensors located in the wheel hubs of each sensed The Meritor WABCO ABS is designed to communi-
wheel. The sensors transmit vehicle wheel speed cate with a trailer ABS, if they are compatible. Com-
information to an electronic control unit ECU located patibility will result in the illumination of the TRAILER
behind the center dash. The ECU’s main circuit inter- ABS lamp during vehicle start-up and fault detection.
prets the speed sensor signals and calculates wheel The TRAILER ABS lamp will not illuminate unless a
speed, wheel retardation, and a vehicle reference compatible trailer is connected to the tractor. The
speed. If the calculations indicate wheel lockup, the dash-mounted lamp will operate as follows when a
main circuit signals the appropriate modulator valve compatible trailer is properly connected to the tractor:
to reduce braking pressure. During emergency brak-
ing, the modulator valve alternately reduces, in- • When the ignition key is turned to the ON posi-
creases, or maintains air pressure supply in the tion, the TRAILER ABS lamp will illuminate mo-
brake chamber to prevent front and rear wheel mentarily, then turn off.
lockup.
9.5
Truck-Manuals.net
• If the lamp illuminates momentarily during ve- minate for about three seconds. After three seconds,
hicle operation, then shuts off, a fault was de- the warning lights go out if all of the tractor’s ABS
tected and corrected. components are working.
• If the lamp illuminates and stays on during ve- IMPORTANT: If any of the ABS warning lights
hicle operation, there is a fault with the trailer do not work as described above, or illuminate
ABS. Repair the trailer ABS system immedi- while driving, repair the ABS immediately to en-
ately to ensure full antilock braking capability. sure full antilock braking capability.
IMPORTANT: If a compatible trailer is con-
nected, and the lamp is not illuminating momen- Enhanced Stability Control
tarily when the ignition key is turned to the ON
position, it is possible that the lamp is burnt out. WARNING
Automatic Traction Control Enhanced Stability Control (ESC) is intended only
Vehicles with electronic engines and ABS may have as an aid for a conscientious and alert driver.
Automatic Traction Control (ATC). On these vehicles, Carefully read the information in this manual to
the ATC system automatically limits wheel spin dur- understand this system and its limitations. ESC
ing reduced-traction situations. In normal braking ap- is not a substitute for safe driving procedures.
plications, the standard air brake system is in effect. Failure to drive safely, and use the system prop-
erly, could result in personal injury and/or death
An additional solenoid valve is installed. During and property damage.
reduced-traction situations, the ATC solenoid valve
controls air pressure to the modulator valves and ESC automatically reduces engine power, applies the
they in turn increase, hold, or reduce pressure to the engine brake, and/or applies the tractor and trailer
appropriate brake chambers to provide better traction brakes when the acceleration sensor detects that the
whenever wheel spin occurs. vehicle is at risk of rolling over. In addition, ESC of-
fers the added capability of complete directional sta-
When the ATC system is in the NORMAL mode, it bility (yaw control) in oversteer and understeer condi-
will apply gentle braking to the spinning wheel, to tions to reduce the likelihood of drift-out or jackknife.
feed power to the wheel(s) with better traction. If The system determines where the driver is attempt-
both wheels are spinning, the system will signal the ing to steer the vehicle and how much brake demand
engine to reduce power. is required in order to more precisely control the ve-
ATC includes a deep snow and mud option to in- hicle in an emergency situation.
crease available traction on extra soft surfaces like ESC works by constantly comparing the driver’s in-
snow, mud, or gravel. A momentary contact rocker tention with the vehicle’s actual behavior. The system
switch labeled ATC will be located on the dash. does this by monitoring systems such as wheel
Pressing the switch will temporarily allow more wheel speed, steering angle, yaw rate, lateral acceleration,
spin. The activation of the deep snow and mud op- throttle position, and brake application. A central mi-
tion is indicated by a flashing WHEEL SPIN lamp. crocomputer analyzes the collected data and triggers
Pressing the switch again will cycle the system back a response to keep the vehicle on course when an
to normal operation. unstable condition is detected.
The roll stability control system automatically reduces
NOTICE engine power, applies the engine brake, and/or ap-
The deep snow and mud option is intended to be plies the tractor and trailer brakes when the accelera-
used under specific slippery conditions that re- tion sensor detects that the vehicle is at risk of rolling
quire momentary increased wheel spin. Using over. The control can intervene even before an advi-
this option for an extended period of time may sory message is displayed.
damage the vehicle brake system. When the system detects that the vehicle is at risk of
After the ignition switch is turned on, the TRACTOR oversteering or understeering, it applies individual
ABS lamp and the WHEEL SPIN indicator lamp illu- tractor wheel end brakes and trailer brakes, activates
9.6
Truck-Manuals.net
the engine brake (if equipped), and/or cuts engine

power, depending on the severity. As a result, the
driver has full control over the vehicle until the sys-
tem detects a potential risk and intervenes accord-
ingly. ESC operates automatically; the driver does
not monitor or activate the system.
9.7
Truck-Manuals.net
10
Fifth Wheels and Trailer
Couplings
Fifth Wheels, General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1
Fifth Wheel Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1
Fifth Wheel Uncoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4
Fifth Wheel Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7
Truck-Manuals.net
Fifth Wheels and Trailer Couplings
Fifth Wheels, General Fifth Wheel Lubrication

Information
WARNING
WARNING Keep the fifth wheel plate lubricated to prevent
binding between the tractor and trailer. A binding
Do not use any fifth wheel that fails to operate fifth wheel could cause erratic steering and loss
properly. Doing so may cause loss of vehicle of vehicle control, possibly resulting in personal
control, possibly resulting in severe personal in- injury or death.
jury or death.
The standard fifth wheel plate must be kept well lu-
Air-Suspension Dump Valve bricated with chassis grease to prevent friction and
binding between the tractor fifth wheel plate and the
The air-suspension dump valve may be used to ad- trailer.
just the tractor height to aid with coupling to or un-
For a low-lube fifth wheel plate, inspect the condition
coupling from a trailer. See Fig. 10.1. When the
of the low-lube pads. There should be no damaged
switch is set to LOWER, the air-suspension dump
or missing pieces. Slight puckering at the outside
valve deflates the air springs to lower the rear of the
edges is normal.
vehicle. In the AUTO position, the automatic ride-
control valves operate for normal driving. For lubrication instructions, see Group 31 of the
Business Class M2 Maintenance Manual.
WARNING
Fifth Wheel Coupling
Never exhaust air from the suspension while
driving. The suspension will not absorb road Fifth wheel coupling is activated with the lock control
shocks, possibly damaging components, and ve- handle located on either the right side or left side of
hicle handling may be compromised. This could the fifth wheel. Coupling has successfully occurred
result in loss of vehicle control, possibly result- when the kingpin has been forced into the jaws and
ing in severe personal injury or death. the lock control handle has moved to the locked
position.
NOTICE
NOTICE
Do not operate the vehicle over uneven ground
such as ramps, speed bumps, curbs, etc. with Some fifth wheels may be mounted on sliding
the air springs deflated. Doing this may lead to rails. Before attempting to couple a trailer to a
air bag separation from the piston, preventing the sliding fifth wheel, the slide feature must be
suspension air springs from inflating. locked to prevent the top plate from sliding rap-
idly forward or rearward, causing damage to the
fifth wheel or kingpin.
Fontaine and Holland Fifth Wheels

Coupling
1. Chock the front and rear of the trailer tires to
prevent the trailer from moving.
2. Ensure the fifth wheel jaw is fully open and the
operating rod is in the unlocked position. See
10/26/2001 f610597 Fig. 10.2 or Fig. 10.3.
Fig. 10.1, Air-Suspension Dump Valve

3. Make sure the fifth wheel top plate is tilted so the
ramps are as low as possible.
10.1
Truck-Manuals.net
1
1
2
1 1
3
B
2
10/26/2010 f310110a
NOTE: Make sure the safety latch is down when the 11/02/2010 f310447
control handle is locked. 1. Safety Latch
A. Unlocked B. Locked 2. Operating Rod (locked)
3. Operating Rod (unlocked)
1. Safety Latch 2. Lock Control Handle
Fig. 10.3, Holland Simplex SE Locking Mechanism
Fig. 10.2, Fontaine Locking Mechanism
4. Position the tractor so that the center of the fifth D

wheel is in line with the trailer kingpin. The king-
C A
pin should be in a position to enter the throat of
the locking mechanism.
NOTICE
Attempting to couple at the wrong height may B
cause improper coupling, which could result in
damage to the fifth wheel or kingpin.
10/28/2010 f311124
5. Adjust the trailer height if required. A. Fifth wheel must lift C. Ramps tilted down
For a standard fifth wheel plate, the trailer trailer D. 4 to 8 inches
should contact the fifth wheel approximately 4 to B. Adjust trailer height
8 inches (10 to 20 cm) behind the fifth wheel Fig. 10.4, Trailer Connection Point, Standard Fifth
pivot. See Fig. 10.4. Wheel
For a low-lube fifth wheel plate, the fifth wheel
prevent from hitting the kingpin too hard, then
must slide freely under the trailer, and the trailer
resume backing slowly until the fifth wheel locks.
should contact the fifth wheel at the pivot. See
Fig. 10.5. On a standard fifth wheel, the fifth wheel must lift
the trailer.
6. With the fifth wheel lock opening aligned with the
trailer kingpin, back the tractor slowly toward the On a low-lube fifth wheel, do not lift the trailer as
trailer. After sliding under the trailer, STOP to this may damage the fifth wheel plate.
10.2
Truck-Manuals.net
A B
09/10/2010 f311126
A. No gap between trailer B. Kingpin inside lock
and fifth wheel
A
Fig. 10.6, Coupling Inspection
09/10/2010 f311125
A. Adjust trailer height B. Ramps tilted down
NOTICE
Fig. 10.5, Trailer Connection Point, Low-Lube Fifth Always make sure the connection hanger keeps
Wheel the trailer air hoses and electrical cables posi-
tioned so that they do not rub on anything. Rub-
7. Apply the tractor parking brakes. bing may wear through hoses or cables, resulting
in air leaks, or exposed or broken wires, poten-
WARNING tially affecting trailer brake or electrical systems.
11. Charge the air brake system with air, checking
A visual inspection is required by law. Some im- that the air connections do not leak.
proper couplings can pass a pull test. Sound is
not reliable. Get out of the cab and look. Incor-
rect coupling could cause the trailer to discon- WARNING
nect, possibly resulting in serious personal injury
or death. Incorrect fifth wheel lock adjustment could cause
the trailer to disconnect, possibly resulting in se-
8. Perform a coupling inspection, checking that rious personal injury or death.
there is no gap between the bottom of the trailer
and the fifth wheel, and that the kingpin is se- 12. With the trailer wheels chocked and the brakes
curely locked. See Fig. 10.6 set, check for clearance between the kingpin and
the fifth wheel jaws by moving the tractor forward
When lockup has occurred, the fifth wheel con- and backward against the locked kingpin. If slack
trol handle moves to the locked position. Make is present, uncouple the trailer and have the fifth
sure that the safety latch is down over the lock wheel inspected and adjusted by a certified
control handle to hold the control handle in the technician.
locked position. (The safety latch will only rotate
down if the operating rod is fully retracted in the Jost Fifth Wheel Coupling
locked position.) See Fig. 10.2 for Fontaine fifth
wheels. See Fig. 10.3 for Holland fifth wheels. 1. Tilt the ramp down.
9. Release the tractor parking brakes. Test for king- 2. Open the kingpin locks. See Fig. 10.7.
pin lockup slowly inching the tractor forward, pull- 3. Back the vehicle close to the trailer, centering the
ing on the trailer against the chocks.
kingpin on the fifth wheel.
10. After lockup is completed, connect the tractor-to-
4. Chock the trailer wheels.
trailer air system lines and the electrical cable to
the trailer. Take care to prevent dirt or foreign 5. Connect the air lines and electrical cable.
material from entering the air system lines.
6. Ensure that the red trailer air supply valve (trailer
brake) is pulled out, and that the trailer parking
10.3
Truck-Manuals.net
nect, possibly resulting in serious personal injury

or death.
A 10. Apply the tractor parking brake, then perform a
physical check for positive kingpin lockup, and
that there is no gap between the trailer and the
fifth wheel. See Fig. 10.6.
11. Ensure that the release handle is in the locked
position adjacent to the casting. See Fig. 10.8.
12. Release the tractor parking brakes and test for
kingpin lockup by slowly moving the tractor for-
09/10/2010 f311128 ward, pulling on the trailer against the chocks.
A. Lock held open by catch mechanism
Fifth Wheel Uncoupling
Fig. 10.7, Jost Release Handle Unlocked
Manual Uncoupling
brakes are set. See Chapter 5 in this manual for
operation of the dash-mounted brake controls. 1. Apply the tractor and trailer parking brakes.
2. Chock the trailer rear wheels.
NOTICE 3. Lower the trailer landing gear until the weight is
Attempting to couple at the wrong height may removed from the fifth wheel.
cause improper coupling, which could result in 4. Disconnect the tractor-to-trailer air system lines
damage to the fifth wheel or kingpin. and electrical cable. Plug the air lines to prevent
7. Adjust the trailer height (if required). dirt or foreign material from entering the lines.
For a standard fifth wheel plate, the trailer 5. Verify that both the yellow parking-brake and red
should contact the fifth wheel approximately 4 to trailer-air-supply knobs are out, the tractor and
8 inches (10 to 20 cm) behind the pivot. See trailer parking brakes are set, and that the trailer
Fig. 10.4. is prepared for uncoupling.
For a low-lube fifth wheel plate, the fifth wheel 6. Release the kingpin locking mechanism following
must slide freely under the trailer, and the trailer the instructions for each manufacturer below.
should contact the fifth wheel at the pivot. See 6.1 Fontaine: Lift the safety latch and pull the
Fig. 10.5. lock control handle to the unlocked posi-
8. Back the tractor under the trailer. tion.
On a standard fifth wheel, the fifth wheel must lift 6.2 Holland: In the locked position the safety
the trailer. indicator swings freely over the operating
rod. See Fig. 10.9, View A.
On a low-lube fifth wheel, do not lift the trailer as
this may damage the fifth wheel plate. To unlock the mechanism, manually rotate
the safety indicator toward the rear of the
9. After sliding under the trailer, STOP to prevent fifth wheel. See Fig. 10.9, View B.
from hitting the kingpin too hard, then resume
backing slowly until the fifth wheel locks. Pull the operating rod out. When the
upper operating rod shoulder is outside
the slot, raise the handle and place the
WARNING shoulder of the upper rod against the plate
casting, above the slot. See Fig. 10.9,
A visual inspection is required by law. Some im-
View C.
proper couplings can pass a pull test. Sound is
not reliable. Get out of the cab and look. Incor-
rect coupling could cause the trailer to discon-
10.4
Truck-Manuals.net
OK OK
09/10/2010 f311127
Fig. 10.8, Jost Release Handle Locked
The fifth wheel is now in the lockset posi- been uncoupled and coupled again. Failure to do
tion and is ready for uncoupling. As the so may result in separation of the trailer from the
tractor pulls away from the trailer the king- tractor, possibly causing serious personal injury
pin forces the jaw to rotate, contacting the or death.
lock. Continued rotation of the jaw forces
the lock to move outward, and drops the Preparing the Trailer for Uncoupling
upper rod back into the slot. See Fig. 10.9
View D. The wheel is now ready for Before using the air valve to unlock a fifth wheel
coupling. kingpin, prepare the trailer as follows.
1. Apply the tractor and trailer parking brakes.
6.3 Jost: Pull the retractable handle out, then
secure it in the open position with the 2. Chock the trailer rear wheels.
catch.
3. Lower the trailer landing gear until the weight is
7. Release the tractor parking brake then drive out removed from the fifth wheel.
slowly, allowing the trailer to slide down the fifth
wheel and pick-up ramps. 4. Disconnect the tractor-to-trailer air lines and elec-
trical cable. Plug the air lines to prevent dirt or
Air-Actuated Uncoupling foreign material from entering the lines.
An air-actuated kingpin release valve is optional with Fontaine and Holland Fifth Wheels Air-
all fifth wheels. See Fig. 10.10. Activated Kingpin Unlock
NOTE: In the event of an air system failure, air- 1. Verify that both the yellow parking-brake and red
actuated kingpins can be manually released fol- trailer-air supply knobs are out, the tractor and
lowing the instructions for manual unlocking. trailer parking brakes are set, and that the trailer
is prepared for uncoupling.
WARNING NOTE: On Fontaine and Holland fifth wheels, if
the tractor parking brake is not set, the air-
Once the kingpin release valve has been pulled actuated kingpin-release valve will not activate.
the kingpin lock is released. The vehicle MUST
NOT be driven with the trailer until the trailer has
10.5
Truck-Manuals.net
1
4
A 2 C
B D
11/02/2010 f311133
A. Locked Position C. Lockset Position (upper rod resting against casting
B. Unlatched Position (safety indicator rotated towards the above slot)
rear of the fifth wheel) D. Open Position (ready for recoupling)
1. Safety Indicator 3. Upper Rod
2. Operating Rod 4. Plate Casting
Fig. 10.9, Holland Kingpin Locking Mechanism
2. Pull and hold the kingpin release valve until the Jost Fifth Wheels Air-Activated Kingpin
kingpin lock mechanism opens and locks in Unlock
place. See Fig. 10.10.
1. Verify that both the yellow parking-brake and red
3. Release the pull valve. trailer-air-supply knobs are out, the tractor and
4. Release the tractor parking brake. trailer parking brakes are set, and that the trailer
is prepared for uncoupling.
5. Drive out from under the trailer.
10.6
Truck-Manuals.net
The maximum axle weight ratings are shown on the

Federal Motor Vehicle Safety Standard (FMVSS)
label or Canadian Motor Vehicle Safety Standard
(CMVSS) label attached to the left rear door post of
the tractor. The desired load on the axle is no less
than 80 percent of the maximum axle weight rating,
but in no instances should the axle load exceed the
maximum axle weight rating given on the FMVSS or
CMVSS label.
Manual Slide Operation

The manual slide feature is operated from the fifth
wheel plate with a manual release handle using the
10/26/2010 f611102 following procedure. See Fig. 10.11.
Fig. 10.10, Air-Actuated Kingpin Release Valve 1
NOTE: With Jost fifth wheels, if the trailer park-
ing brake is not set the air-actuated valve will
not activate.
2. Release the tractor parking brake.
3. Pull and hold the kingpin release valve, then
drive forward slowly.
4. After the trailer has slid down the fifth wheel and
pick-up ramps, release the pull valve.
Fifth Wheel Slide

WARNING
2
Adjust the fifth wheel slide correctly, and do not 07/25/95 f310190
overload any tractor axle by incorrectly loading 1. Locking Wedge
the trailer. Incorrect slide adjustment or improper 2. Slide Release Pull Handle
axle loading could cause erratic steering and
loss of vehicle control, possibly resulting in seri- Fig. 10.11, Manual Release Sliding Fifth Wheel
ous personal injury or death. (Fontaine shown)
On sliding fifth wheel assemblies, the fifth-wheel 1. Stop the tractor and trailer in a straight line on
plate is attached to rails that allow forward and rear- level ground. Pull the red trailer air supply knob
ward movement of the fifth wheel to optimally distrib- to apply the trailer parking brakes.
ute the load across the axles. Slots are evenly 2. Apply the tractor parking brake, then release the
spaced along the slide rails, and retractable wedges sliding mechanism using the appropriate method
are positioned through the slots to hold the fifth for the fifth wheel manufacturer.
wheel in the desired position.
2.1 Fontaine: Lift the slide release pull handle
The amount of load distribution on the front steering to disengage it from the guide plate. Then,
axle and rear drive axle(s) will have a direct effect on pull out the handle until it is in the un-
the steering control of the vehicle. Determine the locked position and can be positioned
front and rear axle weights by weighing the vehicle against the guide plate to hold it out. The
on scales designed for this purpose.
10.7
Truck-Manuals.net
handle will stay in the unlocked position 5. Release the tractor parking brakes, then slowly
until it is manually disengaged from the move the tractor forward or backward until the
guide plate. See Fig. 10.12. fifth wheel is in the desired location.
NOTICE
When moving the fifth wheel to the desired posi-
tion, be sure the trailer landing gear will not at
any time come in contact with the tractor frame
or other components. Make sure that the front of
the trailer will not come in contact with the rear
of the cab or with other components if they ex-
tend beyond the rear of the cab.
WARNING
Check that the locking wedges have seated in the
slots. Failure to achieve complete lockup may
10/26/2010 f310050
allow disengagement of the tractor from the
trailer, possibly resulting in serious personal in-
Fig. 10.12, Releasing the Sliding Fifth Wheel, (Fontaine) jury or death.
2.2 6. Apply the tractor parking brakes, then lock the

Holland: Pull the operating rod out. Make
sure both side plungers have released. sliding member in position using one of the fol-
See Fig. 10.13. lowing methods:
6.1 Fontaine: Disengage the slide release
5 pull handle from the guide plate. The slide
4 release pull handle is spring-loaded in the
locked position and will seek the locked
6
position when disengaged from the guide
3 plate. After the slide release pull handle
returns to the fully locked position, visually
8 and physically check the locking wedges
3 to make sure they are fully inserted into
2 the slots in the slide rails. Make sure the
handle is locked in position against the
1 7
guide plate.
6.2 Holland: Raise the operating rod so that it
10/26/2010 f310445 is free to move inward. Make sure that the
lock pins have seated in the base plate
1. Baseplate 5. Slider Saddle Plate
2. Bolted Stop 6. Safety Latch rail holes and the operating rod moves
3. Baseplate Rail 7. Operating Rod into the locked position.
4. Fifth Wheel Mount 8. Operating Lever NOTE: The fifth wheel may need to be moved
Fig. 10.13, Sliding Fifth Wheel Manual Release, slightly to enable the locking wedges to enter
(Holland Simplex) the fully locked position.
3. Lower the trailer landing gear just enough to re-
move the weight from the tractor.
4. Chock the front and rear of the trailer tires to
prevent the trailer from moving.
10.8
Truck-Manuals.net
Air Slide Operation

The slide feature may be operated with an air switch
mounted in the dash, that operates an air cylinder
that locks and unlocks the slide. See Fig. 10.14.
02/22/2011 f611114
Fig. 10.14, Air-Slide Switch
1. Set the air-slide switch to UNLOCK. See

Fig. 10.14
Ensure the locking plungers have released. See
Fig. 10.15. B
For Jost fifth wheels, the mechanism activates as
09/10/2010 f311131
shown in Fig. 10.16.
A. Unlocked B. Locked
2. Lower the trailer landing gear just enough to re-
move the weight from the tractor. Fig. 10.16, Jost Sliding Fifth Wheel
1 3. Pull the red trailer-air-supply knob to set the

trailer-parking brakes.
4. Slowly move the tractor forward or backward
until the fifth wheel is in the desired location.
NOTICE
Ensure the trailer landing gear does not come in
contact with the tractor frame or other compo-
nents, and that the front of the trailer will not
come in contact with the rear of the cab or other
components if they extend beyond the rear of the
cab.
5. Apply the tractor parking brakes.
2 WARNING
07/25/95 f310189
1. Locking Wedge 2. Air Cylinder Check that the locking wedges have seated in the
slots. Failure to achieve complete lockup may
Fig. 10.15, Air-Operated Sliding Fifth Wheel (Fontaine
allow disengagement of the tractor from the
shown)
10.9
Truck-Manuals.net
trailer, possibly resulting in serious personal in-

jury or death.
6. Set the air-slide switch to LOCK. Visually inspect
the locking wedges or plungers to make sure
that they are fully inserted in the slide rail slots.
Verify that the plungers have engaged by tugging
the tractor forward while the trailer brakes are
locked and the wheels are chocked.
NOTE: The fifth wheel may need to be moved
slightly to enable the locking wedges to fully
lock.
10.10
Truck-Manuals.net
11
Pretrip and Post-Trip
Inspections and
Maintenance
Pre- and Post-Trip Inspection Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1
Daily Pretrip Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3
Weekly Post-Trip Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.11
Monthly Post-Trip Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.13
Truck-Manuals.net
Pretrip and Post-Trip Inspections and Maintenance
Pre- and Post-Trip Inspection Saddle Tank Areas Comp.

Drain air reservoirs (without automatic drain
Checklists 1
valves)
Regulations in Canada and the U.S. clearly indicate 2 Fuel tank(s) secure
that it is the driver’s responsibility to perform an in- 3 Frame rails and crossmembers
spection, and ensure the complete road-worthiness 4 Visible exhaust components
of a vehicle, before placing it into service. Commer-
cial vehicles may be subject to inspection by autho- Engine Compartment Comp.
rized inspectors, and an unsafe vehicle can be taken 1 Leakage under engine
out of service until the driver or owner repairs it. 2 Air intake system
Use the following checklists to ensure that vehicle 3 Engine oil level
components are in good working condition before 4 Power steering reservoir level
each trip. Careful inspections eliminate stops later to 5 Engine coolant level
fix overlooked or forgotten items. 6 Visible engine wiring
7 Frame rails
The checklists in this chapter can be copied and kept
as a record that the procedures have been com- Cab Comp.
pleted. For details on how to inspect each item on
Reset dash-mounted air intake restriction
the checklists, see the corresponding procedure 1
indicator
(step number) in this chapter.
2 Air-pressure warning system
NOTE: Checklists in this chapter correspond 3 Air governor cut-in and cut-out pressures
with the procedures and steps later in this chap- 4 Air pressure build-up time
ter. Your vehicle may not be equipped with all 5 Air system leakage
components listed below. 6 Air pressure reserve
8 Mirrors, windows, windshield
Checklists 9 Horn, windshield wipers, windshield washers
Daily Pretrip Inspection Checklists 10 Heater and defroster
11 Interior lights
See the following tables for a list of procedures that 12 Exterior lights
should be performed daily, before the first trip. Place 13 Seat belts and tether belts
a check mark in the complete (Comp.) column to 14 Fuel level
indicate a procedure has been performed. 15 Mirror adjustment
16 Service brakes
Inspector Date
Natural Gas Fuel System Inspection Comp.
1 Fuel tanks
Suspension and Slack Adjusters Comp. 2 Required decals
1 Suspension components 3 Vent caps
2 Slack adjusters Plumbing components, fuel fill fitting, fuel
4
lines
Wheels and Tires Comp. Fuel gauge components, fuel level sender
5
1 Wheel covers cable, LNG fuel tank pressure
2 Tire condition 6 Coolant hoses
3 Tire inflation 7 LNG fuel tank pressure
4 Rims and wheel components 8 LNG vaporizer
5 Wheel bearing oil seals and lubrication levels
6 Mud Flaps
11.1
Truck-Manuals.net
Weekly Post-Trip Inspection Checklist Natural Gas Fuel System Comp.

See the following table for procedures that should be 1 System leak test
performed weekly, post-trip. Place a check mark in 2 Drain CNG high-pressure fuel filter housing
the complete (Comp.) column to indicate a proce-
dure has been performed. Fluids Added
Use the following table to note any fluids that were
Inspector Date added during the inspection and maintenance proce-
dures.
Engine Compartment Comp. Fluids Added During Inspection

1 Windshield washer reservoir level Fluid Amount Added
2 Air intake restriction indicator Wheel Bearing Oil Seal
3 Automatic transmission fluid level Lubricant
4 Water in fuel/water separator Engine Oil
5 Steering components Power Steering Fluid
6 Serpentine drive belts Engine Coolant
Windshield Washer Fluid
Monthly Post-Trip Inspection Checklists Automatic Transmission
Fluid
See the following tables for procedures that should Hydraulic Clutch Fluid,
be performed monthly, post-trip. Place a check mark DOT4
in the complete (Comp.) column to indicate a proce-
dure has been performed.
Inspector Date
Brake Components Comp.

1 Brake system components
2 Brake chambers
3 Air brake lines
4 Flex air hoses
5 Brake linings and brake drums
6 Brake lining thickness
Driver-Side Saddle Tank Area Comp.

Drain air reservoirs (with automatic drain
1
valves)
2 Batteries
3 Aerodynamic components
Engine Compartment Comp.

1 Hood and bumper
2 Hydraulic clutch reservoir
3 Radiator and heater hoses
4 Steering wheel play
11.2
Truck-Manuals.net
Daily Pretrip Inspection and

Maintenance 4
5
Complete the following inspection and maintenance
6
procedures to ensure that vehicle components are in
good working condition before each trip. A driver who 7
3
is familiar with the vehicle and drives it regularly can 8
perform the daily inspections, then add the weekly
and monthly post-trip inspections as scheduled. 2 9
If the driver does not operate the vehicle on a con-
sistent basis, all daily, weekly, and monthly inspec- 1
tion and maintenance procedures should be per-
formed before the trip. 10
IMPORTANT: The pre- and post-trip checklists,

inspections, and maintenance procedures de- 06/17/2003 f421398
tailed in this chapter are not all-inclusive. 1. 7/16-inch Adjusting Nut
Refer to other component and body manufactur- 2. Grease Fitting
ers’ instructions for specific inspection and 3. Boot
maintenance instructions, as well as local, state, 4. Link
and federal guidelines. 5. Brake Chamber Piston Rod
6. Clevis
NOTE: If any system or component does not 7. 1/2-inch Clevis Pin
pass this inspection, it must be corrected before 8. 1/4-inch Clevis Pin
9. Grease Relief Opening
operating the vehicle. Whenever equipment re- 10. Slack Adjuster Spline
quires adjustment, replacement, and/or repair,
see the Business Class M2 Workshop Manual Fig. 11.1, Gunite Automatic Slack Adjuster
for procedures and specifications.
• Inspect slack adjuster boots, if equipped,
for cuts or tears.
Suspension and Slack Adjuster
Inspection • Inspect anchor straps, if equipped, for
damage.
Walk around the vehicle and visually inspect suspen-
• Look for worn clevis pins on brake cham-
sion and slack adjuster components.
ber pushrods.
1. Inspect the following suspension components for
• Look for missing or damaged cotter pins
signs of structural damage, cracks, or wear.
on the clevis pins.
• springs
• Ensure chamber piston rods are in line
• spring hangers with the slack adjusters.
• shocks
Wheel and Tire Inspection
• suspension arms
Walk around the vehicle and visually inspect each
• suspension brackets wheel and tire assembly.
• axle seats IMPORTANT: Wheel covers decrease drag force
• bushings as a vehicle moves, thereby improving fuel effi-
ciency. If replacement of a wheel cover is nec-
2. Inspect slack adjusters for signs of damage. See essary, the replacement cover must meet or ex-
Fig. 11.1, Fig. 11.2, or Fig. 11.3. ceed the drag reduction performance of the
11.3
Truck-Manuals.net
1
2
3
4
3
5
6
7
4 8 9
8
7
6
2
5
10/11/2005 A f421397
A. Rotate the control arm toward the brake chamber
until you can feel it contacting the internal stop.
1. Clevis
2. Slack Adjuster
3. Clevis Pin
4. Manual Adjusting Nut
9
5. Control Arm
1 10
6. Control-Arm Washers and Nut 01/31/2011 f422530
7. Anchor Strap Slot 1. Grease Fitting (if equipped)
8. Anchor Strap 2. Slack Adjuster Housing
9. Brake Chamber 3. Brake Chamber Pushrod
Fig. 11.2, Haldex Automatic Slack Adjuster 4. Clevis
5. Clevis Pin (large)
originally installed cover in order to maintain 6. Clevis Pin (small)
7. Actuator Rod
compliance with greenhouse gas and full effi- 8. Boot
ciency regulations (GHG14). 9. Manual Adjusting Nut
10. Camshaft Splines
1. If the vehicle was originally equipped with wheel
covers, ensure all wheel covers are present. In- Fig. 11.3, Meritor Automatic Slack Adjuster
spect wheel covers for damage or wear. Remove
wheel covers from rear drive wheels, if equipped, retaining ring so that the Velcro strips line up
prior to inspecting the tires and wheel compo- between the face cover and the liner. Make cer-
nents. tain the detachable view cover is centered on
NOTE: During wheel cover installation, ensure the face cover, and the Velcro strips are
the V-notch in the liner inner retaining ring is pressed firmly in place.
centered on the valve stem. The inner and outer 2. Inspect each tire for the following:
retaining rings should be uniformly aligned to
• valve stem caps on every tire, screwed on
each other and to the wheel rim. The outer re-
finger-tight
taining ring of the liner is equipped with two
canvas flaps. When installing the face cover, • bulges, cracks, cuts, and penetrations
make sure the cover retaining ring is inserted • oil contamination (petroleum derivatives will
between the two canvas flaps on the liner outer soften the rubber and destroy the tire)
11.4
Truck-Manuals.net
• tread depth—if tread is less than 4/32 inch Consult the rim or wheel manufacturer for the
(3 mm) on any front tire, or less than 2/32 correct tire inflation pressure for the vehicle
inch (1.5 mm) on any rear tire, replace the load.
tire
4. Examine each rim and wheel component. Check
• debris lodged between duel tire sets the wheel nuts or rim nuts for indications of
IMPORTANT: Low-rolling resistance (LRR) tires looseness.
minimize wasted energy as a tire rolls, thereby 4.1 Remove all dirt and debris from the as-
decreasing rolling effort and improving fuel effi- sembly. Rust streaks or metal build-up
ciency. If tire replacement is necessary, replace- around stud holes, or out-of-round or worn
ment tires must meet or exceed the rolling resis- stud holes, may be caused by loose wheel
tance of the originally installed tires in order to nuts.
maintain compliance with greenhouse gas and
full efficiency regulations (GHG14). WARNING
Contact your tire manufacturer/supplier to deter- Have any worn or damaged wheel components
mine the rolling resistance of the originally in- replaced by a qualified person using the wheel
stalled tires. Visit www.epa.gov/smartway for manufacturer’s instructions and the wheel indus-
additional information and resources. try’s standard safety precautions and equipment.
Otherwise a vehicle or workshop accident could
3. Check tire inflation. occur, possibly resulting in serious personal in-
For inflation pressures and maximum loads, see jury or death.
the tire manufacturer’s guidelines. Inflate the tires 4.2 Inspect for broken, cracked, badly worn,
to the applicable pressures if needed.
bent, rusty, or sprung rings and rims.
If a tire has been run flat or under-inflated, check
the wheel and tire for damage before adding air. NOTICE
Keep compressed air reservoirs and lines dry
during tire inflation. Use well-maintained inline Use the recommended torque values and follow
moisture traps and service them regularly. the proper tightening sequence. Insufficient
wheel nut torque can cause wheel shimmy, re-
sulting in wheel damage, stud breakage, and ex-
WARNING treme tire tread wear. Excessive wheel nut torque
Do not operate the vehicle with underinflated or can break studs, damage threads, and crack
overinflated tires. Incorrect inflation can stress discs in the stud hole area.
the tires and make the tires and rims more sus- 4.3 Make sure all wheel nuts are tightened. If
ceptible to damage, possibly leading to rim or tightening is necessary, use the tightening
tire failure and loss of vehicle control, resulting pattern in Fig. 11.4 or Fig. 11.5.
in serious personal injury or death.
5. Inspect the outboard side of all wheel hubs and
the hub oil seal area on the inboard side of each
NOTICE wheel for signs of oil leakage. If any oil is found
on wheel and tire or brake components, remove
A weekly pressure loss of 4 psi (28 kPa) or more the vehicle from service until the leak has been
in a tire may indicate damage. The tire should be fixed.
inspected and, if necessary, repaired or replaced
by a qualified tire service facility. If needed, fill the hubs to the level indicated on
the hub cap. See Group 35 of the Business
IMPORTANT: The load and cold inflation pres- Class M2 Maintenance Manual for recommended
sure must not exceed the rim or wheel manu- lubricants.
facturer’s recommendations, even though the
6. Check that mud flaps are undamaged and hang
tire may be approved for a higher load inflation.
10 inches (25.4 cm) or less from the ground.
11.5
Truck-Manuals.net
1. Drain the brake system air reservoirs (reservoirs

1 without automatic drain valves only).
10 8
WARNING
3 6 Never operate the engine with the fuel tank shut-
off valves partially closed. This could damage the
fuel pump, causing sudden loss of engine power,
5 4 possibly resulting in serious personal injury due
to reduced vehicle control.
2. Ensure fuel tanks are secured to their mounting
7 9
brackets and that the mounting brackets are se-
2 cured to the frame.
08/23/93 f400081a
If equipped with fuel tank shutoff valves, be sure
Fig. 11.4, Tightening Pattern, 10-Hole Wheels the valves are fully open.
3. Inspect visible frame rails for missing bolts, shiny
1 2 areas, or rust streaks. Check all visible cross-
members for damage or signs of looseness.
4. Inspect visible components of the exhaust sys-
7 4
tem to ensure connections are tight.
Inspect upstream of the aftertreatment device
(ATD) for cracking or signs of leaks, such as soot
trails. Inspect downstream of the ATD for signs of
exhaust leaks, such as blistering or warping of
5 6
nearby components.
Engine Compartment Inspection

3 8
03/08/2012 f400052a
1. Check the ground underneath the engine for fuel,
oil, or coolant leaks.
Fig. 11.5, Tightening Pattern, 8-Hole Wheels 2. Inspect the air intake system for leaks or dam-
age.
Saddle Tank Area Inspections
NOTICE
WARNING
Failure to maintain a sealed air intake system
When draining the air reservoir, do not look into could allow the entry of dirt and contaminants
the air jets or direct them toward anyone. Dirt or into the engine. This could adversely affect en-
sludge particles may be in the airstream and gine performance and result in engine damage.
could cause injury.
2.1 Push the reset button on the air intake
restriction indicator located on the air
NOTICE cleaner, if equipped.
If the water drained from the air reservoirs is 2.2 Check the air intake duct from the air
cloudy or oily, it may indicate a problem with the cleaner to the engine intake. Make sure
compressor. If oil is allowed to contaminate the the duct components are secure and air-
air dryer, it will not remove the water from the air tight.
brake system, which could adversely affect brak-
ing.
11.6
Truck-Manuals.net
2.3 Check the vacuator (spitter) valve(s) for

damage, and make sure the lips of the
valve are pliable and free of debris.
3. Check the engine oil level.
1
NOTICE
Operating the engine with the oil level below the
minimum fill (or "add") mark or above the maxi-
mum fill (or "full") mark could result in engine
damage.
05/21/2007 f462079
3.1 Check the oil level with the vehicle parked 1. Filler Cap
on a level surface. See the engine manu-
facturer’s guidelines for engine shutdown Fig. 11.6, Power Steering Fluid Reservoir
time requirements prior to checking the oil
level. 5.1 If the coolant is low, fill the surge tank to
the MAX line with a 50/50 mixture of water
IMPORTANT: On engines that comply with and the type of antifreeze currently in-
EPA07 or newer regulations, use CJ-4 en- stalled in your vehicle.
gine oil with less than 1% sulfated ash. Fail- For natural gas vehicles, use only Fleet-
ure to use CJ-4 oil may void the warranty on guard ES Compleat™ EG Premix 50/50
emission aftertreatment components. engine coolant.
3.2 If the oil level is at or below the minimum 5.2 If the surge tank was empty, start the en-
fill (or "add") mark on the dipstick, add gine after refilling and check the level
enough oil to maintain the level between again when the engine is at operating
the minimum and maximum fill marks. See temperature.
the engine operation manual for recom-
mended lubricants. 6. Inspect visible engine wiring for damage or
looseness.
For natural gas vehicles, use only Exxon
Busgard® Geo 15W-40 natural gas engine 7. Inspect visible frame rails for missing bolts, shiny
oil. areas, or rust streaks.
4. Check the power steering reservoir fluid level. Cab Inspection
The power steering fluid level should be between
1. Push the reset button on the dash-mounted air
the MIN COLD mark and the middle mark just
intake restriction indicator, if equipped.
above it. See Fig. 11.6. If needed, fill the reser-
voir with automatic transmission fluid that meets 2. With the ignition switch in the OFF position,
Dexron III or TES-389 specifications. check the air-pressure warning system.
2.1 If not previously drained, drain the air res-
NOTICE ervoirs using moderate brake applications
until pressure in both reservoirs is less
Low coolant could result in engine overheating, than 70 psi (483 kPa).
which could cause engine damage.
2.2 Turn the ignition to the ON position. The
IMPORTANT: The surge tank must be cool to ICU will complete a full gauge sweep and
check the coolant level. bulb check, and the warning buzzer will
5. Check the engine coolant level in the radiator sound. Ensure the BRAKE AIR lamp re-
surge tank. mains illuminated and the warning buzzer
continues to sound after the gauge sweep
is complete.
11.7
Truck-Manuals.net
3. Check air governor cut-in and cut-out pressures. 6. Check the air pressure reserve.
3.1 Start the engine and ensure the BRAKE With the engine still off, make one full brake ap-
AIR lamp goes out and the buzzer si- plication and observe the pressure drop on the
lences when pressure reaches approxi- primary air gauge. If pressure drops more than
mately 70 psi (483 kPa) in both air reser- 25 psi (172 kPa), eliminate any leaks before op-
voirs. erating the vehicle.
The air governor should cut out at ap-
Maximum Allowable Air Leakage
proximately 120 psi (827 kPa). For ve-
hicles with an optional dryer reservoir Pressure Drop:
module (DRM), the cut-out pressure is Description psi (kPa) Per Minute
approximately 130 psi (896 kPa). Released Applied
Truck or Tractor Only 2 (14) 3 (21)
3.2 With the engine idling, apply the brake Truck or Tractor w/Single Trailer 3 (21) 4 (28)
pedal several times. The air governor
should cut in when pressure in the primary Table 11.1, Maximum Allowable Air Leakage
air reservoir (top air gauge) reaches ap-
proximately 100 psi (689 kPa).
4. Check air pressure build-up time.
WARNING
4.1 With the air system fully charged, make When cleaning windshields and windows, always
one full brake application and note the air stand on the ground or on a secure ladder or
pressure reading on the primary air platform. Use a long-handled window cleaner. Do
gauge. not use the cab steps, tires, fenders, fuel tanks,
engine, or under-hood components to access the
4.2 Further reduce air pressure using moder- windshield or windows. Doing so could cause a
ate brake applications, then run the en- fall and result in an injury.
gine at governed rpm.
7. Inspect the mirrors, window glass, and wind-
4.3 Note the time that the pressure reaches shield for cracks or other damage.
the previously noted reading on the pri-
mary air gauge, then note the time that 8. Ensure that the horn, windshield wipers, and
the air pressure reaches cut-out pressure. windshield washers are operating properly.
These devices must be in good working order for
4.4 If it takes longer than 30 seconds to reach safe vehicle operation.
cut-out pressure after the primary air
gauge passes the previously noted pres- 9. Ensure the heater and defroster are operating
sure (noted after one full brake applica- properly.
tion), eliminate any leaks or replace the air 10. Check the operation of all interior lights.
compressor before operating the vehicle.
10.1 Turn on the headlights and leave them on.
5. Check air leakage in the system.
Ensure all equipped gauge bulbs illumi-
5.1 With the parking brake applied, the trans- nate in the dash message center.
mission out of gear, and the air system 10.2 Ensure all equipped driver control
fully charged, release the service brakes
switches illuminate.
and shut down the engine.
10.3 Ensure both turn signal indicator bulbs
5.2 Wait one minute and note the air pressure
illuminate in the dash message center
drop in psi (kPa) per minute from the pri-
when the turn signal switch is activated.
mary air reservoir.
11. Check the operation of all exterior lights. See
If the pressure drop exceeds the limits
shown in Table 11.1, eliminate any leaks Fig. 11.7.
before operating the vehicle. 11.1 Activate the high-beam headlights and
hazard warning lights.
11.8
Truck-Manuals.net
making any modifications to the system, may re-

1 sult in personal injury or death.
3 2 12.1 Check the web for fraying, cuts, extreme
2
dirt and dust, or for severe fading from
exposure to sunlight, especially near the
buckle latch plate and in the D-loop guide
area.
12.2 Check operation of the buckle, latch, Kom-
fort Latch or Sliding Komfort Latch (if
equipped), web retractor, and upper seat
4 belt mount on the door pillar. Check all
visible components for wear or damage.
12.3 Check the seat belt and tether belt con-
nection points and tighten any that are
loose.
5 WARNING
8 7 6
Never fill fuel tanks to more than 95 percent of
10/31/2001 8 f543920 their liquid capacity. This could make them more
NOTE: The parking lights, front clearance lights, and likely to rupture from impact, possibly causing
taillights all function as turn signals. fire and resulting in serious personal injury or
death by burning.
1. Utility Light 5. Headlight Low Beam
2. Identification Light 6. Headlight High Beam Do not mix gasoline or alcohol with diesel fuel.
3. Marker Lights 7. Parking Light This mixture could cause an explosion, possibly
4. Front Clearance Light 8. Road Light resulting in serious personal injury or death. Do
Fig. 11.7, Exterior Lights not fill the fuel tanks in the presence of sparks,
open flames, or intense heat. These could ignite
11.2 Exit the cab and check that all exterior the fuel, possibly causing severe burns.
lights and reflectors are clean and intact. IMPORTANT: On engines that comply with
11.3 Check that the brake lights, taillights, EPA07 or newer regulations, use ultralow-sulfur
headlights, turn signals, marker lights, diesel (ULSD) with 15 ppm sulfur content or
identification lights, and clearance lights less. Failure to use ULSD fuel may void the
are working properly. warranty on emission components.
12. Inspect the seat belts and tether belts. 13. Check the fuel level in the fuel tank(s). To keep
condensation to a minimum, fuel tanks should be
WARNING filled at the end of each day.
14. Adjust the rearview and down view mirrors as
Inspect and maintain seat belts. When any part of
a seat belt system needs replacement, the entire necessary.
seat belt must be replaced, both retractor and 15. Test the service brakes.
buckle side. Any time a vehicle is involved in an
accident, and the seat belt system was in use, 15.1 With the engine running and air system
the entire vehicle seat belt system must be re- fully charged, set the parking brake.
placed before operating the vehicle. Do not at- 15.2 Put the vehicle in the lowest gear and
tempt to modify the seat belt system; doing so gently attempt to move it forward. The ve-
could change the effectiveness of the system. hicle should not move.
Failure to replace worn or damaged seat belts, or
11.9
Truck-Manuals.net
If the vehicle moves, the parking brakes

are not operating correctly and must be 8 9
7
repaired before the vehicle is operated. 6 10
Natural Gas Fuel System Inspection, 5
11
If Equipped
1. Inspect fuel tanks for dents, scratches, gouges, 12
or other signs of damage. Inspect the fuel lines
and connections for leaks.
Check that the fuel tanks are securely mounted.
Look for signs of abrasion between components. 4
Compressed Natural Gas (CNG) Fuel System:

3
Ensure that the CNG fuel cylinder storage box is
secured to the frame. Inspect for signs of loose-
2
ness.
Liquefied Natural Gas (LNG) Fuel System: En- 1
sure that the LNG fuel tank is secured to the
mounting brackets and that the mounting
05/05/2010 f470533
brackets are secured to the frame. Ensure all
rubber isolator straps are secure around the LNG 1. Pressure Control Regulator
fuel tank. 2. Vapor Shutoff Valve
3. Fuel Fill Hose
2. Check for the presence of all required decals 4. Secondary Relief Valve (red cap)
present in the following locations: 5. Fuel Fill Fitting
6. Fuel Level Sender Box
• Gas detection system overhead console; 7. Primary Relief Valve
8. Tank Pressure Gauge
• Above the door handle on both doors; 9. Fill Vent Fitting
• Left front bumper; 10. Excess Flow Valve
11. Fuel Shutoff Valve (liquid)
• End-of-frame crossmember; 12. Fill Check Valve
• LNG fuel tank fill port (maximum psi), if Fig. 11.8, LNG Tank Plumbing Components
equipped.
flow valves, if equipped, for signs of damage or
3. Check for the presence of vent caps on pressure leaks. See Fig. 11.8 or Fig. 11.9.
relief valves and devices. If any caps are miss-
ing, have the fuel system inspected by a quali- Inspect the fuel fill fitting for signs of damage or
fied technician. leaks.
CNG Fuel System: Each fuel cylinder should Inspect all lines for signs of leaks or damage,
have two caps (one on each end), which are vis- and check all threaded connections.
ible on the back of the CNG fuel cylinder storage 5. Inspect all fuel gauge components for signs of
box. One additional cap is located on the pres- leaks or damage. Inspect the fuel level sender
sure relief valve on the inboard side of the CNG cable and wiring.
fuel box, next to the fuel outlet line.
6. Inspect all coolant hoses for signs of chafing,
LNG Fuel System: A red cap should be present kinks, or leaks. The LNG fuel system utilizes
on the secondary relief valve (Fig. 11.8). coolant hoses between the engine and the va-
4. Inspect all plumbing components, including the porizer; the CNG fuel system utilizes coolant
fuel shutoff valve(s), primary and secondary relief hoses between the engine and the pressure
valves, and the LNG vapor shutoff and excess regulator inside the fuel panel.
11.10
Truck-Manuals.net
2. After resetting the air intake restriction indicator

1 2 during the daily pretrip inspection, check the indi-
cator again with the engine off.
2.1 Check an indicator with graduations to see
if air restriction exceeds the value shown
in Table 11.2.
H IG CYLINDERS RE
H PRESS UR E LOW PRES S U
INSPECT CYLINDERS
REGULATOR
EVERY 36 MONTHS
OR 36000 MILES
WHICHEVER OCCURS FIRST Check a go/no-go indicator without gradu-
INSPECT PRESSURE
RELIEF DEVICE
EVERY 2000 MILES
NATURAL
GAS
VEHICLE
ations to see if the colored bar shows
110 PSIG
FILTER ON
OPEN VALVE
SLOWLY
through the clear window.
3600 PSIG MAX.
SERVICE PRESSURE
DRAIN HOUSING
EVERY 1500 MILES
REPLACE ELEMENT 4
VA T O AL
LV FF
EVERY 3000 MILES

U U
E
SH AN
3
M
Air Intake Maximum Restriction Values (inH2O)

Pre-EPA07 EPA07 and
Engine
Caterpillar 25 —
Cummins 25 25
04/30/2010 f470556
Detroit Diesel 20 22
1. High Pressure Gauge Mercedes-Benz 22 22
2. Low Pressure Gauge
3. Manual Fuel Shutoff Valve Table 11.2, Air Cleaner Element Maximum Restriction
4. Fuel Fill Port
Fig. 11.9, CNG Fuel Panel 2.2 If air restriction exceeds the maximum al-
lowable value, operate the vehicle for one
7. If equipped with an LNG fuel system, check the more day, making sure not to run the en-
fuel tank pressure gauge to ensure that pressure gine over rated rpm. Refer to the engine
is within the normal range of 120 to 150 psi (827 operation manual for more information on
to 1034 kPa). If tank pressure exceeds 230 psi rated rpm for your engine.
(1586 kPa) and the pressure relief valve does
2.3 If air restriction exceeds the maximum
not open automatically, vent the tank immedi-
ately. value again, replace the air cleaner. For
instructions, refer to Group 09 of the
8. Inspect the LNG vaporizer for signs of damage Business Class M2 Workshop Manual.
or leaks. See Fig. 11.10. Inspect the vaporizer
3. If the vehicle is equipped with an Allison auto-
mounting brackets for signs of looseness.
matic transmission, check the automatic trans-
mission fluid level.
Weekly Post-Trip Inspection
4. Check for water in the fuel/water separator, if
and Maintenance equipped.
Engine Compartment Inspection IMPORTANT: When draining fluid from a
fuel/water separator, drain the fluid into an
WARNING appropriate container and dispose of it prop-
erly. Many jurisdictions now issue fines for
Washer fluids may be flammable and poisonous. draining fuel/water separators onto the
Do not expose washer fluid to an open flame or ground.
any burning material, such as a cigarette. Always
comply with the washer fluid manufacturer’s rec- 4.1 Place a suitable container under the fuel/
ommended safety precautions. water separator.
1. Check the windshield washer reservoir fluid level. NOTE: A hose may be used to direct water
The reservoir is usually located near the right- into the container. Use a hose with a ½-inch
hand frame rail. pipe thread on DAVCO models.
11.11
Truck-Manuals.net
9
8
1
12
11
10
4 6
2 3
06/29/2009 f470536
1. Pressure Relief Device 5. Coolant Inlet Line 9. Pressure Gauge

2. Fuel Inlet Line 6. Vaporizer 10. Overpressure Regulator
3. Check Valve 7. Fuel Shutoff Solenoid Valve 11. Pressure Relief Valve
4. CNG Quick-Connect Port 8. Coolant Outlet Line 12. Fuel Outlet Line
Fig. 11.10, LNG Vaporizer Assembly
4.2 If the engine is equipped with a built-in 5. Inspect the steering components. See Fig. 11.13.
water separator, loosen the drain valve,
and allow the water to run out. Close the
5.1 Inspect tie rods, steering arms, and the
drain valve, taking care not to overtighten
it. drag link for signs of looseness (i.e., shiny
spots or rust tracks).
4.3 Alliance/Racor Models: Turn the drain plug
5.2 Check the steering gear mounting bolts
counterclockwise to open it. See
Fig. 11.11. and pitman arm nut for signs of loose-
ness.
DAVCO Models: Remove the vent cap
and open the drain. See Fig. 11.12. 5.3 Check the drag link nuts for missing cotter
pins.
4.4 Stop draining fluid when fuel begins to
drain out. 5.4 Inspect the steering intermediate shaft and
end yokes for excessive looseness or
Alliance/Racor Models: turn the drain plug other damage.
clockwise to close it.
DAVCO Models: close the drain valve.
Install and hand-tighten the vent cap.
11.12
Truck-Manuals.net
6
5
10
4
3
7
9
2
8
8
1 7
9
10
6
11 5
02/03/2010 f470552
1. Washers (qty 2) 7. Mounting Head
2. Nuts (qty 2) 8. Mounting Bolts (qty 2)
3. Frame Rail 9. Filter Element
4. Fuel Outlet Port 10. Sight Bowl 4
5. Fuel Inlet Port 11. Drain Plug
6. Priming Pump
11
Fig. 11.11, Alliance Fuel/Water Separator Assembly and
Installation 3
12
NOTICE 2
Do not drive with a drive belt that is visibly worn
or damaged. If it fails, the lack of coolant flow
could rapidly cause damage to engine compo-
nents.
6. Inspect the serpentine drive belts for signs of
glazing, frayed edges, breaks, cracks, or oil con- 1 13
tamination.
05/05/2009 f470530
Monthly Post-Trip Inspection 1.

2.
Inlet Port/Check Valve
Lower Housing
8.
9.
Vent Cap O-Ring
Vent Cap
and Maintenance 3. Bypass Valve 10. Collar
4. Filter Element 11. 120VAC Pre-Heater
Brake Component Inspection 5. Spring 12. 12VDC Pre-Heater
6. Cover O-Ring 13. Drain Valve
Walk around the vehicle and visually the brake sys- 7. Clear Cover
tem components for visible damage.
Fig. 11.12, DAVCO Fuel/Water Separator (Fuel Pro 482
shown)
11.13
Truck-Manuals.net
6. Check the thickness of the brake linings. Re-

place brake linings on all brake assemblies on
the axle if any brake linings are worn to less than
approximately 1/4 inch (6.4 mm) at the thinnest
point.
1 Saddle Tank Area Inspections
1 WARNING
When draining the air reservoir, do not look into
the air jets or direct them toward anyone. Dirt or
2 1 sludge particles may be in the airstream and
could cause injury.
3
3 NOTICE
If the water drained from the air reservoirs is
10/11/2001 f461916 cloudy or oily, it may indicate a problem with the
1. Steering Gear Mounting Bolt compressor. If oil is allowed to contaminate the
2. Pitman Arm Pinch Bolt Nut air dryer, it will not remove the water from the air
3. Drag Link Nut brake system, which could adversely affect brak-
ing.
Fig. 11.13, Steering Gear Fasteners
1. Drain the brake system air reservoirs (reservoirs
1. Inspect all visible brake system components for with automatic drain valves only).
missing fasteners or signs of looseness, such as
rust tracks. NOTE: Battery locations vary between vehicles.
2. Inspect the batteries.
NOTICE
WARNING
If the external breather tube or breather cap is
missing or incorrectly installed, road dirt and de- Battery posts, terminals, and related accessories
bris can adversely affect the operation of the contain lead and lead compounds, chemicals
brake chamber. Once inside of the chamber, dirt known to the State of California to cause cancer
and debris can cause the internal parts of the and reproductive harm. To prevent possible per-
chamber to deteriorate faster. sonal injury, always wash your hands after han-
2. Inspect the exterior surfaces of brake chambers dling battery parts and related accessories.
for damage. Make sure that breather holes are 2.1 Remove the battery box cover and inspect
open and free of debris. all visible battery cables for loose wiring or
damage.
NOTE: Do not route air brake lines on top of
anything likely to be stepped on. 2.2 Check that the battery hold-down is se-
cure.
3. Inspect air brake lines for dents, swelling, kinks,
twisting, abrasion, and damage, especially near IMPORTANT: Aerodynamic components de-
moving parts. crease drag force as a vehicle moves, thereby
4. Inspect flex air lines for deterioration or signs of improving fuel efficiency. If replacement of an
abrasion. aerodynamic component is necessary, replace-
ment components must meet or exceed the
5. Inspect for cracked, worn, or oil-contaminated
brake linings and brake drums (or rotors).
11.14
Truck-Manuals.net
drag reduction performance of the originally in- IMPORTANT: Do not overtighten hose
stalled component in order to maintain compli- clamps, as hose life can be adversely af-
ance with greenhouse gas and full efficiency fected.
regulations (GHG14). 3.5 Ensure hose support brackets are se-
3. Inspect the following aerodynamic components, if curely fastened. Make sure hoses are not
equipped, for structural damage, cracks, or wear. located near sources of wear, abrasion, or
high heat.
• Chassis fairings
IMPORTANT: When replacing hoses, install
• Roof fairing/deflector
service-type knitted or braided yarn-reinforced
• Side skirts neoprene hose. Extended-service-life silicone
• Cab extenders hoses may also be used. See the Alliance Parts
Catalog at www.alliancebrandparts.com or
• Battery access cover contact your Freightliner Dealer.
Engine Compartment Inspection and 4. Check the steering wheel for excessive play.
Adjustments 4.1 Start the engine. With the front tires
straight ahead, turn the steering wheel
IMPORTANT: If replacement of the hood or until motion is observed at the front
bumper is necessary, the replacement compo- wheels.
nent must meet or exceed the drag reduction
4.2 Align a reference mark on the steering
performance of the originally installed item in
wheel to a rule, then slowly turn the steer-
order to maintain compliance with greenhouse ing wheel in the opposite direction until
gas and full efficiency regulations (GHG14). motion is again detected at the wheels.
1. Inspect the bumper and hood for structural dam- 4.3 Measure the lash (free play) at the rim of
age, cracks, or wear. the steering wheel. Excessive lash exists
2. Check the hydraulic clutch reservoir, if equipped. if steering wheel movement exceeds 2-1/2
If necessary, add DOT 4 brake fluid. inches (64 mm) with a 20-inch (508-mm)
steering wheel, or 2-1/4 inches (57 mm)
3. Inspect the radiator and heater hoses, including with an 18-inch (450-mm) steering wheel.
the clamps and support brackets.
4.4 If there is excessive lash, check the steer-
3.1 Inspect the radiator and charge air cooler ing system for wear or incorrect adjust-
for damage and accumulated debris. ment before operating the vehicle.
Straighten bent or damaged fins to permit
airflow across all areas of the cores. Natural Gas Fuel System Inspection,
NOTE: When traveling through areas of high If Equipped
insect concentration, it may be necessary to
1. Leak test all fuel system components, joints, and
clean the exterior of the radiator or the
fittings using a methane detector. A bubble solu-
charge air cooler core as often as every 200 tion can be used to pinpoint the exact location of
miles (320 km). leaks.
3.2 Make sure the radiator inlet and outlet Replace any leaking or damaged fuel tanks and
hoses are pliable and are not cracking or fuel lines; repair or replace leaking or damaged
ballooning. fittings.
3.3 Make sure the heater hoses are pliable 2. Drain the CNG high-pressure fuel filter housing,
and are not cracking or ballooning. if equipped.
3.4 Tighten hose clamps as necessary.
11.15
Truck-Manuals.net
2.1 Purge the CNG fuel lines by closing the 2.4 Slowly open the bleed valve on the mani-
CNG fuel cylinder shutoff valves. Start the fold to relieve remaining fuel pressure
engine and let it idle until the fuel lines are within the system. See Fig. 11.15.
empty and the engine stops.
6
Gauges on the fuel panel should now read
5
at or near 0 psi (0 kPa).
7
2.2 Close the manual fuel shutoff valve on the
fuel panel.
2.3 Remove the two capscrews that secure
the access cover to the fuel panel, then 4 8
remove the access cover. See Fig. 11.14.
Save the capscrews for installation.
2 10 9
13 12 11
8 14
1
05/04/2010 f470558
1. Coolant Inlet Port 9. Fuel Fill Port
7 2. Coolant Outlet Port 10. High-Pressure Filter
3. Pressure Relief Valve 11. Filter Bowl
4. Pressure Regulator 12. Filter Drain Plug
2 5. Wiring Harness 13. Solenoid Valve
6. Manifold Bleed Valve 14. Fuel Line To Cylinders
6
7. Manifold
5
4 8. Manual Fuel Shutoff
3 2 Valve
Fig. 11.15, CNG Fuel Panel Components
IMPORTANT: Some pressure may remain in

the fuel system between the solenoid valve
and the engine. Use caution when loosening
fittings, as a small amount of gas may leak
1 out.
05/04/2010 f470557 2.5 Put a clean receptacle under the filter as-
sembly.
1. Fuel Panel Access Cover
2. Capscrews (qty 2) 2.6 Using an 11/16-inch wrench, remove the
3. Wiring Harness drain plug from the filter bowl.
4. Pressure Relief Valve and Cap
5. Coolant Outlet Line When all liquid has drained, install and
6. Coolant Inlet Line tighten the drain plug on the filter bowl.
7. Fuel Inlet Line (to fuel cylinders)
8. Fuel Outlet Line (to engine) 2.7 Close the bleed valve on the manifold and
open the manual fuel shutoff valve on the
Fig. 11.14, CNG Fuel Panel Assembly fuel panel.
Open the fuel cylinder shutoff valves.
11.16
Truck-Manuals.net
2.8 Use a methane detector to leak test all

fuel system components between the fuel
cylinders and the solenoid valve. A bubble
solution can be used to pinpoint the exact
location of leaks.
Repair or replace any leaking compo-
nents.
2.9 Install the access cover on the fuel panel.
11.17
Truck-Manuals.net
12
Cab Appearance
Cab Washing and Polishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1
Care of Fiberglass Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1
Care of Chrome Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1
Care of Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1
Dashboard Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1
Vinyl Upholstery Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Velour Upholstery Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3
Truck-Manuals.net
Cab Appearance
Cab Washing and Polishing Care of Fiberglass Parts

Wash unpainted fiberglass air fairings and shields
CAUTION monthly with a mild detergent, such as dishwashing
liquid. Avoid strong alkaline cleansers.
When pressure washing the vehicle or leaving
the hood open when parked outdoors and sub- Apply a wax specifically designed for fiberglass.
ject to rain, cover the air cleaner inlet with a plas-
tic bag to prevent water from entering the air in- Care of Chrome Parts
take system and possibly damaging the engine.
To prevent rust, keep chrome parts clean and pro-
To protect the finish of your new vehicle, follow these tected at all times. This is especially important during
guidelines carefully: winter driving and in coastal areas where there is
• During the first 30 days, rinse your vehicle fre- exposure to salt air.
quently with water. If the vehicle is dirty, use a When cleaning chrome parts, use clean water and a
mild liquid soap. Do not use detergent. soft cloth or sponge. A mild detergent may also be
• During the first 30 days, do not use anything used.
abrasive on your vehicle. Brushes, chemicals, Sponge gently, then rinse. If necessary, use a non-
and cleaners may scratch the finish. abrasive chrome cleaner to remove stubborn rust or
• During the first 120 days, do not wax your other material. Do not use steel wool.
vehicle. To help protect the chrome after cleaning, apply a
To extend the life of your vehicle’s finish, follow these coat of polishing wax to the surface. Never use wax
guidelines: on parts that are exposed to high heat, such as ex-
haust pipes.
• Avoid washing your vehicle in the hot sun. Al-
ways use water. After the cab is completely
washed, dry it with a towel or chamois. Care of Exterior Lights
• Do not dust painted surfaces with a dry cloth, Clean the headlight lenses by hand only, using a
as this will scratch the paint. flannel cloth with mild, non-caustic soap or detergent,
and water.
• Do not remove ice or snow from a painted sur-
face with a scraper of any sort.
CAUTION
• To prevent damage to the finish, wax it regu-
larly. If the finish has become dull, before wax- Do not use a power buffer, paper towels, chemi-
ing, remove oxidized paint using a cleaner spe- cal solvents, or abrasive cleaners on the head-
cifically designed for this purpose. Remove all light lens, all of which can remove the UV coating
road tar and tree sap before waxing. Freight- from the surface, and result in yellowing of the
liner recommends that a quality brand of lens.
cleaner or cleaner-polish and polishing wax be
used. Dashboard Care
• Do not let diesel fuel or antifreeze stand on a
painted surface. If either should occur, rinse NOTICE
the surface off with water.
• To prevent corrosion, have any nicks or other When cleaning the dashboard, instrument panel,
damage on the finish touched up as soon as or gauge lens covers, do not use Armor-All Pro-
possible. tectant®, STP Son-of-a-Gun®, window cleaner, or
other equivalent treatments. These cleaners con-
• Park your vehicle in a sheltered area whenever tain vinyl plasticizers which can cause stress
possible. crazing in the interior plastic panels and can re-
sult in cracking of the panels. Some cleaners can
12.1
Truck-Manuals.net
Cab Appearance
also have an adverse effect on the clear plastic ately and the area carefully cleaned, using a cloth
of instrument panels and gauge lens covers, re- dampened with naphtha.
sulting in a foggy or cloudy appearance. This
type of damage is not covered by vehicle war- Paint, Shoe Heel Marks
ranty.
Paint should be removed immediately. Do not use
To clean the dashboard, instrument panel, and gauge paint remover or liquid-type brush cleaner on vinyl.
lens covers, use a cloth dampened with warm soapy An unprinted cloth, dampened with naphtha or tur-
water. Make certain to wring the cloth out well before pentine may be used. Use care to prevent contact
cleaning, as excess water will damage the electrical with parts of the upholstery that are not vinyl.
components.
Sulfide Stains
Vinyl Upholstery Cleaning Sulfide compounds, such as those found in eggs and
To prevent soiling, frequent vacuuming or light brush- some canned goods, can stain after prolonged con-
ing to remove dust and dirt is recommended. Harsh tact with vinyl. These stains can be removed by plac-
cleaning agents can cause permanent damage to ing a clean, unprinted piece of cloth over the spotted
vinyl upholstery. To preserve the upholstery and pre- area and pouring a liberal amount of 6 percent hy-
vent damage, carefully review the following sections drogen peroxide onto the cloth. Allow the saturated
for recommended cleaning procedures. Waxing or cloth to remain on the spot for 30 to 60 minutes. For
refinishing improves soil resistance and cleanability stubborn spots, allow the hydrogen-peroxide satu-
for all vinyls. Any hard wax, such as that used on rated cloth to remain on the area overnight. Use cau-
automobiles, may be used. tion to prevent the solution from seeping into the
seams or it will weaken the cotton thread.
Ordinary Dirt
Nail Polish and Nail Polish Remover
Wash the upholstery with warm water and mild soap,
such as saddle or oil soap. Apply soapy water to a Prolonged contact with these substances causes per-
large area and allow to soak for a few minutes, then manent damage to vinyl. Careful blotting immediately
rub briskly with a cloth to remove the dirt. This can after contact minimizes damage. Do not spread the
be repeated several times as necessary. liquid during removal.
If dirt is deeply imbedded, use a soft bristle brush Shoe Polish
after applying the soap.
If dirt is extremely difficult to remove, wall-washing Most shoe polishes contain dyes which penetrate
preparations normally found around the home can be vinyl and stain it permanently. Shoe polish should be
used. Powdered cleaners, such as those used for wiped off as quickly as possible using naphtha or
sinks and tiles, are abrasive and must be used with lighter fluid. If staining occurs, try the procedure used
caution as they can scratch the vinyl or give it a per- for sulfide stains.
manent dull appearance.
Ball Point Ink
Chewing Gum Ball point ink can sometimes be removed if rubbed
Harden the gum with an ice cube wrapped in a plas- immediately with a damp cloth, using water or rub-
tic bag, then scrape it off with a dull knife. Any re- bing alcohol. If this does not work, try the procedure
maining traces of gum can be removed with an all- used for sulfide stains.
purpose light oil (peanut butter will also work) and
wiped off. Miscellaneous
If stains do not respond to any of the treatments de-
Tars, Asphalts, and Creosote scribed above, it is sometimes helpful to expose the
Tars, asphalts, and creosote stain vinyl after pro- vinyl to direct sunlight for up to 30 hours. Mustard,
longed contact. They should be wiped off immedi- ball point ink, certain shoe polishes, and dyes often
12.2
Truck-Manuals.net
Cab Appearance
bleach out in direct sunlight leaving the vinyl undam-

aged.
Velour Upholstery Cleaning

To prevent soiling, frequent vacuuming or light brush-
ing to remove dust and dirt is recommended. Spot
clean with a mild solvent or an upholstery shampoo,
or the foam from a mild detergent. When using a sol-
vent or a dry-cleaning product, follow the instructions
carefully and clean only in a well-ventilated area.
Avoid any product that contains carbon tetrachloride
or other toxic materials. With either method, pretest a
small area before proceeding. Use a professional
upholstery cleaning service when extensive cleaning
is needed.
Grease and Oil-Based Stains

Dampen a small absorbent cloth with dry-cleaning
solvent or spot remover. Apply the cloth carefully to
the spot from the outer edge to the center. Pat and
blot the spot with a clean, dry cloth. Repeat several
times, as necessary, turning the cloths so that the
stain does not redeposit on the fabric.
Sugar and Water-Based Stains

Apply water-based detergent or cleaner, working in
circular motions. Pat and blot as dry as possible. Re-
peat if necessary before drying thoroughly.
Chewing Gum or Wax

Harden the gum or wax with an ice cube wrapped in
a plastic bag, then scrape it off with a dull knife. Ex-
cess wax can be absorbed by placing a thick white
blotter over the wax and heating with a warm (not
hot) iron. Remove the remainder by using the proce-
dure for grease and oil-based stains.
Mildew
Brush the dry fabric with a soft brush. Sponge with
detergent, and blot. If the fabric is colorfast, dilute a
teaspoon of bleach in one quart (one liter) of cool
water. Apply with a swab, directly on the mildew
stain. Dab repeatedly with clear, cool water, and blot
dry.
12.3
Truck-Manuals.net
13
In an Emergency
Hazard Warning Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1
Fire Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1
Emergency Kit, Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1
Emergency Filter Replacement, Davco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1
Emergency Starting With Jumper Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5
Fire in the Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7
Truck-Manuals.net
In an Emergency
Hazard Warning Lights WARNING

The hazard warning light flasher (Fig. 13.1) is part of
the multifunction turn signal switch. It is a red rocker Use extreme care when placing flares in emer-
switch located on the top of the multifunction switch gency situations that involve exposure to flam-
module. mable substances such as fuel. An explosion or
fire could occur causing serious personal injury.
4
Emergency Filter
Replacement, Davco
5
If the filter cover on the Davco fuel/water separator is
broken, it will not be possible to operate the vehicle.
1 A standard spin-on filter will correct this problem.
2 Refer to the Davco web site for additional informa-
tion, www.davcotec.com.
3
To replace the filter on all Davco fuel/water separa-
tors, follow these procedures:
11/16/2001 f820386
1. Drain the fuel until it is below the level of the fil-
Press down on the upper part of the rocker to activate ter collar. See Fig. 13.2 for the model 232/233
the flashers. fuel/water separator and Fig. 13.3 for the model
1. Washer Button 382 fuel/water separator.
2. Wiper Control Dial
3. Turn Signal Lever 2. Remove the filter vent and vent seal.
4. Hazard Flasher (red)
5. Multifunction Switch Module NOTE: The filter vent and vent seal are not
needed in the emergency replacement. They
Fig. 13.1, Hazard Warning Flashers should be retained for later installation at the
To flash the hazard warning lights, press down on time when the filter cover is replaced.
the upper part of the rocker (towards the dash). To 3. Remove the filter collar using channel-lock pliers.
stop the hazard warning lights, press down on the
lower part of the rocker (towards the steering wheel). 4. Remove the filter cover, filter cover seal and
spring. Retain them for later assembly.
Fire Extinguisher 5. Remove the filter element and dispose of it prop-
erly.
A fire extinguisher is located in the cab by the
driver’s door. 6. Install the standard engine spin-on filter (included
in the emergency kit) on the threaded stud.
Emergency Kit, Optional NOTE: Remove the rubber grommet from the
stud.
An optional emergency kit is located in the cab. The
kit includes one or more of the following: a first aid 7. Install the filter cover, filter cover seal, and
kit, a reflective vest, a triangular reflector, a flare kit, spring, as removed.
and (on vehicles with a Davco fuel/water separator) a 8. Install the filter collar over the filter cover. Tighten
spin-on fuel filter element.
the filter collar finger-tight.
If there is an emergency while driving, cautiously pull
9. Start the engine and run it at increased rpm for
off the road. Turn on the hazard warning lights. Place
one minute to purge air from the fuel lines.
the flares and reflector along the side of the road to
alert other drivers that an emergency situation exists.
13.1
Truck-Manuals.net
In an Emergency
6
10
11/14/2001 f470416
1. Filter Vent 5. Filter Cover Seal 8. Threaded Stud
2. Filter Vent Seal 6. Spring 9. Fuel Port
3. Filter Collar 7. Filter Element 10. Drain
4. Filter Cover
Fig. 13.2, Davco Model 232 and 233 Fuel/Water Separator
Emergency Starting With in the vicinity of the battery. Do not allow the ve-
hicles to touch each other. Do not lean over the
Jumper Cables batteries when making connections, and keep all
other persons away from the batteries. Failure to
When using jumper cables, follow the instructions follow these precautions could lead to severe
below. personal injury as a result of an explosion or
acid burns.
WARNING
Batteries release explosive gas. Do not smoke
when working around batteries. Put out all flames
and remove all sources of sparks or intense heat
13.2
Truck-Manuals.net
In an Emergency
3
8
9
6
10
11
11/14/2001 f470417
1. Filter Collar 5. Filter Cover Seal 9. Fuel Port
2. Filter Vent 6. Spring 10. Drain
3. Filter Vent Seal 7. Filter Element 11. Bottom Plate Collar
4. Filter Cover 8. Threaded Stud
Fig. 13.3, Davco Model 382 Fuel/Water Separator
1. Apply the parking brakes and turn off the lights

NOTICE and all other electrical devices.
Make sure both starting systems have the same 2. To gain access to the batteries, open the battery
voltage outputs, and avoid making sparks. Other- compartment. See Fig. 13.4. For detailed instruc-
wise the vehicle charging systems could be se- tions, see Chapter 2.
verely damaged. Also, do not attempt to charge
isolated, deep-cycle batteries with jumper cables. NOTICE
Follow the battery manufacturer’s instructions
when charging deep-cycle batteries. Always connect the battery, jumper cables, and
charger correctly (positive-to-positive and
NOTE: On vehicles equipped with an optional
negative-to-negative). Connecting a charging de-
jump-start post, attach the positive cable clamp vice backwards (positive-to-negative) will blow
to that post instead of to the battery. fuses that power the bulkhead module (BHM) and
13.3
Truck-Manuals.net
In an Emergency
chassis module (CHM), and the devices they con-

trol will not work. WARNING
3. Connect an end of one jumper cable to the posi- Do the next step exactly as instructed and do not
tive terminal of the booster battery (or jump-start allow the clamps of one cable to touch the
post if equipped), and connect the other end of clamps of the other cable. Otherwise, a spark
the cable to the positive terminal of the dis- could occur near a battery, possibly resulting in
charged battery (or jump-start post if equipped). severe personal injury from explosion or acid
See Fig. 13.5. burns.
4. Connect one end of the second jumper cable to
3
the negative terminal of the booster battery, and
connect the other end of the cable to a ground at
least 12 inches (300 mm) away from the batter-
ies of the vehicle needing the start. The vehicle
2 frame is usually a good ground. Do not connect
the cable to or near the discharged batteries.
WARNING
On vehicles with Mercedes-Benz AGS transmis-
sions, make sure the current gear indicator dis-
4 plays "N" before starting the vehicle. If the trans-
1 mision starts in gear, it could cause an accident
10/24/2001 f543933 resulting in death, serious personal injury, or
1. Top Step 3. Cab property damage.
2. Battery 4. Battery Access Door 5. Start the engine of the vehicle with the booster
Fig. 13.4, Battery Compartment, Open batteries, and let the engine run a few minutes to
charge the batteries of the other vehicle.
C 6. Attempt to start the engine of the vehicle with the
A batteries receiving the charge. Do not operate
B D the starter longer than 30 seconds, and wait at
least two minutes between starting attempts to
+ − + allow the starter to cool.
− E
E G 7. When the engine starts, let it idle a few minutes.
+ − +
− F WARNING
A
1 2
10/18/94 f540303a
Do the next step exactly as instructed and do not
allow the clamps of one cable to touch the
A. To Ground E. To Starter clamps of the other cable. Otherwise, a spark
B. 3rd F. 2nd
could occur near a battery, possibly resulting in
C. To Frame (ground) G. 1st
D. 4th severe personal injury from explosion or acid
burns.
1. Booster Battery
2. Discharged Battery 8. Disconnect the grounded cable from the frame or
other non-battery location, then disconnect the
Fig. 13.5, Jumper Connections
other end of the cable.
9. Disconnect the remaining cable from the newly
charged battery (or jump-start post if equipped)
first, then disconnect the other end.
13.4
Truck-Manuals.net
In an Emergency
10. Close the battery compartment. For detailed in- to the vehicle frame. Use protection to keep the
structions, see Chapter 2. chains from damaging the frame.
5. Remove the bumper end caps and chrome bum-
Towing per (if equipped).
When it is necessary to tow the vehicle, make sure
the instructions below are closely followed to prevent NOTICE
damage to the vehicle.
Do not pass a sling (for example, a rope or chain)
from one tow hook to another to fasten for tow-
WARNING ing (see Fig. 13.6). Known as reeving, this prac-
tice is not permissible in most industrial applica-
Do not tow an unbraked vehicle if the combined
tions of towing and hoisting. Reeving can
weight of both vehicles is more than the sum of
overload the hooks and result in damage to the
the gross axle weight ratings (GAWR) of the tow-
vehicle.
ing vehicle. Otherwise brake capacity will be in-
adequate, which could result in personal injury or 6. Attach the towing device. Due to the many vari-
death. ables that exist in towing, positioning the lifting
and towing device is the sole responsibility of the
Front Towing Hookup towing-vehicle operator.
1. Disconnect the battery ground cables. 7. Lift the vehicle and secure the safety chains. If
extra towing clearance is needed, remove the
front wheels.
NOTICE
8. Connect the clearance lights, taillights, and sig-
Failure to remove the axle shafts when towing nal lights. Connect any special towing lights re-
the vehicle with the rear wheels on the ground quired by local regulations.
could result in damage to the transmission and
other parts. WARNING
2. Remove both drive axle shafts. On dual drive
axles, if the vehicle is to be lifted and towed, re- Failure to chock the tires or connect the tow
move only the rearmost drive axle shafts. truck’s air brake system before releasing the
spring parking brakes could allow the disabled
On vehicles equipped with an air fairing, remove vehicle to suddenly roll. This could cause prop-
both the forward and rearmost drive axle shafts if erty damage or personal injury.
there is insufficient towing clearance.
9. Chock the tires on the disabled vehicle and con-
3. Cover the ends of the hubs with metal plates or nect the towing vehicle’s air brake system to the
plywood cut to fit the axle opening, and drilled to vehicle being towed. Then, release the spring
fit the axle shaft studs. This prevents lubricant parking brakes and remove the chocks.
from leaking out and will keep contaminants from
getting into and damaging the wheel bearings Rear Towing Hookup
and axle lubricant.
NOTICE NOTICE
Using a rear towing hookup on a vehicle
Failure to protect the frame rails from the chains
could cause damage, leading to eventual frame equipped with a roof fairing could cause damage
failure. to the cab structure.
4. On dual drive axles, if the vehicle is to be lifted If reverse towing at speeds above 45 mph (70
and towed, chain the forward rear-axle assembly kph) is necessary, hold down the cab with ten-
sion straps looped over the cab shocks and
under the frame rails. Failure to do so could
13.5
Truck-Manuals.net
In an Emergency
OK
2 1
1
OK
01/11/2006 f880694
IMPORTANT: Do not reeve when towing.

1. Tow Hook 2. Chain
Fig. 13.6, Reeving
allow the wind load to lift the cab unexpectedly,

resulting in damage to the air springs and other NOTICE
components.
Failure to protect the frame rails from the chains
1. If the vehicle is equipped with cab air suspen- could cause damage, leading to eventual frame
sion, and reverse towing at speeds above 45 failure.
mph (70 kph) is necessary, hold down the cab as
follows: 4. On dual drive axles, using protection to keep the
chains from damaging the vehicle frame, chain
1.1 Drain the air from the cab air springs. the forward-rear drive axle to the frame.
1.2 Loop a 2-inch (5-cm) ratchet-style tension 5. Attach the towing device.
strap (rated 2000 lb [900 kg] minimum
work load) over the top of the cab shock NOTE: Due to the many variables that exist in
and under the frame rail. Tighten the strap towing, positioning the lifting and towing device
for a snug fit. If the cab is equipped with is the sole responsibility of the towing-vehicle
two or more shocks, restrain the aftmost operator.
shock on each side of the vehicle.
6. Lift the vehicle and secure the safety chains. If
2. Place the front tires straight forward and secure extra clearance is needed, remove the bumper
the steering wheel in this position. extension if equipped.
3. Disconnect the battery ground cables. 7. Connect the clearance lights, taillights, and sig-
nal lights. Also connect any special towing lights
required by local regulations.
13.6
Truck-Manuals.net
In an Emergency
Fire in the Cab

The incidence of fire in medium-duty trucks is rare,
according to data from the National Highway Traffic
Safety Administration. Federal Motor Vehicle Safety
Standard #302 limits the flammability of specified
materials used inside the cab, but despite this, most
materials will burn. The cab of this vehicle contains
urethane foam, which is of concern in this respect.
WARNING
Urethane foam is flammable! Do not allow any
flames, sparks, or other heat sources such as
cigarettes or light bulbs to contact urethane
foam. Urethane foam in contact with such heat
sources could cause a serious, rapid fire, which
could result in death, severe burns, or gas poi-
soning, as well as damage to the vehicle.
In Case of a Cab Fire

As quickly as possible, bring the vehicle to a safe
stop, apply the parking brake, turn off the ignition,
and get out of the vehicle.
13.7
Truck-Manuals.net
14
Headlight Aiming
Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1
Checking Headlight Aim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1
Adjusting Headlight Aim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1
Truck-Manuals.net
Headlight Aiming
3. Mark the vertical distances found in step 2 on

Preliminary Checks the screen or wall, directly in front of the head-
Before checking or adjusting the headlight aim, do lights. These marks represent the desired loca-
the following: tions of each headlight bulb center in the follow-
ing steps. See Fig. 14.2, Items 2 and 3.
• Check that the hood is closed and latched.
4. Turn on the low-beam headlights.
• Check the suspension for proper functioning of
the leveling mechanism. On cabs with air sus- 5. Identify the center of each beam projection by
pensions, make sure that the height is properly marking the area of brightest intensity on the
adjusted. wall. The area of brightest intensity should fall on
or very near the marks made during step 3. See
• Remove any large amounts of mud or ice from Fig. 14.3.
the underside of the fenders.
6. Use Table 14.1 to determine the maximum verti-
• Check the springs for sagging or broken cal distance allowable between the marks made
leaves. in step 3 and the marks made in step 5. If the
• Check for damage to the hood and hinge as- vertical distance between the marks made in
sembly. Repair as necessary. steps 3 and 5 is greater than the maximum dis-
tance given in Table 14.1, adjust the vertical po-
• With the vehicle unloaded, check that the tires sitioning of that headlight.
are inflated to the recommended air pressure.
• Clean the headlight lenses. Use a soft cloth Adjusting Headlight Aim
with mild, non-caustic soap or detergent, and
water. NOTE: Freightliner vehicles are offered with
various headlight assembly options. Because of
the various options, the location of adjustment
Checking Headlight Aim screws on the vehicle’s headlight assembly may
1. Park the vehicle on a level surface, 25 ft (7.6 m) vary from what is shown here.
away from, and perpendicular to, a vertical 1. Lift the flap over the rear end of the headlight
screen or wall. Shut down the engine and set the
bucket to expose the two plastic adjusting knobs
parking brake. Chock the tires.
on each headlight. See Fig. 14.4.
2. Each headlight has a height adjusting dot. See 2. If necessary, adjust the horizontal positioning of
Fig. 14.1. Measure the distance from the ground the headlights so that each projection points di-
to the height adjusting dot on each headlight. rectly forward.
Note those distances. See Fig. 14.2, Ref. A.
3. Turn the vertical adjustment knob to adjust the
headlight beam to meet the desired height. See
Table 14.1. Turn the knob clockwise to raise the
beam; turn the knob counterclockwise to lower it.
4. Adjust the other headlight.
11/06/2002 f544236
Measure beam height from the ground to the small dot

roughly in the center of the headlight lens.
Fig. 14.1, Headlight Beam Height Adjusting Dot
14.1
Truck-Manuals.net
Headlight Aiming
2
3
A
A
B
B
7.6 m)
25 ft (
1
01/11/2012 f545850b
A. Measure the distance from the ground to the center of each headlight bulb.
B. Mark where the center of each headlight projection should appear.
1. Screen or Wall 3. Center of Left-Hand Headlight Projection
2. Center of Right-Hand Headlight Projection
Fig. 14.2, Headlight Aiming Screen/Wall
1
2
01/11/2012 f545851b
1. Low-Beam Angle Upper Limit 3. Low-Beam Angle Lower Limit

2. Ideal Low-Beam Projection
Fig. 14.3, Vertical Low-Beam Headlight Variation Limits
14.2
Truck-Manuals.net
Headlight Aiming
1
2
11/05/2002 f544235
NOTE: The right-hand side headlight bucket is shown.

The left-hand side is opposite.
1. Horizontal (inboard) Adjusting Knob
2. Vertical (outboard) Adjusting Knob
Fig. 14.4, Headlight Adjusting Knobs
Vertical Low-Beam Headlight Variation Limits

Distance Between Ground Desired Variation (Fig. 14.3, Upper Limit (Fig. 14.3, Item Lower Limit (Fig. 14.3, Item
and Headlight: in (mm) Item 2): in (mm) 1): in (mm) up 3): in (mm) down
22–36 (560–900) 0 3.9 (100) 3.9 (100)
36–48 (900–1200) 2 (50) down 2 (50) 6 (150)
48–54 (1200–1400) 2.5 (64) down 1.6 (40) 6.5 (165)
Table 14.1, Vertical Low-Beam Headlight Variation Limits
14.3
Truck-Manuals.net
15
Hybrid Electric Vehicle
Hybrid Electric Vehicle (HEV) Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1
Safety Precautions (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2
Starting, and Engine Shutdown (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2
Hybrid System Fault Lamps (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2
Emergencies (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3
Jumpstarting (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3
Towing (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3
Truck-Manuals.net
Hybrid Electric Vehicle (HEV) High-Voltage Safety Features

Overview The HEV has high-voltage cables and a service
switch on the PEC.
A hybrid electric vehicle (HEV) has both a diesel en-
gine and an electric motor. Engine torque is aug- High-voltage cables are covered in orange insulation
mented with electrical torque. The electric motor is and conduit. Each high-voltage component is tagged
powered by batteries, which are charged by regen- with a warning or danger label.
erative braking and, on vehicles equipped with the IMPORTANT: The service switch on the PEC
ePTO option, the diesel engine. should only be used for an emergency shut-
The batteries cannot move the vehicle for long dis- down, or when the service manual or trouble-
tances at highway speeds. In the event of a diesel shooting guide calls for work on the high-voltage
engine failure, drive the vehicle to a safe location as system. The service manual and troubleshooting
quickly as possible. guide for the hybrid electric system are available
Eaton Corporation developed and supplies the hybrid from www.roadranger.com.
electric system for Freightliner Trucks. The primary The red service switch is located next to the high-
system components are the hybrid drive unit (or voltage cable connections at one end of the PEC.
"HDU", which includes the electric generator/motor Pushing in the red service switch will shut down the
and automated transmission), power electronics car- engine. The hybrid system will be disabled, and the
rier (PEC), and the motor inverter/controller. Electric high-voltage batteries in the PEC, though still live,
power take-off (ePTO) and auxiliary power generator are isolated in the PEC.
(APG) components are optional on the HEV system.
NOTE: The PEC may be mounted in an area
Freightliner Trucks designed the stand-alone liquid with limited access.
cooling system required to support the operation of
Eaton’s HEV system. Its primary system components For information on emergency shutdowns, see
are the electric water pump, reservoir/expansion "Emergencies" in this chapter.
tank, radiator, electric radiator fan, and coolant
plumbing. Cooling System
Body builders will develop the components for the The HEV requires a liquid cooling system for the
PTO, the PTO plumbing, and a safety switch to pre- HDU, inverter, DC/DC Converter (if ePTO equipped),
vent the diesel engine from starting when the hood is and APG (if equipped). The HEV’s cooling system is
open. separate from the engine cooling system.
For coolant, use a mixture of 50 percent ethylene
Regenerative Braking glycol and 50 percent water.
Regenerative braking reduces vehicle speed by con-
verting some of the vehicle’s kinetic energy into elec- Electric Power Take-Off (ePTO)
tric energy to charge the hybrid system’s batteries.
The Electric Power Take-Off (ePTO) option provides
When the accelerator pedal is at idle while coasting,
standard hydraulic functions without continuous die-
or the service brake is depressed to slow the vehicle,
sel engine operation. The PTO drive power is pro-
the hybrid system charges the batteries.
vided by the hybrid motor and hybrid batteries. When
The regeneration will feel as if the brake is being the hybrid batteries deplete, the diesel engine auto-
lightly applied when you remove your foot from the matically starts to recharge them and provide PTO
accelerator pedal. The full power of the service brake drive power. Once the batteries are fully charged, the
is always available to the driver, and regenerative engine shuts down automatically. Vehicles with the
braking is automatically shut off during an ABS (an- ePTO option are designed with a safety switch to
tilock brake) event. ensure the diesel engine does not start when the
The Eaton Hybrid Control Unit will automatically shut hood is open.
off regenerative braking when the batteries are fully A DC/DC converter is required for ePTO applications
charged. to convert high-voltage DC to 12-volt DC.
15.1
Truck-Manuals.net
NOTE: To maintain a power supply from the ve- to return to the ON position. The engine will con-
hicle’s low-voltage batteries, the alternator tinue to run with the key in the ON position.
charges them when the vehicle is being driven. 5. Apply the service brake, then release the parking
brake.
Safety Precautions (HEV) 6. With the service brake applied, press the desired
The HEV has high-voltage components, including mode on the shift control to put the vehicle into
340-volt DC batteries and a 500-volt AC motor. gear.
Never cut high-voltage cables or connectors. Do not 7. Slowly release the service brake.
paint high-voltage cables.
NOTE: The vehicle may be powered by the
Avoid direct pressure wash on high-voltage connec- electric motor or the diesel engine, depending
tions (PEC, DC/DC Converter) and the air intake and
on battery charge and the demand for driveline
exhaust on the PEC.
torque. If the electric motor alone is powering
the driveline, the diesel engine will stay at idle.
Starting, and Engine Shutdown
(HEV) Engine Shutdown
The Cranking System 1. Place the transmission in neutral by selecting N
on the shift control.
The primary engine starter is the electric motor in the
HDU, which cranks the engine very quickly. The IMPORTANT: The transmission must be in neu-
back-up cranking system is the standard 12-volt tral for proper shutdown.
starter on the engine. If the hybrid system is offline 2. Set the parking brake.
or the hybrid batteries are insufficiently charged, the
vehicle will automatically use the 12-volt cranking 3. Turn the key counterclockwise to the OFF posi-
system to start the engine. tion.
NOTE: Intermittent noises such as clicking and
Starting transmission shifting may be audible from the
1. Set the parking brake. transmission while it completes a self-test and
2. Place the key in the ignition, and turn it clock-
shutdown.
wise to the ON position to initiate power to the
hybrid system. Hybrid System Fault Lamps
Wait for the gauges on the instrument panel to (HEV)
complete two sweeps (one from left to right, and
one from right to left) and return to their normal There are two lamps on the dashboard that indicate
ranges. a hybrid system fault is active — the red STOP HY-
BRID lamp and the amber CHECK HYBRID lamp.
3. Ensure the transmission is in neutral. The gear See Fig. 15.1. When the red STOP HYBRID lamp is
display should display a solid "N". illuminated, do not drive the vehicle; have it towed to
a Freightliner dealer or an authorized service center
WARNING for repairs. When the amber CHECK HYBRID lamp
is illuminated, the vehicle can still be driven, though it
Never start the engine unless the transmission is may operate without the assistance of the hybrid
in neutral and the brake is applied. Accidental electrical system.
movement of the vehicle could result in property
damage, personal injury, or death.
4. Turn the key clockwise to the START position.
The engine will crank after a brief delay. As soon
as the engine starts, release the key, allowing it
15.2
Truck-Manuals.net
• Do not cut into or open the DC/DC converter.

• Do not cut into or open the inverter.
CHECK If it is necessary to remove occupants using cutting
HYBRID equipment, avoid high-voltage cables and the PEC.
Jumpstarting (HEV)
STOP
HYBRID Jumpstarting vehicles equipped with the Eaton® Hy-
brid System is identical to Non-Hybrid vehicles,
which use the vehicle 12-volt battery system.
07/09/2008 f611013
Towing (HEV)
Fig. 15.1, Hybrid System Fault Lamps
When towing the vehicle, the output shaft of the
Emergencies (HEV) transmission must not be allowed to spin or turn. If
the vehicle is towed with the drive wheels still in con-
Emergency Shutdown tact with the road surface, the vehicle axle shafts or
driveline must be removed or disconnected. See
WARNING "Towing" in Chapter 13.
After disabling the vehicle, power is maintained

in the high-voltage electrical system for up to five
minutes. Unprotected contact with any "live" high
voltage components can cause serious injury or
even death.
There are two options for performing an emergency
shutdown. The preferred method is to turn off the
ignition key. The other option is to disconnect the
low-voltage (12-volt) vehicle batteries. In either case,
the engine will shut down, dash lights will shut down,
the hybrid electrical system will shut down, and the
high-voltage batteries in the Power Electronics Car-
rier (PEC) will remain "live" but isolated in the PEC.
NOTE: If the service switch on the PEC is ac-
cessible, it may be pushed in to shut down the
hybrid electrical system and isolate the "live"
HEV batteries in the PEC.
In Case of an Accident or Fire

If the HEV becomes involved in an accident or fire,
be aware of the following:
• Use CO2 or dry chemical extinguishers. The
batteries in the PEC are lithium ion.
• Do not cut into high-voltage cables. The high-
voltage wiring is covered in orange insulation
or convoluted tubing.
• Do not cut into or open the PEC.
15.3
Truck-Manuals.net
16
Natural Gas Vehicle
Natural Gas Vehicles, General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1
Natural Gas Vehicles, Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1
Natural Gas Fuel Tank Filling Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.2
Natural Gas Detection System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5
Natural Gas Engine Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.9
Major Repair and Replacement of Natural Gas Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.10
Truck-Manuals.net
Natural Gas Vehicle
Natural Gas Vehicles, General Natural Gas Vehicles, Safety

Information Precautions
The vehicle can be equipped with a compressed
natural gas (CNG) fuel system, or a liquefied natural DANGER
gas (LNG) fuel system. CNG is made by compress-
ing natural gas to less than 1% of its volume at stan- Natural gas is highly flammable. Failure to ob-
dard atmospheric pressure. LNG is created by con- serve the following safety precautions could lead
densing natural gas into a liquid by cooling it to to the ignition of the natural gas, which could
approximately -259°F (-162°C). CNG often contains cause serious bodily injury or death.
an odor-producing chemical, while LNG does not Follow these safety precautions when operating or
have any odor. repairing a natural gas vehicle.
When vaporized at ambient temperatures, natural • Do not start the engine if a natural gas leak is
gas is less dense than air, and it rises and disperses. detected.
However, LNG is intially heavier than air due to its
cryogenic temperature. When released in large • Do not transfer CNG from one vehicle to an-
amounts, it may drop or pool on the ground before other, as a buildup of static electricity could
its temperature rises enough to vaporize. Cold at- cause a spark and ignite the fuel.
mospheric conditions may prevent natural gas from • Do not attempt to cut any fuel supply piping
dispersing quickly when released in large amounts. components.
Natural gas is nontoxic, but it can cause asphyxiation • Avoid open flames or sparks near a natural
if present in very large concentrations. gas vehicle.
For natural gas to burn, it must first vaporize, then • Cover eyes and exposed skin when working on
mix with air in the proper proportions (flammable a natural gas fuel system or fueling a natural
range is 5 to 15% by volume in air), and then be ig- gas vehicle.
nited.
• Permit no smoking or other ignition sources
A typical natural gas fuel system consists of: within thirty feet of a natural gas vehicle.
• Fuel supply cylinders that store compressed • Have CO2 fire extinguishers (ABC minimum)
gas at high pressure (CNG), or a tank that located in a highly visible and easily accessible
stores liquefied gas at an extremely low tem- location.
perature (LNG).
• Use Purple-K powder (PKP) or a similar dry
• A vaporizor or heat exchanging device that
powder to extinguish an LNG fire. Do not at-
changes LNG to gaseous form (LNG fuel sys- tempt use water around an LNG fire.
tems only).
• Always purge the fuel lines before performing
• Pressure relief and manual fuel shutoff valves. maintenance or repairs on a natural gas fuel
• A filling connection with a check valve that pre- system. To purge the lines, close the manual
vents the gas from flowing back out of the fuel fuel shutoff valve, and start the engine. Let the
filling line. vehicle idle until the fuel lines are empty and
the engine stops.
• High-pressure and low-pressure fuel filters.
• Always use a natural gas detector to test the
• A pressure control regulator that reduces the system for leaks, whether an odor is present or
high fuel tank or cylinder pressure to the lower not. Routinely inspect the fuel filtering and
pressure needed for the engine. regulating mechanisms, and the fuel lines. A
• A fuel contents gauge that indicates the fuel bubble solution can be used to pinpoint the
supply in the tank or cylinders. exact location of leaks.
16.1
Truck-Manuals.net
Natural Gas Vehicle
• Always tighten fasteners and fuel connections CNG Temperature/Pressure Compensation Values
to the required torque specification. Overtight-
Fill Station Pressure Set Point
ening or undertightening could cause leaks. Temperature:
3000 psi (20 684 3600 psi (24 821
°F (°C)
• Close the fuel shutoff valve(s) before perform- kPa) Set Point kPa) Set Point
ing maintenance and repairs. 100 (37.8) 3415 (23 546) 4086 (28 172)
• Do not store a natural gas vehicle indoors for 90 (32.2) 3276 (22 587) 3909 (26 952)
any extended period of time. Do not bring a 80 (26.7) 3138 (21 636) 3754 (25 883)
natural gas vehicle indoors unless the work- 70 (21.1) 3000 (20 684) 3600 (24 821)
shop is equipped with a methane detection and 60 (15.6) 2861 (19 726) 3445 (23 752)
ventilation system. 50 (10) 2723 (18 774) 3288 (22 670)
40 (4.4) 2584 (17 816) 3131 (21 587)
In Case of Emergency 30 (-1.1) 2446 (16 865) 2973 (20 498)
If a vehicle has sustained damage or a leak has 20 (-6.7) 2307 (15 906) 2814 (19 402)
been discovered: 10 (-12.2) 2169 (14 955) 2655 (18 306)
0 (-17.8) 2031 (14 003) 2495 (17 202)
1. Turn the ignition switch off, set the parking brake, -10 (-23.3) 1893 (13 052) 2336 (16 106)
and disconnect the battery. -20 (-28.9) 1755 (12 100) 2180 (15 031)
2. Remove all ignition sources from the area sur- -30 (34.4) 1616 (11 142) 2024 (13 955)
rounding the vehicle. -40 (-40) 1477 (10 184) 1868 (12 879)
3. If it is safe to do so, close all fuel shutoff valves. Table 16.1, CNG Temperature/Pressure Compensation
Values
4. Open the vehicle doors to introduce fresh air.
5. Use a natural gas detector to identify leaks in the Use the following steps to fuel a CNG vehicle.
fuel system.
1. Shut down the engine and apply the parking
brake.
Natural Gas Fuel Tank Filling
IMPORTANT: Close all windows and doors dur-
Procedures ing the fueling process. Keeping windows and
CNG Vehicle Fueling doors closed allows for easier leak detection
inside the cab after fueling.
CNG is moved from the fuel station storage tanks to
the vehicle cylinders through a metered dispenser.
During fueling, as pressure inside of the vehicle cyl-
WARNING
inders increases, so does the temperature. The dis-
Natural gas fuel tanks, lines, and valves are al-
penser shuts off when it determines the CNG cylin-
ways pressurized. Always observe safety precau-
ders are full.
tions. Failure to do so could lead to loss of con-
CNG fuel cylinders cannot be filled to their full capac- trol over a filling hose or to ignition of the natural
ity of 3600 psi (24 800 kPa) in cooler weather. Since gas, which could cause serious bodily injury,
temperature change causes gas to expand and con- death, or severe property damage.
tract, less pressure in the cylinders on a cold day is
2. Ensure all fuel cylinder shutoff valves are open.
equal to the same amount of gas at a higher pres-
sure on a warm day. The fuel station dispenser has a See Fig. 16.1.
temperature-pressure compensating device, which 3. Ensure the vehicle fuel system main shutoff
accounts for ambient temperature during fueling. See valve is open.
Table 16.1 for approximate full cylinder pressures at
various temperatures. 4. Open the CNG fuel panel access door and re-
move the dust cap from the vehicle fuel fill port.
16.2
Truck-Manuals.net
Natural Gas Vehicle
tion emergency shut-off switch to cease the flow

1 2
of CNG.
9. Switch on the service pump. A slight hissing
noise may be heard as the fuel cylinders fill.
10. Watch the pressure gauge on the service pump.
When the gauge reads approximately 3600 psi
(24 800 kPa), or when the fill pressure stops
3 4 climbing, the CNG cylinders are full. The service
pump will shut itself down automatically. See
Table 16.1 for pressure compensation values
based on ambient temperatures.
11. Move the selector knob on the service pump to
the VENT position, if equipped. A short hiss will
8 7 6 5 be heard as a small amount of natural gas is
vented into the hose.
WARNING
Do not attempt to remove the fill station nozzle
from the tank fill fitting until venting of pressure
is noted. If no venting occurs, ask for assistance
from the station attendant. Removing an un-
vented coupling could result in an uncontrolled
04/22/2010 f470554 hose, which could lead to property damage or
1. Fuel Cylinder Storage Box personal injury.
2. Fuel Cylinder Shutoff Valves (qty 5)
3. High-Pressure Gauge 12. Remove the station dispensing nozzle from the
4. Low-Pressure Gauge vehicle fill port.
5. Fuel Fill Port
13. Install the dust cap on the vehicle fuel fill port
6. Dust Cap
7. Manual Shutoff Valve and close the fuel panel access door.
8. Fuel Panel Access Door
LNG Vehicle Fueling
Fig. 16.1, CNG Fuel Cylinder Storage Box (5-cylinder
system shown) The LNG fuel tank is designed to be filled from any
LNG fuel source that has a 100 micron or finer fuel
5. Ensure the O-ring is present inside the fuel fill filter and a fuel delivery pressure between 120 and
port. If the O-ring has been dislodged or is miss- 225 psi (827 and 1551 kPa).
ing, the station dispensing nozzle will not con-
nect securely to the fill port. The LNG fuel tank is designed to be top-filled
through a single hose with no vent return. As cold
6. Turn the selector knob on the service pump to LNG is sprayed into the vapor space of the tank, the
the VENT position, if equipped. cold liquid condenses the vapor and creates space
for itself inside the tank, eliminating any need to vent
7. Connect the quick coupling on the dispensing
during the filling process.
nozzle securely to the vehicle fuel fill port.
The LNG tank is equipped with a small internal ul-
8. Turn the selector knob on the service pump to lage tank for vapor space, which allows for fuel ex-
the FILL position, if equipped. pansion and increases vehicle standby time. When
IMPORTANT: If at any time the service pump or an LNG tank is full, fuel can continue to flow into the
vehicle begins to vent CNG uncontrollably, notify ullage tank. However, if the ullage tank is completely
a station attendant or activate the service sta- filled during fueling, standby time will be reduced to
16.3
Truck-Manuals.net
Natural Gas Vehicle
zero and the primary relief valve will open almost 2 3

immediately after fueling, allowing excess LNG vapor
to escape. If fueling is stopped when the ullage tank
is empty (i.e., the fuel tank has sufficient vapor space 4
to accommodate fuel expansion due to temperature
increase), the vehicle will have approximately one
week of standby time before venting will occur.
Use the following steps to fuel an LNG vehicle. 6
1. Shut down the engine and apply the parking
brake.
IMPORTANT: Close all windows and doors dur-
ing the fueling process. Keeping windows and
doors closed allows for easier leak detection
inside the cab after fueling.
5
1
WARNING
05/29/2009
6 f470534
Liquefied natural gas is a cryogenic liquid stored
1. Fuel Fill Fitting 4. Fill Vent Fitting
at approximately -259°F (-162°C). Cryogenic 2. Fuel Outlet Line 5. Shroud Cover
burns can be caused by coming into contact with 3. Primary Relief Vent 6. Shroud Cover Latches
the pressurized liquid stream, or by coming into Line
contact with fuel system components that have
been cooled to cryogenic temperatures. Always Fig. 16.2, LNG Fuel Tank
wear gloves and a face shield, and cover ex-
posed skin when fueling. erated in approximately ten days, is considered
to be a hot tank. When fueling a hot tank, LNG
2. Remove the fuel fill fitting dust cap. See entering the tank will immediately vaporize,
Fig. 16.2.
causing tank pressure to spike above 250 psi
3. Using compressed air, remove any dirt, debris, or (1724 kPa) and automatically shutting down the
water that may have collected in the fuel fill fit- station fuel pump. To prevent the pump from
ting and the station dispensing nozzle. Contami- shutting down, connect a vent line to the fill vent
nants in the fuel system can cause drivability fitting on the LNG tank to capture escaping
problems. vapor, then open the shroud cover and open the
vapor shutoff valve (Fig. 16.3, Item 2).
WARNING
6. Open the station’s fill valve, if equipped, and
Natural gas fuel tanks, lines, and valves are al- start fueling. Monitor the flow or line pressure as
ways pressurized. Always observe safety precau- filling progresses. When filling begins, line pres-
tions. Failure to do so could lead to loss of con- sure will spike quickly until the vehicle tank cools
trol over a filling hose or to ignition of the natural down. The flow and pressure will then remain
gas, which could cause serious bodily injury, stable during the remainder of the filling
death, or severe property damage. procedure.
4. Connect the station fueling nozzle to the tank IMPORTANT: When fueling a hot tank, initially
fuel fill fitting. put 5 to 10 gallons (19 to 37 liters) of LNG in
the tank and manually stop the fueling process.
5. Connect an electrical ground clamp and cable to
the fuel tank.
Drive the vehicle for 15 to 20 minutes to cool
the tank and reduce tank pressure, then con-
IMPORTANT: An LNG tank which is first in- tinue fueling the tank to full.
stalled, or is on a vehicle that has not been op-
16.4
Truck-Manuals.net
Natural Gas Vehicle
8
Natural Gas Detection System
7 9
6 10 A gas detection system is standard equipment in all
Daimler Trucks natural-gas-fueled vehicles. This sys-
5 tem has a sensor in the engine compartment and
11 one in the cab, both situated in high areas to detect
natural gas buildup as a result of leaks.
12 The AMGaDS III Plus is a natural gas detection sys-
tem. This device is meant to serve as a supplemen-
tal warning only. It is not intended to replace stan-
dard safety practices that should be conducted
4 around flammable gases.
3 IMPORTANT: To function properly, the gas de-

tection system must be powered at all times.
2 The gas detection system is directly powered by
the batteries, and can only be powered off by
1 disconnecting the batteries.When servicing a
natural-gas-fueled vehicle, disconnect the bat-
05/05/2010 f470533 teries only when necessary, and do not leave
1. Pressure Control Regulator the batteries disconnected for extended periods
2. Vapor Shutoff Valve of time.
3. Fuel Fill Hose
4. Secondary Relief Valve (red cap) The lower flammability limit (LFL) is the smallest
5. Fuel Fill Fitting amount of the gas that supports a flame when mixed
6. Fuel Level Sender Box with oxygen and ignited. Zero percent (0%) LFL indi-
7. Primary Relief Valve cates a gas-free atmosphere. One hundred percent
8. Tank Pressure Gauge (100%) LFL indicates that gas concentration has
9. Fill Vent Fitting reached its lower flammability limit (5% gas in air by
10. Excess Flow Valve volume). The red warning light and audible alarm
11. Fuel Shutoff Valve (liquid) located in the overhead console activate when a sen-
12. Fill Check Valve sor detects gas fumes in concentrations above 50%
Fig. 16.3, LNG Fuel Tank Plumbing Components LFL, and should allow ample time to utilize safety
procedures. However, individuals with special needs
7. When the tank is full, the line pressure will rap- should review the system with a professional safety
idly spike and the flow rate will fall. When a pres- engineer.
sure rise or flow rate drop is observed, close the
station’s fill valve, if equipped. Alarm Procedure
NOTE: Do not over-fill an LNG tank. If the ul- Before operating the vehicle, the driver must be fa-
lage tank is completely filled during fueling, tank miliar with the procedures as shown on the interior
standby time will be reduced to zero and the sticker on the overhead panel (Fig. 16.4) and the
primary relief valve will open almost immediately exterior sticker on the door (Fig. 16.5).
after fueling. IMPORTANT: If an audible alarm activates, do
8. Disconnect the station hose from the tank fuel fill not operate any electrical switch, including
fitting. lights. Avoid causing sparks and stay away from
arcing switches and equipment. Do not use a
9. Disconnect the electrical ground clamp and cable
telephone, including cellular phones or any
from the fuel tank.
types of portable communication or electronic
10. Install the dust cap on the tank fuel fill fitting. devices that have a battery.
16.5
Truck-Manuals.net
Natural Gas Vehicle
If outside the vehicle when the audible alarm acti-

vates, do not open the cab door or hood.
In the event of an audible alarm, immediately follow
these procedures, as allowed by conditions:
1. Immediately shut off all engines. Extinguish any
cigarettes, pilot lights, flames, or other sources of
ignition in the area and adjacent areas.
2. Manually close all fuel shutoff valves, including
those on the LNG tank or CNG cylinders.
3. If the vehicle is indoors (as in a service shop),
immediately open windows and doors to provide
extra ventilation to the area. Do not start the en-
gine or any other type of equipment until the gas
leak is corrected and the area cleared of natural
gas.
04/28/2009 f080157
4. Evacuate the area.
Fig. 16.4, Interior Warning Sticker
5. Check the fuel lines, LNG tank/CNG cylinders,
and fittings to locate the leak. After the area is
cleared of natural gas and the alarm is no longer
active, have the vehicle inspected by a qualified
technician.
IMPORTANT: Do not consider the area clear
until all alarm indicators are off, and the alarm
panel light returns to green.
Sensors
Gas detection sensors are located on the cab over-
head console and in the engine compartment on the
frontwall. The sensors are located in high areas,
where rising gas vapors will pass by or accumulate.
If the system detects that one of the sensors has
been disconnected or has malfunctioned, the sensor
fault light for that zone will illuminate. A failed sensor
may trigger and lock on an alarm. If a fault condition
or locked alarm continues after the sensor’s connec-
tion and wiring integrity has been verified, replace
the sensor.
The sensors are sensitive to all hydrocarbon vapors.
An alarm may be triggered by the use of chemicals
04/28/2009 f080158 such as cleaners, paint, polish, lacquer, gasoline,
silicone, silicone spray, or other harsh chemicals.
Fig. 16.5, Exterior Warning Sticker The sensors will also detect hydrogen fumes from an
If the vehicle is in motion when the audible alarm overcharged battery. If a sensor sends an alarm, but
activates, bring it to a safe stop, shut down the en- no gas fumes are present, check for recent use of
gine, and exit the vehicle. Do not open the hood. chemicals or a battery charger.
16.6
Truck-Manuals.net
Natural Gas Vehicle
level detection, and the large green light on the

NOTICE alarm panel will remain illuminated.
Silicone-based chemicals and cleaners will per- • Significant Level: If either sensor detects gas
manently disable the sensors. When cleaning the fumes at a concentration greater than 50% to
vehicle, cover the sensors with a plastic cover- 60% LFL (2.5% gas in air by volume), the
ing. Keep the sensors covered until the area has small red light next to the SIGNIFICANT indi-
been cleared of any cleaning fumes. cator for that zone will flash. After approxi-
mately 15 seconds, the large green light on the
Harsh chemicals and extremely high tempera- alarm panel will switch off, the red light will illu-
tures may damage the sensor. minate, and the buzzer will sound. All alarm
Puncture of or damage to the seal located inside indicators will remain on as long as fumes are
the sensor housing will significantly shorten the detected.
sensor life. • Sensor Fault: If the system detects that either
Frequent exposure to high concentrations of gas of the sensors has been disconnected or has
will accelerate sensor deterioration. malfunctioned, an amber light next to the Sen-
sor Fault indicator for that zone will illuminate.
Overhead Console The control module also has buttons used to test or
reset the the control module after an alarm. Red
The overhead console consists of an alarm panel on lights next to each button indicate when they are en-
the right side and the control module on the left side. gaged.
The alarm panel has a green light, a red light, a
• Shutdown Reset: If an alarm has been acti-
buzzer, and a sensor. See Fig. 16.6. It is located
vated and the Relay Engaged light is illumi-
within view from outside of the vehicle. The large
nated, the Shutdown Reset button will reset
green light is continuously illuminated during normal
the internal relay. Press the Shutdown Reset
operating conditions.
button only after the gas has cleared, the
Before entering the vehicle, always verify that the buzzer has turned off, and the alarm panel
green light is illuminated. If the green light is not illu- light has returned to green.
minated, do not enter the vehicle. Complete the
• Push To Silence: If an alarm has been acti-
alarm procedure previously outlined.
vated, the Push To Silence button will silence
The alarm panel meets the California Highway Patrol the buzzer.
Title 13-2008 and NFPA 52 2010 requirements. All
drivers and technicians using it should be trained re- See Table 16.2 for the functions of all lights and but-
garding the red and green lights, and the audible tons on the overhead console.
warning.
Testing
The control module, located on the left side of the
overhead console, contains the status lights and con- Daimler Trucks North America strongly recommends
trol buttons for the system. The areas that the sen- that all operators follow California Code of Regula-
sors monitor are defined as Zone 1 (cab) and Zone 2 tions (CCR) inspection requirements, regardless of
(engine compartment). The control module has lights where the vehicle is operated. Per Title 13 CCR §
assigned to each zone that will illuminate if a sensor 935 (2), gas detection systems should be tested
detects a trace level leak (between 20% and 30% three times per calendar year at equal intervals. The
LFL), a significant level leak (above 50% LFL), or if a testing procedure should simulate the same operat-
sensor is disconnected or malfunctioning. ing environment in which the vehicle is used, with the
same gaseous fuel.
• Trace Level: If either sensor detects gas fumes
at a concentration greater than 20% to 30%
LFL (1% gas in air by volume), the amber light
next to the Trace indicator for that zone will
flash. There is no buzzer alarm for a trace
16.7
Truck-Manuals.net
Natural Gas Vehicle
5 6
7
4
AMGaDS III Plus Gas Detection System
Power Push Silence

Gas Concentration: To Engaged
Silence
SIGNIFICANT 10 11
3 Trace
12 13
Zo
Zo
Shutdown Relay
ne
ne
Reset Engaged
1
Sensor Fault
Push To Test
2 1 9
04/28/2009 f611034
1. Test Button 6. Silence Button 10. Buzzer Alarm
2. Sensor Fault Indicator Lights 7. Silenced Engaged Light 11 Red Light
3. Zone 1 Leak Indicator Lights 8. Relay Engaged Light 12. Green Light
4. Power Indicator Light 9. Shutdown Reset Button 13. Sensor
5. Zone 2 Leak Indicator Lights
Fig. 16.6, AMGaDS III Plus Overhead Console
Control Module Functions

Item Display Function Action Required
Illuminated System is on. None required.
Ensure the batteries are
Green Power Light connected and replace any blown
Detection system is not
Unlit fuses. If the gas detection system
functioning.
is still not functioning, replace the
system immediately.
Suspend vehicle operation
SIGNIFICANT Gas Dangerous gas concentration
Red (illuminated) immediately and follow alarm
Concentration Lights detected.
procedures.
Trace Gas Concentration Use caution and monitor the
Amber (flashing) Minor gas concentration detected.
Lights system.
Off Sensor is functioning properly. None required.
Sensor Fault Lights
On Sensor has malfunctioned. Replace the sensor immediately.
16.8
Truck-Manuals.net
Natural Gas Vehicle
Control Module Functions

Item Display Function Action Required
Press to reset the system only
after the gas has cleared, the
Resets the system after an alarm
Shutdown Reset Button — buzzer has turned off, and the
activation.
alarm panel light has returned to
green.
Relay is engaged and test or
On Press the Shutdown Reset button.
Relay Engaged Light alarm is being cleared.
Off Normal condition. None required.
Press and hold for one minute to
Tests the overhead console
Test Button — to activate a test of all overhead
operation and circuitry.
console components.
Silence Button — Silences the alarm buzzer. Press to silence the alarm buzzer.
Suspend vehicle operation
Indicates the buzzer is active but
On immediately and follow alarm
Silence Engaged Light silenced.
procedures.
Off Normal condition. None required.
Table 16.2, Control Module Functions
Test results validating the performance of the gas such as butane or propane does not satisfy CCR §
detection system within the parameters established 935 (2) or NFPA 52 regulations.
by the component manufacturer and NFPA 52 2010
should be maintained as a permanent part of the ve- Expose each sensor to certified test gas for at least
hicle service records. Use of alcohol, propane, and thirty seconds. The system will proceed through the
other harsh liquids or gases are not acceptable alarm procedure consistent with a significant leak
methods for testing. and the buzzer will sound after approximately fifteen
seconds. If a sensor fails to respond after exposure
Always test the system and sensors after any com- to the test gas, replace the sensor.
ponent has been replaced, or if the vehicle has been
involved in an accident or fire. Ensure that the gas Natural Gas Engine Starting
detection system is wired directly to the battery.
It is recommended that the highest level of safety NOTE: Before starting the engine, read Chap-
validation be utilized if there are multiple validation ter 3 for detailed information on how to read the
requirements in the state or locality where the vehicle instruments and Chapter 4 for detailed informa-
is operated or domiciled. tion on how to operate the controls. Read the
operating instructions in the engine manufactur-
Overhead Console Test er’s operation manual before starting the en-
Press and hold the Push To Test button for one min- gine.
ute. The system will proceed with a self-diagnostic 1. Before engine start-up, complete the engine pre-
test that will include illumination of the Trace and trip and post-trip inspections and maintenance
SIGNIFICANT gas concentration lights, and the sen- procedures in Chapter 11.
sor fault lights. Verify the large red light and buzzer
activate, and that all lights illuminate or flash to en- 2. Ensure the fuel shutoff valve is open.
sure that all bulbs are operational. 3. Set the parking brake.
Sensor Test 4. Ensure that the transmission shift control is in
Neutral (N), Park (P), or the Park Brake (PB) po-
The gas detection system sensors must be tested sition.
using certified test gas, which can be purchased as
part of a test kit. Testing with alcohol or heavy gases
16.9
Truck-Manuals.net
Natural Gas Vehicle
5. Without starting the engine, turn the ignition Replace any leaking or damaged fuel tanks/cylinders
switch to the ON position (Fig. 16.7). The elec- and fuel lines; repair or replace leaking or damaged
tronic gauges on the instrumentation control unit fittings. Install parts and components in accordance
(ICU) will complete a full sweep of their dials, the with the manufacturer’s instructions.
warning and indicator lights will illuminate, and
the buzzer will sound for three seconds.
09/12/2001 f610509
Fig. 16.7, Ignition Switch Positions
6. Turn the ignition switch to the START position.

Press down on the clutch pedal, if equipped, but
do not press down on the accelerator pedal.
Release the key the moment the engine starts.
7. Bring the engine up to operating speed gradually
as it warms up and develops stable oil pressure.
If the vehicle has not been operated previously in
a 24-hour period, allow the vehicle to idle for five
minutes.
NOTICE
Do not rev the engine if the oil pressure gauge
indicates no oil pressure. Shut down the engine
within approximately ten seconds to avoid engine
damage.
8. Check the oil pressure gauge for any drop in lu-
bricating oil pressure or mechanical malfunction
in the lubricating oil system.
Major Repair and Replacement

of Natural Gas Components
If a natural-gas-fueled vehicle is involved in an acci-
dent, remove the fuel tank or cylinders from service
and have them inspected by a qualified technician.
16.10
Truck-Manuals.net
Index
Subject Page Subject Page

A Exiting from the Driver’s Side . . . . . . . . . . . . . . . 2.4
Exiting from the Passenger’s
Adjustable Steering Column . . . . . . . . . . . . . . . . . 4.13 Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5
Adjusting Headlight Aim . . . . . . . . . . . . . . . . . . . 14.1 Cab Entry and Exit, Vehicles
Air Brake System . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 With Two Steps . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Air Brake System, General Entering from the Driver’s
Information . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Air Brake System Operation . . . . . . . . . . . . . . . . 9.2 Entering from the
Automatic Slack Adjusters . . . . . . . . . . . . . . . . . 9.4 Passenger’s Side . . . . . . . . . . . . . . . . . . . . . 2.3
Allison MD Series . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Exiting from the Driver’s Side . . . . . . . . . . . . . . . 2.3
Operating Instructions, MD Exiting from the Passenger’s
Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . 8.5 Cab Washing and Polishing . . . . . . . . . . . . . . . . . 12.1
Allison On-Highway Canadian Motor Vehicle Safety
Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Standard Labels . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Operating Instructions, On- Care of Chrome Parts . . . . . . . . . . . . . . . . . . . . . 12.1
Highway Transmissions . . . . . . . . . . . . . . . . . 8.4 Care of Exterior Lights . . . . . . . . . . . . . . . . . . . . 12.1
Range Inhibit Indicator, 2000 Care of Fiberglass Parts . . . . . . . . . . . . . . . . . . . 12.1
and 2400 Series . . . . . . . . . . . . . . . . . . . . . . 8.3 Checking Headlight Aim . . . . . . . . . . . . . . . . . . . 14.1
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . 8.3 Climate Control Panel . . . . . . . . . . . . . . . . . . . . . . 6.1
All-Wheel-Drive Controls, Accessory Heaters . . . . . . . . . . . . . . . . . . . . . . 6.4
Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11 Air Conditioning, Optional . . . . . . . . . . . . . . . . . 6.4
AWD Operation Switch . . . . . . . . . . . . . . . . . . 4.12 Air Selection Switch . . . . . . . . . . . . . . . . . . . . . 6.1
AWD Range Switch . . . . . . . . . . . . . . . . . . . . 4.12 Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3
Fan Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1
B Fresh Air Mode . . . . . . . . . . . . . . . . . . . . . . . . 6.3
Recirculation Mode . . . . . . . . . . . . . . . . . . . . . 6.3
Back-of-Cab Access . . . . . . . . . . . . . . . . . . . . . . . 2.5 Temperature Control Switch . . . . . . . . . . . . . . . . 6.3
Climbing Down from Back- Clutches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1
of-Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Entering Back-of-Cab . . . . . . . . . . . . . . . . . . . . 2.6 Clutch Adjustments . . . . . . . . . . . . . . . . . . . . . 8.2
Battery Access . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 Clutch Lubrication . . . . . . . . . . . . . . . . . . . . . . 8.2
Battery Compartment . . . . . . . . . . . . . . . . . . . . 2.6 Clutch Operation . . . . . . . . . . . . . . . . . . . . . . . 8.1
Cab (Battery) Isolation Clutch Wear . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 Sachs Hydraulic Clutch . . . . . . . . . . . . . . . . . . . 8.2
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13 Cold-Weather Operation . . . . . . . . . . . . . . . . . . . 7.10
Meritor™ WABCO® Antilock Cold-Weather Starting . . . . . . . . . . . . . . . . . . . . . 7.9
Braking System (ABS) . . . . . . . . . . . . . . . . . 4.13 Component GWR Label . . . . . . . . . . . . . . . . . . . . 1.1
Parking Brake Control Valve . . . . . . . . . . . . . . . 4.13 Component Information Label . . . . . . . . . . . . . . . . 1.1
Trailer Air Supply Valve . . . . . . . . . . . . . . . . . . 4.13 Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . 7.11
Trailer Brake Lever . . . . . . . . . . . . . . . . . . . . . 4.13 Dash-Mounted Switches . . . . . . . . . . . . . . . . . 7.11
Shift Knob Controls, Optional . . . . . . . . . . . . . . 7.12
C
Cab Amenities . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11
D
Cab Storage . . . . . . . . . . . . . . . . . . . . . . . . . 5.11 Daily Pretrip Inspection and
Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . 5.11 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3
Cab Door Locks and Handles . . . . . . . . . . . . . . . . 2.1 Cab Inspection . . . . . . . . . . . . . . . . . . . . . . . . 11.7
Cab Entry and Exit, Vehicles Engine Compartment
With One Step . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6
Entering from the Driver’s Natural Gas Fuel System
Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Inspection, If Equipped . . . . . . . . . . . . . . . . 11.10
Entering from the Saddle Tank Area
Passenger’s Side . . . . . . . . . . . . . . . . . . . . . 2.5 Inspections . . . . . . . . . . . . . . . . . . . . . . . . . 11.6
I-1
Truck-Manuals.net
Index

Suspension and Slack Manual Mode (MAN) . . . . . . . . . . . . . . . . . . . . 8.23
Adjuster Inspection . . . . . . . . . . . . . . . . . . . . 11.3 Power Down . . . . . . . . . . . . . . . . . . . . . . . . . 8.22
Wheel and Tire Inspection . . . . . . . . . . . . . . . . 11.3 Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.22
Dashboard Care . . . . . . . . . . . . . . . . . . . . . . . . 12.1 Reverse (R) . . . . . . . . . . . . . . . . . . . . . . . . . 8.22
Diesel Exhaust Fluid and Tank, Shuttle Shifting . . . . . . . . . . . . . . . . . . . . . . . 8.24
EPA10 and Newer Engines . . . . . . . . . . . . . . . . . 7.3 Skip Shifting . . . . . . . . . . . . . . . . . . . . . . . . . 8.24
DEF Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Eaton® Fuller® Straight-Shift
DEF Warnings and Engine Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8
Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 General Information,
Diesel Exhaust Fluid . . . . . . . . . . . . . . . . . . . . 7.3 Straight-Shift . . . . . . . . . . . . . . . . . . . . . . . . 8.8
Fuel/DEF Gauge . . . . . . . . . . . . . . . . . . . . . . . 7.4 Operation, Straight-Shift . . . . . . . . . . . . . . . . . . 8.8
Driver Message Center . . . . . . . . . . . . . . . . . . . . . 3.7 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Driving Screens . . . . . . . . . . . . . . . . . . . . . . . . 3.7 Emergencies (HEV) . . . . . . . . . . . . . . . . . . . . . . 15.3
Parked Screens/Menus . . . . . . . . . . . . . . . . . . . 3.7 Emergency Shutdown . . . . . . . . . . . . . . . . . . . 15.3
In Case of an Accident or
E Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3
Emergency Filter Replacement,
Eaton Fuller AutoShift™ Davco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1
Automated Transmissions . . . . . . . . . . . . . . . . . 8.12 Emergency Kit, Optional . . . . . . . . . . . . . . . . . . . 13.1
Automatic Mode . . . . . . . . . . . . . . . . . . . . . . . 8.13 Emergency Starting With
Manual Mode . . . . . . . . . . . . . . . . . . . . . . . . 8.13 Jumper Cables . . . . . . . . . . . . . . . . . . . . . . . . 13.2
Push-Button Shift Selector . . . . . . . . . . . . . . . . 8.13 Emission Labels . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Selecting Gears . . . . . . . . . . . . . . . . . . . . . . . 8.14 Aftertreatment System
Eaton Fuller Range-Shift Indicators Label . . . . . . . . . . . . . . . . . . . . . . 1.2
Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . . 8.9 Certified Clean Idle Label . . . . . . . . . . . . . . . . . 1.3
General Information, Range- EPA Noise Emission Control
Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.9 Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Operation, Deep-Reduction Vehicle Emission Control
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.11 Information Label . . . . . . . . . . . . . . . . . . . . . 1.3
Operation, Range-Shift . . . . . . . . . . . . . . . . . . 8.10 Emissions and Fuel Efficiency . . . . . . . . . . . . . . . . 7.1
Eaton Fuller UltraShift ATS Warning Lamps . . . . . . . . . . . . . . . . . . . . 7.3
Automated Transmissions . . . . . . . . . . . . . . . . . 8.15 EPA07 Engines . . . . . . . . . . . . . . . . . . . . . . . . 7.1
General Information, EPA10 and Newer Engines . . . . . . . . . . . . . . . . 7.1
UltraShift ASW . . . . . . . . . . . . . . . . . . . . . . 8.15 Greenhouse Gas Emissions
General Information, and Fuel Consumption
UltraShift DM . . . . . . . . . . . . . . . . . . . . . . . 8.16 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1
Operation, UltraShift . . . . . . . . . . . . . . . . . . . . 8.16 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3
UltraShift Diagnostics . . . . . . . . . . . . . . . . . . . 8.20 Regeneration . . . . . . . . . . . . . . . . . . . . . . . . . 7.1
Eaton Fuller UltraShift PLUS Engine Braking . . . . . . . . . . . . . . . . . . . . . . . . . 7.13
Automated Transmissions . . . . . . . . . . . . . . . . . 8.21 Engine Brake Operation . . . . . . . . . . . . . . . . . 7.14
Auto Neutral . . . . . . . . . . . . . . . . . . . . . . . . . 8.24 Engine Break-In . . . . . . . . . . . . . . . . . . . . . . . . . 7.9
Auto Start Gear Selection Engine Operation . . . . . . . . . . . . . . . . . . . . . . . . . 7.9
and Override . . . . . . . . . . . . . . . . . . . . . . . . 8.24
Normal Operation . . . . . . . . . . . . . . . . . . . . . . 7.10
Automatic Mode (AUTO) . . . . . . . . . . . . . . . . . 8.22
Safety and Environmental
Automatic Traction Control . . . . . . . . . . . . . . . . 8.25 Considerations . . . . . . . . . . . . . . . . . . . . . . . 7.9
Clutch Abuse Protection . . . . . . . . . . . . . . . . . 8.23 Engine Shutdown . . . . . . . . . . . . . . . . . . . . . . . . 7.11
Coasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.25 Engine Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7
Creep Mode . . . . . . . . . . . . . . . . . . . . . . . . . 8.24 Enhanced Stability Control . . . . . . . . . . . . . . . . . . 9.6
Engine Overspeed Exhaust Braking Systems . . . . . . . . . . . . . . . . . . 7.15
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . 8.24
Exhaust Brake Switch . . . . . . . . . . . . . . . . . . . 7.15
Hill Start Aid . . . . . . . . . . . . . . . . . . . . . . . . . 8.24
Mercedes-Benz Exhaust
Load-Based Shifting . . . . . . . . . . . . . . . . . . . . 8.25 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.15
Low (L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.23 Pacbrake® Exhaust Brake . . . . . . . . . . . . . . . . 7.16
I-2
Truck-Manuals.net
Index

F Regenerative Braking . . . . . . . . . . . . . . . . . . . 15.1
Hybrid System Fault Lamps
Federal Motor Vehicle Safety (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2
Standard Labels . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Hydraulic Brake System . . . . . . . . . . . . . . . . . . . . 9.4
Fifth Wheel Coupling . . . . . . . . . . . . . . . . . . . . . 10.1 Hydraulic Brake System,
Fontaine and Holland Fifth General Information . . . . . . . . . . . . . . . . . . . . 9.4
Wheels Coupling . . . . . . . . . . . . . . . . . . . . . 10.1 Hydraulic Brake System
Jost Fifth Wheel Coupling . . . . . . . . . . . . . . . . 10.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4
Fifth Wheel Slide . . . . . . . . . . . . . . . . . . . . . . . . 10.7
Air Slide Operation . . . . . . . . . . . . . . . . . . . . . 10.9
Manual Slide Operation . . . . . . . . . . . . . . . . . . 10.7
I
Fifth Wheel Uncoupling . . . . . . . . . . . . . . . . . . . . 10.4 Ignition Switch and Key . . . . . . . . . . . . . . . . . . . . 4.1
Air-Actuated Uncoupling . . . . . . . . . . . . . . . . . 10.5 Instrumentation Control Unit . . . . . . . . . . . . . . . . . . 3.1
Manual Uncoupling . . . . . . . . . . . . . . . . . . . . . 10.4 Audible Alerts . . . . . . . . . . . . . . . . . . . . . . . . . 3.2
Fifth Wheels, General Ignition Sequence . . . . . . . . . . . . . . . . . . . . . . 3.1
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Air-Suspension Dump Valve . . . . . . . . . . . . . . . 10.1 Air Intake Restriction Gauge . . . . . . . . . . . . . . . 3.9
Fifth Wheel Lubrication . . . . . . . . . . . . . . . . . . 10.1 Ambient Temperature Gauge . . . . . . . . . . . . . . . 3.9
Fire Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . 13.1 Coolant Temperature Gauge . . . . . . . . . . . . . . 3.10
Fire in the Cab . . . . . . . . . . . . . . . . . . . . . . . . . 13.7 Engine Oil Pressure Gauge . . . . . . . . . . . . . . . 3.10
In Case of a Cab Fire . . . . . . . . . . . . . . . . . . . 13.7 Engine Oil Temperature
Freightliner SmartShift Shift Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.15 Fuel Gauge, Pre-EPA10 . . . . . . . . . . . . . . . . . 3.11
General Information, Fuel/Diesel Exhaust Fluid
SmartShift . . . . . . . . . . . . . . . . . . . . . . . . . 8.15 (DEF) Gauge, EPA10 and
Fuse Identification . . . . . . . . . . . . . . . . . . . . . . . . 2.8 Newer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11
Main Fuse Box/PDM . . . . . . . . . . . . . . . . . . . . 2.8 Primary and Secondary Air
Trailer and Taillight Fuse Pressure Gauges . . . . . . . . . . . . . . . . . . . . . 3.12
Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . 3.12
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12
G Transmission Fluid
Temperature Gauge . . . . . . . . . . . . . . . . . . . 3.12
Grab Handles and Access Turbocharger Boost
Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . 3.13
Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13
H
Hazard Warning Lights . . . . . . . . . . . . . . . . . . . . 13.1
J
Heater/Air Conditioner Control Jumpstarting (HEV) . . . . . . . . . . . . . . . . . . . . . . 15.3
Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
High-Altitude Operation . . . . . . . . . . . . . . . . . . . . 7.11
Hood Opening and Closing . . . . . . . . . . . . . . . . . . 2.7
L
To Close the Hood . . . . . . . . . . . . . . . . . . . . . . 2.7 Lighting Controls . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
To Open the Hood . . . . . . . . . . . . . . . . . . . . . . 2.7 Control Panels . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Horn Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 Exterior Light Controls . . . . . . . . . . . . . . . . . . . 4.2
Air Horn, Optional . . . . . . . . . . . . . . . . . . . . . . 4.7 Interior Lights and Light
Electric Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Hybrid Electric Vehicle (HEV)
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1
Cooling System . . . . . . . . . . . . . . . . . . . . . . . 15.1
M
Electric Power Take-Off Major Repair and Replacement
(ePTO) . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1 of Natural Gas Components . . . . . . . . . . . . . . . 16.10
High-Voltage Safety Mercedes-Benz Automated
Features . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1 Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . 8.26
I-3
Truck-Manuals.net
Index

AGS Diagnostics . . . . . . . . . . . . . . . . . . . . . . 8.30
General Information, AGS . . . . . . . . . . . . . . . . 8.26
O
Operation, AGS . . . . . . . . . . . . . . . . . . . . . . . 8.26 Other Dash-Mounted Controls . . . . . . . . . . . . . . . 4.14
Mercedes-Benz Manual CB Radio Connections . . . . . . . . . . . . . . . . . . 4.14
Transmissions . . . . . . . . . . . . . . . . . . . . . . . . . 8.25 Cigarette Lighter . . . . . . . . . . . . . . . . . . . . . . 4.14
Meritor WABCO® Antilock Suspension Autofill Override
Braking System . . . . . . . . . . . . . . . . . . . . . . . . . 9.5 Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
Automatic Traction Control . . . . . . . . . . . . . . . . 9.6 Suspension Dump Switch . . . . . . . . . . . . . . . . 4.14
Trailer ABS Compatibility . . . . . . . . . . . . . . . . . . 9.5 Windshield-Fan Switches,
Meritor™ Drive Axles . . . . . . . . . . . . . . . . . . . . . . 8.30 Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.14
Axle Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.33 Overhead Instrument Panel . . . . . . . . . . . . . . . . . 3.13
Drive Axles With Differential
Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.30
Tandem Drive Axles With
P
Interaxle Lock . . . . . . . . . . . . . . . . . . . . . . . 8.32 Power Takeoff (PTO) Governor . . . . . . . . . . . . . . . 7.13
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Powertrain Controls . . . . . . . . . . . . . . . . . . . . . . . 4.7
Down View Mirror, Optional . . . . . . . . . . . . . . . . 5.1 After-Treatment System
Mirror Heat Switch, Optional . . . . . . . . . . . . . . . 5.1 (ATS) Request/Inhibit
Regen Switch . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Power Mirrors, Optional . . . . . . . . . . . . . . . . . . 5.1
Axle Switches . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Monthly Post-Trip Inspection
and Maintenance . . . . . . . . . . . . . . . . . . . . . . 11.13 Cruise Control Switches . . . . . . . . . . . . . . . . . . 4.8
Brake Component Inspection . . . . . . . . . . . . . 11.13 Engine Brake Switch,
Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
Engine Compartment
Inspection and Engine Fan Switch, Optional . . . . . . . . . . . . . . . 4.9
Adjustments . . . . . . . . . . . . . . . . . . . . . . . 11.15 Exhaust Brake Switch,
Natural Gas Fuel System Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Inspection, If Equipped . . . . . . . . . . . . . . . . 11.15 Transmission Controls . . . . . . . . . . . . . . . . . . . 4.9
Saddle Tank Area Pre- and Post-Trip Inspection
Inspections . . . . . . . . . . . . . . . . . . . . . . . . 11.14 Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1
Multifunction Turn Signal Switch . . . . . . . . . . . . . . . 4.5 Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1
Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 4.7 Fluids Added . . . . . . . . . . . . . . . . . . . . . . . . . 11.2
Headlight High Beams . . . . . . . . . . . . . . . . . . . 4.6 Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . 14.1
Turn-Signal Controls . . . . . . . . . . . . . . . . . . . . . 4.5
Windshield Wiper/Washer
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
S
Safety Precautions (HEV) . . . . . . . . . . . . . . . . . . 15.2
N Seat Belts and Tether Belts . . . . . . . . . . . . . . . . . . 5.8
General Information . . . . . . . . . . . . . . . . . . . . . 5.8
Natural Gas Detection System . . . . . . . . . . . . . . . 16.5 Seat Belt Inspection . . . . . . . . . . . . . . . . . . . . . 5.9
Alarm Procedure . . . . . . . . . . . . . . . . . . . . . . 16.5 Seat Belt Operation . . . . . . . . . . . . . . . . . . . . . 5.9
Overhead Console . . . . . . . . . . . . . . . . . . . . . 16.7 Seat Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.6 Bench Seat Adjustment
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.7 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
Natural Gas Engine Starting . . . . . . . . . . . . . . . . . 16.9 Suspension Seat Adjustment
Natural Gas Fuel Tank Filling Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.16
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.2 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
CNG Vehicle Fueling . . . . . . . . . . . . . . . . . . . 16.2 Bench Seats . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4
LNG Vehicle Fueling . . . . . . . . . . . . . . . . . . . . 16.3 Bostrom Seat . . . . . . . . . . . . . . . . . . . . . . . . . 5.5
Natural Gas Vehicles, General Freightliner High-Back Seat . . . . . . . . . . . . . . . . 5.4
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1 General Information . . . . . . . . . . . . . . . . . . . . . 5.2
Natural Gas Vehicles, Safety National 2000 Series Seat . . . . . . . . . . . . . . . . . 5.6
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1 Sears Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7
In Case of Emergency . . . . . . . . . . . . . . . . . . 16.2
I-4
Truck-Manuals.net
Index
Subject Page
Starting After Extended
Shutdown or Oil Change . . . . . . . . . . . . . . . . . . . 7.9
Starting, and Engine Shutdown
(HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2
Engine Shutdown . . . . . . . . . . . . . . . . . . . . . . 15.2
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2
The Cranking System . . . . . . . . . . . . . . . . . . . 15.2
Steering System . . . . . . . . . . . . . . . . . . . . . . . . . 9.1
Steering Wheel Adjustment . . . . . . . . . . . . . . . . 9.1
T
Towing (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5
Front Towing Hookup . . . . . . . . . . . . . . . . . . . 13.5
Rear Towing Hookup . . . . . . . . . . . . . . . . . . . 13.5
V
Velour Upholstery Cleaning . . . . . . . . . . . . . . . . . 12.3
Chewing Gum or Wax . . . . . . . . . . . . . . . . . . . 12.3
Grease and Oil-Based Stains . . . . . . . . . . . . . . 12.3
Mildew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3
Sugar and Water-Based
Stains . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3
Vinyl Upholstery Cleaning . . . . . . . . . . . . . . . . . . 12.2
Ball Point Ink . . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Chewing Gum . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Nail Polish and Nail Polish
Remover . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Ordinary Dirt . . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Paint, Shoe Heel Marks . . . . . . . . . . . . . . . . . 12.2
Shoe Polish . . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Sulfide Stains . . . . . . . . . . . . . . . . . . . . . . . . 12.2
Tars, Asphalts, and Creosote . . . . . . . . . . . . . . 12.2
W
Warning and Indicator Lights . . . . . . . . . . . . . . . . . 3.2
Engine Protection System . . . . . . . . . . . . . . . . . 3.6
Weekly Post-Trip Inspection
and Maintenance . . . . . . . . . . . . . . . . . . . . . . 11.11
Engine Compartment
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . 11.11
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
Windshield Washer Reservoir . . . . . . . . . . . . . . . . 5.11
I-5
Truck-Manuals.net

Freightliner BC M2 Driver Manual PDF

Uploaded by

Freightliner BC M2 Driver Manual PDF

Uploaded by

®

Introduction performed. The EDR is designed to record data re-

Customer Assistance Center

Reporting Safety Defects

Canadian Motor Vehicle Safety

Fig. 1.2, Vehicle Certification Label

Fig. 1.5, Canadian National Safety Mark

See Fig. 1.6 for a typical component GWR label.

Fig. 1.6, Component GWR Label

Applicable Emissions System Based on Build Date and EPA Regulations

the engine after five minutes of idling in order to limit

Certified Clean Idle Label

EXHAUST AFTERTREATMENT SYSTEM INFORMATION

Fig. 1.7, ATS Indicators, EPA07

DEF Refill Needed Diesel Exhaust Fluid (DEF) level is

See operator’s manual for complete instructions. 24−01656−000

Fig. 1.8, ATS Indicators, EPA10 and Newer

VEHICLE NOISE EMISSION CONTROL INFORMATION

Fig. 1.9, Vehicle Noise Emission Control Label CLEAN IDLE

Cab Door Locks and Handles 1 2

IMPORTANT: Each key is numbered. Record

To lock a door from outside the cab, do either one of

Use the cab access system (grab handles, access

Entering from the Driver’s Side

NOTE: The A-pillar grab handle is not installed

NOTE: You can also use the inner door grab

would going down a flight of stairs. It is easier to 1. Bottom Step

2. Grasp the steering wheel with both hands. Place

7. 2. Grasp the A-pillar cover grab handle with both

2. Place one foot on the bottom step and pull your-

Climbing Down from Back-of-Cab

Cab (Battery) Isolation Switch CAUTION

Fuse Identification, Main Fuse Box

These fuse boxes contain mini blade-type fuses, 12-

Instrumentation Control Unit • "Driver Message Center"

If the ICU receives active fault codes, it displays

vehicles may not be equipped with all of the

Common Warning and Indicator Lamps

Indicates the coolant temperature is above the maximum

Indicates air pressure in the primary or secondary reservoir

Indicates the engine oil pressure is below the minimum

Indicates the parking brake is engaged, or hydraulic brake

Parking Brake (EPA10

Activates with an audible alert when the system detects that

Common Warning and Indicator Lamps

Malfunction Indicator Indicates an emissions-related fault. See the engine

Momentary illumination indicates the vehicle ABS is

NO Indicates the alternator is not properly powering the

Indicates the fuel may contain water. Drain any water

Check Transmission Indicates an undesirable transmission condition.

Transmission Overheat Indicates high transmission temperature.

Common Warning and Indicator Lamps

Engine Brake Indicates the engine brake is enabled.

Flashing indicates the outside left-turn signal lights are

Indicates the cruise control is enabled.

Common Warning and Indicator Lamps

High-Beam Headlights Indicates the high-beam headlights are on. Blue

Table 3.1, Common Warning and Indicator Lamps

EXHAUST AFTERTREATMENT SYSTEM INFORMATION

Fig. 3.3, ATS Warning Lamps

On other engines, the engine protection system will i. Odometer

SELECt To Toggle between Units EnG oIL

Fig. 3.6, Manual-Reset Air Restriction Indicator, Go/

Ambient Temperature Gauge

NOTE: Rain or snow can wet the filter and

Coolant Temperature Gauge NOTICE

Minimum Oil Pressure*

Fig. 3.9, Engine Oil Pressure Gauge 10/10/2001 f610569

3 Fig. 3.13, Air Pressure Gauge (reservoir A shown)

gine is off, the voltmeter shows only the isolated bat-

200 275 Overhead Instrument Panel

Turbocharger Boost Pressure Gauge

Ignition Switch and Key WARNING

1. Left-Hand Control Panel

the panel lights, press on the lower part of the rocker

Raise the paddle to flash the marker lights.