Installation, Operation and Maintenance Manual CD, HL & NC Ranges Dri-Prime Pumps

Installation, Operation and Maintenance Manual
CD, HL & NC Ranges
Dri-Prime® Pumps
Pump Serial No.
Manual No. : 95-0019-0000 Issue : 12 Date : - Nov 2011

CD, HL & NC Ranges of Dri-Prime® Pumps
INDEX
1 INTRODUCTION ................................................................................................................................ 3
1.1 Manual Purpose .........................................................................................................................................................3
1.2 Information for the User, Operator or Maintenance Personnel. .................................................................................3
2 WARRANTY....................................................................................................................................... 4
3 HOW TO USE THIS MANUAL .......................................................................................................... 4
4 SAFETY ............................................................................................................................................. 5
4.1 Lifting ..........................................................................................................................................................................5
4.2 General .......................................................................................................................................................................6
5 PUMP SERIAL NUMBER .................................................................................................................. 7
5.1 Spares ........................................................................................................................................................................7
6 INSTALLATION ................................................................................................................................. 7
6.1 Versions......................................................................................................................................................................7
6.1.1 Motor Adaptor .............................................................................................................................................. 7
6.1.2 Bearing Bracket ........................................................................................................................................... 7
6.2 Alignment....................................................................................................................................................................8
6.2.1 Alignment Procedure ................................................................................................................................... 8
6.3 General Installation Notes ..........................................................................................................................................9
7 OPERATION .................................................................................................................................... 10
7.1 General .....................................................................................................................................................................10
7.2 Flooded Suction........................................................................................................................................................10
7.3 Compressor/Vaccum pump disconnection ...............................................................................................................10
7.4 Draining ....................................................................................................................................................................11
8 MAINTENANCE ............................................................................................................................... 12
8.1 Bearings ...................................................................................................................................................................12
8.1.1 Re-greasing procedure .............................................................................................................................. 12
8.2 Seal coolant level .....................................................................................................................................................13
8.3 Seal removal.............................................................................................................................................................14
8.3.1 Front cover & pump body removal ............................................................................................................ 15
8.3.2 Removing the impeller ............................................................................................................................... 16
8.3.3 Removing the rear wear plate ................................................................................................................... 18
8.4 Seal configuration .....................................................................................................................................................18
8.4.1 Removing the seal ..................................................................................................................................... 19
8.4.2 Inspection .................................................................................................................................................. 19
8.5 Seal fitting .................................................................................................................................................................20
8.5.1 Preparation ................................................................................................................................................ 20
8.5.2 Fitting the seal ........................................................................................................................................... 20
8.5.3 Fitting the wear plate ................................................................................................................................. 23
8.5.4 Fitting the impeller ..................................................................................................................................... 24
8.5.5 Front cover & pump body fitting ................................................................................................................. 25
8.5.6 Preparing for service ................................................................................................................................. 25
8.6 Bearing Bracket & Motor Adaptor Dismantling .........................................................................................................26
8.6.1 Preparation for dismantling ........................................................................................................................ 26
8.6.2 Dismantling ................................................................................................................................................ 26
8.7 Bearing Bracket & Motor Adaptor Assembly ............................................................................................................28
8.7.1 Preparation for assembly ........................................................................................................................... 28
8.7.2 Assembly ................................................................................................................................................... 28
8.8 Air Compressor.........................................................................................................................................................32
8.8.1 Filter Replacement .................................................................................................................................... 32
8.9 Vacuum Pump ..........................................................................................................................................................32
8.10 Non Return Valve .....................................................................................................................................................32
8.11 Drive Belts ................................................................................................................................................................32
8.11.1 Timing/HTD Belt Replacement (air compressor) ...................................................................................... 32
8.11.2 Belt Replacement (vacuum pump) ........................................................................................................... 32
8.11.3 Link belt tensioning and replacement ....................................................................................................... 33
9 TOOLS ............................................................................................................................................. 35
9.1 Tool Kits....................................................................................................................................................................35
9.2 Special Tools ............................................................................................................................................................36
10 FAULT FINDING .............................................................................................................................. 36
11 TECHNICAL DATA .......................................................................................................................... 37
11.1 Designations, Sizes & Capacities .............................................................................................................................37
11.1.1 CD range .................................................................................................................................................. 37
11.1.2 HL Range .................................................................................................................................................. 38
11.1.3 NC Range ................................................................................................................................................. 38
11.2 CD Range data .........................................................................................................................................................39
11.3 HL Range data .........................................................................................................................................................40
11.4 NC Range Data ........................................................................................................................................................41
11.5 Spanner Torques ......................................................................................................................................................42
11.6 Thread Locking Compounds ....................................................................................................................................42
11.7 Belt Tensioning .........................................................................................................................................................43
11.7.1 Force and deflection method .................................................................................................................... 43
11.7.2 Belt frequency method .............................................................................................................................. 43
11.7.3 Belt tension figures –HTD/Timing belts .................................................................................................... 43
11.7.4 Belt tension figures Link............................................................................................................................ 43
2 95-0019-0000 Iss 11
1 INTRODUCTION
1.1 Manual Purpose
This manual contains useful and important information to allow the pump to be properly installed, operated and maintained.
It also contains important instructions for preventing possible accidents and serious damage whilst carrying out those
activities.
Carefully read these instructions before commencing any of these activities.
The purpose of this Installation, Operating and Maintenance Manual is to provide the installer, owner or user of the
equipment with sufficient information to carry out those tasks for the CD, HL & NC ranges of Dri-Prime® Pumps.
Pump model designations covered by this manual are: -
CD75 HL80 NC80

CD80D HL100 NC100
CD80M HL110M NC150
CD100M HL125MS
CD103M HL150M
CD140M HL150MHD
CD150M HL200M
CD160M (Mk 1 & 2) HL130M
CD180M HL160M
CD200M HL225M
CD225 HL250M
CD250M HL260M
CD300M
CD400M
CD500M
The information contained in this manual was correct at the time of publication. It is subject to amendment at any time.
Should any doubt exist about the veracity of the information, contact Godwin Pumps Ltd for clarification before proceeding.
The pump may be supplied as a bare shaft pump end or packaged with a driver into a pump set. This manual covers the
pump end only. For packaged pump sets, information on equipment other than the pump end is contained in separate
documentation.
1.2 Information for the User, Operator or Maintenance Personnel.

Installation and maintenance is designed to be carried out using simple hand and service tools. A range of special tools
designed to ease dismantling and reassembly is available from Godwin Pumps Ltd. When the user has insufficient tools,
experience or ability, this work should not be attempted. Under no circumstances should makeshift tools or equipment be
used, as this may adversely affect safe working practices and pump operation.
Because of the number of different units covered by this manual, the user must ensure that they are reading the correct
instructions and viewing the correct diagrams for the unit they are working on.
Ensure that suitably qualified personnel carry out the installation. The variety of conditions and environments in which this
equipment can be used means that the operator and those responsible must satisfy themselves as to the safety and
acceptability of each application and operating condition of this equipment. Standard pumps are designed for use with
predominately clean or dirty water. For all other applications, including sea water, consult Godwin Pumps Ltd. Under no
circumstances will Godwin Pumps Ltd be responsible or liable for indirect or consequential damages arising from the use or
application of this equipment.
Parts that have not been approved by Godwin Pumps Ltd cannot be relied upon for correct material, dimensions or finish.
Godwin Pumps Ltd cannot therefore be held responsible for any damage arising from the use of such parts. This and failure
to observe any instruction or procedure in this manual will invalidate the warranty.
95-0019-0000 Iss 11 3
2 WARRANTY
Unless special arrangements have been agreed and signed by both parties Godwin Pumps Ltd. will apply the following
policy over defects found after delivery.
We will make good, by repair or the supply of a replacement, defects which, under proper use, appear in the goods within a
period of twelve calendar months after the goods have been delivered (1) and arise solely from faulty design (other than a
design made, furnished or specified by you for which we have disclaimed responsibility in writing), materials or
workmanship: provided always that defective parts have been returned to us if we shall have so required. We shall refund
the cost of carriage on such returned parts and the repaired or new parts will be delivered by us free of charge.
Our liability under this clause shall be in lieu of any warranty or condition implied by law as to the quality or fitness for any
particular purpose of the goods, and save as provided in this clause we shall not be under any liability, whether in contract,
tort or otherwise, in respect of defects in goods delivered or for any injury (2), damage or loss resulting from such defects as
from any work done in connection therewith.
(1) For export orders, within a period of twelve calendar months after the goods have been delivered or, if delivery is
delayed by reason of customer instructions or lack of instructions, within a period of 18 months after the goods have
been notified as ready for despatch (whichever period expires the earlier).
(2) For UK orders, other than personal injury caused by our negligence as defined in Section 1 of the Unfair Contract
Terms Act, 1977.
3 HOW TO USE THIS MANUAL

Read this section before installing, operating or carrying out any maintenance on the unit.
When the pump is being installed operated or maintained there are a number of practices that may lead to personal injury or
product damage. Your attention is drawn to the following symbols and their meaning used throughout this manual.
used to identify mechanical hazards
used to identify electrical hazards
CAUTION
This caution symbol draws attention to special instructions or procedures which, if not correctly followed,
may result in damage to, or destruction of equipment.
WARNING
This warning symbol draws attention to special instructions or procedures which, if not strictly observed,
may result in personal injury.
WARNING
A WARNING SYMBOL WITH THIS TYPE OF TEXT DRAWS ATTENTION TO SPECIAL INSTRUCTIONS
OR PROCEDURES WHICH, IF NOT STRICTLY OBSERVED, MAY RESULT IN SEVERE PERSONAL
INJURY, OR LOSS OF LIFE.
NOTE: - A note is used to draw your attention to additional important information.
4 95-0019-0000 Iss 11
4 SAFETY
WARNING
ALL ITEMS IN THIS SECTION, IF NOT STRICTLY OBSERVED, COULD RESULT IN SEVERE
PERSONAL INJURY OR LOSS OF LIFE.
4.1 Lifting
Use only lifting equipment of suitable capacity for the size and weight of the equipment being lifted
The equipment must always be lifted using safe working practices and in accordance with any local and national guidelines
or statutes. Figure 1, Figure 2, Figure 3 and Figure 4 show possible means of lifting. They are intended for guidance only. If
in doubt, consult Godwin Pumps Ltd or a local lifting expert.
CD225_02
HL100-04
CD100_02
HL100-02
Figure 1 Lifting smaller motor adaptor units Figure 2 Lifting smaller bearing bracket units
Figure 3 Typical lifting methods for close coupled bare shaft units (CD300M shown)
CD400 LIFT
Figure 4 Typical lifting method for CD400 pumps
Whilst lifting the unit keep personnel well away and never allow people underneath.
95-0019-0000 Iss 11 5
4.2 General
Personnel working on the pump must always wear clean, correctly fitting clothing and safety footwear. Clothing impregnated
with oil or fuel can constitute a health hazard through prolonged contact with the skin and may also constitute a fire hazard.
Signs on the unit (e.g. directional arrows, maintenance and serial number plates & fluid connections, etc.) must be kept
clean and clear.
Check the type of liquid that the pump has been used for before carrying out any maintenance work. Residues could be
hazardous to your health. If in doubt, flush thoroughly with clean water before commencing work.
Rotating equipment presents a hazard in itself. Alert surrounding personnel before starting and post notifications whilst in
operation.
Moving parts are guarded to protect you. Guards removed for maintenance must be replaced before starting the pump.
Never insert anything into the pump body whilst the pump is running and the suction or delivery hoses are disconnected.
Use all flange bolt holes and ensure the correct bolt size and quality is utilised when connecting suction and delivery hoses.
Collapsible hoses must never be used on the suction side of the pump.
Keep the hose end suction area free from debris. Although the pump can handle solids up to the size indicated in the
Technical Data section of this manual, larger or irregular solids may cause blockage with damage to pump components.
Always allow adequate ventilation for the pump driver. Diesel engines require air for both combustion and cooling. Electric
motors require air for cooling purposes. This air must never be allowed to re-circulate.
Be aware of burn and fire risks from items such as exhaust pipes and silencers. Never place flammable items around the
unit.
Diesel engine exhaust and some of its constituents are known in the State of California to cause cancer, birth defects and
other reproductive harm.
Liquid pressure may still be present even after shutdown of the pump. Particular attention should be paid to delivery lines
that are long, or rise through any height, as these can contain large volumes of liquid. These lines must be isolated and
drained down before commencing work. Sudden release of this liquid can cause serious injury to an operator either directly
or indirectly through the rotational motion it can induce.
6 95-0019-0000 Iss 11
5 PUMP SERIAL NUMBER

Every pump unit has a nameplate similar to one of those shown below. This nameplate lists the serial number and type of
the pump. These numbers must be quoted in any enquiry for spares or service.
Figure 5 Typical pump serial number plates
5.1 Spares
Use only genuine parts from your local Godwin Pumps Ltd supplier or distributor. Failure to do so may invalidate warranty
and/or reduce the pump’s working life.
6 INSTALLATION
All pumps in the range are designed to be run in one direction only. This is anti-clockwise when viewed from the suction
flange end or clockwise when viewed from the driving shaft end.
Rotation on electric motor driven pumps should be checked carefully – preferably with the coupling disconnected. On
installations where coupling disconnection is not possible apply power only for a brief instance, preferably with a soft start, in
order to determine rotation. A fast start or prolonged running in the wrong direction could cause parts to come loose.
CAUTION.
Failure to provide the correct rotation will give rise to poor performance, vibration and possible severe
damage to the pump.
6.1 Versions
Larger pumps (CD300/400/500 or HL130/160/225/250/260) can be supplied with or without an SAE adaptor fitted. With the
adaptor fitted they are suitable for direct coupling, without they are suitable for open coupling. The bearing bracket must be
adequately supported when used as open coupled units. If any doubt exists over the suitability of the support consult
Godwin Pumps Ltd.
Smaller pumps in the range are supplied as either motor adaptor or bearing bracket versions: -
6.1.1 Motor Adaptor

Motor adaptor (MA) versions of the pump are designed for close coupling to a suitable driver, usually a diesel engine. They
are supplied with transport feet that must be removed before attachment to the driver. Alignment of the pump to driver will
be taken care of by the flanged adaptor.
6.1.2 Bearing Bracket

Bearing bracket (BB) versions of the pump are designed for open coupling with the bearing bracket supported from the
same base but standing independently of the driver.
Correct alignment is critical for the longevity of the pump bearings, coupling and driver bearings. Follow the coupling
manufacturers’ instructions exactly.
See Section 6.2 for recommendations on alignment.
95-0019-0000 Iss 11 7
6.2 Alignment
The following notes provide general guidance on alignment and its elimination.
It is normal practice to carry out any adjustment to alignment by moving the driver – not the pump. In designing any
structure to support the pump set allow an additional 0.25mm (0.010”) extra height difference between pump and driver
support for shimming purposes.
There are two forms of misalignment – parallel and angular. Both must be less than the coupling manufacturers’ guidelines
in order for the coupling and bearings to give long and trouble free operation.
It is essential that the baseplate or support structure be fully tightened down before commencing any alignment procedures.
This will ensure that no misalignment is introduced by support structure deformation.
Alignment must always be carried out before any pipework is attached to the pump. Keep a note of the actual figures. Carry
out a check after the pipework has been attached and compare the figures. Any discrepancy must have been introduced by
the pipework attachment and must be corrected by refitting the pipework before putting the pump into service.
CAUTION.
Incorrect coupling alignment will lead to premature bearing and /or coupling failure.
6.2.1 Alignment Procedure

Roughly align the pump and driver by eye.
a) Parallel alignment
Mount a dial gauge on the driver shaft with the gauge running on the outer-machined Pump Driver
diameter of the pump coupling (see Figure 6). If the driver shaft is not accessible then the dial
gauge can be mounted on the driver coupling.
Turn the driver shaft, note the total indicator reading, and adjust the driver position
accordingly. Recheck.
Parallel alignment.wmf
Figure 6 Initial parallel alignment check
b) Angular alignment
Mount the dial gauge on the driver shaft or coupling (as for step a)) and adjust the dial Pump Driver
gauge to run on a mating face of the coupling as close to the outer diameter as
possible (see Figure 7).
Turn the driver shaft, note the total indicator reading, and adjust the driver in the
direction required. Recheck.
Angular alignment.wmf
Figure 7 Angular alignment check
c) Confirming parallel alignment

Mount a dial gauge on the pump shaft with the gauge running on the outer-machined
diameter of the driver coupling (see Figure 8). If the pump shaft is not accessible then Pump Driver
the dial gauge can be mounted on the pump coupling provided the mounting face is
concentric with the shaft.
Turn the pump shaft and note the total indicator reading. Adjust the driver in the
direction required and recheck.
Parallel alignment 1 .wmf
Figure 8 Secondary parallel alignment check
After alignment the pump and driver should be fully tightened down and the alignment rechecked to ensure that nothing has
moved in the tightening down procedure.
If a dial gauge is not available, then vernier callipers (or a taper gauge) and a straight edge can be used, providing the
coupling is of a type that permits it.
Measure the gap between coupling faces with the vernier callipers (or taper gauge) at four points equidistant around the
circumference of the coupling. Adjust until all are equal.
Use a straight edge across both machined outer diameters of the coupling at four points equidistant around the
circumference to confirm parallel alignment.
8 95-0019-0000 Iss 11
6.3 General Installation Notes
Godwin Pumps Ltd. may refute warranty liability if the installation does not meet the requirements of the pump. Should any
doubt exist as to the suitability of an installation, then Godwin Pumps Ltd. should be consulted.
Only suitably qualified personnel (both mechanical and electrical) should carry out the installation. All local and national
regulations in force must be observed.
The coupling used to connect the driver and pump must have the correct characteristics for the purpose. If in doubt –consult
Godwin Pumps Ltd.
The completed pump set must be mounted on a firm level surface.
On bare shaft pumps guarding of the belts, pulleys and couplings is the responsibility of the installer.
Pump sets are supplied with guarding to meet general applicable standards but site conditions may necessitate further
measures such as railings or screens. These are also the responsibility of the installer.
The Godwin Dri-Prime pump range is designed to operate on long lengths of suction pipe but it is always advisable to
position the pump as close to the source as possible.
The Godwin Dri-Prime product is designed to handle small amounts of air leakage, but to ensure optimum pump
performance, it is advisable to ensure that the suction pipe work is airtight and the end is sufficiently submerged to prevent
air being drawn into the pipe.
A general-purpose strainer should be fitted to the end of the suction pipe work and the total area of the openings should be
at least three times the normal area of the suction pipe work. Strainer apertures should be no greater than the maximum
recommended solids handling size for the pump.
The suction and delivery pipe work should be kept as short as possible with a minimum number of large radii bends to
minimise pipe friction losses. To maximise flow rates, it is encouraged to fit larger diameter pipe work than the pump
connection sizes.
Lay out piping runs before connecting to the pump to ensure that tight bends and other flow restrictions are not included.
Figure 9 shows some common pipeline installation problems and their recommended solutions.
Figure 9 Common pipeline installation problems and their solutions
Hose line recommendations
It is important that the suction and delivery pipe work is supported immediately after the pump connections to prevent
straining and possible misalignment of the equipment.
95-0019-0000 Iss 11 9
7 OPERATION
7.1 General
Before attempting to start the unit ensure that you are familiar with the controls and any local or national safety regulations.
If the unit is engine driven refer to the engine manufacturer’s manual.
If the unit is driven by an electric motor refer to the relevant control requirements.
Once the unit is started, the air compressor or vacuum pump will start to prime the pump and the unit will require no further
attention.
7.2 Flooded Suction

Should the unit be required to operate under flooded suction conditions (i.e. liquid to be pumped is above pump suction
connection – see Figure 10), then the air compressor or vacuum pump pipeline to the pump must be disconnected and the
pump opening blocked. The compressor or vacuum pump drive must also be disconnected to save wear on the compressor
or vacuum pump.
CAUTION.
Failure to disconnect the pipeline will result in serious compressor or vacuum pump damage and
consequential pump failure.
Disconnect
compressor
drive
Disconnect
vacuum pump
Remove priming tower drive Remove ejector
complete and replace package and
with blanking plate
blank off
HL100-05
Figure 10 Flooded suction conditions

The duty of the pump should be carefully checked against the drive characteristics. In some instances this arrangement can
overload the driver.
7.3 Compressor/Vaccum pump disconnection

WARNING.
This procedure requires access to operating and rotational parts of the pump. Accidental start up could
cause injury.
To disconnect: -
a) Ensure that the driver is isolated and the unit cannot be started whilst the pump is being worked on.
b) Compressor units: -Disconnect the air delivery pipe to the ejector.
Vacuum pump units: - Disconnect the air suction pipe from the priming tower.
Compressor units: -Remove the ejector housing complete and replace with a plain blanking plate (see
c) Figure 11).
Vacuum pump units: -Remove the priming tower complete and replace with a plain
blanking plate.
Blanking plates are available from Godwin Pumps Ltd or may be fabricated on site.
d) Ensure that the blanking plate has a leak free joint to the pump
e) Remove the isolation means from the driver and restart the pump.
HL100_09
Figure 11 Typical blanking plate fitted in place of ejector housing
Remove the blanking plate, replace the ejector housing or priming tower, reconnect the air hose and reinstall the
compressor/vacuum pump drive when the pump is next required to self-prime.
10 95-0019-0000 Iss 11
7.4 Draining
In cold weather when the slightest possibility of frost exists, drain the pump and the non return valve (if fitted). The drain
plug is either on the bottom or side of the volute (see Figure 12), or on the underside of the discharge flange (see
Figure 13).
CAUTION.
Failure to drain the pump and non return valve in these conditions could result in the pumped product
residue freezing and cracking the volute or non return valve.
Side/bottom drain if
volute is turned for
vertical discharge
Discharge flange drain
Figure 12 Side/bottom drain plug position

Figure 13 Discharge flange drain plug position
95-0019-0000 Iss 11 11
8 MAINTENANCE
8.1 Bearings
All CD, HL & NC range pump shafts are supported from two bearing positions. The types of bearings and configurations
vary across the ranges.
8.1.1 Re-greasing procedure

Grease specification and greasing interval: - Check every 250 hours and recharge if necessary. Do not overgrease. See
Technical Data section for grease types.
Grease nipple positions: - See Figure 14
Clean both the grease nipple and the grease gun nozzle thoroughly before application. Two or three strokes of a hand held
grease gun per grease nipple are sufficient. Overfilling the bearings with grease can be as harmful as under lubrication.
Compaction of grease results in it being churned by the rolling action of the bearings which leads to overheating, breakdown
of the lubricant and ultimately bearing failure.
CAUTION.
Failure to re-grease the bearings correctly with the correct type of grease at suitable intervals could result in
premature bearing failure.
Remove any excess grease from the unit, particularly in the area of any drive belt. Grease on the drive belt will shorten its
life and lead to premature failure.
Pump
Adaptor Pump
CD100-03
CD80-05
HL100-07
Grease nipple
accessed through
adaptor
Grease
relief
valves
Pump
body
Adaptor
Pump
Adaptor
HL200-01
CD80-02 CD225-03
Grease
nipples
Adaptor
Pump
HL250-04
Figure 14 Grease nipple positions
12 95-0019-0000 Iss 11
8.2 Seal coolant level
All pumps are fitted with mechanical seals cooled by either oil or a glycol mixture. The HL260M & CD500M are glycol
cooled, all others use oil. Seal types and configurations vary across the ranges. Check the coolant level in the seal housing
at least once a week – preferably daily.
Please not the seal oil may become emulsified after a short period of operation, this is normal and not cause for concern.
The extent and timing depends on the conditions under which the pump is operated. This is not detrimental to the operation
of the seal, but the oil must be changed at the first sign of sludging.
Coolant level can vary depending on the conditions under which the pump is operated. A slight loss of coolant under high
suction lift conditions or slight emulsification of oil under low conditions is normal.
Oil and glycol specifications: - see Technical Data section
CAUTION.
Dry running caused by failure to initially fill, subsequently maintain the correct coolant level, or use the wrong
coolant in the seal housing will result in seal failure.
Seals that have failed due to lack of operator provision of the correct and sufficient coolant are not covered by the warranty.
The various configurations for filling and draining are shown in Figure 15, Figure 16 or Figure 17.
Fill
Fill
Pump
body
The seal coolant level for pumps of the style Pump
shown in Figure 15 is 10 –15mm below the
bottom of the plug. If no coolant is visible
Adaptor
then it must be topped up before starting the
pump.
CD80-06
CD80-03
Drain
Drain
Figure 15 Smaller pump fill and drain plugs

Fill
Pump Fill
Adaptor
Adaptor
The seal coolant level for pumps of the style Pump
shown in Figure 16 is 35-40mm below the
filler plug seating face (10 –15mm below the Drain
(diametrically
bottom of the filling hole) opposite to fill)
CD225-04
Drain
CD100-04
Figure 16 Medium sized pump fill and drain plugs

Dipstick
and Fill
Adaptor
Larger pumps (Figure 17) have a filler plug
combined with a dipstick. The coolant level Pump
must be maintained between the maximum
and minimum marks.
HL250-03
Drain
Figure 17 Larger pump fill and drain plugs
95-0019-0000 Iss 11 13
8.3 Seal removal
WARNING.
This procedure requires access to operating and rotational parts of the pump. Accidental start up could
cause injury.
1) Isolate the driver and ensure the unit cannot be started whilst the pump is being worked on.
2) Drain down the delivery line (see warning note in Section 4). Disconnect both suction and delivery lines. Ensure that
the non-return valve is empty.
3) Drain water from the pump (see Section 7.4).
4) Drain the coolant oil from the mechanical seal cavity (see Section 8.2).
5) For units fitted with a compressor disconnect the air supply hose to the ejector head. For units fitted with a vacuum
pump disconnect the suction hose from the priming tower.
WARNING.
Dismantling requires adequate support of both the parts being removed and the remaining parts of the
pump. Those being removed must be supported by suitable lifting gear whilst fasteners are undone. The
lifting gear can then be used to lift the part clear. Remaining parts must also be adequately supported.
Failure to hold or support the parts adequately could cause them to fall and cause injury.
14 95-0019-0000 Iss 11
8.3.1 Front cover & pump body removal

Pump types CD75 / CD80D / CD80M / CD100M
The pump body and front cover are one piece. They are fitted with studs that pass through the adaptor or bearing bracket,
secured by nuts and spring washers. Undo and remove the nuts and spring washers (see Figure 18 or Figure 19). Remove
the pump body complete with non-return valve and ejector package (if fitted) to expose the impeller.
Pump
body
Adaptor
CD80-07
CD80-04
Figure 18 Typical pump body attachment to bearing Figure 19 CD75 & CD80D Pump body attachment to motor
bracket (CD80D shown) adaptor
Pump types CD103M/ CD140M/ CD150M CD160M (Mk 1 & 2)/ CD180M/ CD225/ CD200M/ CD300M/ CD400M/
CD500M
HL80/ HL100/ HL110M/ HL125MS/ HL150M/ HL150MHD/ HL200M/ HL130M/ HL160M/ HL225M/
HL250M/ HL260M
NC80/ NC100/ NC150
Due to the weight and size of the parts on these larger pumps and lifting gear limitations it is recommended that items such
as separation tanks, priming towers and non return valves are removed before proceeding further.
Release and remove the fasteners holding the front cover to the pump body (see Figure 20). These are on the periphery of
the front cover. At this stage do not disturb any other fasteners, as these hold the front wearplate to the front cover. Remove
the front cover and wearplate complete. Larger pumps are provided with pre-tapped holes around the periphery to enable
the use of jacking screws to help in removal.
NOTE: - The CD400M and CD500M have an adaptor plate fitted between the front cover and pump body. It carries the
front wearplate and is located by a spigot on the front cover. It normally detaches with the front cover, but may occasionally
require separate removal.
Jacking
Screws
Figure 20 Removal of front cover

Larger pumps (HL80, CD180M, CD300M, CD400M, CD500M, HL160M, HL225M, HL250M and HL260M) have bodies with
sufficient room to allow the seal to be removed without further dismantling. For other units and the HL130M, release and
remove the peripheral fasteners holding the pump body to the adaptor.
Arrange a suitable support to take the weight once the pump body is removed. Release and remove the bolts holding the
pump body down.
CAUTION.
Failure to support the motor adaptor once the pump body is removed could distort the adaptor and displace
the bearings leading to pump failure.
Remove the pump body to expose the impeller.
95-0019-0000 Iss 11 15
8.3.2 Removing the impeller
Lock the pump shaft to prevent rotation. Tools are available from Godwin Pumps Ltd for this purpose. See Section 9.
WARNING.
Failure to lock the pump shaft could lead to unexpected rotation of the impeller causing entrapment and the
possibility of serious injury.
Pump types CD75/ CD80D/ CD80M

The impeller is screwed (right hand thread) directly onto the shaft. Unscrew in anti clockwise direction.
If the impeller is reluctant to rotate, place a block of wood against one of the vanes and tap lightly with a hammer to
overcome the initial resistance.
Shims will have been fitted on the shaft behind the impeller. Remove these carefully and retain for reuse unless damaged.
Pump types CD100M/ CD103M/ CD140M/ CD150M/ CD160M (Mk 1 & 2)/ CD180M/ CD200M/ CD225/ CD250M
HL80/ HL100/ HL110M/ HL125MS/ HL50M/ HL150MHD/ HL200M
The impeller is screwed (right hand thread) directly onto the shaft and retained by a screw in the centre of the boss. Remove
the screw. (NOTE: - this screw incorporates a self locking device and must be replaced and not reused). Unscrew the
impeller in an anti clockwise direction.
If the impeller is reluctant to rotate, place a block of wood against one of the vanes and tap lightly with a hammer to
overcome the initial resistance.
Shims will have been fitted on the shaft behind the impeller. Remove these carefully and retain for reuse unless damaged.
Pump types NC80/ NC100/ NC150

These sizes of N pump all utilize a tapered locking sleeve
incorporating a left hand threaded adjustment screw. The
impeller is locked in place with a cap head screw and washer.
The following diagrams show an NC80 pump but the
instructions apply to all.
The impeller retaining fittings are shown in Figure 21
Remove one of the access plugs around the periphery of the
volute. Insert a suitable bar to prevent the impeller from
rotating. Ensure the bar is of a suitable material or is wrapped
so that the threads in the hole are not damaged when the bar
presses against them.
Unscrew the central retaining socket head cap screw, remove
it and the washer.
Figure 21 Impeller retaining fittings
Insert a 65mm long 12 A/F hexagon socket bit

through the central hole of the impeller and
locate it in the hexagon of the adjustment
screw.
Using hexagon socket bit turn the adjustment
screw slowly anti-clockwise until the contact
between the impeller and the locking sleeve is
broken. Remove the impeller
Figure 22 X-section showing the taper sleeve and adjustment screw
16 95-0019-0000 Iss 11
Pump types CD300M/ CD400M/ CD500M

HL130M/ HL160M/ HL225M/ HL250M/ HL260M
The impeller retaining fittings are shown in Figure 23
Unscrew the cover in the centre of the impeller and
expose the impeller locking bolt.
Knock down the tabs on the tab washer. Unscrew the
bolt. Remove the bolt, tab washer and clamping
washer.
The impeller is splined on to the shaft and can now
be pulled off.
Shims will have been fitted on the shaft behind the
impeller. Remove these carefully and retain for reuse
unless damaged. Some units will have a shaped
impeller spacer fitted behind the shims. Remove and
retain for reuse.
Figure 23 Impeller Retaining fittings
95-0019-0000 Iss 11 17
8.3.3 Removing the rear wear plate

Fasteners from the motor adaptor/bearing bracket/seal housing adaptor side retain the rear wear plate. Undo these
fasteners and remove the wear plate. Larger pumps are provided with pre-tapped holes to enable the use of jacking screws
to help in removal.
Pump types CD75/ CD80D/ CD80M/ CD100M/ CD103M/ CD150M

HL80
NC80/ NC100/ NC150
The rear wear plate holds the seal seat retained by a circlip (item 6 in Figure 24). Once the wear plate has been removed
the remainder of the mechanical seal is left exposed on the shaft.
Remove the circlip from the wear plate and press out the seal seat.
Pump types CD140M/ CD160M (Mk 1 & 2)/ CD180M/ CD200M/ CD225/ CD250M/ CD300M/ CD400M
HL100/ HL110M/ HL125MS/ HL150M/ HL150MHD/ HL200M/ HL130M/ HL160M/ HL225M/ HL250M
Removal of the wear plate exposes the outer seal seat carrier retained by four off cap head socket screws. Removing the
screws and carrier exposes the remainder of the mechanical seal on the shaft. The inside face of the seal carrier holds the
outer seal seat (item 12 in Figure 25 or Figure 26, item 1 in Figure 27) retained by a clamping ring held in place by screws.
Remove the screws from the clamping ring. Remove the clamping ring and press out the outer seal seat.
Pump types CD500M

HL260M
The rear wear plate carries the outer seal seat directly on its inner face. Take care in removing the wear plate to avoid
damaging the seat on the shaft. The seal seat is retained on the back of the wear plate a clamping ring held in place by
screws.
Remove the screws from the clamping ring. Remove the clamping ring and press out the outer seal seat. Later models
incorporate a roll pin which protrudes from the back of the wearplate into a groove on the inner seat face. This is an
additional device to stop the inner seal seat from rotating.
8.4 Seal configuration

Identify the correct seal configuration from the following table. Follow the relevant instructions for dismantling and
reassembly. Note that although the arrangement type may be the same, size and individual detail between pumps will be
different.
Type Pump type Seal configuration Remarks
CD75
CD80D
CD80M HL80
Single mechanical seal inboard
CD100M HL100M NC80
isolating the pumped product
1 CD103M HL125MS NC100
Dynamic lip seal outboard retaining
CD140M HL150M NC150
the oil
CD150M HL150MHD
CD200M
CD225M
CD160M Mk1 HL130M Open coupled versions of
2 off mechanical seals fitted back to
2 CD180M HL160M CD300M only.
back (double mechanical seal)
CD300M HL250M Earlier versions of HL130M.
CD160M Mk2 HL110M 2 off mechanical seals fitted back to Similar arrangement to type 2
3
CD400M HL200M back (double mechanical seal) but differently configured
Fitted to later versions of
HL130M
CD300M 2 off mechanical seals fitted back to these pumps that share a
HL225M
4 back in a cartridge (double one piece common bearing bracket.
mechanical seal) Fitted as standard from first
CD500M HL260M
off.
18 95-0019-0000 Iss 11
8.4.1 Removing the seal

Pump types CD75/ CD80D/ CD80M/ CD100M/ CD103M/ CD140M/ CD150M/ CD200M/ CD225/ CD250M
HL80/ HL100M/ HL125MS/ HL150M/ HL150MHD
(Figure 24)
NC80/ NC100/ NC150
6 1 2 3 4 5
Remove the rotating seal face (1) and O-ring (2) from the shaft.
Unscrew the grub screws (5) holding the stationary seat (3) to the shaft. Remove the
stationary seat.
CD140M, CD200M, CD225M, CD250M, HL100M, HL125MS, HL150M & HL150MHD
have a spacer fitted on the shaft behind the mechanical seal. This will now be loose.
Remove the spacer and retain for reuse.
Figure 24 Type 1 single mechanical seal Ø40 mechanical seal
Lapped
seal faces
Pump types CD160M Mk 2/ CD180M/ CD300M
(Figure 25) HL130M/ HL160M/ HL250M
12 1 2 3 4 5 13 11
Remove the rotating seal face (1) and O-ring (2) from the shaft.
Unscrew the grub screws (5) holding the stationary seat (3) to the
shaft. Remove the stationary seat.
Remove the second rotating seal face (13).
The seal seat (11) is held in a carrier retained by 4 off cap head
socket screws. Undo the screws, remove the carrier and seat.
Press the seat out of the carrier.
Figure 25 Type 2 two part double mechanical seal
Lapped Lapped
seal faces seal faces
Pump types CD160M Mk 1/ CD400M
(Figure 26) HL110M/ HL200M
12 1 2 3 4 5 6 7 8 9 10 11
Remove the rotating seal face (1) and O-ring (2) from the
shaft.
Unscrew the grub screws (5) holding the stationary seat (3)
to the shaft. Remove the stationary seat.
Unscrew the grub screws (6) holding the second stationary
seat (8) to the shaft. Remove the stationary seat.
Figure 26 Type 3 double mechanical seal
Ø90double mechanical seal
Remove the second rotating seal face (10) and O-ring (9) Lapped Lapped
from the shaft. seal faces seal faces
The seal seat (11) is held in a carrier retained by 4 off cap head socket screws. Undo the screws, remove the carrier and
seat. Press the seat out of the carrier.
Pump types CD300M/ CD500M

Extract the sleeve (2) carrying the double seal faces.
The seal seat (11) is held in a carrier retained by 4 off cap head socket screws.
Undo the screws, remove the carrier and seat. Press the seat out of the carrier.
The seal seat (3) is held in a carrier retained by 4 off cap head socket screws.
Undo the screws, remove the carrier and seat. Press the seat out of the carrier.
Figure 27 Type 4 one piece double mechanical seal
8.4.2 Inspection
Inspect all items for wear. The seal face for type 1, 2 & 3 seals (item 6 in Figure 24; item
12 in Figure 25 or Figure 26) is double sided. It may be reversed when refitted to provide
a second wearing face. Replace any damaged parts and renew all O-rings.
95-0019-0000 Iss 11 19
8.5 Seal fitting
CAUTION.
Mechanical Seals are precision engineered devices. Extreme care must be taken to ensure that no damage
occurs to the lapped faces. These faces must be kept absolutely clean throughout the entire installation. Do
not touch them or allow any contaminant to come into contact with them. Soiled faces will have to be
cleaned with appropriate alcohol based degreasing cleaner and soft tissue. Failure to observe these
precautions will lead to premature seal failure.
8.5.1 Preparation
Ensure that the parts and edges the seal will pass over or through during the assembly process are free from any burrs or
sharp edges and are scrupulously clean. Any of these could damage the seal during assembly and cause premature failure.
Clean the shaft thoroughly and lubricate with clean water or a diluted soft soap solution. Do not use heavy grease, silicone
or PTFE based lubricants, as these would prevent the seal bellows from gripping the shaft.
It is recommended that the seal components be laid out in the order of assembly before starting to enable easy identification
during the procedure.
The retaining screws for the seal shaft sleeve should be fitted using a thread locking compound. See Technical Data section
for details.
8.5.2 Fitting the seal
Pump types CD75/ CD80D/ CD80M/ CD100M/ CD103M/ CD140M/ CD150M/ CD200M/ CD225/ CD250M
HL80/ HL100M/ HL125MS/ HL150M/ HL150MHD
(Figure 24)
NC80/ NC100/ NC150
CD140M, CD200M, CD225M, CD250M, HL100M, HL125MS, HL150M & HL150MHD only. Fit the seal spacer onto the
shaft ensuring it seats against the shaft shoulder.
Carefully remove the rotary head (1) and O-ring (2) from the assembly. Do not place the rotary head (1) face down as this
may cause damage to the lapped seal face.
Take the sleeve assembly (3) and ensure that the drive screws (4) are fully retracted to prevent scratching of the shaft
during assembly. Carefully slide the sleeve assembly along the shaft until it butts up against the shaft shoulder (CD75 &
CD80D), collar (CD80M, CD100M, CD103M, CD150M) or spacer (CD140M, CD200M, CD225 CD250M, HL100M,
HL125MS, HL150M & HL150MHD).
Apply thread locking compound (see Technical Data Section) and lightly tighten the drive screws to centralise the sleeve on
the shaft. Ensure that the sleeve is still abutted to the shoulder, collar or spacer, and then tighten the drive screws fully.
Lightly smear the O-ring (2) with a silicon based grease lubricant. Place the O-ring inside the rotary head (1). Avoid getting
any grease onto the lapped seal face.
Gently push the rotary head (1) onto the sleeve assembly (3) ensuring that the drive pins (5) are engaged in the slots of the
rotary head.
Carefully clean the lapped seal face with a suitable degreasing agent and soft tissue.
Fit the seal seat (6) to the wear plate and retain with either the circlip or retaining clamp. Ensure a new O-ring is fitted.
20 95-0019-0000 Iss 11
Pump types CD160M Mk 2/ CD180M/ CD300M

Take the seal seat (11) from the inboard assembly, lightly smear the O-ring with silicon based grease lubricant and carefully
push into the seat carrier.
Fit a new O-ring to the carrier and slide the assembly along the shaft to seat in the adaptor. Secure with cap head screws
and washers.
If necessary, carefully clean the seal seat (11) and seal face on the rotary head (13) with a suitable degreasing agent and
soft tissue.
Ensure that the grub screws (5) in the mechanical seal (3) are fully retracted so that they do not scratch the shaft during
assembly.
Carefully remove the rotary head (1) and O-ring (2) from the assembly. Do not place rotary head face down as this may
cause damage to the lapped seal face.
Take the mechanical seal (3), locate the spring in the face seal (13) and carefully slide the two along the shaft until the faces
touch.
Set the seal working length, apply thread locking compound (see Technical Data Section) and lightly tighten the drive
screws so as to centralise and secure the sleeve on the shaft.
NOTE:- a seal setting tool that bolts to the adaptor face is available for this task.
Ensure that the seal faces are still abutted and the working length is correct, then tighten the drive screws fully.
Take the remaining rotary head (1), lightly smear the O-ring with silicon based grease lubricant and place over the shaft.
Ensure it locates on the drive pins of the mechanical seal. Avoid getting any grease onto the lapped seal face.
Fit the seal seat (Item 12) to the carrier and retain with the retaining clamp. Ensure a new O-ring is fitted.
Pump types CD160M Mk 1/ CD400M

(Figure 26) HL110M/HL200M
Take the seal seat (11) from the drive end assembly and carefully push into the seat carrier. Fit a new O-ring to the carrier
and slide the assembly along the shaft to seat in the adaptor. Secure with cap head screws and washers.
Carefully remove the rotary head (10) and O-ring (9) from the assembly. Do not place the rotary head face down as this may
cause damage to the lapped seal face.
Take the sleeve assembly (8) and ensure that the drive screws (6) are fully retracted to prevent scratching of the shaft
during assembly.
Lightly smear the O-ring (9) with silicon based grease lubricant. Place the O-ring inside the rotary head (10). Avoid getting
Gently push the rotary head (10) onto the sleeve assembly (8) ensuring that the drive pins (7) are engaged in the slots of
the rotary head.
Carefully slide the sleeve assembly along the shaft until the seal faces butt together
Set the seal working length, apply thread locking compound (see Technical Data Section) and lightly tighten the drive
screws to centralise and secure the sleeve on the shaft. A special tool is available from Godwin Pumps Ltd to enable this
first seal working length to be set correctly. It is strongly recommended that this tool be used. Ensure that the seal faces are
still abutted and the working length is correct, then tighten the drive screws fully.
Carefully remove the rotary head (1) and O-ring (2) from the outboard assembly. Do not place the rotary head face down as
this may cause damage to the lapped seal face.
Take the sleeve assembly (3) and ensure that the drive screws (5) are fully retracted to prevent scratching of the shaft. Slide
the sleeve assembly along the shaft until it abuts the sleeve assembly (8) previously fitted. Apply thread locking compound
(see Technical Data Section) and secure in place by tightening the drive screws fully.
Lightly smear the O-ring (2) with a silicon based grease lubricant. Place the O-ring inside the rotary head (1). Avoid getting
Gently push the rotary head (1) along the shaft onto the sleeve assembly (3) ensuring that the drive pins (4) are engaged in
the slots of the rotary head.
Fit the seal seat (12) to the carrier and retain with the retaining clamp. Ensure a new O-ring is fitted.
95-0019-0000 Iss 11 21
Pump types CD300M/ CD500M

CD500M & HL260M only. Fit a new roll pin into the wear plate, carefully tapping it
in from the impeller side until it is flush with that side. It should protrude 2-3mm
from the seal side.
All Units. Take the seal seat (Item 3) from the assembly and carefully push into
the seat carrier, ensuring that for the CD500M & HL260M the protruding roll pin
fits into the groove in the back of the seal seat. Fit a new O-ring to the carrier and
slide the assembly along the shaft to seat in the adaptor. Secure with cap head
screws and washers.
CAUTION.
Failure to ensure the pin locates in the groove of the seal for CD500M & HL260M units will result in seal
seat breakage.
Ensure the O-ring(s) is/are in place inside the sleeve (2) carrying the double seal faces and carefully slide the whole onto
the shaft.
Fit the seal seat (1) to the carrier (CD300M, HL130M & HL225M), or to the wear
plate (CD500M & HL260M) and retain with the retaining clamp. Ensure a new O-
ring is fitted.
22 95-0019-0000 Iss 11
8.5.3 Fitting the wear plate

Pump types CD75/ CD80D/ CD80M/ CD100M/ CD103M/ CD150M
HL80
NC80/ NC100/ NC150
Fit the rear wear plate smearing the outside diameters and O-rings with oil to aid assembly. This will also help to prevent the
wear plate rusting into the pump body and ease later strip-downs
Pump types CD140M/ CD160M (Mk 1 & 2)/ CD180M/ CD200M/ CD225/ CD250M/ CD300M/ CD400M
HL100/ HL110M/ HL125MS/ HL150M/ HL150MHD/ HL200M/ HL130M/ HL160M/ HL225M/ HL250M
Slide the carrier over the shaft and attach with four off cap head socket screws. Position the rear wear plate and attach with
fasteners from the motor adaptor/bearing bracket/seal housing adaptor side.
Pump types CD500M

HL260M
Carefully place the rear wear plate over the shaft. It is recommended that the
seal seat is protected from contacting the shaft end by wrapping the shaft end
with a suitable soft material. Attach the wear plate with fasteners from the motor
adaptor/bearing bracket/seal housing adaptor side.
95-0019-0000 Iss 11 23
8.5.4 Fitting the impeller

Lock the pump shaft to prevent rotation.
Impeller clearance tolerances are given in the Technical Data section.
For all pumps except NC80/ NC100/ NC150:- Once the impeller is fitted the rear clearance must be checked. If the
clearance lies outside the tolerance, then remove the impeller, add or remove shims, and replace the impeller. Repeat until
a value within the tolerance is obtained.
NC80/ NC100/ NC150 only. Rear clearance is not measured for these pumps, however impeller hub must be free to turn.
Pump types CD75/ CD80D/ CD80M

Refit the shims (or new equivalents) removed during strip down.
Screw the impeller (right hand thread) directly onto the shaft. Check there is still a clearance and torque down fully.
Check the rear impeller clearance.
Pump types CD100M/ CD103M/ CD140M/ CD150M/ CD160M (Mk 1 & 2)/ / CD180M/ CD200M/ CD225/ CD250M
HL80/ HL100/ HL110M/ HL125MS/ HL150M/ HL150MHD/ HL200M
Refit the shims (or new equivalents) removed during strip down.
Screw the impeller (right hand thread) directly onto the shaft. Do not fit the self locking retaining screw at this stage. Check
there is still a clearance and torque down fully.
Check the rear impeller clearance. If within the permitted tolerance secure the impeller with the self locking retaining screw.

Refit the shims (or new equivalents) removed during strip down. If a 4mm thick impeller spacer was fitted ensure it is refitted
first with its internal radiused edge towards the shaft shoulder.
The impeller is splined. Carefully locate the impeller on the shaft and push back along the spline.
Fit the O-ring, clamping washer, tab washer and bolt. Tighten the bolt to the final torque given in the Technical Data section.
The pre-torque figure is only for use with a new shaft.
Check the rear impeller clearance. If within the permitted tolerance knock up the tabs on the tab washer.
Fit the cover using a new O-ring.

Lightly grease the shaft taper and the internal conical taper of the sleeve.
Adjust the adjusting screw so that its external face is flush with the external
face of the sleeve as shown in figure 28.
NOTE! The adjustment screw is LEFT HAND threaded
Insert the sleeve into the impeller with the taper facing out ensuring that the
flat face is seated correctly at the bottom of the impeller bore.
Mount the impeller on the shaft ensuring is fully pushed back on the taper.
Insert the impeller screw and washer to hold impeller in place to next step.
Hand tighten only.
Figure 28 Impeller sleeve and adjustment screw
24 95-0019-0000 Iss 11
8.5.5 Front cover & pump body fitting

Impeller clearance tolerances are given in the Technical Data section.
Fit the front cover/wear plate ensuring the fasteners are torqued down evenly in equal increments. Check the front
clearance. NOTE: - CD75 clearance is set automatically during assembly and no shimming or change in gaskets is required.
If the clearance lies outside the tolerance, then remove the front cover/pump body, add or remove shims/gaskets, and
replace the front cover/pump body. Repeat until a value within the tolerance is obtained.
Pump types CD75/ CD80D/ CD80M/ CD100M

The pump body and front cover are one piece fitted with studs that pass through the adaptor or bearing bracket, secured by
nuts and spring washers (see Figure 18 or Figure 19).
Refit the pump body complete with non-return valve and ejector package (if fitted) and secure with nuts and spring washers.
CD75: - No further work is required.
CD80D: - Check the front impeller clearance. Adjust the gaskets between pump body and bearing bracket/motor adaptor to
achieve the correct figure.
CD80M & CD100M: - Check the front impeller clearance. Adjust the shims between pump body and front wear plate to
achieve the correct figure.
Pump types CD103M/ CD140M/ CD150M/ CD160M (Mk 1 & 2)/ CD180M
CD225/ CD200M/ CD250M/ CD300M/ CD400M/ CD500M
HL80/ HL100/ HL110M/ HL125MS/ HL150M/ HL150MHD/ HL200M/ HL130M/ HL160M/ HL225M/
HL250M/ HL260M
Larger pump bodies (HL80, CD300M, CD400M, CD500M, HL160M, HL225M, HL250M but not HL130M) were probably not
removed as they have sufficient room to allow the seal to be removed.
For other units or if the larger pump body has been removed, fit the body, guiding the body studs into the adaptor holes.
Secure the peripheral fasteners.
Attach the front cover and wearplate assembly to the pump body (see Figure 20) using the peripheral fasteners.
NOTE: - The CD400M and CD500M have an adaptor plate fitted between the front cover and pump body. It carries the
front wearplate and is located by a spigot on the front cover. It normally remains with the front cover, but may have been
dismantled and require refitting.
Check the front impeller clearance. Adjust the shims between pump body and front wear plate to achieve the correct figure.

Fit the body, guiding the body studs into the adaptor holes. Secure the peripheral fasteners.
Attach the front cover and wear plate assembly to the
pump body (see Figure 20) using the peripheral
fasteners.
Unscrew and remove the impeller retaining screw and
washer.
Insert a 65mm long 12 A/F hexagon socket bit
through the central hole of the impeller and locate it in
the hexagon of the adjustment screw.
Using an extension bar turn the adjustment screw
slowly clockwise until the impeller makes contact with
the wear plate and the impeller cannot be rotated by
hand.
Remove the tools.
Install the anti rotation bar through the access plug
hole in the volute.
Lightly grease the impeller retaining screw and washer. Fit and tighten to the correct torque (see Technical Data section).
Then tighten the impeller retention screw an extra 1/8 turn (45°), this procedure will ensure the correct front clearance is
obtained.
Remove the anti rotation bar and replace access plug.
8.5.6 Preparing for service

Reconnect compressor or vacuum pump lines.
Fill the chamber around the mechanical seal with the correct quantity and grade of coolant. See Section 8.2 for positions
and Technical data section for grade and quantity.
95-0019-0000 Iss 11 25
8.6 Bearing Bracket & Motor Adaptor Dismantling

8.6.1 Preparation for dismantling
Use suitable lifting gear to remove the pump assembly from the driver. It may be convenient to remove the air compressor
assembly or vacuum pump (if fitted) before doing so. See Section 8.11.1 for details.
Support the pump unit in a suitable manner before commencing further strip down.
Carry out the instructions for seal removal (Section 0) before commencing any work detailed in this section.
8.6.2 Dismantling
Pump types CD75/ CD80D/ CD80M/ CD100M/ CD103M/ CD140M/ CD150M/ CD160M/ CD180M/ CD200M/ CD225/
CD250M
NC80/ NC100/ NC150
1) CD160M, CD180M
Undo the fasteners holding the seal-housing adaptor to the bearing housing and remove the seal housing adaptor.
Undo the fasteners holding the SAE adaptor to the bearing housing and remove the SAE adaptor.
2) Unscrew the drive end bearing cover fasteners and remove the drive end bearing cover.
3) CD75, CD80D, CD80M & CD160M motor adaptor units.
Release the tab washer and remove the bearing locknut.
4) Extract the shaft and bearing assembly.
5) Remove pump end bearing cover on bearing bracket units where the cover is retained by screws. CD100, CD103M,
CD150M, CD250M, NC80, NC100, & NC150 motor adaptor units have their pump end bearing cover retained by a
circlip. Do not remove the clip, cover or pump end outer bearing race unless required for cleaning purposes or because
of damage.
6) If necessary, remove the bearing inner races from the shaft.
7) Inspect all parts for damage or wear and replace as necessary. All lip seals and O-rings must be replaced.
Pump types HL80/ HL100M/ HL110M/ HL125M/ HL150M/ HL200M
1) HL80
Undo and remove the nuts and spring washers from the studs holding the pump body to the bearing bracket or motor
adaptor.
Undo and remove the pump body holding down bolts (if fitted). Remove the pump body.
Pull the collar and tolerance ring off the pump end of the shaft.
HL100M, HL125MS, HL150M, HL150MHD, HL110M & HL200M
Release the nuts on the bolts holding the seal housing adaptor to the bearing bracket and remove the fasteners.
Remove the adaptor.
For pumps other than the HL110M or HL200M this will include the shaft lip seal.
For the HL110M or HL200M this will include the rear mechanical seal seat if it has not already been removed.
2) Unscrew both bearing cover fasteners and remove the bearing covers.
3) HL100M, HL125MS, HL150M, HL150MHD, HL110M & HL200M
Release the pump end tab washer, lock the shaft against rotation and remove the bearing locknut.
4) Extract the shaft and bearing assembly from the drive end, leaving the pump end outer bearing race in place.
5) HL80
Motor adaptor units have their pump end bearing cover retained by a circlip. Do not remove the clip, cover or pump end
outer bearing race unless required for cleaning purposes or because of damage.
6) Remove pump end bearing cover.
7) If necessary, remove the bearing inner races from the shaft.
26 95-0019-0000 Iss 11
Pump types CD300M/ CD400M (Open Coupled)

1) Remove the pump body and the vacuum pump support plate (if fitted this covers the aperture on top of the bearing
bracket.
2) Unscrew both the drive end and pump end bearing cover fasteners and remove both covers.
3) Release the tabs from the pump end lock washer. Lock the shaft against rotation and unscrew and remove the pump
end bearing locknut and tab washer.
4) Press the shaft and bearing assembly out of the bearing bracket.
5) Press the internal bearing covers and roller bearing outer race out of the bearing bracket.
6) Release the tabs from the drive end locknut tab washer and unscrew and remove the locknut and tab washer.
7) Remove the angular contact bearings and roller bearing inner race from the shaft.
Pump types HL130M/ HL160M/ HL225M/ HL250M/ HL260M

CD300M (Close Coupled)/ CD500M
1) Remove the grease nipple and extension pipe where they protrude through the mechanical seal adaptor.
2) Release the nuts on the bolts holding the adaptor to the bearing bracket and remove the fasteners. Remove the
adaptor.
3) If a close coupling adaptor is fitted then remove the grease nipple and extension pipe where they protrude through the
adaptor. Remove the adaptor.
4) Unscrew the drive end bearing cover fasteners and remove the bearing cover complete with lip seal. Note that the inner
bearing cover will now be loose on the shaft.
5) Release the tab washer and remove the bearing locknut.
6) Extract the shaft and bearing assembly by pressing from the pump end. Take care that the loose inner bearing cover
does not catch on or damage any part of the shaft assembly during this process. Remove the inner bearing cover.
7) Unscrew the pump end bearing cover fastenings. Note that three of these hold the inner bearing cover in place.
Remove the inner bearing cover and pump end bearing cover.
8) If necessary, remove the angular contact bearings and the roller bearing inner race from the shaft and press out the
roller bearing outer race from the bearing bracket.
95-0019-0000 Iss 11 27
8.7 Bearing Bracket & Motor Adaptor Assembly
8.7.1 Preparation for assembly

Ensure all parts are clean and free from burrs.
The use of a temperature controlled bearing heater is
recommended. A consistent 110°C is the optimum temperature
for the bearings to achieve before fitting. In the following text
wherever “heat the bearing” is stated it means to 110°C. Never
overheat a bearing or allow it to remain at that temperature for
longer than its fitting time.
CAUTION.
Bearing races must be pressed into position
and not hammered either directly or by drift. A
purpose designed ‘top-hat’ type of assembly
tool as acceptable. Direct hammering will
damage the bearing or rollers. Drift hammering
will introduce swarf into the assembly. Either
will result in early bearing failure.
8.7.2 Assembly
Pump types CD75/ CD80D MA Units
1) Heat the roller bearing. Once up to temperature, slide it hard against the shaft shoulder, holding it there for a minimum
of 30 seconds. This allows the race to grip the shaft and prevent it from creeping away from the shoulder during
cooling. Let the assembly cool completely.
2) Fit the inner and outer bearing spacers.
3) Heat the ball bearing. Once up to temperature, slide it hard against the inner spacer, holding it there for a minimum of
30 seconds. This allows the race to grip the shaft and prevent it from creeping away from the spacer during cooling. Let
the assembly cool completely.
4) Fit the tab washer and locknut. Prise up at least two tabs to lock the nut in position.
5) Pack the bearings with grease allowing sufficient excess to one-third fill the cavities at each side of the bearings.
6) Position the motor adaptor with the shaft axis vertical (pump end down). Press the shaft assembly into the motor
adaptor.
7) Grease the pump end lip seal and press it into the motor adaptor body (lip facing in).
8) Grease the drive end lip seal and press it into the bearing cover (lip facing in).
9) Fit the bearing cover and tighten down the fasteners evenly to the recommended torque.
10) Fit ancillary components.
28 95-0019-0000 Iss 11
Pump types CD75 BB Units

CD80M/ CD100M/ CD150M/ CD200M
MA & BB Units
NC80/ NC100/ NC150
CD103M MA Units
1) Heat both inner bearing races. Once up to temperature, slide them up hard against the shaft shoulders and hold in
position for a minimum of 30 seconds. This allows the races to grip the shaft and prevent them from creeping away
from the shoulder during cooling. Let the assembly cool completely.
2) Fill the annular space between the bearing inner races with grease and lightly grease the bearing rollers and the
raceways of the inner races to ensure seating.
3) Motor Adaptor units: - If the pump end bearing cover and circlip have been removed, refit these parts ensuring that,
after initial fitting, the bearing cover is pressed hard back against the retaining circlip to prevent excess play in the final
bearing assembly. Do not fit lip seal to cover.
Bearing bracket units: - Fit the pump end bearing cover. Do not fit lip seal.
4) Fit the pump end bearing outer into the housing ensuring it is pressed hard up against the bearing cover.
Bearing bracket units: - Lock into position with grub screw.
5) Position the motor adaptor/bearing bracket with the shaft axis vertical (pump end down). Lower the shaft/bearing inner
assembly into position.
6) Press the drive end bearing outer into the housing until it just meets the inner race.
7) Fit the drive end bearing cap (without lip seal) and hand tighten the retaining screws. Rotate the shaft assembly – by
hand – about a dozen times to ensure free movement.
8) Using a dial indicator located against the end face of the drive end of the shaft, measure the end float of the shaft. Add
shims under the drive end bearing cover to achieve the end float given in the Technical Data section. Rotate the shaft
assembly by hand several times and check the end float again. Adjust as necessary.
9) Remove drive end bearing cover and shims.
10) Grease the motor adaptor/bearing bracket assembly using the external grease nipple until a continuous ring of grease
is witnessed emerging through both bearings.
11) Grease the drive end lip seal and press it into the drive-end bearing cover (seal lip facing in). Add a small amount of
grease to the internal cavity of the cover and refit.
12) Motor adaptor units: - Grease the bearing cover pump end lip seal and press it into the pump end bearing cover (seal
lip facing in).
Bearing bracket units: - Remove pump end bearing cover and press both lip seals into place (seal lip facing out at each
end). Add a small amount of grease to the internal cavity of the cover and refit.
13) Check that the assembly rotates freely.
14) Motor adaptor units: - Grease the pump end lip seal and fit (lip facing out) to the shaft collar starting at the small end of
the collar and finishing about 5mm from the large end. Press the shaft collar into place at the pump end. The lip seal
will remain slightly proud. Press the lip seal home flush with the inner face of the casting.
95-0019-0000 Iss 11 29
Pump types CD140M/ CD160M/ CD180M MA Units

HL110M
CD225 All Units
HL100M/ HL125MS/ HL150M/ HL150MHD/ HL200M
1) Heat the bearings detailed below: -
CD140M, CD225, CD250M, HL100M, HL110M, HL125MS, HL150M motor adaptor
Single roller bearing inner race (pump end) and the complete spherical roller bearing (drive end)
CD160M, CD180M, HL150MHD & HL200M motor adaptor; CD225, CD250M, HL100M, HL125MS, HL150M & HL200M
bearing bracket
Single roller bearing inner race (pump end) and two angular contact bearings (drive end)
2) Once up to temperature, take the appropriate drive end bearing. Slide it or them up hard against the shaft shoulder.
Hold them there for a minimum of 30 seconds. This allows the races to grip the shaft and prevent them from creeping
away from the shoulders during cooling. Let the assembly cool completely. If these are the angular contact bearings,
ensure they are fitted in ‘O’ arrangement, i.e. with the two outer races ‘trapped’ between the balls.
3) Fit the drive end tab washer and locknut. Prise up at least two tabs to lock the nut in position.
4) Position the bearing spacer on the shaft.
5) Take the single roller bearing inner race and slide it up hard against the shaft shoulder. Hold it there for a minimum of
30 seconds to allow the race to grip the shaft and prevent it creeping away from the shoulder during cooling. Let the
assembly cool completely.
6) Take the single roller bearing outer race and press it into the bearing bracket/motor adaptor at the pump end. Use the
pump end bearing cover, without the lip seal fitted, to press it into its final position.
7) Pre-pack the spherical roller bearing or the two angular contact bearings with grease.
8) Lightly grease the bearing rollers and the raceway of the outer race of the single roller bearing.
9) Position the motor adaptor/bearing bracket with the shaft axis horizontal (unit level). Press the shaft/bearing assembly
into the bearing bracket/motor adaptor. Position the shaft/bearing assembly using the drive-end bearing cover (without
a lip seal).
10) Remove both bearing covers. Fit the pump end bearing tab washer and lock nut. Prise up at least two tabs to lock the
nut in position.
11) Fit a lip seal into each bearing cover. Fit the bearing covers and tighten the retaining screws. Rotate the shaft assembly
– by hand – about a dozen times to ensure free movement.
12) Temporarily fit grease nipples in the motor adaptor or bearing bracket in the grease relief valve positions. Pump grease
in until it is witnessed emerging continuously through both final nipple locations in the bearing covers.
13) Remove both bearing covers. Add a small amount of grease to the internal cavity of the covers, grease the lip seals
and refit.
14) Remove the grease nipples and refit them in the bearing covers. Fit the grease relief valves in their places
30 95-0019-0000 Iss 11

1) Heat the single roller bearing inner race and the two angular contact bearings. Once up
to temperature, take the two angular contact bearings and slide them up hard against
the shaft shoulder at the drive end.
The bearing orientation is in ‘O’ arrangement, i.e. with the two outer races ‘trapped’
between the balls.
2) Take the single roller bearing inner race and slide it up hard against the shaft shoulder.
3) Use the lock nuts without tab washers to hole them hard against the shoulders for a
minimum of 30 seconds to allow the races to grip the shaft and prevent them creeping
away from the shoulders during cooling. Let the assembly cool completely. Remove both
locknuts.
4) Fit the drive end tab washer and locknut. Tighten the locknut securely with a C spanner. Prise up at least two tabs to
lock the nut in position.
5) Locate and secure the bearing bracket on an assembly jig or bench.
6) Take the single roller bearing outer race and press it into the bearing
bracket at the pump end. Use the pump end bearing cover, without the lip
seal fitted, to press it into its final position. Remove the cover.
7) Secure the shaft aligning jig to the pump end of the bearing bracket. Place
the two bearing inner covers in the bracket. Lift the shaft horizontally using
suitable over head lifting equipment and slide the shaft assembly in to the
bracket.
8) Fit the lip seal to the drive end bearing cover (seal lip facing in). Smear the
lip seal lightly with oil and fit the cover over the shaft and secure it to the
bearing bracket and the inner cover.
9) Remove the shaft-aligning jig. Fit the non-drive end bearing tab washer and
locknut. Tighten the lock nut securely with a C spanner. Prise up at least two
tabs to lock the nut in position.
10) Fit the lip seal to the pump end bearing cover (seal lip facing in). Smear the
lip seal lightly with oil and fit the cover over the shaft and secure it to the
bearing bracket and the inner cover.
11) Fit the bearing cover extension pipes and grease nipples. Charge the
bearings with grease until it is witnessed just emerging from the inner
covers. During this process it is important to continually rotate the shaft.
When completed remove the grease extension pipes temporarily to avoid
damage during further assembly. Plug the bearing cover holes to avoid
grease contamination.
95-0019-0000 Iss 11 31
8.8 Air Compressor
Smaller pumps in the range are fitted with an air compressor. The following instructions apply to those units only.
8.8.1 Filter Replacement

The air filter is of the element type. Remove air filter’s cover and replace the element if necessary. Check all pipe work for
leakage and damage. Repair or replace as necessary.
8.9 Vacuum Pump

The vacuum pump (if fitted) forms only part of a complete system.
8.10 Non Return Valve

Non return valves are a major cause of priming failure. Should this occur then check the condition of the flap/seat/ball
dependant on the type of valve fitted. Look for cuts scores, marks or blemishes on all rubber like materials. Replace where
necessary.
8.11 Drive Belts

8.11.1 Timing/HTD Belt Replacement (air compressor)
1) If the compressor has external oil feed and return pipes, drain the compressor of oil and disconnect the pipes.
2) Remove the pulley guard.
3) Undo the coupling sufficiently to allow a new belt to be passed over the shaft end.
4) Release the fasteners to allow the air compressor to be tipped forward. Remove the belt.
5) Fit a new belt and tighten air compressor fasteners.
6) Check the belt tension to ensure that it complies with the belt manufacturer recommendations (see Technical Data
section). Add or remove shims to achieve this.
7) Reassemble the coupling.
8) Refit the pulley guard.
9) Replace the compressor oil feed and return pipes.
Refill the compressor with oil (see Technical Data section).
8.11.2 Belt Replacement (vacuum pump)

1) Remove the pulley guard.
2) Release the vacuum pump adjustment screws and slacken the holding down bolts. This will allow the vacuum pump to
be moved and release the belt tension.
3) Undo the coupling sufficiently to allow a new belt to be passed over the shaft end.
4) Remove the old belt and fit the new.
5) Tighten the vacuum pump holding down bolts sufficiently so that the pump can still slide but not tip. Use the adjusting
screw to push the vacuum pump into place. Tighten the holding down bolts fully. Ensure the belt is correctly aligned.
6) Check the belt tension to ensure that it complies with the belt manufacturer recommendations. (See Technical Data
section). Adjust as necessary.
7) Reassemble the coupling.
8) Refit the pulley guard.
32 95-0019-0000 Iss 11
8.11.3 Link belt tensioning and replacement
Adjusting
studs
3 off
Clamping
screws
2 off
Figure 29 Link belt driven compressor (shown on a CD150 bearing bracket - guards and belt removed)
A) Checking / Tensioning
Link belt tension must be checked and, if necessary, adjusted weekly or after every 100 hrs operation.
See Section 11 for force/deflection details.
CAUTION.
Link belt tension must be maintained within the specified limits. Belts that are too slack or too tight will wear
out quickly, damage the pulleys and will result in loss of pump performance.
To check/adjust tension:-
1) Remove at least one half of the guard.
2) Check the belt condition. Look for signs of dust and/or pulley wear (belt over tensioned) or smearing of the belt sides
(belt under tensioned and slipping).
3) Using a spring balance and rule (or a belt tension indicator) check the force and deflection of both belts.
4) If adjustment is required, slacken the two clamping screws (see Figure 29) enough to allow the compressor carrying
frame to slide on the supporting angle frame.
5) Slacken the 3 off adjusting stud nuts on top of the carrying frame (see Figure 29).
6) Evenly adjust the nuts under the carrying frame to raise or lower the compressor.
CAUTION.
Ensure the compressor drive shaft remains parallel to the pump shaft.
Check visually that the drive belts are perpendicular to the shaft axes.
Use a straight edge across the pulley faces for confirmation.
Failure to ensure that the drive is perpendicular will result in premature belt wear and early failure.
7) Check the tension and deflection are within the specified range and that it is the same within 2 or 3% on both belts.
8) Correct tension: - Tighten the 3 off adjusting stud nuts (standard torque for nuts on studs – see Section 11) above the
carrying frame. Go to instruction 20).
9) Tension not achievable because the limit of adjustment has been reached:- A link must be removed from each belt.
Lower the carrying frame to the bottom of its adjustment and remove the belts from the pulleys.
CAUTION.
The drive must be slack enough to allow the belt to be removed without forcing it over the pulley rim which
will damage the belt and lead to premature failure.
95-0019-0000 Iss 11 33
10) Each belt link is tabbed to the next two. To disconnect turn the belt inside out so the tabs point outwards.
11) Bend the belt backwards as far as possible so that the tabs protrude. Hold the belt in this position with one hand and
twist one tab so that it is parallel with the slot of the underlying link.
12) Pull the underlying link over the twisted tab.
13) The belt is now held together by only one tab. Rotate the two parts 90° and remove this remaining tab from the
underlying link.
14) Remove one link from the belt by repeating instructions 11) to 13).
15) To rejoin the belt, ensure it is still threaded around the pump shaft and push one end tab through two links at once on
the other end.
16) Flex the belt until the second tab can be inserted by twisting into place.
17) Ensure both tabs have returned to their normal orientation. Reverse the belt so that the tabs are inside.
18) Refit the belt over both pulleys. Go to instruction 6).
19) Tighten the 2 off clamping screws (standard torque for nuts and bolts – see Section 11).
20) Recheck the force/deflection to ensure no movement has taken place whilst tightening up.
21) Replace the guard.
22) Run the pump for thirty minutes; recheck the tension adjusting if necessary.
23) The pump is now ready for service.
B) Fitting a New Belt

1) Remove the guard.
2) Slacken the two clamping screws (see Figure 29) enough to allow the compressor carrying frame to slide on the
supporting angle frame.
3) Slacken the 3 off adjusting stud nuts on top of the carrying frame (see Figure 29).
4) If the belts are still intact lower the carrying frame by evenly adjusting the nuts underneath until the belts can be
removed.
5) Dismantle the belts as described in instructions 11) to 13) of the Tensioning section above.
6) Thoroughly clean the area, removing all traces of debris and foreign objects.
7) Adjust the carrying frame so that the clamping screws are approximately 10mm above the bottom of the adjusting slots.
8) Take a new length of belting and place the end in the top groove of the compressor pulley. Thread the remainder of the
belt around the corresponding groove of the bottom pulley and back up to overlap the first end.
9) Mark the point at which the belt needs to be dismantled with a pencil or felt tipped pen. Dismantle the belt as described
in instructions 11) to 13) of the Tensioning section above. Count the number of links and make a second belt of the
same length.
10) Make the belts up as described in instructions 15) to 17) of the Tensioning section above.
11) Lower the carrying frame to the bottom by undoing the adjusting stud nuts underneath the frame.
12) Fit the belts over the pulleys. Evenly adjust the nuts under the carrying frame to raise the compressor until the belts
are close to the required tension (See Section 11).
13) Check the tension and deflection are within the specified range and that it is the same within 2 or 3% on both belts.
14) Tighten the 3 off adjusting stud nuts (standard torque for nuts on studs – see Section 11) above the carrying frame.
15) Tighten the 2 off clamping screws (standard torque for nuts and bolts – see Section 11).
16) Recheck the force/deflection to ensure no movement has taken place whilst tightening up.
17) Replace the guard.
18) Run the pump for thirty minutes; recheck the tension adjusting if necessary.
19) The pump is now ready for service.
34 95-0019-0000 Iss 11
9 TOOLS
9.1 Tool Kits
Pump MA version BB version
CD75 ACC-PT-01 √
CD80D ACC-PT-03
CD80M ACC-PT-06* ACC-PT-02*
CD100M ACC-PT-06* ACC-PT-02*
CD103M ACC-PT-31*
CD140M
ACC-PT-07 ACC-PT-08
CD150M
ACC-PT-27* ACC-PT-28*
ACC-PT-33 (Mk1)
CD160M
ACC-PT-36 (Mk2)
ACC-PT-09 ACC-PT-20
CD200M
ACC-PT-29* ACC-PT-22*
CD225 ACC-PT-29* ACC-PT-22*
CD250M ACC-PT-09 ACC-PT-20
CD300M ACC-PT-30
CD400M ACC-PT-38
CD500M ACC-PT-40

ACC-PT-11 ACC-PT-12
HL80 ACC-PT-25* ACC-PT-26*
HL100M
HL125MS
ACC-PT-19 ACC-PT-21
HL150M
HL150MHD
HL110M ACC-PT-35
HL130M
HL160M
ACC-PT-37
HL225M
HL250M
HL200M ACC-PT-34
HL260M ACC-PT-41
NC80 ACC-PT-42 ACC-PT-43
The kits generally comprise of: - a special spanner and locating tool to aid in impeller removal/fitting.
* These tool sets have an impeller spanner designed for use with a 1” square drive torque multiplier
 a locking bar to prevent shaft rotation
 a sleeve to aid in fitting the mechanical seal
 a sleeve to aid in pressing the bearing home on the shaft
 a tool to aid in assembly/removal of the rear wear plate
 a tool to aid correct location of the lip seals in the bearing covers
 a tool to position the bearing spacer (where applicable) in the bracket
 a seal assembly and setting tool.
95-0019-0000 Iss 11 35
9.2 Special Tools

Pump Tool Purpose Tool Part Number
HL110M/ HL200M First seal setting 54-2320-9811

First seal setting 54-1394-9811
CD300M
(multi-piece seal) (Not required for one piece
HL130M/ HL160M/ HL250M
seal builds)
CD300M/CD400M Shaft aligning jig 54-1468-9811
HL130M/ HL160M/ HL250M
CD400M/ CD500M Workshop combination tool for fitting/removing 54-2215-9801
HL130M/ HL160M/ HL225M/ impellers with or without volutes fitted (requires
HL250M/ HL260M lifting gear).
10 FAULT FINDING
If possible fit a suction and pressure gauge to assist fault finding and check pump rating
FAULT
Liquid flow ceases
Excessive power
Insufficient liquid
Seal housing oil

Pump does not
consumption
overheating
Vibration or
emulsified
delivered
prime
POSSIBLE CAUSE
Suction lift too great √ √ √
Insufficient water at suction inlet √ √
Suction inlet or strainer blocked √ √ √
Separation tank filter blocked √ √ √
Suction line not air tight √ √
Suction hose collapsed √ √ √
Non return valve not seating √
Mechanical seal drawing air into pump √ √ √
Ejector jet or nozzle blocked or badly worn √ √
Compressor
√
units only
Ejector non-return valve ball stuck

Compressor pipe leaking air √
Compressor not delivering sufficient air √
Compressor/vacuum pump drive belt faulty √
Discharge head too high √
Obstruction in body or impeller √ √ √ √
Impeller excessively worn or damaged √ √
Delivery hose punctured or blocked √ √
Incorrect speed (if diesel driven) √ √ √
Incorrect rotation (if electric motor driven) √
Excessive air leak in suction hose √
Viscosity and/or SG of liquid too high √
Cavitation due to excessive suction lift √
Mechanical seal damaged or worn √
36 95-0019-0000 Iss 11
11 TECHNICAL DATA
11.1 Designations, Sizes & Capacities
11.1.1 CD range
(1)
Weight (kg) Speed Range
Max solids
Max. head
Max work
temp (°C)
bore(ins)
Max flow
Suction /
pressure
handling
Delivery
working
CD
(m /hr)
(mm)
(bar)
Max
Engine
(m)
driven
driven
Motor
3
Range Min Norm Max
CD75 3/2 49 22 40 80 2.14 79 83 1500 2500 3000

CD80D 3/3 94 21 40 80 4.03 126 1400 2000 3000
CD80M 3/3 83 21 40 80 2.8 186 146 1200 1800 2200
CD100M 4/4 160 35 45 100 3.5 202 169 1200 1700 2200
CD103M 4/4 200 44 75 80 4.4 220 200 1200 1800 2200
CD140M 4/4 250 85 75 80 9 510 1200 1800 2000
CD150M 6/6 450 49 65 80 4 285 254 1200 1500 2200
CD160M 6/6 460 80 75 80 9 610 580 1200 1800 2000
CD180M 8/6 75 80 9 600 570 1200 1800 2000
CD200M 8/8 790 50 75 80 5 310 1400 2000 2200
CD225M 8/8 790 55 80 80 5.5 385 411 1400 2000 2200
CD250M 10/10 850 55 80 80 5.5 400 411 1400 2000 2200
CD300M 12/12 1300 55 95 80 6.1 890 (2) 1200 1500 1800
(3)
2383
CD400M 18/16 2140 40 125 80 6.1 1835 (4) 900 1100 1200
(5)
465
(4)
1730
CD500M 20/18 2700 75 137 80 7.5 (5) 800 1000 1200
555
95-0019-0000 Iss 11 37
11.1.2 HL Range
(1)
Max solids
Max. head
Max work
bore (ins)
temp (°C)
Max flow
Suction /
pressure
handling
Delivery
working
HL
(m /hr)
(mm)
(bar)
Max
Engine
(m)
driven
driven
Motor
3
Range Min Norm Max
HL80 4/3 107 90 25 80 10 258 262 1400 1800 2400

HL100M 4/4 180 125 35 80 14.3 423 402 1400 1800 2200
HL110M 4/3 110 188 20 80 19 1400 2000 2200
HL125MS 6/4 300 125 35 80 14.3 446 456 1400 2000 2400
(6)
HL130M 6/4 305 190 23 80 19 1095 1200 1800 2100
HL150M 6/6 320 125 35 80 14.8 629 598 1400 2000 2400
HL150MHD 6/6 320 150 35 80 14.8 592 1400 2000 2400
HL160M 8/6 465 182 35 80 19 1155 1200 1800 2000
6/8 or
HL200M 540 97 38 80 11.4 689 1200 1600 2200
6/6
(6)
HL225M 10/8 830 110 65 90 11 905 1200 1800 2000
HL250M 12/10 1080 116 65 80 13 986 1200 1800 2000
HL260M 10/8 1081 150 50 80 16 1440 1200 1800 1800
NOTES: -
(1) Weights are based on cast iron bareshaft pumps fitted with compressors. Different materials or additional
equipment can significantly affect the weight.
(2) Bareshaft open coupled unit with individual bearing bracket.
(3) Vacuum primed unit with gearbox.
(4) Ejector (less compressor) primed unit less gear box.
(5) Gearbox.
(6) Close coupled units with individual bearing bracket.
11.1.3 NC Range
(1)
Max solids
Max. head
Max work
temp (°C)
bore(ins)
Max flow
Suction /
pressure
handling
Delivery
working
NC
(m /hr)
(mm)
(bar)
Max
Engine
(m)
driven
driven
Motor
3
Range Min Norm Max
NC80 4/3 138 32 31 80 4 1200 1800 2200

NC100 4/4 230 45 35 80 5.5 1200 1800 2200
NC150 6/6 400 59 42 80 4.8 1200 1800 2200
38 95-0019-0000 Iss 11
Pump Type
CD75
CD225
CD80D
CD80M
CD100M
CD103M
CD150M
CD140M
CD180M
CD200M
CD250M
CD300M
CD400M
CD500M
Detail
CD160M Mk1
CD160M Mk 2
95-0019-0000 Iss 11
MA Flange SAE 5 4 3 2 or 3 4 3 1 (2) N/A 0 or 1
0.127 to 0.127 to
11.2 CD Range data
Shaft end float 0.33mm Nominal bearing clearance only 0.33mm Nominal bearing clearance only
0.075 to 0.10mm (0.003” to 0.004”)
mm (ins) (0.005” to 0.05mm (0.002”) max (0.005” to 0.05mm (0.002”) max
0.013”) 0.013”)
Impeller clearances front & rear (rear Cast Iron Imp/Wear Plate = 0.50 to 0.625mm (0.020” to 0.025”)
only on CD75)mm(ins) Hard Iron & Stainless Steel Imp/Wear Plate = 0.625 to 0.762mm (0.025” to 0.030”)
Impeller torque 30.0 31.0 53.0 180.0 320.0

33.0 (46.0) 563.0 (763.0) 320.0 (434.0) N/A
lbs.ft(N-m) (41.0) (42.0) (72.0) (244.0) (434.0)
New shaft 570.0 (776.0) then

Impeller bolt torque
N/A 40.0 (54.2) 100 (135.6) relax to 177.0 (240)
lbs.ft(N-m) Existing shaft 177.0 (240)
Shaft diameter at seal position (mm) 40 50 60 75 40 50 75 90 110
Inboard
Inboard 37.0±0.3
37.0±0.3 32.0±0. Outboard 50.0 N/A
Seal working length (mm) 32.0±0.3 34.0±0.3 39.0±0.3 34.0±0.3
Outboard 3 45.5±0.5 ±0.5 (1)
45.5±0.5
N/A (1)
Grease Texaco Starplex EP2, Shell Nertia HV, Mobil SHV 46, Total Multis Complex EP2, Belesta XPG
50/50
Type Oil. Any SAE 20/20 or BIOPUS 46 Biodegradable water/
glycol
Seal
Coolant Capacity (litres) 0.5 1.75 3.8 1 6 6.8 7
Vol – Max to Min (litres) N/A 0.35 0.5 N/A 0.6 0.6 1.3
Compressor oil (if not fed from

Total Cortusa 100
engine)
NOTES:-
(1) Seal length is not applicable for units with a one piece seal. The seal length is set automatically on installation. Where other figures are given these are for units with a multi piece seal.
(2) Only for close coupled units.
39
40
Pump Type
HL80
HL100M
HL110M
HL150M
HL200M
HL130M
HL160M
HL225M
HL250M
HL260M
Hl125MS
HL150MHD
Detail
MA Flange SAE 4 3 2 or 3 3 2 0 or 1
0.127 to Nominal bearing 0.127 to

0.075 to
Shaft end float 0.33mm clearance only 0.33mm Nominal bearing clearance only
0.10mm (0.003”
mm (ins) (0.005” to 0.05mm (0.005” to 0.05mm (0.002”) max
to 0.004”)
0.013”) (0.002”) m 0.013”)
Cast Iron Imp/Wear Plate = 0.50 to 0.625mm (0.020” to 0.025”)

Impeller clearances front & rear Hard Iron & Stainless Steel Imp/Wear Plate = 0.625 to 0.762mm (0.025” to 0.030”)
11.3 HL Range data
Impeller torque 378.0 517.0 563.0

147.0 (199.0) 563.0 (763.0) 378.0 (513.0) N/A
lbs.ft(N-m) (513.0) (701.0) (763.0)
New shaft 570.0 (776.0)

40 (54.2) 100.0 (135.6) then relax to 177.0 (240)
lbs.ft(N-m) Existing shaft 177.0 (240)
Shaft diameter at seal position (mm) 40 50 60 50 60 75 110
Inboard 37.0±0.3 Outboard

Seal working length (mm) 32.0±0.3 34.0±0.3 34.0±0.3 39.0±0.3 45.5±0.5 N/A (1)
N/A (1) N/A (1)
Rocol Sapphire
Type Texaco Starplex EP2, Shell Nertia HV, Mobil SHV 46, Total Multis Complex EP2, Belesta XPG
Premier
Grease Initial fill 160 grms

Relubrication 1500 – 2300 hrs
period/quantity 80 – 130 grms

50/50
Type Oil. Any SAE 20/20 or BIOPUS 46 Biodegradable
water/glycol
5.5 litres initial fill.
Seal
Capacity (litres) 5.25 5.25 Top up to full mark on 7.3
Coolant dipstick after 1 hr running
Vol – Max to Min (litres) N/A 0.5 N/A 0.6 1.4

Total Cortusa 100
engine)
NOTES:-
(1) Seal length is not applicable for units with a one piece seal. The seal length is set automatically on installation. Where other figures are given these are for units with a multi
piece seal.
95-0019-0000 Iss 11
Pump Type
NC80
NC100
NC150
Detail
95-0019-0000 Iss 11
MA Flange SAE 4
11.4 NC Range Data
Shaft end float 0.075 to 0.10mm (0.003” to

mm (ins) 0.004”)
Impeller clearance front 0.2 - 0.8 mm

56.0 (76.0)
lbs.ft(N-m)
Shaft diameter at seal position (mm) 40
Seal working length (mm) 32.0±0.3
Texaco Starplex EP2, Shell

Nertia HV, Mobil SHV 46, Total
Grease Multis Complex EP2, Belesta
XPG
Oil. Any SAE 20/20 or BIOPUS

Type 46 Biodegradable
Seal
Coolant Capacity (litres) 0.5
Vol – Max to Min (litres) N/A

Total Cortusa 100
engine)
41
11.5 Spanner Torques

The following tables give the recommended tightening torques for general purpose metric and UNC fasteners. They are to
be used only when the joint is metal to metal (i.e. no joints or gaskets) and no special figures (e.g. for impeller retaining
bolts) have been quoted.
Table 1 Metric Fasteners
Steel Stainless
Torque (N-m)
Thread Size Nuts & Bolts Nuts on Studs All
M6 x 1.0 11.7 4.6 9
M8 x 1.25 28 11 22
M10 x 1.5 56 22 44
M12 x 1.75 98 38 76
M16 x 2.0 244 95 187
M20 x 2.5 476 185 364
M24 x 3.0 822 320 629
M30 x 3.5 1633 633 1240
Table 2 UNC Fasteners
Steel Stainless
Torque (N-m)
Thread Size Nuts & Bolts Nuts on Studs All
¼” - 20 13.5 5.4 10.5
5/16” – 18 27.1 10.5 21.0
3/8” – 16 48.8 20 37.8
7/16” – 14 74.6 30 57.8
½” – 13 122 48 94.6
5/8” – 11 237.3 95 183.9
¾” – 10 420.4 167 325.8
7/8” – 9 664.4 266 514.9
1” - 8 1003 401 777.3
Table 1 figures are for Metric fasteners to BS3692. Steel fasteners: - Grade 8.8 for bolts, Grade 4.6 for studs, Grade 10 for
nuts; Stainless Steel fasteners: - Grade A2.
Table 2 figures are for UNC fasteners to BS1768 Steel fasteners: -Grade S and Grade 3 for nuts; Stainless Steel fasteners:
- Grade A2.
If steel fasteners are of dissimilar condition then the figures Table 1 or Table 2 must be multiplied by those in Table 3.
Table 3 Correction factors
PLATING CONDITION OF BOLT

BLACK ZINC
PLATING CONDITION OF BLACK 1.0 0.9
NUT ZINC 0.9 0.8
11.6 Thread Locking Compounds

Item Recommended compound Characteristics
Mechanical seal shaft sleeve Loctite 243 Suitable for stainless steel fasteners
locking screws Temperature range up to 150°C
Medium strength
Assembly time 15-30 minutes
42 95-0019-0000 Iss 11
11.7 Belt Tensioning

11.7.1 Force and deflection method
Belt tension is achieved by drive centre distance extension. It is achieved by applying a setting force F at the mid span of
the belt to achieve a deflection d. (see diagram and table below). Ensure the force is applied at a right angle to the belt and
evenly across the belt width.
11.7.2 Belt frequency method

Use a belt frequency meter to measure the frequency of the belt. For a new belt use the ‘as built’ column values. For a belt
with more than two or three hours service use the ‘run in’ column values. The figures are based on an ambient temperature
of 20°C.
11.7.3 Belt tension figures –HTD/Timing belts

Pump Speed Pulley Frequency
Belt type Force Deflection
type Ratio Centres (Hz)
A (mm) type F (kg) d (mm) As Built Run in
CD75 1.4 199.6 Timing 1.6 4
CD80M 2.1 303.9 Timing 2.5 6
CD75M
CD80D 1.2 200.0 HTD 2.5 4 85 70 - 80
CD100M
HL80M 1.6 287.4 Timing 2.5 6 75 60 - 70
CD103M
CD150M
CD200M
HL80M 1.3 291.8 Timing 2.5 6 85 70 - 80
NC80
NC100
NC150
CD80D 1.4 207.0 HTD 2.2 4 140 120 - 135
CD150M
CD200M
NC80, 1.4 288.0 HTD 2.4 6 95 80 - 90
NC100
NC150
HL110M
CD140M
CD160M
CD200M 1.3 300.0 HTD 1.1 6 45 30 - 40
CD225M
HL150M
HL125M
CD100M 1.6 348.0 HTD 1.4 7 65 50 - 60
11.7.4 Belt tension figures Link

Pump type Force F (kg) Deflection d (mm)
CD100M, CD103M, CD150M, CD160M, CD200M, CD225
2.6 – 3.6 6
HL80, HL110M, HL125MS, HL150M, HL150MHD, HL200M
95-0019-0000 Iss 11 43
NOTES
Godwin Pumps Ltd

Quenington
Cirencester
Gloucestershire
GL7 5BX,
England
Tel: +44 (0)1285 750271

Fax: +44 (0)1285 750352
E-mail: sales@godwinpumps.co.uk
Website: www.godwinpumps.co.uk
Godwin Pumps of America Inc.

84 Floodgate Road
Bridgeport
New Jersey 08014
U.S.A.
Tel: (001) 856 467 3636

Fax: (001) 856 467 4841
E-mail: sales@godwinpumps.com
Website: www.godwinpumps.com
44 95-0019-0000 Iss 11

Installation, Operation and Maintenance Manual CD, HL & NC Ranges Dri-Prime Pumps

Uploaded by

Installation, Operation and Maintenance Manual CD, HL & NC Ranges Dri-Prime Pumps

Uploaded by

Installation, Operation and Maintenance Manual

CD, HL & NC Ranges

Pump Serial No.

Manual No. : 95-0019-0000 Issue : 12 Date : - Nov 2011

CD75 HL80 NC80

1.2 Information for the User, Operator or Maintenance Personnel.

3 HOW TO USE THIS MANUAL

used to identify mechanical hazards

used to identify electrical hazards

NOTE: - A note is used to draw your attention to additional important information.

Figure 4 Typical lifting method for CD400 pumps

5 PUMP SERIAL NUMBER

Figure 5 Typical pump serial number plates

6.1.1 Motor Adaptor

6.1.2 Bearing Bracket

6.2.1 Alignment Procedure

Figure 6 Initial parallel alignment check

Figure 7 Angular alignment check

c) Confirming parallel alignment

Parallel alignment 1 .wmf

Figure 8 Secondary parallel alignment check

Hose line recommendations

7.2 Flooded Suction

Figure 10 Flooded suction conditions

7.3 Compressor/Vaccum pump disconnection

Figure 11 Typical blanking plate fitted in place of ejector housing

Figure 12 Side/bottom drain plug position

8.1.1 Re-greasing procedure

Figure 14 Grease nipple positions

Figure 15 Smaller pump fill and drain plugs

Figure 16 Medium sized pump fill and drain plugs

Figure 17 Larger pump fill and drain plugs

8.3.1 Front cover & pump body removal

Figure 20 Removal of front cover

Remove the pump body to expose the impeller.

Pump types CD75/ CD80D/ CD80M

Pump types NC80/ NC100/ NC150

Figure 21 Impeller retaining fittings

Insert a 65mm long 12 A/F hexagon socket bit

Figure 22 X-section showing the taper sleeve and adjustment screw

Pump types CD300M/ CD400M/ CD500M

Figure 23 Impeller Retaining fittings

8.3.3 Removing the rear wear plate

Pump types CD75/ CD80D/ CD80M/ CD100M/ CD103M/ CD150M

Pump types CD500M

8.4 Seal configuration

8.4.1 Removing the seal

Figure 24 Type 1 single mechanical seal Ø40 mechanical seal

Pump types CD300M/ CD500M

Figure 27 Type 4 one piece double mechanical seal

8.5.2 Fitting the seal

Pump types CD160M Mk 2/ CD180M/ CD300M

Pump types CD160M Mk 1/ CD400M

Pump types CD300M/ CD500M

8.5.3 Fitting the wear plate

Pump types CD500M

8.5.4 Fitting the impeller

Pump types CD75/ CD80D/ CD80M

Pump types CD300M/ CD400M/ CD500M

Pump types NC80/ NC100/ NC150

Figure 28 Impeller sleeve and adjustment screw

8.5.5 Front cover & pump body fitting

Pump types CD75/ CD80D/ CD80M/ CD100M

Pump types NC80/ NC100/ NC150

8.5.6 Preparing for service

8.6 Bearing Bracket & Motor Adaptor Dismantling

Pump types HL80/ HL100M/ HL110M/ HL125M/ HL150M/ HL200M

Pump types CD300M/ CD400M (Open Coupled)

Pump types HL130M/ HL160M/ HL225M/ HL250M/ HL260M

8.7.1 Preparation for assembly

Pump types CD75 BB Units

Pump types CD140M/ CD160M/ CD180M MA Units

Pump types CD300M/ CD400M/ CD500M

8.8.1 Filter Replacement

8.9 Vacuum Pump

8.10 Non Return Valve