Manual - Loading Arm

July 2015
790 Series Counterbalance

Equipment: Torsion Balance Type: 790A,B,C

Balance Unit for balancing Loading Arms
Suitable for: Loading Arm Balancing
• Easy, Precise Adjustment
• No special tools required
Specifications
Right-Hand: 790A-0020 (White),
790B-0030 (Yellow), 790C-0050 (Red)
Type
Left-Hand: 790ALH-0025 (Black),
790BLH-0035 (Gray), 790CLH (Orange)

Working
-40°F to 176°F (-40°C to +80°C)
Temperature Range

Installation NEW: Easy-to-use

Spring Cover Latch
Spring Unit Assembly
1. Position balance unit on the bosses at back of swivel joint.
2. Fix balance unit with Bolts and Lock Washers.
3. Attach backside of Link Arm [17] to Spring Arm [15] with Pin [16] and 2 Retaining
Rings [14].
4. Remove the 4 Socket Head Screws [18] and take Snubber Block [26] off.
5. Raise loading arm to highest position (as vertical as possible).
6. Attach front side of Link Arm [17] to mounting ears on loading arm with Pin [16] and
2 Retaining Rings [14].
7. C
 heck balancing action by pulling down the arm. If adjustment is necessary,
follow adjustment instructions below.
8. Install lock-down unit 788-L, if used, by following 788-L installation instructions.
9. Replace Cover [21] using alignment pins [1] and latches [22].
Adjustment
When to adjust torque
A. To raise loading arm higher or for more lifting action INCREASE torque.
B. To decrease loading arm vertical travel or to slow the rate at which the arm rises,
DECREASE torque.
C. Note: Prior to any disassembly, Spring balance tension should be completely relieved to allow
safe disassembly of level arm.
Torque For more lifting action increase torque. For less lifting action decrease torque.
Place ¾" socket wrench on worm gear hex drive.

To INCREASE torque rotate the worm gear hex drive

counterclockwise (to the left).

To DECREASE torque rotate the worm

gear hex drive clockwise (to the right).

Release wrench and test loading arm

lifting action.

Note: Prior to any loading arm

disassembly, spring tension should be
completely relieved.
Tip: Spring coil will be loose in housing
when completely relieved of tension.
Worm Gear Hex Drive

PHONE: (800) 547-9393 • (513) 696-1500 • Fax: (800) 245-8536 • (513) 932-9845
2726 Henkle Drive • Lebanon, OH 45036 • www.opw-es.com
Manual - Loading Arm
July 2015
790 Series Counterbalance

Parts List: 790 Series Counterbalance

Index Qty Part # Description Index Qty Part # Description

1 4 H-31396-M Spirol Pin, 1⁄4 x 13⁄4 17 1 E-20041-D1 Link Arm, D1
2 1 C-20185-BW Spring Regulator, R.H. Worm Gear 18 4 H-31278-M Socket Head Screw, ZP, .31-18 X 1"
3 1 H-30744-M Dowel Pin .25 x 1.25 19 2 H-02507-M Lockwasher, CP, 5⁄8"
Flange, Bearing, BRZ. 1 ⁄2" DIA x
1
Screw, Hex Cap, CST, ZP, 5⁄8"-11
4 2 H-01490-M 20 2 H-05910-M
11⁄4" LG x 13⁄4"
5 2 H-32283-M Retaining Ring, CST ZP 21 1 E20116P 790 Spring Balance Cover, RH
6 2 H-32282-M Bearing, Cylindrical, Bronze 22 2 H32321M Spring Cover Latch (SouthCo)
7 1 H-30743-M Washer, Thrust, ZP, ⁄8" 7
23 4 H32322M Screw, Thread Forming, 8-32
8 1 C-20184-EW Drive Worm, Torsion Spring 24 1 C-00626-M Spring, Torsion, C
9 2 H-30741-M Screw, Drive #10 x ⁄8" 3
25 1 H-30742-RS Bar, Safety
10 1 H-30740-M Worm Cover Plate, Spring Balance 26 1 H-01489-D1 Snubber Block, RH, D1
11 1 H-30018-M Bolt, ⁄2"-13 x 3 ⁄2
1 1
27 4 H-03563-M Washer, Lock, ZP, 5⁄16"
12 1 H-30049-M Jam Nut, Hex, CST, ZP, 1⁄2"-13 Snubber Retainer, Brass, 11⁄8-12
28 1 H-01486-RB
x 1⁄2"
13 1 E20074D1 790 Support Bracket, D1
Snubber Plunger, SST, 15⁄16" DIA x
14 2 H-30321-M Retaining Ring, CST, 5⁄8" 29 1 H-01487-RE
19⁄16" LG
15 1 D-00350-D1 Spring Arm, PTD, D1
30 1 H-01502-M Spring, Compression, ZP
16 1 H-30320-RE Pin, Torsion Spring, SST 31 1 C00635D1 Support, RH Side, D1

PHONE: (800) 547-9393 • (513) 696-1500 • Fax: (800) 245-8536 • (513) 932-9845
2726 Henkle Drive • Lebanon, OH 45036 • www.opw-es.com
Manual - Loading Arm
July 2015
788, 789, 790 Series Counterbalance

Travel Stop 788, 789, 790 Series

Upward Downward
Remove the (4) socket head screws in snubber block, then rotate Loosen Jam Nut (located below lever arm) and turn
snubber block toward pivot pin to allow for more upward travel or stop bolt in for more downward travel or out for less
away from pivot pin for less upward travel. downward travel. Then hold bolt and tighten jam
Replace the (4) screws and tighten. nut securely.

Pivot Pin
Jam Nut
Stop Bolt

Snubber Block

Adjustment 788, 789 Series

NOTE: Left hand spring balance shown.
NOTE: The worm gear adjustment mechanism provides significant mechanical advantage during adjustment.
Under high load conditions (790) it is recommended that the loading arm be raised to approximately 45° above horizontal.
Under low load conditions it is possible to adjust the spring torque without raising/supporting the loading arm.

For more lifting action increase torque.

For less lifting action decrease torque. 788, 789 Series

1. Raise loading arm to highest position and secure.

2. Hold Adjusting Nut of Spring Regulator [2] with

a large wrench.
Spring Keeper Bolts
3. Loosen lower Bolt of Spring Keeper and remove upper one.
Using a large screwdriver push Spring Keeper forward.
With Spring Keeper disengaged turn Spring Regulator
Adjusting Nut clockwise for more or counter clockwise
for less torque.

4. With spring tension in desired position press Spring Keeper

back into position on Spring Regulator. While holding Spring
Regulator Adjusting Nut, tighten Spring Keeper Bolts [3].
Be sure Lock Washers [4] are in place. 788, 789 Series

5. Minor adjustment can be achieved by turning the Spring

Keeper ½ position. This is done by removing the 2 Keeper
Bolts [3] and turning the Spring Keeper end for end, so that
the “teeth” of the Spring Keeper will be reversed.
Spring Keeper

PHONE: (800) 547-9393 • (513) 696-1500 • Fax: (800) 245-8536 • (513) 932-9845
2726 Henkle Drive • Lebanon, OH 45036 • www.opw-es.com
Manual - Loading Arm
July 2015
788, 789 Series Counterbalance

Parts List: 788, 789 Series Counterbalance

8
3 4 5 6 9

10

No. Part No. Part

1 Torsion Spring 13 Snubber Block
2 1 3 12
2 Spring Regulator 14 Lock Washer

3 Bolt 15 Bolt

4 Lock Washer 16 Bolt

23
5 Spring Keeper 17 Nut
24
6 Spring Arm 18 Screw
15 16
7 Lever 19 Cover (NOT SHOWN) 17
14
8 E-ring 20 Spring Compression 13
3
9 Pin 21 Snubber Retainer 11

10 Support Bracket 22 Snubber Plunger

11 Bearing Flange 23 E-ring

18
12 Side Support 24 Pin
22 21 20 19

Maintenance 788, 789, 790 Series

Lubrication The torsion balance is provided with a self-lubricating Cylindrical Bearing. Only when operating under
severe conditions, a little oil may be applied to Bearing [7]. Pins [13] on Spring Arm [23] and Link Arm [9]
should have some oil quarterly.

Safety
Danger! Before performing any maintenance, always secure the Loading Arm and remove
all tension from the counterbalance -- a torsion spring. The Loading Arm counterbalance
spring contains a substantial amount of stored energy. You must relieve this energy before
any disassembly. Failure to remove all tension from the counterbalance spring of the
Loading Arm before maintenance may cause serious personal injury or death.

WARNING! While installing and using the Loading Arm, always wear adequate personal
protection, including hard hats, gloves, and steel-toed work boots. Failure to wear
adequate personal protection may cause serious personal injury or death.

WARNING! Always follow the procedures prescribed in this Document. Failing to follow
the procedures prescribed may damage the Loading Arm and cause serious personal
injury or death. Consult Loading Arm Installation, Maintenance & Safety Manual for
more details.

PHONE: (800) 547-9393 • (513) 696-1500 • Fax: (800) 245-8536 • (513) 932-9845
2726 Henkle Drive • Lebanon, OH 45036 • www.opw-es.com